Lab Manual for Electronic Circuits Final March 13 2011
-
Upload
narayananmeera07 -
Category
Documents
-
view
217 -
download
0
Transcript of Lab Manual for Electronic Circuits Final March 13 2011
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
1/43
ELECTRONIC CIRCUITS(802312-4)
Laboratory Manual
(Spring 2011: Term-2, 1431/1432H)
Prepared by:
Dr Iqbal KhanDr Tarek AbdolkaderDr Waheed Younis
Revised & Approved By: Electronics Sequence Committee, Date: March 1, 2011
-
KINGDOM OF SAUDI ARABIA Ministry of Higher Education
Umm AlQura University College of Engineering and Islamic Architecture
Electrical Engineering Department
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
2/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 1
Table of Contents
INTRODUCTION ...................................................................................... 2
LABORATORY SAFETY ..................................................................... 2HOW TO WRITE A LAB REPORT .................................................... 4HOW TO WRITE PRELAB REPORT ................................................ 5
EXPERIMENT #1 ...................................................................................... 6 FREQUENCY RESPONSE OF RC-COUPLED AMPLIFIER ............ 6
EXPERIMENT #2 .................................................................................... 13INVERTING AND NON-INVERTING VOLTAGE AMPLIFIERS . 13
EXPERIMENT #3 .................................................................................... 22INTEGRATOR, DIFFERENTIATOR & VOLTAGE FOLLOWER 22
EXPERIMENT #4 .................................................................................... 32WIEN BRIDGE OSCILLATOR USING OP-AMP ............................. 32
EXPERIMENT #5 .................................................................................... 37RC-PHASE-SHIFT OSCILLATOR USING BJT ................................ 37
MINI-PROJECT 1 ................................................................................... 41MINI-PROJECT 2 ................................................................................... 42
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
3/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 2
INTRODUCTION
This manual has been prepared for use in the course 802312-4, Electronic Circuits. The
laboratory exercises are devised is such a way as to reinforce the concepts taught in the
lectures. Before performing the experiments, the student must be aware of the basiclaboratory safety rules for minimizing any potential dangers. The students must complete
and submit the pre-lab report of each exercise before performing the experiment. The
objective of the experiment must be kept in mind throughout the lab experiment.
LABORATORY SAFETY- Safety in the electrical engineering laboratory, as everywhere else, is a matter of
the knowledge of potential hazards, following safety regulations and precautions,
and common sense.
- Observing safety precautions is important due to pronounced hazards in any
electrical engineering laboratory.
- All the UQU Electrical Engineering Students, Teaching Assistants, Lab Engineers,
and Lab technicians are required to be familiar with the LABORATORY SAFETY
GUIDELINES FOR THE UQU ELECTRICAL ENGINEERING
UNDERGRADUATE LAB AREAS published on the department web-page.
- Practice electrical safety at all times while constructing, analyzing and
troubleshooting circuitry.- Do not accompany any drinks or water with you inside the Lab.
- If you observed an electrical hazard in the lab area NOTIFY THE
INSTRUCTOR/LAB ASSISTANT IMMEDIATELY!
- Acquaint yourself with the location of the following safety items within the lab:a. fire extinguisher
b. first aid kitc. Fire-exitd. telephone and emergency numbersDepartment/Person Telephone
Fire-Department Emergency 0 - 998Dean College of Engineering & Islamic
Architecture / Secretary 0 - 5281155 / 1177
EE Department Chair / Secretary 1024 / 1203Dean of Students Affairs: 0 - 5561916
UQU University Service /Security 0 - 5563478 & 0 - 5562524 / x 6828 / x6027UQU Medical Clinic/ Emergency/
Reception 0 - 5589953/ x5658 / x5699
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
4/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 3
LABORATORY SAFETY REVIEW QUESTIONS:
1. YES OR NO: Have you read the Laboratory Safety Guidelines for the UQU Electrical Engineering Undergraduate Lab Areas ?
