LCD Color Television - Toshiba Canadaweb1.toshiba.ca/support/ceg/manuals/LCDTV/20HL85_E.pdf ·...
Transcript of LCD Color Television - Toshiba Canadaweb1.toshiba.ca/support/ceg/manuals/LCDTV/20HL85_E.pdf ·...
20HL85
LCD Color Television
Intro
du
ction
Co
nn
ecting
you
r TV
Settin
g u
p yo
ur T
VU
sing
the T
V’s F
eatures
Ap
pen
dix
J3U70221A(E)Cover 05/08/2005, 10:12 AM1
2
Child SafetyIt Makes A DifferenceWhere Your TV StandsCongratulations on your purchase!As you enjoy your new TV, keep these safety tips in mind:
The Issue� If you are like most consumers, you have a TV in your home. Many homes,
in fact, have more than one TV.� The home theater entertainment experience is a growing trend, and larger
TVs are popular purchases; however, they are not always supported onthe proper TV stands.
� Sometimes TVs are improperly secured or inappropriatelysituated on dressers, bookcases, shelves, desks, audio
speakers, chests, or carts. As a result, TVs may fall over,causing unnecessary injury.
Toshiba Cares!� The consumer electronics industry is committed tomaking home entertainment enjoyable and safe.� The Consumer Electronics Association formed the
Home Entertainment Support Safety Committee,comprised of TV and consumer electronics furniture
manufacturers, to advocate children’s safety and educateconsumers and their families about television safety.
Tune Into Safety� One size does NOT fit all! Use appropriate furniture large enough to
support the weight of your TV (and other electronic components).� Use appropriate angle braces, straps, and anchors to secure your furniture
to the wall (but never screw anything directly into the TV).� Carefully read and understand the other enclosed instructions for proper
use of this product.� Do not allow children to climb on or play with furniture and TVs.� Avoid placing any item on top of your TV (such as a VCR, remote control,
or toy) that a curious child may reach for.� Remember that children can become excited while watching a program
and can potentially push or pull a TV over.� Share our safety message about this hidden hazard of the home with
your family and friends. Thank you!
2500 Wilson Blvd.Arlington, VA 22201 U.S.A.Tel. 703-907-7600 Fax 703-907-7690www.CE.org
CEA is the Sponsor, Producer andManager of the International CES®
Dear Customer,Thank you very much for purchasing this Toshiba television.You must carefully read and understand all of the safety instructionscontained in this manual before you attempt to use this product inorder to avoid potential hazards that could cause bodily injury orproperty damage or could damage your Television.We hope that you are completely satisfied with your Toshiba televisionand that it will give you long and enjoyable service. We look forward toproviding you with additional Toshiba products to serve all of yourentertainment needs in the future.
The lightning flash with arrowhead symbol, within anequilateral triangle, is intended to alert the user tothe presence of uninsulated “dangerous voltage”within the product’s enclosure that may be ofsufficient magnitude to constitute a risk of electricshock to persons.
The exclamation point within an equilateral triangle,is intended to alert the user to the presence ofimportant operating and maintenance (servicing)instructions in the literature accompanying theappliance.
CAUTIONRISK OF ELECTRIC SHOCK!
DO NOT OPEN.
NOTE TO CATV INSTALLERSThis is a reminder to call the CATV system installer’s attentionto Article 820-40 of the U.S. NEC, which provides guidelines for propergrounding and, in particular, specifies that the cable ground shall beconnected to grounding system of the building, as close to the point ofcable entry as practical. For additional antenna grounding information,see item 17 on page 4.
CAUTION: TO REDUCE THE RISK OF ELECTRICSHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFERSERVICING TO QUALIFIED SERVICE PERSONNEL.
Safety PrecautionsWARNING: TO REDUCE THE RISK OF FIRE ORELECTRIC SHOCK, DO NOT EXPOSE THISAPPLIANCE TO RAIN OR MOISTURE.
Always read and understand the PRODUCT WARNINGS andUSER DIRECTIONS that are contained in this manual beforeattempting to use your television, to help ensure its safe use.Always store this manual near your television for convenient futurereference.
Intr
od
uct
ion
WARNING:WARNING:WARNING:WARNING:WARNING: Handling the cord on this product or cordsassociated with accessories sold with this product will expose youto lead, a chemical known to the State of California to cause birthdefects or other reproductive harm. Wash hands after handling.
WARNING: Always use a Toshiba-approved wall bracket to wallmount this television. The use of any wall bracket other than aToshiba-approved wall bracket to wall mount this television couldresult in serious bodily injury and/or property damage. For moreinformation call TCL's Customer Service Department at 1-800-268-3404.
CAUTION: To reduce the risk of electric shock, do not usethe polarized plug with an extension cord, receptacle, or otheroutlet unless the blades can be inserted completely to preventblade exposure.
CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THISPOLARIZED PLUG WITH AN EXTENSION CORD, RECEPTACLEOR OTHER OUTLET UNLESS THE BLADES CAN BE FULLYINSERTED TO PREVENT BLADE EXPOSURE.
J3U70221A(E)P02-10 05/08/2005, 10:13 AM2
3
Intro
du
ction
Co
nn
ecting
you
r TV
Settin
g u
p yo
ur T
VU
sing
the T
V’s F
eatures
Ap
pen
dix
IMPORTANT SAFEGUARDS1. READ INSTRUCTIONS
All the safety and operating instructions should be read before the unit is operated.
2. RETAIN INSTRUCTIONSThe safety and operating instructions should be retained for future reference.
3. HEED WARNINGSAll warnings on the unit and in the operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONSAll operating and use instructions should be followed.
5. CLEANINGUnplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosolcleaners. Clean only with a dry cloth.
6. ATTACHMENTSDo not use attachments not recommended by the product manufacturer as they may causehazards.
7. WATER AND MOISTUREDo not use this unit near water, for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement,or near a swimming pool.
8. ACCESSORIESDo not place this product on an unstable cart, stand, tripod,bracket, or table. The product may fall, causing serious injury toa child or adult, and serious damage to the product. Use onlywith a cart, stand, tripod, bracket, or table recommended by themanufacturer, or sold with the product. Any mounting of theproduct should follow the manufacturer’s instructions, andshould use a mounting accessory recommended by themanufacturer.
8A. An appliance and cart combination should be moved with care.Quick stops, excessive force, and uneven surfaces may causethe appliance and cart combination to overturn.
9. VENTILATIONSlots and openings in the cabinet back or bottom are provided for ventilation, and toensure reliable operation of the unit, and to protect it from overheating. These openings mustnot be blocked or covered. The openings should never be blocked by placing the unit on a bed,sofa, rug, or other similar surface. This unit should never be placed near or over a radiator orheat source. This unit should not be placed in a built-in installation such as a bookcase or rackunless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
10. POWER SOURCEThis unit should be operated only from the type of power source indicated on the rating plate. If you are not sure of thetype of power supply to your home, consult your appliance dealer or local power company.
11. GROUNDING OR POLARIZATIONThis unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than theother). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insertthe plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician toreplace your obsolete outlet.
12. POWER-CORD PROTECTIONPower-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or againstthem, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.
13. LIGHTNINGTo protect your unit from a lightning storm, or when it is left unattended and unused for long periods oftime, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damageto the unit due to lightning and power line surges.
Intro
du
ction
S3126A
PORTABLE CART WARNING(symbol provided by RETAC)
DANGER:RISK OF DEATH, SERIOUSPERSONAL INJURY, OREQUIPMENT DAMAGE.
Wide plug
J3U70221A(E)P02-10 05/08/2005, 10:13 AM3
4
IMPORTANT SAFEGUARDS14. POWER LINES
An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or powercircuits, or where it can fall onto or against such power lines or circuits. When installing an outside antenna system,extreme care should be taken to keep from touching such power lines or circuits, as contact with them might be fatal.
15. OVERLOADINGDo not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.
16. OBJECT AND LIQUID ENTRYDo not push objects through any openings in this unit, as they may touch dangerous voltage points or short out partsthat could result in fire or electric shock. Never spill or spray any type of liquid into the unit.
17. OUTDOOR ANTENNA GROUNDINGIf an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded toprovide some protection against voltage surges and built-up static charges, Section 810 of the National ElectricalCode (NEC), ANSI/NFPA 70, provides information with respect to proper grounding of the mast and supportingstructure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antennadischarge unit, connection to grounding electrodes, and requirements for the grounding electrode.
Intr
od
uct
ion
EXAMPLE OF ANTENNAGROUNDING AS PER THENATIONAL ELECTRICAL CODE
ANTENNA DISCHARGE UNIT(NEC SECTION 810-20)
ANTENNA LEAD IN WIRE
GROUNDING CONDUCTORS(NEC SECTION 810-21)
GROUND CLAMPSPOWER SERVICE GROUNDINGELECTRODE SYSTEM (NEC ART 250, PART H)
GROUNDCLAMP
ELECTRIC SERVICEEQUIPMENT
NEC-NATIONAL ELECTRICAL CODE
S2898A
18. SERVICINGDo not attempt to service this unit yourself, as opening or removing covers may expose you todangerous voltage or other hazards. Refer all servicing to qualified service personnel.For example:a. When the power-supply cord or plug is damaged.b. If liquid has been spilled, or objects have fallen into the unit.c. If the unit has been exposed to rain or water.d. If the unit does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operating instructions, as an improper adjustment of othercontrols may result in damage and will often require extensive work by a qualified technician to restore the unit toits normal operation.
e. If the unit has been dropped or the cabinet has been damaged.f. When the unit exhibits a distinct change in performance, this indicates a need for service.
19. REPLACEMENT PARTSWhen replacement parts are required, be sure the service technician uses replacement parts specified by themanufacturer or those that have the same characteristics as the original part.Unauthorized substitutions may result in fire, electric shock or other hazards.
20. SAFETY CHECKUpon completion of any service or repairs to this unit, ask the service technician to perform safety checks todetermine that the unit is in proper operating condition.
21. HEATThe product should be situated away from heat sources such as radiators, heat registers, stoves, or other products(including amplifiers) that produce heat.
J3U70221A(E)P02-10 05/08/2005, 10:13 AM4
5
Intro
du
ction
Co
nn
ecting
you
r TV
Settin
g u
p yo
ur T
VU
sing
the T
V’s F
eatures
Ap
pen
dix
IMPORTANT SAFEGUARDS22. CONNECTING
When you connect the product to other equipment, turn off the power and unplug all of the equipment from the walloutlet. Failure to do so may cause product damage. Read the owner's manual of the other equipment carefully andfollow the instructions when making any connections.
23. HEADPHONESWhen you use headphones, keep the volume at a moderate level. Using headphones continuously at a high volumemay cause hearing damage.
24. LCDDo not press on or allow anything to impact the surface of the viewing screen (LCD panel). The LCD panel inside theTV is fragile and subject to damage. The LCD Panel contains glass and a toxic liquid. If the liquid comes in contactwith your mouth or eyes, or your skin is cut by broken glass, rinse the affected area thoroughly with water and consultyour doctor.• ALWAYS contact a service technician to inspect the TV any time it has been damaged or dropped.
ON DISPOSALThis product contains mercury. Disposal of mercury may be regulated due to environmentalconsiderations. For disposal or recycling information, please contact your local authorities or theElectronic Industrial Alliance: www.eiae.org.
Intro
du
ction
J3U70221A(E)P02-10 05/08/2005, 10:13 AM5
6
PrecautionsNotes on handling� Do not subject the LCD panel to physical shock, such as
dropping it. It may cause unit damage and malfunction.� Retain the original shipping carton and packing
materials. For maximum protection when shipping,repack the unit as it was originally packed at the factory.
� Do not use volatile liquids, such as insecticide, near theunit. Do not leave rubber or plastic products in contactwith the unit for prolonged periods of time. Doing so willleave marks on the finish.
� The top and rear panels of the unit may become warmafter a long period of use. This is not a malfunction.
� When the unit is not in use, turn off the power.� If you do not use the unit for a long period, the unit may
not function properly in the future. Turn on and use theunit occasionally.
Notes on locating the unit� When you place this unit near a TV, radio, or VCR, the
playback picture may become poor and the sound maybe distorted. In this case, place the unit away from theTV, radio, or VCR.
� To avoid damage to this product, never place or storethe TV in direct sunlight; hot, humid areas; or areassubject to excessive dust or vibration.
� Always place the TV on the floor or a sturdy, level stablesurface that can support the weight of the unit. Use asturdy tie between the TV's rear hooks and the rear wall,pillar, etc., or screw the TV to the stand using the TV’srear screw hole or a safety band (see illustration).
Intr
od
uct
ion
Notes on cleaningClean only with a soft, dry, lint-free cloth.
Notes on LCD� The fluorescent tube which illuminates the panel from
the inside will deteriorate with use. When the LCDbecomes dim, flickers, or does not illuminate, contactyour dealer for replacement.
� The brightness of the LCD monitor differs slightlydepending on the viewing angles. Adjust the angle toobtain the best viewing. (The recommended angle is 90degrees to the monitor.)
Screw holes
TV Stand Screw
WallTie
Hooks
Screw
Safety Band
The following symptoms are technical limitations ofLCD Display technology and are not an indication ofmalfunction; therefore, Toshiba is not responsible forperceived defects resulting from these symptoms.
1) An afterimage (ghost) may appear on the screen if a fixed,non-moving image is displayed for a long period of time. Theafterimage is not permanent and will disappear in a shortperiod of time.
Important notes about your LCD TV2) The LCD panel contained in this TV is manufactured using an
extremely high level of precision technology; however, theremay be an occasional pixel (dot of light) that does not operateproperly (does not light, remains constantly lit, etc.). This is astructural property of LCD technology, is not a sign ofmalfunction, and is not covered under your warranty. Suchpixels are not visible when the picture is viewed from a normalviewing distance.
