LEED v4 and Sustainability Resources - cemcosteel.com v4... · LEED v4 and Sustainability Resources...

LEED v4 and Sustainability Resources

Effective 9/5/2017

Expanding Your Solutions

Table of ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

CEMCO’s Environmental Products Declaration (EPD)

Cold-Formed Steel Framing Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–14 (Structural Stud and Track Products; Interior Non-Load Bearing Stud and Track Products; ViperStud® Non-Load Bearing Stud and Track Products; Interior Drywall Framing, Furring, and Resilient Channels; Cornerbeads, Trims, and Control/Expansion Joints; Clips, Connectors, and Channels; CST, SLP-TRK® & FAS Track 1000® Head of Wall Products; ProX Header® and ProX Rough Opening Products; Sure-Span® Steel Floor Framing Products; Sure-Board® for Shear Products; USG SHAFTWALL® Products; USG Area Separation Wall Products; Expanded Metal Lath Products; Lath and Plastering Accessories)

CEMCO’s Health Product Declarations (HPD)

Health Product Declaration for CEMCO Structural Curtain Wall Studs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15–19

Health Product Declaration for CEMCO ViperStud® and ViperTrack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20–24

Health Product Declaration for CEMCO ProX Header® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25–29

Health Product Declaration for CEMCO SureSpan® Floor Joists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30–34

Health Product Declaration for CEMCO Head of Wall Slotted Tracks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35–39

Health Product Declaration for CEMCO Sure-Board® 200 and 200B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40–47

Health Product Declaration for CEMCO Sure-Board® 200W MDF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48–55

Health Product Declaration for CEMCO Metal Lath — No Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56–59

Health Product Declaration for CEMCO Metal Lath — D-Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60–66

Health Product Declaration for CEMCO Metal Lath — K-Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67–72

Health Product Declaration for CEMCO USG Shaft Wall Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73–76

Health Product Declaration for CEMCO USG Area Separation Wall Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77–81

LEED v4 and Sustainability Resources | www.cemcosteel.com | 800.775.2362 3

Introduction

LEED v4CEMCO® is pleased to join the efforts of the U .S . Green Building Council and LEED® program that improves environmental and eco-nomic performance of commercial, industrial and residential buildings . The LEED® program certifies buildings that meet standards utilizing energy, environmental design, and products as defined the LEED® rating system . The use of CEMCO products can help contribute points in specific categories . CEMCO’s products contain the following percent-ages of recycled steel content:

• Total Recycled Content: 36 .9% .

• Post-Consumer: 19 .8% .

• Pre-Consumer: 14 .4% .

LEED v4 for Building & Design Construction (effective October 31, 2016)• MR Prerequisite: Construction and Demolition Waste

Management Planning .

• MR Credit: Construction and Demolition Waste Management .

• MR Credit: Building Product Disclosure and Optimization — Sourcing of Raw Materials, Option 2 .

• MR Credit: Building Product Disclosure and Optimization — Environmental Product Declarations, Options 1 & 2 .

• MR Credit: Building Product Disclosure and Optimization — Material Ingredients, Option 1 .

• MR Credit: Building Life-Cycle Impact Reduction, Option 4 .

CEMCO’s Environmental Product Declaration (EPD)CEMCO is one of the few manufacturers of cold-formed steel framing and metal lath products and accessories to offer our own EPD for your use in qualifying for LEED v4 certification . Submitting CEMCO’s EPD on your project can double the points awarded . CEMCO’s Environmental Product Declaration (EPD) covers the following products:

• Structural Stud and Track Products .

• Interior Non-Load Bearing Stud and Track Products .

• ViperStud® Non-Load Bearing Stud and Track Products .

• Interior Drywall Framing, Furring, and Resilient Channels .

• Cornerbeads, Trims, and Control/Expansion Joints .

• Clips, Connectors, and Channels .

Introduction | LEED v4 and Sustainability Resources

• CST, SLP-TRK® & FAS Track 1000® Head of Wall Products .

• ProX Header® and ProX Rough Opening Products .

• Sure-Span® Steel Floor Framing Products .

• Sure-Board® for Shear Products .

• USG SHAFTWALL® Products .

• USG Area Separation Wall Products .

• Expanded Metal Lath Products .

• Lath and Plastering Accessories .

CEMCO’s Health Product Declarations (HPD)To provide you with the most accurate and transparent information about our products, CEMCO has published the following Health Prod-uct Declarations (HPD’s) for you to include in your LEED v4 applications . Each HPD is specific to one of the several product groups CEMCO’s manufactures right here in the United States at one of our four state-of-the-art manufacturing facilities . As we continue to expand our product lines by introducing new and innovative products and systems, we will add their HPD’s to this list below:

• Health Product Declaration for CEMCO Structural Curtain Wall Studs .

• Health Product Declaration for CEMCO ViperStud® and ViperTrack .

• Health Product Declaration for CEMCO ProX Header® .

• Health Product Declaration for CEMCO SureSpan® Floor Joists .

• Health Product Declaration for CEMCO Head of Wall Slotted Tracks .

• Health Product Declaration for CEMCO Sure-Board® 200 and 200B .

• Health Product Declaration for CEMCO Sure-Board® 200W MDF .

• Health Product Declaration for CEMCO Metal Lath — No Paper .

• Health Product Declaration for CEMCO Metal Lath — D-Paper .

• Health Product Declaration for CEMCO Metal Lath — K-Paper .

• Health Product Declaration for CEMCO USG Shaft Wall Systems .

• Health Product Declaration for CEMCO USG Area Separation Wall Systems .

LEED v4 and Sustainability Resources | www.cemcosteel.com | 800.775.23624

ENVIRONMENTAL PRODUCT DECLARATION

61TCOLD-FORMED STEEL FRAMING SYSTEMSSTRUCTURAL STUD AND TRACK, VIPERSTUDP®P INTERIOR FRAMING, PROX HEADER P®P,SUREBOARDP®P, SURE-SPAN P®P FLOOR JOIST FRAMING SYSTEM, CST, SLP-TRKP®P, FAS TRACKP®P 1000 SLOTTED TRACKS, USG SHAFTWALL CH/H-STUD STUDS AND TRACK

56TCEMCO’s Sure-Span P

®P and cold-formed steel framing products installed in a mid-rise

project in San Francisco, home to 5% of the world's LEED certified projects.

CEMCO produces a complete line of steel framing products in its four U.S. manufacturing facilities, primarily from American-made steel.

62TCalifornia Expanded Metal Products Co., more commonly known as CEMCOP®P, is your premier source for steel framing products, metal lath products, and plastering accessories. All CEMCO products are made in the USA in one of our four state-of-the-art manufacturing facilities. 62TSteel, one of the world’s most recycled materials, is the basis for all of CEMCO’s products, which are manufactured from mill-certified hot-dip galvanized steel,giving the industry confidence that CEMCO’s products are among the best choice for your green building needs. 62TFor additional information, visit www.cemcosteel.com.


Cold-Formed Steel Framing, Metal Lath and AccessoriesCold-Formed Steel Framing Systems According to ISO 14025

This declaration is an environmental product declaration (EPD) in accordance with ISO 14025. EPDs rely on Life Cycle Assessment (LCA) to provide information on a number of environmental impacts of products over their life cycle. UExclusions U: EPDs do not indicate that any environmental or social performance benchmarks are met, and there may be impacts that they do not encompass. LCAs do not typically address the site-specific environmental impacts of raw material extraction, nor are they meant to assess human health toxicity. EPDs can complement but cannot replace tools and certifications that are designed to address these impacts and/or set performance thresholds – e.g. Type 1 certifications, health assessments and declarations, environmental impact assessments, etc. UAccuracy of Results U: EPDs regularly rely on estimations of impacts, and the level of accuracy in estimation of effect differs for any particular product line and reported impact. UComparabilityU: EPDs are not comparative assertions and are either not comparable or have limited comparability when they cover different life cycle stages, are based on different product category rules or are missing relevant environmental impacts. EPDs from different programs may not be comparable.

PROGRAM OPERATOR UL Environment DECLARATION HOLDER CEMCODECLARATION NUMBER 4787356941.101.1

DECLARED PRODUCT

REFERENCE PCR SCS PCR for Designated Steel Construction Products v1 2015DATE OF ISSUE July 13, 2016PERIOD OF VALIDITY 5 Years

CONTENTS OF THE DECLARATION

Product definition and information about building physicsInformation about basic material and the material’s originDescription of the product’s manufactureIndication of product processingInformation about the in-use conditionsLife cycle assessment resultsTesting results and verifications

The PCR review was conducted by: PCR Review Panel Chair: Thomas Gloria

This declaration was independently verified in accordance with ISO 14025 by Underwriters Laboratories

☐ INTERNAL ☒ EXTERNAL Wade Stout, UL Environment

This life cycle assessment was independently verified in accordance with ISO 14044 and the reference PCR by:

Thomas Gloria, Industrial Ecology Consultants

Cold-Formed Steel Framing Systems


Cold-Formed Steel Framing, Metal Lath and AccessoriesCold-Formed Steel Framing Systems According to ISO 14025

Product Definition

Company Description

Since 1974, CEMCO P®

P has taken a leadership role to provide you the most advanced products and systems for steel framing and metal lath construction. Delivering the safest products we can produce, such as the new Safety Edged P

®P

steel framing products, gives you safer handling of framing products on your trucks, in your yards, and on your jobsites. CEMCO P

®P also manufactures FAS Track P

®P 1000, DDAP

®P angles, and slotted track for your fire-rated head-of-wall

applications. Other innovations such as SureBoard P®

P for shear-walls, Sure-SpanP®

P steel floor joists and the ProX Header P

®P and ProX Rough-Opening framing systems are also available to help complete your environmentally

responsible project. CEMCO’s four state-of-the-art manufacturing facilities are located in City of Industry, CA (Metropolitan Los Angeles); Denver, CO; Ft. Worth, TX; and Pittsburg, CA (Oakland/San Francisco Bay Area).

Product Description

The CEMCO P®

P steel framing & metal lath products covered by this EPD are:

Structural Stud and Track (ICC-ES ESR 3016) Manufactured for the use in curtain wall, load-bearing,

rough-opening & ceiling/floor/roof applications Available in typical c-shaped sections ranging in thickness

from 33 mils to 118 mils

ViperStud P

®P Interior Framing (ICC-ES ESR 2620 & ATI-ES 0154)

Proprietary interior framing system using high-strength steel to increase overallperformance

Available in c-shaped sections ranging in thickness from 15 mils to 33 mils

ProX Header P

®P (IAPMO ER-0286)

Proprietary header/rough-opening system designed to use less material and increasesafety

Available in sections ranging in thickness from 33 mils to 68 mils

Material & Coatings:

CEMCO®

uses only hot-dip

galvanized steel


Cold-Formed Steel Framing, Metal Lath and Accessories Cold-Formed Steel Framing Systems

According to ISO 14025

SureBoard P

®P for Shear panels (IAPMO ER-0126)

Steel sheet/gypsum sheathing product designed specifically for wall shear applications Sure-Span P

®P Floor Joist Framing System (ESR PENDING)

Proprietary steel floor joist/roof rafter framing system with extra-large flared punch-outs for greater access of HVAC, MEP, and TELCOM conduits

Available in proprietary c-shaped sections ranging in thickness from 43 mils to 97 mils CST, SLP-TRK P

®P, and FAS Track P

®P 1000 Brand Slotted Tracks (ICC-ES ESR 2012)

Head of Wall top tracks designed for seismic and fire-abatement assemblies Available in c-shaped sections in thicknesses ranging from 33 mils to 68 mils

USG SHAFTWALL Brand CH and H-Stud Studs and Track (AER 09038) USG’s CH studs and J-Runners for shaftwall and stairwell applications USG’s H-Stud and C-Runner for area separation wall assemblies




Expanded Metal Lath Products (ICC-ES ESR 1623) Manufactured for the use in exterior and interior applications for 3-coat stucco

assemblies Available in various flat, self-furred, ribbed, and paper-backed versions

Plastering Accessories (ICC-ES ESR 1623*) Various profiles used in conjunction with expanded metal lath products Products designed and manufactured for casing, corners, control joints, expansion

joints, screeds, and weeps

Drywall/Interior Accessories (ICC-ES ESR 3016*) Product designed for use with interior non-load bearing stud framing systems Products include angles, drywall finishing trims, flat straps, furring channels, and

resilient channels Connectors, Clips, and Channels (ICC-ES ESR 3016*) Various connectors and clips used for connecting structural and non-structural steel

framing components Products included are clip angles, corner angles/ledgers, diagonal tension strapping,

gusset plates, slide clips, and u-shaped channels

* Select products, see report for details




Manufacturing Steps

The manufacturing steps for CEMCO® steel framing systems are shown in the flow diagram below.

Framing System Options

PRODUCT SIZES THICKNESS (MILS)

Structural 1-5/8” – 14” Stud & Track 33, 43, 54, 68, 97, 118

ViperStudP

® 1-5/8” – 6” Stud & Track 15, 20, 21, 30, 33

ProX HeaderP

® 3-5/8” – 8” Headers & Inserts 33, 43, 54, 68

SureBoardP

® 48” x 96”, 108”, 120”, or 144” 27

Sure-SpanP

® 7-1/4” – 14” Joists and Rim-Track 33, 43, 54, 68, 97

CST, SLP-TRKP

®P, and FAS TrackP

®P 1000 2-1/2” – 8” Slotted Tracks 33, 43, 54, 68

USG SHAFTWALL Brand CH and H-Stud Studs and Track 2-1/2” – 6” CH & H-Studs, J-Runner & C-Runner 18, 24, 33, 34

Expanded Metal Lath 27-1/2” x 48” or 96” 1.75, 2.5, or 3.4 lbs/ydP

2

Plastering Accessories Various 18 through 33

Drywall Interior Accessories Various 11 through 33

Connectors, Clips, and Channels Various 33, 43, 54, 68, 97, 118

Coil Slitting Decoiling Slitting Recoiling

Roll Forming Packaging Loading




Application and Codes of Practice

Material Specification (ASTM)

ViperStudP

®P Nonstructural Framing Members and Accessories A653/A1003

Structural Framing Members and Accessories A653/A1003

ProX Header P

®P Framing Members and Accessories A653/A1003

SureBoardP

®P A653/A1003

Sure-SpanP

®P Framing Members and Accessories A653/A1003

CST, SLP-TRKP

®P & FAS Track 1000P

®P Slotted Tracks A653/A1003

USG Shaftwall Members A653/A1003

Expanded Metal Lath Products A653/A1003

Plastering Accessories A653/A1003

Product Specification (ASTM)

Drywall Nonstructural Framing Members and Accessories C645

Structural Framing Members and Accessories C955

ProX Header P

®P Framing Members and Accessories C955

SureBoardP

®P C645

Sure-SpanP

®P Framing Members and Accessories C955

CST, SLP-TRKP


®P Slotted Tracks C645

USG Shaftwall Members C645

Expanded Metal Lath Products C847

Plastering Accessories C1047

Coating Specification (ASTM)*

ViperStudP

®P Nonstructural Framing Members and Accessories A653/A924/A1003

Structural Framing Members and Accessories A653/A924/A1003

ProX Header P

®P Framing Members and Accessories A653/A924/A1003

SureBoardP

®P A653/A924

Sure-SpanP

®P Framing Members and Accessories A653/A924/A1003

CST, SLP-TRKP


®P Slotted Tracks A653/A924/A1003

USG Shaftwall Members A653/A924/A1003

Expanded Metal Lath Products A653/A924/A1003

* CEMCOP

®P ONLY USES HOT-DIP GALVANIZED

CEMCO® products are not expected to

create exposure conditions that exceed safe

thresholds for health impacts to

humans or flora/fauna under normal operating

conditions.




