KLARI-PROBES• All KLARI-PROBES have a memory device with a communication cable to the module....
Transcript of KLARI-PROBES• All KLARI-PROBES have a memory device with a communication cable to the module....
Stat
us J
anua
ry 2
019.
All
men
tione
d tra
dem
arks
or b
rand
s ar
e pr
oper
ty o
f the
cor
resp
ondi
ng o
wne
r. Su
bjec
t to
erro
r and
tech
nica
l cha
nges
.V21
KLARI-PROBES
Features
• KLARI-PROBES are the convenient measuring units for low voltage Klaric modules up to 80V.
• For current measurements the PROBES are equipped with low resistive accuracy resistors, for voltage measurements with voltage dividers. Temperature measurements are executed with PT1000 resistance thermometers which are also available in acid resistant version.
• All KLARI-PROBES have a memory device with a communication cable to the module. Therefore the configuration data (type, adjustment values, serial number etc.) are read out of the PROBE and transmitted to the module.
• The adjustment values are considered for the measurement result calculation. This implicates a very high degree of accuracy.
• Because the shunts only have marginal temperature drift, temperature compensation is not needed.
• A factory calibration is included in scope of delivery. On request we are pleased to offer a DAkkS calibration.
Versions
• LI-PROBES: These PROBES are used to measure currents in range of 0,25µA…150A (peak current). The user has to take care of protecting the measuring circuit.
• MICRO2- / MICRO3-PROBES: Current measurements at defined electric circuits inside vehicle fuse box. The measuring circuit/s is/are protected in the ranges of 5…30A by 1 or 2 FK1 fuse/s with the equivalent current value/s like the original fuse/s.
• FK1- / FK2- / FK3-PROBES: Current measurements at defined electric circuits inside vehicle fuse box. The measuring circuit is protected in the ranges of 5…70A by the original fuse.
• MCASE- / JCASE-PROBES: Current measurements at defined electric circuits inside vehicle fuse box. The measuring circuit is protected in the ranges of 20…60A by 1 JCASE fuse with the equivalent current value like the original fuse.
• HI-PROBES: Depending on the selected PROBE current measurements may be performed in ranges of 2,5mA…+7.200/-3.000A (peak current when using a 100μΩ-Shunt). The user has to take care of protecting the measuring circuit.
• U-PROBES: With these PROBES voltage measurements are available in ranges of 170µV…+/- 80V.
• LI/U-PROBES: These PROBES consist of a voltage and a current PROBEwith same potential. It allows current measuring in range of µA…150A (peak current) and also voltage measuring in range of mV…+/- 80V. The user has to take care of protecting the measuring circuit.
• HI/U-PROBES: These PROBES consist of a voltage and a current PROBE with same potential. It allows current measuring in range of µA…1.500A (peak current) and also voltage measuring in range of mV…+/- 1000V. The user has to take care of protecting the measuring circuit.
• T-PROBES: With these PROBES temperature measurements are available in range of -40…+105°C.
KLARI-FUSE 2 KLARI-MOD MC3 KLARI-CORD 4-Display
BF-Shunt FK-PROBE Special-PROBE
2
Stan
d Ja
nuar
201
2. A
lle e
rwäh
nten
Mar
ken-
ode
r War
enze
iche
n si
nd E
igen
tum
ihre
r jew
eilig
en B
esitz
er. I
rrtum
und
Tec
hnis
che
Ände
rung
en v
orbe
halte
n.
Stat
us J
anua
ry 2
019.
All
men
tione
d tra
dem
arks
or b
rand
s ar
e pr
oper
ty o
f the
cor
resp
ondi
ng o
wne
r. Su
bjec
t to
erro
r and
tech
nica
l cha
nges
.V21
KLARI-PROBES
COMBI-PROBES - LI/U - PROBES
HV-LI/U – PROBES consist of a voltage- and a current-PROBE.
Current measurement: • The measuring shunt is placed in a potted casing with cable lead-out for looping-in
the PROBE into the measuring circuit.
• The protection of the measuring circuit has to be provided by the user.
Voltage measurment: • The voltage is measured via a voltage divider.
• The input voltage is reduced to an allowed voltage level for the modules.
PROBE-construction:
potted casing with integrated shunt (type PBV) and voltage divider.
memory device, used for PROBE-identification and calibration data (placed in connector)
I-PROBE, measuring lines for measuring current = L1 (2 x 1m), heat resistant and highly flexible with loose cable ends
U-PROBE, connection-cable for measuring voltage = L3 (0,5m) with loose cable ends
data cable = L2 (1 / 3 / 5m) with 7-pin plug-connector
Caution: The maximum continuous current is lower than the measuring range.
