LAVAVAJILLAS · panel features, please see user manual of model you service. 1 Power Button and...

LAVAVAJILLAS

MODELO: DDW-M1212

CONTENTS Introduction....................................................................................... 2 Specification ..................................................................................... 2 Control Panel Features ...................................................................... 2 Component Locator Views ................................................................ 3 Dishwasher Components ................................................................... 4

Control Panel ................................................................................................. 4 Electronic controller ....................................................................................... 5 Outer Door ..................................................................................................... 6 Dispenser ....................................................................................................... 6 Outside panel ................................................................................................. 8 Door Assembly ............................................................................................ 10 Bottom Board............................................................................................... 12 Bottom Door Seal ........................................................................................ 13 Dishwasher Tub Seal.................................................................................... 14 Air breaker and Air inlet .............................................................................. 14 Overflow switch ........................................................................................... 15 Water softener .............................................................................................. 16 Water Valve ................................................................................................. 17 Pressure Switch ............................................................................................ 17 Motor Pump Assembly................................................................................. 20 Sump Assembly ........................................................................................... 21

Troubleshooting .............................................................................. 24 Warranty ......................................................................................... 28

2

It is a freestanding electrical dishwasher offers good washing performance to satisfy every washing requirement. Its electronic control is easy and convenient to operate. The upper and lower racks can hold up to 12 sets of dishes. The size (W: 0.6m, H: 0.85m, D: 0.58m) can easily fit in any corner of the kitchen, and it’s recommended to locate at which the water hose connection is accessible.

Rat ing voltage: 220-240V, 50Hz Heater elements: 1800W (-10%, +5 %) (230V) Circuit: 7.8-9.0A Water pressure: 0.04MPa-1.0MPa Water temperature: Colder water Sets: 8

This guide just gives an example of all models for reference. About all detail of control

panel features, please see user manual of model you service.

1 Power Button and indicator light: turn on/off the power supply.

2 Salt and rinse aid warning lights: to show when the salt container or dispenser need to be refilled.

3 Half washing button and indicator light: After selecting a wash cycle, press this button to select the half washing. (It means that the lower spray arm does not run, so you should load the upper basket only).

4 Display Window: Display program remaining time, delay time, fault codes, etc

5 Delayed Start Button: Press this button to set the delayed hours for washing. You can delay the start of washing up to 24 hours. One press on this button delays the start of washing by one hour.

6 Program button: Press the button to choose the desired program

Specification

Introduction

Control Panel Features

1 2 3 4 5 6 7

8

3

7 Start /Pause Button: Press this button to start or pause the dishwasher, the process pilot lamp will come on when starting.

8 Program indicator light.

Front View

Interior View (With Basket)

Dispenser Compartment View

Component Locator Views

Compartment Lid

Rinse Agent Cap

Sight Glass

Detergent Compartment

Dispenser

Lower basket

Upper basket

Control panel

Baseboard

Right side Panel

4

Interior View of Basin (With Basket Removed)

Back side view

Throughout this manual, features and appearance may vary from your model.

WARNING: Always turn off the electric power supply before servicing any electrical component, making ohmmeter checks, or replacing any parts.

Dishwasher Components

Control Panel

Lower Sprayer

Filter Assembly

Micro-filter

Drain Hose

Inlet Hose

5

Note: All voltage checks should be made with a voltmeter having a full scale range of 250 volts or higher. After service is completed, be sure all safety grounding circuits are complete, all electrical connections are secure, and all access panels are in place.

Removal and Installation 1. Disconnect the electrical supply from the dishwasher. 2. Open the dishwasher door.

3. Remove the 6 screws that connect the control panel cover to the dishwasher door.

4. Close the dishwasher door. 5. Release the door latch and allow the control panel cover to hang

against the dishwasher door.

6. Unscrew the screws and disconnect the wire terminals for replace PCBs, power switch and handle assembly.

The electronic controller allows the user to select the various cleaning

cycles of the dishwasher. All electrical elements in the dishwasher are controlled by the electronic controller.

Removal and Installation 1. Electronic controller box local in the left side of dishwasher. So first

time we should take off the left side panel.（See outside panel）

2. Unscrew 2 screws that fix electronic controller box on left uprights, and take off the electronic controller box by moving it along arrow.