Life Cycle Assessment – Product System and Modeling

A “cradle-to-gate” analysis using life cycle assessment (LCA) techniques was conducted for this EPD. The analysis was done according to the product category rule (PCR) for Designated Steel Construction Products and followed LCA principles, requirements and guidelines laid out in the ISO 14040/14044 standards. As such, EPDs of construction products may not be comparable if they do not comply with the same PCR. While the intent of the PCR is to increase comparability, there may still be differences among EPDs that comply with the same PCR (e.g., due to differences in system boundaries, background data, etc.).

Declared Unit

The declared unit for an EPD is one metric ton of steel construction product.

System Boundaries

The “cradle-to-gate” life cycle stages represent the product stage (information modules A1-A3) and include

A1: all extraction and processing of raw materials; any reuse of products or materials from a previous product system; processing of secondary materials; and any energy recovery or other recovery processes from secondary fuels;

A2: all transportation to the factory gate and all internal transport; A3: production of all ancillary materials, pre‐products, products, and co‐products, including any packaging;

generation of electricity from primary energy resources, including upstream processes.

Product Stage Construction Stage Use Stage End-of-Life Stage

A1 A2 A3 A4 A5 B1 B2 B3 B4 B5 C1 C2 C3 C4

Raw

mat

eria

ls

supp

ly

Tran

spor

t

Man

ufac

turin

g

Tran

spor

t

Inst

alla

tion

Use

Mai

nten

ance

Rep

air

Rep

lace

men

t

Ref

urbi

shm

ent

De-

cons

truct

ion

Tran

spor

t

Was

te

proc

essi

ng

Dis

posa

l

This EPD represents 2012 steel framing production by CEMCO in four US plants (City of Industry and Pittsburg, CA; Denver, CO; and Forth Worth, TX).

Name Required Unit Optional Unit Declared Unit metric ton short ton Density kg/m P

3 lb/ftP

3

EXCLUDED FROM THIS STUDY




Assumptions

No significant assumptions have been made. All of the raw materials and energy inputs have been modeled using processes and flows that closely follow actual production raw materials and processes. All of the material and energy flows have been accounted.

Allocation

No multi-output (i.e., co-product) allocation was performed in this study. Allocation of background data (energy and materials) taken from the GaBi 2016 databases is documented online at http://www.gabi-software.com/international/support/gabi/.

Cut-off Criteria

The cut-off criteria for including or excluding materials, energy and emissions data of the study are as follows:

Mass: If a flow is less than 1% of the cumulative mass of the model it may be excluded, providing its environmental relevance is not a concern.

Energy: If a flow is less than 1% of the cumulative energy of the model it may be excluded, providing its environmental relevance is not a concern.

Environmental relevance: If a flow meets the above criteria for exclusion, yet is thought to potentially have a significant environmental impact, it was included.

No processes were neglected or excluded. Capital items for the production processes (machines, buildings, etc.) were not taken into consideration.

Transportation

UInbound: For hot-dip galvanized steel inputs, a weighted average transport distance was applied based on each plant’s fraction of total production and based on each plant’s primary steel supplier’s location. As a result, the weighted average distance is 315 miles by rail and 11 miles by heavy-duty truck. Lubricant, propane and packaging inputs were each assigned an estimated transport distance of 100 miles. UOutbound: U Transport distances to local waste management sites were estimated at 20 miles. Transportation to distribution centers or installation sites falls outside of the scope of this “cradle-to-gate” study.




Other Environmental Information

Parameter Unit Value Hazardous waste disposed metric ton 5.21E-10 Non-hazardous waste disposed metric ton 1.09E-04 Radioactive waste disposed metric ton 6.00E-04 Components for re‐use metric ton 0 Materials for recycling metric ton 5.02E-02 Materials for energy recovery metric ton 0 Exported energy MJ per energy carrier 0

Visualization of Life Cycle Impact Assessment

The diagrams below illustrate the degree to which the modules drive the major impact categories.

Data Quality Assessment

Temporal representativeness: All primary data were collected for the year 2012. All secondary data come from the GaBi 2016 databases and are representative of the years 2007-2015. Therefore, temporal representativeness is warranted. Geographical representativeness: All primary and secondary data were collected specific to the countries or regions under study. Where country-specific or region-specific data were unavailable, proxy data were used. Geographical representativeness is considered to be high. Technological representativeness: All primary and secondary data were modeled to be specific to the technologies or technology mixes under study. Where technology-specific data were unavailable, proxy data were used. Technological representativeness is considered to be high. Precision: As the majority of the relevant foreground data are measured data or calculated based on primary information sources of the owner of the technology, precision is considered to be high. All background data are sourced from GaBi databases with the documented precision.

Primary Energy Demand from Non-Renewable Resources

A1 A2 A3

95%

96%

97%

98%

99%

100%

GWP ODP AP EP POCP

Impact Assessment Categories

A1 A2 A3




Disclaimer: This Environmental Product Declaration (EPD) conforms to ISO 14025, ISO 14040, ISO 14044, and ISO 21930. Scope of Results Reported: The PCR requires the reporting of a limited set of LCA metrics; therefore, there may be relevant environmental impacts beyond those disclosed by this EPD. The EPD does not indicate that any environmental or social performance benchmarks are met nor thresholds exceeded. Accuracy of Results: This EPD has been developed in accordance with the PCR applicable for the identified product following the principles, requirements and guidelines of the ISO 14040, ISO 14044, ISO 14025 and ISO 21930 standards. The results in this EPD are estimations of potential impacts. The accuracy of results in different EPDs may vary as a result of value choices, background data assumptions and quality of data collected. Comparability: EPDs are not comparative assertions and are either not comparable or have limited comparability when they cover different life cycle stages, are based on different product category rules or are missing relevant environmental impacts. Such comparisons can be inaccurate, and could lead to the erroneous selection of materials or products which are higher‐impact, at least in some impact categories. Any comparison of EPDs shall be subject to the requirements of ISO 21930. For comparison of EPDs which report different module scopes, such that one EPD includes Module D and the other does not, the comparison shall only be made on the basis of Modules A1, A2 and A3. Additionally, when Module D is included in the EPDs being compared, all EPDs must use the same methodology for calculation of Module D values. Contact Information

CEMCO Technical Services Department: (800) 416-2278

LCA Development

The EPD and background LCA were prepared with support from thinkstep, Inc.


Structural / Curtain Wall Studs & Track by CEMCO ®

Health Product

Declaration v2.0

CLASSIFICATION: 05 40 00 METALS (BEAMS): COLD-FORMED METAL FRAMING created via: HPDC Online Builder

PRODUCT DESCRIPTION: CEMCO EXTERIOR STRUCTURAL STUDS AND TRACK ARE MANUFACTURED FROM MILL CERTIFIED GALVANIZED PRIME STEEL, AND ARE DESIGNED FOR USE IN CURTAIN-WALL AND LOAD BEARING APPLICATIONS. THICKNESSES RANGE FROM 33 MIL (20 GA) TO 118 MIL (10 GA). FLANGE OR LEG SIZES FOR BOTH STUDS AND TRACK RANGE FROM 1 ¼” TO 3 ½”. THESE PRODUCTS ARE PRODUCED WITH A STANDARD G60 COATING, BUT ARE ALSO AVAILABLE WITH A G90 COATING UPON SPECIAL REQUEST. CEMCO'S STRUCTURAL FRAMING PRODUCTS ARE MANUFACTURED TO THE STRICT TOLERANCES SET FORTH BY THE 2015 AND 2012 IBC, AND VERIFIED BY ICC-ES ESR-3016; STRUCTURAL FRAMING MEMBERS & ACCESSORIES MATERIAL SPECIFICATION (ASTM) A1003/A653/A924; PRODUCT SPECIFICATION (ASTM) C955; COATING SPECIFICATION (ASTM) A1003/A653/A924. ALL CEMCO PRODUCTS ARE MANUFACTURED IN THE USA AT ONE OF OUR FOUR STATE-OF-THE-ART PRODUCTION FACILITIES STRATEGICALLY LOCATED IN FOUR MAJOR METROPOLITAN MARKETS TO ENSURE THAT SERVICE AND QUALITY REQUIREMENTS ARE MET. ALSO INCLUDES CSI MASTERFORMAT 05 12 23 METALS (BEAMS): STRUCTURAL STEEL FOR BUILDINGS.

Section 1: Summary

CONTENT INVENTORY

Threshold per material

100 ppm 1,000 ppm Per GHS SDS Per OSHA MSDS Other

Residuals and impuritiesconsidered in 1 of 1 materials

see Section 2: Material Notes

see Section 5: General Notes

Based on the selected Content Inventory Threshold:

Characterized....................................................Are the Percent Weight and Role provided for all substances? Yes NoScreened.........................................................Are all substances screened using Priority Hazard Lists with results disclosed?

Yes No

Identified......................................................Are all substances disclosed by Name (Specific or Generic) and Identifier?

Yes No

CONTENT IN DESCENDING ORDER OF QUANTITY

Summary of product contents and results from screening individual chemical substances against HPD Priority Hazard Lists and the GreenScreen for Safer Chemicals®. The HPD does not assess whether using or handling this product will expose individuals to its chemical substances or any health risk. Refer to Section 2 for further details.

MATERIAL | SUBSTANCE | RESIDUAL OR IMPURITYGREENSCREEN SCORE | HAZARD TYPE

HOT-DIPPED GALVANIZED STEEL (G60) [ STEEL UNKZINC LT-P1 | AQU | RES | PHY ]

Number of Greenscreen BM-4/BM3 contents.......... 0Contents highest concern GreenScreenBenchmark or List translator Score.............. LT-P1Nanomaterial............. No

INVENTORY AND SCREENING NOTES:

This Health Product Declaration (HPD) was completed in accordance with the HPD Standard version 2.0, and discloses hazards associated with all substances present at or above 1000 parts per million (ppm) in the finished product. Therefore, this HPD qualifies for the LEED v4 MR credit Building Product Disclosure and Optimization: Material Ingredient Reporting (Option 1).

VOLATILE ORGANIC COMPOUND (VOC) CONTENT

VOC Content data is not applicable for this product category.

CERTIFICATIONS AND COMPLIANCEOther: ICC-ES Evaluation Report Multi-attribute: Environmental Product Declaration

See Section 3 for additional listings.

Self-Published* VERIFIER: SCREENING DATE: December 1, 2016 EXPIRY DATE*: December 1, 2019 Third Party Verified VERIFICATION #: RELEASE DATE: December 1, 2016 * or within 3 months of significant change in product contents

*See HPDC website for details

Structural / Curtain Wall Studs & Track Health Product Declaration Page 1 of 5 created via: HPDC Online Builder www.hpd-collaborative.org


Section 2: Content in Descending Order of Quantity

This section lists materials in a product and the substances in each material based on the Inventory Threshold for each material. If residuals or impurities from the manufacturing or extraction processes are considered for a material, these are inventoried and characterized to the extent described in the Material and/or General Notes. Chemical substances are screened against the HPD Priority Hazard Lists for human and environmental health impacts. Screening is based on best available information; "Not Found" does not necessarily mean there is no potential hazard associated with the product or its contents. More information about Priority Hazard Lists and the GreenScreen can be found online: www.hpd-collaborative.org and www.greenscreenchemicals.org.



HOT-DIPPED GALVANIZED STEEL (G60) %: 100.0000 HPD URL:Inventory Threshold: 1000 ppm Residuals Considered: YesMaterial Notes: Steel is considered a Generic Commodity Material by the Health Product Declaration Collaborative. Specific guidelines are being created to address known issues related to transparency and disclosure for several materials (“Special Conditions”), including Metal Alloys such as steel. This HPD will be updated as appropriate when the guidelines for Steel are released. No residuals or impurities are known or expected to be present in this material above the inventory threshold indicated. Passivation coatings for corrosion resistance are an industry standard for this type of material; however, the substances used for such coatings fall below the inventory threshold (0.1% or 1000 ppm) of the material, and are therefore not reported here.

STEEL ID: 12597-69-2

%: 97.4000 - 99.1000 GS: UNK RC: Both NANO: NO ROLE: Base Metal

HAZARDS: AGENCY(IES) WITH WARNINGS:

None Found No warnings found on HPD Priority lists

SUBSTANCE NOTES: CEMCO cold-formed steel framing products contain 30% to 35% pre- and post-consumer recycled steel sourced from several domestic (USA) suppliers.

ZINC ID: 7440-66-6

%: 0.9000 - 2.6000 GS: LT-P1 RC: None NANO: NO ROLE: Metallic Coating


ACUTE AQUATIC EU - R-phrases R50 - Very Toxic to Aquatic Organisms

RESPIRATORY AOEC - Asthmagens Asthmagen (ARs) - sensitizer-induced - inhalable forms only

ACUTE AQUATIC EU - GHS (H-Statements) H400 - Very toxic to aquatic life

CHRON AQUATIC EU - GHS (H-Statements) H410 - Very toxic to aquatic life with long lasting effects

PHYSICAL HAZARD (REACTIVE)

EU - GHS (H-Statements) H250 - Catches fire spontaneously if exposed to air


EU - GHS (H-Statements) H260 - In contact with water releases flammable gases which may ignite spontaneously

SUBSTANCE NOTES: Form-specific hazards not expected to apply to the finished and installed product. However, further processing (e.g. welding, sawing, etc) during installation may release fumes or other respirable particles. The Safety Data Sheet (SDS) for Galvanized Sheet Steel can be found at http://cemcosteel.com/cemco-specifications.

Section 3: Certifications and Compliance

This section lists applicable certification and standards compliance information for VOC emissions and VOC content. Other types of health or environmental performance testing or certifications completed for the product may be provided.

OTHER ICC-ES Evaluation Report



CERTIFYING PARTY: Third PartyAPPLICABLE FACILITIES: City of Industry, CA 91746 Pittsburg, CA 94565 Denver, CO 80204 Fort Worth, TX 76140CERTIFICATE URL: www.icc-es.org/reports/pdf_files/ICC-ES/ESR-3016.pdfCERTIFICATION AND COMPLIANCE NOTES: ESR-3016. Evaluation Subject: Cold-formed Steel Framing. Evaluation Scope includes compliance with the following codes: 2015, 2012 International Building Code® (IBC); 2015, 2012 International Residential Code® (IRC); 2013 California Building Code (CBC); 2013 California Residential Code (CRC); 2014 and 2010 Florida Building Code—Building; 2014 and 2010 Florida Building Code—Residential.

