LCDWIKI 3.5inch Arduino 16BIT Module MAR3513 User Manual ...€¦ · LCDWIKI 3.5inch Arduino 16BIT...

LCDWIKI 3.5inch Arduino 16BIT Module MAR3513 User Manual CR2018-MI2265

www.lcdwiki.com 1 / 21 Rev1.0

3.5inch Arduino 16BIT Module MAR3513

User Manual



Product Description

The Arduino Mega2560 module is a 3.5-inch TFT LCD module with 480x320

resolution and 65K color display. It uses 16-bit line parallel port communication, and the

driver IC is ILI9486. The module includes an LCD display, 5V ~ 3.3V level to the circuit,

can be directly plugged into the Arduino mega2560 development board, also supports SD

card and SPI Flash function expansion.

Product Features

3.5-inch color screen, support 16BIT RGB 65K color display, display rich colors

320x480 HD resolution for clear display

16-bit parallel bus transmission for fast transfer speed

On-board 5V/3.3V level-shifting IC compatible with 5V/3.3V operating voltage

Support Arduino Mage2560 for direct plug-in use

Provide Arduino libraries and rich sample programs

Support SD card and SPI Flash function extension

Military-grade process standards, long-term stable work

Provide underlying driver technical support

Product Parameters

Name Description

Display Color RGB 65K color

SKU MAR3513

Screen Size 3.5(inch)

Type TFT

Driver IC ILI9486

Resolution 480*320 (Pixel)

Module Interface 16Bit parallel interface



Active Area 48.96x73.44 (mm)

Module PCB Size 60.30x96.60 (mm)

Back Light 6 chip HighLight white LEDs

Operating Temperature -10℃~60℃

Storage Temperature -20℃~70℃

Operating Voltage 3.3V / 5V

Power Consumption TDB

Product Weight About 45(g)

Interface Description

Module pin Silkscreen picture

Number Module Pin Pin Description

1 5V Power pin

2 DB0

Data bus low 8-bit pin 3 DB1

4 DB2



5 DB3

6 DB4

7 DB5

8 DB6

9 DB7

10 DB8

Data bus high 8-bit pin

11 DB9

12 DB10

13 DB11

14 DB12

15 DB13

16 DB14

17 DB15

18 RS LCD register / data selection pin

19 WR LCD write control pin

20 CS LCD chip select control pin

21 RST LCD reset control pin

22 NC Undefined, reserved

23 F_CS Extended application: SPI flash Chip Select Pin

24 MISO SPI bus input pin (extended application)

25 MOSI SPI bus output pin (extended application)

26 CLK SPI bus clock pin (extended application)

27 SD_CS Extended reference: SD card select pin

28 GND Power ground pin

Hardware Configuration

The LCD module hardware circuit comprises three parts: LCD display control circuit,

level conversion circuit, SD card control circuit.

LCD display control circuit for controlling the pins of the LCD, including control pins

and data transfer pins.

Level shifting circuit for 5V/3.3V conversion, making the module compatible with

3.3V/5V power supply.



SD card control circuit is used for SD card function expansion, controlling SD card

identification, reading and writing.

working principle

1. Introduction to ITI9486 Controller

The ITI9486 controller supports a maximum resolution of 320*480 and has a

345600-byte GRAM. It also supports 8-bit, 9-bit, 16-bit, and 18-bit parallel port data buses.

It also supports 3-wire and 4-wire SPI serial ports. Since the supported resolution is

relatively large and the amount of data transmitted is large, the parallel port transmission

is adopted, and the transmission speed is fast. ITI9486 also supports 65K, 262K RGB

color display, display color is very rich, while supporting rotating display and scroll display

and video playback, display in a variety of ways.

The ITI9486 controller uses 16bit (RGB565) to control a pixel display, so it can

display up to 65K colors per pixel. The pixel address setting is performed in the order of

rows and columns, and the incrementing and decreasing direction is determined by the

scanning mode. The ITI9486 display method is performed by setting the address and then

setting the color value.