Electronic controller

6

3. Unscrew 1screw and open the electronic controller box cover. 4. Unscrew 1screw and disconnect the wire terminals for replace PCBs.

5. Reverse the above procedure to install.

The outer door covers the door to the dishwasher and protects the detergent dispenser.

Removal and Installation 1. Disconnect power.

2. Open the dishwasher door. 3. Remove the 6 screws and the door panel from the door assembly. Do

not remove the 6 screws that hold the control panel cover to the door assembly.

The dispenser automatically dispenses both the detergent and the rinse agent at the

appropriate times. The dispenser is activated twice during a wash cycle.

Dispenser

Outer Door

Screw

7

2

Cover

The first time the dispenser is activated (1), the lever slides up the right-hand path of the

connecting rod. This action moves the cover catch (2) and releases

the detergent cover.

When deactivated (3), the lever resets to rest under the notch in the center of the connecting rod.

When activated for the second time in a cycle, the lever lifts the connecting rod by the notch, lifting the rinse dispenser plunger (4) and releasing the rinse agent. When deactivated, the lever returns to its original starting position.

The magnetic sensor (5) are connected to rinse aid warning light at control panel by wires. When the indicator lights up, it should add more rinse aid.

Removal and Replacement 1. Remove the out door insulat ion.

2. Disconnect the 4 terminals from the dispenser.

3. Remove the 3 screws and bottom mount ing bracket.

1

4 5

35

4

8

4. Remove the 3 screws and top mounting bracket. 5. Remove the dispenser from door assembly.

Removal and Replacement 1. Disconnect power. 2. Remove the filter assembly, upper and lower basket.

3. Remove the outer door. 4. Remove the 2 screws that connect the top panel 2 cover to the

dishwasher. 5. Take off the top panel and remove the 2 screws.

6. Remove the 2 screws and baseboard from the dishwasher.

7. Remove the 2 screws connected to left and right side baseboard.

Outside panel

Dispenser

Top panel

9

8. Open the door and remove the 4 screws that connect side panels to tub.

9. Remove the 4 screws in the front.

10. Remove the 8 screws at the back.

11. Remove the screws which are fixed to the left and right side panel.

12. Take off the left side panel. 13. Take off the upper rear crosspiece.

14. Take off the Back cover board. 15. Take off the right side panel.

Baseboard Left side baseboard

Right side baseboard

Left side panel

Upper rear crosspiece Right side panel

10

16. Take off the tub insulat ion over the dishwasher tub. 17. Reverse the above procedure to install.

Removal and Replacement 1. Disconnect power.

2. Remove the Outer Door. 3. Remove the 6 screws that connect the control panel cover to the

dishwasher door. (See electronic controller, step 3) 4. Close the dishwasher door.

5. Release the door latch and allow the control panel cover to hang against the dishwasher door.

6. Disconnect the wire terminals from PCBs. 7. Disconnect the 2 terminal lugs from the Door Switch and Latch

Assembly. 8. Disconnect the 4 terminal lugs from the power switch.

9. Disconnect the 4 terminal lugs from the Dispenser switch. 10. Remove the bolt, nut, and ground wire from the door.

11. Pull the wire harness from the door.

Door Assembly

11

Note: There is a door hinge assembly on both the left and right sides of the dishwasher. Both door hinge assemblies must be removed in order to remove the door. The procedure to remove the right- side door hinge assembly is outlined in steps 12 through 21. The left-side door hinge assembly is identical.

12. Mark the posit ion of the spring bolt key in the mounting bracket with a felt-tip marker.

13. Pull the spring and spring bolt key from the mounting bracket. 14. Lift the bottom of the spring loop from the hinge arm stud.

15. Open the dishwasher door approximately 30 degrees. 16. Lift the bottom hinge arm up from the bottom hinge, far enough to expose the hook.

17. Close the dishwasher door.

Caution: The star washer is easily damaged during removal and should not be reused. Order

wire harness

Bolt, Nut, and Ground Wire

Key

Bracket

Hook

Hinge

12

a new set of star washers. 18. Remove the star washer from the dishwasher door hinge.

19. Remove the hinge pin from the dishwasher door hinge.

20. Repeat steps 13 through 20 to remove the left side door hinge assembly.

21. Remove the dishwasher door from the dishwasher. 22. Reverse the above procedure to install.

Removal and replacement 1. Drain up the water in the dishwasher, and disconnect the power supply.

