Laboratory Name CAL-TECH CALIBRATION SERVICES PVT. …...S.No Discipline / Group Quantity Measured/...
Transcript of Laboratory Name CAL-TECH CALIBRATION SERVICES PVT. …...S.No Discipline / Group Quantity Measured/...
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
Permanent Facility
1 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
“V” Block for
Parallelism
0 to 200 mm 8.0µm Comparison with
calibrated Square
Cylinder & Lever Dial
2 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
“V” Block for
Squareness
0 to 200 mm 6.6µm Comparison with
calibrated Square
Cylinder & Lever Dial
3 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
“V” Block for
Symmetricity
0 to 200 mm 8.0µm Comparison with
calibrated Square
Cylinder & Lever Dial
4 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Angle Plate Flatness 0 to 450 mm 12.0µm Comparison with
calibrated Square
Cylinder & Lever Dial
5 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Angle Plate for
Parallelism
0 to 450 mm 7.0µm Comparison with
calibrated Square
Cylinder & Lever Dial
6 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Angle Plate for
Squareness
0 to 450 mm 10.0µm Comparison with
calibrated Square
Cylinder & Lever Dial
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CAL-TECH CALIBRATION SERVICES PVT. LTD., FLAT NO 8 AVADHUT HEIGHTS,PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2099 Page No. : 1 / 12
Validity 14/03/2019 to 13/03/2021 Last Amended on -
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
7 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Bevel Protractor 0 to 90 ° 5min Comparison with
calibrated Angle Gauge
Block
8 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Bore Gauge – For
transmission only
0 to 1 mm 3.5µm Measurement of travel
by using Dial
calibration tester
9 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Caliper (Vernier, Dial &
Digital) (L.C. 0.01mm)
0 to 1000 mm 15.0µm Comparison by using
Caliper checker & slip
gauge block & Length
Bar
10 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Caliper (Vernier, Dial &
Digital)(L.C. 0.01mm)
0 to 600 mm 12.0µm Comparison by using
Caliper checker & slip
gauge block & Length
Bar.
11 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Coating Thickness
MeterL.C. 0.001 mm
0 to 1 mm 8.0µm Comparison with
calibrated Shims (Foils)
12 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Comparator Stand For
Flatness of Base
0 to 300 mm 3.0µm By using Electronics
Probe With Indicator
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CAL-TECH CALIBRATION SERVICES PVT. LTD., FLAT NO 8 AVADHUT HEIGHTS,PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2099 Page No. : 2 / 12
Validity 14/03/2019 to 13/03/2021 Last Amended on -
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
13 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Comparator StandFor
Flatness of Base
0 to 100 mm 1.6µm By using Electronics
Probe With Indicator
14 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Cylindrical Setting
Master
0 to 100 mm 1.5µm Comparison with
calibrated Gauge
Blocks
15 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Degree Protractor /
Combination Set(L.C. 1
deg)
0 to 180 ° 43.0min. Comparison with
calibrated Angle Gauge
Block
16 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Depth Gauge
(Vernier/Dial/
Digital)(L.C. 0.01mm)
0 to 600 mm 13.0µm Comparison by Using
Depth Micrometer
Checker.
17 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Depth Micrometer(L.C.
0.01 mm)
0 to 300 mm 12.0µm Comparison by using
Depth Micrometer
Checker
18 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Dial Calibration
Tester(L.C. 0.0001mm)
0 to 25 mm 1.3µm Comparison with
calibrated Gauge
Blocks
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CAL-TECH CALIBRATION SERVICES PVT. LTD., FLAT NO 8 AVADHUT HEIGHTS,PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2099 Page No. : 3 / 12
Validity 14/03/2019 to 13/03/2021 Last Amended on -
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
19 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Dial Gauge - (Lever
Type)L.C. 0.001 mm
0 to 2 mm 2.0µm Measurement of travel
by using Dial
calibration tester
20 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Dial Gauge - (Plunger
Type)L.C. 0.001 mm
0 to 25 mm 2.0µm Measurement of travel
by using Dial
calibration tester
21 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Dial Gauge - (Plunger
Type)L.C. 0.01 mm
0 to 50 mm 7.5µm Measurement of travel
by using Dial
calibration tester
22 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Dial Snap Gauge 01 to 200 mm 5.0µm By using Slip Gauge
Block set
23 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Dial Thickness Gauge
(L.C. 0.001 mm)
0 to 25 mm 1.0µm Comparison with
calibrated Gauge
Blocks
24 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Electronics Probe With
Indicator(L.C.
0.0001mm)
0 to 25 mm 0.7µm Comparison with
calibrated Gauge
Blocks
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CAL-TECH CALIBRATION SERVICES PVT. LTD., FLAT NO 8 AVADHUT HEIGHTS,PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2099 Page No. : 4 / 12
Validity 14/03/2019 to 13/03/2021 Last Amended on -
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
25 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
External
Micrometer(L.C. 0.001
mm)
>100 to 300 mm 9.0µm Comparison by using
Micrometer Checking
set & Long Slip Gauge
Block
26 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
External
Micrometer(L.C. 0.001
mm)
0 to 100 mm 2.0µm Comparison by using
Micrometer Checking
set & Long Slip Gauge
Block.
