jPM Series Worm Gear Units · Boom,luffing (2) Rotating,swingorslew (3) Tracking,drivewheels (4)...

Superior Gear Technology

jPM Series Worm Gear Units

jPM Series - Product Features

www.renold.com

Unique Holroyd tooth form formaximum torque capacity andoptimum efficiency.

One piece outputsleeve with electronbeam weldedbronze worm wheelrim ensuremaximum strengthunder shock loadconditions.

Section of electron beam welded wormwheel rim and centre showing the fusion of thebronze wormwheel rim onto the cast iron centre.This high security fit allows transmission of power under shock load conditions.

Machined surfaces on all sides of gearcase, plus detachable feet and B5output flange for wide range ofmounting options.

Accepts standard B5 and B14motors via plug-in polymer bush

for durability, quietnessand strength.

Heavy duty ball &taper roller bearingscombining maximumload with long life.

2

Contents

www.renold.com

3

Page No

jPM Unit Features 2

ATEX Approval Details 4

General Specifications 5

Product Options 6

Mounting Positions 7

Unit Designation Code 8

Selection Data - Geared Motor Units 9

Selection Data - Speed Reducers 10

Load Classification by Application 11

Drive Classification 12

Overhung & Thrust Loads 13

Installation and Maintenance 14

Selection Data - Geared Motor Units 15 - 18

Dimensions - Single Reduction Units 19 - 35

Dimensions - Torque Restraints 36

Selection Data - Speed Reducer Units 37 - 48

ATEX Approval Details

www.renold.com

4

ATEX ApprovalGears products for operating in potentially explosive

atmospheres.

General� Gears units are classified as ATEX Group II Category

2 equipment, which embodies sufficient safeguards to besuitable for use in potentially explosive atmospheres for normaloperation and for operation during an expected malfunction.

� It is essential that there is sufficient lubricant to prevent thegears and bearings running ‘dry’. Gear units should beinspected daily for signs of oil leakage, overheating or noisyoperation.

� Gear units should be cleaned at regular intervals depending onthe operating conditions, to ensure that dust coatings neverexceed 5mm. Plastic parts should be wiped clean with a dampcloth.

� Oil leaks should be dealt with as quickly as practical. Compoundjoint faces and shims should be cleaned and thread-lockingsealant should be applied to bolts and plugs prior to re-assembly.

� The temperature of any external surfaces must not exceed thepermitted maximum of 135°C (T4).

� Higher temperature class T3 is available dependant on unitmounting, ratio and gear type. For further details consultRenold.

� As a general rule, gear units should be mounted with their feethorizontal. For other mountings, particularly with shaftmounted units, consult Gears.

WARNING: IF MOUNTING WITH VERTICAL INPUT OR OUTPUTSHAFTS, THE ATEX CERTIFICATION DOES NOT APPLY.

Unit Selection� The gear unit selection procedures must include an additional

reliability factor of 1.25 for mechanical ratings and 1.25 forthermal ratings.

ATEX Nameplate

GEARCASEThe close-grained cast iron gearcaseis of one-piece construction tomaximize strength and rigidity and toreduce load bearing joints.The internal case style is designed forefficient circulation of lubricant withsuch a beneficial effect on thermalproperties that no cooling fan isnecessary. The gearcase contoursare smooth and clean to minimize theaccumulation of dirt and to facilitatecleaning.The case is drilled and tapped onthree faces to accommodate the boltsfor the feet or torque arm bracket.Normally the unit will be delivered withthe unused holes blocked with plasticplugs which can be easily removed ifrequired.

GEARSThe worm is integral with its shaft, andmanufactured from alloy steel, casehardened on the threads and groundand polished on the thread profiles.The wormwheel rim is produced fromphosphor bronze complying with BS1400 PB2-C (centrifugally cast) andsecured to the steel output sleeve bythe electron beam welding process.The Holroyd gear form used in this

range of gearboxes corresponds toBritish Standard recommendationsand, in addition, has an exclusivefeature which consists principally of animportant modification to the wormthread and wheel tooth which confersadditional valuable properties to gearperformance. This ensures that ourgears will run correctly and transmittrue uniform angular velocity evenwhen running under non-uniform loadconditions. The modification alsogives a tapered oil entry gap betweenthe teeth, which drags the lubricantbetween the surfaces and results inoil-borne friction only.