Please refer to the user manual.
Nähere Informationen entnehmen Sie bitte dem Datenblatt.
L2
Shunt with voltage divider
L1 I- / U-
U+
I+
L3
CURRENT-PROBES type PBV
Gain
Measuring Range
[V DC]
Resolution/Bit
[mV/Bit] 100 0...+/- 9 0,3
40 0...+/- 27 0,9
25 0...+/- 42 1,4
5 0...+/- 80 7
1 - -
* indicated for the lowest measuring range ** at room temperature (23°C)
size (l/w/h):50x40x16 mm
VOLTAGE-PROBES type 80V
Ordering: <name> - <resistance value> - <L1> - <L2> - <L3> LI/U - 1000 / … / 2 - 1 - 1 / 3 / 5 - 0,5
Resistor
[mΩ]
Measuring range
[A]
Resolution/Bit*
[mA]
Maximum permanent current**
[A] 1000 -0,3…+0,72 0,25 0,72
500 -0,6…+1,44 0,5 1,44
100 -3…+7,2 2,5 6,5
50 -6…+14,4 5 9,5
25 -12…+28,8 10 12
10 -30…+72 25 21
5 -60…+144 50 25
2 -150…+360 125 40
3
Stan
d Ja
nuar
201
2. A
lle e
rwäh
nten
Mar
ken-
ode
r War
enze
iche
n si
nd E
igen
tum
ihre
r jew
eilig
en B
esitz
er. I
rrtum
und
Tec
hnis
che
Ände
rung
en v
orbe
halte
n.
Stat
us J
anua
ry 2
019.
All
men
tione
d tra
dem
arks
or b
rand
s ar
e pr
oper
ty o
f the
cor
resp
ondi
ng o
wne
r. Su
bjec
t to
erro
r and
tech
nica
l cha
nges
.V21
KLARI-PROBES
COMBI-PROBES - I/U-BF1 – PROBES HV-I/U – PROBES consist of a voltage- and a current-PROBE.
Current measurement: • The measuring shunt is placed via mounting straps directly into the measuring circuit
• The protection of the measuring circuit has to be provided by the user
Voltage measurment: • The voltage is measured via a voltage divider
• The input voltage is reduced to an allowed voltage level for the modules
PROBE-construction:
shunt (type BF1) with mounting straps (temperature range -40…+130°C) and voltage divider
memory device, used for PROBE-identification and calibration data (placed in connector)
U-connection-cable = L3 (0,5m), heat resistant and highly flexible with loose cable ends
data cable = L2 (1 / 3 / 5m) with 7-pin plug-connector
Caution: The maximum continuous current is lower than the measuring range.
Please refer to the user manual.
CURRENT-PROBES type BF1
VOLTAGE-PROBES type 80V
Resistor
[mΩ]
Measuring range
[A]
Resolution/Bit*
[mA]
Maximum permanent current**
[A] 2 -150…360 0,125 60
1 -300…+720 0,25 80
0,5 -600…+1440 0,5 120
0,2 -1500…+3600 1,25 150
* indicated for the lowest measuring range
Gain
Measuring range
[V DC]
Resolution/Bit
[mV/Bit] 100 0...+/- 9 0,3
40 0...+/- 27 0,9
25 0...+/- 42 1,4
5 0...+/- 80 7
1 - -
Ordering: <name> - <resistance value> - <L1> - <L2> - <L3> I/U-BF1 - 2 / … / 0,2 - 0 - 1 / 3 / 5 - 0,5
I- U-
U+
Shunt with voltage divider
L2
L3
I+
4
Stan
d Ja
nuar
201
2. A
lle e
rwäh
nten
Mar
ken-
ode
r War
enze
iche
n si
nd E
igen
tum
ihre
r jew
eilig
en B
esitz
er. I
rrtum
und
Tec
hnis
che
Ände
rung
en v
orbe
halte
n.
Stat
us J
anua
ry 2
019.
All
men
tione
d tra
dem
arks
or b
rand
s ar
e pr
oper
ty o
f the
cor
resp
ondi
ng o
wne
r. Su
bjec
t to
erro
r and
tech
nica
l cha
nges
.V21
KLARI-PROBES
COMBI-PROBES - I/U-BF2 – PROBES HV-I/U – PROBES consist of a voltage- and a current-PROBE.