27 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
External
Micrometer(L.C. 0.01
mm)
0 to 100 mm 3.7µm Comparison by using
Micrometer Checking
set & Long Slip Gauge
Block
28 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
External
Micrometer(L.C. 0.01
mm)
>100 to 1000 mm 7.0µm Comparison by using
Micrometer Checking
set & Long Slip Gauge
Block.
29 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Feeler gauge / Shims
(Foils) of Coating
Thickness Gauge
0 to 1 mm 1.3µm By using electronics
probe with Indicator
30 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Height GaugeVernier,
Dial & Electronic(L.C.
0.01 mm)
0 to 1000 mm 15.0µm Comparison by using
Caliper checker & Slip
Gauge Block & Length
Bar
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CAL-TECH CALIBRATION SERVICES PVT. LTD., FLAT NO 8 AVADHUT HEIGHTS,PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2099 Page No. : 5 / 12
Validity 14/03/2019 to 13/03/2021 Last Amended on -
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
31 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Height GaugeVernier,
Dial & Electronic(L.C.
0.01 mm)
0 to 600 mm 12.0µm Comparison by using
Caliper checker & Slip
Gauge Block & Length
Bar
32 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Inside Dial Caliper 0 to 100 mm 6.0µm By using Slip Gauge
Block
33 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Internal Micrometer- 2
Point(for Micrometer
head) (L.C. 0.01 mm)
0 to 100 mm 10.0µm By using ULM300
Comparison with
calibrated Gauge
Blocks
34 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Internal Micrometer- 2
Point(for Micrometer
Range)(L.C. 0.01 mm)
0 to 1000 mm 12.0µm By using ULM300
Comparison with
calibrated Gauge
Blocks
35 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Measuring Pins 0.5 to 20 mm 1.4µm Comparison with
calibrated Gauge
Blocks
36 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Measuring Scale 0 to 2000 mm 118 * Square root of L /
1000µm
Using Scale Calibration
Unit
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CAL-TECH CALIBRATION SERVICES PVT. LTD., FLAT NO 8 AVADHUT HEIGHTS,PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2099 Page No. : 6 / 12
Validity 14/03/2019 to 13/03/2021 Last Amended on -
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
37 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Measuring Tape / Pie
Tape
0 to 50 meter 118 * Square root of L /
1000µm
Using Scale Calibration
Unit
38 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Micrometer Setting
Standard
25 to 975 mm 5.4µm Comparison with
calibrated Gauge
Blocks
39 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Parallel Thread Plug
Gauge
100 to 300 mm 3.0µm By Using ULM300
40 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Parallel Thread Plug
Gauge
2 to 100 mm 2.6µm By Using ULM300
41 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Pistol Caliper (L.C.
0.10 mm)
0 to 50 mm 64.0µm Comparison with
calibrated Gauge
Blocks
42 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Plain Plug
Gauge/Width Gauge
0.5 to 200 mm 1.9µm Comparison with
calibrated Gauge
Blocks
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CAL-TECH CALIBRATION SERVICES PVT. LTD., FLAT NO 8 AVADHUT HEIGHTS,PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2099 Page No. : 7 / 12
Validity 14/03/2019 to 13/03/2021 Last Amended on -
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
43 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Plain Plug
Gauge/Width Gauge
201 to 400 mm 3.5µm Comparison with
calibrated Gauge
Blocks
44 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Plain Ring Gauge 2 to 300 mm 1.6µm Measurement by using
ULM300
45 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Plain Snap Gauge 201 to 400 mm 3.2µm Measurement of gap
size by inserting
calibrated Gauge
Blocks
46 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Plain Snap Gauge 3 mm to 200 mm 2.5µm Measurement of gap
size by inserting
calibrated Gauge
Blocks.
