Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY ...
Transcript of Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY ...
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
Permanent Facility
1 ELECTRO-
TECHNICAL-
ALTERNATING
CURRENT (< 1 GHZ)
(Measure)
AC Current 50 Hz 100 m A to 10 A 0.6% to 0.7% Using 6 ½ DMM Fluke
8846A by Direct
measure
2 ELECTRO-
TECHNICAL-
ALTERNATING
CURRENT (< 1 GHZ)
(Measure)
AC Current 50 Hz 100 m A to 10 A 0.6% to 0.7% Using 6 ½ DMM Fluke
8846A by Direct
measure
3 ELECTRO-
TECHNICAL-
ALTERNATING
CURRENT (< 1 GHZ)
(Measure)
AC Current 50 Hz 100 micro A to 100 mA 2.0% to 0.6% Using 6 ½ DMM Fluke
8846A by Direct
measure
4 ELECTRO-
TECHNICAL-
ALTERNATING
CURRENT (< 1 GHZ)
(Measure)
AC Current 50 Hz 100 micro A to 100 mA 2.0% to 0.6% Using 6 ½ DMM Fluke
8846A by Direct
measure
5 ELECTRO-
TECHNICAL-
ALTERNATING
CURRENT (< 1 GHZ)
(Measure)
AC Voltage50 Hz 1 V to 1000 V 0.5% to 0.11% Using 6 ½ DMM Fluke
8846A by Direct
measure
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 1 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
6 ELECTRO-
TECHNICAL-
ALTERNATING
CURRENT (< 1 GHZ)
(Measure)
AC Voltage50 Hz 10 mV to 100 mV 1.5% to 0.5% Using 6 ½ DMM Fluke
8846A by Direct
measure
7 ELECTRO-
TECHNICAL-
ALTERNATING
CURRENT (< 1 GHZ)
(Measure)
High Voltage 50Hz 1 kV to 5 kV 4.0% Using Motwane HV
Probe with DMM
motwane by Direct
measure
8 ELECTRO-
TECHNICAL-
ALTERNATING
CURRENT (< 1 GHZ)
(Source)
AC Current 50Hz to
1kHz
1 A to 10 A 0.16% to 0.15% Using Multifunction
calibrator 5500A Fluke
by Direct Method
9 ELECTRO-
TECHNICAL-
ALTERNATING
CURRENT (< 1 GHZ)
(Source)
AC Current 50Hz to
1kHz
100 micro A to 1 A 0.45% to 0.16% Using Multifunction
calibrator 5500A Fluke
by Direct Method
10 ELECTRO-
TECHNICAL-
ALTERNATING
CURRENT (< 1 GHZ)
(Source)
AC Current 50Hz to
1kHz
100 micro A to 1 A 0.45% to 0.16% Using Multifunction
calibrator 5500A Fluke
by Direct Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 2 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
11 ELECTRO-
TECHNICAL-
ALTERNATING
CURRENT (< 1 GHZ)
(Source)
AC Power @50HzAt
UPF to 0.2 PF
0.5 (1V, 0.5A , UPF to
0.2 Lag)@ 50Hz 0.5W
Watt to 6 ( 600V,10 A,
UPF to 0.2 Lag)@
50Hz Watt
0.5% to 2.0% Using Multifunction
calibrator 5500A Fluke
by Direct Method
12 ELECTRO-
TECHNICAL-
ALTERNATING
CURRENT (< 1 GHZ)
(Source)
AC Power @50HzAt
UPF to 0.2 PF
0.5 (1V, 0.5A , UPF to
0.2 Lag)@ 50Hz 0.5W
Watt to 6 ( 600V,10 A,
UPF to 0.2 Lag)@
50Hz Watt
0.5% to 2.0% Using Multifunction
calibrator 5500A Fluke
by Direct Method
13 ELECTRO-
TECHNICAL-
ALTERNATING
CURRENT (< 1 GHZ)
(Source)
AC Voltage 50Hz to
1kHz
10 mV to 10 V 0.45% to 0.06% Using multifunction
calibrator 5500A Fluke
by Direct Method
14 ELECTRO-
TECHNICAL-
ALTERNATING
CURRENT (< 1 GHZ)
(Source)
AC Voltage 50Hz to
1kHz
10 V to 1000 V 0.06% to 0.1% Using Multifunction
calibrator 5500A Fluke
by Direct Method
15 ELECTRO-
TECHNICAL-
ALTERNATING
CURRENT (< 1 GHZ)
(Source)
Phase Angle 0 ° to 90 ° 0.19° Using multifunction
calibrator 5500A Fluke
by Direct Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 3 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
16 ELECTRO-
TECHNICAL-
ALTERNATING
CURRENT (< 1 GHZ)
(Source)
Power Factor 0.2 PF to 1 PF 0.17PF Using Multifunction
calibrator 5500A Fluke
by Direct Method
17 ELECTRO-
TECHNICAL- DIRECT
CURRENT (Measure)
DC Current 10 micro A to 10 A 0.7% to 0.2% Using 6 1/2 DMM Fluke
8846A by Direct
measure
18 ELECTRO-
TECHNICAL- DIRECT
CURRENT (Measure)
DC High Voltage 1 kV to 5 kV 2% Using motwane HV
probe with DMM
motwane by direct
measure
19 ELECTRO-
TECHNICAL- DIRECT
CURRENT (Measure)
DC Voltage 1 mV to 100 mV 1.00% to 0.045% Using 6 1/2 DMM Fluke
8846A / Direct Measure
20 ELECTRO-
TECHNICAL- DIRECT
CURRENT (Measure)
DC Voltage 100 mV to 1000 V 0.045% to 0.04% Using 6 1/2 DMM Fluke
8846A / Direct Measure
21 ELECTRO-
TECHNICAL- DIRECT
CURRENT (Measure)
Low Resistance 1 m ohm to 10 ohm 1.1% Using 6.5 Digit DMM
and fluke 5500A by V/ I
method.