ISSUE DATE: 2014-07-01

EXPIRY DATE: 2016-07-01

CERTIFIER OR LAB: ICC Evaluation Service

MULTI-ATTRIBUTE Environmental Product Declaration

CERTIFYING PARTY: Third PartyAPPLICABLE FACILITIES: City of Industry, CA; Pittsburg, CA; Denver, CO; Forth Worth, TXCERTIFICATE URL: www.cemcosteel.com/sites/default/files/CEMCOs%20Environmental%20Product%20Declaration_EPD.pdfCERTIFICATION AND COMPLIANCE NOTES: Declaration number: 4787356941.101.1. Environmental Product Declaration covers the following CEMCO Cold-Formed Steel Framing Systems, including: Structural Stud and Track (ICC-ES ESR 3016); ViperStud®P P Interior Framing (ICC-ES ESR 2620 & ATI-ES 0154); ProX Header®P P (IAPMO ER-0286); SureBoard®P P for Shear panels (IAPMO ER- 0126); Sure-Span®P P Floor Joist Framing System (ESR PENDING); CST, SLP-TRK®P P, and FAS Track®P P 1000 Brand Slotted Tracks (ICC-ES ESR 2012); USG SHAFTWALL Brand CH and H-Stud Studs and Track (AER 09038); Expanded Metal Lath Products (ICC-ES ESR 1623); Plastering Accessories (ICC-ES ESR 1623); Drywall/Interior Accessories (ICC-ES ESR 3016); Connectors, Clips, and Channels (ICC-ES ESR 3016).



CERTIFIER OR LAB: UL Environment

Section 4: Accessories

This section lists related products or materials that the manufacturer requires or recommends for installation (such as adhesives or fasteners), maintenance, cleaning, or operations. For information relating to the contents of these related products, refer to their applicable Health Product Declarations, if available.

FURRING CHANNELS HPD URL: No HPD availableCONDITION WHEN RECOMMENDED OR REQUIRED AND/OR OTHER NOTES: Used to furr-out during installation. As per ICC-ES Report ESR-3016, "Furring channels are cold-formed from galvanized steel coils conforming to ASTM A1003, Nonstructural Grade 33 (NS33), with a minimum metallic coating listed for Type NS in Table 1 of ASTM A1003."

U-CHANNELS HPD URL: No HPD availableCONDITION WHEN RECOMMENDED OR REQUIRED AND/OR OTHER NOTES: Attach to studs during installation for bridging. According to the ICC-ES Report ESR-3016: "U-channels are cold-formed from galvanized steel coils conforming to ASTM A653, SS Grade 33; or ASTM A1003, Structural Grade 33, Type H (ST33H), with a minimum metallic coating listed for Type H and Type L in Table 1 of ASTM A1003."

Section 5: General Notes



Section 6: References

MANUFACTURER INFORMATION

MANUFACTURER: CEMCO

ADDRESS: 13191 Crossroads Pkwy. North Suite 325 City of Industry, CA 91746 USA

WEBSITE: www.cemcosteel.com

CONTACT NAME: Fernando Sesma

TITLE: Director of Technical Services

PHONE: 800.416.2278

EMAIL: [email protected]

KEY

OSHA MSDS Occupational Safety and Health Administration Material Safety Data SheetGHS SDS Globally Harmonized System of Classi cation and Labeling of Chemicals Safety Data Sheet

Hazard TypesAQU Aquatic toxicityCAN CancerDEV Developmental toxicityEND Endocrine activityEYE Eye irritation/corrosivityGEN Gene mutation

GLO Global warmingMAM Mammalian/systemic/organ toxicityMUL Multiple hazardsNEU NeurotoxicityOZO Ozone depletionPBT Persistent Bioaccumulative Toxic

PHY Physical Hazard (reactive)REP Reproductive toxicityRES Respiratory sensitizationSKI Skin sensitization/irritation/corrosivityLAN Land ToxicityNF Not found on Priority Hazard Lists

GreenScreen (GS)BM-4 Benchmark 4 (prefer-safer chemical)BM-3 Benchmark 3 (use but still opportunity for improvement) BM-2 Benchmark 2 (use but search for safer substitutes)BM-1 Benchmark 1 (avoid - chemical of high concern)BM-U Benchmark Unspeci ed (insu cient data to benchmark)

LT-P1 List Translator Possible Benchmark 1LT-1 List Translator Likely Benchmark 1LT-UNK List Translator Benchmark Unknown (insufficient information from List Translator lists to benchmark)UNK Unknown (no data on List Translator Lists)

Recycled TypesPreC Preconsumer (Post-Industrial)PostC PostconsumerBoth Both Preconsumer and PostconsumerUnk Inclusion of recycled content is unknownNone Does not include recycled content

OtherNano Composed of nanoscale particles or nanotechnology

Declaration LevelSelf-declared Manufacturerʼs self-declaration (First Party)Independent Lab Manufacturerʼs self-declaration using results from an independent labSecond Party Verification by trade association or other interested partyThird Party Verification by independent certifierApplicable facilities Manufacturing sites to which testing applies

The Health Product Declaration (HPD) Open Standard provides for the disclosure of product contents and potential associated human and environmental health hazards. Hazard associations are based on the HPD Priority Hazard Lists, the GreenScreen List Translator, and when available, full GreenScreen assessments. The HPD Open Standard does not provide an assessment of health impacts throughout the product life cycle. It does not provide an assessment of exposure or risk associated with product handling or use. It also does not address potential health impacts of: (i) substances used or created during the manufacturing process unless they remain in the nal product, or (ii) substances created after the product is delivered for end use (e.g., if the product burns, degrades, or otherwise changes chemical composition).

The HPD Open Standard was created and is maintained and evolved by the Health Product Declaration Collaborative (the HPD Collaborative), a customer-led organization composed of stakeholders throughout the building industry. The HPD Collaborative is committed to the continuous improvement of building products through transparency, openness, and innovation throughout the product supply chain.

A disclosure completed in compliance with the HPD Open Standard is referred to as a “Health Product Declaration,” or “HPD.” The product manufacturer and any applicable independent veri er are solely responsible for the accuracy of statements and claims made in this HPD and for compliance with the HPD Open Standard noted.



ViperStud & ViperTrack by CEMCO ®

Health Product

Declaration v2.0

CLASSIFICATION: 09 22 16.00 FINISHES: NON-STRUCTURAL METAL FRAMING created via: HPDC Online Builder

PRODUCT DESCRIPTION: THE VIPERSTUD® DRYWALL FRAMING SYSTEM OFFERS ALL THE BENEFITS OF CONVENTIONAL FLAT STEEL STUDS WITH A DESIGN THAT PERFORMS EVEN BETTER. VIPERSTUDS AND VIPERTRACKS CONSIST OF 100% HOT-DIP GALVANIZED STEEL, AND ARE USED FOR FRAMING OF INTERIOR NONLOAD-BEARING COMPOSITE AND NON-COMPOSITE WALLS. VIPERTRACKS® ARE FABRICATED IN 1-5/8", 2-1/2", 3-5/8", 4", AND 6" WIDTHS WITH 1-1/4" LEGS FROM STANDARD G40 HOT-DIPPED GALVANIZED STEEL. VIPERSTUDS® ARE FABRICATED IN 1-5/8", 2-1/2", 3-5/8", 4", AND 6" WIDTHS FROM STANDARD G40 HOT-DIPPED GALVANIZED STEEL; G60 AND G90 COATINGS ARE AVAILABLE UPON REQUEST. VIPER 25, VIPER18 MIL, VIPER20 (.0195 MIN), VIPER20 (.0209 MIN), VIPER 30MIL, AND VIPER 33MIL MANUFACTURED BY CEMCO RECEIVED AN EVALUATION REPORT (CCRR-0154) FROM ATI EVALUATION SERVICES AND AN EVALUATION REPORT (ESR-2620) FROM ICC EVALUATION SERVICE (ICC-ES), PROVIDING EVIDENCE THAT THE VIPERSTUD DRYWALL FRAMING SYSTEM MEETS CODE REQUIREMENTS. VIPERSTUD DRYWALL NONSTRUCTURAL FRAMING MEMBERS & ACCESSORIES MATERIAL SPECIFICATION (ASTM) A1003/A653/A924; PRODUCT SPECIFICATION (ASTM) C645; COATING SPECIFICATION (ASTM) A1003/A653/A924. ALL CEMCO PRODUCTS ARE MANUFACTURED IN THE USA AT ONE OF OUR FOUR STATE-OF-THE-ART PRODUCTION FACILITIES STRATEGICALLY LOCATED IN FOUR MAJOR METROPOLITAN MARKETS TO ENSURE THAT SERVICE AND QUALITY REQUIREMENTS ARE MET. ALSO INCLUDES THE FOLLOWING CSI MASTERFORMAT: 09 21 16.23 FINISHES: GYPSUM BOARD SHAFT WALL ASSEMBLIES.

Section 1: Summary

CONTENT INVENTORY








Yes No


Yes No










CERTIFICATIONS AND COMPLIANCEOther: ICC-ES Evaluation Report Multi-attribute: Environmental Product Declaration




ViperStud & ViperTrack Health Product Declaration Page 1 of 5 created via: HPDC Online Builder www.hpd-collaborative.org



STEEL ID: 12597-69-2





ZINC ID: 7440-66-6














OTHER ICC-ES Evaluation Report



CERTIFYING PARTY: Third PartyAPPLICABLE FACILITIES: City of Industry, CA 91746 Pittsburg, CA 94565 Denver, CO 80204 Fort Worth, TX 76140CERTIFICATE URL: www.icc-es.org/reports/pdf_files/ESR-2620.pdfCERTIFICATION AND COMPLIANCE NOTES: ESR-2620. Evaluation Subject: ViperStud Drywall Framing System (Nonload-Bearing): Viper25, Viper 20, Viper 18mil, Viper 27mil, Viper 30mil, Viper 33mil. Evaluation Scope includes compliance with the following codes: 2012, 2015 International Building Code® (IBC); 2015 International Residential Code® (IRC); 2010 Florida Building Code—Building; 2010 Florida Building Code—Residential.





CERTIFYING PARTY: Third PartyAPPLICABLE FACILITIES: City of Industry, CA; Pittsburg, CA; Denver, CO; Forth Worth, TXCERTIFICATE URL: www.cemcosteel.com/sites/default/files/CEMCOs%20Environmental%20Product%20Declaration_EPD.pdfCERTIFICATION AND COMPLIANCE NOTES: Declaration number: 4787356941.101.1. Environmental Product Declaration covers the following CEMCO Cold-Formed Steel Framing Systems, including: Structural Stud and Track (ICC-ES ESR 3016); ViperStud®P P Interior Framing (ICC-ES ESR 2620 & ATI-ES 0154); ProX Header®P P (IAPMO ER-0286); SureBoard®P P for Shear panels (IAPMO ER-0126); Sure-Span®P P Floor Joist Framing System (ESR PENDING); CST, SLP-TRK®P P, and FAS Track®P P 1000 Brand Slotted Tracks (ICC-ES ESR 2012); USG SHAFTWALL Brand CH and H-Stud Studs and Track (AER 09038); Expanded Metal Lath Products (ICC-ES ESR 1623); Plastering Accessories (ICC-ES ESR 1623); Drywall/Interior Accessories (ICC-ES ESR 3016); Connectors, Clips, and Channels (ICC-ES ESR 3016).






GYPSUM WALLBOARD HPD URL: See Other Notes (Below)CONDITION WHEN RECOMMENDED OR REQUIRED AND/OR OTHER NOTES: For installation of drywall framing system. According to ICC-ES ESR-2620: "Gypsum wallboard must be a minimum of 5/8 inch (15.9 mm) thick and Type X, complying with ASTM C1396 and manufactured by one of the following companies: American Gypsum; CertainTeed; Georgia Pacific; Lafarge; National Gypsum; Temple-Inland; or USG."

FASTENERS HPD URL: No HPD availableCONDITION WHEN RECOMMENDED OR REQUIRED AND/OR OTHER NOTES: Fasteners for attaching the gypsum wallboard to the studs and tracks. According to ICC-ES ESR 2620: "must be No. 6, Type S, fine thread drywall bugle head screws conforming to ASTM C1002."






MANUFACTURER: CEMCO





PHONE: 800.416.2278


KEY















ProX Header ® by CEMCO

Health Product

Declaration v2.0


PRODUCT DESCRIPTION: PROX HEADER® IS A SUPERIOR HEADER SYSTEM THAT PROVIDES A WINNING COMBINATION OF SIMPLE CODE COMPLIANCE, EASY MEMBER SELECTION, AND FAST INSTALLATION. PROX HEADER IS A LIGHT GAUGE STEEL HEADER THAT PROVIDES HORIZONTAL AND VERTICAL LOAD SUPPORT. THIS PRE-ENGINEERED METAL FRAMING COMPONENT IS DESIGNED AS A 1- OR 2-PIECE STEEL HEADER THAT CAN BE USED IN LIEU OF 4- OR 5-PIECE BUILT-UP (STUD AND TRACK) HEADERS IN BOTH INTERIOR AND EXTERIOR APPLICATIONS, INCLUDING DOOR AND WINDOW OPENINGS. IT ALSO WORKS AT ANY FRAMED OPENING IN THE WALL, SUCH AS HVAC OPENINGS AND OTHER WALL PENETRATIONS. PROX HEADER CLIPS ARE INTERNAL AND CONNECT HORIZONTAL TO VERTICAL MEMBERS, WHICH LEAVES A SMOOTH FRAMING SUBSTRATE FOR THE DRYWALL AND FINISHING TRADES. THE PROX HEADER IS MADE OF 33 TO 68 MIL GALVANIZED STEEL WITH A STANDARD G60 COATING, AND COMPLIES WITH INDUSTRY STANDARD ASTM PERFORMANCE CRITERIA FOR METAL STUD FRAMING: ASTM C645, A653/A653M, C754 (INSTALLATION & STORAGE), A924/A924M, A1003/A1003M/E119; IAPMO ER-0286; IBC 2012/2015 AND CBC 2013 CODE COMPLIANT. PROX HEADER® IS A REGISTERED TRADEMARK OF BRADY INNOVATIONS, LLC. THIS HPD COVERS PROX HEADER (OUTER), PROX HEADER (INSERT), AND PROX HEADER CLIPS.

Section 1: Summary

CONTENT INVENTORY








Yes No


Yes No







This Health Product Declaration (HPD) was completed in accordance with the HPD Standard version 2.0, and discloses hazards associated with all substances present at or above 1000 parts per million (ppm) in the finished product, as well as the role and percent by weight. Therefore, this HPD qualifies for the LEED v4 MR credit Building Product Disclosure and Optimization: Material Ingredient Reporting (Option 1).



CERTIFICATIONS AND COMPLIANCEOther: UES Evaluation Report Multi-attribute: Environmental Product Declaration




ProX Header Health Product Declaration Page 1 of 5 created via: HPDC Online Builder www.hpd-collaborative.org


HOT-DIPPED GALVANIZED STEEL (G60) %: 100.0000 HPD URL:Inventory Threshold: 1000 ppm Residuals Considered: YesMaterial Notes: Steel is considered a Generic Commodity Material by the Health Product Declaration Collaborative. Specific guidelines are being created to address known issues related to transparency and disclosure for several materials (“Special Conditions”), including Metal Alloys such as steel. This HPD will be updated as appropriate when the guidelines for Steel are released. No residuals or impurities are known or expected to be present in this material above the inventory threshold indicated. Steel is considered essentially inert for the purposes of Pharos toxics scoring (Pharos CML), with no known hazardous impurities (Quartz Database). Passivation coatings for corrosion resistance are an industry standard for this type of material; however, the substances used for such coatings fall below the inventory threshold declared for the material, and are therefore not reported here.

