JTC AUTO TOOLS USA UNDERCAR SERIES - · PDF file• Hydraulic ram included for laborsaving....

JTC AUTO TOOLS USA UNDERCAR SERIES

JTC AUTO TOOLS USA 678 – 876 – 3470 2600 NORTHLAKE DR., SUITE F, SUWANEE, GA, 30024

JTC-1014 AXLE NUT SOCKET

• Application: Isuzu model with 4WD.

• Special cylinder design for suiting the

transmission nut.

• Used period: before 2000.

JTC-1016 INNER CV JOINT PULLER

• Fork type tool pulls CV joints with hidden

retaining rings and joints.

• With this tool, the axle assembly is popped out of

trans axle without damage to transmission case

or inside roller bearing.

• Open Rate: 63mm

JTC-1020 HAND OPERATED FLUID EXTRACTOR (10L)

• Capacity: 10L

• By manpower to push create vacuum pressure

for extracting fluid in any space.

• Special patented design for releasing the

pressure.

• Larger base to prevent falling while operating.



JTC-1024 PNEUMATIC OIL & LIQUID DISPENSER

• 6 liters two in one extracts, and pumps

dispenser.

• Specially designed for using on narrow and

difficult to reach spaces.

• Fixing valve and safety cup for automatic

shut-off extract.

• Content:

1.2m PU hose with flexible rubber nozzle.

1m nylon hose.

6sets / 11kgs / 12kgs / 3.6'

JTC-1025 PNEUMATIC BRAKE BLEEDER

• Economical-fast and easy, reduces labor costs.

• Versatile-handles, most standard and ABS brake

systems.

• Clean-collects old brake fluid without spillage.

• Quiet-integrated silencer for a quieter working

environment.

• Silicon suction assembly with universal rubber fitting.

• Capacity: 2L

• Working pressure: 70 - 170psi

• Air connection: 1/4"

• Temperature range: -3˚ F ~ 140˚ F

• 12 sets / 15kgs / 16kgs / 6'

JTC-1026 BRAKE OIL FILLER

• To fill brake oil easily.

• 12 sets / 7kgs / 8kgs / 1.8'



JTC-1032 VACUUM OIL EXTRACTING MACHINE & BRAKE

BLEEDER

• Capacity: 12L

• Uses compressed air to create a powerful

vacuum to extract any kinds of oil,

gasoline, diesel, water, and others

anytime.

• With limpid cup to check the flow anytime.

JTC-1033 HAND OPERATED OIL PUMP

• With reservoir capacity 20L.

• It is suitable for general lubricant and gear oil.

JTC-1034 AIR OPERATED GREASE PUMP

• Uses air as power to stuck grease into

lubrication points.

• Suitable for 00# ~ 2# grease.

• Capacity: 20L

• Air inlet pressure:4 ~ 9kgs/cm

• Pressure ratio: 45:1

• Grease output pressure:180 ~ 405kgs/cm

• Deliver rate: 30cc/sec



JTC-1035 HYDRAULIC GEAR PULLER SET

• For agriculture machine, automotive, and

industry use.

• Hydraulic ram included for laborsaving.

• Material: SCM415 hardened 40˚ ~ 45˚

• Packing: carrying case

• 1 set / 16kgs / 17kgs / 1.2'

JTC-1036 OUTER TIE ROD REMOVER

• Two adjustable jaws special designed for

removing.

• Most models of outer tie rod.

• Material: SCM420 Hardened 42˚

• Packing: each / double blister.

• 6 sets / 24 sets / 29kgs / 30kgs / 2.3'

JTC-1045 HAND OPERATED FLUID EXTRACTOR (6.5L)

• Capacity: 6.5L

• By manpower to push and create

vacuum pressure for extracting fluid in

any space.

• Special patented design for releasing

the pressure.

• With extra tube storage.

• Heat-resistance Temperature: 60℃



JTC-1050 PNEUMATIC & HAND OPERATED FLUID

EXTRACTOR

• Capacity: 10L

• Pneumatic and manual operation fluid extractor of

non-sparkle.

• Three air outlets with check valve design for quick

and easy to exhaust the air from the extractor.

• Easy to operate and suitable for engine oil, gear oil,

brake fluid, water, etc.

• Provided with a modern design decompression

valve for easy to release the negative pressure.

• All parts are the same as JTC-1020.


JTC-1129 PITMAN ARM PULLER

• Heavy duty forged alloy steel yoke.

• Heat treated center screw.

• Remove tie rod ends and pitman assemblies from

many light trucks.

• Opening size: 27mm

• Pull travel: 45mm

JTC-1141 TWO SETS BEARING SEPARATOR KIT

• Bearing separator 9000 and 9005

included.

• Pull out the bearing with the H-type

beam and bolts.



JTC-1143 HYDRAULIC BEARING SEPARATOR PULLER KIT

• Bearing separator 9025 inside.

• Effort-saving with the hydraulic screw.

• Pullout the bearing with the H-type beam

and bolts.

JTC-1145 UNIVERSAL AXLES SLIDE HAMMER SET

• Increased the cover range with the two axle

pullers.

• Includes 3-jaw puller and many types of joints.

• Slide hammer design for removing hub and

repairing dent, etc.

JTC-1146 3–JAW INTERNAL & EXTERNAL PULLER SET

• Size:

Small of internal puller 15mm ~ 30mm

Large of internal puller 30mm ~ 80mm

External puller 15mm ~ 80mm

• Locking the nut to open 3-jaws and

clip the bearing, and then use the slide

hammer to pull out the bearing.



JTC-1212 CLIC–R COLLAR PLIERS

• Distinctive design for the CV ear type

clamps.

• For releasing and refitting reusable hose

clip.

• For type clic and clic-R.

JTC-1217 CV BOOT CLAMP TOOL

• Easy to work in narrow spaces.

• Extra work on nose makes it compact.