22 ELECTRO-
TECHNICAL- DIRECT
CURRENT (Measure)
Resistance 10 ohm to 100 k ohm 0.7% to 0.2% Using 6 ½ DMM Fluke
8846A by Direct
measure
23 ELECTRO-
TECHNICAL- DIRECT
CURRENT (Measure)
Resistance 100 k ohm to 100 M
ohm
0.2% to 2.4% Using 6 ½ DMM Fluke
8846A by Direct
measure
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 4 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
24 ELECTRO-
TECHNICAL- DIRECT
CURRENT (Measure)
Resistance 100 M ohm to 1 G ohm 2.9% Using 6 ½ DMM Fluke
8846A by Direct
measure
25 ELECTRO-
TECHNICAL- DIRECT
CURRENT (Source)
DC Current 10 micro A to 100
micro A
0.6% to 0.07% Using multifunction
calibrator 5500A Fluke
by Direct sourcing
26 ELECTRO-
TECHNICAL- DIRECT
CURRENT (Source)
DC Current 100 mA to 10 A 0.02% to 0.09% Using multifunction
calibrator 5500A Fluke
by Direct sourcing
27 ELECTRO-
TECHNICAL- DIRECT
CURRENT (Source)
DC Current 100 micro A to 100 mA 0.07% to 0.02% Using multifunction
calibrator 5500A Fluke
by Direct sourcing
28 ELECTRO-
TECHNICAL- DIRECT
CURRENT (Source)
DC Voltage 1 mV to 10 mV 1.0% to 0.1% Using Multifunction
calibrator 5500A Fluke
by Direct sourcing
29 ELECTRO-
TECHNICAL- DIRECT
CURRENT (Source)
DC Voltage 1 V to 1000 V 0.015% to 0.01% Using Multifunction
calibrator 5500A Fluke
by Direct sourcing
30 ELECTRO-
TECHNICAL- DIRECT
CURRENT (Source)
DC Voltage 10 mV to 1 V 0.1% to 0.015% Using Multifunction
calibrator 5500A Fluke
by Direct sourcing
31 ELECTRO-
TECHNICAL- DIRECT
CURRENT (Source)
Resistance 1 m ohm to 10 ohm 1.35% to 2.4% Using shunts & Decade
Box Maxwell, Model
DR 8 Direct sourcing
32 ELECTRO-
TECHNICAL- DIRECT
CURRENT (Source)
Resistance 10 M ohm to 100 M
ohm
0.08% to 0.6% Using Multifunction
calibrator 5500 A Fluke
by Direct sourcing
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 5 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
33 ELECTRO-
TECHNICAL- DIRECT
CURRENT (Source)
Resistance 10 ohm to 100 k ohm 0.2% to 0.02% Using Multifunction
calibrator 5500 A Fluke
by Direct sourcing
34 ELECTRO-
TECHNICAL- DIRECT
CURRENT (Source)
Resistance 100 k ohm to 10 M ohm 0.02% to 0.08% Using Multifunction
calibrator 5500 A Fluke
by Direct sourcing
35 ELECTRO-
TECHNICAL- DIRECT
CURRENT (Source)
Resistance 100 M ohm to 300 M
ohm
0.6% to 1.0% Using Multifunction
calibrator 5500 A Fluke
by Direct sourcing
36 ELECTRO-
TECHNICAL- DIRECT
CURRENT (Source)
Resistance 300 M ohm to 100 G
ohm
3.4% Using Mega Ohm Box
Maxwell, Model DB 231
for calibration of
Meggers upto 5kV by
Direct method
37 ELECTRO-
TECHNICAL- OTHERS
(Measure)
Counter Meter 0 Count to 999999
Count
1.7% to 1% Using Stop Watch and
Fluke Multifunction
calibrator 5500A
38 ELECTRO-
TECHNICAL-
TEMPERATURE
SIMULATION
(Measure)
B type Thermocouples 600 ° C to 1750 ° C 0.75° C Using Radix / Fluke
Multifunction calibrator
by Simulation method
39 ELECTRO-
TECHNICAL-
TEMPERATURE
SIMULATION
(Measure)
E type Thermocouple -200 ° C to 1000 ° C 0.44° C Using Radix / Fluke
Multifunction calibrator
by Simulation method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 6 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
40 ELECTRO-
TECHNICAL-
TEMPERATURE
SIMULATION
(Measure)
J type Thermocouple -200 °C to 750 °C 0.2°C Using Radix / Fluke
Multifunction calibrator
by Simulation method
41 ELECTRO-
TECHNICAL-
TEMPERATURE
SIMULATION
(Measure)
K type Thermocouple -200 °C to 1350 °C 0.25°C Using Radix / Fluke
Multifunction calibrator
by Simulation method
42 ELECTRO-
TECHNICAL-
TEMPERATURE
SIMULATION
(Measure)
N type Thermocouple 50 °C to 1750 °C 0.75°C Using Radix / Fluke
Multifunction calibrator
by Simulation method
43 ELECTRO-
TECHNICAL-
TEMPERATURE
SIMULATION
(Measure)
R type Thermocouple 50 °C to 1750 °C 0.41°C Using Radix / Fluke
Multifunction calibrator
by Simulation method
44 ELECTRO-
TECHNICAL-
TEMPERATURE
SIMULATION
(Measure)
RTD -200 °C to 800 °C 0.35°C Using Radix / Fluke
Multifunction calibrator
by Simulation method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 7 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
45 ELECTRO-
TECHNICAL-
TEMPERATURE
SIMULATION
(Measure)
S type Thermocouple 50 °C to 1750 °C 0.70°C Using Radix / Fluke
Multifunction calibrator
by Simulation method
46 ELECTRO-
TECHNICAL-
TEMPERATURE
SIMULATION
(Measure)
T type Thermocouple -200 °C to 400 °C 0.27°C Using Radix / Fluke
Multifunction calibrator
by Simulation method
47 ELECTRO-
TECHNICAL-
TEMPERATURE
SIMULATION (Source)
B type Thermocouple 600 ° C to 1750 ° C 0.75° C Using Radix / Fluke
Multifunction calibrator
by Simulation method
48 ELECTRO-
TECHNICAL-
TEMPERATURE
SIMULATION (Source)
E type Thermocouples -200 ° C to 1000 ° C 0.75° C Using Radix / Fluke
Multifunction calibrator