2. What should you do if an emergency situation occurs in the laboratory?
3. In the event of a fire, police, or medical emergency do you know theemergency telephone number ? Write it down.
4. TRUE OR FALSE : There is an increased risk of electric shock if you enterthe lab area bare feet .
5. TRUE OR FALSE : There is no increased risk of electric shock and theequipment is not affected in any way if food and drinks are allowed in the labarea.
6. TRUE OR FALSE : The students may be allowed to work alone in any lab areawithout the supervision of Teaching Assistant (TA) or Course Professor.
7. Fill in the blanks: a. Voltages above ________ Vrms AC are dangerous.
b. Voltages above ________ DC are dangerous.
8. TRUE OR FALSE: In the event of fire emergency use elevator to evacuatefaster.
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
5/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 4
HOW TO WRITE A LAB REPORT
A lab report for each experiment is to be submitted by each member (student) of ateam one week after the lab session is completed. The lab report must be type writtenin the MSWord (Times-Roman 12 font) format and it must contain the following:
1. Cover page containing:
Electronic Circuits 802312-4 Experiment #______
Experiment Title: _________________________________
Group #: ___________
Your Name: ________________ & I.D. #: _________________
2. Objectives : Not copied from the lab manual
3. Specifications of Equipment Used :
4. Procedure : Steps you did in the lab. It is not copied from the lab manual
5. Block Diagram or Circuit Diagram should be included
6. Result or Analysis : Compare the Pre-lab results with those obtained in theexperiment. Summary of what you discovered. (attach the pre-lab with the labreport)
7. Answers to Questions: Answer to observation questions in the lab experiment,lab review questions and lab safety review questions at the end of theexperiment in a written form (MSWord document)
8. Conclusion: The conclusions based on the experiment and other observationsmust be clearly discussed in the laboratory report.
9. Remarks or Comments: You may write your comments regarding yourexperience of each lab experiment.
(The laboratory report will be graded for content and written English)
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
6/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 5
HOW TO WRITE PRELAB REPORT
Pre-lab report must be completed and submitted before the start of each experiment.The pre-lab report is graded and is part of your lab grades.
The Pre-lab should be in the following format:
1. Cover page containing:
- Electronic Circuits 802213-4 Experiment #______- Experiment Title: _________________________________- Group #: ___________
- Your Name: ________________ & I.D. #: _________________
2. Solution of Pre-Lab Questions in MSWord, New Times Roman, Font: 12 ,if the solution is descriptive, otherwise hand written solution is also
appropriate.
You may need a copy of this pre-lab to compare your solution with the lab experimentmeasurements.
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
7/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 6
EXPERIMENT #1
FREQUENCY RESPONSE OF RC-COUPLED AMPLIFIER
OBJECTIVE:
At the completion of this experiment, students will be able to: I. demonstrate the frequency response of single-stage amplifier.
II. describe the effect of the emitter by-pass capacitor.
BACKGROUND:
An amplifier is a device in which one of the output signal parameters (eithervoltage or current) is controlled by any one of the input signal parameters. The relationshould be proportional, with the constant of proportionality represents the gain of theamplifier.
RC coupled amplifier is a common-emitter transistor amplifier configuration(see Figure 1). The amplifier given in Figure 1 is biased using potential divider biasingcircuit. Capacitor elements are used for the coupling of different stages of theamplifier. The resistor RE is used for bias stabilization
Figure 1 RC-coupled amplifier with voltage divider biasing
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
8/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 7
The dc operating point ( V CE , I C) depends on the values of RE and RC resistors.The values of V CE and I C are not independent. They are related through a linearrelationship, which is called the dc load line. The dc operating point (Q-point) can beone of the points of the load line. Q-point must be set so that the signal variations at theinput terminal are amplified and accurately reproduced at the output terminal.
The capacitors in the circuit determine the frequency response of the amplifier.For dc bias, the reactance of these capacitors is infinitely high, so they act as an opencircuit. This prevents the change of dc bias point due to adjacent stages. Sometimes, a
by-pass capacitor is put in parallel with the emitter resistance RE. The ac voltage gain isgiven by:
where r e si the ac emitter resistance and Z E is the impedance from the emitter toground. Referring to Fig. 2, Z E is R E1 + R E2 in parallel with X CE .