2. Lay down the dishwasher on its back. 3. Remove the 4 screws.

4. Pull out the bottom board.

5. Reverse the above procedure to install。

Bottom Board

Caution: The star washer is easily damaged and should not be reused.

Star washer

Pin

13

The bottom door seal prevents water leakage.

The seal is fitted in a pinched metal groove at the bottom of the dishwasher door.

Removal and Replacement 1. Remove the Outer Door.

2. Remove the Door Assembly (see Door assembly). 3. Grab one end of the bottom door seal and peal it away from the pinched metal groove.

Warning: The pinched metal groove is sharp. Wear Kevlar gloves when removing or installing the door seal. Failure to comply may result in personal injury.

4. Reverse the above procedure to install. Note: When installing the door, seal make sure

it is seated properly in the pinched metal groove. Run your finger over the groove to make sure it is smooth and even for a proper seal.

Bottom Door Seal

14

The dishwasher tub seal prevents water leakage. The seal is fitted in a seal channel that

lines the rim of the dishwasher tub.

Removal and Replacement 1. Open the dishwasher door. 2. Grab one end of the dishwasher tub seal and peal it away from the seal channel

3. Reverse the above procedure to install. Note: When installing the tub seal, make sure it is seated properly in the seal channel. Run

your finger over the seal to make sure it is smooth and even for a proper seal. A correctly installed gasket will have both ends of the gasket equidistant from the bottom of the tub.

The air breaker is mounted on the left side of the tub. Its purpose is to provide a method

of supplying water for the wash and rinse cycles. The air gap prevents the siphoning of wash water from flowing back into the water supply system, should the water pressure drop to less than atmospheric pressure. The water in the air breaker is used to regenerate the water softener.

The air inlet allows air into the tub to permit air flow for dish drying. Also the air can flow out through the air breaker.

Removal and Replacement 1. Remove the outside panel.

2. Open the dishwasher door. 3. Loosen the clamp and disconnect the 3 air breaker hoses from

the air breaker. 4. Rotate the air breaker nut counter clock-wise and remove it.

5. Remove the air breaker.

Air breaker and Air inlet

Dishwasher Tub Seal

Seal Channel

Tub seal

Make sure the seal is seated properly in the seal channel.

15

Air inlet: it is installed to the right side of tub, whose assembly is similar to air breaker assembly. But it should be that the clear plastic air tube is looped around that the air inlet that protrudes into the dishwasher tub and mates with the air inlet nut.


The overflow switch is designed to detect an overflow. When inlet water is too much or

some components are broken, it will do and E4 will be displayed in the display window in control panel.


2. Remove the bottom board (see bottom board). 3. Disconnect the 2 terminal lugs plugged on the overflow switch, then take off the float

support.

Overflow switch

16

The water softener is equipped with a special softener that uses a salt specifically

designed to eliminate lime and minerals from the water. If hard water is used in the dishwasher, deposits will form on the dishes and utensils.

Removal and Replacement 1. Open the dishwasher door.

2. Remove the top panel, left side panel, right side panel, baseboard and bottom board (see outside panel).

3. Remove the 4 terminal lugs connected to the water softener. 4. Loosen the clamp and disconnect the 3 hoses from the water softener.

5. Remove the lower basket and then unscrew and remove the cap from the salt container.

Note: The clamping nut turns counter clock-wise and

may be difficult to remove. It may be necessary to insert a screw driver or other tool between the clamping nut tabs to enable you to apply sufficient torque to break the factory seal.

6. Remove the clamping nut. 7. Remove the gasket (not shown) and the water

softener. 8. Reverse the above procedure to install.

Note: When remove softener and conjoint hoses, some salt water will flow out. Make sure to wipe off the water and operate a rinse procedure after replacement.

Water softener

Tab

Clamping Nut

17

The water valve is electrical controlled and solenoid operated. The flow of water is controlled by a

rubber flow washer capable of maintaining a flow of 4±15% liters per minute with incoming water

pressure of 0.04~1MPa.The water valve is mounted to the back hinge support of the dishwasher.

Removal and Replacement 1. Disconnect power. 2. Remove the top panel, left side panel, right side panel,

baseboard and bottom board (see outside panel). 3. Disconnect the 2 terminal lugs from the water fill

valve. 4. Push the valve from the bottom to take it off.