by Simulation method
49 ELECTRO-
TECHNICAL-
TEMPERATURE
SIMULATION (Source)
J type Thermocouples -200 °C to 750 °C 0.75°C Using Radix / Fluke
Multifunction calibrator
by Simulation method
50 ELECTRO-
TECHNICAL-
TEMPERATURE
SIMULATION (Source)
K type Thermocouples -200 °C to 1350 °C 0.75°C Using Radix / Fluke
Multifunction calibrator
by Simulation method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 8 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
51 ELECTRO-
TECHNICAL-
TEMPERATURE
SIMULATION (Source)
N type Thermocouples 50 °C to 1750 °C 0.75°C Using Radix / Fluke
Multifunction calibrator
by Simulation method
52 ELECTRO-
TECHNICAL-
TEMPERATURE
SIMULATION (Source)
R type Thermocouples 50 °C to 1750 °C 0.75°C Using Radix / Fluke
Multifunction calibrator
by Simulation method
53 ELECTRO-
TECHNICAL-
TEMPERATURE
SIMULATION (Source)
RTD -200 °C to 800 °C 0.35°C Using Radix / Fluke
Multifunction calibrator
by Simulation method
54 ELECTRO-
TECHNICAL-
TEMPERATURE
SIMULATION (Source)
S type Thermocouples 50 °C to 1750 °C 0.75°C Using Radix / Fluke
Multifunction calibrator
by Simulation method
55 ELECTRO-
TECHNICAL-
TEMPERATURE
SIMULATION (Source)
T type Thermocouples -200 °C to 400 °C 0.75°C Using Radix / Fluke
Multifunction calibrator
by Simulation method
56 ELECTRO-
TECHNICAL- TIME &
FREQUENCY
(Measure)
Capacitance 1kHz 1 nF to 100 micro F 3% to 0.7% Using 6 ½ DMM Fluke
8846A by Direct
measure
57 ELECTRO-
TECHNICAL- TIME &
FREQUENCY
(Measure)
Capacitance 1kHz 100 micro F to 300
micro F
0.7% to 1.2% Using 6 ½ DMM Fluke
8846A by Direct
measure
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 9 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
58 ELECTRO-
TECHNICAL- TIME &
FREQUENCY
(Measure)
Capacitance 1kHz 100 micro F to 300
micro F
0.7% to 1.2% Using 6 ½ DMM Fluke
8846A by Direct
measure
59 ELECTRO-
TECHNICAL- TIME &
FREQUENCY
(Measure)
Digital / Analog Stop
Watch / Timer
10 sec to 59 min 1.51sec to 2sec Using Digital Time
interval meter by
Comparison Method
60 ELECTRO-
TECHNICAL- TIME &
FREQUENCY
(Measure)
Frequency 10 Hz to 1 M Hz 0.8%% to 1.40% Using 6 ½ DMM Fluke
8846A by Direct
measure
61 ELECTRO-
TECHNICAL- TIME &
FREQUENCY (Source)
Capacitance 1kHz 0.5 n F to 100 micro F 3% to 0.7% Using Multifunction
calibrator 5500A Fluke
by Direct Method
62 ELECTRO-
TECHNICAL- TIME &
FREQUENCY (Source)
Capacitance 1kHz 100 micro F to 300
micro F
0.7% to 1.2% Using Multifunction
calibrator 5500A Fluke
by Direct Method
63 ELECTRO-
TECHNICAL- TIME &
FREQUENCY (Source)
Frequency 10 Hz to 100 k Hz 0.015% to 0.065% Using Multifunction
calibrator 5500A Fluke
by Direct Method
64 MECHANICAL-
ACCELERATION AND
SPEED
Tachometer / RPM 1000 to 20000 rpm 0.35% Using Non contact
Tachometer &
Mechanical Tacho-
generator
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 10 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
65 MECHANICAL-
ACCELERATION AND
SPEED
Tachometer / RPM up to 1000 rpm 0.38% Using Non contact
Tachometer &
Mechanical Tacho-
generator
66 MECHANICAL-
ACOUSTICS
Sound Level Meter 1 kHz 94dB to 1 kHz
114dB
0.85 dB Using Sound level
calibrator
67 MECHANICAL-
DENSITY AND
VISCOSITY
Hydrometer 0.7 sp.gr. to 1.0 sp.gr. 0.0012 sp. gr. Using Standard
Hydrometer
68 MECHANICAL-
DENSITY AND
VISCOSITY
Hydrometer 1.0 sp. gr. to 1.8 sp. gr. 0.0016 sp.gr. Using Standard
Hydrometer
69 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Ball Type Micrometer
L.C. 0.001 mm
0 to 25 mm 2 µm Using Slip Gauge Set
Grade 0
70 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Bevel Protractor L.C. 5
Min
0 to 360 deg 1.5 min Using Angle Gauge
Block & Surface Plate
71 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Calipers
(Vernier/Dial/Digital)
L.C. 0.01 mm
0 to 1000 mm 18µm Using Caliper Checker
& Length Bar Set, Slip
Gauge Set
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 11 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
72 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Calipers
(Vernier/Dial/Digital)
L.C. 0.01 mm
0 to 300 mm 13 µm Using Caliper Checker
& Length Bar Set, Slip
Gauge Set
73 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Calipers
(Vernier/Dial/Digital)
L.C. 0.01 mm
0 to 600 mm 13µm Using Caliper Checker
& Length Bar Set, Slip
Gauge Set
74 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Calipers
(Vernier/Dial/Digital)
L.C. 0.02 mm
0 to 2000 mm 25µm Using Caliper Checker
& Length Bar Set, Slip
Gauge Set
75 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Depth Gauge
(Vernier/Dial/Digital)
L.C. 0.01 mm
0 to 300 mm 10.3µm Using Slip Gauge Set ,
Length Bar Set &
Surface Plate
76 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Depth Micrometer L.C.