47 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Radius Gauge 0 to 25 mm 11.0µm Using Profile Projector
48 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Right Angle / Engineers
Square (Squareness)
0 to 450 mm 10.0µm Comparison with
calibrated Square
Cylinder & Lever Dial
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CAL-TECH CALIBRATION SERVICES PVT. LTD., FLAT NO 8 AVADHUT HEIGHTS,PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2099 Page No. : 8 / 12
Validity 14/03/2019 to 13/03/2021 Last Amended on -
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
49 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Taper Scale 1 to 15 mm 58.0µm By using Profile
Projector
50 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Taper Thread Plug
Gauge
2 to 100 mm 4.0µm Using FCDM by
Comparison Method
51 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Thread measuring wire 0.170 to 6.35 mm 1.5µm Comparison with
calibrated Gauge
Blocks
52 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Thread Pitch Gauge 0.25 to 8.0 mm pitch 15.0µm Using Profile Projector
53 MECHANICAL-
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)
Thread Ring Gauge 2 to 100 mm 1.6µm By using ULM300
54 MECHANICAL-
DIMENSION
(PRECISION
INSTRUMENTS)
Floating Carriage
Diameter Measuring
Machine L.C. 0.0001
mm
0 to 100 mm 3.0µm Comparison with
calibrated Cylindrical
Setting Master & Slip
Gauge Blocks
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CAL-TECH CALIBRATION SERVICES PVT. LTD., FLAT NO 8 AVADHUT HEIGHTS,PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2099 Page No. : 9 / 12
Validity 14/03/2019 to 13/03/2021 Last Amended on -
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
55 MECHANICAL-
PRESSURE
INDICATING DEVICES
Hydraulic
Pressure:Pressure
Indicating
Devices(Type: Dial,
Digital, Analogue
gauges)
0 to 70 bar 0.3 bar Using Digital Pressure
Gauge with Hydraulic
Test Pump by
Comparison Method as
per DKD R6–1
56 MECHANICAL-
PRESSURE
INDICATING DEVICES
Hydraulic
Pressure:Pressure
Indicating
Devices(Type: Dial,
Digital, Analogue
gauges)
0 to 700 bar 2.5 bar Using Digital Pressure
Gauge with Hydraulic
Test Pump by
Comparison Method as
per DKD R6–1
57 MECHANICAL-
PRESSURE
INDICATING DEVICES
Pneumatic
Pressure:Pressure
Indicating
Devices(Type: Dial,
Digital, Analogue
gauges)
0 to 7 bar 0.08bar Using Digital Pressure
Gauge with pneumatic
Test Pump by
Comparison Method as
per DKD R6–1
58 MECHANICAL-
PRESSURE
INDICATING DEVICES
Pressure Indicating
Devices:Vacuum
Gauges(Type: Dial,
Digital, Analogue
gauges)
-0.85 bar to 0 0.05 bar Using Digital Pressure
Gauge with Pneumatic
Pump by Comparison
Method as per DKD
R6–1
59 MECHANICAL-
TORQUE
GENERATING
DEVICES
Torque Wrench (Type
I/Class B,C and Type
II/Class A,B) Clockwise
direction only.
2 to 1000 Nm 3.21 %rdg Using Torque Sensor
with indicator with
Torque Wrench Tester
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CAL-TECH CALIBRATION SERVICES PVT. LTD., FLAT NO 8 AVADHUT HEIGHTS,PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2099 Page No. : 10 / 12
Validity 14/03/2019 to 13/03/2021 Last Amended on -
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
Site Facility
1 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Electronic HeightGauge(L.C. 0.0001mm)
0 to 1000 mm 9.5µm Comparison withcalibrated Long SlipGauge Blocks
2 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Electronic HeightGauge(L.C. 0.0001mm)
0 to 600 mm 6.0µm Comparison withcalibrated Long SlipGauge Blocks
3 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Surface Plate-CastIron- Granite (Gr-1)
3000 x 3000 mm 4.6 * Square root ofL+W / 150µm
Using Spirit Level bycomparison method :Sens-0.01 mm/meter
4 MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Profile Projector /OpticalMicroscopeAngular(L.C. 1 min)
0 to 360 degree 3.0min. Comparison withcalibrated Glass Scale& Angle Gauge Block
5 MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Profile Projector /OpticalMicroscopeLinear X,YAxis L.C. 0.001mm
0 to 200 mm 6.9µm Comparison withcalibrated Glass Scale& Angle Gauge Block
6 MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Profile Projector /OpticalMicroscopeMagnification
10X to 100X 0.1% Comparison withcalibrated Glass Scale& Angle Gauge Block
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CAL-TECH CALIBRATION SERVICES PVT. LTD., FLAT NO 8 AVADHUT HEIGHTS,PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2099 Page No. : 11 / 12
Validity 14/03/2019 to 13/03/2021 Last Amended on -
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
7 MECHANICAL-PRESSUREINDICATING DEVICES
HydraulicPressure:PressureIndicatingDevices(Type: Dial,Digital, Analoguegauges)
0 to 70 bar 0.3 bar Using Digital PressureGauge with HydraulicTest Pump byComparison Method asper DKD R6–1
8 MECHANICAL-PRESSUREINDICATING DEVICES
HydraulicPressure:PressureIndicatingDevices(Type: Dial,Digital, Analoguegauges)
0 to 700 bar 2.5 bar Using Digital PressureGauge with HydraulicTest Pump byComparison Method asper DKD R6–1
9 MECHANICAL-PRESSUREINDICATING DEVICES
PneumaticPressure:PressureIndicatingDevices(Type: Dial,Digital, Analoguegauges)
0 to 7 bar 0.08bar Using Digital PressureGauge with pneumaticTest Pump byComparison Method asper DKD R6–1
10 MECHANICAL-PRESSUREINDICATING DEVICES
Pressure IndicatingDevices:VacuumGauges(Type: Dial,Digital, Analoguegauges)
-0.85 bar to 0 0.05 bar Using Digital PressureGauge with PneumaticPump by ComparisonMethod as per DKDR6–1
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name CAL-TECH CALIBRATION SERVICES PVT. LTD., FLAT NO 8 AVADHUT HEIGHTS,PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2099 Page No. : 12 / 12
Validity 14/03/2019 to 13/03/2021 Last Amended on -