5. Remove the clamp and disconnect the tub fill hose

from the water valve.


The pressure switch is located under the tub at the left, front corner. A clear plastic tube, the pressure switch

hose, runs from the pressure switch, around the air inlet, and to the sump. As the dishwasher basin fills with water,

the air pressure in the pressure switch hose increases. When the pressure reaches the aim of value, the switch

will act and give a signal to electronic controller.

Pressure Switch

Water Valve

Water valve

Clamp

Terminals

Pressure switch

Water inlet

Presure switch hose

Left side of dishwasher show the path of the pressure switch hose.

18

Removal and Replacement 1. Disconnect power. 2. Remove the top panel, left side panel, right side panel, baseboard and bottom board

(see outside panel).

3. Remove the capillary tube from the pressure switch. 4. Turn the pressure switch clockwise to align the mounting tab vertically with the

mounting hole and remove the pressure switch from the dishwasher frame. 5. Label and disconnect the 2 terminal lugs from the pressure switch and remove it.


Drain Pump Assembly

The drain pump assembly is located under the tub at the left rear corner. When operated with 230V power, the pump will drain the water out of the dishwasher. A check valve flapper at the outlet of the pump prevents the dirty water from flowing back to the dishwasher.

Removal & replacement 1、disconnect power 2、remove the bottom board。 3、label and disconnect the terminals of the pump

4、remove the two screws of the pump

Terminals

19

5、remove the pump by rotating the pump for 30°counterclockwise

6、Reverse the above procedure to install

Sump Assembly The sump assembly consists of the filter assembly, micro-filter, sump clamping nut, sump gasket,

and sump. The filter assembly prevents large particles from reaching the micro-filter, and the micro-filter prevents all small particles from flowing back to the cycle water. The filter assembly rests above the sump and the micro-filter sits above the sump basin. The clamping nut fixes the sump to the bottom of the dishwasher. The filter assembly, micro-filter, and sump clamping nut are assembled from inside to outside. The gasket and sump are located under the tub bottom in front of the motor pump assembly.

Removal & replacement 1、disconnect power 2、remove top panel, left/ right panel and bottom board 3、remove the pressure switch hose connected with the sump

Pressure

Switch Hose

20

4、remove the interconnect hose connected with the sump

The motor pump assembly is located under the tub behind the sump assembly. This

dishwasher model uses a capacitor start induction motor. The motor rotates clock- wise and draws approximately 0.6 amp


2. Remove the top panel, left side panel, right side panel, baseboard and bottom board (see outside panel).

3. Label and disconnect the 2 terminals to the capacitor.

4. Label and disconnect the 2 terminals to the motor wire connector.

Caution: The clamp is easily damaged during removal and should not be reused. Replace the old clamp with a new universal clamp.

5. Remove the clamp from the motor sump interconnect hose. 6. Remove the clamp from the motor main conduit interconnect hose.

Motor Pump Assembly

Terminals

Capacitor

Connector

Interconnect Hose

21

7. Remove the clamp from the motor washer arm interconnect hose. Note: Do not attempt to remove the bolt and locknut that connects the motor mount to the

dishwasher frame.

8. Remove the screw and disconnect the ground wire from the wash pump motor

assembly. 9. Pull the motor mount back far enough to clear the motor tab, work the motor from the

attaching hoses, and remove the motor pump assembly from the dishwasher. 10. Reverse the above procedure to install.

The sump assembly consists of the filter assembly, micro-filter, sump clamping nut,

sump gasket, and sump. The filter assembly prevents large particles from reaching the micro-filter and the micro- filter prevents small particles from reaching the sump. The filter assembly rests above the sump and the micro-filter sits above the sump basin. The clamping nut holds the sump gasket and sump to the bottom of the dishwasher.

The filter assembly, micro-filter, and sump clamping nut are accessed from inside the dishwasher. The gasket and sump are located under the tub in front of the motor pump assembly.

Removal and Replacement 1. Disconnect power. 2. Remove the top panel, left side panel, right side panel, baseboard and bottom board

Sump Assembly

Lock nut

interconnect hose clamp

22

(see outside panel). 3. Remove the pressure switch hose from the sump.