PRE-LAB:
The following pre-lab must be completed and submitted before the start of thisexperiment. The pre-lab is graded and is part of your lab grades.Solve the following exercises on separate sheets of paper and submit your solution
before the start of the lab experiment. You may need a copy of this pre-lab to compareyour solution with the lab experiment measurements.
Analyze the circuit shown in Figure 2 to determine:1- The dc bias point V CE , I C. 2- The voltage gain at frequencies f =100 Hz, 1 kHz, and 100 kHz
3-
Assume that the capacitor C E is removed and recalculate the voltage gainat the same frequencies given in 2.
Figure 2 : Single-Stage Amplifier with by-pass capacitor.
C v
e E
R A
r Z =
+
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
9/43
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
10/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 9
11- Calculate the gain = V O /V i , in each step.
Table-II: Input and Output Voltages without C E connected
f (Hz) V i (Vrms ) V O (Vrms ) Gain . f (Hz) V i (Vrms ) V O (Vrms ) Gain .
12- Plot the frequency response of your result in table-II on a log-scale.
___________________________________ _______________Instructors Signature Date
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
11/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 10
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
12/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 11
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
13/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 12
LAB REVIEW QUESTIONS:
1. Measure the operating point of the amplifier in figure 1 and compare themeasured values with those obtained theoretically.
2. What is the effect of the by-pass capacitor of the amplifier in figure 2?3. From the results in table-I, find the cut-off frequency.4. From the results in table-II, find the cut-off frequency.
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
14/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 13
EXPERIMENT #2
INVERTING AND NON-INVERTING VOLTAGE AMPLIFIERS
OBJECTIVE:
At the completion of this experiment, students will be able to: I. Design an inverting voltage amplifier using 741 type operational amplifier for
a gain of -10 and to measure its frequency response.II. Design a non-inverting voltage amplifier using 741 type operational amplifier
for a gain of 11 and to measure its frequency response.
BACKGROUND:
An inverting amplifier is shown in Figure 1. Its function is to invert inputvoltage and level its value with a controlled amount according to the values of theresistors Ri and Rf . Assuming ideal Op-Amp, the overall (closed-loop) voltage gain isgiven by:
out f v
in i
V R A
V R= =
A non-inverting amplifier is shown in Figure 2. The input is now connected tothe non-inverting terminal of the Op-Amp. The function of non-inverting amplifier isto control the level of a certain input voltage preserving its polarity. The overallvoltage gain for an ideal Op-Amp is given by:
1out f vin i
V R A
V R= = +
Figure 1 Inverting Amplifier Figure 2 Non-inverting Amplifier
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
15/43
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
16/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 15
EQUIPMENT REQUIRED: 2x DC Power Supply Function Generator 741 IC Op-Amp Resistors (1k , 10k , 100k ) Digital multi-meter
EXPERIMENT PROCEDURE:
PART I: Inverting Amplifier:
a. Inverting DC gain
Figure 5 : Inverting Amplifier .
1- Construct the circuit as shown in figure 5.2- Use R = 1 k .3 Connect the OpAmp DC supply voltage 12= CC V V.
4 Use V S as a DC supply voltage of 500 mV. 5 Vary RF from 0 to 20 k at constant rate.
6
Measure V O
for
each
value
of
RF
, then
record
it
in
table
I.
7 Calculate the closed loop gain V O/ V S in each step in table I. 8 Plot Gain versus RF using proper scale using data in table I. 9 Determine the value of RF at which the gain is 10.
Table I: Gain at different values of RF for Inverting Amplifierof Fig. 5.