STEEL ID: 12597-69-2





ZINC ID: 7440-66-6














OTHER UES Evaluation Report



CERTIFYING PARTY: Third PartyAPPLICABLE FACILITIES: City of Industry, CA 91746; Pittsburg, CA 94565; Denver, CO 80204; Fort Worth, TX 76140CERTIFICATE URL: www.iapmoes.org/Documents/ER_0286.pdfCERTIFICATION AND COMPLIANCE NOTES: IAPMO ER-286. Scope of Evaluation includes compliance to the following codes & regulations: 2012 International Building Code® (IBC); 2013 California Building Code® (CBC). Evaluated in accordance with: ICC-ES AC261; ICC-ES AC46. Properties assessed: Structural.



CERTIFIER OR LAB: Uniform Evaluation Service


CERTIFYING PARTY: Third PartyAPPLICABLE FACILITIES: City of Industry, CA; Pittsburg, CA; Denver, CO; Forth Worth, TXCERTIFICATE URL: www.cemcosteel.com/sites/default/files/CEMCOs%20Environmental%20Product%20Declaration_EPD.pdfCERTIFICATION AND COMPLIANCE NOTES: Declaration number: 4787356941.101.1. Environmental Product Declaration covers the following CEMCO Cold-Formed Steel Framing Systems, including: Structural Stud and Track (ICC-ES ESR 3016); ViperStud®P P Interior Framing (ICC-ES ESR 2620 & ATI-ES 0154); ProX Header®P P (IAPMO ER-0286); SureBoard®P P for Shear panels (IAPMO ER-0126); Sure-Span®P P Floor Joist Framing System (ESR PENDING); CST, SLP-TRK®P P, and FAS Track®P P 1000 Brand Slotted Tracks (ICC-ES ESR 2012); USG SHAFTWALL Brand CH and H-Stud Studs and Track (AER 09038); Expanded Metal Lath Products (ICC-ES ESR 1623); Plastering Accessories (ICC-ES ESR 1623); Drywall/Interior Accessories (ICC-ES ESR 3016); Connectors, Clips, and Channels (ICC-ES ESR 3016).






STEEL STUD SUPPORTS (JAMB STUDS) HPD URL: No HPD availableCONDITION WHEN RECOMMENDED OR REQUIRED AND/OR OTHER NOTES: According to IAPMO ER-286: "Located on both ends of the header, on each side of the wall opening the ProX Header shall be supported by steel jamb studs. The steel jamb stud thickness and grade of steel shall equal or exceed the ProX Header member properties, with the exception of jamb studs supporting 68-mil-thick (1.73 mm) ProX Headers, which may be minimum 54 mils (1.37 mm) thick. The vertical jamb stud may be installed as a single (wide flange) jamb stud, double jamb stud or triple jamb stud system. The load capacity and jamb stud system used shall be designed, and installation shall be in accordance with the IBC."

FASTENERS HPD URL: No HPD availableCONDITION WHEN RECOMMENDED OR REQUIRED AND/OR OTHER NOTES: According to IAPMO ER-286: "Fasteners used in this system shall be self- drilling sheet metal screws complying with ASTM C1513 or listed in an evaluation report issued by an approved and accredited evaluation service agency. The No. 8 screws shall have minimum shear and tensile allowable loads of 344 pounds (1.53 kN) and 118 pounds (0.52 kN), respectively. The No. 10 screws shall have minimum shear and tensile allowable loads of 370 pounds (1.64 kN) and 137 pounds (0.61 kN), respectively."






MANUFACTURER: CEMCO





PHONE: 800.416.2278


KEY















Sure-Span Floor Joists by CEMCO ®

Health Product

Declaration v2.0


PRODUCT DESCRIPTION: CEMCOʼS SURE-SPAN® STEEL FLOOR JOIST SYSTEM IS A PATENTED, TESTED, AND APPROVED SOLUTION FOR COMMERCIAL, MID-RISE, AND RESIDENTIAL FLOOR FRAMING ASSEMBLIES. SURE-SPAN FLOOR JOISTS ARE MANUFACTURED WITH EXTRA LARGE OPENINGS (PUNCH-OUTS) TO ALLOW FOR MECHANICAL, ELECTRICAL, AND PLUMBING ACCESS WITHOUT DAMAGING THE STRUCTURAL INTEGRITY OF THE FLOOR FRAMING SYSTEM. SURE-SPAN PROVIDES LONG AND STURDY FLOOR SPANS, ALONG WITH FIRE-RESISTANT AND SOUND-REDUCING SOLUTIONS FOR ARCHITECTS, ENGINEERS, AND DEVELOPERS. THIS HPD COVERS "SSCJ" PUNCHED C-JOISTS AND “SSRT” RIM TRACK WITH PRE-SPACED CLIPS. "SSCJ" SURE-SPAN FLOOR JOISTS ARE MANUFACTURED WITH EITHER A 1-3/4" OR 2" FLANGE, IN THICKNESSES RANGING FROM 43 MIL TO 97 MIL. THE CORRESPONDING "SSRT" SURE-SPAN RIM TRACKS ARE MANUFACTURED WITH EITHER A 2” LEG/FLANGE, IN THICKNESSES RANGING FROM 43 MIL TO 97 MIL, AND ARE PRODUCED WITH PRE-SPACED CLIPS AT 12, 16, 19.2 OR 24 INCH ON-CENTER CONFIGURATIONS FOR EASE OF INSTALLATION. ALL CEMCO SURE-SPAN PRODUCTS ARE MANUFACTURED FROM HOT-DIPPED GALVANIZED STEEL IN G60 COATING (G90 AVAILABLE UPON SPECIAL REQUEST), AND MEET OR EXCEED RELEVANT ASTM, AISI, AND UL STANDARDS.

Section 1: Summary

CONTENT INVENTORY








Yes No


Yes No







This Health Product Declaration (HPD) was completed in accordance with the HPD Standard version 2.0, and discloses hazards associated with all substances present at or above 1000 parts per million (ppm) in the finished product, as well as the role and percent by weight. Therefore, this HPD qualifies for the LEED v4 MR credit Building Product Disclosure and Optimization: Material Ingredient Reporting (Option 1).



CERTIFICATIONS AND COMPLIANCEMulti-attribute: Environmental Product Declaration




Sure-Span Floor Joists Health Product Declaration Page 1 of 5 created via: HPDC Online Builder www.hpd-collaborative.org



STEEL ID: 12597-69-2





ZINC ID: 7440-66-6























“SB” SURE-BRIDGING HPD URL: No HPD availableCONDITION WHEN RECOMMENDED OR REQUIRED AND/OR OTHER NOTES: Used during installation of Sure-Span Floor Joist System to improve structural strength. “SB” Sure-Bridging is fabricated in 43 mil thickness with 1-5/16” flanges and 2-1/2” webs. Each is made in specific lengths to properly fit between the joists based upon the on-center spacing with 1-3/4” tabs to ensure proper fastening. Sure-Bridging can be used with joists having either 1-3/4” or 2” flanges only. CEMCO Sure-Bridging members are produced from hot-dipped galvanized steel in standard G60 coating. G90 is available upon special request.






MANUFACTURER: CEMCO





PHONE: 800.416.2278


KEY















Head of Wall - Slotted Tracks by CEMCO ®

Health Product

Declaration v2.0

CLASSIFICATION: 05 40 00 METALS: COLD-FORMED METAL FRAMING created via: HPDC Online Builder

PRODUCT DESCRIPTION: THIS HPD COVERS THE FOLLOWING CEMCO HEAD OF WALL PRODUCTS: “CST” AND “SLP-TRK®” SLOTTED SLIP TRACKS; EXTERIOR SLOTTED TRACK (EST); TAB TRACK. CEMCOʼS "CST" BRAND SLOTTED TRACK AND SLIPTRACK SYSTEMʼS “SLP-TRK®” BRAND SLOTTED TRACK ARE EVALUATED AND APPROVED FOR USE BY ICC IN REPORT ESR-2012, AND ARE AVAILABLE WITH OPTIONAL DRIFT SLOTS. “CST” AND “SLP-TRK®” ARE PRODUCED FROM G40 (18 AND 33 MIL) AND G60 (43, 54, 68 MIL) COATED STEEL. CEMCO EXTERIOR SLOTTED TRACK (EST) IS A VERTICAL DEFLECTION TRACK MEMBER. THE EXTERNAL GROOVE PROVIDES A RESTING POINT FOR SHEATHING, TRANSFERRING THE WEIGHT OF THE SHEATHING TO THE FRAMING MEMBER, AND THE 2” WEB SLOTS PROVIDE DRIFT MOVEMENT CAPABILITIES. CEMCO EST IS FABRICATED FROM HOT-DIPPED GALVANIZED STEEL COMPLYING WITH ASTM A653, AND ASTM A1003 STRUCTURAL GRADE 50 TYPE H FOR GRADE 33 TYPE H FOR WITH A MINIMUM G60 COATING, AND COMPLIES WITH ASTM C645. CEMCO TAB TRACK PROVIDES A NON MECHANICAL (SCREWLESS) STUD-TO-TRACK ATTACHMENT FOR METAL STUD WALL FRAMING. A SERIES OF 1" LONG TABS ARE EVENLY SPACED ACROSS THE TRACKʼS LEGS PROVIDING FLEXIBILITY TO REGULAR AND IRREGULAR LAYOUT. ONCE THE STUDS ARE NESTED WITHIN THE TAB TRACK, THE TABS MAY BE PUSHED INWARD ON EITHER SIDE OF THE STUD TO PROHIBIT LATERAL MOVEMENT WHILE MAINTAINING VERTICAL DEFLECTION. AVAILABLE IN 33 MIL THICKNESSES, TAB TRACK IS MANUFACTURED FROM G40 HOT-DIPPED GALVANIZED STEEL.

Section 1: Summary

CONTENT INVENTORY








Yes No


Yes No




HOT-DIPPED GALVANIZED STEEL (G40 & G60) [ STEEL UNK ZINC LT-P1 | AQU | RES | PHY ]






CERTIFICATIONS AND COMPLIANCEMulti-attribute: Environmental Product Declaration Other: ICC-ES Evaluation Report




Head of Wall - Slotted Tracks Health Product Declaration Page 1 of 5 created via: HPDC Online Builder www.hpd-collaborative.org


HOT-DIPPED GALVANIZED STEEL (G40 & G60) %: 100.0000 HPD URL:Inventory Threshold: 1000 ppm Residuals Considered: YesMaterial Notes: Steel is considered a Generic Commodity Material by the Health Product Declaration Collaborative. Specific guidelines are being created to address known issues related to transparency and disclosure for several materials (“Special Conditions”), including declaration of Recycled Content. This HPD will be updated as appropriate when the guidelines for Steel are released. No residuals or impurities are known or expected to be present in this material above the inventory threshold indicated. Passivation coatings for corrosion resistance are an industry standard for this type of material; however, the substances used for such coatings fall below the inventory threshold (0.1% or 1000 ppm) of the material, and are therefore not reported here.

STEEL ID: 12597-69-2





ZINC ID: 7440-66-6





















OTHER ICC-ES Evaluation ReportCERTIFYING PARTY: Third PartyAPPLICABLE FACILITIES: City of Industry, CA 91746 Pittsburg, CA 94565 Denver, CO 80204 Fort Worth, TX 76140CERTIFICATE URL: www.icc-es.org/reports/pdf_files/ESR-2012.pdfCERTIFICATION AND COMPLIANCE NOTES: ESR-2012. Evaluation Subject: CEMCO Steel Tracks Expansion Joint System for Non-Load Bearing Wall Systems. Evaluation Scope includes compliance with the following code: 2015 and 2012 International Building Code® (IBC).






GYPSUM WALLBOARD HPD URL: See Other Notes (Below)CONDITION WHEN RECOMMENDED OR REQUIRED AND/OR OTHER NOTES: For installation of drywall framing system. According to ICC- ES ESR-2012: "The 5/8-inch-thick (15.9 mm), Type X gypsum wallboard must comply with ASTM C1396". HPDs for Gypsum Wallboard may be found at: http://www.hpd-collaborative.org/hpd-public-repository/

FASTENERS HPD URL: No HPD AvailableCONDITION WHEN RECOMMENDED OR REQUIRED AND/OR OTHER NOTES: Used to attach the tops of studs to CST/SLP-TRK®. According to ICC- ES ESR-2012: Fasteners "must be minimum No. 8 by 9/16-inch-long (14.3 mm), wafer-head, self-piercing tapping or self-drilling tapping, as applicable, steel screws complying with ASTM C 1513-13."






MANUFACTURER: CEMCO





PHONE: 800.416.2278


KEY















Sure-Board® Series 200 & Series 200B by CEMCO

Health Product

Declaration v2.0

CLASSIFICATION: 05 10 00 METALS: STRUCTURAL METAL FRAMING created via: HPDC Online Builder

PRODUCT DESCRIPTION: SURE-BOARD® HAS A GYPSUM BOARD FACING THAT INTEGRATES WITH STANDARD GYPSUM BOARD FOR A SMOOTH UNINTERRUPTED FINISH. SURE-BOARD® REQUIRES NO LEVELING AND IS READY FOR FINISHES. SURE-BOARD® LAYS FLAT ON THE STUD SURFACE WITH NO SAGGING, LEAVING NO SURFACE IRREGULARITIES. WHEN SURE-BOARD® IS USED, THERE IS NO NEED FOR ADDITIONAL STRUCTURAL SHEATHING OR TENSION STRAP BRACES, REQUIRING COSTLY AND LABORIOUS PRE AND POST TENSIONING. SURE-BOARD® SERIES 200 STRUCTURAL PANELS CONSIST OF 1/2", 5/8" OR 3/4" (12.7, 15.9 OR 19.1 MM) THICK SQUARE OR TAPERED-EDGE TYPE X OR TYPE C FIRE RATED GYPSUM WALLBOARD OR WATER RESISTANT CORE SHEATHING COMPLYING WITH ASTM C 1369, AS WELL AS GLASSMAT GYPSUM SUBSTRATE COMPLYING WITH ASTM C 1177, AND FIBER REINFORCED GYPSUM PANELS COMPLYING WITH ASTM C 1278; LAMINATED WITH WATER SOLUBLE ADHESIVE TO STEEL SHEET. STEEL THICKNESSES AVAILABLE: 33 MIL WITH G40, G60 OR G90 COATING; 43 MIL, 54 MIL, 68 MIL, 97 MIL AND 118 MIL WITH G60 OR G90 COATING. THIS HPD COVERS SURE- BOARD® SERIES 200 AND SURE-BOARD® SERIES 200B PRODUCTS USING PAPER-FACED GYPSUM BOARD ONLY.