4. Remove the clamp from the hose that connects the sump to the wash pump motor

hose.

Note: The sump clamping nut turns counterclockwise and may be difficult to remove. It may be necessary to insert a screw driver or other tool between the clamping nut tabs to enable you to apply sufficient torque to break the factory seal.

5. Remove the clamp from the hose that connects the sump to the drain pump assembly.

6. Open the dishwasher door and remove the lower basket (not shown). 7. Remove the filter assembly and micro-filter.

9. Remove the clamping nut.

Pressure switch hose

Sump

Clamp

Interconnect hose

Filter assembly

Plane filter

Micro filter

23

10. Remove the sump gasket (not shown) and sump.


Turn Clamping nut

24

1. Error code troubleshooting Symptom Check for the following Solution

ERROR001(E1)

The water supply is turned off Turn the water supply on The pipe was snapped Put the pipe in the right way Low water pressure Minimum water pressure of 0.04MPa Defective water fill valve Replace the water fill valve Obstructed water fill valve or hose Disassemble and clean the water fill valve and hose Damaged or defective wiring Repair the wiring Defective pressure switch Replace the pressure switch Heavy water usage elsewhere in home Use dishwasher when water usage is at a minimum. Defective the electric control Replace the electric control

ERROR003(E3)

The voltage too low Minimum voltage of 198V Damaged the thermostat Replace the thermostat Damaged or defective wiring Repair the wiring Damaged the NTC thermistor Replace the thermistor Damaged the heating element Replace the heating element Defective the electric control Replace the electric control

ERROR004(E4)

The sump or the filter was obstructed Clear the sump and filter Soap suds leak from dishwasher Refer to owner’s manual Damaged the sump / motor pump / tub Repair or replace the sump / motor pump / tub Damaged or defective The drain pump Replace the drain pump Drain hose was obstructed or snap Put the hose in the right way Defective pressure switch Replace the pressure switch Loose hose clamps Tighten or replace hose clamps Loose heater element Tighten heater element mounting nuts Loose sump Tighten the sump Loose axe of the lower spray arm Tighten the axe Loose softener Tighten the softener Damaged or defective wiring Repair the wiring Defective the electric control Replace the electric control The wiring be wrong connected with the microswitch after repair Right connected with the microswitch

Defective microswitch Replace the microswitch The float too high or something make the microswitch set Repair the float and microswitch

ERROR006(E6)

The NTC thermistor was damaged Replace thermistor The temperature is lower than -20°C Temperature should be higher than -20°C Damaged or defective wiring Repair wiring Defective electric control Replace electric control

ERROR007(E7)

NTC thermistor was damaged Replace thermistor Temperature is higher than 120 °C The temperature should be below than 120°C Damaged or defective wiring Repair wiring Defective electric control Replace electric control

Note: this model have no ERROR002 (E2) and ERROR005 (E5).

Troubleshooting

25

2. Malfunction Table

No. Symptom Malfunction Code Reference Solution

1 Malfunction1

1.1 No water fill in Connect the water pipe and open the water supply

1.2 Water pipe bending Put the water pipe at the right place 1.3 Inlet valve failure Replace it

1.4 Low water pressure Make sure the water pressure is ≥0.04MPa

1.5 Blocked inlet pipe or inlet valve Remove the inlet pipe and inlet valve for cleaning.

1.6 Circuitry malfunction or damage. Maintenance for the circuitry 1.7 Micro switch malfunction Replace it 1.8 Base buoy malfunction or is too dirty Replace or clean the base buoy

1.9 Too much water used at other places Use dishwasher when there’s not much water used at other places

1.10 Controller malfunction Replace it

2 Malfunction 2

2.1 Drain pump malfunction or damage Replace it 2.2 Drain pump is blocked or bended Put the drain pump at the right place 2.3 Micro switch malfunction Replace it 2.4 Base buoy malfunction or is too dirty Change or clean the base buoy 2.5 Controller malfunction Replace it 2.6 Wiring malfunction or damage Maintenance

3 Malfunction 3

3.1 Low voltage Make sure the voltage ≥198V

3.2 Thermostat2 damage or heating pipe fuse erosion

Replace the thermostat or heating pipe fuse

3.3 Wiring malfunction or damage Maintenance 3.4 Temperature control switch1 damage Replace it 3.5 Heating pipe damage Replace it 3.6 Controller malfunction Replace it 3.7 Motor low speed or stops to spin Replace the motor 3.8 The filter is blocked Clean the filter