Note: Interactive video games that involve shooting a “gun”type of joystick at an on-screen target may not work with thisTV.
J3U70221A(E)P02-10 05/08/2005, 10:13 AM6
7
Intro
du
ction
Co
nn
ecting
you
r TV
Settin
g u
p yo
ur T
VU
sing
the T
V’s F
eatures
Ap
pen
dix
Introduction ........................................................... 2IMPORTANT SAFEGUARDS ..................................... 3Precautions ................................................................ 6Exploring your new TV................................................ 8Selecting a location for the TV .................................... 9
Connecting your TV .............................................. 9Connecting a VCR ...................................................... 9Connecting a cable converter box or antenna .......... 10Connecting a DVD player/satellite receiver and aVCR .......................................................................... 11Connecting a DVD player with ColorStream®
(component video) and a VCR ................................. 12Connecting a DTV receiver/set-top box withColorStream® (component video) and a VCR .......... 13Connecting a camcorder .......................................... 14Connecting an HDMI™ or a DVI device to theHDMI input ............................................................... 15Connecting a PC (Personal Computer) .................... 16
Power source....................................................... 16Power connection ..................................................... 16
Setting up your TV .............................................. 17Using the remote control .......................................... 17
Preparing the remote control for use .................. 17Installing the remote control batteries ................. 17Using the remote control to operate your otherdevices ................................................................ 17Programming the remote control to operate yourother devices ...................................................... 18Cable TV converter/satellite receiver, VCR andDVD player code tables ...................................... 19Learning about the remote control ...................... 21
Starting setup ........................................................... 22Changing the on-screen display language ......... 22Adding channels to the TV’s memory ................. 23Programming channels automatically ................. 23Adding and erasing channels manually .............. 23Changing channels ............................................. 23
Using the TV’s features ...................................... 24Adjusting the channel settings .................................. 24Switching between two channels ............................. 24Programming your favorite channels ........................ 24Using the LOCKS menu ........................................... 25
Selecting a password .......................................... 25Locking channels ................................................ 26Locking the video inputs ..................................... 26Setting the GameTimerTM .................................... 27Using the panel lock feature ............................... 27
Labeling channels .................................................... 28Selecting the video input source .............................. 29Labeling the video input sources .............................. 29Setting the clock ....................................................... 29Setting the ON timer ................................................. 30Viewing the wide-screen picture formats (480i and480p signals only) .................................................... 31Selecting the cinema mode ...................................... 32Using the ASPECT feature ....................................... 32Setting the sleep timer .............................................. 33Using the closed caption feature .............................. 33Adjusting the picture ................................................. 34
Selecting the picture mode ................................. 34Adjusting the picture quality ................................ 34Using the CableClear® feature ............................ 35Selecting the color temperature .......................... 35Resetting your picture adjustments .................... 35
Adjusting the sound .................................................. 36Muting the sound ................................................ 36Selecting stereo/SAP broadcasts ....................... 36Adjusting the sound quality ................................. 36Resetting your audio adjustments ...................... 37Using the StableSound® feature ......................... 37Using the WOW™ surround sound feature ........ 37Selecting the HDMI audio input source .............. 38
Adjusting the back lighting feature ........................... 38Displaying on-screen information ............................. 38Auto power off .......................................................... 38Understanding the Power Return feature ................. 38Picture/Audio adjustments in the PC mode .............. 39Resetting your picture/audio adjustmentin the PC mode ......................................................... 39
Appendix .............................................................. 40Troubleshooting ........................................................ 40Specifications ........................................................... 41Limited Canada Warranty ......................................... 42
Intro
du
ction
J3U70221A(E)P02-10 05/08/2005, 10:13 AM7
8
Intr
od
uct
ion Exploring your new TV
You can operate your TV by using the buttons on the top panel or the remote control. The side and back panels provide theinputs to connect other equipment to your TV.
Remote control
POWER
INPUT
SELECT
MENU
VOLUM
E +/-
CHANNEL 3 / 4
VIDEO-2 IN
HEADPHONE
ColorStreamHD IN
Right side
Top
Front
Remote sensorPower indicator
Back
Left side
Side panel
The STARTING SETUP feature appearsthe first time you turn on the TV. See page22 for details.
Top panel
Back panel
DC IN HDMI INVIDEO-1 INRF IN
You can adjustthe angle of theTV screen 5°forward or 10°backward fromvertical. Hold thebase of the TVwhile adjustingthe angle.
The volume and channel buttons on the top panel canbe used as / and / buttons while the TV menu isdisplayed on screen.
Approx 10°Approx 5°
PC INCT-885
INPUT DISPLAY
J3U70221A(E)P02-10 05/08/2005, 10:13 AM8
9
Intro
du
ction
Co
nn
ecting
you
r TV
Settin
g u
p yo
ur T
VU
sing
the T
V’s F
eatures
Ap
pen
dix
IN
OUT
VIDEO
IN from ANT
CH 3CH 4
OUT to TV
AUDIOL R
VIDEO-1 IN
Co
nn
ecting
you
r TV
Note:To prevent equipment damage,do not plug in any power cordsuntil you have finishedconnecting all equipment.
You will need:• two coaxial cables• one set of standard A/V cables
Note:If using a mono VCR, connect L/Mono to VCRAudio OUT using only one audio cable. Forbetter picture quality, if your VCR has S-video,you can use an S-video cable instead of thestandard video cable. Do not connect astandard video cable and an S-video cable toVIDEO-1 simultaneously.
Connecting a VCRThis connection allows you to watch local channels and video programs,play or record on the VCR while watching TV, and record from onechannel while watching another channel.
Selecting a location for the TV• Place the TV on the floor or on a sturdy platform in a location where
light does not directly hit the screen.• Place the TV far enough from the walls to allow proper ventilation.
Inadequate ventilation may cause overheating, which may damagethe TV.
Connecting your TVIf you haven’t connected electronic equipment before, or you havebeen frustrated in the past, you may wish to read this section. (Cablesare not supplied.)
• A coaxial cable is the standard cable that comes in from yourantenna or cable converter box. Coaxial cables use “F” connectors.
• Standard A/V (audio/video) cables are usually color coded accord-ing to use: yellow for video and red and white for audio. The redaudio cable is for the stereo right channel, and the white audiocable is for the stereo left (or mono) channel. If you look at the rearpanel of the TV, you will see that the terminals are color coded inthe same manner as the cables.
• S-video cables provide better picture performance than standardvideo cables. S-video cables can only be used with S-videocompatible components.
• Component video cables provide better picture performance thanS-video cables. Component video cables can only be used withcomponent video compatible components.
• HDMI (High Definition Multimedia Interface) cable is for use withvideo equipment that has HDMI output (see page 15).
Cable Lead-infrom cable boxor antenna
Stereo VCR
ANTENNACoaxial Cable
S-VideoCable
AUDIOCables
VIDEOCable
Component videoCables
HDMICable
The unauthorized recording, use, distribu-tion or revision of television programs,videotapes, DVDs, and other materials isprohibited under the Copyright Laws of theUnited States and other countries, and maysubject you to civil and criminal liability.
TV back panel
J3U70221A(E)P02-10 05/08/2005, 10:13 AM9
10
Connecting a cable converter box or antennaThis television has an extended tuning range and can tune most cablechannels without using a cable company supplied converter box. Somecable companies offer "premium pay channels" in which the signal isscrambled. Descrambling these signals for normal viewing requires theuse of a descrambler device, which is generally provided by the cablecompany.
Option 1: For Subscribers to Basic Cable TV ServiceFor basic cable service not requiring a Converter/Descrambler box,connect the incoming 75 ohm Coaxial Cable directly to the AntennaJack on the back of the television.
Option 2: For Subscribers to Scrambled Cable TV ServiceIf you subscribe to a cable service that requires the use of a Converter/Descrambler box, connect the incoming cable to the Converter/Descrambler box and connect the output of the box to the AntennaJack on the back of the television. Follow the connections shown below.Set the television to the output of the Converter/Descrambler box(usually channel 3 or 4) and use the Converter/Descrambler box toselect channels.
Option 3: For Subscribers to Unscrambled Basic Cable withScrambled Premium ChannelsIf you subscribe to a cable service in which basic cable channels areunscrambled and premium channels require the use of a Converter/Descrambler box, you may wish to use a two-set signal splitter (some-times called a "two-set coupler") and an A/B Switch box from the cableinstaller or an electronics supply store. Follow the connections shownbelow. With the switch in the "B" position, you can directly tune anynonscrambled channels on your TV. With the switch in the "A" position,tune your TV to the output of the Converter/Descrambler box (usuallychannel 3 or 4) and use the box to tune scrambled channels.
Note:When you use a converter box with your TV,there may be features that you cannotprogram using the remote control, such aslabeling channels, blocking channels, andprogramming your favorite channels.
From Cable
Cable Box
A B
Cable Box
A / B SwitchSplitter
VIDEO-1 IN
Co
nn
ecti
ng
yo
ur
TV
Option 1:
Option 2:
Option 3:
TV back panel
J3U70221A(E)P02-10 05/08/2005, 10:13 AM10
11
Intro
du
ction
Co
nn
ecting
you
r TV
Settin
g u
p yo
ur T
VU
sing
the T
V’s F
eatures
Ap
pen
dix
Satellite IN
S-VIDEO
IN
OUT
VIDEO AUDIOL R
OUT
VIDEO AUDIOL R
IN from ANT
CH 3CH 4
OUT to TV
OUT to TV
VIDEO-1 IN
Connecting a DVD player/satellite receiverand a VCRThis connection allows you to watch DVD/satellite, VCR, or TV pro-grams. You can record from the satellite receiver and TV, as well asrecord one TV channel while watching another channel.
You will need:• three coaxial cables• two sets of standard A/V cables• one S-video cable
Note:You can use a standard video cable instead ofthe S-video cable, but the picture quality willdecrease. If you use an S-video cablebetween the TV and DVD player/satellitereceiver, make the audio connections butremove the standard video cable. Do notconnect both an S-video and a standardvideo cable to VIDEO1 at the same time orthe picture performance will be unacceptable.
DVD player / Satellite Receiver
Stereo VCR
TV back panel
Co
nn
ecting
you
r TV
The unauthorized recording, use, distribu-tion or revision of television programs,videotapes, DVDs, and other materials isprohibited under the Copyright Laws of theUnited States and other countries, and maysubject you to civil and criminal liability.
From satellite
J3U70221A(E)P11-16 05/08/2005, 10:13 AM11
12
IN
OUT
VIDEO
IN from ANT
CH 3CH 4
OUT to TV
AUDIOL R
OUT
AUDIOOUT
VIDEO
Y
L
R
S-VIDEO
COMPONENT VIDEO
VIDEO-1 IN
You will need:• two coaxial cables• one set of standard A/V cables• one set of component video cables• one pair of standard audio cables
Connecting a DVD player with ColorStream®
(component video) and a VCRThis connection allows you to watch DVD, VCR, or TV programs andrecord TV programs. You can record from one source while watching aprogram from another source. Your TV is capable of using ColorStream(component video). Connecting your TV to a component video compat-ible DVD player, such as a Toshiba DVD player with ColorStream®, cangreatly enhance picture quality and performance.
DVD player with Component video
TV back panel
Stereo VCR
From antenna
Note:The ColorStream HD jacks can be used withProgressive (480p, 720p) and Interlaced(480i, 1080i) scan systems. A 1080i signal willprovide the best picture performance.
Co
nn
ecti
ng
yo
ur
TV
The unauthorized recording, use, distribu-tion or revision of television programs,videotapes, DVDs, and other materials isprohibited under the Copyright Laws of theUnited States and other countries, and maysubject you to civil and criminal liability.
J3U70221A(E)P11-16 05/08/2005, 10:13 AM12
13
Intro
du
ction
Co
nn
ecting
you
r TV
Settin
g u
p yo
ur T
VU
sing
the T
V’s F
eatures
Ap
pen
dix
AUDIOOUT
Y L
RS-VIDEO VIDEOOUT
COMPONENT VIDEO
IN
OUT
VIDEO
IN from ANT
CH 3CH 4
OUT to TV
AUDIOL R
VIDEO-1 IN
Connecting a DTV receiver/set-top box withColorStream® (component video) and a VCR
This connection allows you to watch DTV (digital TV), VCR, and TVprograms, and record DTV and TV programs.Your TV has ColorStream® (component video) inputs. Connecting yourTV to a DTV receiver with component video can greatly enhancepicture quality and realism.
Stereo VCR
DTV Receiverwith Component video
From DTVAntenna
From Antenna
You will need:• three coaxial cables• two sets of standard A/V cables• one set of standard audio cables• one set of component video cables
Note:For HDMI connection, see page 15.The ColorStream HD jacks and HDMI jackscan be used with Progressive (480p, 720p)and Interlaced (480i, 1080i) scan systems.If your DTV receiver does not have compo-nent video, use the S-video and standardaudio connections instead. Do not connectboth an S-video and a standard video cable toVIDEO1 at the same time or the pictureperformance will be unacceptable.
The unauthorized recording, use,distribution, or revision of televisionprograms, videotapes, DVDs, and othermaterials is prohibited under theCopyright Laws of the United States andother countries, and may subject you tocivil and criminal liability.
TV back panel
Co
nn
ecting
you
r TV
J3U70221A(E)P11-16 05/08/2005, 10:13 AM13
14
Connecting a camcorderThis connection allows you to watch videos recorded on a camcorder.
You will need:• one S-video cable• one pair of standard audio cables
VHS Camcorder
Note:For better picture quality, if your camcorderhas S-video, you can use an S-video cable(plus the standard audio cables) instead of astandard video cable.Do not connect both a standard video cableand an S-video cable at the same time, or thepicture performance will be unacceptable.