Current measurement: • The measuring shunt is placed via mounting straps directly into the measuring circuit
• The protection of the measuring circuit has to be provided by the user
Voltage measurment: • The voltage is measured via a voltage divider
• The input voltage is reduced to an allowed voltage level for the modules
PROBE-construction:
shunt (type BF2) with mounting straps (temperature range -40…+130°C) and voltage divider memory device, used for PROBE-identification and calibration data (placed in connector)
U-connection-cable = L3 (0,5m), heat resistant and highly flexible with loose cable ends
data cable = L2 (1 / 3 / 5m) with 7-pin plug-connector
Caution: The maximum continuous current is lower than the measuring range.
Please refer to the user manual.
CURRENT-PROBES type BF2
VOLTAGE-PROBES type 80V
Ordering: <name> - <resistance value> - <L1> - <L2> - <L3> I/U-BF2 - 2 / … / 0,1 - 0 - 1 / 3 / 5 - 0,5
Resistor
[mΩ]
Measuring range
[A]
Resolution/Bit*
[mA]
Maximum permanent current**
[A] 2 -150…360 0,125 60
1 -300…+720 0,25 80
0,5 -600…+1440 0,5 130
0,2 -1500…+3600 1,25 180
0,1 -3000…+7200 2,5 310
the shunts are linked with a copper bar 20x3,5x200mm * indicated for the lowest measuring range
** at room temperature (23°C)
Gain
Measuring range
[V DC]
Resolution/Bit
[mV/Bit] 100 0...+/- 9 0,3
40 0...+/- 27 0,9
25 0...+/- 42 1,4
5 0...+/- 80 7
1 - -
I- U-
U+
Shunt mit Spannungs-
teiler
L2
L3
I+
5
Stat
us J
anua
ry 2
019.
All
men
tione
d tra
dem
arks
or b
rand
s ar
e pr
oper
ty o
f the
cor
resp
ondi
ng o
wne
r. Su
bjec
t to
erro
r and
tech
nica
l cha
nges
.V21
KLARI-PROBES
LI - PROBES
Measuring unit with cable lead-out for looping the PROBE into the measuring circuit. The protection of the
measuring circuit has to be provided by the user. The shunt is integrated in a grouted casing.
Construction: cable lead-out = L1 (1m), (heat resistant and highly flexible) with loose cable ends
grouted casing with integrated shunt
data cable = L2 (1…5 m) with 6-pin push-pull connector
memory device, used for PROBE-identification and calibration data
Caution: The maximum continuous current is lower than the measuring range.
Please refer to the user manual.
LI - PROBES
Ordering: <name> - <resistance value> - <L1> - <L2> - <L3> LI - 1000 / … / 2 - 1 - 1…5 - 0
Resistor
[mOhm]
Measuring range
[A]
Resolution/Bit*
[µA]
Maximum permanent current **
[A] 1000 -0,3…+0,72 0,25 0,72
500 -0,6…+1,44 0,5 1,44
100 -3…+7,2 2,5 6,5
50 -6…+14,4 5 9,5
25 -12…+28,8 10 12
10 -30…+72 25 21
5 -60…+144 50 25
2 -150…+360 125 40
* indicated for the lowest measuring range ** at room temperature (23°C) size (l/w/h): 50x40x16mm
L1 L2
6
Stat
us J
anua
ry 2
019.
All
men
tione
d tra
dem
arks
or b
rand
s ar
e pr
oper
ty o
f the
cor
resp
ondi
ng o
wne
r. Su
bjec
t to
erro
r and
tech
nica
l cha
nges
.V21
KLARI-PROBES
MICRO2 - PROBES
Measuring unit with MICRO2 connector, which is plugged into the vehicle’s fuse holder instead of the
original fuse. The measuring circuit is protected by a FK1 fuse with the equivalent current value to ensure
that the measuring circuit is protected. The FK1 fuse is plugged into the fuse holder at the aluminium
casing. The measuring shunt is integrated in the casing.
Construction: MICRO2 connector
cable with fuse = L1 (highly flexible and heat resistant)
aluminium casing with integrated shunt and fuse holder for measuring circuit protection
data cable = L2 (1…5m) with 6-pin push-pull-connector
memory device, used for PROBE-identification and calibration data
Caution: The maximum continuous current may be lower than the measuring range.
Please refer to the user manual.