0.001 mm
0 to 300 mm 9µm Using Slip Gauge Set &
Length Bar Set ,
Surface Plate
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 12 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
77 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Dial Thickness Gauge
L.C. 0.001 mm
0 to 25 mm 2µm Using Slip Gauge Set
Grade 0
78 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
External Micrometer
L.C. 0.001 mm
0 to 100 mm 4µm Using Slip Gauge Set /
Length Bar Set
79 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
External Micrometer
L.C. 0.001 mm
100 to 300 mm 7µm Using Slip Gauge Set /
Length Bar Set
80 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
External Micrometer
L.C. 0.01 mm
500 to 1000 mm 12µm Using Slip Gauge Set /
Length Bar Set
81 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
External Micrometer
L.C. 0.010 mm
300 to 500 mm 9µm Using Slip Gauge Set /
Length Bar Set
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 13 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
82 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Feeler / Leaf Gauge up to to 2 mm 3µm Using Comparator
Stand with Digital Dial
83 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Height Gauge
(Vernier/Dial/Digital)
L.C. 0.01 mm
0 to 1000 mm 15.1µm Using Caliper Checker
/ Length Bar Set &
Surface Plate
84 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Height Gauge
(Vernier/Dial/Digital)
L.C. 0.01 mm
0 to 300 mm 12µm Using Caliper Checker
/ Length Bar Set &
Surface Plate
85 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Height Gauge
(Vernier/Dial/Digital)
L.C. 0.01 mm
0 to 600 mm 12µm Using Caliper Checker
/ Length Bar Set &
Surface Plate
86 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Internal Micrometer
(Extension Rods)
50 to 100 mm 4µm Using Slip Gauge Set,
Length Bar &
Comparator Stand with
Digital Dial
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 14 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
87 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Internal Micrometer
L.C. 0.01 mm
5 to 300 mm 7µm Using Slip Gauge Set,
Length Bar &
Comparator Stand with
Digital Dial
88 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Internal Micrometer
L.C. 0.01 mm
50 to 1000 mm 10µm Using Slip Gauge Set,
Length Bar &
Comparator Stand with
Digital Dial
89 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Lever Dial Gauge L.C.
0.01 mm
upto to 1.6 mm 6µm Using Dial Calibration
Tester
90 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Lever Dial Gauge
L.C.0.001 mm
upto to 1.0 mm 2µm Using Dial Calibration
Tester
91 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Measuring Pin 0.1 to 20 mm 1.2µm Using Comparator
Stand with Digital Dial
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 15 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
92 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Measuring Scale L.C. 1
mm
upto to 1000 mm 117µm Using Steel Scale /
Tape Calibrator
93 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Measuring Tape / Pi-
Tape
0 to 50 meter 117vL µm L in mtr Using Steel Tape /
Tape calibrator L.C. 1
mm
94 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Micrometer Setting
Standard
> 25 to 100 mm 1.8µm Using Comparator
Stand with Digital Dial,
Slip Gauges and
Length Bar
95 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Micrometer Setting
Standard
>100 to 300 mm 4µm Using Comparator
Stand with Digital Dial,
Slip Gauges and
Length Bar
96 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Micrometer Setting
Standard
>300 to 500 mm 6µm Using Comparator
Stand with Digital Dial,
Slip Gauges and
Length Bar
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 16 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
97 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Micrometer Setting
Standard
>500 to 975 mm 9µm Using Comparator
Stand with Digital Dial,
Slip Gauges and
Length Bar
98 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Pin Pointed Micrometer
L.C. 0.001 mm
0 to 25 mm 2µm Using Slip Gauge Set
Grade 0
99 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Pistol Caliper L.C. 0.1
mm
upto to 100 mm 75µm Using Slip Gauge Set
100 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Plain Plug Gauge /
Width Gauge / Height
Setting Block
> 100 to 250 mm 3µm Using Comparator
Stand with Digital Dial
& Slip Gauge Set
101 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Plain Plug Gauge /
Width Gauge / Height
Setting Block
3 to 100 mm 3µm Using Comparator
Stand with Digital Dial
& Slip Gauge Set
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 17 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
102 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Plunger Dial Gauge
L.C. 0.001 mm
upto to 25 mm 4µm Using Dial Calibration
Tester, Slip Gauge Set
103 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Plunger Dial Gauge
L.C. 0.01 mm
upto to 50 mm 5.9µm Using Dial Calibration
Tester, Slip Gauge Set
104 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Snap Gauge >100 to 250 mm 3µm Using Slip Gauge Set &
Feeler Gauge
105 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Snap Gauge 2 to 100 mm 3µm Using Slip Gauge Set &
Feeler Gauge
106 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Spirit Level Sensitivity
0.01 mm/m
± 1 mm 9 µm/m Using Surface plate &
Tilting fixture and
Digital Dial Gauge
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 18 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
107 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Surface Plate 3000 to 3000 mm 3 µm Using Spirit Level
108 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Thickness Foils 0.005 to 2 mm 1.5µm Using Comparator
Stand with Digital Dial
109 MECHANICAL-
PRESSURE
INDICATING DEVICES
Hydraulic Pressure
Gauge / Digital /
Analog Pressure
Gauge / Pressure
Indicator
0 bar to 30 bar 0.8% of rdg to 0.8% of
rdg
Using Digital Pressure
Gauge
110 MECHANICAL-
PRESSURE
INDICATING DEVICES
Hydraulic Pressure
Gauge / Digital /
Analog Pressure
Gauge / Pressure
Indicator
30 bar to 600 bar 0.8% of rdg to 0.8% of
rdg
Using digital pressure
gauge
111 MECHANICAL-
PRESSURE
INDICATING DEVICES
Vacuum Gauge /
Indicator
(-) 0.9 bar to 0 bar 0.8% of rdg to 0.8% of
rdg
Using Digital Vacuum
Gauge by Direct
Comparison DKD-R-6-
1
112 MECHANICAL-
VOLUME
Glasswares - Pipette,
Burette, Measuring
Cylinder, Volumetric
Flask, Conical Flask
10 ml to 1000 ml 0.05ml Using Standard E1
Class Weights and
Micro Balance, L.C.