You will need:• one set of standard AV cables
VIDEO-1 IN
VIDEO AUDIO
L
R
OUT
VIDEO AUDIO
L
R
OUT
S-VIDEO
S-VIDEO
TV side panel
S-VHS Camcorder
Rear lower left of TV
Co
nn
ecti
ng
yo
ur
TV
J3U70221A(E)P11-16 05/08/2005, 10:13 AM14
15
Intro
du
ction
Co
nn
ecting
you
r TV
Settin
g u
p yo
ur T
VU
sing
the T
V’s F
eatures
Ap
pen
dix
Connecting an HDMI™ or a DVI device to the HDMI input
To connect an HDMI device, you will need:• one HDMI cable (type A connector)
For proper operation, it is recommended that you useas short an HDMI cable as possible. You should notencounter difficulty if you use an HDMI cable that isshorter than 16.4 ft (5m).
HDMI cable transfers both video and audio. Separateanalog audio cables are not required (see illustrationbelow).
You must set the HDMI audio input setting to“HDMI” in the AUDIO menu (see page 38).
Some CDVs (Video CDs) may not output digital audiosignals. In that case, you may hear sound by connectinganalog audio cables. If you do use analog audio cables forthis reason, you will need to set the HDMI audio inputsetting to “DVI” to hear the analog audio (see page 38).Note: If you connect an HDMI device and analog audiocables and play media with digital audio output, to heardigital audio you must set the HDMI audio input settingto “HDMI” (page 38).
[1] HDMI = High-Definition Multimedia Interface.[2] DVI = Digital Video Interface.[3] HDCP = High-bandwidth Digital Content Protection.[4] EIA/CEA-861/861B compliance covers the
transmission of uncompressed digital video with high-bandwidth digital content protection, which is beingstandardized for reception of high-definition videosignals.Because this is an evolving technology, it is possiblethat some devices may not operate properly with theTV.
To connect a DVI device, you will need:• one HDMI–to–DVI adapter cable
(HDMI type A connector)
For proper operation, the length of an HDMI-to-DVIadapter cable should not exceed 9.8 ft (3m). Therecommended length is 6.6 ft (2m).
• one pair of standard analog audio cables
An HDMI-to-DVI adapter cable transfers only video.Separate analog audio cables are required (seeillustration below).
You must set the HDMI audio input setting to “DVI”in the AUDIO menu (see page 38).
The HDMI[1] input on your TV receives digital audio anduncompressed digital video from an HDMI device oruncompressed digital video from a DVI[2] device.
This input is designed to accept HDCP[3] program materialin digital form from EIA/CEA-861/861B–compliant[4]
consumer electronic devices (such as a set-top box orDVD player with HDMI or DVI output).
The HDMI input is designed for best performance with highdefinition video signals. It will accept and display 480i,480p, 720p and 1080i signals.
Note: The HDMI jack is not intended for connection toand should not be used with a personalcomputer. For PC connection, see page 16.
HDMI, the HDMI logo, and High-Definition MultimediaInterface are trademarks or registered trademarks of HDMILicensing, LLC.
To ensure that the HDMI or DVI device is reset prop-erly, it is recommended that you follow these proce-dures:• When turning on your electronic components, turn on
the TV first, and then the HDMI or DVI device.• When turning off your electronic components, turn off
the HDMI or DVI device first, and then the TV.
HDMI device
VIDEO AUDIOL R
IN
OUT
HDMIOUT
TV back panel
VIDEO AUDIOL R
IN
OUT
DVIOUT
DVI device
TV back panel
Co
nn
ecting
you
r TV
J3U70221A(E)P11-16 05/08/2005, 10:13 AM15
16
Co
nn
ecti
ng
yo
ur
TV
Connecting a PC (Personal Computer)Before you connect this TV to your PC, change the adjustment of yourPC’s Resolution and Refresh rate. See “Monitor Display modes” atright.Connect one end of a (male to male) VGA cable to the video card ofthe computer and the other end to the VGA connector PC at the side ofthe TV. Fix the connectors firmly with the screws on the plug. In case ofa Multimedia computer, connect the audio cables to the audio outputsof your Multimedia computer and to the AUDIO L and R connectors ofthe PC IN jacks of the TV.Set the video input source to PC mode (see “Selecting the video inputsource” on page 29 and “Picture/Audio adjustments in the PC mode”on page 39). The TV can be used as a computer monitor.
Monitor Display modesMODE Resolution Refresh rateVGA 640x480 60HzSVGA 800x600 56.3HzSVGA 800x600 60.3HzXGA 1024x768 60HzWXGA 1280x720 60HzWXGA 1280x768 60Hz
TV side panel
You will need:• one VGA cable
To PC
Notes:• The current signal source does not display
when you return to TV mode.• The on-screen displays will have a different
appearance in PC mode than in TV mode.• When you select WXGA mode, set the
WXGA INPUT to ON in the PC PICTUREmenu (see page 39.)
Notes:• Make sure to insert the plug of each cord securely.• During use the AC adapter becomes warm. This is not a
malfunction.
WARNING:• Do not connect this unit to the power source using any
device other than the supplied AC adapter or powercord. This could cause fire, electric shock, or damage.
• Do not use with a voltage other than the power voltagedisplayed. This could cause fire, electric shock, ordamage.
• Never lift the AC adapter by holding the AC cord. The ACadapter may fall, causing personal injury or equipmentdamage.
CAUTION:• Do not use the AC adapter if it is covered by a cloth etc.,
or pressed into a narrow area. This results in poordissipation of heat and may cause fire, electric shock, ordamage.
• When this unit is not used for a long time, (e.g., away ona trip) in the interest of safety, be sure to unplug it fromthe wall outlet.
• Do not plug/unplug the plug when your hands are wet.This may cause electric shock.
• If you need to replace the supplied AC adapter or ACcord, the specified AC adapter and AC cord must beused. Contact the dealer that you purchased the unitfrom.
Power sourcePower connectionTo use AC power1.Connect the AC cord to the AC adapter.2.Connect the AC adapter plug into the TV’s DC input jack.3.Connect the AC cord into a wall outlet.
To DCinput jack
AC adapter(supplied)
AC cord(supplied)
AC 120V,60Hz
1
23
J3U70221A(E)P11-16 05/08/2005, 10:13 AM16
17
Intro
du
ction
Co
nn
ecting
you
r TV
Settin
g u
p yo
ur T
VU
sing
the T
V’s F
eatures
Ap
pen
dix
Setting up your TVUsing the remote controlPreparing the remote control for useWith the remote control, you can operate your TV, most cable TVconverters/satellite receivers, VCRs, and DVD players together, even ifthey are different brands. If you will be using your TV with a Toshibasatellite receiver, VCR, or DVD player, your remote control is alreadyprogrammed and ready to use. If you own different brands of cable TVconverters/satellite receivers, VCRs, and/or DVD players, you mustfirst program your remote control. (See “Programming theremote control to operate your other devices," on page 18.)
Installing the remote control batteriesTo install the batteries:
1. Open the battery cover on the back of the remote control.
2. Install two “AAA” size batteries. Match the + and – signs on thebatteries to the signs on the battery compartment.
3. Close the battery cover on the remote control until the lock snaps.
Settin
g u
p yo
ur T
V
CT-885
INPUT DISPLAY
CT-885
INPUT DISPLAY
To control a VCR:
Program the remotecontrol to recognizethe brand of your VCR(see “Programming theremote control tooperate your otherdevices” on page 18.)The buttons shown atright will then controlthe VCR.Press “VCR” first.
Using the remote control to operate your other devicesTo control a cable TVconverter/satellitereceiver:
Program the remotecontrol to recognize thebrand of your cable TVconverter/satellite receiver(see “Programming theremote control to operateyour other devices” onpage 18.) The buttonsshown at right will controlthe cable TV converter/satellite receiver.Press “CBL/SAT” first.
Power
CH RTN(Channel Return)
ChannelNumbers
Input (TV)
Pic Size (TV)
Channel 3 4
Volume +/- (TV)
TV/VCR
Power
CH RTN(Channel Return)
ChannelNumbers
Input (TV)
Pic Size (TV)
Channel 3 4Volume +/- (TV)
VCR controls
Mute (TV)
CBL/SATVCR
Note:The TV remote control may not operate yourVCR, DVD player, or cable TV converter.Refer to the owner's manual supplied withyour other devices to see which features maybe available. Additionally, the remote controlfor this TV may not support certain featuresavailable on the original remote controls foryour other devices, in which case it issuggested that you use the original remotecontrol for the applicable device.
Caution:• Never throw batteries into a fire.
Notes:• Be sure to use AAA size batteries.• Dispose of batteries in a designated disposal area.• Batteries should always be disposed of with the
environment in mind. Always dispose of batteries inaccordance with applicable laws and regulations.
• If the remote control does not operate correctly,or if the operating range becomes reduced,replace batteries with new ones.
• When necessary to replace batteries in theremote control, always replace both batterieswith new ones. Never mix battery types or usenew and used batteries in combination.
• Always remove batteries from remote control if theyare dead or if the remote control is not to be used foran extended period of time. This will prevent batteryacid from leaking into the battery compartment.
J3U70221A(E)P17-24 05/08/2005, 10:13 AM17
18
CT-885
INPUT DISPLAY
CT-885
INPUT DISPLAY
Set
tin
g u
p y
ou
r T
V
Programming the remote control to operateyour other devicesThis remote control is pre-programmed to operate most Toshibasatellite receivers, VCRs, and DVD players. To control a non-Toshibadevice (or a Toshiba device that the remote control is not pre-programmedto operate), you must follow the steps below to program your remote control.1. Refer to the code tables (on pages 19 and 20) to find the
corresponding code for your device.If more than one code is listed, try each one separately until youfind the one that works.
2. If you are programming the remote control to operate your:• Cable TV converter/satellite receiver: Press “CBL/SAT.”• VCR: Press “VCR.”• DVD player: Press “DVD.”
3. While holding down DISPLAY, press the Channel Number buttonsto enter the three-digit code for your device within 10 seconds.Note: If you do not enter the code within 10 seconds from step 3,
or if you enter the wrong code, this operation is canceled.4. Point the remote control at the cable TV converter/satellite
receiver, VCR or DVD player, and press POWER to test the code.• If the device responds, you entered the correct code.• If the device does not respond, repeat steps 1–4 using another code.
5. Press “TV” to control the TV.
For future reference, write down the codes you used:
Cable TV converter/satellite receiver code _____________________
VCR code ______________________________________________
DVD player code _________________________________________
Notes:• When shipped from the factory, the remote
control is set to operate your TV.• Each time you replace the batteries, you
must reprogram the remote control.• Some newer VCRs are capable of working
on either of two remote codes. These VCRshave a switch labeled “VCR1/VCR2.”If your VCR has this kind of switch anddoes not respond to any of the codes foryour VCR, set the switch to the otherposition (VCR1 or VCR2) and reprogramthe remote control.
Display
ChannelNumbers
Program the remotecontrol to recognize thebrand of your DVDplayer (see“Programming theremote control tooperate your otherdevices” below.) Thebuttons shown at rightwill then control theDVD player.Press “DVD” first.
