K-1044T SHEET SOFTresources.kohler.com/plumbing/kohlerapac/pdf/1044T.pdfRIM OF LAVATORY 615mm 310mm...
Transcript of K-1044T SHEET SOFTresources.kohler.com/plumbing/kohlerapac/pdf/1044T.pdfRIM OF LAVATORY 615mm 310mm...
-
RIM OF LAVATORY
615mm
310m
m
CAST IRON VESSEL/
CUT-OUT TEMPLATE / INSTALLATION INSTRUCTIONS
K-1044TSHEET SOFT
BEFORE YOU BEGIN�
�
�
�
�
�
�
�
Observe all local plumbing and building codes.Check waste pipe and supply pipe. Replace ifnecessary.Use these instructions for above-counter installation.Please follow the instructions that apply to yourinstallation.You can choose between a wall-mount or countertopfaucet installation, depending upon the setting andstyling you desire. We recommend a wall-mountfaucet.Prior to installation, unpack the new lavatory andcarefully inspect it for damage. Return the lavatory toits protective carton until you are ready to install it.All information in these instructions is based uponthe latest product information available at the time ofpublication. Kohler China reserves the right to makechanges in product characteristics, packaging, oravailability at any time without notice.These instructions contain important care, cleaning,and warranty information. Please leave theseinstructions for the consumer.The vessel weighs 18kg.
TOOLS AND MATERIALS
REQUIRED(NOT SUPPLIED)
�
�
�
�
�
�
�
�
�
�
SealantTemplate (supplied)Safety glassesPencilScissorsTape MeasureHole SawKeyhole saw or saber sawDrill (1/2" dia. Drill bit, or larger)Screwdriver
�
�
�
�
�
�
�
�
�
�
( )
( 13mm )
�
�
�
�
�
�
�
� 18kg
Roughing-In Notes
Fixture dimensions are nominal and conformto tolerances in ASME Standard A112.19.2.
(T) Pop-up drain 238mm.
(S) 356mm: (Based on 305mm riser whichmay require cutting).
Minimum 50mm distance from water streamto the vessel rim edge when installed withcenterline as shown.
Conform to tolerances in ASME StandardA112.1.2, spout must be tall enough to clear76mm rim height(vertical distance from top ofthe vessel to spout)and provide 25mm airgap.
(ASME)A112.19.2
(T) 238mm
(S) 356mm 305mm
50mm
76mm() ASME A112.1.2
25mm
�
�
, 2014Copyright Kohler China Ltd., 2014
1240414-T01-A
Cut out the opening by carefullyfollowing the pencil line.
Large lavatories are veryheavy. Get help lifting thelavatory into place.
Verify proper clearance betweenthe lavatory, faucet, andbacksplash.Remove the lavatory from thecountertop cutout, and return it toits protective carton. Do not standor store the lavatory on the drainsurface.
CAUTION: Risk of
personal injury or
product damage.
Fig.#44
Drill the faucet holes.
Install the faucet to the countertopaccording to the manufacturer'sinstructions.
For tile, wood, or other porousmaterials, apply waterproofsealant around the cutout area ofthe countertop surface. Follow allmanufacturer's instructions andwarnings. Allow the sealant todry before proceeding.
INSTALLATIONS
Position the template on thecountertop.
Besure to provide sufficient spoutoverhang into the lavatory basin.See the roughing-in notes forminimum spout length information.
Payspecial attention to the spout andhandle fit clearance when locatingthe faucet, as noted below. Usethe template to locate the faucetspout hole centerline on thecountertop. This centerline isrecommended to provideadequate clearance between theedge of the lavatory and thespout.Check for adequate clearancebetween the backsplash or wallfaucet spout and handles, andlavatory. We recommendclearance of at least 25mmbetween:
The installed lavatory and thefaucet spout.The installed lavatory and theend of the faucet handles, and.The faucet spout and handlesand the backsplash or wall.
In china installation willnot have separate backsplash.The back wall is the "backsplash".Refer to the faucet installationinstructions for required clearance,and mark the preferred faucethole locations using a soft leadpencil.Trace the template on thecountertop using a soft leadpencil.