RF (k ) V O (V) Gain .0 5
10 15 20 25 30
___________________________________ _______________Instructors Signature Date
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
17/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 16
b. Frequency Response:
1- Keep the circuit connected in part (a) with RF = 10 k .2- Use V S AC supply voltage (Function Generator).3- Using DMM measure the ac voltage of V S . Vary the amplitude until the
reading of DMM gives 500 mV(rms).4- Vary the frequency ( f ) from 20 to 20kHz at constant rate.5- Measure V O for each f , then record it in table-II.6- Calculate the Gain , then record it in table-II.7- Plot the frequency response of the amplifier V o /V i against f (Hz) on a log-
scale, using your results in table-II.
Table-II: Input and Output Voltages.
f (Hz) V O (Vrms ) Gain . f (Hz) V O (Vrms ) Gain .
___________________________________ _______________Instructors Signature Date
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
18/43
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
19/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 18
PART II: Non inverting Amplifier:
a. Non inverting DC gain
Figure 6 : Non-inverting Amplifier .
1- Construct the circuit as shown in figure 6.2- Use RF = 100 k .3 Connect the OpAmp DC supply voltage 12= CC V V.
4 Use V S as a DC supply voltage of 500 mV. 5 Vary R from 0 to 20 k at constant rate. 6 Measure V O for each value of R , then record it in table I.
7 Calculate the closed loop gain V O/ V S in each step in table I. 8 Plot Gain versus R using proper scale using data in table I. 9 Determine the value of R at which the gain is 11.
Table I: Gain at different values of resistance R for Non inverting Amplifier of Fig. 6.
R (k ) V O (V) Gain .0 5
10 15 20 25 30
___________________________________ _______________Instructors Signature Date
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
20/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 19
b. Frequency Response:
1- Keep the circuit connected in part (a) with R = 10 k .2- Use V S AC supply voltage (Function Generator).3- Using DMM measure the ac voltage of V S . Vary the amplitude until the
reading of DMM gives 500 V(rms).4- Vary the frequency ( f ) from 20 to 20kHz at constant rate.5- Measure V O for each f , then record it in table-II.6- Calculate the Gain , then record it in table-II.7- Plot the frequency response of the amplifier V o /V i against f (Hz) on a log-
scale, using your results in table-II.
Table-II: Input and Output Voltages.
f (Hz) V O (Vrms ) Gain . f (Hz) V O (Vrms ) Gain .
___________________________________ _______________Instructors Signature Date
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
21/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 20
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
22/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 21
LAB REVIEW QUESTIONS:
1 Compare your results for inverting amplifier with V O /V S = R f /R . Find the percentage error.
2 Compare your results for non inverting amplifier with 1O f S
V RV R
= + .
Find the percentage error.
3 What is the maximum output voltage that can be obtained?
4 Determine the cut off frequency of the obtained frequency responses.
5 If the value of the resistor R is increased, what will happen?
6 If the value of the resistor RF is increased, what will happen?
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
23/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 22
EXPERIMENT #3
INTEGRATOR, DIFFERENTIATOR & VOLTAGE FOLLOWER
OBJECTIVE:
At the completion of this experiment, students will be able to
I. design an inverting voltage integrator using 741 type operational amplifierfor a time constant of 200s and observe the output wave shape for a squarewave input of appropriate frequency.
II. design an inverting voltage differentiator using 741 type operationalamplifier for time constant of 200 s and observe the output wave shape fora triangular wave input of appropriate frequency.
III. study the voltage follower constructed from 741 op-amp.
THEORY/BACKGROUND:
I. Integrator: An op-amp integratorsimulates the integration function, which isa summing process that determines the totalarea under the curve of a function. The op-amp integrator circuit is depicted here. It
can be shown (section 13.3 of the text book) that the output voltage (for a constantinput voltage) is given by: .
In other words, the output voltage will be a ramp function for a constant inputvoltage which is the characteristic of an integrator. Slope of the ramp isdetermined by magnitude of input voltage and RC (also called the time constant).Maximum value of the ramp is determined by the supply voltage of the op-amp.
II. Differentiator: An op-amp differentiatorsimulates the mathematical function ofdifferentiation. The op-amp differentiatorcircuit is shown here. Again it can be
proven that the output voltage (for asteadily increasing input voltage) is given
by:.