Section 1: Summary

CONTENT INVENTORY








Yes No


Yes No




GYPSUM BOARD [ GYPSUM LT-UNK CELLULOSE, MICROCRYSTALLINE UNK WATER BM-4 CALCIUM SULFATE DIHYDRATE LT-UNK QUARTZ LT-1 | CAN VERMICULITE UNKSTARCH LT-UNK NAPHTHALENESULFONIC ACID, FORMALDEHYDE POLYMER, CALCIUM SALT LT-UNKSTYRENE BUTADIENE RUBBER (SBR) LT-UNK ] HOT-DIPPED GALVANIZED STEEL [ STEEL UNK ZINC LT-P1 | AQU | MUL | PHY ] ADHESIVE [ UNDISCLOSED LT-UNK UNDISCLOSED LT-UNK WATER BM-4 UNDISCLOSED LT-1 | CAN | MUL UNDISCLOSED LT-UNK ]

Number of Greenscreen BM-4/BM3 contents.......... 2Contents highest concern GreenScreenBenchmark or List translator Score.............. LT-1Nanomaterial............. No


This Health Product Declaration (HPD) was completed in accordance with the HPD Standard version 2.0, and discloses hazards associated with all substances present at or above 1000 parts per million (ppm) for Galvanized Steel, and at or above 100 ppm for the Adhesive, which together represent ~30-40% of the finished product. As Sure-Board® Series 200/200B Structural Panels can be manufactured with gypsum wallboard from various suppliers, the material content information provided for Gypsum Board is based on that available via the Quartz Common Product Database for "Drywall (Natural Gypsum)". HPDs that include information specific to a particular brand/type of Gypsum Board may be available in the future.



CERTIFICATIONS AND COMPLIANCEMulti-attribute: Environmental Product Declaration Other: UES Evaluation Report (ER-0126)


Self-Published* VERIFIER: SCREENING DATE: February 20, 2017 EXPIRY DATE*: February 20, 2020 Third Party Verified VERIFICATION #: RELEASE DATE: February 20, 2017 * or within 3 months of significant change in product contents


Sure-Board® Series 200 & Series 200B Health Product Declaration Page 1 of 8 created via: HPDC Online Builder www.hpd-collaborative.org




GYPSUM BOARD %: 61.7000 - 74.1000 HPD URL:Inventory Threshold: Other Residuals Considered: YesMaterial Notes: Sure-Board® Series 200/200B Structural Panels can be manufactured with gypsum wallboard from various suppliers; thus, the substances for Gypsum Board are disclosed to 1000 ppm based on information provided by Quartz Common Product Database for "Drywall (Natural Gypsum)". Residuals/Impurities that are known or expected to be present above this threshold have been disclosed, based on information provided by Quartz Database. An industry-wide Environmental Product Declaration (Type III EPD) for "Typical (5/8" Type X) North American Gypsum Boards" is available at: www.gypsum.org/wp-content/uploads/2013/12/Gypsum-2014-FINAL-May-13-.pdf

GYPSUM ID: 13397-24-5

%: 88.1000 GS: LT-UNK RC: None NANO: NO ROLE: Body



SUBSTANCE NOTES:

CELLULOSE, MICROCRYSTALLINE ID: 9004-34-6

%: 4.4000 GS: UNK RC: None NANO: NO ROLE: Paper



SUBSTANCE NOTES: Listed by Quartz Database as "Waste Paper" from cardboard boxes, newspapers, and kraft cuttings.

WATER ID: 7732-18-5

%: 3.2000 GS: BM-4 RC: None NANO: NO ROLE: Binder



SUBSTANCE NOTES: Moisture content of finished product = 3.3% per Athena 2011.

CALCIUM SULFATE DIHYDRATE ID: 10101-41-4



%: 1.9000 GS: LT-UNK RC: None NANO: NO ROLE: Filler, Accelerator



SUBSTANCE NOTES:

QUARTZ ID: 14808-60-7

%: Impurity/Residual GS: LT-1 RC: None NANO: NO ROLE: Impurity/Residual


CANCER US CDC - Occupational Carcinogens Occupational Carcinogen

CANCER CA EPA - Prop 65 Carcinogen - specific to chemical form or exposure route

CANCER IARC Group 1: Agent is carcinogenic to humans - inhaled from occupational sources

CANCER US NIH - Report on Carcinogens Known to be Human Carcinogen (respirable size - occupational setting)

CANCER MAK Carcinogen Group 1 - Substances that cause cancer in man

SUBSTANCE NOTES:

VERMICULITE ID: 1318-00-9

%: 0.5000 GS: UNK RC: None NANO: NO ROLE: Fire Resistance



SUBSTANCE NOTES: Listed as standard ingredient in regular wallboard by Athena 2011.

STARCH ID: 9005-25-8

%: 0.4000 GS: LT-UNK RC: None NANO: NO ROLE: Accelerator, Binder, Edge Paste



SUBSTANCE NOTES:



NAPHTHALENESULFONIC ACID, FORMALDEHYDE POLYMER, CALCIUM SALT ID: 37293-74-6

%: 0.3000 GS: LT-UNK RC: None NANO: NO ROLE: Dispersant



SUBSTANCE NOTES: From Quartz Database: Formaldehyde polymer, calcium salt, Formaldehyde-based, percentages are of dispersant formulation and will need to be adjusted; "The naphthalenesulfonate dispersant is present in an amount of about 0.1%-0.3% by weight based on the weight of dry stucco." (USG patent)

STYRENE BUTADIENE RUBBER (SBR) ID: 9003-55-8

%: 0.2000 GS: LT-UNK RC: None NANO: NO ROLE: Binder



SUBSTANCE NOTES: Quartz Database lists as "Polymer Latex", and states the following: "SBR is a representative material stand in for things described as SBR latex, latex, or acrylic. There is variation of the exact polymer used between manufacturers."

HOT-DIPPED GALVANIZED STEEL %: 25.9000 - 38.3000 HPD URL:Inventory Threshold: 1000 ppm Residuals Considered: YesMaterial Notes: Steel is considered a Generic Commodity Material by the Health Product Declaration Collaborative. Specific guidelines are being created to address known issues related to transparency and disclosure for several materials (“Special Conditions”), including Metal Alloys such as steel. This HPD will be updated as appropriate when the guidelines for Steel are released. No residuals or impurities are known or expected to be present in this material above the inventory threshold indicated. Steel is considered essentially inert for the purposes of Pharos toxics scoring (Pharos CML), with no known hazardous impurities (Quartz Database). Passivation coatings for corrosion resistance are an industry standard for this type of material; however, the substances used for such coatings fall below the inventory threshold declared for the material, and are therefore not reported here.

STEEL ID: 12597-69-2




SUBSTANCE NOTES: Consists of 36.9% Recycled Content, including 14.4% Pre-Consumer and 19.8% Post-Consumer Recycled Steel.

ZINC ID: 7440-66-6








MULTIPLE German FEA - Substances Hazardous to Waters Class 2 - Hazard to Waters





SUBSTANCE NOTES: These form-specific hazards are not expected to apply once the product is in place. However, exposure to particulates and/or fumes may be possible during installation (e.g. from grinding, sawing, welding, etc.) See most current Safety Data Sheet (SDS) for more information.

ADHESIVE %: 1.4000 - 2.1000 HPD URL:Inventory Threshold: 100 ppm Residuals Considered: YesMaterial Notes: No Residuals/Impurities are known or expected to be present at or above the Inventory Threshold listed, based on Supplier Disclosure Letter.

UNDISCLOSED

%: 80.0000 - 90.0000 GS: LT-UNK RC: None NANO: NO ROLE: Polymer



SUBSTANCE NOTES: Supplier has shared substance name and CAS number in confidentiality; substance to remain proprietary to supplier. Substance has been screened against HPD Priority Lists with results disclosed.

UNDISCLOSED

%: 10.0000 - 15.0000 GS: LT-UNK RC: None NANO: NO ROLE: Plasticizer




WATER ID: 7732-18-5

%: 1.0000 - 5.0000 GS: BM-4 RC: None NANO: NO ROLE: Diluent





SUBSTANCE NOTES:

UNDISCLOSED

%: 0.1000 - 0.5000 GS: LT-1 RC: None NANO: NO ROLE: Raw Material


CANCER EU - R-phrases R45 - May cause cancer

CANCER EU - GHS (H-Statements) H350 - May cause cancer

CANCER EU - REACH Annex XVII CMRs Carcinogen Category 2 - Substances which should be regarded as if they are Carcinogenic to man

MULTIPLE ChemSec - SIN List CMR - Carcinogen, Mutagen &/or Reproductive Toxicant

MULTIPLE German FEA - Substances Hazardous to Waters Class 3 - Severe Hazard to Waters

CANCER EU - Annex VI CMRs Carcinogen Category 1B - Presumed Carcinogen based on animal evidence


UNDISCLOSED

%: 0.0100 - 0.0500 GS: LT-UNK RC: None NANO: NO ROLE: Raw Material









CERTIFYING PARTY: Third PartyAPPLICABLE FACILITIES: City of Industry, CA; Pittsburg, CA; Denver, CO; Forth Worth, TXCERTIFICATE URL: www.cemcosteel.com/sites/default/files/CEMCOs%20Environmental%20Product%20Declaration_EPD.pdfCERTIFICATION AND COMPLIANCE NOTES: Declaration number: 4787356941.101.1. Environmental Product Declaration covers the following CEMCO Cold-Formed Steel Framing Systems, including: Structural Stud and Track (ICC-ES ESR 3016); ViperStud® Interior Framing (ICC-ES ESR 2620 & ATI-ES 0154); ProX Header® (IAPMO ER-0286); SureBoard® for Shear Panels (IAPMO ER- 0126); Sure-Span® Floor Joist Framing System (ESR PENDING); CST, SLP-TRK®, and FAS Track® 1000 Brand Slotted Tracks (ICC-ES ESR 2012); USG SHAFTWALL Brand CH and H-Stud Studs and Track (AER 09038); Expanded Metal Lath Products (ICC-ES ESR 1623); Plastering Accessories (ICC-ES ESR 1623); Drywall/Interior Accessories (ICC-ES ESR 3016); Connectors, Clips, and Channels (ICC-ES ESR 3016).




OTHER UES Evaluation Report (ER-0126)CERTIFYING PARTY: Third PartyAPPLICABLE FACILITIES: City of Industry, CA 91746; Pittsburg, CA 94565; Denver, CO 80204; Fort Worth, TX 76140CERTIFICATE URL: http://www.iapmoes.org/Documents/ER_0126.pdfCERTIFICATION AND COMPLIANCE NOTES: IAPMO ER-0126. Scope of Evaluation includes compliance to the following codes & regulations: 2015, 2012, and 2009 International Building Code® (IBC); 2015, 2012, and 2009 International Residential Code® (IRC); 2016 and 2013 California Building Code® (CBC). Evaluated in accordance with EC 003-2016. Properties assessed: Structural.






FASTENERS HPD URL: No HPD availableCONDITION WHEN RECOMMENDED OR REQUIRED AND/OR OTHER NOTES: Used to attach Sure-Board® Structural Panels to Framing. See IAPMO ER-0126 report for specific fastener requirements: http://www.iapmoes.org/Documents/ER_0126.pdf






MANUFACTURER: CEMCO





PHONE: 800.416.2278


KEY










The Health Product Declaration (HPD) Open Standard provides for the disclosure of product contents and potential associated human and environmental health hazards. Hazard associations are based on the HPD Priority Hazard Lists, the GreenScreen List Translator, and when available, full GreenScreen assessments. The HPD Open Standard does not provide an assessment of health impacts throughout the product life cycle. It does not provide an assessment of exposure or risk associated with product handling or use. It also does not address potential health impacts of: (i) substances used or created during the manufacturing process unless they remain in the final product, or (ii) substances created after the product is delivered for end use (e.g., if the product burns, degrades, or otherwise changes chemical composition).


A disclosure completed in compliance with the HPD Open Standard is referred to as a “Health Product Declaration,” or “HPD.” The product manufacturer and any applicable independent verifier are solely responsible for the accuracy of statements and claims made in this HPD and for compliance with the HPD Open Standard noted.



Sure-Board® Series 200W by CEMCO

Health Product

Declaration v2.0

CLASSIFICATION: 05 10 00 METALS: STRUCTURAL METAL FRAMING created via: HPDC Online Builder

PRODUCT DESCRIPTION: SURE-BOARD® SERIES 200W FOR STEEL FRAMING AND SERIES 200W FOR WOOD FRAMING ARE STEEL SHEET AND MEDIUM DENSITY FIBERBOARD (MDF) COMPOSITE PRODUCTS THAT ARE INSTALLED ON STEEL OR WOOD FRAMED SHEAR WALLS AT POINTS REQUIRING SHEAR. SURE-BOARD® ELIMINATES USE OF EXCESS MATERIALS AND LABOR, WHICH LOWERS COST AND INCREASES PERFORMANCE. LATERAL AND ELASTIC DISPLACEMENT AT ALLOWABLE VALUES ARE SIGNIFICANTLY LESS USING SURE-BOARD® SERIES 200W FOR WOOD FRAME CONSTRUCTION. ON EXTERIOR WALLS, THE USE OF SURE-BOARD® SERIES 200W GUARANTEES YOUR EXTERIOR PLASTER WILL MAINTAIN A CONSISTENT THICKNESS WITHOUT ADDITIONAL FURRING. ALL TESTING FOR SURE-BOARD® SERIES 200W WAS PERFORMED USING ASTM E 2126 SPD REVERSE CYCLIC TEST PROTOCOL. THE STEEL SHEET IS NO. 22 GAUGE/0.027" (0.686 MM) MINIMUM BASE-METAL THICKNESS, COMPLYING WITH ASTM A 653 CS, GRADE 33, AND IS PROVIDED WITH G40 MINIMUM HOT-DIPPED GALVANIZED COATING CONFORMING WITH ASTM A924. THIS HPD COVERS SURE-BOARD® SERIES 200W PRODUCTS USING 1/8" MDF ONLY.

Section 1: Summary

CONTENT INVENTORY








Yes No


Yes No




HOT-DIPPED GALVANIZED STEEL [ STEEL UNKZINC LT-P1 | AQU | MUL | PHY ] MEDIUM DENSITY FIBERBOARD (MDF) [ WOOD FIBER - UNSPECIFIED UNK UREA FORMALDEHYDE LT-UNK | RES PARAFFIN LT-UNK UREA LT-UNK FORMALDEHYDE LT-1 | MAM | SKI | CAN | RES | GEN | MUL | END ]ADHESIVE [ UNDISCLOSED LT-UNK UNDISCLOSED LT-UNK WATER BM-4 UNDISCLOSED LT-1 | CAN | MUL UNDISCLOSED LT-UNK ]

Number of Greenscreen BM-4/BM3 contents.......... 1Contents highest concern GreenScreenBenchmark or List translator Score.............. LT-1Nanomaterial............. No


This Health Product Declaration (HPD) was completed in accordance with the HPD Standard version 2.0, and discloses hazards associated with all substances present at or above 1000 parts per million (ppm) for Galvanized Steel, and at or above 100 ppm for the Adhesive, which together represent ~70-80% of the finished product. As Sure-Board® Series 200W Structural Panels can be manufactured with medium density fiberboard (MDF) from various suppliers, the material content information provided for the 1/8" MDF is based on that available via the Quartz Common Product Database. HPDs that include information specific to a particular brand/type of MDF may be available in the future.