Power
Numberbuttons
DVD Skip/Search /
DVD
Display
TOP Menu
ENTER
DVD MENU
Pic Size (TV)
Mute (TV)
Input (TV)
Volume +/- (TV)
DVD controls
To control a DVD player:
�� �
�
DVD Clear
TVVCR
DVD
CBL/SAT
J3U70221A(E)P17-24 05/08/2005, 10:13 AM18
19
Intro
du
ction
Co
nn
ecting
you
r TV
Settin
g u
p yo
ur T
VU
sing
the T
V’s F
eatures
Ap
pen
dix
Brand Code Brand Code
Cable TV converter/satellite receiver, VCR and DVD player code tables[For CBL/SAT Mode]CABLE BoxBrand CodeABC
ArcherCableviewCenturyCitizenContec
DiamondEagleGEGeminiGeneral InstrumentsHamlinHitachiJasco
061, 062, 063, 082,084, 087, 091, 092,096, 098065, 092, 097, 099064, 094092090, 092, 097083, 085, 086, 088, 093, 098093091061, 062069, 070, 094062, 089, 096093062, 095, 096097
Jerrold
MagnavoxMemorexMulti CanalNovavisionPanasonicPhilcoPhilips
PioneerProscanRadio ShackRCARealisticRecotonSamsung
062, 069, 071, 082, 086, 089, 091, 096072, 096091, 092, 104090101081, 083, 085087066, 067, 068, 070, 072, 073, 074, 075, 091, 092076, 077061, 062092, 097, 099064, 081065102077, 090
Scientific Atlanta
SearsSignatureSignature 2000SprucerStarcom
StargateSylvaniaTeleViewTexscanTocomU. S. ElectronicsUnited CableUniversal
Wards
063, 078, 079, 080, 088, 098, 101, 105095062096081, 085069, 082, 087, 096, 103, 104069, 090095, 100090100071, 084, 085087, 096, 098082065, 092, 097, 099, 102, 103096
Brand Code Brand Code
[For VCR Mode]VCRBrand CodeAdmiralAikoAiwaAkai
AudiovoxBell & HowellBroksonicCalixCarverCCECitizen
ColortymeCraig
Curtis Mathes
Daewoo
DaytronDenonDimensiaElectrohomeEmerson
Fisher
049019018003, 004, 037, 038, 039, 058, 069010007, 068008, 017010026019009, 010, 011, 012, 013, 014, 015, 019, 057, 073005009, 010, 016, 061, 065, 079001, 005, 009, 012, 014, 040, 048, 053, 056, 057011, 013, 015, 017, 018, 019, 057, 078078063001, 048010, 020, 065003, 008, 010, 011, 017, 018, 020, 028, 039, 054, 057, 062,065, 068, 072007, 016, 021, 022, 023, 057, 064, 068, 070, 071, 079
FujiFunaiGarrardGE
Go VideoGoldstar
GradienteHarman KardonHitachi
JBLJC Penney
JensenJVC
Kenwood
KodakLGLloydsLogikLXIMagnasonicMagnavox
004, 041018, 073018001, 002, 009, 040, 042, 048, 056056, 059, 061, 081005, 010, 014, 054, 056, 065, 067018, 065005024, 025, 035, 037, 042, 063, 070, 080076005, 006, 007, 008, 009, 010, 023, 024, 025, 026, 035, 056,061, 063, 065024, 025, 037005, 006, 007, 014, 037, 043, 062, 063, 068, 082005, 006, 007, 012, 014, 037, 043, 053, 068, 071010010053, 073, 079061010061, 065, 078026, 027, 034, 044, 057, 061, 072
Marantz
Memorex
MGAMGNMinoltaMitsubishi
Montgomery WardMotorolaMTCMultitechNEC
NikkoNoblexOptimusOptonicaOrion
Panasonic
Pentax
Pentex ResearchPhilcoPhilipsPioneer
005, 006, 007, 012, 014, 026, 053, 067007, 009, 010, 016, 018, 034, 049, 063, 065, 066, 068, 075,079020, 028, 039056024, 025, 035, 063020, 024, 025, 028, 039, 043, 065049049009, 046, 061009, 012, 018005, 006, 007, 012, 014, 037, 043, 053, 054, 067, 070010009010, 049, 065031054, 057, 062, 065, 068, 072036, 045, 046, 057, 061, 072, 079012, 024, 025, 035, 042, 053, 063014026, 027, 063026, 031, 044, 057006, 024, 043, 055
Brand Code Brand Code
SatelliteBrand CodeAlphastarChaparralDISH NetworkDrake
EchostarExpress VuFujitsuGEGeneral Instruments
HitachiHughes
038, 059034057020, 040, 044, 046, 050, 053018, 041, 051057027008, 009, 013010, 011, 012, 022, 023, 031, 049033033
Hughes NetworkSystemsIntersatJaneilJVCKenwoodMagnavoxOptimusPansatPrimestarProscanRadio ShackRCA
019
048027017, 057029060058036, 052015, 042008, 009, 013022, 023, 030008, 009, 013, 016
RealisticSamsungSonyStar ChoiceStar TrakSTSToshiba
Uniden
Zenith
030059014, 055057025, 026, 037, 054024000, 001, 002, 003, 004, 005, 006, 007, 020, 031, 056021, 028, 030, 032, 035, 039, 043, 045, 047, 058027
Settin
g u
p yo
ur T
V
J3U70221A(E)P17-24 05/08/2005, 10:13 AM19
20
Brand Code Brand Code
VCR (Continued)Brand CodePortlandProscanProtonQuasarRadio ShackRadio Shack/Realistic
RadixRCA
Realistic
RicohRuncoSamsung
Sansui
012, 013, 015001, 002, 048061045010, 031, 065007, 009, 010, 016, 018, 020, 021, 022, 031, 049010001, 002, 003, 009, 024, 025, 029, 035, 040, 042, 045, 048,055, 056, 063, 071, 083007, 009, 010, 011, 016, 018, 020, 021, 022, 031, 049, 051,056, 060, 065, 075, 079047034009, 011, 038, 056, 073, 084006, 037, 043, 061
007, 009, 016, 054, 064, 068, 071, 075, 079, 085008, 011, 017, 028, 030, 057, 065, 072007, 010, 016, 021, 022, 023, 024, 025, 035, 053, 057, 063,064, 065, 068, 071, 075, 079013, 020, 031, 049, 051, 060, 066004, 025, 032, 061049075047, 061004, 032, 033, 041, 052, 058, 070, 074, 076, 077, 080035018, 026, 027, 028, 044, 072018, 051, 053, 073, 079007
Sanyo
Scott
Sears
Sharp
ShintomSignatureSignature 2000SingerSony
STSSylvania
Symphonic
Tandy
TashikoTatungTeacTechnicsTeknikaToshiba
TotevisionUnitecUnitechVector Research
Video Concepts
Wards
White WestinghouseXR-1000Yamaha
Zenith
010037018, 029, 037036010, 018, 065000, 011, 021, 023, 024, 028, 030, 039, 057, 074, 078, 079009, 010, 065073009005, 006, 011, 012, 053005, 006, 011, 012, 039, 053009, 010, 011, 016, 018, 020, 024, 025, 031, 035, 049, 051,056, 057, 060, 065, 066, 079073018005, 006, 007, 014, 037, 053004, 032, 034, 041, 047, 069, 086
Brand CodeCode Brand Code
TV/VCR ComboBrandActionGEGoldstarPanasonic
078059, 062065065
078065079074
PrecisionQuasarRealisticSony
ToshibaZenithTotevision
057065009, 010, 065
Brand Code Brand Code
Portable DVDBrand CodeAiwaAudiovox
093094, 095
024, 096, 099Panasonic RCA 098
Brand Code Brand Code
HTIBBrand CodeLasonic 083 084Panasonic Venturer 085
Brand Code Brand Code
[For DVD Mode]DVDBrand CodeAiwaApexBOSEBroksonicClarionClassicDaewooDenonEmersonFisherFunaiGEGo VideoGPXHitachi
JVC
006, 015016, 017097018019020021022, 023, 024, 025026, 027028 027 001, 029, 030087031005, 032, 033, 034, 035003, 007, 036, 042, 088
037008, 009 004, 038039040026041043 044058010, 045, 046, 047, 048, 049, 050004, 051052, 053, 054, 055001, 056057, 058001, 002, 059, 089
KenwoodKonkaMagnavoxMemorexMintekNADNakamichiNorcentOnkyoOritronPanasonic
PhilipsPioneerProscanQwestarRCA
SampoSamsungSansuiSanyoSharpSherwoodSony
SylvaniaTeacTechnicsTechwoodToshiba
YamahaZenith
060061, 062, 086, 090073063, 091064, 067074 011, 012, 065, 066, 068, 069, 070027 071072075000, 013, 076, 077, 078079, 080, 081014, 082, 092
DVD Code Brand VCR Code DVD Code
[For VCR and DVD Mode]DVD/VCR ComboBrand VCR CodeGo VideoJVCRCA
081082083
SamsungSanyoZenith
087088089
084085086
090091092
Set
tin
g u
p y
ou
r T
V
J3U70221A(E)P17-24 05/08/2005, 10:13 AM20
21
Intro
du
ction
Co
nn
ecting
you
r TV
Settin
g u
p yo
ur T
VU
sing
the T
V’s F
eatures
Ap
pen
dix
CT-885
INPUT DISPLAY
Settin
g u
p yo
ur T
V
INPUT selects the video input source (page 29)
DISPLAY displays status information on-screen (page 38)
MUTE turns off the sound (page 36)
POWER turns the TV on and off
CHANNEL NUMBERS allow direct access to channels (page 24)
CH RTN (Channel Return) returns to the last viewed channel(page 24)
TV selects TV mode
CH 33333 / 44444 cycles through programmed channels (page 23)
VOL +/- adjusts the volume level
VCR selects VCR mode (page 17)
CBL/SAT selects CBL/SAT mode (page 17)
DVD selects DVD mode (page 18)
SLEEP programs the TV to turn off at a set time (page 33)
PIC SIZE cycles through the three picture sizes: Natural,TheaterWide and full (page 31)
FAV � /� (Favorite Channels) cycles through the channels youprogrammed as favorite channels (page 24)
MENU/ENTER accesses the menu system; also sets menuselections (page 22)
EXIT closes on-screen menus (page 22)
DVD MENU access the DVD menu
PAUSE pauses a videotape/DVD
PLAY plays a videotape/DVD
STOP stops a videotape/DVD
DVD SKIP/SEARCH skips DVD chapter
REW rewinds a videotape/DVD
FF fast forwards a videotape/DVD
TOP MENU access the DVD TOP menu
REC starts recording a videotape
DVD CLEAR clears input data in DVD mode
TV/VCR toggles between TV and VCR modes when viewingwhile recording
Learning about the remote control
ChannelNumbers
Menu/Enter
Display
FAV ��(Favorite Channels)
Mute
Stop
Sleep
Input
DVD Menu
Pic Size
CBL/SAT
ExitEnter
Channel 3 /4
FF
Volume +/-
VCR
DVD
TV
PauseSkip/Search
4 ¢
RewTOP Menu
Rec Clear
TV/VCR
POWER
Play
CH RTN(Channel Return)
• Aim the remote control at the remotesensor and press control buttons tooperate.
• Operate the remote control within a 30degree angle on either side of the remotesensor, up to a distance of approx. 16 ft.(5m).
Approx. 5 meters
RemoteSensor
J3U70221A(E)P17-24 05/08/2005, 10:14 AM21
22
CT-885
INPUT DISPLAY
Starting setupThe STARTING SETUP feature appears the first time you turn on theTV, and helps you select the menu language, specify the TV/CABLEsetting, and program channels automatically.IMPORTANT: Make sure that the antenna or cable TV systemconnection is made!
1. Press TV to select the TV mode.2. Press POWER to turn on the TV. The starting setup function
begins and the language setup menu appears on the screen.Press � or � to select your desiredlanguage, then press ENTER.
3. Press � or � to select “TV” or“CABLE”, then press ENTER.
4. Press � or � to select “START”,then press ENTER. If you select“CANCEL” and press ENTER, theSTARTING SETUP stops and changes to the TV screen.
5. Now the “AUTO SETUP” starts. After the starting setup is com-pleted, the TV channel appears on the screen.
• If you press the EXIT button in the process of “AUTO SETUP”the STARTING SETUP stops and changes to the TV screen.
After you have installed the batteries and programmed the remotecontrol, you need to set some preferences on the TV using the menusystem. You can access the menu system with the buttons on theremote control.
• When you make a menu selection, your changes occur immedi-ately. You do not have to press MENU or EXIT to see yourchanges.
• After one minute, the menu screen will automatically close if you donot make a selection. Your changes will still be saved.
• When you are finished programming the menus, press EXIT.
Changing the on-screen display languageYou can choose from three different languages (English, French andSpanish) for the on screen displays. Adjustment menus and messageswill appear in the language of your choice.
To select a language:1. Press TV to select the TV mode.2. Press MENU, then press or until the SETUP menu appears.
3. Press � or � to highlight LANGUAGE.
4. Press or to highlight your desired language.
SETUP
LANGUAGE CLOCK SETTV / CABLECH PROGRAM ADD / ERASE
ENGLISH
12:00AMCABLE
ADD
:SELECT :ADJUST
:SELECT :ADJUST
ENGLISH
12:00AMCABLE
ADD
:SELECT ENTER: SET
LANGUAGE / LANGUE / IDIOMA
ENGLISHFRANÇAISESPAÑOL
Note:The position and size of the on-screen menuschange for some program formats (such as1080i or 720p).
Menu/Enter
Exit
POWER
Set
tin
g u
p y
ou
r T
V
Note:If the remote control does not operate your TV,press the “TV” button on the remote controland try again.
TV
J3U70221A(E)P17-24 05/08/2005, 10:14 AM22
23
Intro
du
ction
Co
nn
ecting
you
r TV
Settin
g u
p yo
ur T
VU
sing
the T
V’s F
eatures
Ap
pen
dix
CT-885
INPUT DISPLAY
Adding channels to the TV’s memory
When you press CH 3 or 4, your TV will stop only on the channels youhave stored in the TV’s channel memory. Follow the steps below toprogram channels into the channel memory.
Programming channels automaticallyYour TV can automatically detect all active channels and store them inits memory. After the TV has stored the channels in its memory auto-matically, you can add or erase channels manually.
To add channels automatically:1. Press TV to select the TV mode.2. Press MENU, then press or to display the SETUP menu.3. Press � or � until the TV/CABLE
selection is highlighted.4. Press or to highlight either
TV or CABLE, depending onwhich you use.If you use an antenna, choose TV.If you use cable, choose CABLE.
5. Press � until the CH PROGRAM selection is highlighted.6. Press to start channel programming. The TV will automatically
cycle through all the TV or Cable channels (depending on which youselected), and store all active channels in the channel memory.While the TV is cycling through the channels, the message“PROGRAMMING NOW-PLEASE WAIT” appears.
7. When channel programming is complete, the message “COMPLETED”appears.
8. Press CH 3 or 4 to view the programmed channels.
Adding and erasing channels manuallyAfter you have programmed the channels automatically, you can addor erase specific channels manually.
To add or erase channels manually:1. Press TV to select the TV mode.2. Select the channel you want to add or erase. If adding channels, you
must select the channel to add using the Channel Number buttons.3. Press MENU, then press or to
display the SETUP menu.4. Press � or � to highlight ADD/
ERASE.5. Press or to select ADD or
ERASE, whichever function youwant to perform.
6. Repeat steps 1-5 for other channels you want to add or erase.
Changing channelsTo change to the next programmed channel:
Press Channel 3 / 4 on the TV or CH 3 / 4 on the remote control.
To change to a specific channel (programmed or unprogrammed):Press the Channel Number buttons (0-9 and 100) on the remote control.For example, to select channel 125, press 100, 2, 5.
SETUP
LANGUAGE CLOCK SETTV / CABLECH PROGRAM ADD / ERASE
ENGLISH
12:00AMTV / CABLE
ADD
:SELECT :ADJUST
In addition to cycling through yourprogrammed channels, the Channel 3 / 4buttons will also cycle through the videoinput sources (page 29) in the orderillustrated below.
PC
ANT (programmed channel) VIDEO1 VIDEO2
HDMI ColorStream HD
Menu
Channel 3 4
ChannelNumbers
Settin
g u
p yo
ur T
V
SETUP
LANGUAGE CLOCK SETTV / CABLECH PROGRAM ADD / ERASE
ENGLISH
12:00AMCABLE
ADD / ERASE
:SELECT :ADJUST
Note:If the remote control does not operate your TV,press the “TV” button on the remote controland try again.