In other words, output voltage dependsupon the rate of change of input voltage
R
CVinVout
VinVout
R
C
Figure 1. Op-amp integrator circuit
Figure 2. Op-amp differentiator circuit
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
24/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 23
( ) which is the characteristic of the differentiator. Magnitude of the outputvoltage is determined by the slope of the input voltage and RC (also called thetime constant). Maximum value of the output voltage is determined by the supplyvoltage of the op-amp.
III. Voltage Follower: We know that for the non-inverting amplifier (figure 3), theoutput voltage is:
.
If in this circuit, is replaced by a short
circuit and is replaced by open circuit, theoutput voltage become
and the new circuit will be called voltage
follower (figure 4).In voltage follower, the output voltage is same as the input voltage for a certainrange of frequencies.
R2
R1
VoutVin
VoutVin
Figure 3. Non-inverting amplifier
Figure 4. Voltage follower
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
25/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 24
PRE-LAB:
The following pre-lab must be completed and submitted before the start of thisexperiment. The pre-lab is graded and is part of your lab grades.Solve the following exercises on separate sheets of paper and submit your solution
before the start of the lab experiment. You may need a copy of this pre-lab to compareyour solution with the lab experiment measurements.
I. You want to design a 741 op-amp based integrator (figure 1), with a time constantof 200s.1. First you want to choose appropriate values of R and C. If you choose R=1k ,
what should be the value of C? If C is chosen as 0.01 F, what should be thevalue of R?
2. If input voltage is 3 volt constant, supply voltage for op-amp is 15 volt, drawthe input and output waveforms for 5 mSec. [All the plots should be made on
proper graph paper with correct units and scales on both axis.]3. If input voltage is 1 volt constant, supply voltage for op-amp is 15 volt, draw
the input and output waveforms for 5 mSec.4. If input voltage is 1 volt constant, supply voltage for op-amp is 10 volt, draw
the input and output waveforms for 5 mSec.5. If the input voltage is a square wave of 5 volt peak-to-peak and 10kHz, supply
voltage for op-amp is 15 volt, draw the input and output waveforms.6. If the input voltage is a square wave of 5 volt peak-to-peak and 1kHz, supply
voltage for op-amp is 15 volt, draw the input and output waveforms.7. If the input voltage is a square wave of 5 volt peak-to-peak and 100Hz, supply
voltage for op-amp is 15 volt, draw the input and output waveforms.II. You want to design a 741 op-amp based differentiator (figure 2), with a time
constant of 200s.
1. Choose R and C of appropriate value.2. If input voltage is a ramp function of 10kV/sec, supply voltage for op-amp is15 volt, draw the input and output waveforms for 5s.
3. If input voltage is a ramp function of 50kV/sec, supply voltage for op-amp is15 volt, draw the input and output waveforms for 5s.
4. If input voltage is a ramp function of 100kV/sec, supply voltage for op-amp is15 volt, draw the input and output waveforms for 5s.
5. If the input voltage is a triangular waves of 5 volt peak-to-peak and 100Hz,supply voltage for op-amp is 15 volt, draw the input and out waveforms.
6. If the input voltage is a triangular waves of 5 volt peak-to-peak and 1kHz,supply voltage for op-amp is 15 volt, draw the input and out waveforms.
7. If the input voltage is a triangular waves of 5 volt peak-to-peak and 10kHz,supply voltage for op-amp is 15 volt, draw the input and out waveforms.
III. In a voltage follower, if the output voltage is same as the input voltage, what is the benefit of it? Where the voltage follower is used?
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
26/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 25
EQUIPMENT REQUIRED:
DC Power Supply Function Generator 741 IC Op-Amp
Resistors (2x 1k ) Capacitors (2x 0.1 F) Digital Multimeter Oscilloscope.