2. Introduction to parallel port communication

The parallel port communication write mode timing is as shown below:



CSX is a chip select signal for enabling and disabling parallel port communication,

active low

RESX is an external reset signal, active low

D/CX is the data or command selection signal, 1-write data or command parameters,

0-write command

WRX is a write data control signal

D[X:0] is a parallel port data bit, which has four types: 8-bit, 9-bit, 16-bit, and 18-bit.

When performing a write operation, on the basis of the reset, first set the data or

command selection signal, then pull the chip select signal low, then input the content

to be written from the host, and then pull the write data control signal low. When

pulled high, data is written to the LCD control IC on the rising edge of the write control

signal. Finally, the chip select signal is pulled high and a data write operation is

completed.



Instructions for use

1. Arduino instructions

Wiring instructions:

See the interface description for pin assignments.

This module can be directly inserted into the Arduino UNO and Mega2560, no need

to manually wire, as shown below:

Mega2560 directly inserted picture

Direct insertion instructions for Arduino MEGA2560 microcontroller test program pins

Number Module Pin Corresponding to MEGA2560

development board direct plug pins

1 5V 5V



2 DB0 37

3 DB1 36

4 DB2 35

5 DB3 34

6 DB4 33

7 DB5 32

8 DB6 31

9 DB7 30

10 DB8 22

11 DB9 23

12 DB10 24

13 DB11 25

14 DB12 26

15 DB13 27

16 DB14 28

17 DB15 29

18 RS 38

19 WR 39

20 CS 40

21 RST 41

22 NC No need to connect

23 F_CS 45

24 MISO 50

25 MOSI 51

26 CLK 52

27 SD_CS 53

28 GND GND

Operating Steps：

A. Insert the LCD module directly into the Arduino MCU according to the above

wiring instructions, and power on;

B. Copy the dependent libraries in the Install libraries directory of the test package to

the libraries folder of the Arduino project directory (if you do not need to depend



on the libraries, you do not need to copy them);

C. Open the directory where the Arduino test program is located and select the

example you want to test, as shown below:

(Please refer to the test program description document in the test package for the

test program description)

D. Open the selected sample project, compile and download.

The specific operation methods for the Arduino test program relying on library

copy, compile and download are as follows:

http://www.lcdwiki.com/res/PublicFile/Arduino_IDE_Use_Illustration_EN.pdf

E. If the LCD module displays characters and graphics normally, the program runs

Successfully;

2. C51 instructions



STC89C52RC microcontroller test program wiring instructions

Number Module Pin Corresponding to STC89 development board

wiring pin

1 5V 5V

2 DB0 P30

3 DB1 P31

4 DB2 P32

5 DB3 P33

http://www.lcdwiki.com/res/PublicFile/Arduino_IDE_Use_Illustration_EN.pdf



6 DB4 P34

7 DB5 P35

8 DB6 P36

9 DB7 P37

10 DB8 P20

11 DB9 P21

12 DB10 P22

13 DB11 P23

14 DB12 P24

15 DB13 P25

16 DB14 P26

17 DB15 P27

18 RS P12

19 WR P11

20 CS P13

21 RST P14


23 F_CS No need to connect

24 MISO No need to connect

25 MOSI No need to connect

26 CLK No need to connect

27 SD_CS No need to connect

28 GND GND

STC12C5A60S2 microcontroller test program wiring instructions

Number Module Pin Corresponding to STC12 development board

wiring pin

1 5V 5V

2 DB0 P00

3 DB1 P01

4 DB2 P02



5 DB3 P03

6 DB4 P04

7 DB5 P05

8 DB6 P06

9 DB7 P07

10 DB8 P20

11 DB9 P21

12 DB10 P22

13 DB11 P23

14 DB12 P24

15 DB13 P25

16 DB14 P26

17 DB15 P27

18 RS P12

19 WR P11

20 CS P13

21 RST P33







28 GND GND

Operating Steps：

A. Connect the LCD module and the C51 MCU according to the above wiring

instructions, and power on;