• A socket with ratchet is used to turn the

actuating screw for adjustment.

JTC-1230 ANGLE LOCATOR

• Angle adjustable with the magnet

attaching on the align magnet tool

currently working on.

• Applicable with JTC-1840 or JTC-1002.



JTC-1247 BALL JOINT SEPARATOR 19mm

• Applicable on powerful structures.

• Stand design to solve space problems.

• Jaw open: 19mm.


• Jaws open: 23mm

• Jaws deep: 25mm

• Applicable: Audi, BMW, Citroen, Ford, Mercedes,

Opel, Peugeot, Renault, Rover, Saab, Volvo, VW,

Porsche, Pkw, etc.


• Jaws open: 28mm

• Jaws deep: 25mm

• Applicable: Audi, A4, A6, A8, VW,

Passat after 97, etc.



JTC-1259 UNIVERSAL HUB PULLER

• Readily adjustable sliding legs to pull wheel

hubs more quickly and easily where the

bolt circle does not exceed 7-1/2"

(190.2mm)

• Removers press-fit rear brake drums.

• Striking handle and puller screw included.

• Special designed to use on most models of

cars.

JTC-1316 BALL JOINT EXTRACTORS 18mm

• For splitting track rod ends, anti-roll bar

mountings, ball joints, etc.

• A: 18mm

• B: 36mm

• C: 38mm


• For splitting track rod ends, anti-roll

bar mountings, ball joints, etc.

• A: 23mm

• B: 45mm

• C: 47mm






• A: 29mm

• B: 62mm

• C: 62mm

JTC-1319 BALL JOINT EXCTRACTORS 40mm



• A: 40mm

• B: 62mm

• C: 76mm


• For splitting track rod ends, anti-roll


• A: 46mm

• B: 76mm

• C: 100mm



JTC-1323 UNIVERSAL STRUT NUT TOOL SET

• The complete sizes for using on most kinds

of cars.

• Contents:

2 pcs central sockets: 5, 10mm

9 pcs central sockets: 4, 5.2, 6, 6.3, 7, 8, 9, 10, 12mm

4 pcs central sockets 5, 6, 7, 8mm

3 pcs central sockets 3, 3.5, 4mm

2 pcs central sockets T50, T60

1 pcs central sockets M12

4 pcs central sockets 8, 9, 10, 11mm

9 pcs central sockets 14, 16, 17, 18, 19, 21, 22, 24, 27mm

5 pcs central sockets 10.5, 12.5, 14, 14.5, 14.5mm

JTC-1329 CV BOOT HOSE CLAMP CUTTER

• Designed easy to cut the stainless clamp.

• Avoid hurting C.V. Boot.

• Width: Under 10mm

• Thickness: Under 0.5mm ~ 0.7mm

JTC-1335 MANUAL BRAKE GAUGE SET

• Distinctive design to give customers an

accurate measurement of how much

brake lining is left without guess work.

• Size:

Red: 2, 3mm – Bad

Yellow: 4, 5, 6mm – Dangerous

Blue: 8, 10, 12mm – Good



JTC-1336 THIN TYPE BALL JOINT SEPARATOR

• Special design for using on ball joint space

limited.

• The mini operation space: 6 ~ 7mm.

• Jaws open: 22mm

JTC-1365 1/2" PENTAGON SOCKET BIT DRIVER 10mm

• For using on most vehicles fitting with girdling

brake systems.

• Material: CR-V

• Use with 1/2" Drive wrench

JTC-1401 HEAVY DUTY COIL SPRING COMPRESSOR

• Hook engage spring which can be

compressed by turning hex nut.

• Jaws capacity: 23mm ~ 280mm

• Length: 280mm



JTC-1405 DISC BRAKE PISTON COMPRESSOR (4 PISTONS)

• Special wider pusher design to use on 4

pistons vehicle.

• Pusher width: 88mm

• Applicable: BENZ, BMW, and 4 pistons

vehicle.

JTC-1503 CV BOOT CLAMP INSTALLER

• Installs low-profile clamps used to hold CV boots

on most FWD vehicles.

• Ratcheting action and built-in cutter to tighten

the clamp quickly and properly.

JTC-1531 CV BOOT CLAMP PLIERS (EXTENSION)

• For all ear-type clamps.

• Application: For AUDI, BMW,

CHRYSLER, FORD, GM, HONDA,

MAZDA, MERCEDES, NISSAN, OPEL /

VAUXHALL, VW, etc.

• Designed to use with a 1/2" extension

handle or torque wrench.



JTC-1541 14 PCS WHEEL HUB RESURFACING KIT

• To clean impurities in wheel case.

• Contents:

1 - 1/2" grinding slice x 6 pcs

2" grinding slice x 2pcs

Special holder

OPTIONAL PARTS:

JTC-1546 HOSE CLAMP PLIERS (ANGLE TYPE)

• Designed with angle type to any space.

• Swivel tip designed for refitting and release.

• For clic and clic-r type hose clamp.

JTC-1559 HONDA REAR TRAILING ARM BUSH

INSTALLER / REMOVER

• For replacement of the Honda rear

trailing arm bush.

• On car maintenance.

• Hook design to mount the tool on

trailing arm securely.

• No damage to ABS sensor cable,

trailing arm, and parts close to bush

during the maintenance.

• Applicable:

Honda CR-V 1996/9 ~ 2002/8.K6.K8



JTC-1619 INNER CV JOINT PULLER

• Fork type tool pulls CV joints with hidden

retaining rings & joints on 1986 - current

Taurus/Sable.

• With this tool the axle assembly is popped

out of trans-axle without damage to

transmission case or inside roller bearing.

• Open Rate: 48mm

JTC-1628 HUB SLIDE HAMMER PULLER

• Pulls flange-type rear axles on most late model

passenger cars & light trucks.

• Designed to fit axles with bolts & studs up to

9/16" diameter.