EXPERIMENT PROCEDURE:
PART I: Integrator:
1- Construct the circuit as shown in figure 1.2- Use R and C as computed in pre-lab.3- Connect the Op-Amp DC supply voltage as 15 V.4- Use V in as a Square-wave signal voltage of 5Vp-p.5- Set the frequency to 10 kHz.6- Use the Oscilloscope to display V in waveform on Channel-1 and V out
waveform on Channel-2.7- Plot these waveforms. (neatly)8- Change the input frequency to 1 kHz.9- Use the Oscilloscope to display V in waveform on Channel-1 and V out
waveform on Channel-2.10- Plot these waveforms. (neatly)11- Change the frequency to 100 Hz.12- Use the Oscilloscope to display V in waveform on Channel-1 and V out
waveform on Channel-2.13- Plot these waveforms. (neatly)14- Compare these waveforms with your waveforms from pre-lab.
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
27/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 26
___________________________________ _______________Instructors Signature Date
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
28/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 27
PART II: Differentiator:
1- Construct the circuit as shown in figure 2.2- Use R and C as computed in pre-lab.3- Connect the Op-Amp DC supply voltage 15 V.4- Use V in as a Triangular-wave signal voltage of 5Vp-p.5- Set the frequency to 100Hz.6- Use the Oscilloscope to display V in waveform on Channel-1 and V out
waveform on Channel-2.7- Plot these waveforms. (neatly)8- Change the frequency to 1 kHz.9- Use the Oscilloscope to display V in waveform on Channel-1 and V out
waveform on Channel-2.10- Plot these waveforms. (neatly)11- Change the frequency to 10 kHz.12- Use the Oscilloscope to display V in waveform on Channel-1 and V out
waveform on Channel-2.13- Plot these waveforms. (neatly)14- Compare these waveforms with your waveforms from pre-lab.
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
29/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 28
___________________________________ _______________Instructors Signature Date
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
30/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 29
PART III: Voltage Follower (Buffer):
1- Construct the circuit as shown in figure 3.2- Connect the Op-Amp DC supply voltage 15 V.3- Use an AC source for V in .4- Set the frequency to 10 kHz.5- Vary V in at constant rate, and Measure V out for each V in 6- Record it in table-I.7- Calculate the Gain .
Table-I: Input and Output voltages
V in (Vrms )
V Out (Vrms )
Gain V in
(Vrms ) V Out (Vrms )
Gain .
0.0 3.0 0.5 3.5 1.0 4.0 1.5 4.5 2.0 5.0 2.5 5.5
8- Set V in =1Vrms.
9- Vary frequency from 20 to 20kHz at constant rate.
10- Measure V Out for each f .
11- Record it in table-II.
Table-II: Frequency Response.
f (Hz)
V in (Vrms )
V Out (Vrms )
Gain f
(Hz) V in
(Vrms ) V Out
(Vrms ) Gain .
20 1500
50 2000 100 4000 150 8000 200 10000 500 15000
1000 20000
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
31/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 30
12- Calculate the gain.
13- Plot the frequency response ( V Out /V in versus f ).
14- Now set V in =5Vrms.
15- Vary frequency from 20 to 20kHz at constant rate.16- Measure V Out for each f .
17- Record it in table-III.
Table-III: Frequency Response.
(Hz) V in
(Vrms ) V Out
(Vrms ) Gain .
f (Hz)
V in (Vrms )
V Out (Vrms )
Gain .
20 1500 50 2000
100 4000 150 8000 200 10000 500 15000
1000 20000
18- Calculate the gain.
19- Plot the frequency response ( V Out /V in versus f ).
___________________________________ _______________Instructors Signature Date
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
32/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 31
LAB REVIEW QUESTIONS:
PART I: In your report answer the following:
1- Show thatCRsS V
S V
in
out
1
)()(
= for figure 1.
2- If the input is a sinusoidal signal, what do you expect the output to be?How will it differ from the input waveform.
3- Explain the relationship between the input and output waveforms. Howthe outputs are 'integrals' of the inputs?
PART II: In your report answer the following:
1- Show that C RsS V
S V
in
out )()(
= for figure 2.
2- If the input is a sinusoidal signal, what do you expect the output to be? Howwill it differ from the input waveform.