CERTIFICATIONS AND COMPLIANCEMulti-attribute: Environmental Product Declaration Other: UES Evaluation Report (ER-0126)


Self-Published* VERIFIER: SCREENING DATE: February 7, 2017 EXPIRY DATE*: February 7, 2020 Third Party Verified VERIFICATION #: RELEASE DATE: March 2, 2017 * or within 3 months of significant change in product contents


Sure-Board® Series 200W Health Product Declaration Page 1 of 8 created via: HPDC Online Builder www.hpd-collaborative.org




HOT-DIPPED GALVANIZED STEEL %: 73.6000 HPD URL:Inventory Threshold: 1000 ppm Residuals Considered: YesMaterial Notes: Steel is considered a Generic Commodity Material by the Health Product Declaration Collaborative. Specific guidelines are being created to address known issues related to transparency and disclosure for several materials (“Special Conditions”), including Metal Alloys such as steel. This HPD will be updated as appropriate when the guidelines for Steel are released. No residuals or impurities are known or expected to be present in this material above the inventory threshold indicated. Steel is considered essentially inert for the purposes of Pharos toxics scoring (Pharos CML), with no known hazardous impurities (Quartz Database). Passivation coatings for corrosion resistance are an industry standard for this type of material; however, the substances used for such coatings fall below the inventory threshold declared for the material, and are therefore not reported here.

STEEL ID: 12597-69-2





ZINC ID: 7440-66-6











SUBSTANCE NOTES: These form-specific hazards are not expected to apply once the product is in place. However, exposure to particulates and/or fumes may be possible during installation (e.g. from grinding, sawing, welding, etc.) See most current Safety Data Sheet (SDS) for more information.



MEDIUM DENSITY FIBERBOARD (MDF) %: 22.3000 HPD URL:Inventory Threshold: Other Residuals Considered: YesMaterial Notes: As Sure-Board® Series 200W Structural Panels can be manufactured with medium density fiberboard (MDF) from various suppliers, substances for MDF are disclosed to 1000 ppm based on information provided by Quartz Common Product Database. Residuals/Impurities that are known or expected to be present above this threshold have been disclosed, based on information provided by Quartz Database. An industry-wide Environmental Product Declaration (EPD) for MDF can be found at: www.awc.org/pdf/greenbuilding/epd/AWC-EPD-MDF-1311.pdf

WOOD FIBER - UNSPECIFIED ID:

%: 89.1000 GS: UNK RC: None NANO: NO ROLE: Substrate



SUBSTANCE NOTES:

UREA FORMALDEHYDE ID: 9011-05-6

%: 10.0000 GS: LT-UNK RC: None NANO: NO ROLE: Binder Resin


RESPIRATORY AOEC - Asthmagens Asthmagen (Rs) - sensitizer-induced

SUBSTANCE NOTES: Quartz Project lists the Respiratory hazard as "occupational only".

PARAFFIN ID: 8002-74-2

%: 0.6000 GS: LT-UNK RC: None NANO: NO ROLE: Water Resistance



SUBSTANCE NOTES:

UREA ID: 57-13-6

%: 0.1600 GS: LT-UNK RC: None NANO: NO ROLE: Binder Component; Formaldehyde Scavenger



SUBSTANCE NOTES:



FORMALDEHYDE ID: 50-00-0

%: Impurity/Residual GS: LT-1 RC: None NANO: NO ROLE: Impurity/Residual


MAMMALIAN EU - R-phrases R23 - Toxic by Inhalation (gas, vapour, dust/mist)

MAMMALIAN EU - R-phrases R24 - Toxic in Contact with Skin

MAMMALIAN EU - R-phrases R25 - Toxic if Swallowed

SKIN IRRITATION EU - R-phrases R34 - Causes burns

CANCER EU - R-phrases R40 - Limited Evidence of Carcinogenic Effects

SKIN SENSITIZE EU - R-phrases R43 - May cause sensitization by skin contact

RESPIRATORY AOEC - Asthmagens Asthmagen (G) - generally accepted

CANCER US EPA - IRIS Carcinogens (1986) Group B1 - Probable human Carcinogen

CANCER IARC Group 1 - Agent is Carcinogenic to humans

CANCER CA EPA - Prop 65 Carcinogen


CANCER US NIH - Report on Carcinogens Known to be a human Carcinogen

MAMMALIAN EU - GHS (H-Statements) H301 - Toxic if swallowed

MAMMALIAN EU - GHS (H-Statements) H311 - Toxic in contact with skin

SKIN IRRITATION EU - GHS (H-Statements) H314 - Causes severe skin burns and eye damage

SKIN SENSITIZE EU - GHS (H-Statements) H317 - May cause an allergic skin reaction

MAMMALIAN EU - GHS (H-Statements) H331 - Toxic if inhaled

GENE MUTATION EU - GHS (H-Statements) H341 - Suspected of causing genetic defects



ENDOCRINE TEDX - Potential Endocrine Disruptors Potential Endocrine Disruptor


CANCER MAK Carcinogen Group 4 - Non-genotoxic carcinogen with low risk under MAK/BAT levels

SKIN SENSITIZE MAK Sensitizing Substance Sh - Danger of skin sensitization




SUBSTANCE NOTES:

ADHESIVE %: 4.1000 HPD URL:Inventory Threshold: 100 ppm Residuals Considered: YesMaterial Notes: No Residuals/Impurities are known or expected to be present at or above the Inventory Threshold listed, based on Supplier Disclosure Letter.

UNDISCLOSED

%: 80.0000 - 90.0000 GS: LT-UNK RC: None NANO: NO ROLE: Polymer




UNDISCLOSED

%: 10.0000 - 15.0000 GS: LT-UNK RC: None NANO: NO ROLE: Plasticizer




WATER ID: 7732-18-5

%: 1.0000 - 5.0000 GS: BM-4 RC: None NANO: NO ROLE: Diluent



SUBSTANCE NOTES:

UNDISCLOSED

%: 0.1000 - 0.5000 GS: LT-1 RC: None NANO: NO ROLE: Raw Material




CANCER EU - R-phrases R45 - May cause cancer


CANCER EU - REACH Annex XVII CMRs Carcinogen Category 2 - Substances which should be regarded as if they are Carcinogenic to man





UNDISCLOSED

%: 0.0100 - 0.0500 GS: LT-UNK RC: None NANO: NO ROLE: Raw Material







CERTIFYING PARTY: Third PartyAPPLICABLE FACILITIES: City of Industry, CA; Pittsburg, CA; Denver, CO; Forth Worth, TXCERTIFICATE URL: www.cemcosteel.com/sites/default/files/CEMCOs%20Environmental%20Product%20Declaration_EPD.pdfCERTIFICATION AND COMPLIANCE NOTES: Declaration number: 4787356941.101.1. Environmental Product Declaration covers the following CEMCO Cold-Formed Steel Framing Systems, including: Structural Stud and Track (ICC-ES ESR 3016); ViperStud Interior Framing (ICC-ES ESR 2620 & ATI-ES 0154); ProX Header (IAPMO ER-0286); SureBoard for Shear panels (IAPMO ER-0126); Sure-Span Floor Joist Framing System (ESR PENDING); CST, SLP-TRK, and FAS Track 1000 Brand Slotted Tracks (ICC-ES ESR 2012); USG SHAFTWALL Brand CH and H-Stud Studs and Track (AER 09038); Expanded Metal Lath Products (ICC-ES ESR 1623); Plastering Accessories (ICC-ES ESR 1623); Drywall/Interior Accessories (ICC-ES ESR 3016); Connectors, Clips, and Channels (ICC-ES ESR 3016).




OTHER UES Evaluation Report (ER-0126)



CERTIFYING PARTY: Third PartyAPPLICABLE FACILITIES: City of Industry, CA 91746; Pittsburg, CA 94565; Denver, CO 80204; Fort Worth, TX 76140CERTIFICATE URL: http://www.iapmoes.org/Documents/ER_0126.pdfCERTIFICATION AND COMPLIANCE NOTES: IAPMO ER-0126. Scope of Evaluation includes compliance to the following codes & regulations: 2015, 2012, and 2009 International Building Code® (IBC); 2015, 2012, and 2009 International Residential Code® (IRC); 2016 and 2013 California Building Code® (CBC). Evaluated in accordance with EC 003-2016. Properties assessed: Structural.






FASTENERS HPD URL: No HPD availableCONDITION WHEN RECOMMENDED OR REQUIRED AND/OR OTHER NOTES: Used to attach Sure-Board® Structural Panels to Framing. See IAPMO ER-0126 report for specific fastener requirements: http://www.iapmoes.org/Documents/ER_0126.pdf






MANUFACTURER: CEMCO

ADDRESS: 13191 Crossroads Pkwy. North City of Industry, CA 91746 USA




PHONE: 800.416.2278


KEY










The Health Product Declaration (HPD) Open Standard provides for the disclosure of product contents and potential associated human and environmental health hazards. Hazard associations are based on the HPD Priority Hazard Lists, the GreenScreen List Translator, and when available, full GreenScreen assessments. The HPD Open Standard does not provide an assessment of health impacts throughout the product life cycle. It does not provide an assessment of exposure or risk associated with product handling or use. It also does not address potential health impacts of: (i) substances used or created during the manufacturing process unless they remain in the final product, or (ii) substances created after the product is delivered for end use (e.g., if the product burns, degrades, or otherwise changes chemical composition).


A disclosure completed in compliance with the HPD Open Standard is referred to as a “Health Product Declaration,” or “HPD.” The product manufacturer and any applicable independent verifier are solely responsible for the accuracy of statements and claims made in this HPD and for compliance with the HPD Open Standard noted.



Metal Lath by CEMCO

Health ProductDeclaration v2.1

CLASSIFICATION: 09 22 36.23 Metal Lath created via: HPDC Online Builder

PRODUCT DESCRIPTION: This HPD covers all CEMCO Metal Lath products without paper backing, including Expanded, Self-Furred, CEM-

MESH, Flat-Ribbed, and Hi-Ribbed Metal Lath. All CEMCO Metal Lath products are produced from standard G60 hot-dipped galvanized steel,

and meet or exceed industry standards. CEMCO's Metal Lath products are certified code compliant via ICC-ES ESR-1623.

Section 1: Summary Nested Method / Material Threshold

CONTENT INVENTORY


Summary of product contents and results from screening individual chemical substances

against HPD Priority Hazard Lists and the GreenScreen for Safer Chemicals®. The HPD

does not assess whether using or handling this product will expose individuals to its

chemical substances or any health risk. Refer to Section 2 for further details.

MATERIAL | SUBSTANCE | RESIDUAL OR IMPURITY

GREENSCREEN SCORE | HAZARD TYPE

HOT-DIPPED GALVANIZED STEEL (G60) [ STEEL (STEEL) NoGS ZINC (ZINC) LT-P1 |

AQU | END | MUL | PHY ]

Number of Greenscreen BM-4/BM3 contents.......... 0

Contents highest concern GreenScreen

Benchmark or List translator Score.............. LT-P1

Nanomaterial............. No


This Health Product Declaration (HPD) was completed in accordance with the HPD

Standard version 2.1, and discloses hazards associated with all substances present at or

above 1000 parts per million (ppm) in the finished product. Therefore, this HPD is

consistent with the LEED v4 MR credit Building Product Disclosure and Optimization:

Material Ingredient Reporting (Option 1).

Inventory Reporting Format

Nested Materials Method

Basic Method

Threshold Disclosed Per

Material

Product

Threshold level

100 ppm

1,000 ppm

Per GHS SDS

Per OSHA MSDS

Other

Residuals/Impurities


Considered in 1 of 1

Materials

Explanation(s) provided

for Residuals/Impurities?

Yes No

Yes No

Yes No

Yes No

Are All Substances Above the Threshold Indicated:

Characterized

Percent Weight and Role Provided?

Screened

Using Priority Hazard Lists with Results

Disclosed?

Identified

Name and Identifier Provided?



CERTIFICATIONS AND COMPLIANCE See Section 3 for additional listings.

Multi-attribute: Environmental Product Declaration (EPD) by UL

Other: ICC-ES Evaluation Report (ESR-1623)

CONSISTENCY WITH OTHER PROGRAMS

Pre-checked for LEED v4 Material Ingredients, Option 1

Third Party Verified?

Yes

No

PREPARER: Self-Prepared

VERIFIER:

VERIFICATION #:

SCREENING DATE: 2017-08-01

PUBLISHED DATE: 2017-08-10


Metal Lath

www.hpd-collaborative.org HPD v2.1 created via HPDC Builder Page 1 of 4



This section lists contents in a product based on specific threshold(s) and reports detailed health information including hazards. This HPD uses the inventory method indicated above, which is

one of three possible methods:

Basic Inventory method with Product-level threshold.

Nested Material Inventory method with Product-level threshold

Nested Material Inventory method with individual Material-level thresholds

Definitions and requirements for the three inventory methods and requirements for each data field can be found in the HPD Open Standard version 2.1, available on the HPDC website at:

www.hpd-collaborative.org/hpd-2-1-standard

HOT-DIPPED GALVANIZED STEEL (G60) %: 100.0000 - 100.0000 HPD URL:

MATERIAL THRESHOLD: 1000 ppm RESIDUALS AND IMPURITIES CONSIDERED: Yes

RESIDUALS AND IMPURITIES NOTES: No residuals or impurities are known or expected to be present in this material above the inventory threshold

indicated, based on supplier SDS and as predicted by process chemistry (Pharos CML).

OTHER MATERIAL NOTES: Specific guidelines are being created to address known issues related to transparency and disclosure for several materials

(“Special Conditions”), including Metal Alloys such as Steel. This HPD will be updated as appropriate when the guidelines for Steel are released.

Passivation coatings for corrosion resistance are an industry standard for this type of material; however, the substances used for such coatings fall

below the inventory threshold (0.1% or 1000 ppm) of the material, and are therefore not reported here.

STEEL (STEEL) ID: 12597-69-2

%: 97.4000 - 98.7000 GS: NoGS RC: Both NANO: No ROLE: Base Metal



SUBSTANCE NOTES: CEMCO cold-formed steel framing products contain 30% to 37% pre- and post-consumer recycled steel sourced from several domestic (USA)

suppliers. This substance is considered essentially inert for the purposes of Pharos toxics scoring (Pharos CML).

ZINC (ZINC) ID: 7440-66-6

%: 1.3000 - 2.6000 GS: LT-P1 RC: None NANO: No ROLE: Metallic Coating







PHYSICAL HAZARD (REACTIVE) EU - GHS (H-Statements) H250 - Catches fire spontaneously if exposed to air

PHYSICAL HAZARD (REACTIVE) EU - GHS (H-Statements) H260 - In contact with water releases flammable gases which may ignite

spontaneously

SUBSTANCE NOTES: Form-specific hazards not expected to apply to the finished and installed product. However, further processing (e.g. welding, sawing, etc) during

installation may release fumes or other respirable particles. The Safety Data Sheet (SDS) for Galvanized Sheet Steel can be found at http://cemcosteel.com/cemco-

specifications.


Metal Lath



This section lists applicable certification and standards compliance information for VOC emissions and VOC content. Other types of health or

environmental performance testing or certifications completed for the product may be provided.