JTC-1708 BRAKE SPRING COMPRESSOR

• BIG WINDOW designed for great

visibility during operation.

• Allow fast and easy removal, and

replacement of brake shoe hold-down

springs.



JTC-1709 BRAKE SPRING TOOL

• Hook the brake return spring and screw-up

to lock it for removal and installation.

• A smart tool to service those breaks that

don’t use anchor pins.

JTC-1727 UNIVERSAL BALL JOINT SEPARATOR

• Special design 2-stage operating suits most cars

and light trucks ball joints in steering and

suspension.

• Offset lever permits maximum jaw opening in

30mm and 56mm.

• Jaw open: 22mm.

• Applicable: Europe cars.

JTC-1733 TIRE CONSUMPTION GAUGE

• Determine the average tire residual energy

between both positions which is unconsumed

part, and also is a right barometer for safe

driving.

• To brake below tire thread 1.6mm / will bring

inferior effect.

• Offers measurement of tire thread from 1 ~

30mm.

• For automobile, below 1.6mm thread depth is

recommended for change.

• For truck, below 2.4mm thread depth is

recommended for change.



JTC-1833 CV BOOT CLAMP TOOL

• Work on all CV joint with band-type boot

clamps.

• Provides fast proper installation of those

clamps with ease.

• This small, inexpensive functional tool for

use with 1/4" or 3/8" width band.

JTC-1836 INNER TIE ROD TOOL (8 PCS)

• Works on the inner tie rods with inaccessible wrench flats.

• Many inner tie rod end sockets do not have a complete hex

on the full length of the socket. The rounded socket ends

prevent assess to the wrench flats.

• Seven crows feet, sizes 1-3/16", 1-1/4", 1-5/16", 1-7/16",

14mm, 17mm and 33.6mm, to engage the wrench flats.

• The long socket then slips over the tie rod end and

connects to the crows foot.

JTC-1839 MULTI – PURPOSE INNER TIE ROD TOOL

• The master tie rod tools easily

replaces inner tie rod ends without

removing the rack and pinion.

• Capacity: 33 - 42mm

• Patented.



JTC-1840 ALIGNMENT TOOLS

• With 4 pcs alignment plates.

• Hydraulic function.

• Suit for most car.

JTC-1843 BLIND HOLE BEARING PULLER SET

• Open clamps by turning handle clockwise to snug

against the bearing for pulling out evenly without

damaging the parts.

• Contents:

Shaft: Slide hammer shaft 390mm long

Hammer: 2.15lb. (940g), 100mm L.

Clamps:

8 ~ 10mm (5/16" ~ 13/32"); 10 ~ 12mm (13/32" ~ 15/32")

12 ~ 14mm (15/32" ~ 9/19"); 15 ~ 17mm (9/32" ~ 11/16")

17 ~ 20mm (11/16" ~ 25/32"); 20 ~ 24mm (25/32" ~ 15/16")

25 ~ 29mm (1" ~ 1-1/8"); 30 ~ 32mm (1-3/16" ~ 1-1/4")

JTC-1911 WHEEL WEIGHT TOOL

• Easily removes and replaces wheel

weights, as well as cutting and

crimping.

• Made of heat strengthened steel.

Included comfortable vinyl handle

grips.

• With self-open function spring on the

handle for easier operation.



JTC-1914 UNIVERSAL BALL JOINT PULLER

• Special steel for removing the ball pivots

on steering.

• Jaw open: 17mm

JTC-1915 UNIVERSAL BALL JOINT PULLER

• Special steel for removing the ball pivots on

steering arms, steering tie rocks, steering

knuckles, etc.

• Jaw open: 20mm.


• For splitting track-rod ends, anti-roll


• A: 22mm

• Max. B: 62mm



JTC-1920 CV BOOT CLAMP PLIERS

• For ear type clamp.

• Fits CV joint boots.

• Also installs perma-Quick type clamps

quickly and easily.

• Use for filter, cooling system and vacuum

lines.

JTC-1941 INTERCHANGEABLE – FORK SPRING COMPRESSOR

• Spring compressors are multi-application tools

specifically.

• Developed for modern macpherson suspensions,

using a range of 3 sets of interchangeable

monobloc forks.

JTC-1944 HEADLIGHT ADJUSTING AND BRAKE SPRING

HOOK

• This tool made from heat treated alloy

steel is specially designed for

removing and installing hard-to-reach

headlight adjusting springs. OAL 6".



JTC-1950 STEERING WHEEL PULLER SET

• Two specialty pullers in one set including

one flange type puller for removal of

harmonic balancers, timing gear & other

parts with two or three tapped holes. And

a steering wheel, pulley and flywheel

puller.

JTC-1952 PITMAN ARM PULLER

• Heavy duty forged alloy steel yoke.

• Remove tie rod ends and pitman assemblies from

many light trucks.

• Opening size: 33mm

• Pull travel: 64mm

JTC-3429 RUBBER CEMENT FOR TIRE SEAL

• Constituent: Toluene, Crude Rubber

• Volume: 250CC

• 12 / 72 / 21.5 / 23 / 2.01'



JTC-3430 TIRE SEAL (5 SHEETS / 25 PIECES)

• Constituent: Butyl, Silk Cotton

• Contents: 25 strips of 5 pieces

• 100 / 19.2 / 20.5 / 1.96'

JTC-3431 TIRE SEAL TOOL SET

• Contents: JTC-3922, JTC-3923, JTC-3429, JTC-

3430, Portable tool box.

JTC-3460 ROLLER STITCHER

• Wood handle for light and portable.

• Bearing inside for using easier.

• Spec.: φ38 x 5mm



JTC-3523 VALVE CORE TORQUE TOOL 25Ncm

• Prevents over or under torqueing.

• Serves as both a core remover and installer.

• Prevents premature tire failure due to leaking

valves.

• Easy and simple to use.