3.9 The water level in the tub is not high enough

Check the pressure switch, inlet valve, flowmeter or the height of the drain pipe

3.10 The micro switch connecting to heating pipe is burned Replace the pressure switch

3.11 The pressure switch do not work

3.12 Heating pipe damage, or wiring is loosen

Replace heating pipe or check the wiring

3.13 Controller malfunction Replace the timer or PCB 3.14 Thermostat(thermistor) malfunction Replace the thermostat

4 Malfunction 4

4.1 Water leakage in the pressure switch or the connecting pipe

Reconnect the pipe, or replace a pressure switch

4.2 The flow meter terminal failure repair the flow meter terminal

4.3 Damaged the sump/ wash pump/tub/drain pump

Repair or replace the sump /wash pump /tub/drain pump

4.4 Defective pressure switch Replace the pressure switch 4.5 Loose hose clamps Tighten or replace hose clamps

26

4.6 Loose heater element Tighten heater element mounting nuts

4.7 Loose sump Tighten the sump 4.8 Loose axis of the lower spray arm Tighten the axis 4.9 Loose softener Tighten the softener

4.10 Damaged or defective wiring Repair the wiring 4.11 Defective the electric control Replace the electric control

4.12 The wiring be wrong connected with the micro switch after repair

Right connected with the micro switch

4.13 Defective micro switch Replace the micro switch

4.14 The float too high or something make the micro switch set Repair the float and micro switch

4.15 Drain hose was obstructed or snap Put the hose in the right way

5 Malfunction 5

5.1 Valve damage Replace it 5.2 Base buoy damage or is too dirty Replace or clean the base buoy 5.3 Wiring malfunction or damage Maintenance 5.4 Controller malfunction Replace it

6 Leaks of salt（ water softener installed）

6.1 The cover for water softener is loosen Tighten the cover

6.2 O sets reversal Replace it

7 Dishwasher do not work after pressing “start”

7.1 The door is not close properly Close the door properly 7.2 Door switch malfunction or damage Replace it 7.3 Latch malfunction or damage Replace it 7.4 Wiring malfunction or damage Maintenance 7.5 Controller malfunction Replace it 7.6 Controller is disturbed by the panel Replace the controller or panel

8

Inlet water can not stop, even when the electricity is off

8.1 Inlet valve malfunction Replace it

8.2 Soil deposits on the clapboard of the inlet valve

Remove the soil or replace the inlet valve

9 Inlet water can not stop, unless the electricity is off

9.1 Controller malfunction Replace it

10 Not much water fill in

10.1 The water pressure is too low Make sure the water pressure ≥0.03MPa

10.2 The pipe is bended Put the pipe at the right place 10.3 The sump or filter is blocked Clean the sump or filter 10.4 Micro switch malfunction Replace it 10.5 The dishwasher is not set Set the dishwasher

11 The dishwasher works when the door is open

11.1 Door switch malfunction or damage Replace it 11.2 Latch malfunction or damage Replace it 11.3 Wiring malfunction or damage Maintenance 11.4 Controller malfunction Replace it

12 The motor sounds but can not operate or spin

12.1 Motor bearing malfunction Replace the motor 12.2 Capacitor malfunction Replace it 12.3 Wiring malfunction or damage Maintenance 12.4 Voltage is not suitable for the motor Replace the motor

13 Motor overheating 13.1 Short circuit failure of the motor coil Replace the motor 13.2 Voltage is not suitable Replace the motor

27

13.3 Capacitor malfunction Replace the capacitor 13.4 Motor axis is stick totally Replace the motor

14 Washing cycle does not stop 14.1 Controller malfunction Replace it

15 Heating pipe fuse damage

15.1 Water drain up Make sure water drain up 15.2 Sump or filter is blocked Clean the sump or filter 15.3 Suds leak out Refer to the user manual 15.4 Not much water fill Refer to “not much water fill” 15.5 Thermostat switch malfunction Replace it 15.6 Wiring malfunction or damage Maintenance 15.7 Micro switch malfunction Replace it 15.8 Base buoy malfunction or is too dirty Replace or clean the base buoy 15.9 Controller malfunction Replace it