MICRO2 - PROBES
Ordering: <name> - <fuse value> - <L1> - <L2> - <L3> MICRO2 - 5 / … / 30 - 1 / 3 - 1…5 - 0
Type
Measuring range
[A] Resolution/Bit*
[µA] R
[mΩ]
Cross section [mm2]
5 A 5 10 25 1,5
10 A 10 25 10 2,5
20 A 20 50 5 4
30 A 30 125 2 4
size (l/w/h): 50x41x20mm
* indicated for the lowest measuring range
L1
L2
FK1- fuse holder
measuring shunt
7
Stat
us J
anua
ry 2
019.
All
men
tione
d tra
dem
arks
or b
rand
s ar
e pr
oper
ty o
f the
cor
resp
ondi
ng o
wne
r. Su
bjec
t to
erro
r and
tech
nica
l cha
nges
.V21
KLARI-PROBES
MICRO3 - PROBES
Measuring unit with MICRO3 connector, which is plugged into the vehicle’s fuse holder instead of the
original fuse. The measuring circuits are protected by 2 FK1 fuses with the equivalent current values to
ensure that the measuring circuits are protected. The FK1 fuses are plugged into the fuse holders at the
aluminium casing. The 2 measuring shunts are integrated in the casing.
Construction: MICRO3 connector
cable with fuse = L1 (highly flexible and heat resistant)
aluminium casing with integrated 2 shunts and 2 fuse holders for measuring circuit protection
data cable = L2 (1…5m) with 6-pin push-pull-connector
memory device, used for PROBE-identification and calibration data
Caution: The maximum continuous current may be lower than the measuring range.
Please refer to the user manual.
MICRO3 - PROBES
Ordering: <name> - <fuse value> - <L1> - <L2> - <L3> MICRO3 - 5 / 10 - 1 / 3 - 1…5 - 0
Type
Measuring range
[A] Resolution/Bit*
[µA] R
[mΩ]
Cross section [mm2]
5 A 5 10 25 1,5
10 A 10 25 10 2,5
20 A 20 50 5 4
size (l/w/h): 80x55x24mm
* indicated for the lowest measuring range
L1
L2
2 FK1 fuse holder
L2
measuring- shunt
measuring- shunt
8
Stat
us J
anua
ry 2
019.
All
men
tione
d tra
dem
arks
or b
rand
s ar
e pr
oper
ty o
f the
cor
resp
ondi
ng o
wne
r. Su
bjec
t to
erro
r and
tech
nica
l cha
nges
.V21
KLARI-PROBES
Type
Measuring range
[A] Resolution/Bit*
[µA] RNenn
[mΩ]
Cross section [mm2]
5 A 5 10 25 1,5
10 A 10 25 10 2,5
20 A 20 50 5 4
30 A 30 125 2 4
size (l/w/h): 50x41x20mm
* indicated for the lowest measuring range
FK - PROBES
Measuring unit with FK1-, FK2- or FK3-connector, which is plugged into the vehicle’s fuse holder instead
of the original fuse. The original fuse has to be plugged into the PROBE’s fuse holder to ensure that the
measuring circuit is protected. The fuse holder and the shunt are integrated in a small aluminum casing.
Construction: FK1-, FK2-, FK3- connector
cable with fuse = L1 (highly flexible and heat resistant)
aluminium casing with integrated shunt and fuse holder for measuring circuit protection
data cable = L2 (1…5m) with 6-pin push-pull-connector.
memory device, used for PROBE-identification and calibration data.
Caution: The maximum continuous current may be lower than the measuring range.
Please refer to the user manual.
FK1 - PROBES
Ordering: <name> - <fuse value> - <L1> - <L2> - <L3> FK1 - 5 / … / 30 - 1…3 - 1…5 - 0
L1
L2
FK fuse holder measuring- shunt
9
Stat
us J
anua
ry 2
019.
All
men
tione
d tra
dem
arks
or b
rand
s ar
e pr
oper
ty o
f the
cor
resp
ondi
ng o
wne
r. Su
bjec
t to
erro
r and
tech
nica
l cha
nges
.V21
KLARI-PROBES
FK2 - PROBES
FK3 - PROBES
Type
Measuring range
[A] Resolution/Bit*
[µA] RNenn
[mΩ]
Cross section [mm2]
5 A 5 10 25 1,5
10 A 10 25 10 2,5
20 A 20 50 5 4 size (l/w/h): 50x41x20mm
Type
Measuring range
[A] Resolution/Bit*
[µA] RNenn
[mΩ]
Cross section [mm2]
30 A 30 125 2 4
40 A 40 250 1 4
size (l/w/h): 80x55x24mm
* indicated for the lowest measuring range
Ordering: <name> - <fuse value> - <L1> - <L2> - <L3> FK2 - 5 / … / 40 - 1…3 - 1…5 - 0
Ordering: <name> - <fuse value> - <L1> - <L2> - <L3> FK3 - 30 / 50 / 70 - s.table - 1…5 - 0
Type
Measuring range
[A] Resolution/Bit*
[µA] RNenn
[mΩ] L1
[m]
Cross section [mm2]
30 A 30 125 2 1 / 3 4
50 A 50 250 1 1 6
70 A 70 500 0,5 0,5 6
size (l/w/h): 80x55x24mm
* indicated for the lowest measuring range
10
Stat
us J
anua
ry 2
019.