SHAFTSThe shaft extensions and sleeve boresare to metric dimensions andincorporate standard rectangularparallel keyways which conform to BS4235: Part 1: 1972 and DIN 6885recommendations.Where an output shaft extension isrequired rather than a bored sleeve,this can be supplied from stock andsimply "plugged in" and secured with acirclip. The overhung and thrust loadswhich these shafts will sustain areshown on page 13. Solid constructionoutput shafts are also available.

BEARINGSStandard metric bearings to ISOstandards are fitted throughout thejPM range of units.

LUBRICATIONAll jPM units are factory-filled with asynthetic lubricant, giving theadvantages of low coefficient offriction, extended temperature rangeand long life. Each unit receives ametered amount suitable for everymounting position shown on page 15.The gears and bearings are positivelylubricated by oil from the sump. Incertain applications having inputspeeds below 500 rpm a largeramount of lubricant may be required:in order that this requirement can beidentified and met, details of theapplication and mounting positionshould be supplied to Renold Gears.

WEIGHTSThe weights listed below cover thegear units in shaft-mounted form andfilled with lubricant.

*JPM11 2.9JPM17 8.0 15.8 21.4 24.4 25.4JPM22 14.5 22.3 27.9 30.9 31.9 41.5 48.6JPM26 20.7 28.5 34.1 37.1 38.1 47.7 54.8JPM30 26.9 34.7 40.3 43.3 44.3 53.9 61.0

UnitRef.

Weight (kg) Single Reduction Unit

*JPM11 geared motor with D63 motor= 6.9kg *JPM11 geared motor with D71 motor= 8.3kg

Geared Motors

D71 D80 D90S D90L D100L D112MSpeedReducer

JPM17 11.6 19.4 25.0 27.8 29.0JPM22 18.1 25.9 31.5 34.5 35.5 45.1JPM26 24.3 32.1 37.7 40.7 41.7 51.3JPM30 30.5 38.2 43.9 46.9 47.9 57.5

UnitRef.

Weight (kg) Helical Worm Unit

Geared Motors

D71 D80 D90S D90L D100LSpeedReducer

General Specification

www.renold.com

5

SPEED REDUCERThis version covers the basic gear unitwith the wormshaft having a keyedextension, as shown on page 20.

MOTOR GEAR UNITA motor adaptor is assembled onto theinput side of the unit to the frame sizespecified.In this form the wormshaft has securedto it a coupling having a bored recessand an axial slot. A keyed plastic bushis fitted to the motor shaft on assemblyand as the two are brought togetherthe tongue on the bush is located inthe axial drive slot.Units can be supplied complete withmotor or with the adaptor fitted andcomplete with motor shaft bush to suitour customer's own IEC motor.

FOOT MOUNTING - TYPE 2This foot arrangement comprises asingle component, dimensional detailsof which are shown on pages 22 and23. It can be secured to the gearcasein any of three positions by foursocket head screws, the position offoot location being denoted 2.0, 2.1and 2.2 as shown on page 7.

OUTPUT ADAPTORThe circular adaptors which can beattached to the output sides of thegearcase agree to IEC D patterndimensions and located in a recessmachined in the case or wheel capand secured by socket head screws.They can be fitted to either side.

FOOT MOUNTING - TYPE 4These feet are manufactured fromsteel and are secured by bolts to theholes in the gearcase in the requiredposition; see pages 26 and 27 fordimensional details.

OUTPUT SHAFTWhere an output shaft extension isrequired, suitable single or doubleextension plug-in shafts are available.They can be inserted in the bore,located by the key and secured axiallyby a circlip. Both the key and circlipare supplied with the shaft.When assembling the shaft into thesleeve it is advised that an anti-fretting compound be applied. RocolASP anti-scuffing paste is a suitablematerial for this purpose.

TORQUE RESTRAINTWhen used in the shaft mountingposition the unit can be restrainedfrom rotation by attaching to the sideof the driven machine by the outputflange or by the adjustable torque armarrangement shown on page 36.Other torque restraint types can besupplied depending on customerspreference.

ADDITIONAL SUPPLYAny of the above options can besupplied separately or fitted prior todespatch from our works if specifiedon the order. The various positionsand handings of assembly are shownon page 7.