TV
J3U70221A(E)P17-24 05/08/2005, 10:14 AM23
24
CT-885
INPUT DISPLAY
Using the TV’s featuresAdjusting the channel settingsSwitching between two channelsYou can switch between two channels without entering an actualchannel number each time.
To switch between two channels:1. Press TV to select the TV mode.2. Select the first channel you want to view.3. Select a second channel using the Channel Number buttons (0-9, 100).4. Press CH RTN. The previous channel will be displayed.
Each time you press CH RTN, the TV will switch back and forthbetween the two channels.
Programming your favorite channelsYou can preset up to 12 of your favorite channels using the FavoriteChannel Programming feature. Because this feature scans throughonly your favorite channels, it allows you to skip other channels youdo not normally watch.You can still use Channel 3 / 4 to scan through all the channels youprogrammed in the TV’s memory.
To program your favorite channels:1. Press TV to select the TV mode.2. Select a channel you want to program.3. Press MENU, then press or to display the OPTION menu.4. Press � or � to highlight FAVORITE CH.
5. Press to display the FAVORITE CH menu. SET/CLEAR will behighlighted.
6. Press or to highlight SET and press ENTER.7. Press EXIT to return to normal viewing.8. Repeat steps 1-7 for up to 12 channel.
To select your favorite channels:Press the FAV � / � buttons on the remote control to select yourfavorite channels.The FAV � / � buttons will not work until you have programmedyour favorite channels.
To clear your favorite channels:1. Press TV to select the TV mode.2. Select a channel you want to clear.3. Press MENU, then press or to display the OPTION menu.4. Press � or � to highlight FAVORITE CH.5. Press to display the FAVORITE CH menu. SET/CLEAR will be
highlighted.6. Press or to highlight CLEAR.
7. Press ENTER until “0” replaces the channel number you want to erase.8. Press EXIT to return to normal viewing.9. Repeat steps 1-8 for the other channels.
OPTION
ON TIMERFAVORITE CHCH LABELVIDEO LABEL
OFF
:SELECT :ADJUST
FAVORITE CH :CH002
SET / CLEAR TV CABLE SETUP CH 0 0 0 0 0 0 0 0 0 0 0 0RETURN
:SELECT :ADJUST ENTER :SET
FAVORITE CH :CH002
SET / CLEAR TV CABLE SETUP CH 0 0 0 0 0 0 0 0 0 0 0 0RETURN
:SELECT :ADJUST ENTER :CLEAR
Menu/Enter
Exit
ChannelNumbers
FAV
Channel 3 4
CH RTN
Usi
ng
the
TV
’s F
eatu
res
Note:If the remote control does not operate your TV,press the “TV” button on the remote controland try again.
TV
J3U70221A(E)P17-24 05/08/2005, 10:14 AM24
25
Intro
du
ction
Co
nn
ecting
you
r TV
Settin
g u
p yo
ur T
VU
sing
the T
V’s F
eatures
Ap
pen
dix
CT-885
INPUT DISPLAY
Note:If you forget your password, press DISPLAYfour times within five seconds while the TV isin password entering mode. This allows youto reset your password.
Using the LOCKS menuThe LOCK menu includes the CH LOCK, VIDEO LOCK, GAMETIMER, PANEL LOCK, and NEW PASSWORD functions.
Selecting a passwordYou can use these functions after entering the correct password.
To select your password and access the LOCKS menu:1. Press TV to select the TV mode.2. Press MENU, then press or to highlight the LOCKS menu.3. Press � or � to display the password entering mode.
4. Use the Channel Number buttons (0-9) to enter your password.If you are accessing the LOCKS menu for the first time, select afour-digit number to be your password. Press ENTER.
5. Enter the password again to confirm it, and then press ENTER.The LOCKS menu appears.If the wrong password is entered, “ERROR” blinks about 4seconds.
6. You may now set up the LOCKS menu. See “Locking channels”(page 26), “Locking the video inputs” (page 26), “Setting theGameTimerTM” (page 27) or “Using the panel lock feature” (page27).
To change your password:1. Press TV to select the TV mode.2. Press MENU, then press or to display the LOCKS menu.3. Press � or � to display the password entering mode.4. Use the Channel Number buttons (0-9) to enter your password.
Press ENTER. The LOCKS menu appears.5. Press � or � to highlight NEW PASSWORD and press to
display the NEW PASSWORD menu.6. Use the Channel Number buttons (0-9) to enter a new code. Press
ENTER.7. Enter the password again to confirm it, and then press ENTER.8. Press EXIT to return to normal viewing.
LOCKS
NEW PASSWORD
SELECT:[0-9] ENTEREXIT
: SET: END
Note:The password you programmed is also used inthe LOCKS menu; see pages 26-27.
LOCKS
NEW PASSWORD ----
SELECT:[0-9] ENTEREXIT
: SET: END
LOCKS
CONFIRM PASSWORD
SELECT:[0-9] ENTEREXIT
: SET: END
Menu/Enter
ChannelNumbers
Display
Exit
Usin
g th
e TV
’s Featu
res
Note:If the remote control does not operate your TV,press the “TV” button on the remote controland try again.
TV
J3U70221A(E)P25-28 05/08/2005, 10:14 AM25
26
INPUT DISPLAY
INPUT DISPLAY
Locking the video inputsWith the VIDEO LOCK feature, you can lock out the input sources(VIDEO1, VIDEO2, COLORSTREAM HD, HDMI, PC) and channels 3and 4. You will not be able to select the input sources with the INPUTbutton or Channel buttons unless you clear the setting.
To set up the video lock:1. Press TV to select the TV mode.2. Press MENU, then press or to display the LOCKS menu.3. Press � or � to display the password entering mode.4. Use the Channel Number buttons (0-9) to enter your password,
then press ENTER. The LOCKS menu appears.5. Press � or � to highlight VIDEO
LOCK.6. Press or to select:
• OFF: Unlocks all video inputsources.
• VIDEO: Locks VIDEO1, VIDEO2,COLORSTREAM HD, HDMI, PC.
• VIDEO +: Locks VIDEO1, VIDEO2, COLORSTREAM HD,HDMI, PC, channel 3 and channel 4. This option should be usedif you use the antenna terminal to play a video tape.
7. Press EXIT to return to normal viewing.
Note:After programming VIDEO LOCK, changechannels or press the INPUT key beforeturning off the television.
LOCKS
LOCK CH LOCK VIDEO LOCK
GAME TIMER
:SELECT :ADJUST
OFF
OFFOFF / VIDEO / VIDEO+
CH LOCK :CH 002
SET / CLEAR TV CABLE LOCKED CH 0 0 0 0 0 0 0 0 0RETURN
:SELECT :ADJUST ENTER :SET
Menu/Enter
Exit
ChannelNumbers
INPUT
LOCKS
LOCK CH LOCK VIDEO LOCK
GAME TIMER
:SELECT :ADJUST
OFF
OFF
Locking channelsWith the CH LOCK feature, you can lock specific channels. You will notbe able to tune locked channels unless you clear the setting. You canchoose to lock up to nine TV channels and nine cable channels.
1. Press TV to select the TV mode.2. Use the Channel Number buttons (0-9 and 100) to display the
television channel you wish to lock.3. Press MENU, then press or to display the LOCKS menu.4. Press � or � to display the password entering mode.5. Use the Channel Number buttons
(0-9) to enter your password, thenpress ENTER. The LOCKS menuappears.
6. Press � or � to highlight CHLOCK and press to display theCH LOCK menu.
7. Press or to select the follow-ing:• SET– to set the channel as one
to be locked. Then pressENTER.
• CLEAR– to clear all channelsfrom the list of locked channels.Then press ENTER.
8. Repeat steps 1 through 7 to lock other channels. When you arefinished locking channels, press EXIT to return to normal viewing.
If you try to tune a locked channel, the TV will not display it, but willdisplay the nearest unlocked channel.
To unlock channels:1. Press TV to select the TV mode.2. Press MENU, then press or to display the LOCKS menu.3. Press � or � to display the password entering mode.4. Use the Channel Number buttons (0-9) to enter your password,
then press ENTER. The LOCKS menu appears.5. Press � or � to highlight CH LOCK and press to display the
CH LOCK menu.6. Press or to highlight CLEAR and clear all channels from the
list of locked channels. Press ENTER.7. Press EXIT to return to normal viewing.
Note:After programming CH LOCK, changechannels before turning off the television.
Menu/Enter
Exit
ChannelNumbers
Note:If the remote control does not operate your TV,press the “TV” button on the remote controland try again.
TV
TV
Usi
ng
the
TV
’s F
eatu
res
J3U70221A(E)P25-28 05/08/2005, 10:14 AM26
27
Intro
du
ction
Co
nn
ecting
you
r TV
Settin
g u
p yo
ur T
VU
sing
the T
V’s F
eatures
Ap
pen
dix
INPUT DISPLAY
Using the panel lock feature
You can lock the top panel buttons to prevent your settings from beingchanged accidentally (by children, for example). When the panel lockis set to ON, all control buttons on the TV top panel (except POWER)do not operate.
To lock the panel:1. Press TV to select the TV mode.2. Press MENU, then press or to display the LOCKS menu.3. Press � or � to display the password entering mode.4. Use the Channel Number buttons (0-9) to enter your password,
then press ENTER. The LOCKS menu appears.5. Press � or � to highlight PANEL
LOCK and press or to highlightON.If a button on the top panel ispressed, the message “NOTAVAILABLE” appears.
To unlock the panel:Press and hold the VOLUME – button on the TV top panel for about10 seconds until the message "PANEL LOCK:OFF" appears on-screen.
You also can unlock the panel using the menus:1. Press TV to select the TV mode.2. Press MENU, then press or to display the LOCKS menu.3. Press � or � to display the password entering mode.4. Use the Channel Number buttons (0-9) to enter your password,
then press ENTER. The LOCKS menu appears.5. Press � or � to highlight PANEL LOCK, and then press or to
highlight OFF.
LOCKS
PANEL LOCKNEW PASSWORD
:SELECT :ADJUST
ON / OFF
LOCKS
LOCK CH LOCK VIDEO LOCK
GAME TIMER
:SELECT :ADJUST
OFF
OFFOFF / 30 / 60 / 90 / 120
Menu/Enter
Exit
ChannelNumbers
To unlock the video inputs:1. Press TV to select the TV mode.2. Press MENU, then press or to display the LOCKS menu.3. Press � or � to display the password entering mode.4. Use the Channel Number buttons (0-9) to enter your password,
then press ENTER. The LOCKS menu appears.5. Press � or � to highlight VIDEO LOCK and press or to
highlight OFF.6. Press EXIT to return to normal viewing.
Setting the GameTimerTM
With the GameTimerTM feature, you can automatically activate theVIDEO LOCK feature (VIDEO setting) to set a time limit for playing avideo game (30, 60, 90 or 120 minutes).
To set up the GameTimer:1. Press TV to select the TV mode.2. Press MENU, then press or to display the LOCKS menu.3. Press � or � to display the password entering mode.4. Use the Channel Number buttons (0-9) to enter your password,
then press ENTER. The LOCKS menu appears.5. Press � or � to highlight GAME TIMER.6. Press or to select a time limit (30 minutes, 60 minutes, 90
minutes, 120 minutes or OFF).7. Press EXIT to return to normal
viewing. After the GameTimer isprogrammed, the display willappear briefly every ten minutes toremind you that the GameTimer isoperating.When the programmed time isreached, the TV will changechannels automatically and enterVIDEO LOCK mode.
Notes:• Interactive video games that involve shooting
a gun type of joy-stick at an on-screen targetmay not work on this TV.
• To deactivate the GameTimer, set the VIDEOLOCK to OFF (see “Locking the video inputs”page 26).
TV top panel
VOLUME –
Note:If the remote control does not operate your TV,press the “TV” button on the remote controland try again.
TV
Usin
g th
e TV
’s Featu
res
J3U70221A(E)P25-28 05/08/2005, 10:14 AM27
28
CT-885
INPUT DISPLAY
9. Repeat step 8 to enter the rest of the characters.If you would like a blank space inthe label name, you must choosean empty space from the list ofcharacters; otherwise, a dash willappear in that space.
10. Repeat steps 1-9 for other chan-nels. You can assign a label to eachchannel.
11. Press EXIT to return to normal viewing.
To erase channel labels:1. Press TV to select the TV mode.2. Select a channel with a label.3. Press MENU, then press or until the OPTION menu appears.4. Press � or � to highlight CH LABEL.5. Press to display the CH LABEL menu. SET/CLEAR will be
highlighted.6. Press or to highlight CLEAR.7. Press ENTER.8. Repeat steps 1-7 to erase other channel labels.
CH LABEL :CH 025
SET LABEL – – – –
RETURN
:SELECT ENTER : SET
Labeling channelsChannel labels appear above the channel number display each timeyou turn on the TV, select a channel, or press the DISPLAY button.You can choose any four characters to identify a channel.
To create channel labels:1. Press TV to select the TV mode.2. Select a channel you want to label.3. Press MENU, then press or until
the OPTION menu appears.4. Press � or � to highlight CH LABEL.5. Press to display the CH LABEL
menu. SET/CLEAR will be high-lighted.
6. Press or to highlight SET, thenpress ENTER.
7. Press ENTER to highlight LABEL.8. Press or to enter a character in
the first space. Press the buttonrepeatedly until the character youwant appears on the screen. Press ENTER.
Menu/Enter
Exit
ChannelNumbers
OPTION
ON TIMERFAVORITE CHCH LABELVIDEO LABEL
OFF
:SELECT :ADJUST
CH LABEL
SET / CLEAR
LABEL
RETURN
:CH002
– – – –
:SELECTENTER :SET
:ADJUST
Note:The character will change as below.