For Wall-mount faucets:
For Countertop Faucets:
NOTE:
�
�
�
25mm
�
�
�
25mm Min.Clearance
25mm
SpoutCenterline Backsplash
Fig.#22
Fig.#33
AdhesiveSealant
Fig.#55
CUT ALONG THIS LINE
72m
m
72mm
70
9
ROUGHING-IN
Kohler reserves the right to change marked dimensions without prior notice.
Reference Value UNIT: mm
Loosely apply the adhesivesealant around the entirecountertop cutout so it isalongside the cutout hole. Adjustthe placement of the sealantbefore removing the backingmaterial. Cut off any excess sealmaterial. Carefully remove theadhesive seal backing material.
615143
43
310
864
74133
TS
686
203
200610
152
229
32
10210210
368 201419
CAUTION: Risk of
personal injury or
product damage.
Note:
Large lavatories are veryheavy. Get help lifting thelavatory into place.
The countertop should bestrengthened at its back to bemore than 300mm x 300mm.Carefully put the vessel into thecutout and fix with screw bolts.
The countertop should bestrengthened to be more than300mmx300mm.
Fix the vessel by inserting the 4screws through the countertopand the supporting board.
300mm x 300mm
300mmx300mm.
4
Fig.#66
Connect the faucet supply lines.
Connect tale piece of drain.Screw tight the tale piece of drainprovided to the bottom of thedrain. Use rubber gasket toprevent leakage.
Connect the drain assembly.
Open the faucet valves, andcheck for leakage.
Clean up with a non-abrasivecleaner.
NutGaskeet
Tale Piece of Drain
Nut
Gasket
Fig.#88
Fig.#77
CARE AND CLEANING
To keep your lavatory looking new, make sure yourinse it out thoroughly after each use.
on this product, as they will scratchand ruin the surface. Stubborn stains, paint, or tarcan be removed with turpentine or paint thinner.
DO NOT USE
ABRASIVES
Supporting Board
/ColorImageDict > /JPEG2000ColorACSImageDict > /JPEG2000ColorImageDict > /AntiAliasGrayImages false /CropGrayImages true /GrayImageMinResolution 300 /GrayImageMinResolutionPolicy /OK /DownsampleGrayImages true /GrayImageDownsampleType /Bicubic /GrayImageResolution 300 /GrayImageDepth -1 /GrayImageMinDownsampleDepth 2 /GrayImageDownsampleThreshold 1.50000 /EncodeGrayImages true /GrayImageFilter /DCTEncode /AutoFilterGrayImages true /GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict > /GrayImageDict > /JPEG2000GrayACSImageDict > /JPEG2000GrayImageDict > /AntiAliasMonoImages false /CropMonoImages true /MonoImageMinResolution 1200 /MonoImageMinResolutionPolicy /OK /DownsampleMonoImages true /MonoImageDownsampleType /Bicubic /MonoImageResolution 1200 /MonoImageDepth -1 /MonoImageDownsampleThreshold 1.50000 /EncodeMonoImages true /MonoImageFilter /CCITTFaxEncode /MonoImageDict > /AllowPSXObjects false /CheckCompliance [ /None ] /PDFX1aCheck false /PDFX3Check false /PDFXCompliantPDFOnly false /PDFXNoTrimBoxError true /PDFXTrimBoxToMediaBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXSetBleedBoxToMediaBox true /PDFXBleedBoxToTrimBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXOutputIntentProfile () /PDFXOutputConditionIdentifier () /PDFXOutputCondition () /PDFXRegistryName () /PDFXTrapped /False
/Description > /Namespace [ (Adobe) (Common) (1.0) ] /OtherNamespaces [ > /FormElements false /GenerateStructure true /IncludeBookmarks false /IncludeHyperlinks false /IncludeInteractive false /IncludeLayers false /IncludeProfiles true /MultimediaHandling /UseObjectSettings /Namespace [ (Adobe) (CreativeSuite) (2.0) ] /PDFXOutputIntentProfileSelector /NA /PreserveEditing true /UntaggedCMYKHandling /LeaveUntagged /UntaggedRGBHandling /LeaveUntagged /UseDocumentBleed false >> ]>> setdistillerparams> setpagedevice