• Range of the torque: 25N.cm/2 lbf.in (+-6%)

• Valve type: rubber

• Color: red

JTC-3524 VALVE CORE TORQUE TOOL 45Ncm

• Prevents over or under torqueing.

• Serves as both a core remover and installer.

• Prevents premature tire failure due to leaking valves.

• Easy and simple to use.

• Range of the torque: 45N.cm/4 lbf.in (+-6%)

• Valve type: metal

• Color: black

JTC-3922 METAL T–HANDLE CLOSED EYE TOOL

• Durable metal T-handle design.

• Chrome-Molybdenum steel tip.

• Tip length: 53mm

• Changeable tip design.



JTC-3923 METAL T – HANDLE RASP EYE TOOL

• Durable metal T-handle design.




JTC-3926 SNAP IN TIRE VALVE INSTALLER

• Steel constructed tool deep threaded head for

positive sealing of all snap-in type passenger car

tire valve stems.

• Rubber cover design to protect the rim.

• 3-position settled.

• Patented.

JTC-3932 VALVE CORE REMOVER / INSTALLER TOOL

• For installation and removal of

standard valve cores.

• Has a screwdriver-style handle.

• Tip diameter: 5.5mm




JTC-4039 RATCHET EXHAUST PIPE CUTTER

• This revolutionary tool works like a

standard ratcheting pipe cutter, but can

handle the larger diameter of exhaust

pipes.

• Contents：1 - 1/8 " ~ 2 - 1/2 ", 28 - 67mm,

thickness≦3mm

• Suit for use on exhaust, tailpipes, thin-wall

copper and steel or stainless tubing.

• Instructions:

JTC-4043 FLEXIBLE HOSE CLAMP FOR CLIP–R TYPE

• For replacement of fuel, oil and water hose with

Clip-R hose clamp.

• Hose clamp with flexible 630mm wire.

• Convenient for working hidden areas and long

distance.

JTC-4055 WISHBONE EXTRACTION TOOL

• Designed groove for adjust the position to

work easily.

• To push down the wishbone and other

suspension parts, e.g. during the disassembly

of the drive shaft, during replacing the gaiter

or exchange of the wheel bearing. After

loosening the ball joint, the wishbone must, in

most cases, be pushed down against the bush

or stabilizer tension, to pull the joint from the

support.

• With this lever tool, the work can comfortably

and surely be accomplished by one person.



JTC-4057 2 PCS EXHAUST PIPE REMOVER

• Designed especially for providing pull out

the exhaust pipe easily.

• Special designed two-way for use with

17mm open wrench and 3/8 " Dr. ratchet

wrench to adjust bolt to pull out the pipe.

JTC-4058 LIGHTWEIGHT 3–FUNCTIOON TIRE GAUGE – CLIP TYPE

• 3-function (check, release, inflator) all together

on the press handle.

• Large 80mm gauge with 360° swivel function.

Tube length: 600mm

• Lightweight design for easier operation. Weight:

0.63kgs

• Accuracy: under 110psi: ±3psi; above 110psi: ±4psi

• Capacity: 170psi/12bar (1200kpa)

JTC-4064 EXTRA LARGE C DISC OF JTC-1941

• Extra-large disc 1 pc for BMW E38,

Chrysler, and Renault etc.

• Operation range：180 ~ 240mm

• Only use with JTC-1941.



JTC-4065 EXTRA LARGE ROUND DISC OF JTC-1941

• Special designed large round disc with

protective cover for BMW E39, E40 series.

• Only use with JTC-1941.

JTC-4069 LOCKING RING W/O EYELET PLIERS

• Specially designed for removing and installing

wheel bearing locking rings which without eyelet.

• Applicable：TOYOTA, LEXUS, Citroen

JTC-4091 UNIVERSAL BUSH REMOVE & INSTALL SLEEVE

SET

• Universal application of step discs for

bearing bush, silent bearing, hydraulic

bearing, and rubber bearing on many

kinds of different vehicles.

• 20 pcs sleeves: ID φ34 ~ φ72mm (in 2mm

increment)

• 2 pcs step discs: use with sleeves.

• 4 pcs bolts: M10, M12, M14, M16

• Length: 450mm



JTC-4098 EXTRA LARGE INNER TIE ROD TOOL

• The master tie rod tools easily replace

inner tie rod ends without removing the

rack and pinion.

• Enormous size than JTC-1839

• Capacity: 40 ~ 47mm

JTC-4116 UNIVERSAL JOINT INSTALLER / REMOVER (MID. TRUCK)

• To remove and install universal joint of

transmission shaft.

• Using C clip as a support to remove the joint.

• Applicable:

Middle truck: MITSUBISHI (CANTER), NISSAN,

TOYOTA, MAZDA, ISUZU, etc.

• Patented.

JTC-4126 THIN TYPE LARGE BALL JOINT SEPARATOR

• Special designed to remove the ball

joint in narrow space.

• Mini operation space: 6 ~ 7mm.

• Jaws open: 28mm.

• Applicable: LUXGEN, etc.



JTC-4133 SUZUKI (JIMNY) FRONT WHEEL NUT SOCKET

(4 HOLES)

• Special designed to remove the front

wheel nut with 4 holes.

• Applicable: SUZUKI (JIMNY) 1.3

JTC-4135 ANGLE LOCATOR

• Special designed to for wheel alignment with

adjustable locator.

• Magnet diameter: 77mm

• SIZE: 20(L) x 76(W) x 30(H) mm

JTC-4151 COIL SPRING COMPRESSOR

(WISHBONE SUSPENSION)

• Suitable for lower wishbone diameter

size is smaller than 30mm.

• Provided a 100Nm torque driver.

• Available for using air impact.

• Works well with car working.

• Wide vehicle applications.

• Patented on three-point lock key

design.



JTC-4158 TOYOTA DRIVE AXLE NUT INSTALLER &

REMOVER

• Specially designed to make and

remove the fixing point on the nut of

drive axle.

