LAYING INSTRUCTIONS - Richmond Sand Gravel and...
Transcript of LAYING INSTRUCTIONS - Richmond Sand Gravel and...
Versawall™
Versawall™ Brochure
Adbri Masonry Pty Ltd ABN: 31 009 687 521
Versawall™ and the Adbri Masonry logo are trademarks of Adbri Masonry Pty Ltd.
The Versawall Retaining Wall System is the subject of pending patent applications in Australia and Australian Registered Design No. 334686.
For more inspirational ideas visit www.adbrimasonry.com.au | 1300 365 565
LAYING INSTRUCTIONS - How to build your own wall!
Step 1
Step 3
Step 2
Step 4
Notes - Slope the soil above and below the wall to ensure that water will flow away from and not accumulate near the wall.
- It is advisable to place a dob of adhesive between corner units.
Step 1 - Dig a shallow trench, level and place 100mm of crushed rock in the bottom. Level and compact. Allow for 50mm embedment of the bottom course and 300mm behind the wall for drainage.
Step 2 - Spread and level approximately 25mm of coarse sand as a bedding layer then place the first course of Versawall™ units. Use a stringline for creating a straight line, and level from side to side and front to back. Install a 90mm Agricultural Pipe (on grade) at the rear of the wall for drainage.
Step 3 - Fill Versawall™ cores and 300mm behind each course with granular rock for drainage and carefully compact. Check each course is level before proceeding and stacking each additional row offsetting from the block below to maintain half bond.
Step 4 - On the last course of stacking units, remove locating lugs on top of the Versawall™ blocks, place a line of adhesive front and back and place the capping unit. Apply pressure to secure and use a stringline and level for the best result. (See Pic 3A and 3B)
Pic 1A
Pic 2A
Pic 1B
Pic 2B
Pic 3B
How to build your own internal corner!
Use standard Versawall™ units, remove locating lugs set corner at half bond. Fill cores and 300mm behind each course with granular rock for drainage and carefully compact.
How to build your own external corner!
Use Versawall™ left and right corner units to construct an external corner.1. Remove the two lugs from the corner unit prior to installing the following courses.2. To finish the wall, mitre cut the caps and remove all locating lugs from the top
of the block prior to securing capping units.
Even the corner units feature the unique self locating lugs which makes it very easy to create perfect 90 degree external corners.
The Versawall™ system is a unique interlocking retaining wall system which is perfect
for reclaiming sloping land and constructing garden beds and planter boxes. These blocks
feature a patent pending design with self locating lugs which makes it quick and easy
to build garden walls. The Versawall™ system creates pure vertical retaining walls which
means less yard space is required and a modern look is achieved.Universal Capping Unit
Versawall™ Standard Unit
Versawall™ Corner Unit*
*Versawall® corner units are sold as pairs
BUILdING STePS
Versawall™ units can be used to create steps in your backyard. The simplest step design uses standard units with corner units. The Universal cap is then used as the step treads. Alternatively, bullnose pavers can also be used for step treads.
™ Corner Unit*
AvAILABLe SIzeS
Charcoal Oatmeal Sunstone
Cross Section
Landscape view
ersawalloption 1
option 2
option 3 ersawall
ersawalloption 4
Existing soil
20mm drainage aggregate column and to fill block voids
No structural load within this zone
1.5
1
NOTE: Allow minimum 50mm ebeddment to cover leveling pad
Max 867mm high4 courses + cap
450 x 130mm compacted roadbase or concrete pad
Ø100mm socked subsoil drain 2% fall to discharge at 20m max centres
Adbri Masonry Versawall™ units and Universal caps
300mm
Level slope
Low permeability top soil layer
No structural load within this zone
20MPa concrete leveling pad (600mm x 150mm) 1.5
1
NOTE: Allow minimum 50mm ebeddment to cover leveling pad
Height varies
Foundation replacement zone compacted roadbase 98% min RDD if required (600mm x 150mm)
Additional extent of foundation replacement zone required when NFC infill material is used
Ø100mm socked subsoil drain 2% fall to discharge at 20m max centres
Adbri Masonry Versawall™ units and Universal caps
See Table
Adbri Masonry Versawall™ units and Universal caps
Garden soil
300mm
Max 867mm high4 courses + cap
450 x 130mm compacted roadbaseor concrete pad
20mm drainage aggregate column and to fill block voids
Ø100mm socked subsoil drain 2% fall to discharge at 20m max centres
NOTE: Allow minimum 50mm ebeddment to cover leveling pad
TYPICAL CROSS SeCTION Of veRSAwALL™
NO fINeS CONCReTe (NfC) CROSS SeCTION Of veRSAwALL™
Versawall ™ cross section - Raised planterVersawall ™ cross section - Retaining wall
Maximum unreinforced height is 800mm plus the capping unit. This is four courses plus the cap. This wall can be constructed to heights in excess of 800mm when designed by an engineer and reinforced. Check with your local council for any further requirements regarding building retaining walls in your area.
Notes- Where NFC is used as infill material wall must be founded on foundation replacement zone as
detailed in cross section- Where NFC concrete is used remove one wing from each block to allow for sufficient bond to
develop between wall units and NFC- Walls over 800mm will need to be designed from a certified engineer.