16 Water siphon 16.1 Drain pipe opening is too low Set the opening at a suitable height

16.2 No air gap Install an air intake at the top of the pipe

17 Spots left on the dishes 17.1 Use soft water (natural or man-made) Have water analyzed at related office

18 Spots and bluish film on the glasses

18.1 Detergent stays too long in the dispenser or too much detergent used Please refer to the user manual and

use the dishwasher properly 18.2 Dishes are not loaded properly

18.3 The soil left in the dishwasher is not disposed properly Please refer to the user manual

19 Motor pump assembly make noise

19.1 Soil left on the sump bottom Clean the sump and the space around it

19.2 Failed to install the pump assembly correctly

Check the pump and install it in the right way

19.3 Pump impeller can not fill the gap, or friction happens

Use deployed tool to install the filling gasket in the right place

20 Poor washing effect

20.1 The sump or filter is blocked Clean the sump or filter 20.2 The position of the filter is not right Maintain or replace the filter

20.3 Plates or other dishes stop the spray arm

Turn the spray arm before washing starts

20.4 Dishes are not loaded properly Please refer to the user manual and use the dishwasher properly

20.5 Not enough detergent

20.6 Not suitable washing cycle is selected

20.7 Detergent dispenser malfunction Replace it 20.8 Spray arm malfunction Clean or replace it 20.9 Not much water fill in Refer to malfunction 2 20.10 Pump malfunction Replace it 20.11 No salt in the water softener Refill the salt

21 Poor drying effect

21.1 Dishes are not loaded properly Please refer to the user manual and load the dishes properly 21.2 Not suitable washing cycle is

selected 21.3 Dispenser not working Replace it 21.4 The temperature of the rinsing water

