LED PANELS BUILDING INSTRUCTIONS · 1 Cut 4’x8’ panels into 4’x4’ squares. 2 Drill ¼”...

6
LED PANELS BUILDING INSTRUCTIONS MYREALLIFE.ORG -TREVOR GRAY- I assume no responsibility for any events that are caused by your project.

Transcript of LED PANELS BUILDING INSTRUCTIONS · 1 Cut 4’x8’ panels into 4’x4’ squares. 2 Drill ¼”...

Page 1: LED PANELS BUILDING INSTRUCTIONS · 1 Cut 4’x8’ panels into 4’x4’ squares. 2 Drill ¼” mounting holes in panels on all four sides 1’ from the corner and 2” in from the

LEDPANELSBUILDINGINSTRUCTIONS

MYREALLIFE.ORG-TREVORGRAY-

Iassumenoresponsibilityforanyeventsthatarecausedbyyourproject.

Page 2: LED PANELS BUILDING INSTRUCTIONS · 1 Cut 4’x8’ panels into 4’x4’ squares. 2 Drill ¼” mounting holes in panels on all four sides 1’ from the corner and 2” in from the

Partsneeded:

Powercord–6.78http://amzn.to/2jgdi96

12vregulatedpowersupply–19.68http://amzn.to/2jghDcF

Thermostatwire–56.24http://amzn.to/2jqHH89

LEDstripcontroller*–$20-160http://amzn.to/2jgdmFX

http://amzn.to/2j5YChK

LEDstriplight–$15.68http://amzn.to/2jyyLuU

SquarePanels**–$60-$500http://www.homedepot.com/p/Underlayment-Common-7-32-in-x-4-ft-x-8-ft-Actual-0-196-in-x-48-in-x-96-in-431178/203183010?MERCH=REC-_-SearchPLPHorizontal1_rr-_-NA-_-203183010-_-N

http://www.homedepot.com/p/Coroplast-48-in-x-96-in-x-0-157-in-White-Corrugated-Plastic-Sheet-CP4896S/205351385

http://www.regionalsupply.com/default.aspx?page=item+detail&itemcode=ALUMALITE

*forcontrolofeachstripindividually,youwillwanttomakesureyouhaveenoughchannelsonthedecoder.**thisisdependentonwhatyourdesireddurabilityis.Theyallwork,coroplastmayneedsomeweightaddedtokeepitfromswaying.

Page 3: LED PANELS BUILDING INSTRUCTIONS · 1 Cut 4’x8’ panels into 4’x4’ squares. 2 Drill ¼” mounting holes in panels on all four sides 1’ from the corner and 2” in from the

1 Cut4’x8’panelsinto4’x4’squares.

2 Drill¼”mountingholesinpanelsonallfoursides1’fromthecornerand2”infromtheedge.

3 CutLEDstripinto4’sections.

4 Placestripsonpanels.

Page 4: LED PANELS BUILDING INSTRUCTIONS · 1 Cut 4’x8’ panels into 4’x4’ squares. 2 Drill ¼” mounting holes in panels on all four sides 1’ from the corner and 2” in from the

5 Cutthermostatcabletolengthtoreachfromeachstriptodecoder.(ifyouhavetwo30channeldecoders,youwillwantthecabletoreachtothecenterpanels)

6 SolderthermostatwiretoLEDstrips.

7 MountLEDdecodertobackofpanels.Setdipswitchestoappropriateaddress.8 Attachthepanelstoeachotherwithziptiesordogchainusingtheholesyoudrilledin

step2.Havingholesoneverysideallowsyoutorotateeachpaneltogetdesiredeffect.

Page 5: LED PANELS BUILDING INSTRUCTIONS · 1 Cut 4’x8’ panels into 4’x4’ squares. 2 Drill ¼” mounting holes in panels on all four sides 1’ from the corner and 2” in from the

9 Connectwirestodecoder/Connecteitherdmxcableorrj45dependingonthedecoderyouget.

10 Mounttowhateveryoudecidetouseasastand.(i.e.truss,pipeanddrape)

Page 6: LED PANELS BUILDING INSTRUCTIONS · 1 Cut 4’x8’ panels into 4’x4’ squares. 2 Drill ¼” mounting holes in panels on all four sides 1’ from the corner and 2” in from the

11 Connectthepoweradaptertothedecoder.