B. Open the directory where the C51 test program is located and select the example

to be tested, as shown below:

(Please refer to the test program description document for test program description)



C. Open the selected test program project, compile and download;

detailed description of the C51 test program compilation and download can be

found in the following document:

http://www.lcdwiki.com/res/PublicFile/C51_Keil%26stc-isp_Use_Illustration_EN.pdf

D. If the LCD module displays characters and graphics normally, the program runs

successfully;

3. STM32 instructions



STM32F103RCT6 microcontroller test program wiring instructions

Number Module Pin Corresponding to MiniSTM32 development

board wiring pin

1 5V 5V

2 DB0 PB0

3 DB1 PB1

4 DB2 PB2

5 DB3 PB3

6 DB4 PB4

7 DB5 PB5

8 DB6 PB6

9 DB7 PB7

10 DB8 PB8

11 DB9 PB9

12 DB10 PB10

13 DB11 PB11

http://www.lcdwiki.com/res/PublicFile/C51_Keil%26stc-isp_Use_Illustration_EN.pdf



14 DB12 PB12

15 DB13 PB13

16 DB14 PB14

17 DB15 PB15

18 RS PC8

19 WR PC7

20 CS PC9

21 RST PC10







28 GND GND

STM32F103ZET6 microcontroller test program wiring instructions

Number Module Pin Corresponding to Elite STM32 development

board wiring pin

1 5V 5V

2 DB0 PF0

3 DB1 PF1

4 DB2 PF2

5 DB3 PF3

6 DB4 PF4

7 DB5 PF5

8 DB6 PF6

9 DB7 PF7

10 DB8 PF8

11 DB9 PF9

12 DB10 PF10

13 DB11 PF11

14 DB12 PF12



15 DB13 PF13

16 DB14 PF14

17 DB15 PF15

18 RS PC8

19 WR PC7

20 CS PC9

21 RST PC10







28 GND GND

STM32F407ZGT6 microcontroller test program wiring instructions

Number Module Pin Corresponding to Explorer STM32F4

development board wiring pin

1 5V 5V

2 DB0 PG0

3 DB1 PG1

4 DB2 PG2

5 DB3 PG3

6 DB4 PG4

7 DB5 PG5

8 DB6 PG6

9 DB7 PG7

10 DB8 PG8

11 DB9 PG9

12 DB10 PG10

13 DB11 PG11



14 DB12 PG12

15 DB13 PG13

16 DB14 PG14

17 DB15 PG15

18 RS PC8

19 WR PC7

20 CS PC9

21 RST PC10







28 GND GND

STM32F429IGT6 microcontroller test program wiring instructions

Number Module Pin Corresponding to Apollo STM32F4/F7

development board wiring pin

1 5V 5V

2 DB0 PE0

3 DB1 PE1

4 DB2 PE2

5 DB3 PE3

6 DB4 PE4

7 DB5 PE5

8 DB6 PE6

9 DB7 PE7

10 DB8 PE8

11 DB9 PE9

12 DB10 PE10

13 DB11 PE11



14 DB12 PE12

15 DB13 PE13

16 DB14 PE14

17 DB15 PE15

18 RS PC8

19 WR PC7

20 CS PC9

21 RST PC10







28 GND GND

Operating Steps：

A. Connect the LCD module and the STM32 MCU according to the above wiring

instructions, and power on;

B. Open the directory where the STM32 test program is located and select the

example to be tested, as shown below:

(Please refer to the test program description document for test program description)

C. Open the selected test program project, compile and download;

detailed description of the STM32 test program compilation and download can be



found in the following document:

http://www.lcdwiki.com/res/PublicFile/STM32_Keil_Use_Illustration_EN.pdf

D. If the LCD module displays characters and graphics normally, the program runs

successfully；

Software Description

1. Code Architecture

A. Arduino code architecture description

The code architecture is shown below:

Arduino's test program code consists of two parts: the LCDWIKI library and

application code.