0.01 mg
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 19 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
113 MECHANICAL-
VOLUME
Glasswares - Pipette,
Burette, Measuring
Cylinder, Volumetric
Flask, Conical Flask
100 microlitre to 10 ml 0.34 microlitre Using Standard E1
Class Weights with
Micro Balance , L.C.
0.01 g
114 MECHANICAL-
VOLUME
Glasswares - Pipette,
Burette, Measuring
Cylinder, Volumetric
Flask, Conical Flask
1000 ml to 2000 ml 0.05ml Using Standard F2
Class Weights above
200 g with Micro
Balance, L.C. 0.1 mg
115 MECHANICAL-
VOLUME
Micro Pipette 10 microlitre to 100
microlitre
0.25 microlitre Using Standard E1
class Weights with
micro balance, L.C.
0.01 mg
116 MECHANICAL-
VOLUME
Micro Pipette 100 microlitre to 1000
µl
0.34 microlitre Using Standard E1
class Weights with
micro balance, L.C.
0.01 mg
117 MECHANICAL-
WEIGHING SCALE
AND BALANCE
Electronic Weighing
Balance
5g to 80 g 0.03mg Using Standard E1
Class Weights
118 MECHANICAL-
WEIGHING SCALE
AND BALANCE
Electronic Weighing
Balance
>300g to 3kg 40mg Using Standard F2
Class Weights L.C. 0.1
g
119 MECHANICAL-
WEIGHING SCALE
AND BALANCE
Electronic Weighing
Balance
>3kg to 30kg 2g Using F2 Class
Weights L.C. 1 g
120 MECHANICAL-
WEIGHING SCALE
AND BALANCE
Electronic Weighing
Balance
80g to 200 g 0.3mg Using Standard E1
Class Weights
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 20 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
121 MECHANICAL-
WEIGHING SCALE
AND BALANCE
Electronic Weighing
Balance
up to 5g 0.03mg Using Standard E1
Class Weights
122 MECHANICAL-
WEIGHING SCALE
AND BALANCE
Spring Balance 30kg 20g Using F2 class
Weights, L.C. 1 g
123 MECHANICAL-
WEIGHTS
Using weights M1 class
and coarser
1 mg to 10 mg 0.01 mg Using standard E1
class weights with
micro balance
124 MECHANICAL-
WEIGHTS
Weight F1 class and
Coarser
100 g 0.09mg Using Standard E1
Class weights with
micro balance
125 MECHANICAL-
WEIGHTS
Weight M1 class and
Coarser
500 g 6mg Using Standard F2
Class Weights with
micro balance
126 MECHANICAL-
WEIGHTS
weight, M1 Class and
crosser
10kg 74mg Using Standard F2
Class weights with
micro balance
127 MECHANICAL-
WEIGHTS
Weights E2 class and
Coarser
200 g 0.10mg Using Standard E1
Class weights with
micro balance
128 MECHANICAL-
WEIGHTS
Weights E2 class and
Coarser
50 g 0.03 mg Using Standard E1
Class weights with
micro balance
129 MECHANICAL-
WEIGHTS
Weights F1 class and
Coarser
1g to 20g 0.03mg Using Standard E1
Class weights with
micro balance
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 21 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
130 MECHANICAL-
WEIGHTS
Weights F1 class and
Coarser
20mg to 500mg 0.01mg Using Standard E1
Class weights with
micro balance
131 MECHANICAL-
WEIGHTS
Weights M1 class and
Coarser
1 kg 9 mg Using Standard F2
Class Weights with
micro balance
132 MECHANICAL-
WEIGHTS
Weights M1 class and
Coarser
2 kg 13 mg Using Standard F2
Class Weights with
micro balance
133 MECHANICAL-
WEIGHTS
Weights M1 class and
Coarser
5 kg 68mg Using Standard F2
Class Weights with
micro balance
134 THERMAL- SPECIFIC
HEAT & HUMIDITY
Humidity Meter with in
Built or external sensor,
Thermo- Hygrometer
20% RH to 95% RH @
25 degree C
1.9 % RH Using digital
Hygrometer and
Humidity generator with
chamber
135 THERMAL-
TEMPERATURE
Liquid in Glass
Thermometer, Dial /
Digital Thermometer ,
RTD / Thermocouple
with or without
Temperature Indicator
>25 degree C to 80
degree C
0.27 degree C Using Fluke RTD (Pt
100), 6 1/2 DMM &
Fluke Dry Well / Liquid
Baths
136 THERMAL-
TEMPERATURE
Liquid in Glass
Thermometer, Dial /
Digital Thermometer ,
RTD / Thermocouple
with or without
Temperature Indicator
>80 degree C to 300
degree C
0.27 degree C Using Fluke RTD (Pt
100), 6 1/2 DMM &
Fluke Dry Well / Liquid
Baths
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 22 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
137 THERMAL-
TEMPERATURE
Liquid in Glass
Thermometer, Dial /
Digital Thermometer ,
RTD / Thermocouple
with or without
Temperature Indicator
-30 degree C to 25
degree C
0.30 degree C Using Fluke RTD (Pt
100), 6 1/2 DMM &
Fluke Dry Well / Liquid
Baths
138 THERMAL-
TEMPERATURE
Thermocouple With or
Without Temperature
Indicator
300 degree C to 1000
degree C
1.9 degree C Using S type
Thermocouple, 6 1/2
DMM & Tubular
Furnace