• 2 pcs in a set. One for making the

fixing point and the other for

removing the fixing point to remove

the nut from drive axle.

• Length: 170mm

• Applicable: TOYOTA, LEXUS

JTC-4164 TOYOTA SUB–FRAME BUSH INSTALLER & REMOVER

• Removal and installation of rear rubber mounts

of axle suspension.

• On car maintenance. Do not need to remove the

sub-frame.

• Applicable: TOYOTA.

JTC-4165 BRAKE CALIPER ADJUSTER

• For rewinding the piston in all collets

type disc brake calipers with

• built-in parking mechanism.

• Essential for fast and easy pad

replacement and caliper servicing.

• Applicable: FORD, HONDA, JAGUAR,

MAZDA, MITSUBISHI, NISSAN, ROVER,

SUBARU, TOYOTA with ABS.



JTC-4190 BALL JOINT SEPARATOR (HIGH)

• To remove the ball joint which is longer

than normal vehicles.

• Jaw open: 28mm

• Jaw deep: 40mm

• Inside height: 74mm

• Applicable: BMW 7 series, BENZ S series,

LEXUS 460, etc.

JTC-4236 LIGHTWEIGHT 3–FUNCTION TIRE GAUGE ACCURATE TYPE

• All the function and weight are the same as JTC-4058.

• Accuracy: between 30 ~ 45psi: ± 1psi, the rest: ±2psi.

• Capacity：87psi / 6bar (600KPa).

• Special designed for high accuracy requesting of tire

pressure checking.

JTC-4252 10L PNEUMATIC ATF & LIQUID DISPENSER

• Use to extract, transfer and dispense fluid quickly,

safely and cleanly.

• Non-spark, one man in same step operate.

• 10L capacity reservoir with volume guide.

• Screw valve to allow easy change extract or dispense.

• Copper material one touch coupler design for easy

operating.

• Air inlet: 1/4"

• Avg. Air Cons: 2 CFM

• Temperature range: -20°C ~ 60°C

• Provide with the safety valve, pre-setting 43 psi (3

Bar), the exceed pressure will be relief automatically.



JTC-4269 BRAKE SPRING WASHER PLIERS

• Universal application for nearly all drum

brakes.

• Special neck angle provides easy removal

and installation of brake spring washer.

• Length: 180.5mm

• Material: steel

• Heat treatment: HRC43° ~ 46°

• Max angle: 50°

JTC-4306 FORD WHEEL HUB BEARIING TOOL SET – 78mm

• Special designed for installing and removing the

wheel hub bearing.

• Operation on car.

• External diameter of bearing fixing discs: φ78mm.

• Applicable:

FORD: Focus, CMAX.

MAZDA: M3.

VOLVO: C30, C70, S40, V50

JTC-4307 FORD WHEEL HUB BEARING TOOL SET – 82mm

• Special designed for installing and

removing the wheel hub bearing.

• Operation on car.

• External diameter of bearing fixing

discs: φ82mm.

• Applicable: FORD, Focus, Mondeo.



JTC-4319 EXHAUST PIPE EXPANDER

• Application range: 40 ~ 64mm.

• Special designed to expend one of the pipe

first While contracting with exhaust pipe

• Applicable: stainless steel.

JTC-4323 BRAKE DISC & TYRE DEPTH GAUGE

• Special device that allows the measurement to be

fixed while measuring the disc thickness in

various locations.

• Brake disc measure range: 0~60mm.

• Measure tyre depth.

• Made of Aluminum.

JTC-4328 PLASTIC HAND OPERATED OIL PUMP

• Tank material: PE; Lid material PP.

• Capacity: 30L

• Deliver rate: 75cc/cycle.



JTC-4454 10 PCS TIRE PRESSURE SENSOR REMOVER /

INSTALLER SET

• Specially designed to remove and install

the TPMS in correct torque.

• Contents:

Fixed Torque 0.45 Nm Tire valve core installer.

Adjustable Torque 1.4, 3.3, and 4 Nm for

assembling TPMS.

TX-bits T10, T15, T20, and 1/4" bit adapter.

Holder thorn 2mm, and hex wrench.

1/4" deep socket 11, and 12mm.

• Applicable: Most brand of TPMS.

JTC-4459 EUROPEAN CAR BALL JOINT REMOVER (4 SIZES)

• Specially designed for quick and easy removing

the ball joint connections.

• Applicable:

BMW E38, E39, E52, E53, E60, E61, E70, E83, E90, E91, E92,

R50, R52, R53, RR1, RR2, X5.

Mercedes W211, W219, W220 and W230.

PORSCHE 996 Carrera.

AUDI A, AUDI A6 lower suspension ball joint.

• Size: 24mm, 27mm, 31mm, 36mm.

JTC-4465 6 BOLT HUB SEPARATOR

• Use for removing the 6 holes HUB rear

axle.

• JTC-4817 is optional for using as an

axle slide hammer.

• Applicable:

TOYOTA HIACE 100 series, 200 series

NISSAN CARAVAN E25 series, E26 series



JTC-4466 FRONT AXLE REMOVAL TOOL SET

• This tool set is required when replacing the

front HUB upper screw, brake disc and

bearing, etc.

• Specially designed for removing each part

on the front HUB.

• Applicable:

TOYOTA HIACE 200 series: 2WD, 4WD

NISSAN CARAVAN E25, E26 series: 2WD, 4WD.

JTC-4468 BRAKE DISC RUN–OUT KIT

• Quickly and easily to check the ball joint abrasion

and brake disc run-out.

• The pliers can enable the dial gauge to use in

various angles against the brake disc.

• This kit includes a Metric calibrated dial gauge.

JTC-4479 JAGUAR AXLE BEARING NUT SOCKET

• Special tool for removing and installing

the axle camber bearing nut which

with ABS rotor on it.