The LCDWIKI library contains two parts: LCDWIKI_KBV library and LCDWIKI_GUI

library;

The application contains several test examples, each with different test content;

LCDWIKI_KBV is the underlying library, which is associated with hardware. It is

mainly responsible for operating registers, including hardware module initialization,

data and command transmission, pixel coordinates and color settings, display mode

configuration, etc;

LCDWIKI_GUI is the middle layer library, which is responsible for drawing graphics

and displaying characters using the API provided by the underlying library;

Sample code

LCDWIKI Library

Application

LCDWIKI_KBV Library LCDWIKI_GUI Library Example1 Example2

http://www.lcdwiki.com/res/PublicFile/STM32_Keil_Use_Illustration_EN.pdf



The application is to use the API provided by the LCDWIKI library to write some test

examples and implement Some aspect of the test function;

B. C51 and STM32 code architecture description

The code architecture is shown below:

The Demo API code for the main program runtime is included in the test code;

LCD initialization and related bin parallel port write data operations are included in the

LCD code;

Drawing points, lines, graphics, and Chinese and English character display related

operations are included in the GUI code;

The main function implements the application to run;

Platform code varies by platform;

2. GPIO definition description

A. Arduino test program GPIO definition description

The module is plugged into the Arduino Mage2560, so it is not allowed to modify the

GPIO port definition.

B. C51 test program GPIO definition description

The C51 test program GPIO definition is placed in the lcd.h file as shown below:

Sample code

test code GUI code LCD code main Platform code



Parallel pin definition needs to select the whole set of GPIO port groups, such as P0,

P2, etc., so that when transferring data, the operation is convenient.Other pins can be

defined as any free GPIO.

C. STM32 test program GPIO definition description

The STM32 test program GPIO definition is placed in the lcd.h file as shown below:

Data parallel port pin definition needs to select a complete set of GPIO port groups,

such as PB, when transferring data, it is convenient to operate.

Other pins can be defined as any free GPIO.

3. Parallel port communication code implementation

A. Arduino test program parallel port communication code implementation

The relevant code is implemented in the mcu_16bit_magic.h file of the

LCDWIKI_KBV library, as shown in the figure below:



Implemented 8-bit and 16-bit commands and 8-bit and 16-bit data write and read.

B. C51 and STM32 test program parallel port communication code

implementation

The relevant code is implemented in the LCD.c file as shown below:

Implemented 8-bit and 16-bit commands and 8-bit and 16-bit data write and read.

Common software

This set of test examples requires the display of Chinese and English, symbols and

pictures, so the modulo software is used. There are two types of modulo software:

Image2Lcd and PCtoLCD2002. Here is only the setting of the modulo software for the test

program.

The PCtoLCD2002 modulo software settings are as follows:

Dot matrix format select Dark code

the modulo mode select the progressive mode

Take the model to choose the direction (high position first)

Output number system selects hexadecimal number



Custom format selection C51 format

The specific setting method is as follows:

http://www.lcdwiki.com/Chinese_and_English_display_modulo_settings

Image2Lcd modulo software settings are shown below:

The Image2Lcd software needs to be set to horizontal, left to right, top to bottom,

and low position to the front scan mode.

http://www.lcdwiki.com/Chinese_and_English_display_modulo_settings

LCDWIKI 3.5inch Arduino 16BIT Module MAR3513 User Manual ...€¦ · LCDWIKI 3.5inch Arduino 16BIT...

Documents

Transcript of LCDWIKI 3.5inch Arduino 16BIT Module MAR3513 User Manual ...€¦ · LCDWIKI 3.5inch Arduino 16BIT...