All
men
tione
d tra
dem
arks
or b
rand
s ar
e pr
oper
ty o
f the
cor
resp
ondi
ng o
wne
r. Su
bjec
t to
erro
r and
tech
nica
l cha
nges
.V21
KLARI-PROBES
JCASE - and MCASE - PROBES
Measuring unit with JCASE or MCASE connector, which is plugged into the vehicle’s fuse holder instead
of the original fuse. The measuring circuit is protected by a JCASE fuse with the equivalent current value
to ensure that the measuring circuit is protected. The JCASE fuse is plugged into the fuse holder at the
aluminium casing. The measuring shunt is integrated in the casing.
Construction: JCASE or MCASE connector
cable with fuse = L1 (highly flexible and heat resistant)
aluminium casing with integrated shunt and fuse holder for measuring circuit protection
data cable = L2 (1…5m) with 6-pin push-pull-connector
memory device, used for PROBE-identification and calibration data
Caution: The maximum continuous current may be lower than the measuring range.
Please refer to the user manual.
L1
L2
JCASE fuse holder
measuring-shunt
Type
Measuring range
[A]
Resolution/Bit*
[µA]
R
[mΩ]
L1
[m]
Cross section
[mm2] JCASE 20 50 5 1 / 3 2x2,5 / 4
JCASE 30 125 2 1 / 3 2x2,5 / 4
JCASE 40 250 1 1 / 3 2x2,5 / 4
size (l/w/h): 80x55x24 mm
Type
Measuring range
[A]
Resolution/Bit*
[µA]
R
[mΩ]
L1
[m]
Cross section
[mm2] JCASE 50 250 1 1 6
JCASE 60 500 0,5 0,5 6
size (l/w/h): 80x105x26mm
* indicated for the lowest measuring range
JCASE - PROBES
Bestellung: <Name> - <Sicherungswert> - <L1> - <L2> - <L3> JCASE - 20 / … / 60 - s.Tab. - 1…5 - 0
11
Stat
us J
anua
ry 2
019.
All
men
tione
d tra
dem
arks
or b
rand
s ar
e pr
oper
ty o
f the
cor
resp
ondi
ng o
wne
r. Su
bjec
t to
erro
r and
tech
nica
l cha
nges
.V21
KLARI-PROBES
Type
Measuring range
[A]
Resolution/Bit*
[µA]
R
[mΩ]
L1
[m]
Cross section
[mm2] MCASE 20 50 5 1 / 3 2,5
MCASE 30 125 2 1 / 3 2,5
MCASE 40 250 1 1 / 3 2,5
size (l/w/h): 80x55x24 mm
Type
Measuring range
[A]
Resolution/Bit*
[µA]
R
[mΩ]
L1
[m]
Cross section
[mm2] MCASE 50 250 1 0,5 2,5 / 4
MCASE 60 500 0,5 0,5 2,5 / 4
size (l/w/h): 80x105x26mm
* indicated for the lowest measuring range
MCASE - PROBES
Ordering: <name> - <fuse value> - <L1> - <L2> - <L3> MCASE - 20 / … / 60 - s.table - 1…5 - 0
12
Stat
us J
anua
ry 2
019.
All
men
tione
d tra
dem
arks
or b
rand
s ar
e pr
oper
ty o
f the
cor
resp
ondi
ng o
wne
r. Su
bjec
t to
erro
r and
tech
nica
l cha
nges
.V21
KLARI-PROBES
HI – PROBES (without measuring circuit protection) At these PROBEs the shunt has to be placed directly into the measuring circuit.
The protection of the measuring circuit has to be provided by the user.
Construction: Shunt (type BF1 or BF2) with mounting straps (temperature range -40…+130°C)
data cable = L2 (1…5m) with 6-pin push-pull connector
memory device, used for PROBE identification and calibration data
Caution: The maximum continuous current is lower than the measuring range.
