JUNCTION FIELD EFFECT TRANSISTOR(JFET). JFET operation can be compared to a water faucet : The...

JUNCTION FIELD EFFECT TRANSISTOR(JFET)

JFET operation can be compared to a water faucet :

The source of water pressure – accumulated electrons at the negative pole of the applied voltage from Drain to Source

The drain of water – electron deficiency (or holes) at the positive pole of the applied voltage from Drain to Source.

The control of flow of water – Gate voltage that controls the width of the n-channel, which in turn controls the flow of electrons in the n-channel from source to drain.

JFETs and Their Characteristics

Fig. (a) Fig. (b)

Fig. (a) is the schematic symbol for the n-channel JFET, and Fig. (b) shows the symbol for the p-channel JFET. The only difference is the direction of the arrow on the gate lead.

JFETs and Their Characteristics

JFETN-Channel P-

Channel

Transfer Characteristics

The transfer characteristic of input-to-output is not as straight forward in a JFET as it was in a BJT.

In a BJT, indicated the relationship between IB (input) and IC (output).

In a JFET, the relationship of VGS (input) and ID (output) is a little more complicated:

2

P

GSDSSD )

V

V(1II

Transfer Characteristics

From this graph it is easy to determine the value of ID for a given value of VGS.

Plotting the Transfer Curve

Shockley’s Equation Methods. Using IDSS and Vp (VGS(off)) values found in a specification sheet, the Transfer

Curve can be plotted using these 3 steps:

Step 1:

Solving for VGS = 0V:

Step 2:

Solving for VGS = Vp (VGS(off)):

Step 3:

Solving for VGS = 0V to Vp:

Plotting the Transfer Curve

Shorthand method

VGS ID0 IDSS

0.3VP IDSS/2

0.5 IDSS/4

VP 0mA

JFET Symbols

Basic Operation Characteristics And Parameters

Pinch-Off Voltage

VGS Controls ID

Cutoff Voltage JFET Transfer Characteristic JFET Forward Transconductance Input Resistance and Capacitance Drain-to-Source Resistance

JFET BIASING Fixed– Bias Self-Bias

Setting the Q-Point of a Self-Biased JFET Midpoint Bias Graphical Analysis of a Self-Biased JFET

Voltage-Divider Bias Graphical Analysis of a JFET with Voltage-Divider Bias Q-Point Stability

The Drain Characteristic Curve when VGS = 0 V

A

B C

Ohmicregion

Constant-current region

Breakdown

IDSS

ID

VDSVp (pinch-off voltage)

VGS = 0

A Biased n-channel JFET

VGS = 0V and VDS = 0V

VGS = -0.5V and VDS = 0V

VGS = -1V and VDS = 0V

IDSS is Drain to Source current with gate

Shorted. VGS(off) is the value of VGS that makes ID

approximately zero is the cutoff voltage. Vp, pinch-off voltage, is the value of VDS at

which ID becomes constant . VGS(off) and Vp are always equal in

magnitude but opposite in sign.

VGS(off) = - 4 and IDSS = 12mA Determine the minimum value of VDD to put the

device in the constant current region operation.

VGS(off) = - 4 and IDSS = 12mA Determine the minimum value of VDD to put the

device in the constant current region operation. Since VGS(off) = - 4V, Vp = 4V. VDS = Vp=4V, VGS = 0 V ID = IDSS = 12 mA VRD = IDRD =(12mA)(560 Ohm) = 6.72 V VDD = VDS + DRD = 4 V + 6.72 V = 10.7 V

2

P

GSDSSD )

V

V(1II

Example of An n-channel JFET transfer characteristic curve

2

P

GSDSSD )

V

V(1II

Questions

VGS(off) = - 8 V and IDSS = 9 mA Determine the drain current, ID for VGS = 0 V,

VGS = - 1 V, and VGS = -4 V

using this formula

2

P

GSDSSD )

V

V(1II

Answers ID = IDSS (1 - ( VGS/VGS(off)) )^2For VGS = 0 VID = 9 mA (1 - ( 0/-8) )^2 = 9 mA