MULTI-ATTRIBUTE Environmental Product

Declaration (EPD) by UL

CERTIFYING PARTY: Third Party

APPLICABLE FACILITIES: City of Industry, CA; Pittsburg, CA; Denver, CO; Forth Worth, TX

CERTIFICATE URL:

http://www.cemcosteel.com/sites/default/files/CEMCOs%20Environmental%20Product%20Declaration_EPD.pdf

ISSUE

DATE:2016-

07-13

EXPIRY

DATE:

2021-

07-13

CERTIFIER OR

LAB: UL

Environment

CERTIFICATION AND COMPLIANCE NOTES: Declaration number: 4787356941.101.1. Environmental Product Declaration covers the following

CEMCO Cold-Formed Steel Framing Systems, including: Structural Stud and Track (ICC-ES ESR 3016); ViperStud Interior Framing (ICC-

ES ESR 2620); ProX Header (IAPMO ER-0286); SureBoard for Shear panels (IAPMO ER-0126); Sure-Span Floor Joist Framing System

(ESR PENDING); CST/SLP-TRK, and FAS Track 1000 Brand Slotted Tracks (ICC-ES ESR 2012); USG SHAFTWALL Brand CH and H-

Stud Studs and Track (AER 09038); Expanded Metal Lath Products (ICC-ES ESR 1623); Plastering Accessories (ICC-ES ESR 1623);

Drywall/Interior Accessories (ICC-ES ESR 3016); Connectors, Clips, and Channels (ICC-ES ESR 3016).

OTHER ICC-ES Evaluation Report (ESR-1623)

CERTIFYING PARTY: Self-declared

APPLICABLE FACILITIES: All

CERTIFICATE URL: http://www.icc-es.org/reports/pdf_files/ICC-

ES/ESR-1623.pdf

ISSUE DATE:2015-05-01 EXPIRY DATE: 2019-05-01 CERTIFIER OR LAB: ICC Evaluation

Services

CERTIFICATION AND COMPLIANCE NOTES: EVALUATION SUBJECT: CEMCO METAL LATH PRODUCTS. EVALUATION SCOPE: Compliance

with the following codes: 2012, 2009 and 2006 International Building Code®; 2012, 2009 and 2006 International Residential Code®; 2013

Abu Dhabi International Building Code (ADIBC). Property evaluated: Physical properties. Products include: CEMCO 2.5 Expanded

Diamond Mesh Metal Lath; CEMCO 2.5 Self-Furred Expanded Diamond Mesh Metal Lath; CEMCO 3.4 Expanded Diamond Mesh Metal

Lath; CEMCO 3.4 Self-Furred Expanded Diamond Mesh Metal Lath; 1/8-inch Self- Furred Flat Rib Lath; 3/8-inch 3.4 Hi Rib Lath.


This section lists related products or materials that the manufacturer requires or recommends for installation (such as adhesives or fasteners),

maintenance, cleaning, or operations. For information relating to the contents of these related products, refer to their applicable Health Product

Declarations, if available.

No accessories are required for this product.




MANUFACTURER: CEMCO

ADDRESS: 13191 Crossroads Pkwy. North

Suite 325



PHONE: 800.416.2278

Metal Lath



City of Industry CA 91746, USA



KEY

OSHA MSDS Occupational Safety and Health Administration Material Safety Data Sheet

GHS SDS Globally Harmonized System of Classi cation and Labeling of Chemicals Safety Data Sheet

Hazard Types

AQU Aquatic toxicity

CAN Cancer

DEV Developmental toxicity

END Endocrine activity

EYE Eye irritation/corrosivity

GEN Gene mutation

GLO Global warming

MAM Mammalian/systemic/organ toxicity

MUL Multiple hazards

NEU Neurotoxicity

OZO Ozone depletion

PBT Persistent Bioaccumulative Toxic

PHY Physical Hazard (reactive)

REP Reproductive toxicity

RES Respiratory sensitization

SKI Skin sensitization/irritation/corrosivity

LAN Land Toxicity

NF Not found on Priority Hazard Lists

GreenScreen (GS)

BM-4 Benchmark 4 (prefer-safer chemical)

BM-3 Benchmark 3 (use but still opportunity for improvement)

BM-2 Benchmark 2 (use but search for safer substitutes)

BM-1 Benchmark 1 (avoid - chemical of high concern)

BM-U Benchmark Unspeci ed (insu cient data to benchmark)

LT-P1 List Translator Possible Benchmark 1

LT-1 List Translator Likely Benchmark 1

LT-UNK List Translator Benchmark Unknown (insufficient information

from List Translator lists to benchmark)

NoGS Unknown (no data on List Translator Lists)

Recycled Types

PreC Preconsumer (Post-Industrial)

PostC Postconsumer

Both Both Preconsumer and Postconsumer

Unk Inclusion of recycled content is unknown

None Does not include recycled content

Other Terms

Inventory Methods:

Nested Method / Material Threshold Substances listed within each material per threshold indicated per material

Nested Method / Product Threshold Substances listed within each material per threshold indicated per product

Basic Method / Product Threshold Substances listed individually per threshold indicated per produc

Nano Composed of nano scale particles or nanotechnology

Third Party Verified Verification by independent certifier approved by HPDC

Preparer Third party preparer, if not self-prepared by manufacturer

Applicable facilities Manufacturing sites to which testing applies

The Health Product Declaration (HPD) Open Standard provides for the disclosure of product contents and potential associated human and environmental health hazards.

Hazard associations are based on the HPD Priority Hazard Lists, the GreenScreen List Translator™, and when available, full GreenScreen® assessments. The HPD Open

Standard v2.1 is not:

a method for the assessment of exposure or risk associated with product handling or use,

a method for assessing potential health impacts of: (i) substances used or created during the manufacturing process or (ii) substances created after the product is

delivered for end use.

Information about life cycle, exposure and/or risk assessments performed on the product may be reported by the manufacturer in appropriate Notes sections, and/or, where

applicable, in the Certifications section.

The HPD Open Standard was created and is supported by the Health Product Declaration Collaborative (the HPD Collaborative), a customer-led organization composed of

stakeholders throughout the building industry that is committed to the continuous improvement of building products through transparency, openness, and innovation

throughout the product supply chain.

The product manufacturer and any applicable independent verifier are solely responsible for the accuracy of statements and claims made in this HPD and for compliance

with the HPD standard noted.

Metal Lath



Metal Lath with D-Paper by CEMCO



PRODUCT DESCRIPTION: This HPD covers CEMCO Metal Lath products with D-Paper, including Diamond Products (1.75, 2.5, and 3.4; Flat,

Dimpled, and Grooved), and 1/8" Flat Rib Products (1/8" Riblath). All CEMCO Metal Lath products are produced from standard G60 hot-dipped

galvanized steel, and meet or exceed industry standards. CEMCO's Metal Lath products are certified code compliant via ICC-ES ESR-1623.

Section 1: Summary Nested Method / Product Threshold

CONTENT INVENTORY









AQU | END | MUL | PHY ] D-PAPER [ CELLULOSE PULP (CELLULOSE PULP) NoGS

ASPHALT (ASPHALT) LT-1 | CAN UNDISCLOSED LT-1 | CAN | END UNDISCLOSED

LT-UNK | CAN ] HOT MELT ADHESIVE [ UNDISCLOSED LT-UNK UNDISCLOSED LT-1 |

CAN PARAFFIN (PARAFFIN) LT-UNK UNDISCLOSED LT-UNK ]



Benchmark or List translator Score.............. LT-1




Standard version 2.1, and discloses hazards associated with all known substances present

at or above 1000 parts per million (ppm) in the finished product. Therefore, this HPD is





Basic Method


Material

Product

Threshold level

100 ppm

1,000 ppm

Per GHS SDS

Per OSHA MSDS

Other




Materials



Yes No

Yes No

Yes No

Yes No


Characterized


Screened


Disclosed?

Identified










Yes

No


VERIFIER:

VERIFICATION #:




Metal Lath with D-Paper












PRODUCT THRESHOLD: 1000 ppm RESIDUALS AND IMPURITIES CONSIDERED: Yes

RESIDUALS AND IMPURITIES NOTES: No residuals or impurities are known or expected to be present from this material above the inventory threshold

indicated for the finished product that return a GS score of BM-1, LT-1 or LT-P1, based on information provided in supplier SDS and as predicted

by process chemistry (Pharos CML).





















spontaneously



specifications.

D-PAPER %: 28.1000 - 42.3000 HPD URL:





RESIDUALS AND IMPURITIES NOTES: No residuals or impurities are known or expected to be present in this material above the inventory threshold indicated

for the product that return a GS score of BM-1, LT-1 or LT-P1, based on information provided in supplier SDS and as predicted by process

chemistry (Pharos CML).

OTHER MATERIAL NOTES: Asphalt saturated "D-Paper" attached to metal lath using Hot Melt Adhesive.

CELLULOSE PULP (CELLULOSE PULP) ID: 65996-61-4

%: 50.0000 - 75.0000 GS: NoGS RC: None NANO: No ROLE: Liner Paper Substrate



SUBSTANCE NOTES: This substance is considered essentially inert for the purposes of Pharos toxics scoring.

ASPHALT (ASPHALT) ID: 8052-42-4

%: 25.0000 - 50.0000 GS: LT-1 RC: None NANO: No ROLE: Liner Paper Reinforcement


CANCER IARC Group 2b - Possibly carcinogenic to humans


CANCER MAK Carcinogen Group 2 - Considered to be carcinogenic for man

SUBSTANCE NOTES: Pharos CML lists all Known or Potential Residuals at less than 0.01%.

UNDISCLOSED

%: 0.5000 - 1.0000 GS: LT-1 RC: None NANO: No ROLE: Pigment; Filler



CANCER CA EPA - Prop 65 Carcinogen - specific to chemical form or exposure route

CANCER IARC Group 2B - Possibly carcinogenic to humans - inhaled from occupational

sources


CANCER MAK Carcinogen Group 3A - Evidence of carcinogenic effects but not sufficient

to establish MAK/BAT value

SUBSTANCE NOTES: Identified on the US EPA Safer Chemical Ingredient List. Warnings are restricted to respirable forms of this substance, and thus are not expected to

apply when bound in the matrix of the finished product. Supplier has shared substance name and CASRN under the terms of a non-disclosure agreement; substance to

remain proprietary to supplier. Substance has been screened against HPD Priority Lists with results disclosed.

UNDISCLOSED

%: 0.1000 - 0.2000 GS: LT-UNK RC: None NANO: No ROLE: Filler


CANCER MAK Carcinogen Group 3B - Evidence of carcinogenic effects but not sufficient




for classification

SUBSTANCE NOTES: Identified on the US EPA Safer Chemical Ingredient List. Supplier has shared substance name and CASRN under the terms of a non-disclosure

agreement; substance to remain proprietary to supplier. Substance has been screened against HPD Priority Lists with results disclosed.

HOT MELT ADHESIVE %: 4.3000 - 6.5000 HPD URL:





OTHER MATERIAL NOTES: Hot Melt Adhesive used to attach D-Paper to metal lath.

UNDISCLOSED

%: 40.0000 - 45.0000 GS: LT-UNK RC: None NANO: No ROLE: Adhesive Binder



SUBSTANCE NOTES: Supplier has shared substance name and CASRN under the terms of a non-disclosure agreement; substance to remain proprietary to supplier.

Substance has been screened against HPD Priority Lists with results disclosed.

UNDISCLOSED

%: 39.5000 - 44.5000 GS: LT-1 RC: None NANO: No ROLE: Adhesive Modifier





SUBSTANCE NOTES: Supplier has shared substance name and CASRN under the terms of a non-disclosure agreement; substance to remain proprietary to supplier.

Substance has been screened against HPD Priority Lists with results disclosed. May also include another undisclosed CASRN (NoGS; No warnings found on HPD

Priority lists).

PARAFFIN (PARAFFIN) ID: 8002-74-2

%: 15.0000 - 20.0000 GS: LT-UNK RC: None NANO: No ROLE: Adhesive Wax



SUBSTANCE NOTES:

UNDISCLOSED

%: 0.5000 - 0.5000 GS: LT-UNK RC: None NANO: No ROLE: Antioxidant






SUBSTANCE NOTES: Identified on the US EPA Safer Chemical Ingredient List. Supplier has shared substance name and CASRN under the terms of a non-disclosure

agreement; substance to remain proprietary to supplier. Substance has been screened against HPD Priority Lists with results disclosed. This substance falls below the

declared Inventory Threshold for the product.








CERTIFICATE URL:


ISSUE

DATE:2016-

07-13

EXPIRY

DATE:

2021-

07-13

CERTIFIER OR

LAB: UL

Environment





Stud Studs and Track (AER 09038); Expanded Metal Lath Products (ICC-ES ESR 1623); Plastering Accessories (ICC- ES ESR 1623);






ES/ESR-1623.pdf


Services

















MANUFACTURER: CEMCO


Suite 325





PHONE: 800.416.2278


KEY



Hazard Types


CAN Cancer




GEN Gene mutation

GLO Global warming



NEU Neurotoxicity

OZO Ozone depletion






LAN Land Toxicity


GreenScreen (GS)











Recycled Types


PostC Postconsumer




Other Terms

Inventory Methods:



















MANUFACTURER: CEMCO


Suite 325





PHONE: 800.416.2278


KEY



Hazard Types


CAN Cancer




GEN Gene mutation

GLO Global warming



NEU Neurotoxicity

OZO Ozone depletion






LAN Land Toxicity


GreenScreen (GS)











Recycled Types


PostC Postconsumer




Other Terms

Inventory Methods:




























MANUFACTURER: CEMCO


Suite 325





PHONE: 800.416.2278


KEY



Hazard Types


CAN Cancer




GEN Gene mutation

GLO Global warming



NEU Neurotoxicity

OZO Ozone depletion






LAN Land Toxicity


GreenScreen (GS)











Recycled Types


PostC Postconsumer




Other Terms

Inventory Methods:


























Metal Lath with K-Paper by CEMCO



PRODUCT DESCRIPTION: This HPD covers CEMCO Metal Lath products with K-Paper, including 1/8" CEM-MESH Flat Rib Metal Lath, and

3/8" Hi-Rib Metal Lath. CEMCO’s CEM-MESH Flat-Rib with K-Paper is a more rigid lath with 1/8" longitudinal ribs spaced at 3" on-center that

provide for wider spacing between wooden or metal supports. Backed with 2 strips of K-Paper, this lath is ideal for machine applied plaster.

CEMCO’s 3/8" Hi-Rib Metal Lath is the most rigid of all metal laths. With full 3/8" ribs longitudinally spaced at 4" apart, and a 1/8" rib between

them, Hi-Rib lath is able to span up to 24" on center. The 3" strips of K-Paper attached to the spaces between the 3/8" ribs minimize blow

through of plaster when machine applied. This lath can be used in both vertical and horizontal applications. All CEMCO Metal Lath products are

produced from standard G60 hot-dipped galvanized steel, and meet or exceed industry standards. CEMCO's Metal Lath products are certified

code compliant via ICC-ES ESR-1623.