is not high enough Replace the controller

21.5 Replace the NTC thermistor

CODIGOS DE ERROR

MODELO: DDW-M1211POS Part Code Descripción Qty FOTO 1 FOTO 2 FOTO 3

1001 673000900249 External pipe 1 $0,76

1002 NO DISPONIBLE O Ring I 31.5X3.55 2

1003 NO DISPONIBLE Guide casing 1

1004 NO DISPONIBLE External pipe nut 1

1005 673001900016 Water dispenser 1 $0,34

1006 673000300067 Upper sprayer 1 $2,52

1007 673000900089 Upper sprayer pipe 1 $0,10

1009 673001300041 Upper sprayer holder block 1 $0,02

1010 673002300002 Float holder 1 $0,09

1011 NO DISPONIBLE Screw ST2.9x22 1

1012 673002300003 Float 1 $0,04

1013 674000300053 Micro switch 1 $0,52

1016 673002500072 Micro filter 1 $0,66

1017 673001600008 Sump nut 1 $0,15

1018 673001500016 Sump gasket 1 $0,16

1019 673000700065 Sump 1 $1,12

1020 NO DISPONIBLE Clamp 12.7×1.8 1

1022 NO DISPONIBLE PVC hose 1

1027 674000600074 Drain pump 1 $5,79

1029 673002200043 Salt filler 1 $0,22

1030 673002800050 Softener cover assembly 1 $0,12

1031 673001700053 Softener cover gasket 1 $0,03

1032 673001600039 Softener nut 1 $0,04

1033 673001700001 Softener gasket 1 $0,06

1034 674000700021 Softener 1 $7,55

1036 NO DISPONIBLE Clamp 14.5×1.8 3

1037 NO DISPONIBLE Drain hose hook 1

1038 NO DISPONIBLE Drain hose holder 1

1039 673000900185 Drain hose 1 $1,92

1042 674000000198 Power cord 1 $2,60

1045 673000900270 Inlet hose assembly 1 $10,09

1046 673000900026 Regeneration hose 1 $0,30

1051 673001600002 Air breather nut 1 $0,02

1054 673002700005 Air breather assembly 1 $3,95

1064 673000300069 Lower sprayer 1 $2,49

1070 674000600041 Washing pump 1 $23,49

1073 673002400066 Motor insulation pan 1 $0,17

1074 673000900182 Connect hose 2 $0,09

1083 673000900045 Bend connect hose 1

1085 673001400025 Heating element support 1 $0,05

1086 674001100039 Heating elements 1 $9,51

1088 673001600024 Water inlet nut 1 $0,05

1089 673001500019 Water inlet gasket 1 $0,06

1091 673002600035 Water inlet 1 $0,20

1093 674000900038 Sensing device 1 $0,98

1113 673002500070 plane filter 1 $2,06

1114 673001300137 Scran collection 1 $0,31

1115 674000300079 Pressure switch 1 $2,57

1116 673001400083 power cord clasper 1 $0,03

1117 674000300067 switch assembly for heating 1 $1,96

2001 NO DISPONIBLE Door edge guard piece 2

2002 672002200079 Inner door 1 $16,79

2004 672001700011 Dispenser bracket 2 $0,11

2005 674000800039 Dispenser 1 $6,95

2006 674000100697 wiring assembly 1 $5,55

2008 NO DISPONIBLE Ring Φ6 4

2009 672001300029 Left gemel assembly 1 $1,59

2010 NO DISPONIBLE Dowel 2

2011 672001300030 Right gemel assembly 1 $1,59

2012 672001300024 Door gemel assembly 1 $2,02

2013 672000100000 Door spring 2 $0,16

2014 672001100001 Door spring bolt 2

2017 672001800306 Outer door 1

2018 673005100541 Control panel 1 $2,22

2023 673001800135 Handle assembly 1 $1,09

2027 674000300065 Power switch 1 $0,87

2028 NO DISPONIBLE Red pilot lamp 1

2033 NO DISPONIBLE Indicator cover 9

2034 + 2036 674001030000 Control board as 1 $18,50

2036 673002400095 Control board box 1

2039 NO DISPONIBLE Window 1

2950 673000800584 Power button 1 $0,02

2951 673000800598 Program key 1 $0,02

2952 673000800599 Start/Pause key 1 $0,02

2954 NO DISPONIBLE delay key 1

2957 NO DISPONIBLE Half load key 1

3001 NO DISPONIBLE Left side panel 1

3002 NO DISPONIBLE Back cover board 1

3003 NO DISPONIBLE Upright left assembly 1

3004 673000200051 Ceiling board 1 $10,48

3005 NO DISPONIBLE Upper rear crosspiece 1

3006 673001300061 door clamp 1 $0,06

3007 672001400034 Door lock 1 $0,17

3008 673001300003 Top clamp block 2 $0,02

3009 NO DISPONIBLE Upper front crosspiece 1

3010 673001700057 Tank gasket 1 $1,92

3011 NO DISPONIBLE Upright right assembly 1

3012 NO DISPONIBLE Right panel 1

3013 673001300102 Upper basket cup holder 4 $0,23

3017 672000800210 Lower basket 1 $8,63

3018 672000800209 Upper basket 1 $10,29

3020 673001100024 Right washboard 1 $0,19

3021 673001300066 Rail block 2 $0,02

3022 672001700001 Rail 1 $0,73

3023 673001400049 Rail support assembly 4

3024 673001100019 Washboard 1 $1,06

3026 NO DISPONIBLE Feet support assembly 2

3027 NO DISPONIBLE Lower front crosspiece 1

3029 NO DISPONIBLE Tray assembly 1

3030 673001100023 Left side baseboard 1 $0,19

3033 NO DISPONIBLE Lower rear crosspiece 1

3034 NO DISPONIBLE Middle rear crosspiece 1

3035 673002200079 Measurable spoon 1 $0,04

3039 NO DISPONIBLE Orientation pole 1

3079 673002200091 3 in 1 tablet container 1 $0,13

1035+1047 673000900224 Softener pipe 2 $0,24

1071+1072 672000200054 Washing motor support 1 $0,37

3014 673002200055 Cutlery basket 1 $0,99

3025-a 673001100180 Adjustable foot （front） 2 $0,25

3025-b 673001100156 Adjustable foot(back) 2 $0,13

C5004 673006200004 Rinsing agent cup 1 $0,08

OTK 175 NO DISPONIBLE OTK 175 2



OTK 310 672000700001 OTK 310 6 $0,07

OTK 396 672000700007 OTK 396 2 $0,07

LAVAVAJILLAS · panel features, please see user manual of model you service. 1 Power Button and...

Documents

Transcript of LAVAVAJILLAS · panel features, please see user manual of model you service. 1 Power Button and...