SPACE
–
+ –
Note:If the remote control does not operate your TV,press the “TV” button on the remote controland try again.
TV
Usi
ng
the
TV
’s F
eatu
res
J3U70221A(E)P25-28 05/08/2005, 10:14 AM28
Intro
du
ction
Co
nn
ecting
you
r TV
Settin
g u
p yo
ur T
VU
sing
the T
V’s F
eatures
Ap
pen
dix
29
CT-885
INPUT DISPLAY
TV
Exit
Setting the clockYou must set the clock before you can program the ON timer.
To set the clock: (Example: 8:30 AM)1. Press TV to select the TV mode.2. Press MENU, then press or to
display the SETUP menu.3. Press � or � to highlight CLOCK
SET.4. Press to highlight the hour
position.5. Press � or � to set the hour, then
press to highlight the minuteposition.
6. Press � or � to set the minutes,then press EXIT to return to normalviewing.
Note:If the power source for the TV is interrupted(for example, the power cord is unplugged ora power failure occurs), you will need to resetthe clock.
Selecting the video input sourcePress INPUT to view a signal fromanother device connected to your TV,such as a VCR or DVD player. You canselect ANT, VIDEO 1, VIDEO 2,ColorStream HD, HDMI or PC depend-ing on which input jacks you used toconnect your devices (see “Connectingyour TV” on page 9).
Pressing INPUT on the remotecontrol displays the current signalsource (press INPUT again or 0-5to change)
You also can use the Channel 3 / 4 buttons to select the video inputsource. In addition to cycling through your programmed channels(page 23), the Channel 3 / 4 buttons will also cycle through thevideo input sources, in the order illustrated below.
PC
ANT (programmed channel) VIDEO1 VIDEO2
HDMI ColorStream HD
Labeling the video input sourcesThe video label feature allows you to label each input source for yourTV from the following preset list of labels:
– : Uses the default label nameVCR : Video cassette recorderDVD : DVD videoDTV : Digital TV set-top boxSAT : Satellite boxCBL : Cable box
To label the video input sources:1. Press TV to select the TV mode.2. Press MENU, then press or to
display the OPTION menu.3. Press � or � to highlight VIDEO
LABEL.4. Press to display the VIDEO
LABEL menu.5. Press � or � to highlight the video
source you want to label.6. Press or to select the desired
label for that input source.7. Press EXIT to return to normal
viewing.
Please note the following regardingthe HDMI source selection:
The HDMI IN jack is not intended forconnection to and should not be usedwith a PC (personal computer). See“Connecting an HDMI or a DVI device tothe HDMI input” on page 15 and“Connecting a PC” on page 16 fordetails.
[0-5] : SELECT
SOURCE SELECTION
0. ANT 1. VIDEO12. VIDEO23. ColorStream HD4. HDMI5. PC
OPTION
ON TIMERFAVORITE CHCH LABELVIDEO LABEL
OFF / OFF / SET
:SELECT :ADJUST
VIDEO LABEL
1.VIDEO12.VIDEO2 3.ColorStream HD4.HDMI
- / VCR / DVD / DTV- SAT / CBL--
:SELECT :ADJUST
SETUP
LANGUAGE CLOCK SETTV / CABLECH PROGRAM ADD / ERASE
ENGLISH
12:00AMCABLE
ADD
:SELECT :ADJUST
SETUP
LANGUAGE CLOCK SETTV / CABLECH PROGRAM ADD / ERASE
ENGLISH
8:30AMCABLE
ADD
:SELECT :ADJUST
INPUT
Note:If the remote control does not operate your TV,press the “TV” button on the remote controland try again.
Menu
Usin
g th
e TV
’s Featu
res
J3U70221A(E)P29 05/08/2005, 10:14 AM29
30
INPUT DISPLAY
Note:After a power failure or disconnection of thepower, the timer settings will be lost.
ON TIMER
ON TIMER 6:00AM
RETURN
CH002CLEAR
:SELECT :ADJUST
ON TIMER
ON TIMER 6:30AM
RETURN
CH002CLEAR
:SELECT :ADJUST
ON TIMER
ON TIMER 6:30AM
RETURN
CH012
:ADJUST ENTER : SET
ONCE / DAILY / CLEAR
Setting the ON timerThis feature allows you to program the TV to turn on automatically at aset time. If you program the ON TIMER to “DAILY,” the TV will turn onevery day at the same time to the same channel until you clear the ONTIMER.
To set the on timer: (Example: Turning on the TV to channel 012 at6:30 AM, DAILY)
1. Press TV to select the TV mode.2. Set the clock, if you have not already done so (see above).3. Press MENU, then press or to display the OPTION menu.4. Press � or � to highlight ON TIMER.5. Press or to highlight SET, then press ENTER. The ON TIMER
menu appears. Press to set the time.6. Press � or � to set the desired hour,
then press .
7. Set the desired minutes and channel,as in step 6.
8. Press to select ONCE or DAILY.9. Press EXIT to return to normal
viewing.
To cancel the on timer:Select CLEAR in step 8 above.Press EXIT to return to normal viewing.
Menu/Enter
Exit
Note:If the remote control does not operate your TV,press the “TV” button on the remote controland try again.
TV
Usi
ng
th
e T
V’s
Fea
ture
s
J3U70221A(E)P30 05/08/2005, 10:14 AM30
Intro
du
ction
Co
nn
ecting
you
r TV
Settin
g u
p yo
ur T
VU
sing
the T
V’s F
eatures
Ap
pen
dix
31
INPUT DISPLAY
Full picture size example
Viewing the wide-screen picture formats(480i and 480p signals only)You can view 480i and 480p format programs in a variety of picturesizes—Natural, TheaterWide, and Full.The way the image displays in any of the picture sizes will varydepending on the format of the program you are viewing. Select thepicture size that displays the current program the way that looks bestto you.
Selecting the picture size1. Press TV to select the TV mode.2. Press PIC SIZE on the remote control.3. Press the corresponding number button (0-2) to select the desired
picture size, as described below and on the next page.
Note:You also can change the picture size byselecting PICTURE SIZE in the SETUPmenu.
PICTURE SIZE
0. NATURAL 1. THEATER WIDE2. FULL
[0-2] : SELECT
Natural picture size• The image is displayed close to its originally formatted proportion.
Some program formats will display with side bars and/or bars at thetop and bottom.
Natural picture size example: The way the image displays will varydepending on the format of the program you are currently watching.
SETUP
CLOSED CAPTION
PICTURE SIZECINEMA MODEASPECTBACK LIGHTING
:SELECT :ADJUST
OFF
FILM ON 16
TheaterWide picture sizeexample
Notes:• The PICTURE SIZE feature is not available
for some program formats (such as 1080ior 720p). Such formats will display inFull picture size.
• Using these functions to change the picturesize (i.e., changing the height/ width ratio)for any purpose other than your privateviewing may be prohibited under theCopyright Laws of the United States andother countries, and may subject you to civiland criminal liability.
Conventional (4:3) picture inNatural size on your wide-screenTV
Conventional (4:3) pictureon a conventional TVscreen
• The center of the picture remainsclose to its original proportion,but the left and right edges arestretched wider to fill the screen.
• The top and bottom edges of thepicture may be hidden.
TheaterWide picture size (for 4:3 format programs)
ChannelNumbers
Pic Size
Full picture size (for 16:9 source programs)
• If receiving a 4:3 format program,the picture is stretched wider to fillthe width of the screen, but notstretched taller.
• None of the picture is hidden.
Note:If the remote control does not operate your TV,press the “TV” button on the remote controland try again.
TV
Usin
g th
e TV
’s Featu
res
J3U70221A(E)P31-36 05/08/2005, 10:14 AM31
32
CT-885
INPUT DISPLAY
If the signal does not include aspect information, the picture size youselected on pages 31 is displayed.
To turn on the ASPECT feature:1. Press TV to select the TV mode.2. Press MENU, then press or until the SETUP menu appears.3. Press � or � to highlight ASPECT, then press or to select
ON.
SETUP
CLOSED CAPTION
PICTURE SIZECINEMA MODEASPECTBACK LIGHTING
:SELECT :ADJUST
OFF
FILM ON / OFF 16
Selecting the cinema modeWhen you view a DVD movie (3:2 pulldown processed) from a DVDplayer connected to the ColorStream (component video) inputs on theTV, smoother and more natural motion can be obtained by setting theCINEMA MODE to FILM.
To set the CINEMA MODE to FILM:1. Press TV to select the TV mode.2. Press MENU, then press or
until the SETUP menu appears.3. Press � or � to highlight CINEMA
MODE, then press or to selectFILM.
To set the CINEMA MODE to VIDEO (off):Press or to select VIDEO in step 3 above.
SETUP
CLOSED CAPTION
PICTURE SIZECINEMA MODEASPECTBACK LIGHTING
:SELECT :ADJUST
OFF
FILM / VIDEO ON 16
Using the ASPECT featureWhen the ASPECT feature is set to ON and the TV receives a480i signal, the picture size is automatically selected (as described inthe following table).
Aspect ratio of signal source
4:3 Normal16:9 Full
4:3 Letter boxNot defined
Automatic aspect size(automatically selectedwhen ASPECT is ON)
NaturalFull
TheaterWideUser-set mode
Menu
Note:If the remote control does not operate your TV,press the “TV” button on the remote controland try again.
TV
Usi
ng
th
e T
V’s
Fea
ture
s
J3U70221A(E)P31-36 05/08/2005, 10:14 AM32
Intro
du
ction
Co
nn
ecting
you
r TV
Settin
g u
p yo
ur T
VU
sing
the T
V’s F
eatures
Ap
pen
dix
33
INPUT DISPLAY
Setting the sleep timerYou can set the TV so it turns off automatically.
To set the sleep timer:Repeatedly press SLEEP on the remote control to set the length oftime until the TV turns off. The clock will increase 10 minutes for eachpress of the SLEEP button (0h00m, 0h10m, ...1h50m, 2h00m). Afterthe sleep timer is programmed, the display will appear briefly everyten minutes to remind you that the sleep timer is operating.
To confirm the sleep timer setting:Press SLEEP one time. The remaining time will be momentarilydisplayed.
To cancel the sleep timer:Repeatedly press SLEEP until the display turns to 0h00m.
Using the closed caption featureThe Closed Caption feature has two options:• Captions—An on-screen display of the dialogue, narration, and
sound effects of programs and videos that are closed-captioned(usually identified in your local TV listing as “CC”).
• Text—An on-screen display of information not related to theprogram, such as weather or stock data (if available in your viewingarea).
To view captions or text:1. Press TV to select the TV mode.2. Tune the TV to the desired program.3. Press MENU, then press or to display the SETUP menu.4. Press � or � to highlight CLOSED CAPTION.
5. Press or to select the desired Closed Caption mode, asfollows:• To view captions, select C1 or C2 (C1 displays translation of the
primary language in your area).Note: If the program or video you selected is not closed-captioned, no captions will display on-screen.
• To view text, select T1 or T2. Note: If text is not available in yourviewing area, a black rectangle may appear on-screen. If thishappens, set the Closed Caption feature to OFF.
• To turn the Closed Caption feature off, highlight OFF in theClosed Caption menu.
Note:A closed caption signal may not be decodedin the following situations:
• when a video tape has been dubbed• when the signal reception is weak• when the signal reception is non-standard
SETUP
CLOSED CAPTION
PICTURE SIZECINEMA MODEASPECTBACK LIGHTING
:SELECT :ADJUST
OFFC1 / C2 / T1 / T2 / OFF
FILM ON 16
Menu
TV
Note:If the remote control does not operate your TV,press the “TV” button on the remote controland try again.
Sleep
Usin
g th
e TV
’s Featu
res
J3U70221A(E)P31-36 05/08/2005, 10:14 AM33
34
INPUT DISPLAY
INPUT DISPLAY
Adjusting the picture quality
You can adjust the picture quality to your personal preferences,including the brightness, contrast, color, tint, and sharpness. Thequalities you choose will be stored automatically in your TV ’s memoryso you can recall them at any time.
To adjust the picture quality:1. Press TV to select the TV mode.2. Press MENU, then press or to display the PICTURE menu.3. Press � or � until the item you want to adjust is highlighted.
Selection Pressing
BRIGHTNESS darker lighterCONTRAST lower higherCOLOR paler deeperTINT reddish greenishSHARPNESS softer sharper
Adjusting the picture
Selecting the picture mode
You can select four picture modes—Sports, Standard, Movie, andMemory—as described in the following table:
To select the picture mode:1. Press TV to select the TV mode.2. Press MENU, then press or to display the PICTURE menu.3. Press � or � to highlight MODE.
4. Press or to highlight the mode you prefer.5. Press EXIT to return to normal viewing.
Mode Picture Quality
SPORTS Bright and dynamic picture (factory-set)STANDARD Standard picture quality (factory-set)MOVIE Movie-like picture setting (factory-set)MEMORY Your personal preferences (set by you; see
“Adjusting the picture quality”)
PICTURE
MODE SPORTS / STANDARD / MOVIE/MEMORYBRIGHTNESSCONTRASTCOLOR TINT SHARPNESS
SPORTS
:SELECT :ADJUST
255025
025
PICTURE
MODE
BRIGHTNESSCONTRASTCOLOR TINT SHARPNESS
SPORTS
:SELECT :ADJUST
255025
025
4. Press or to adjust the level.
5. Press EXIT to return to normal viewing.
Exit
Menu
Menu
Exit
Note:If the remote control does not operate your TV,press the “TV” button on the remote controland try again.