CONTENT INVENTORY









AQU | END | MUL | PHY ] NATURAL KRAFT PAPER [ KRAFT PAPER (KRAFT PAPER)

NoGS ] HOT-MELT ADHESIVE [ ETHYLENE VINYL ACETATE POLYMER (EVA)

(ETHYLENE VINYL ACETATE POLYMER (EVA)) LT-UNK PETROLEUM RESINS

(PETROLEUM RESINS) LT-1 | CAN PENTAERYTHRITOL ROSINATE

(PENTAERYTHRITOL ROSINATE) LT-UNK POLYETHYLENE (POLYETHYLENE) LT-UNK

]



Benchmark or List translator Score.............. LT-1




Standard version 2.1, and discloses hazards associated with all known substances present

at or above 1000 parts per million (ppm) in the finished product. Therefore, this HPD is





Basic Method


Material

Product

Threshold level

100 ppm

1,000 ppm

Per GHS SDS

Per OSHA MSDS

Other




Materials



Yes No

Yes No

Yes No

Yes No


Characterized


Screened


Disclosed?

Identified










Yes

No


VERIFIER:

VERIFICATION #:




Metal Lath with K-Paper




































spontaneously



specifications.

NATURAL KRAFT PAPER %: 8.6000 - 9.3000 HPD URL:








OTHER MATERIAL NOTES: Two strips of "K-Paper" attached to metal lath using Hot-Melt Adhesive.

KRAFT PAPER (KRAFT PAPER) ID: Not registered

%: 100.0000 - 100.0000 GS: NoGS RC: None NANO: No ROLE: Liner Paper: Substrate



SUBSTANCE NOTES: This substance is considered essentially inert for the purposes of Pharos toxics scoring (Pharos CML). This substance does not currently have an

assigned CAS number, and thus is not considered to be "Identified" on this HPD.

HOT-MELT ADHESIVE %: 2.1000 - 2.3000 HPD URL:





OTHER MATERIAL NOTES: Hot-Melt Adhesive used to attach K-Paper to metal lath. Percent of substances given as ranges in order to protect the

proprietary nature of supplier's formulation.

ETHYLENE VINYL ACETATE POLYMER (EVA) (ETHYLENE VINYL ACETATE POLYMER

(EVA))

ID: 24937-78-8

%: 35.0000 - 40.0000 GS: LT-UNK RC: None NANO: No ROLE: Hot Melt Adhesive



SUBSTANCE NOTES:

PETROLEUM RESINS (PETROLEUM RESINS) ID: 64742-16-1

%: 30.0000 - 35.0000 GS: LT-1 RC: None NANO: No ROLE: Modifier





SUBSTANCE NOTES:

PENTAERYTHRITOL ROSINATE (PENTAERYTHRITOL ROSINATE) ID: 8050-26-8

%: 15.0000 - 20.0000 GS: LT-UNK RC: None NANO: No ROLE: Modifier






SUBSTANCE NOTES:

POLYETHYLENE (POLYETHYLENE) ID: 9002-88-4

%: 10.0000 - 15.0000 GS: LT-UNK RC: None NANO: No ROLE: Raw Material



SUBSTANCE NOTES:








CERTIFICATE URL:


ISSUE

DATE:2016-

07-13

EXPIRY

DATE:

2021-

07-13

CERTIFIER OR

LAB: UL

Environment





Stud Studs and Track (AER 09038); Expanded Metal Lath Products (ICC-ES ESR 1623); Plastering Accessories (ICC- ES ESR 1623);






ES/ESR-1623.pdf


Services

















MANUFACTURER: CEMCO


Suite 325





PHONE: 800.416.2278


KEY



Hazard Types


CAN Cancer




GEN Gene mutation

GLO Global warming



NEU Neurotoxicity

OZO Ozone depletion






LAN Land Toxicity


GreenScreen (GS)











Recycled Types


PostC Postconsumer




Other Terms

Inventory Methods:











Steel Framing Components for USG Shaft Wall Systems by CEMCO


CLASSIFICATION: 09 22 16 Finishes: Non-Structural Metal Framing created via: HPDC Online Builder

PRODUCT DESCRIPTION: USG, in partnership with CEMCO, presents the construction industry’s best performing shaftwall, fire wall, and party

wall components. USG Shaft Wall Systems are non-loadbearing gypsum wall partition assemblies constructed from outside the shaft at each

floor. CEMCO is the licensed manufacturer of the metal framing components for the USG Shaft Wall Systems, which include the C-H Stud, J-

Runner, Jamb-Strut, and E-Stud. “C-H” Shaft Wall Studs (18 mil, 34 mil) are fabricated in web depths of 2-1/2", 4", and 6" each with a short-

flange width of 1-3/8" and long-flange width of 1-1/2". “JR” J-Runners (23 mil, 34 mil) are fabricated in web depths of 2-1/2", 4", and 6" with a

short leg of 1", and a long leg of 2". Jamb-Strut members (20 mil, 34 mil) are fabricated with stud member depths of 2-1/2", 4", and 6" with a short

leg of 1", and a long leg of 2". E-Studs (18 mil, 34 mil) are fabricated in web depths of 2-1/2", 4" and 6", each with a short flange of 3/4" and a

long flange of 1". All steel framing components for USG Shaft Wall System manufactured by CEMCO are produced from hot-dipped galvanized

steel in standard G40 coating. G60 is available upon special request.


CONTENT INVENTORY

















above 1000 parts per million (ppm) in the finished product, along with the role and percent

weight. Therefore, this HPD is consistent with the LEED v4 MR credit Building Product

Disclosure and Optimization: Material Ingredient Reporting (Option 1).



Basic Method


Material

Product

Threshold level

100 ppm

1,000 ppm

Per GHS SDS

Per OSHA MSDS

Other




Materials



Yes No

Yes No

Yes No

Yes No


Characterized


Screened


Disclosed?

Identified









Yes

No


VERIFIER:

VERIFICATION #:




Steel Framing Components for USG Shaft Wall Systems













RESIDUALS AND IMPURITIES NOTES: No residuals or impurities are known or expected to be present at or above the Content Inventory Threshold indicated

that have a GS score of BM-1, LT-1 or LT-P1 based on supplier SDS and as predicted by process chemistry (Pharos CML).


(“Special Conditions”), including Metal Alloys such as steel. This HPD will be updated as appropriate when the guidelines for Steel are released.



















spontaneously



specifications.











CERTIFICATE URL:


ISSUE

DATE:2016-

07-13

EXPIRY

DATE:

2021-

07-13

CERTIFIER OR

LAB: UL

Environment

CERTIFICATION AND COMPLIANCE NOTES: Declaration number: 4787356941.101.1. Type III Environmental Product Declaration covers the

following CEMCO Cold-Formed Steel Framing Systems, including: Structural Stud and Track (ICC-ES ESR 3016); ViperStud® Interior

Framing (ICC-ES ESR 2620); ProX Header® (IAPMO ER-0286); SureBoard® for Shear panels (IAPMO ER- 0126); Sure-Span® Floor

Joist Framing System (ESR PENDING); CST/SLP-TRK®, and FAS Track® 1000 Brand Slotted Tracks (ICC-ES ESR 2012); USG

SHAFTWALL Brand CH and H-Stud Studs and Track (AER 09038); Expanded Metal Lath Products (ICC-ES ESR 1623); Plastering

Accessories (ICC-ES ESR 1623); Drywall/Interior Accessories (ICC-ES ESR 3016); Connectors, Clips, and Channels (ICC-ES ESR 3016).





SHEETROCK® BRAND GYPSUM PANELS HPD URL: https://www.hpd-collaborative.org/hpd-public-repository/

CONDITION WHEN RECOMMENDED OR REQUIRED AND/OR OTHER NOTES:

Installation of USG Shaft Wall Systems. The assemblies are constructed of gypsum liner panels friction-fitted into C-H studs in a progressive manner,

with gypsum panels, gypsum fiber panels or cement board applied to the face.

DUROCK® CEMENT BOARD HPD URL: https://www.hpd-collaborative.org/hpd-public-repository/


Installation of USG Shaft Wall Systems. The assemblies are constructed of gypsum liner panels friction-fitted into C-H studs in a progressive manner,

with gypsum panels, gypsum fiber panels or cement board applied to the face.

SHEETROCK® BRAND INTERIOR FINISHING PRODUCTS HPD URL: No HPD available


Finish all face layer joints and internal angles with a Sheetrock® interior finishing system installed according to manufacturer’s directions.




MANUFACTURER: CEMCO CONTACT NAME: Fernando Sesma





Suite 325




PHONE: 800.416.2278


KEY



Hazard Types


CAN Cancer




GEN Gene mutation

GLO Global warming



NEU Neurotoxicity

OZO Ozone depletion






LAN Land Toxicity


GreenScreen (GS)











Recycled Types


PostC Postconsumer




Other Terms

Inventory Methods:
























Steel Framing Components for USG Area Separation Wall Systems by CEMCO


CLASSIFICATION: 09 22 16 Finishes: Non-Structural Metal Framing created via: HPDC Online Builder

PRODUCT DESCRIPTION: USG, in partnership with CEMCO, presents the construction industry’s best performing shaftwall, fire wall, and party

wall components. USG Area Separation Wall Systems are lightweight, non-loadbearing gypsum panel partition assemblies used to provide fire-

resistive protection for common walls in townhouse construction. Area separation walls are designed to allow for collapse of the construction on

the fire-exposed side, without collapse of the entire wall, thus protecting the adjacent townhouse. CEMCO is the licensed manufacturer of the

metal framing components for the USG Area Separation Wall Systems, which include the C-Runner, H-Stud, and Aluminum Breakaway Clip. C-

Runners (18 mil, 24 mil) are fabricated with a width of 2", legs of 1", and length of 10'. "H" Shaft Wall Studs (18 mil, 34 mil) are fabricated with a

width of 2", depth of 1-3/8", and length of 8' to 16'. All steel framing components for USG Shaft Wall System manufactured by CEMCO are

produced from hot-dipped galvanized steel in standard G40 coating. G60 is available upon special request. This HPD covers steel framing

components only.


CONTENT INVENTORY

















above 1000 parts per million (ppm) in the finished product, along with the role and percent

weight. Therefore, this HPD is consistent with the LEED v4 MR credit Building Product

Disclosure and Optimization: Material Ingredient Reporting (Option 1).



Basic Method


Material

Product

Threshold level

100 ppm

1,000 ppm

Per GHS SDS

Per OSHA MSDS

Other




Materials



Yes No

Yes No

Yes No

Yes No


Characterized


Screened


Disclosed?

Identified









Yes

No


VERIFIER:

VERIFICATION #:




Steel Framing Components for USG Area Separation Wall Systems













RESIDUALS AND IMPURITIES NOTES: No residuals or impurities are known or expected to be present at or above the Content Inventory Threshold indicated

that have a GS score of BM-1, LT-1 or LT-P1 based on supplier SDS and as predicted by process chemistry (Pharos CML).


(“Special Conditions”), including Metal Alloys such as steel. This HPD will be updated as appropriate when the guidelines for Steel are released.



















spontaneously



specifications.











CERTIFICATE URL:


ISSUE

DATE:2016-

07-13

EXPIRY

DATE:

2021-

07-13

CERTIFIER OR

LAB: UL

Environment

CERTIFICATION AND COMPLIANCE NOTES: Declaration number: 4787356941.101.1. Type III Environmental Product Declaration covers the

following CEMCO Cold-Formed Steel Framing Systems, including: Structural Stud and Track (ICC-ES ESR 3016); ViperStud® Interior

Framing (ICC-ES ESR 2620); ProX Header® (IAPMO ER-0286); SureBoard® for Shear panels (IAPMO ER- 0126); Sure-Span® Floor

Joist Framing System (ESR PENDING); CST/SLP-TRK®, and FAS Track® 1000 Brand Slotted Tracks (ICC-ES ESR 2012); USG

SHAFTWALL Brand CH and H-Stud Studs and Track (AER 09038); Expanded Metal Lath Products (ICC-ES ESR 1623); Plastering

Accessories (ICC-ES ESR 1623); Drywall/Interior Accessories (ICC-ES ESR 3016); Connectors, Clips, and Channels (ICC-ES ESR 3016).





SHEETROCK® BRAND GYPSUM PANELS HPD URL: https://www.hpd-collaborative.org/hpd-public-repository/


Installation of USG Area Separation Wall Systems.

ALUMINUM BREAKAWAY CLIP BY CEMCO HPD URL: https://www.hpd-collaborative.org/hpd-public-repository/


Installation of USG Area Separation Wall Systems. Aluminum Breakaway Clips attach the separation wall to the adjacent framing. When one side of

the separation wall is exposed to fire, the clips are designed to soften and break away. This allows the structure on the fire side of the separation wall

to collapse, while the clips on the unexposed side of the separation wall continue to support the separation wall.

SHEETROCK® ACOUSTICAL SEALANT HPD URL: No HPD available


Installation of USG Area Separation Wall Systems.

SHEETROCK® BRAND INTERIOR FINISHING PRODUCTS HPD URL: No HPD available


Finish all face layer joints and internal angles with a Sheetrock® interior finishing system installed according to manufacturer’s directions.







MANUFACTURER: CEMCO


Suite 325





PHONE: 800.416.2278


KEY



Hazard Types


CAN Cancer




GEN Gene mutation

GLO Global warming



NEU Neurotoxicity

OZO Ozone depletion






LAN Land Toxicity


GreenScreen (GS)











Recycled Types


PostC Postconsumer




Other Terms

Inventory Methods:























MANUFACTURER: CEMCO


Suite 325





PHONE: 800.416.2278


KEY



Hazard Types


CAN Cancer




GEN Gene mutation

GLO Global warming



NEU Neurotoxicity

OZO Ozone depletion






LAN Land Toxicity


GreenScreen (GS)











Recycled Types


PostC Postconsumer




Other Terms

Inventory Methods:
























MANUFACTURER: CEMCO


Suite 325





PHONE: 800.416.2278


KEY



Hazard Types


CAN Cancer




GEN Gene mutation

GLO Global warming



NEU Neurotoxicity

OZO Ozone depletion






LAN Land Toxicity


GreenScreen (GS)











Recycled Types


PostC Postconsumer




Other Terms

Inventory Methods:





























Notes


Pittsburg, CA

City of Industry, CA

Denver, CO

Ft . Worth, TX

Corporate Headquarters13191 Crossroads Parkway North, Suite 325, City of Industry, CA 91746

P: 800 .775 .2362 | F: 626 .330 .7598

Southern California Manufacturing Facility263 North Covina Lane, City of Industry, CA 91746

P: 800 .775 .2362 | F: 626 .330 .7598

Northern California Manufacturing Facility1001-A Pittsburg Antioch Hwy, Pittsburg, CA 94565

P: 925 .473 .9340 | F: 925 .473 .9341

Denver Colorado Manufacturing Facility490 Osage Street, Denver, CO 80204

P: 303 .572 .3626 | F: 303 .572 .3627

Fort Worth Texas Manufacturing Facility8600 Will Rogers Blvd, Fort Worth, TX 76140

P: 817 .568 .1525 | F: 817 .568 .2759

www .cemcosteel .com

Expanding Your Solutions

Effective 9/5/2017

Pittsburg, CA

City of Industry, CA

Denver, CO

Ft. Worth, TX

LEED v4 and Sustainability Resources - cemcosteel.com v4... · LEED v4 and Sustainability Resources...

Documents

Transcript of LEED v4 and Sustainability Resources - cemcosteel.com v4... · LEED v4 and Sustainability Resources...