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 23 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
Site Facility
1 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Current 50 Hz 100 m A to 10 A 0.6% to 0.7% Using 6 ½ DMM Fluke8846A by Directmeasure
2 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Current 50 Hz 100 m A to 10 A 0.6% to 0.7% Using 6 ½ DMM Fluke8846A by Directmeasure
3 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Current 50 Hz 100 micro A to 100 mA 2.0% to 0.6% Using 6 ½ DMM Fluke8846A by Directmeasure
4 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Current 50 Hz 100 micro A to 100 mA 2.0% to 0.6% Using 6 ½ DMM Fluke8846A by Directmeasure
5 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC High Voltage 1 kV to 100 kV 2.8% Using High VoltageDivider with kV meterMake – Udeyraj byDirect/ Comparisonmethod
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 24 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
Site Facility
6 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Voltage50 Hz 1 V to 1000 V 0.5% to 0.11% Using 6 ½ DMM Fluke8846A by Directmeasure
7 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Voltage50 Hz 10 mV to 100 mV 1.5% to 0.5% Using 6 ½ DMM Fluke8846A by Directmeasure
8 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
High Voltage 50Hz 1 kV to 20 kV 4.2% Using Motwane HVProbe with DMMmotwane By Directmeasure
9 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
AC Current 50Hz to1kHz
1 A to 10 A 0.16% to 0.15% Using Multifunctioncalibrator 5500A Flukeby Direct Method
10 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
AC Current 50Hz to1kHz
100 micro A to 1 A 0.45% to 0.16% Using Multifunctioncalibrator 5500A Flukeby Direct Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 25 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
Site Facility
11 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
AC Current 50Hz to1kHz
100 micro A to 1 A 0.45% to 0.16% Using Multifunctioncalibrator 5500A Flukeby Direct Method
12 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
AC Power @50HzAtUPF to 0.2 PF
0.5 (1V, 0.5A , UPF to0.2 Lag)@ 50Hz 0.5WWatt to 6 ( 600V,10 A,UPF to 0.2 Lag)@50Hz Watt
0.5% to 2.0% Using Multifunctioncalibrator 5500A Flukeby Direct Method
13 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
AC Power @50HzAtUPF to 0.2 PF
0.5 (1V, 0.5A , UPF to0.2 Lag)@ 50Hz 0.5WWatt to 6 ( 600V,10 A,UPF to 0.2 Lag)@50Hz Watt
0.5% to 2.0% Using Multifunctioncalibrator 5500A Flukeby Direct Method
14 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
AC Voltage 50Hz to1kHz
10 mV to 10 V 0.45% to 0.06% Using multifunctioncalibrator 5500A Flukeby Direct Method
15 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
AC Voltage 50Hz to1kHz
10 V to 1000 V 0.06% to 0.1% Using Multifunctioncalibrator 5500A Flukeby Direct Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 26 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
Site Facility
16 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Phase Angle 0 ° to 90 ° 0.19° Using multifunctioncalibrator 5500A Flukeby Direct Method
17 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Power Factor 0.2 PF to 1 PF 0.17PF Using Multifunctioncalibrator 5500A Flukeby Direct Method
18 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
DC Current 10 micro A to 10 A 0.7% to 0.2% Using 6 1/2 DMM Fluke8846A by Directmeasure
19 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
DC High Voltage 1 kV to 5 kV 2% Using motwane HVprobe with DMMmotwane by directmeasure
20 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
DC High Voltage 1 kV to 70 kV 2.0% Using High VoltageDivider with kV meter .Make – Udeyraj byDirect/ Comparisonmethod
21 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
DC Voltage 1 mV to 100 mV 1.00% to 0.045% Using 6 1/2 DMM Fluke8846A / Direct Measure
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 27 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
Site Facility
22 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
DC Voltage 100 mV to 1000 V 0.045% to 0.04% Using 6 1/2 DMM Fluke8846A / Direct Measure
23 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Low Resistance 1 m ohm to 10 ohm 1.1% Using 6.5 Digit DMMand fluke 5500A by V/ Imethod.