HELICAL WORMA helical first stage reduction isavailable covering unit sizes 17 to 30,offering ratios from 5:1 to 280:1. Theunit is available as a speed reducer ormotorised type up to 4 kW capacity.This type of unit has advantages ofhigher efficiencies and can allow downsizing of unit selections. Further detailsare available from the Renold Gearssales office.

Solid output shafts are also available in single and double extension to the same dimensions as the plug-in shafts.

HELICAL WORM jPM UNIT

Options Available

www.renold.com

6

Each unit is filled on assembly with ametered amount of lubricant which issufficient for each of the mountingpositions shown, with the exception ofsome situations where the inputspeed is below 500 rpm.The code numbers indicate the typeof foot or flange arrangement relativeto the position of the input.

Since the units are sealed they can beplaced in any of the positionsillustrated without further modification.If a plug-in output shaft is required,and this is to be fitted on supply, thehanding arrangement must bespecified as indicated.

1.0 2.0 2.1 2.2

3.0

3.1

4.0 4.1

HANDINGS

RIGHT-R DOUBLE-DLEFT-L

The diagrams above illustrate therelative directions of rotation of theinput and output shafts. All jPM gearunits are reversible.

Mounting Positions

www.renold.com

7

1. TypejPM

2. SizeFive models: 11, 17, 22, 26, 30

3. InputM - Motorised unit with motor

suppliedA - Motorised unit without motor

but with motor adaptorH - Non-motorised unit with input

shaft extension

4. Motor FrameSeven Frame sizes:63, 71, 80, 90S, 90L, 100, 112

5. MountingEight Mounting types: see page 7.

6. HandingIf the unit is to be assembled ontothe driven shaft, coding is S. If anoutput shaft extension is requiredthere are three shaft handingpositions: see page 7.Use the letter relative to the shaftand handing required.

7. Ratio12 Standard ratios: 5, 7.5, 10, 12.5,15, 20, 25, 30, 40, 50, 60, 70.

8. Special FeaturesT - Torque arm assemblyB - Braked motor. Give details of

stop/start frequency, stoppingtorque on enquiry/order.

SS - Slow Speed input, i.e. inputspeed below 500 rpm.

TR - Torque restraint bracket.

POWER AND TORQUE RATINGSThe power and torque ratingspublished assume a uniform loadcondition at the speeds stated underambient temperature conditionsbetween minus 10°C and plus 30°C .If the temperature is likely to exceed30°C, consult Renold.

SERVICE FACTORSTable 1 (page 11) lists a range ofapplications with an assessment of thenature of the loading; this is thenclassified as Steady, MediumImpulsive, or Highly Impulsive.The information obtained here can thenbe applied to table 5 (page 12) forgeared motor units, or table 2 (page11) for reduction gear units, where thehours of operation are also taken intoaccount and the Duty Service Factor fDobtained.The Drive Classification, table 5,facilitates selection of geared motorunit where the gear unit/motorcombination is already resolved relativeto the duty factor and a straightforwardselection can be obtained from thecapacities on pages 15 to 18.If the number of stops and startsexceeds five each hour a ServiceFactor fS must be applied (see table 3page 4; also NOTE above).

Example:Selection Power=output kW to drivenmachine fD.fS.f T

NOTEWhen the duty involves frequentstop/start cycles it may be necessaryto check the capacity of the motor forthe application. In this situation theinertia of the driven machine will haveto be considered.

EXAMPLE:

Type

Size

Input

MotorFrame

Special Feature

Ratio

Handing

Mounting

jPM 22 M 71 2.2 L 30 SS

Unit Designation Code

www.renold.com

8

EXAMPLE 1A jPM shaft-mounted geared motorunit is required to drive a rotarypump at 200 rpm, eight hours perday, and the power requirement is1.7 kW.1. Output power is 1.7 kW at 200

rpm given.2. Rotary pump rated as uniform

loading in table 1 and for eighthours per day continuousoperation drive requirement isClass 1 in table 5.

3. Reference to nominal powerhigher than 1.7 kW i.e. 2.2 kW ,Drive Classification 1 on page 15shows that a jPM 22 is availablewith an output speed of 192 rpm.This is close enough for theduty. The power capacity of theunit is 1.97 kW.

