the effect of recycled –polycarbonate ( pc ) mixing ratio on the tensile ...
Lab 6: Saturation & Atmospheric Stability. Review Lab 5 – Atm. Saturation Relative humidity?...
-
Upload
clifton-davidson -
Category
Documents
-
view
233 -
download
1
Transcript of Lab 6: Saturation & Atmospheric Stability. Review Lab 5 – Atm. Saturation Relative humidity?...
Lab 6: Saturation & Atmospheric
Stability
Review Lab 5 – Atm. Saturation
• Relative humidity?• Mixing ratio / saturation mixing ratio?
– Function of temp.. Clausius-Clapeyron curve– Sling psychrometer – what does this give us?
• Dew point?– Looking at RH equation above, when temp is reduced, all
else being equal, what happens to the RH of a sample of air? Does RH go up or down?
• Air is saturated when RH=100%
Lab 6• Lab 6: Saturation and Atmospheric Stability
– processes that influence atmospheric saturation – i.e., cause cooling and/or increase in water vapor content
– atmospheric processes that change either the temp and/or water vapor content of an air sample
– In this lab, we’ll focus on atmospheric mixing and adiabatic cooling and some processes that drive these conditions
Saturation & Atmospheric Stability
• Two main ways for air to reach saturation:1. Cooling to its dew point temperature (most
common)
2. Increasing water vapor content
RememberCondensation produces:1.Fog2.Dew3.Clouds
*ALL require saturated air to form!
RememberCondensation produces:1.Fog2.Dew3.Clouds
*ALL require saturated air to form!
1.
3.
2.
Atmospheric Mixing
• When two air masses of different temps and water vapor content mix
• When they mix, the new air mass will change in temp and water vapor – resulting in new mixing and saturation mixing
ratios – Changes relative humidity
Mixing Ratio = SMR * RH
“Uns
atur
ated
air”
0 –
99.9
% R
H
“Saturated air” 100% RH
Assuming the two mixing air masses are the same size and you know the temps and RH find: 1.The new temp of mixed air mass2.The new mixing ratio of the mixed air mass3.From the above, you can find the new RH (due to change in temp and water vapor)
Adiabatic Cooling
• Adiabatic temperature changes:– Temperature changes in which heat was neither added nor subtracted
(closed system)– Average internal energy decreases with expansion – changes in average
kinetic energy• Compressed air = warm air• Expanded air = cooler air
NOTE: If a parcel moves ↑, it passes through regions of
successively lower pressure:•Ascending air: EXPANDS
•Descending air: COMPRESSES
NOTE: If a parcel moves ↑, it passes through regions of
successively lower pressure:•Ascending air: EXPANDS
•Descending air: COMPRESSES
Saturation & Atmospheric Stability
DRY adiabatic rate: unsaturated• cools at a constant rate of
10°C/1km of ascent• warms at constant rate of
10°C/km of descent
WET adiabatic rate: saturated(has RH 100%)
• Slower rate of cooling caused by the release of latent heat
– Rates vary between 5°C & 9°C/1km
» Amount of LH released depends on quantity of moisture in the air
Dew Point rate:• 2°C/1km to the LCL• At the WALR after the LCL
LCL = altitude at which a parcel reaches saturation & cloud formation begins
Saturation & Atmospheric StabilityDALR = 10°C/1kmWALR = 5 – 9°C/1km
Parcel A Temperature (°C)
Height (km) Parcel B Temperature (°C)
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.0
0.5
28° surface 10°
LCL
WA
LR
Air decreases by 5°C
23°
18°
13° 1.5
10.5°
Air decreases by 2.5°C
DA
LR
• Lifting Condensation Level (LCL):– Reached when ascending air cools to its dew point
(saturation = 100% RH) – clouds form
– If it continues to rise:• Cools at the wet adiabatic lapse rate (between 5°& 9°C)
– Calculated based on:• Surface temperature & dew point temperature
Part II
Review
• What is adiabatic cooling?– Wet versus dry– Thinking about atmospheric saturation, how does
this influence cloud formation (hint: think about dew point temperature, etc.)
• What is environmental lapse rate?
• Atmospheric lifting forces:1. Surface heating (air expansion, less dense, rise,
etc..)2. Two surface air masses colliding (convergence)3. Contact of dissimilar air masses along warm &
cold fronts (convergence)4. Topographic barriers (e.g. orographic lift)5. Upper air divergence
• Rising air doesn’t mix substantially with the surrounding atmosphere. Once the initial lifting force stops, the continued rising of an air parcel depends on atmospheric stability (the state of the atmosphere surrounding the parcel).
Orographic Lifting
•Air ascends: adiabatic cooling often generates clouds & lots of precipitation
•Air descends: warms adiabatically, making condensation & precipitation less likely
LCL – T(°C) – Td(°C)/8 LCL – T(°C) – Td(°C)/8 25°C – 13°C = 12°C/8 = 1.5 km
LCL
Td (dew point) cools at:
• 2°C/km below the LCL•The WALR above the LCL
Td (dew point) cools at:
• 2°C/km below the LCL•The WALR above the LCL
Incorporating Dew Point
• Absolute stability:– Environmental lapse rate is less than the wet adiabatic rate
(surrounding air cools slower with height)– Stable air resists vertical movement, and doesn’t want to move. If it
gets forced above LCL it would remain cooler and return to surface– Note: air parcel cools faster than ELR
LAYERED CLOUDS not much vertical development
• Absolute instability:– Environmental lapse rate is greater than the dry adiabatic
rate (surrounding air cools faster w/ height)– Unstable air rises because of its buoyancy– Parcel of air cools slower than ELR
VERTICAL CLOUDS potential for thunderstorms
VERTICAL CLOUDS potential for thunderstorms
• Conditional stability:– Moist air has an environmental lapse rate
between the dry & wet adiabatic rates