For VGS = -1 VID = 9 mA (1 - ( -1/-8) )^2 = 6.89 mA

For VGS = -4 VID = 9 mA (1 - ( -4/-8) )^2 = 2.25 mA

JFET Forward Transconductance

Transconductance formulas

gm0 = (2Idss/( |Vgs(off)| )) gm = gm0 (1-Vgs/ Vgs(off)) Unit for transconductance, gm, is

siemens (S)

Fixed-Bias

Investigating the input loop

IG=0A, therefore

VRG=IGRG=0V

Applying KVL for the input loop,

-VGG-VGS=0

VGG= -VGS

It is called fixed-bias configuration due to VGG is a fixed

power supply so VGS is fixed

The resulting current,

2)1(P

GSDSSD V

VII

Investigating the graphical approach. Using below tables, we can draw the graph

VVGSGS IIDD

00 IIDSSDSS

0.3V0.3VPP IIDSSDSS/2/2

0.50.5 IIDSSDSS/4/4

VVPP 0mA0mA

The fixed level of VGS has been superimposed as a vertical

line at

At any point on the vertical line, the level of VG is -VGG--- the

level of ID must simply be determined on this vertical line.

The point where the two curves intersect is the common

solution to the configuration – commonly referrers to as the

quiescent quiescent or operating point.

The quiescent level of ID is determine by drawing a

horizontal line from the Q-point to the vertical ID axis.

Output loop

DDDDDS RIVV

VVS 0

SDDS VVV

SDSD VVV 0SV

DSD VV

SGGS VVV

SGSG VVV 0SV

GSG VV

Determine VGSQ, IDQ, VDS, VD, VG, VS

Exercise

Determine IDQ, VGSQ, VDS, VD, VG and VS

Self Bias

The self-bias configuration eliminates the need for two dc supplies.

The controlling VGS is now determined by the voltage across the resistor RS

For the indicated input loop:

Mathematical approach:

rearrange and solve.

SDGS RIV

2

2

1

1

P

SDDSSD

P

GSDSSD

V

RIII

V

VII

Graphical approach

Draw the device transfer characteristic Draw the network load line

Use to draw straight line. First point, Second point, any point from ID = 0 to ID = IDSS. Choose

the quiescent point obtained at the intersection of the straight line plot and the device characteristic curve.

The quiescent value for ID and VGS can then be determined and used to find the other quantities of interest.

SDGS RIV 0,0 GSD VI

2

2

SDSSGS

DSSD

RIV

thenI

I

For output loop

Apply KVL of output loop Use ID = IS

RDDDSDSD

SDS

DSDDDDS

VVVVV

RIV

RRIVV

)(

Determine VGSQ, IDQ,VDS,VS,VG and VD.

Example Determine VGSQ, IDQ, VD,VG,VS and VDS.

Voltage-Divider Bias

The source VDD was separated into two equivalent sources to permit

a further separation of the input and output regions of the network.

IG = 0A ,Kirchoff’s current law requires that IR1= IR2 and the series

equivalent circuit appearing to the left of the figure can be used to find the level of VG.

21

DD2G

RR

VRV

SDGGS

RSGSG

RIVV

VVV

0


VG can be found using the voltage divider rule :

Using Kirchoff’s Law on the input loop:

Rearranging and using ID =IS:

Again the Q point needs to be established by

plotting a line that intersects the transfer curve.

Procedures for plotting

1. Plot the line: By plotting two points: VGS = VG, ID =0 and VGS = 0, ID = VG/RS

2. Plot the transfer curve by plotting IDSS, VP and calculated values of ID.

3. Where the line intersects the transfer curve is the Q point for the circuit.

Once the quiescent values of IDQ and VGSQ are determined, the

remaining network analysis can be found.

Output loop:

2121 RR

VII DDRR

)( SDDDDDDS RIRIVV

DDDDD RIVV

SDS RIV

Effect of increasing values of RS

Example Determine IDQ, VGSQ, VD, VS, VDS and VDG.