• Size: 3/4" Dr. x 12PT.

• Applicable: JAGUAR XJ8, XK8, etc.



JTC-4482 CITROGEN & PEUGEOT BALL JOINT SOCKET

• Use for removing and installing the screw

nut of the ball joint.

• Use with 35mm/6PT wrench.

• SIZE: Ø51mm/4PT.

• Applicable：Peugeot 405/Citroen.

JTC-4487 TOYOTA REAR HANDBRAKE SPRING DRIVER

• Specially designed tool that can reach deeper to

hold down the spring cup on TOYOTA cars.

• Applicable: TOYOTA Camry, Tacoma, Tundra, FJ

Cruiser, 4Runner, and Land Cruiser since 2000.

JTC-4492 UNIVERSAL HUB BEARING REMOVER /

INSTALLER

• Specially designed to extract and

install the Hubs and singular wheel

bearings of spindle assemblies.

• Designed for FWD, RWD and AWD

vehicles with independent suspension

and a roller ball bearing.

• Applicable:

FWD VW, AUDI and some Asian vehicles.

RWD Mercedes, Porsche, BMW and some

European vehicles.



JTC-4514 BOIL TEST BRAKE FLUID ANALYZER

• True boiling testing base on SAE J1730.

• Straight-stand design, for both nimble and

stabile.

• Less fluid wastage via the content cup

• User friendly, one button to complete the

test

• Durable ceramic core, available for racing

fluid.

JTC-4528 REAR TRAILING ARM BUSH INSTALLER / REMOVER

(FORD, MAZDA, VOLVO)

• Specially designed for easy removal and installation of

the rear arm bush.

• By using this tool can insert the bush to the correct

depth.

• Applicable:

Mazda 3 BK 03 ~ 08, BL 09 ~

PREMACY 05 ~ 10,

AXELA03 ~ 09.

5 CR 05 ~ 10

Ford C-Max 03 - 07

FOCUS I CAK 98 - 05, CB4 08 - 11, II 04 - 08

Kuga CBV 08 ~

Volvo S40 II 04 ~, V50 04 ~

• OEM bush number: 98AG 5K896 AB

JTC-4537 UNIVERSAL SEAL INSTALLER

• The spider arm can be trimmed to fit the

seal, and keep the seal centered during

installation.

• By using the long handle can install the

pinion seals in a flexible way.

• Applicable: 32mm-60mm

• Contents:

Hex cap screw x1

Washerx1

Handle x1

Small spider x1

Large spider x1

Spider insert x1

63mm driver x1

76mm driver x1



JTC-4539 ATF DIFFERENTIAL PRESSURE REFUELING

MACHINE

• Refill or reflux the oil by using the pressure

difference between the two uneven oil

tanks.

• After refueling, lower the oil tank to

withdraw the extra oil.

• Capacity: 4L (Can be refilled during use.)

• Attached with 8pcs adapter set, same as

JTC-4252#D.

JTC-4540 OPEN TYPE STEERING KNUCKLE SPREADER TOOL (SINGLE)

• Adjustable tool designed for spreading the

steering fixed seat of shock absorbers without

damaging the aluminum or cast-iron knuckle.

• Made of chrome-moly steel for more strength.

• Applicable: VAG, BMW, Citroen, FORD, Renault,

Seat, Peugeot and most Japanese vehicles.

JTC-4541 OPEN TYPE STEERING KNUCKLE SPREADER

TOOL (TWIN)

• Adjustable tool designed for spreading

the steering fixed seat of shock

absorbers without damaging the

aluminum or cast-iron knuckle.

• Applicable: Specially designed for twin

ball joints as fitted on VAG control

arms.

• Made of Chrome-moly steel for more

strength.



JTC-4548 HAND OPERATED GREASE PUMP

• Capacity: 20L

• Suitable for 00# ~ 2# grease.

• Deliver rate: 4cc/press

• Hose length: 6ft

JTC-4564 BRAKE SHOE GAUGE

• A time saving tool for measuring the brake pad

lining on the vehicle without removing the wheel.

• Special slim design for measuring the distance

between the lower side of the backing plate and

brake disc.

• Designed for both internal and external brake

pads, features a 1.5mm and calibration check

marking.

• Capable for 6mm backing plate (class IV, V).

JTC-4640 C.V. JOINT BANDING TOOL (WITH CUTTER)

• Operated by hand or 1/2" wrench.

• This tool is easily removed by sliding

sideways after winding has been

completed.



JTC-4641 BEARING PACKER

• To pack grease into bearing by easily

compressing.

• To add grease from the grease fitting in the

top or removing the body.

• Applicable: bearing max. I.D.??16mm and

max O.D.??95mm.


• For splitting track-rod ends, anti-roll bar


• A: 17mm

• MAX. B: 58mm


• For splitting track-rod ends, anti-roll


• A: 32mm

• MAX. B: 80mm




• For splitting track-rod ends, anti-roll bar


• A: 45mm

• MAX. B: 90mm

JTC-4660 2 PCS RUBBER RING HOOK TOOL SET

• Specially designed to pull the rubber ring which

connected with exhaust tube.

• 2 special angle hook attached.

JTC-4661 BALL JOINT SEPARATOR (HIGH)

• Adjustable size for your convenient to

fit different vehicle.

• Jaw opening: 20mm

• Applicable height: 27 ~ 55mm



JTC-4663 EXHAUST SPRING CLAMP REMOVER /

INSTALLER

• Distinctive design to hold opening the

spring clamp and replace the exhaust.

• Total length: 300mm

• Max. jaws opening: 60mm

• Applicable: Peugeot, Renault, Citroen, etc.

JTC-4672 INTERNAL BEARING REMOVER SET

• Two function bearing remover for puller and slide

hammer.

• Contents:

1 pc Tailpipe expanders (62mm).

1 pc Slide hammer.