24 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Resistance 10 ohm to 100 k ohm 0.7% to 0.2% Using 6 ½ DMM Fluke8846A by Directmeasure
25 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Resistance 100 k ohm to 100 Mohm
0.2% to 2.4% Using 6 ½ DMM Fluke8846A by Directmeasure
26 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Resistance 100 M ohm to 1 G ohm 2.9% Using 6 ½ DMM Fluke8846A by Directmeasure
27 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
DC Current 10 micro A to 100micro A
0.6% to 0.07% Using multifunctioncalibrator 5500A Flukeby Direct sourcing
28 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
DC Current 100 mA to 10 A 0.02% to 0.09% Using multifunctioncalibrator 5500A Flukeby Direct sourcing
29 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
DC Current 100 micro A to 100 mA 0.07% to 0.02% Using multifunctioncalibrator 5500A Flukeby Direct sourcing
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 28 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
Site Facility
30 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
DC Voltage 1 mV to 10 mV 1.0% to 0.1% Using Multifunctioncalibrator 5500A Flukeby Direct sourcing
31 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
DC Voltage 1 V to 1000 V 0.015% to 0.01% Using Multifunctioncalibrator 5500A Flukeby Direct sourcing
32 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
DC Voltage 10 mV to 1 V 0.1% to 0.015% Using Multifunctioncalibrator 5500A Flukeby Direct sourcing
33 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 1 m ohm to 10 ohm 1.35% to 2.4% Using shunts & DecadeBox Maxwell, ModelDR 8 Direct sourcing
34 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 10 M ohm to 100 Mohm
0.08% to 0.6% Using Multifunctioncalibrator 5500 A Flukeby Direct sourcing
35 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 10 ohm to 100 k ohm 0.2% to 0.02% Using Multifunctioncalibrator 5500 A Flukeby Direct sourcing
36 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 100 k ohm to 10 M ohm 0.02% to 0.08% Using Multifunctioncalibrator 5500 A Flukeby Direct sourcing
37 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 100 M ohm to 300 Mohm
0.6% to 1.0% Using Multifunctioncalibrator 5500 A Flukeby Direct sourcing
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 29 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
Site Facility
38 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 300 M ohm to 100 Gohm
3.4% Using Mega Ohm BoxMaxwell, Model DB 231for calibration ofMeggers upto 5kV byDirect method
39 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
B type Thermocouples 600 ° C to 1750 ° C 0.75° C Using Radix / FlukeMultifunction calibratorby Simulation method
40 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
E type Thermocouple -200 ° C to 1000 ° C 0.44° C Using Radix / FlukeMultifunction calibratorby Simulation method
41 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
J type Thermocouple -200 °C to 750 °C 0.2°C Using Radix / FlukeMultifunction calibratorby Simulation method
42 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
K type Thermocouple -200 °C to 1350 °C 0.25°C Using Radix / FlukeMultifunction calibratorby Simulation method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 30 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
Site Facility
43 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
N type Thermocouple 50 °C to 1750 °C 0.75°C Using Radix / FlukeMultifunction calibratorby Simulation method
44 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
R type Thermocouple 50 °C to 1750 °C 0.41°C Using Radix / FlukeMultifunction calibratorby Simulation method
45 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
RTD -200 °C to 800 °C 0.35°C Using Radix / FlukeMultifunction calibratorby Simulation method
46 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
S type Thermocouple 50 °C to 1750 °C 0.70°C Using Radix / FlukeMultifunction calibratorby Simulation method
47 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
T type Thermocouple -200 °C to 400 °C 0.27°C Using Radix / FlukeMultifunction calibratorby Simulation method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 31 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
Site Facility
48 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
B type Thermocouple 600 ° C to 1750 ° C 0.75° C Using Radix / FlukeMultifunction calibratorby Simulation method
49 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
E type Thermocouples -200 ° C to 1000 ° C 0.75° C Using Radix / FlukeMultifunction calibratorby Simulation method
50 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
J type Thermocouples -200 °C to 750 °C 0.75°C Using Radix / FlukeMultifunction calibratorby Simulation method
51 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
K type Thermocouples -200 °C to 1350 °C 0.75°C Using Radix / FlukeMultifunction calibratorby Simulation method
52 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
N type Thermocouples 50 °C to 1750 °C 0.75°C Using Radix / FlukeMultifunction calibratorby Simulation method
53 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
R type Thermocouples 50 °C to 1750 °C 0.75°C Using Radix / FlukeMultifunction calibratorby Simulation method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 32 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
Site Facility
54 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
RTD -200 °C to 800 °C 0.35°C Using Radix / FlukeMultifunction calibratorby Simulation method
55 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
S type Thermocouples 50 °C to 1750 °C 0.75°C Using Radix / FlukeMultifunction calibratorby Simulation method
56 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
T type Thermocouples -200 °C to 400 °C 0.75°C Using Radix / FlukeMultifunction calibratorby Simulation method