Please refer to the user manual.
L2
HIGH-CURRENT - PROBES
BF 1
BF 2
Ordering: <name> - <resistance value> - <L1> - <L2> - <L3> HI-BF1 - 2 / … / 0,2 - 0 - 1…5 - 0 HI-BF2 - 2 / … / 0,1 - 0 - 1…5 - 0
Resistor
[mΩ]
Measuring range
[A]
Resolution/Bit*
[mA]
Maximum permanent current**
[A] 2,5 -120…+288 0,1 60
1 -300…+720 0,25 80
0,5 -600…+1440 0,5 120
0,2 -1500…+3600 1,25 150
size (l/w/h): 42x16x15mm the shunts are linked with a copper bar 20x3x200mm * indicated for the lowest measuring range ** at room temperature (23°C)
Resistor
[mΩ]
Measuring range
[A]
Resolution/Bit*
[mA]
Maximum permanent current**
[A] 2 -150…360 0,125 80
1 -300…+720 0,25 120
0,5 -600…+1440 0,5 130
0,2 -1500…+3600 1,25 180
0,1 -3000…+7200 2,5 310
size (l/w/h): 68x27x15mm the shunts are linked with a copper bar 20x3,5x200mm * indicated for the lowest measuring range ** at room temperature (23°C)
13
Stat
us J
anua
ry 2
019.
All
men
tione
d tra
dem
arks
or b
rand
s ar
e pr
oper
ty o
f the
cor
resp
ondi
ng o
wne
r. Su
bjec
t to
erro
r and
tech
nica
l cha
nges
.V21
KLARI-PROBES
HI
grouted HI-PROBE
Various resistors and PROBE types available. We would be pleased to help you finding the appropriate PROBE for your measuring task.
BF3 - SHUNT
Resistor
[mΩ]
Measuring range
[A]
Resolution/Bit*
[mA]
Maximum permanent current**
[A] 0,05 -6000…+8000 5 300
0,025 -8000…+8000 10 420
HI-SPECIAL-PROBES
Resistor
[mΩ]
Measuring range
[A]
Resolution/Bit*
[mA]
Maximum permanent
current shunt**
[A] 0,2 -1500…3600 1,25 150
0,1 -3000…+7200 2,5 250
0,05 -6000…+8000 5 300
0,025 -8000…+8000 10 400
size: (l/w/h): 150x65x40mm (without cables) * indicated for the lowest measuring range ** at room temperature (23°C) the maximum permanent current is limited by the cross-section
of the connected cables L1:
selectable: 35mm2 / 70mm2 allowed max. permanent current at 80°C: 200A / 305A - for installation in a drug battery-box instead of the stud between the batteries - Standard connection cable shoe, other connections after consultation with us
size: (l/w/h): 90x42x15mm the shunts are linked with a copper bar 20x3x200mm * indicated for the lowest measuring range ** at room temperature (23°C)
Ordering: <name> - <resistance value> - <L1> - <L2> - <L3>
HI-BF3 - 0,05 / 0,025 - 0 - 1…5 - 0
Ordering: <name> - <resistance value> - <L1> - <L2> - <L3> HI-SPECIAL - 0,2 / … / 0,025 - 0,7 - 1…5 - 0
14
Stat
us J
anua
ry 2
019.
All
men
tione
d tra
dem
arks
or b
rand
s ar
e pr
oper
ty o
f the
cor
resp
ondi
ng o
wne
r. Su
bjec
t to
erro
r and
tech
nica
l cha
nges
.V21
KLARI-PROBES
ACCESSORIES
T - PROBE (acid-resistant) PT1000 sensor for temperature measurements
temperature measuring range: -40 to +105°C
data cable = L2 (1…5m)
PT1000 sensor cable = L1 (2m)
U - PROBE voltage measuring unit
measuring range +/-80V
resolution: 170µV/Bit
data cable: 1m
measuring cable: See below / depends on variant
total length: data cable + measuring cable
Gain
Measuring range
[V]
Resolution/Bit*
[µV] 100 +/- 5 170
50 +/- 10 340
24 +/- 20 680
6 +/- 80 2720
* indicated for the lowest measuring range
Extension cable for the PROBES
Ordering: <name> - <L1> - <L2> - <L3> T-80V - 2 - 1…5 - 0
Ordering: <name> - <L1> - <L2> - <L3> U-80V - 1…5 - 1 - 0
Ordering: <name> - <L1> - <L2> - <L3> PROBE-EXT-80V - 0 - 2 / 4 - 0