5 pcs Puller: 8 ~ 11mm, 12 ~ 17mm, 18 ~ 23mm, 24 ~

29mm, 30 ~ 34mm.

3 pcs extension threads.

• Applicable: bearing I.D.: 8 ~ 34mm

JTC-4713 SHOCK ABSORBER RAM DISMANTLE SOCKET

• To insert this tool in and twist 90° to

pull open the sleeve, and remove the

ram.

• Applicable: VW, AUDI, SKODA, SEAT,

FORD, BMW, CITROEN, RENAULT, and

PEUGEOT.



JTC-4725 SLOTTED SOCKET 24mm

• Distinctive design for removing/installing

the steeling fixing nut on the truck.

• Size: 1/2" Dr. 4.0 x 24 mm

JTC-4731 10 POINT IMPACT SOCKET 20mm

• Special designed for the fixing screw on the rear

torque frame of HONDA CR-V.

• Size: 1/2" Dr. x 20 mm 10 points

JTC-4810 TUBE BRAKE OIL FILLER

• Capacity: 1000 c.c.

• To hook by front side and fix the oil

can, the middle side is tube of silicon;

the oil can is steadied by magnetic

hook.

• The gravitation will not be transmitted

to car and causes oil can to break.

• Available for narrow spaces using as

tube designed.



JTC-4817 HUB SLIDE HAMMER PULLER

(OUTSIZE HAMMER)

• Extra-large internal hole for European car.

• Coverage with five oval-shaped holes to

meet assorted sizes of hubs.

• Increasing the power of pulling with both

hands held outsize slide hammer.

• Hammer weight: 6.3kgs

JTC-4829 SINGLE–WAY BRAKE BLEEDER TUBE

• Straightforward way to release the remained

brake oil.

• Adjustable black rubber adapter for distinct size

nozzle.

• With simple screen to show the clear oil and

finish the work.

• Capacity: 1000 c.c.

JTC-4855 EXTRA LARGE CUSTOM–BUILT BUSH /

BEARING / SEAL DRIVER SET

• This extra-large driver set allows you

to build your own custom bushing

driver. Select the required sizes and

assemble your driver tool.

• Discs relate to a shaft and screw which

connects to the driver handle.

• Build to suit the required seal bush or

bearing job.

• Discs size: 70mm through to 150mm in

5mm increments.



JTC-4856 CUSTOM BUILT BUSH / BEARING / SEAL DRIVER

SET

• This master set allows you to build your

own custom bushing driver. Select the

required sizes and assemble your driver

tool.

• Build to suit the required seal, bush or

bearing job.

• Disc size: G18mm through to 65mm in

1mm increments and 74mm.

JTC-4868 EXHAUST PIPE HANGER STRETCHER

• The stretcher removes exhaust rubber-style

hangers easily.

• The slip-resistant handles and self-locking force

pin allow for quick removal of rubber exhaust

hangers.

• A slim profile and 25° offset allow for easy access

to confined areas.

JTC-4873 HUB PULLER & SEPARATOR

• Fix the plate on the tire screw thread,

screw the bolt to separate the wheel drive

shaft and hub by pushing.

• Pick the fit output shaft adapter to meet

central screw, then lock in the

transmission shaft, put the frame on, lock

the nut and fix the screw to pull the wheel

shell close to the drive shaft.

• Output shaft adaptor: M22 x 1.5, M24 x

1.5, M27 x 1.5, M30 x 1.5



JTC-4880 BRAKE CALLIPER GUIDANCE THREAD REPAIR

SET

• For repairing the guide pen threads in the wheel

bearing housing.

• With disassembly of guide ping while changing the

brake pads the internal threads are frequently

destroyed.

• The defective threads are repaired professionally

and quickly with a heavy-duty rust-proof high-grade

steel threaded bush.

• Contents:

Replacement bushes with copper ring M9 X 1.25 (packing

unit 10 pcs).

Special core drill.

Special tap M9 X 1.25.

Hex key 7mm.

• Applicable: FORD, OPEL, VW, AUDI.

JTC-5341 3–JAW INTERNAL BEARING REMOVER SET

• Use for removing the internal bearing, sleeve,

and disc.

• Range: 13 ~ 38mm

JTC-5611 TIRE PRESSURE GAUGE

• Calibrated in 0.2 kgs/cm2 (20kPa)

increments from 1 to 11kg/cm2(100 ~

1100kPa) and 2.5 lb./in2 from 10 to

160 lb./in2.

• Chrome-plated and 270mm long.

• Head I.D. is 8mm.



JTC-5807 EFFORT–SAVING CLOSED EYE TOOL

• Hook the identity to let the ribbon through

the tire, then to make the needle's way

forward by hand push.

• Good effort-saving by hook tire to make

the needle's way forward.

• The needle way is smooth-going, easy to

orientate, will not cause over or less.

JTC-1001A 25 PCS FWD FRONT WHEEL BEARING TOOL

(WITH BEARING)

• A great tool used to replace front wheel bearing

without removing the steering knuckle and strut

assembly.

• As the spindle assemble isn`t removed, there is

no need to align front end after the job is done.

• Fits on most cars.

• Applicable with hydraulic press.

• Total: 25 pcs brand new combination.

JTC-1023A PNEUMATIC FLUID EXTRACTOR

• Capacity: 8.5 liter

• Work pressure: 90 psi

• Simple and easy to operate suitable for

engine oil, gear oil, transmission and

brake fluid water.

• Extract with 3 min for 5-liter engine oil.

• Non-spark power oil extractor

• Only operate by one man, clear operation.

Save manpower.

• Quick and safe.


• 4 sets / 9kgs / 10kgs / 3.8'



JTC-1142A BEARING SEPARATOR KIT

• Bearing separator 9015 Included.

• Pullout the bearing with the H-type beam

and bolts.

JTC-1142P EXTRA LONG EXTENTION BAR FOR JTC-1142

• To use with JTC-1142.