3- Explain the relationship between the input and output waveforms. How theoutputs are 'derivatives' of the inputs?
PART III: In your report answer the following:
1- Prove that 1+=in
Out
V
V .
2- From your experimental results, calculate the cut-off frequency.
3- If the amplitude of V in is increased , will the buffer circuit give the samefrequency response? (support your answer)
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
33/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 32
EXPERIMENT #4
WIEN BRIDGE OSCILLATOR USING OP-AMP
OBJECTIVE:
At the completion of this experiment, students will be able to design andexperimentally verify the Wien bridge oscillator using 741 type op-amp for anoscillating frequency of 5kHz.
THEORY/BACKGROUND:
A feedback circuit can produce sustained oscillations, if
i. Phase shift around feedback loop is zero degree andii. The voltage gain around the feedback loop is one.
R1 C2
C1
R2Vin Vout
Figure 5. The lead-lag circuit
Consider the lead lag circuit (figure 1). In this circuit, the output voltage peaks to one-
third of the input voltage (figure 2) i.e. and the phase shift through the
circuit is going to be zero degree at a particular resonance frequency given by
(where and ).
If this circuit is used in the positive feedback loop of an op-amp and a voltage divider(with a gain of 3) is used in the negative feedback loop as shown below (figure 3), theoverall circuit will fulfill the requirements of self sustained oscillation and will start to
Figure 6. Frequency response of lead-lag circuit
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
34/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 33
oscillate. Finally, in order to have the required gain for the negative feedback loop, weneed to have .
R
RC
C
R1
R2
Lead-lag circuit
Voltage divider
Vout
Figure 7. Wien bridge oscillator
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
35/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 34
PRE-LAB:
The following pre-lab must be completed and submitted before the start of thisexperiment. The pre-lab is graded and is part of your lab grades.Solve the following exercises on separate sheets of paper and submit your solution
before the start of the lab experiment. You may need a copy of this pre-lab to compareyour solution with the lab experiment measurements.
1. For the lead-lag circuit of figure 1, prove that the transfer function will be
2. Using above transfer function, show that the magnitude of the transfer
function will be 1/3 when or .3. Using the same transfer function, show that the phase angle of the transfer
function will be zero at or .4. For the non-inverting amplifier portion of the op-amp of figure 3, show
that its gain will be 3 if . 5. For the Wien bridge oscillator of figure 3, compute the values of R and C
to produce an oscillation frequency of 5kHz (try different combinations of R and C ).
6. An oscillator circuit produces output without any input. Explain how.
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
36/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 35
EQUIPMENT REQUIRED:
DC Power Supply 741 IC Op-Amp Resistors (2x 1k , 10k , variable 10k , )
Capacitors (2x 0.1 F, 2x 0.47 F, 2x 1 F) Digital Multi-meter Oscilloscope.
EXPERIMENT PROCEDURE:
1- Construct the circuit as shown in figure 3. Use R and C as computed in pre-lab. Useand (variable).
2- Connect the Op-Amp DC supply voltage 15 V.3- Switch the DC supply ON.4- Connect the oscilloscope to display V Out .5- Vary the 10 k variable resistor so that oscillation can take place, you can observe
that on display of the oscilloscope (a sine wave is generated).6- Measure the frequency of oscillation OSC f and compare it with 5 kHz.7- Try different values of R and C . Compare the computed and measured frequencies.8- Record your results in following table and calculate the percentage error relative to
theoretical OSC f .
C
(F)
R
(k )Measured OSC f
(Hz)
TheoreticalRC2
1
=OSC f
(Hz) Error%
___________________________________ _______________Instructors Signature Date
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
37/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 36
LAB REVIEW QUESTIONS:
1. Write a short article (around one page) about the history of Wien bridgeoscillator.
2. Why the circuit shown in figure 1 is called a lead-lag circuit?3. Plot the magnitude of the transfer function verses frequency. Use the value
of R and C from pre-lab calculations. Make the plot on a semi-log graph paper. Use frequency ranges of 500 Hz to 50 kHz.