TV
TV
Usi
ng
th
e T
V’s
Fea
ture
s
J3U70221A(E)P31-36 05/08/2005, 10:14 AM34
Intro
du
ction
Co
nn
ecting
you
r TV
Settin
g u
p yo
ur T
VU
sing
the T
V’s F
eatures
Ap
pen
dix
35
CT-885
INPUT DISPLAY
Selecting the color temperature
Change the picture quality by selecting from three preset color tem-peratures—cool, medium, and warm—as described in the followingtable:
To select the color temperature:1. Press TV to select the TV mode.2. Press MENU, then press or to display the PICTURE menu.3. Press � or � to highlight COLOR TEMPERATURE.
4. Press or to highlight the mode you prefer.5. Press EXIT to return to normal viewing.
Resetting your picture adjustments
The RESET function returns your picture quality adjustments to thefollowing factory settings:
Mode ..................... sports Tint ......................... center (0)Brightness ............. center (25) Sharpness .............. center (25)Contrast ................ max (50) Color temperature .. coolColor ..................... center (25)
To reset your picture adjustments:1. Press TV to select the TV mode.2. Press MENU, then press or to display the PICTURE menu.3. Press � or � to highlight RESET, and then press .
Mode Picture Quality
COOL BlueishMEDIUM NeutralWARM Reddish
PICTURE
CableClearCOLORTEMPERATURE
RESET
:SELECT :ADJUST
COOL/MEDIUM/WARM
OFF
COOL
PICTURE
CableClearCOLORTEMPERATURE
RESET
:SELECT :ADJUST
OFF
COOL
Menu
Exit
Using the CableClear®
featureCableClear® reduces visible interference in your TV picture. Thisis useful when receiving a broadcast with a weak signal (especially aCable channel) or playing a video cassette or disc damaged byrepeated use.To turn on the CableClear® feature:
1. Press TV to select the TV mode.2. Press MENU, then press or to display the PICTURE menu.3. Press � or � to highlight CableClear.
4. Press or to select ON.To turn off the CableClear® feature:
Select OFF in step 4.
PICTURE
CableClearCOLORTEMPERATURE
RESET
:SELECT :ADJUST
ON/OFF
COOL
Note:If the remote control does not operate your TV,press the “TV” button on the remote controland try again.
TV
Usin
g th
e TV
’s Featu
res
J3U70221A(E)P31-36 05/08/2005, 10:14 AM35
36
INPUT DISPLAY
Adjusting the sound quality
You can change the sound quality of your TV by adjusting the bass,treble, and balance.
To adjust the sound quality:1. Press TV to select the TV mode.2. Press MENU, then press or until the AUDIO menu appears.3. Press � or � to highlight the item you want to adjust.
4. Press or to adjust the level.• makes the sound quality weaker or decreases the balance in
the right channel, depending on the item selected.• makes the sound quality stronger or decreases the balance in
the left channel, depending on the item selected.
AUDIO
MTSBASSTREBLEBALANCESTABLE SOUND
STEREO
:SELECT :ADJUST
2525
0OFF
To listen to a second audio program (SAP):1. Press TV to select the TV mode.2. Press MENU, then press or to display the AUDIO menu.3. Press � or � to highlight MTS.4. Press or to highlight SAP. The TV speakers will output the
second audio program instead of normal audio.5. Press EXIT to return to normal viewing.
Adjusting the sound
Muting the sound
Press MUTE to temporarily turn off the sound. While the sound is off,the screen will display the word MUTE in the lower right-hand corner.To restore the sound, press MUTE again.
Selecting stereo/SAP broadcasts
The multi-channel TV sound (MTS) feature provides high-fidelity stereosound. MTS also can transmit a second audio program (SAP) contain-ing a second language or other audio information.Note: The MTS feature is not available in VIDEO mode.
When the TV receives a stereo or SAP broadcast, the word “STEREO”or “SAP” displays on-screen every time you turn the TV on, change thechannel, or press DISPLAY.
To listen to stereo sound:1. Press TV to select the TV mode.2. Press MENU, then press or to display the AUDIO menu.3. Press � or � to highlight MTS.4. Press or to highlight STR (stereo).
Notes:• In general, you can leave your TV in stereo mode because the
TV automatically outputs the type of sound being broadcast(stereo or mono).
• If the stereo sound is noisy, select MONO to reduce the noise.
5. Press EXIT to return to normal viewing.
AUDIO
MTSBASSTREBLEBALANCESTABLE SOUND
STR/SAP/MONO
:SELECT :ADJUST
2525
0OFF
Note:A second audio program (SAP) can be heardonly on those TV stations that offer it.
For example, a station might broadcast musicas a second audio program. If you have SAPon, you will see the current program on thescreen but hear music instead of theprogram’s normal audio.
However, if you have SAP on, and the stationyou are watching is not currentlybroadcasting a second audio program, thestation’s normal audio will be output;however, occasionally there is no sound at allin SAP mode. If this happens, set the MTSfeature to STEREO mode.
Note:Adjusting the sound quality (bass, treble andbalance) does not affect the sound that isoutput from the headphone jack.
Mute
Exit
Display
Menu
Note:If the remote control does not operate your TV,press the “TV” button on the remote controland try again.
TV
Usi
ng
th
e T
V’s
Fea
ture
s
J3U70221A(E)P31-36 05/08/2005, 10:14 AM36
Intro
du
ction
Co
nn
ecting
you
r TV
Settin
g u
p yo
ur T
VU
sing
the T
V’s F
eatures
Ap
pen
dix
37
INPUT DISPLAY
Using the StableSound® feature
The StableSound feature limits the highest volume level to preventextreme changes in volume when the signal source is changed.
To turn on the StableSound® feature:1. Press TV to select the TV mode.2. Press MENU, then press or to display the AUDIO menu.3. Press � or � to highlight STABLE SOUND.4. Press or to highlight ON.
To turn off the StableSound® feature:Highlight OFF in step 4 above.
AUDIO
MTSBASSTREBLEBALANCESTABLE SOUND
STEREO
:SELECT :ADJUST
2525
0ON / OFF
Resetting your audio adjustments
The RESET function returns the audio adjustments to the followingfactory settings:Bass ..................center (25)Treble ............... center (25)Balance ............ center (0)
To reset your audio adjustments:1. Press TV to select the TV mode.2. Press MENU, then press or to display the AUDIO menu.3. Press � or � to highlight RESET, and then press .
AUDIO
WOW SRS 3D FOCUS TruBassHDMIRESET
:SELECT :ADJUST
OFFOFFOFF HDMI / DVI
Menu
Using the WOW™ surround sound feature
WOW is a special combination of SRS Labs audio technologies thatcreates a thrilling surround sound experience with deep, rich bassfrom stereo sound sources. Your TV’s audio will sound fuller, richer, andwider. WOW consists of three features; SRS 3D, FOCUS, and TruBass.To adjust the WOW feature:
1. Press TV to select the TV mode.2. Select STEREO mode (see “selecting stereo/SAP broadcasts” on
page 36).3. Press MENU, then press or to display the AUDIO menu.4. Press or to highlight the desired WOW feature you want to adjust.
• SRS 3D — To turn on or off the surround sound effect.• FOCUS — To turn on or off the vocal emphasis effect.• TruBass — To select your desired bass expansion level
(HIGH, LOW or OFF).
5. Press or to adjust the item.
Notes:• If the broadcast is monaural, the SRS 3D
effect will not work.• The headphone jack do not output any of
the WOW audio features.
AUDIO
WOW SRS 3D FOCUS TruBassHDMIRESET
:SELECT :ADJUST
ON / OFFOFFOFFHDMI
Menu
WOW, SRS and symbol are trademarks of SRS Labs, Inc.WOW technology is incorporated under license from SRS Labs, Inc.
Note:If the remote control does not operate your TV,press the “TV” button on the remote controland try again.
TV
TV
Usin
g th
e TV
’s Featu
res
J3U70221A(E)P37-40 05/08/2005, 10:15 AM37
38
INPUT DISPLAY
INPUT DISPLAY
Auto power offThe TV will automatically turn off after approximately 15 minutes if it is tuned to a vacant channel or a station that completesits broadcast for the day and stops broadcasting on that channel. This feature does not work in Video input/PC mode.
Understanding the Power Return featureIf the power is cut off while you are viewing the TV and the power is resupplied, the Power Return feature will turn the TV onautomatically.If the power is going to be off for a long time or you are going to be away from home for a long time, unplug the power cord fromthe wall outlet to prevent the TV from turning on in your absence.
Adjusting the back lighting featureIf your TV is in a bright room, the screen image may be difficult to see.You can use the BACK LIGHTING feature to adjust the screen bright-ness for improved picture clarity.
To adjust the back lighting:1. Press TV to select the TV mode.2. Press MENU, then press or until the SETUP menu appears.3. Press or to highlight BACK LIGHTING.
4. Press a or to adjust the screen brightness.
Displaying on-screen informationPress DISPLAY to display the following on-screen information:
• Clock• Channel number or Video input mode selected• Channel label (if preset)• Stereo or SAP (second audio program) audio status• On timer, Sleep timer (if preset)• Picture size
STEREOSAPON TIMER 12:00AMSLEEP TIMER 2h00m
ANTFULL ABCD
CLOCK 12:00AM CABLE 002
OFF
FILMON16
SETUP
CLOSED CAPTION
PICTURE SIZECINEMA MODEASPECTBACK LIGHTING
:SELECT :ADJUST
Note:The cold cathode fluorescent lamp used forthe back light on this TV has a limited life.When areas on the screen darken, flicker, orno longer light up, the lamp may be at the endof its life. Contact your nearest ToshibaAuthorized Service Station.
Display
Menu
OFFOFFOFF HDMI / DVI
AUDIO
WOW SRS 3D FOCUS TruBassHDMIRESET
:SELECT :ADJUST
Menu
Selecting the HDMI audio input sourceSee page 15 for details on connecting an HDMI or a DVI device to the TV’s HDMI input.If you connect a DVI device, to hear audio you must also connect the analogaudio cables to the HDMI audio IN jacks (see page 15). Set the HDMI audio inputsetting to “DVI” with this connection.If you connect an HDMI device and play media with digital audio output, to heardigital audio set the HDMI audio input setting to “HDMI” with this connection.If you connect an HDMI device but play media with analog audio output (forexample, certain CDVs do not output digital audio), to hear audio you must alsoconnect the analog audio cables to the HDMI audio IN jacks (see page 15).Set the HDMI audio input setting to “DVI” with this connection.
To select the HDMI audio input source:1. Press TV to select the TV mode.2. Press MENU, then press or to display the AUDIO menu.3. Press or to highlight HDMI.4. Press or to select HDMI or DVI.
Note:If the remote control does not operate your TV,press the “TV” button on the remote controland try again.
TV
TV
Usi
ng
th
e T
V’s
Fea
ture
s
J3U70221A(E)P37-40 05/08/2005, 10:15 AM38
Intro
du
ction
Co
nn
ecting
you
r TV
Settin
g u
p yo
ur T
VU
sing
the T
V’s F
eatures
Ap
pen
dix
39
Notes:• If you wish to change the on-screen
language, follow the steps 1-4 on page 22.• If no buttons are pressed for more than
approx. 60 seconds, the PC Monitor Menuscreen will return to normal Monitor screenautomatically.
• The PC Monitor Menu settings are noteffective for normal TV mode, DVD mode orexternal input mode.
Picture/Audio adjustments in the PC modeThere are a number of picture settings you can adjust to optimize theperformance of the unit in PC mode.
Example: Adjust the contrast.1. Press TV to select the TV mode.2. During PC mode, press MENU, then press or to display the
PICTURE menu.3. Press � or � to select CONTRAST.4. Press or to adjust CONTRAST.5. Press EXIT to return to normal viewing.
PICTURE Menu
Menu
Exit
Resetting your picture/audio adjustments in the PCmodeThe RESET function returns your picture quality adjustments to thefollowing factory settings:
PICTURE menu AUDIO menuBrightness ............ center (25) Bass ....................... center (25)Contrast ............... max (50) Treble ..................... center (25)Red ...................... center (25) Balance .................. center (0)Green ................... center (25)Blue ...................... center (25)
To reset your picture adjustments:1. Press TV to select the TV mode.2. Press MENU during PC mode.3. Press 2 or 3 to select the desired menu.4. Press � or � to highlight RESET, and then press .
PICTURE menuBRIGHTNESS: To adjust the brightness of PC Monitor screen.CONTRAST: To adjust the contrast of PC Monitor screen.HOR POSITION: To adjust the horizontal position of the image on
the PC Monitor screen. Each video standard willrequire a different value for this setting.
VER POSITION: To adjust the vertical position of the image onthe PC Monitor screen. Each video standard willrequire a different value for this setting.
PHASE: This must be adjusted after the frequency hasbeen set to optimize picture quality.
CLOCK: To minimize any vertical bars or stripes visibleon the screen background.
RED/GREEN/BLUE: To adjust the color temperature of the PC Monitorscreen.
WXGA INPUT: Set to ON, when you select the WXGA mode onthe PC.
PICTURE
BRIGHTNESSCONTRASTHOR POSITIONVER POSITIONPHASECLOCK
25 50 25 25 25
0
:SELECT :ADJUST
AUDIO
BASSTREBLEBALANCESTABLE SOUNDWOW SRS 3D FOCUS TruBassRESET
25 25 0
OFFOFFOFFOFF
:SELECT :ADJUST
AUDIO Menu
AUDIO menuBASS/STREBLE/BALANCE: To adjust the sound quality of PC
mode.STABLE SOUND: To turn on or off the
StableSound® feature in PCmode.
WOW SRS 3D: To turn on or off the surroundeffect in PC mode.
WOW FOCUS: To turn on or off the vocalemphasis effect in PC mode.
WOW TruBass: To select your desired bassexpansion level (HIGH, LOW orOFF) in PC mode.
DESCRIPTION ABOUT EACH SETTING OPTION
Note:If the remote control does not operate your TV,press the “TV” button on the remote controland try again.
TV
Usin
g th
e TV
’s Featu
res
J3U70221A(E)P37-40 05/08/2005, 10:15 AM39
40
AppendixTroubleshootingBefore calling a service technician, please check the following table for a possible cause of the symptom and some solutions.