57 ELECTRO-TECHNICAL- TIME &FREQUENCY(Measure)
Capacitance 1kHz 1 nF to 100 micro F 3% to 0.7% Using 6 ½ DMM Fluke8846A by Directmeasure
58 ELECTRO-TECHNICAL- TIME &FREQUENCY(Measure)
Capacitance 1kHz 100 micro F to 300micro F
0.7% to 1.2% Using 6 ½ DMM Fluke8846A by Directmeasure
59 ELECTRO-TECHNICAL- TIME &FREQUENCY(Measure)
Capacitance 1kHz 100 micro F to 300micro F
0.7% to 1.2% Using 6 ½ DMM Fluke8846A by Directmeasure
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 33 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
Site Facility
60 ELECTRO-TECHNICAL- TIME &FREQUENCY(Measure)
Digital / Analog StopWatch / Timer
10 sec to 59 min 1.51sec to 2sec Using Digital Timeinterval meter byComparison Method
61 ELECTRO-TECHNICAL- TIME &FREQUENCY(Measure)
Frequency 10 Hz to 1 M Hz 0.8%% to 1.40% Using 6 ½ DMM Fluke8846A by Directmeasure
62 ELECTRO-TECHNICAL- TIME &FREQUENCY (Source)
Capacitance 1kHz 0.5 n F to 100 micro F 3% to 0.7% Using Multifunctioncalibrator 5500A Flukeby Direct Method
63 ELECTRO-TECHNICAL- TIME &FREQUENCY (Source)
Capacitance 1kHz 100 micro F to 300micro F
0.7% to 1.2% Using Multifunctioncalibrator 5500A Flukeby Direct Method
64 ELECTRO-TECHNICAL- TIME &FREQUENCY (Source)
Frequency 10 Hz to 100 k Hz 0.015% to 0.065% Using Multifunctioncalibrator 5500A Flukeby Direct Method
65 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Profile Projector (LinearScale) L.C. 0.001 mm
upto to 200 mm 2.5µm Using Slip Gauge Set
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 34 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
Site Facility
66 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Profile Projector(Angular Scale) L.C. 1Min
upto to 360 deg 3 Min of arc Using Slip Gauge Set,Angle Gauge,Cylindrical Pin byComparison Method
67 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Profile Projector(Magnification)
10X to 100X 0.2% Using Slip Gauge Set,Angle Gauge,Cylindrical Pin byComparison Method
68 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Straight Edge Up to 2 mtr 18 µm Using Slip Gauge Set,Surface Plate, SpiritLevel & Feeler Gauge
69 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Surface Plate 3000 to 3000 mm 3 µm Using Spirit Level
70 MECHANICAL-PRESSUREINDICATING DEVICES
Hydraulic PressureGauge / Digital /Analog PressureGauge / PressureIndicator
0 bar to 30 bar 0.8% of rdg to 0.8% ofrdg
Using Digital PressureGauge
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 35 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
Site Facility
71 MECHANICAL-PRESSUREINDICATING DEVICES
Hydraulic PressureGauge / Digital /Analog PressureGauge / PressureIndicator
30 bar to 600 bar 0.8% of rdg to 0.8% ofrdg
Using digital pressuregauge
72 MECHANICAL-PRESSUREINDICATING DEVICES
Vacuum Gauge /Indicator
(-) 0.9 bar to 0 bar 0.8% of rdg to 0.8% ofrdg
Using Digital VacuumGauge by DirectComparison DKD-R-6-1
73 MECHANICAL- UTM,TENSION CREEPAND TORSIONTESTING MACHINE
Verification of UniaxialTesting MachinesCompression
100kN to 500kN 0.60% Using class I range ofForce ProvingInstrument
74 MECHANICAL- UTM,TENSION CREEPAND TORSIONTESTING MACHINE
Verification of UniaxialTesting MachinesTension Mode
100N to 10kN 0.65% Using StandardsNewton Weights (TrueForce Method), UsingClass I range of ForceProving Instrument
75 MECHANICAL- UTM,TENSION CREEPAND TORSIONTESTING MACHINE
Verification of UniaxialTesting MachinesTension Mode
10kN to 100kN 0.65% Using StandardsNewton Weights (TrueForce Method), UsingClass I range of ForceProving Instrument
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 36 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
Site Facility
76 MECHANICAL- UTM,TENSION CREEPAND TORSIONTESTING MACHINE
Verification of UniaxialTesting MachinesTension Mode
1N to 100N 0.65% Using StandardsNewton Weights (TrueForce Method) Class Irange of Force ProvingInstrument
77 MECHANICAL-WEIGHING SCALEAND BALANCE
Electronic WeighingBalance
5g to 80 g 0.03mg Using Standard E1Class Weights
78 MECHANICAL-WEIGHING SCALEAND BALANCE
Electronic WeighingBalance
>300g to 3kg 40mg Using Standard F2Class Weights L.C. 0.1g
79 MECHANICAL-WEIGHING SCALEAND BALANCE
Electronic WeighingBalance
>3kg to 30kg 2g Using F2 ClassWeights L.C. 1 g
80 MECHANICAL-WEIGHING SCALEAND BALANCE
Electronic WeighingBalance
80g to 200 g 0.3mg Using Standard E1Class Weights
81 MECHANICAL-WEIGHING SCALEAND BALANCE
Electronic WeighingBalance
up to 5g 0.03mg Using Standard E1Class Weights
82 THERMAL- SPECIFICHEAT & HUMIDITY
Humidity indicator ofRH Chamber
20% RH to 95% RH @25 degree C
1.9% RH Using digitalHygrometer singleposition calibration (atmeasuring location inDUC)
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 37 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
* Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure
Site Facility
83 THERMAL-TEMPERATURE
RTD / ThermocoupleWith or WithoutTemperature Indicator,Dial / DigitalThermometer
-25 degree C to 300degree C
0.22 degree C Using RTD (Pt 100), 61/2 DMM & Dry BlockCalibrator
84 THERMAL-TEMPERATURE
Temperature Indicatorwith sensor of Freezer,Oven, Chamber,Furnace
30 degree C to 250degree C
1.2 degree C Using RTD (Pt 100), , 61/2 DMM multipleposition calibration (atmeasuring location inDUC)
85 THERMAL-TEMPERATURE
Temperature Indicatorwith sensor of Oven,Chamber, Furnace
300 degree C to 1000degree C
1.9 degree C Using RTD (Pt 100), Stype Thermocouple, 61/2 DMM multipleposition calibration (atmeasuring location inDUC)
86 THERMAL-TEMPERATURE
Thermocouple With orWithout TemperatureIndicator, Dial / DigitalThermometer
300 degree C to 500degree C
1.8 degree C S type Thermocouple,6 1/2 DMM & Dry BlockCalibrator
* CMCs represent expanded uncertainties expressed at approximately the 95% level of confidence, using a coverage factor of k = 2.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2280 Page No. : 38 / 38
Validity 30/06/2019 to 29/06/2021 Last Amended on -