4. What should be the value of gain set by and to produce oscillations?What will happen if the gain set by and is not exactly correct?
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
38/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 37
EXPERIMENT #5
RC-PHASE-SHIFT OSCILLATOR USING BJT
OBJECTIVE:
At the completion of this experiment, students will be able to design andexperimentally verify the RC phase shift oscillator using 741 type op-amp for anoscillating frequency of 3 kHz.
THEORY/BACKGROUND:
We saw in previous experiment that a feedback circuit can produce sustainedoscillations, ifiii. Phase shift around feedback loop is zero degree andiv. The voltage gain around the feedback loop is one.
C1 C2 C3
R1 R2 R3
Rf
Vout
Figure 8. Op-amp based phase shift oscillator
In the above circuit, each RC pair introduces a phase shift between to (fordifferent frequencies). There would be a certain frequency (called resonancefrequency) at which the phase shift by three RC pairs would be 180 . The invertingamplifier provides a phase shift of another 180 . So the total phase shift becomes 360or . It can be shown that the gain introduced by the three stages of RC circuit is
. In order to compensate for this gain and produce sustained oscillations, the gain
set by and should be 29 i.e. . When this condition is fulfilled, the
circuit will start oscillating at a frequency where
and .
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
39/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 38
PRE-LAB:
The following pre-lab must be completed and submitted before the start of thisexperiment. The pre-lab is graded and is part of your lab grades.Solve the following exercises on separate sheets of paper and submit your solution
before the start of the lab experiment. You may need a copy of this pre-lab to compareyour solution with the lab experiment measurements.
1. For the circuit shown below, the transfer function is given by
Prove that this transfer function will be a real number if
which is called resonance frequency.
C1 C2 C3
R1 R2 R3
VoutVin
Figure 9. Three stage RC circuit used in phase-shift oscillator
2. Also show that the at resonance frequency the gain would be
3. Consider the phase-shift oscillator circuit of figure 1. Calculate the valuesof , to produce a resonance frequency of 3 kHz.
4. Calculate the value of to produce a gain of 29.5. Write a half page description of how this circuit produces sustained
oscillations.
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
40/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 39
EQUIPMENT REQUIRED:
DC Power Supply 741 IC Op-Amp Capacitors (3x 10nF, 3x 0.1 F, 3x 0.47 F, 1x +100 F)
Resistors (470 , 1k , 3x 3.3 k , 47k , variable 1M ) Digital multi-meter Oscilloscope.
EXPERIMENT PROCEDURE:
1. Construct the circuit as shown in figure 1. Use Rs and Cs as computed in pre-lab. Use the 1 M variable resistor for .
2. Connect the Op-Amp DC supply voltage 15 V.
3. Switch the DC supply ON .4. Connect the oscilloscope to display V Out .5. Vary the 1 M variable resistor so that oscillation can take place, you can
observe that on display of the oscilloscope (a sine wave is generated).6. Measure the frequency of oscillation OSC f and compare it with 3 kHz.
7. Try different values of R and C . Compare the computed and measuredfrequencies.
8. Record your results in following table and calculate the percentage errorrelative to theoretical OSC f .
Table-I: Frequency versus Capacitor Value
C(F)
R(k )
Measured OSC f
(Hz)
TheoreticalRC62
1
=OSC f
(Hz)
Error%
___________________________________ _______________Instructors Signature Date
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
41/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 40
LAB REVIEW QUESTIONS:
1- Can we implement an RC -phase-shift oscillator with less than three sections?Why?
2- Drive the expression for transfer function given in pre-lab. [Hint: checkAppendix B of your text book.]
3- The gain of the inverting amplifier set by and should be 29. Explainwhy?
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
42/43
Revised & Approved By: Electronics Sequence Committee, Date: Feb. 2011 Page 41
MINI-PROJECT 1
-
8/13/2019 Lab Manual for Electronic Circuits Final March 13 2011
43/43
MINI-PROJECT 2