Height (mm) Infill depth (mm)
800 agg 300
1000 NFC* 300
1200 NFC* 350
1400 NFC* 450
300mm
400mm
390mm
250mm
200mm
200mm
60mm
215mm
215mm
unique self interlocking lugs
COLOUR OPTIONS
feATUReS INCLUde
• Very quick and easy to build a wall with these self interlocking blocks
• Build up to 800mm high (4 courses) plus the capping unit
The Versawall™ system is a unique interlocking retaining wall system which is perfect
for reclaiming sloping land and constructing garden beds and planter boxes. These blocks
feature a patent pending design with self locating lugs which makes it quick and easy
to build garden walls. The Versawall™ system creates pure vertical retaining walls which
means less yard space is required and a modern look is achieved.Universal Capping Unit
Versawall™ Standard Unit
Versawall™ Corner Unit*
*Versawall® corner units are sold as pairs
BUILdING STePS
Versawall™ units can be used to create steps in your backyard. The simplest step design uses standard units with corner units. The Universal cap is then used as the step treads. Alternatively, bullnose pavers can also be used for step treads.
AvAILABLe SIzeS
Charcoal Oatmeal Sunstone
Cross Section
Landscape view
ersawalloption 1
option 2
option 3 ersawall
ersawalloption 4
Existing soil
20mm drainage aggregate column and to fill block voids
No structural load within this zone
1.5
1
NOTE: Allow minimum 50mm ebeddment to cover leveling pad
Max 867mm high4 courses + cap
450 x 130mm compacted roadbase or concrete pad
Ø100mm socked subsoil drain 2% fall to discharge at 20m max centres
Adbri Masonry Versawall™ units and Universal caps
300mm
Level slope
Low permeability top soil layer
No structural load within this zone
20MPa concrete leveling pad (600mm x 150mm) 1.5
1
NOTE: Allow minimum 50mm ebeddment to cover leveling pad
Height varies
Foundation replacement zone compacted roadbase 98% min RDD if required (600mm x 150mm)
Additional extent of foundation replacement zone required when NFC infill material is used
Ø100mm socked subsoil drain 2% fall to discharge at 20m max centres
Adbri Masonry Versawall™ units and Universal caps
See Table
Adbri Masonry Versawall™ units and Universal caps
Garden soil
300mm
Max 867mm high4 courses + cap
450 x 130mm compacted roadbaseor concrete pad
20mm drainage aggregate column and to fill block voids
Ø100mm socked subsoil drain 2% fall to discharge at 20m max centres
NOTE: Allow minimum 50mm ebeddment to cover leveling pad
TYPICAL CROSS SeCTION Of veRSAwALL™
NO fINeS CONCReTe (NfC) CROSS SeCTION Of veRSAwALL™
Versawall ™ cross section - Raised planterVersawall ™ cross section - Retaining wall
Maximum unreinforced height is 800mm plus the capping unit. This is four courses plus the cap. This wall can be constructed to heights in excess of 800mm when designed by an engineer and reinforced. Check with your local council for any further requirements regarding building retaining walls in your area.
Notes- Where NFC is used as infill material wall must be founded on foundation replacement zone as
detailed in cross section- Where NFC concrete is used remove one wing from each block to allow for sufficient bond to
develop between wall units and NFC- Walls over 800mm will need to be designed from a certified engineer.
Height (mm) Infill depth (mm)
800 agg 300
1000 NFC* 300
1200 NFC* 350
1400 NFC* 450
300mm
400mm
390mm
250mm
200mm
200mm
60mm
215mm
215mm
unique self interlocking lugs
COLOUR OPTIONS
feATUReS INCLUde
• Very quick and easy to build a wall with these self interlocking blocks
• Build up to 800mm high (4 courses) plus the capping unit
Versawall™
Versawall™ Brochure
Adbri Masonry Pty Ltd ABN: 31 009 687 521
Versawall™ and the Adbri Masonry logo are trademarks of Adbri Masonry Pty Ltd.
The Versawall Retaining Wall System is the subject of pending patent applications in Australia and Australian Registered Design No. 334686.
For more inspirational ideas visit www.adbrimasonry.com.au | 1300 365 565
LAYING INSTRUCTIONS - How to build your own wall!
Step 1
Step 3
Step 2
Step 4
Notes - Slope the soil above and below the wall to ensure that water will flow away from and not accumulate near the wall.
- It is advisable to place a dob of adhesive between corner units.
Step 1 - Dig a shallow trench, level and place 100mm of crushed rock in the bottom. Level and compact. Allow for 50mm embedment of the bottom course and 300mm behind the wall for drainage.
Step 2 - Spread and level approximately 25mm of coarse sand as a bedding layer then place the first course of Versawall™ units. Use a stringline for creating a straight line, and level from side to side and front to back. Install a 90mm Agricultural Pipe (on grade) at the rear of the wall for drainage.
Step 3 - Fill Versawall™ cores and 300mm behind each course with granular rock for drainage and carefully compact. Check each course is level before proceeding and stacking each additional row offsetting from the block below to maintain half bond.
Step 4 - On the last course of stacking units, remove locating lugs on top of the Versawall™ blocks, place a line of adhesive front and back and place the capping unit. Apply pressure to secure and use a stringline and level for the best result. (See Pic 3A and 3B)
Pic 1A
Pic 2A
Pic 1B
Pic 2B
Pic 3B
How to build your own internal corner!
Use standard Versawall™ units, remove locating lugs set corner at half bond. Fill cores and 300mm behind each course with granular rock for drainage and carefully compact.
How to build your own external corner!
Use Versawall™ left and right corner units to construct an external corner.1. Remove the two lugs from the corner unit prior to installing the following courses.2. To finish the wall, mitre cut the caps and remove all locating lugs from the top
of the block prior to securing capping units.
Even the corner units feature the unique self locating lugs which makes it very easy to create perfect 90 degree external corners.