Symptom SolutionTV will not turn on • Make sure the connection of the AC adapter and AC cord, then press
POWER.• The remote control batteries may be dead. Replace the batteries.
No picture, no sound • Check the antenna/cable connections.
No sound, picture OK • The sound may be muted. Press VOLUME.• The station may have broadcast difficulties. Try another channel.• The MTS feature may be in SAP mode. Select STR or MONO in the MTS
menu.
Poor sound, picture OK • The station may have broadcast difficulties. Try another channel.• The MTS feature may be in SAP mode. Select STR or MONO in the MTS
menu.
Poor picture, sound OK • Check the antenna connections.• The station may have broadcast difficulties. Try another channel.• Adjust the PICTURE menu.
Poor reception of broadcast channels • The station may have broadcast difficulties. Try another channel.• Check the antenna connections.
Cannot receive above channel 13 • Make sure TV/CABLE is set to CABLE mode.
Unable to select a certain channel • The channel may be blocked by CH LOCK feature, or erased with the add/erase feature.
Cannot access signal input sources (Video1, • Check the VIDEO LOCK feature.Video2, ColorStream HD, HDMI and PC)and/or Channels 3 and 4
Multiple images • The station may have broadcast difficulties. Try another channel.• Use a highly directional outdoor antenna.
Poor color or no color • The station may have broadcast difficulties. Try another channel.• Adjust the TINT and/or COLOR in the PICTURE menu.
Black box on screen • Select OFF in the Closed Caption menu to turn off the Closed Caption Textmode.
No stereo or SAP sound from a • Make sure the MTS feature is set properly (AUDIO menu).known MTS broadcast
The remote control does not operate • Make sure the TV • CBL/SAT • VCR • DVD mode is set properly.• Remove all obstructions between the remote control and the TV.• The remote control batteries may be dead. Replace the batteries.
The top panel buttons do not operate • Check the PANEL LOCK feature.
Poor composite or S-video picture If the TV is connected to an external A/V device (e.g., DVD player, videogame system, set-top box, etc.) always try to use the ColorStream videojacks (and corresponding audio jacks) or the HDMI input (if available) forconnection to such external A/V device. This will reduce the amount of videoprocessing to be performed by the television.
Picture and sound are out of sync As with all products that contain a digital display, in rare instances, whenviewing certain content (e.g., television broadcasts, video games, DVDs) orwith varous audio system connections, you may notice that the picture andsound are slightly out of sync. This phenomenon can be caused by variousfactors including, without limitation, video processing within the TV, videoprocessing in an attached gaming system, and video processing/differentcompression rates used by broadcasters in their programming. You maywant to try one or more of the following suggestions, which may help toreduce the effect of this phenomenon:• If the TV is connected to an A/V receiver that has a programmable audio
delay feature, use this feature to help synchronize the sound to the picture.• If you notice this phenomenon only on certain TV channels, please contact
your local broadcast, cable, or satellite provider to inform them of thisissue.A
pp
end
ix
J3U70221A(E)P37-40 05/08/2005, 10:15 AM40
Intro
du
ction
Co
nn
ecting
you
r TV
Settin
g u
p yo
ur T
VU
sing
the T
V’s F
eatures
Ap
pen
dix
41
SpecificationsNotes:• This model complies with the specifications listed below.• Designs and specifications are subject to change without notice.• This model may not be compatible with features and/or specifications that may be added in the future.
LCD panel 20.04 inches (508.9 mm diagonal)(Screen size is approximate.)Display method Color TFT LCDNumber of pixels 1366 (Horizontal) x 768 (Vertical)Television system NTSC standardTuner type F-SynthChannel coverage VHF: 2 – 13
UHF: 14 – 69Cable TV: 4A, A-5 – A-1, A-I, J – W, W+1 – W+84
Antenna input VHF/UHF 75 ohmPower source 120V AC, 60 Hz with supplied AC adapterPower consumption 100 W with supplied AC adapterAudio power 2.5W + 2.5 WSpeaker type 1.8 x 3.9 inches (45.7 x 99.1 mm), 16 ohm x 2Video/Audio terminals S-VIDEO INPUT
Y-INPUT: 1V (p-p), 75 ohm, negative sync., Mini DIN 4pin x 1C-INPUT: 0.286V (p-p) (burst signal), 75 ohm
VIDEO/AUDIO INPUTVIDEO: 1V (p-p), 75 ohm, negative sync., pin jack x 2AUDIO: 150 mV (rms) (30% modulation equivalent, 47k ohm), pin jack (L/R) x 5
ColorStream® (component video) INPUTY: 1V (p-p), 75 ohmPR: 0.7V (p-p), 75 ohmPB: 0.7V (p-p), 75 ohm
HEADPHONEØ3.5mm stereo mini jack x 1
HDMI INPUT: HDMI compliant (type A connector)HDCP compliantE-EDID* compliantSuggested scan rates: 1080i, 480p, 480i, 720pHDMI Audio: 2-channel PCM
32/44.1/48 kHz sampling frequency16/20/24 bits per sample
PC Monitor InputMini-Dsub 15pin x 1
Dimensions Width: 21-13/16 inches (554 mm)Height: 17-5/8 inches (448 mm)Depth: 8-11/16 inches (220 mm)
Weight 19.8 Ibs. (9.0 kg)Supplied accessories Remote control (CT-885) with two size “AAA” batteries
AC adapterAC cord (for AC adapter)Owner’s Manual (This booklet)
* E-EDID = Enhanced-Extended Display Identification.
WARNING: Always use a Toshiba-approved wallbracket to wall mount this television. The use of anywall bracket other than a Toshiba-approved wallbracket to wall mount this television could result inserious bodily injury and/or property damage. Formore information call TCL's Customer ServiceDepartment at 1-800-268-3404. A
pp
end
ix
J3U70221A(E)P41-44 05/08/2005, 10:15 AM41
42
Toshiba Canada Limited, (“TCL”) makes the following limitedwarranties to original consumers in Canada. THESE LIMITEDWARRANTIES EXTEND TO THE ORIGINAL CONSUMERPURCHASER OR ANY PERSON RECEIVING THIS LCDTELEVISION AS A GIFT FROM THE ORIGINAL CONSUMERPURCHASER AND TO NO OTHER PURCHASER ORTRANSFEREE.LCD TELEVISIONS PURCHASED IN CANADA AND USEDANYWHERE OUTSIDE OF CANADA, INCLUDING, WITHOUTLIMITATION, THE U.S.A. AND MEXICO, ARE NOT COVEREDBY THESE WARRANTIES.LCD TELEVISIONS PURCHASED ANYWHERE OUTSIDE OFCANADA, INCLUDING, WITHOUT LIMITATION, THE U.S.A.AND MEXICO, AND USED IN CANADA ARE NOT COVEREDBY THESE WARRANTIES.
Limited One (1) Year Warranty on Parts and LabourTCL warrants this LCD Television and its parts against defects inmaterials or workmanship for a period of one (1) year after thedate of original retail purchase. DURING THIS PERIOD, TCLWILL, AT TCL’S OPTION, REPAIR OR REPLACE A DEFECTIVEPART WITH A NEW OR REFURBISHED PART WITHOUTCHARGE TO YOU. YOU MUST DELIVER THE ENTIRETELEVISION TO AN AUTHORIZED TCL SERVICE DEPOT. YOUMUST PAY FOR ALL TRANSPORTATION AND INSURANCECHARGES FOR THE TELEVISION TO AND FROM THESERVICE DEPOT.
Rental UnitsThe warranty for LCD Television rental units begins on the date ofthe first rental or thirty (30) days after the date of shipment to therental firm, whichever comes first.
Limited Warranty for Commercial UnitsTCL warrants LCD Televisions that are sold and used forcommercial purposes as follows: all parts are warranted againstdefects in materials or workmanship for a period of ninety (90)days after the date of original retail purchase. DURING THISPERIOD, TCL WILL, AT TCL’S OPTION, REPAIR OR REPLACEA DEFECTIVE PART WITH A NEW OR REFURBISHED PARTWITHOUT CHARGE TO YOU. YOU MUST DELIVER THEENTIRE TELEVISION TO AN AUTHORIZED TCL SERVICEDEPOT. YOU MUST PAY FOR ALL TRANSPORTATION ANDINSURANCE CHARGES FOR THE TELEVISION TO ANDFROM THE SERVICE DEPOT.
Owner’s Manual and Product RegistrationRead this owner’s manual thoroughly before operating this LCDTelevision.Register your LCD Television online at www.toshiba.ca as soonas possible. By registering your LCD Television you will enable TCLto bring you new products specifically designed to meet yourneeds and help us to contact you in the unlikely event a safetynotification is required. Failure to register your LCD Television doesnot diminish your warranty rights.
Your Responsibility
THE ABOVE WARRANTIES ARE SUBJECT TO THEFOLLOWING CONDITIONS:(1) You must retain your original bill of sale or provide other proof
of purchase.(2) All warranty servicing of this LCD TV must be made by an
Authorized TCL Service Depot.(3) The warranties from TCL are effective only if this LCD
Television is purchased in Canada from an authorized TCLdealer and operated in Canada.
(4) Labour service charges for set installation, setup, adjustmentof customer controls, and installation or repair of antennasystems are not covered by this warranty. Reception problemscaused by inadequate antenna systems, misaligned satellitedishes, cable television distribution, VCRs, DVD players/recorders, personal computer level IEEE-1394 devices, andany other connected signal source device are yourresponsibility.
Limited Canada Warrantyfor LCD Televisions, 20” and smaller
(5) Warranties extend only to defects in materials or workmanshipas limited above, and do not extend to any LCD Television orparts that have been lost or discarded by you or to damage tothe LCD Television or parts caused by fires, misuse, accident,Acts of God (such as lightning or fluctuations in electricpower), improper installation, improper maintenance, or use inviolation of instructions furnished by TCL; use or malfunctionthrough simultaneous use of this LCD Television andconnected equipment; or to units that have been modified orhad the serial number removed, altered, defaced, or renderedillegible.
How to Obtain Warranty ServiceIf, after following all of the operating instructions in this manual andreviewing the section entitled “Troubleshooting,” you find thatservice is needed:
(1) To find the nearest TCL Authorized Service Depot, visit TCL’sweb site at www.toshiba.ca.
(2) You must include the original bill of sale (or a copy thereof) orother proof of purchase along with the entire LCD Television tothe Authorized Service Depot. You are responsible for allinbound transportation and insurance charges for the LCDTelevision to the Authorized Service Depot.
For additional information, visit TCL’s website:www.toshiba.ca
ALL WARRANTIES IMPLIED BY THE LAW OF ANY PROVINCEOF CANADA, INCLUDING THE IMPLIED WARRANTIES OFMERCHANTABILITY AND FITNESS FOR A PARTICULARPURPOSE, ARE EXPRESSLY LIMITED TO THE DURATION OFTHE LIMITED WARRANTIES SET FORTH ABOVE. WITH THEEXCEPTION OF ANY WARRANTIES IMPLIED BY THE LAW OFANY PROVINCE OF CANADA AS HEREBY LIMITED, THEFOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OFALL OTHER WARRANTIES, GUARANTEES, AGREEMENTS,AND SIMILAR OBLIGATIONS OF TCL WITH RESPECT TO THEREPAIR OR REPLACEMENT OF ANY PARTS. IN NO EVENTSHALL TCL BE LIABLE FOR CONSEQUENTIAL ORINCIDENTAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,LOST PROFITS, BUSINESS INTERRUPTION, ORMODIFICATION OR ERASURE OF RECORDED DATA CAUSEDBY USE, MISUSE, OR INABILITY TO USE THIS LCDTELEVISION).
No person, agent, distributor, dealer, or company is authorized tochange, modify, or extend the terms of these warranties in anymanner whatsoever. The time within which an action must becommenced to enforce any obligation of TCL arising under thewarranty or under any law of Canada or any province thereof ishereby limited to ninety (90) days from the date you discover, orshould have discovered, the defect. This limitation does not apply toimplied warranties arising under the law of any province of Canada.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS ANDYOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARYFROM PROVINCE TO PROVINCE IN CANADA. SOMEPROVINCES OF CANADA DO NOT ALLOW LIMITATIONS ONTHE DURATION OF AN IMPLIED WARRANTY, WHEN ANACTION MAY BE BROUGHT, OR THE EXCLUSION ORLIMITATION OF INCIDENTAL OR CONSEQUENTIALDAMAGES. THEREFORE, THE ABOVE PROVISIONS MAY NOTAPPLY TO YOU UNDER SUCH CIRCUMSTANCES. [0305]
Ap
pen
dix
J3U70221A(E)P41-44 05/08/2005, 10:15 AM42
Intro
du
ction
Co
nn
ecting
you
r TV
Settin
g u
p yo
ur T
VU
sing
the T
V’s F
eatures
Ap
pen
dix
43
MEMO
Ap
pen
dix
J3U70221A(E)P41-44 05/08/2005, 10:15 AM43
CableClear, ColorStream, TheaterWide and StableSound are registered trademarks of Toshiba America Consumer Products, L.L.C.GameTimer is a trademark of Toshiba America Consumer Products, L.L.C.
Printed in Thailand
TEL.: (905) 470-5400Service Centers:TORONTO: 191 McNABB STREET, MARKHAM, ONTARIO, L3R 8H2, CANADA TEL.: (905) 470-5400MONTREAL: 18050 TRANS CANADA, KIRKLAND, QUEBEC, H9J-4A1, CANADA TEL.: (514) 390-7766VANCOUVER: 22171 FRASERWOOD WAY, RICHMOND, B.C., V62 1J5, CANADA TEL.: (604) 303-2500
J3U70221A(E)P41-44 05/08/2005, 10:15 AM44