• For removing the bearing between rear drive

shaft and differential.

• Length：640 mm

JTC-1404A SPRING COMPRESSOR STAND

• Rotate the steering disc to make it move up-down for quick

operation and labor-saving. Besides, it won't leak oil like hydraulic

type.

• Special designed upper jaws to adjust up-down and front-back

direction for fixing the spring tightly, safely, and stable.

• The compressor fixed base could hold the cylinder center very

easily and it's very convenient to dismantle.

• The lower supporting stand could prevent the shock absorber

from moving downside to make the cylinder to be deformed.

• Specially designed for dismantling shock absorber, applicable for

most cars.

• Patented.

1. Rotate gear wheel of the steering disc to drive

the upper jaws in an up-down direction.

2. The fixing hook was installed inside carrier shim

and the jaw could be adjusted in up-down and

front-back to be at appropriate position for

pressing the spring safely.

3. Fix cylinder in center position as the lower

stand will support and prevent the cylinder

from being deformed.

4. Adjust up-down direction to support the shock

absorber for easier operation.



JTC-1452A 21 PCS POSITIVE & NEGATIVE CALIPER WIND

BACK KIT

• More adapters than 1613A for using on

more new model vehicles.

• Two bodies with positive thread and

negative thread for different models.

• Total: 21 pcs.

JTC-1532A CV BOOT CLAMP PLIERS (HEAVY DUTY)

• For assembly of new stainless-steel clamp-bands

on drive-shafts where a torque setting is

required.

• The 3/8" torque wrench is ideal to provide the

drive.

• Made from CR-MO material, which is rigid and

durable.

JTC-1538A POCKET BRAKE FLUID TESTER

• The tester can be a digital brake fluid

tester suitable for determining brake

fluid quality.

• Quality is tested and indicated on five

LEDs in terms of “per cent of water in

the brake fluid”.

• LED display: Green: no water – OK.

Yellow: less than 1% of water. – Warming.

Yellow/yellow: approx. 2% of water. – Warming.

Yellow/yellow/red: approx. 3% of water. The oil

should be changed.

Yellow/yellow/red/red: At least 4% of water.

Change the oil urgently.



JTC-1610A FWD FRONT WHEEL BEARING TOOL

• A great tool used to replace front wheel

bearing without removing the steering

knuckle and strut assembly.

• As the spindle assemble isn't removed

there is no need to align front end after

the job is done.

JTC-1613A 15 PCS CALIPER WIND BACK KIT

• Winds back brake piston for replacing brake

pads.

• Fits most cars.

JTC-1943A STEERING WHEEL REMOVER / LOCK PLATE

COMPRESSOR SET

• Removing steering wheels of most

vehicles with or without telescoping

tilt steering columns is easy with this

new set.

• The steering wheel lock plate

compressor is also included, to

compress the steering wheel lock

plate to remove or install the snap

ring.



JTC-3922L METAL T HANDLE CLOSED EYE TOOL

• Durable metal T handle design.




JTC-4144A HAND OPERATED ATF FLUID DISPENSER

• Tank capacity: 9.5 liter

• Flow capacity: 75 cc/cycle

• Hose size: 3/8" x 1500mm.

• Size: 330x 260x 650mm.

• Special designed for filling ATF oil.

• Replaceable fittings for different vehicles.

• With hand pump for vacuum to prevent oil deterioration.

• Weight: 3.5kg

• Contains 8 fittings.

JTC-4219A WHEEL STUD ALIGNMENT GUIDE TOOL

• Assists when mounting wheels,

especially late models with long lug

bolts.

• Applicable: all Mercedes models with

lug bolts.

• Size:

2 - M12 x 1.25

2 - M12 x 1.5

2 - M14 x 1.25

2 - M14 x 1.5



JTC-4920S HUB SLIDE HAMMER SET

• With 4 holes and 5 holes for all the

vehicles.

• Increasing the power of pulling with both

hands held outsize slide hammer.

• Hammer weight：6.3 kgs

JTC-F0412 BALL JOINT SEPARATOR 24mm

• Tempered drop forged steel one-piece

construction for long & rough usage.

• 15/16" (24mm) Fork, 11-7/8" (300mm) length

replace worn out ball joint easily with a hammer

striking.

• Can remove CV drive shafts on FWD vehicles.

JTC-F0416 THIN BALL JOINT SEPARATOR 18mm

• Tempered drop forged steel one-piece

construction for long & rough usage.

• 21/32" (18mm) Fork, 16"(410mm)

length replace worn out tie rods easily

with a hammer striking.

• Can separate shock absorber links.



JTC-F1954 BALL JOINT SEPARATOR

• Heat treated drop forged steel body & bolt

for long rough usage.

• Spread ball joints easily where space

prevents use of direct method.

• Jaw open: 19mm.

JTC-F270 DROP FORGED COIL SPRING COMPRESSOR

• Drop forged CR-V steel jaws and leaded screws

(270mm) both heat treated ensure you obtain

professional job performance.

• The tool is designed for use in limited space

under wheel arch.

• Jaw design is fitting to warp coil claws for safely.

• Maximum jaw opening is 270mm.

JTC-F370 DROP FORGED COIL SPRING COMPRESSOR

• Heat treated drop forged CR-V steel

jaws & leaded screws (270mm)

• The tool is designed for use in limited

space under wheel arch.

• Distinct design claws to warp on coil

spring safely.

• Maximum jaw opening is 270mm.



JTC-J01 DISC BRAKE PISTON SEPARATOR

• Fits in brake caliper to push back pistons

for new brake pads installation.

• Patented.

JTC AUTO TOOLS USA UNDERCAR SERIES - · PDF file• Hydraulic ram included for laborsaving....

Documents

Transcript of JTC AUTO TOOLS USA UNDERCAR SERIES - · PDF file• Hydraulic ram included for laborsaving....