Example Determine IDQ, VGSQ, VDS, VD and VS

Find VDS and VGS when ID = 5mA

Vs = ID * RS = (5mA)*(470) = 2.35 VVD = VDD – ID * RD

= 15 V – (5mA)(1k) = 15 V – 5 V = 10 VVDS = VD – VS

= 10 V – 2.35 V = 7.65 VVGS = VG – VS = 0 V – 2.35 V = - 2.35 V

Questions

Find VDS and VGS when ID=8mA RD = 860 Ohm RS = 390 Ohm VDD = 12 V

RD = 860 Ohm, RS = 390 Ohm, VDD = 12 V, ID=8mA

Vs = ID * RS = (8mA)*(390) = 3.12 VVD = VDD – ID * RD

= 12 V – (8mA)(860 ) = 12 V – 6.88 V = 5.12 VVDS = VD – VS

= 5.12 V – 3.12 V = 2 VVGS = VG – VS = 0 V – 3.12 V = - 3.12 V

Setting the Q-Point of a Self-Biased JFET To determine ID for a desired value of VGS or

vice versa.

Rs = | VGS/ID |

Midpoint Bias When VGS = VGS(off)/3.4

ID = IDSS/2

using formula below

Graphical Analysis of a Self-Biased JFET Using VGS = -ID*Rs to: 1) Calculate VGS when ID = 0 (VGS,0) 2) Calculate VGS when ID = IDSS (VGS, IDSS) or Get IDSS from data sheet 3) Draw a line between (0,0) and (VGS, IDSS) 4) The line intersects the transfer characteristic

curve is the Q-point of the Circuit

Load Line Calculation 1) Calculate VGS when ID = 0 (VGS,0) VGS = -ID*RS = - 0*470 = 0 (0,0)

2) Calculate VGS when ID = IDSS (VGS, IDSS)

or

Get IDSS from data sheet VGS = -ID*RS = -10mA*470 = -4.7 V (-4.7,10)

3) Draw a line between (0,0) and (-4.7,10m)

4) The line intersects the transfer characteristic curve is the Q-point of the Circuit.

A self Bias dc load line and the Q-point

Determine the Q-point for this figure when

IDSS = 4 mA

1) Calculate VGS when ID = 0 (VGS,0)

VGS = -ID*RS = - 0*680 = 0

2) Calculate VGS when ID = IDSS (VGS, IDSS)

or Get IDSS from data sheet VGS = -ID*RS = - 4 mA* 680

Ohms = -2.72 V 3) Draw a line between

(0,0) and (-2.72 V, 4mA)


IS = ID

VG = (R2/(R1+R2)) * VDD

ID = (VG – VGS)/RS

Exercise

Determine ID and VGS

when VD = 7V, Vdd = 12 V

R1 = 6.8M Ohms R2 = 1M Ohms RD = 3.3 k Ohms RS = 1.8 k Ohms

Answers ID = (VDD – VD)/RD =

(12 V – 7 V)/3.3k = 1.52mA

VS = IDRS = (1.52mA)(1.8K) = 2.74V

VG = (R2/(R1+R2)) VDD

= (1M / 7.8M)12V = 1.54V

Graphical Analysis of JFET with Voltage-Divider Bias For Id = 0

Vs = Id*Rs = (0)*Rs = 0

Vgs = Vg-Vs = Vg – 0V = Vg

For Vgs = 0

Id = (Vg – Vgs)/Rs = Vg/Rs

For Id = 0

Vgs = Vg

For Vgs = 0

Id = Vg/Rs

Exercise #8

In a certain FET circuit, Vgs = 0V, Vdd = 15 V, Idss = 15 mA, and Rd = 470 ohms. If Rd is decrease to 330 ohms, Idss is.

A) 19.5 mA B) 10.5 mA C) 15 mA D) 1 mA

Exercise #8 Answer

In a certain FET circuit, Vgs = 0V, Vdd = 15 V, Idss = 15 mA, and Rd = 470 ohms. If Rd is decrease to 330 ohms, Idss is.

15 mA

Exercise #9

The JFET has Vgs(off) = -4 V.

Figure 8-57

Exercise #10

Determine the value of Rs required for a self-biased JFET to produce a Vgs for -4 V when Id = 5 mA.

JUNCTION FIELD EFFECT TRANSISTOR(JFET). JFET operation can be compared to a water faucet : The...

Documents

Transcript of JUNCTION FIELD EFFECT TRANSISTOR(JFET). JFET operation can be compared to a water faucet : The...