4. The ratio of 7.5/1 can be found inthe second column, motor framesize from the table on page 8,and so the coding for theselected unit is:

Type - jPMSize - 22Input - MMotor Frame - 100Mounting - 1.0Handing - SRatio - 7.5Special Features - None

Which reads: jPM22 M 100 1.0 S 7.5

EXAMPLE 2A geared motor unit is required todrive a uniformly loaded bottleconveyor operating for 24 hourseach day. The torque required atthe output shaft is 200 Nm at 35rpm. The output shaft projectsvertically upwards and is fitted witha 12" pitch circle diameterchainwheel, the unit being mountedon a horizontal surface.

1. Output speed 35 rpm.2. Power absorbed by driven

machine= 200 x 359550

= 0.73 kW3. Drive classification from table 5 is

2, i.e. uniform load operating inexcess of 10 hours per day.

4. Selection table for DriveClassification 2 on page 16 listsnearest output speed of 35 rpmas 36 rpm where we find againsttorque requirement 200 Nm asize jPM 30 complete with a 1.1kW motor is rated at 225 Nm.

5. Overhung load= 9.55 x 0.73 x 106 x 1

6 x 25.4 x 36= 1270 N

From the chart on page 13 we findthat a jPM 30 with an output speed50 - 25 rpm will support a radialload of 6900N.

The coding for the jPM unit is:Type - jPMSize - 30Input - MMotor Frame - 90 i.e. 1.1 kWMounting - 3.1Handing - LRatio - 40 i.e. 1410 40

36

Special Features - None

Which reads: jPM30 M 90 3.1 L 40.

Confirm that the supply to the motoris 415 volt +/- 5%, 3 phase, 50 Hz.

GEARED MOTOR UNITSThe capacities covering the jPMgeared motor units are on pages 15 to18 where it will be seen that thesehave already been classified inaccordance with the duty requirementsbased upon the nature of loading andoperational hours each day.The units are listed under the nominalmotor power against output speed,with the selection output power andtorque included in the block with therespective gear unit size. Variations inefficiency with regard to ratio aretherefore taken into account.The output speeds listed areapproximate only, being based uponthe nominal gear ratio and a motorspeed of 1440 rpm. The actual gearratios can be found in the capacitycharts.To select a jPM geared motor unit theprocedure below should be followed:-

1. Determine the output speed.2. Determine the power absorbed by

the driven machine:

Absorbed Power (kW) =Absorbed Torque (Nm) x Machine Speed (rev/min)

95503. Determine the load classification

from table 5 (page 12) and, usingthe information obtained togetherwith the number of operating hourseach day, derive the DriveClassification from table 5(page 12).

4. Select unit from the tables onpages 15 to 18 by class andensure output power/torque isequal to or in excess ofpower/torque absorbed by drivenmachinery.

5. If unit is subjected to imposedexternal thrust or overhung loadscheck the details against thecapacities listed on page 13 toconfirm such loads are within thecapability of the unit.

6. Note working conditions: clean,dusty, moist, abnormaltemperatures etc.

OVERLOADSThe overload carrying capacity of alljPM units is equivalent to that of thecage-type motors specified for usewith them.

Selection of JPM Units Geared Motor Units

www.renold.com

9

EXAMPLE 3A jPM gear unit is required to drive amachine which is in operation for 24hours per day under moderate shockload conditions with 20 stop/startcycles per hour. The input speed is1410 rpm with an output powerrequirement of 0.8 kW at 55 rpm.The unit is foot mounted with theinput shaft horizontal above theoutput. An output shaft is requiredprojecting to the right when viewedat the input end.

1. Input speed 1410 rpm, outputspeed 55 rpm and output power0.8 kW given.

2. Ratio - 1410 = 25.655

Nearest standard is 25/1.

3. The drive classification servicefactor for 24 hours per dayoperation under moderate shockload conditions is 1.5 from table2. The factor for 20 stop/startcycles per hour from table 3 is1.1.

The selection power is 0.8 x 1.5x 1.1 = 1.32 kW.

4. From the capacities listed for25/1 ratio on page 43 we find thatat 1500 rpm a jPM 26 has anoutput power capacity of 1.48kW.

The coding therefore is:Type - jPMSize - 26Input - HMounting - 2.2Handing - LRatio - 25

The code for the above is thenjPM 26 H 2.2 L 25.

5. To find the input power requiredestablish the efficiency which= 1.38 x 1001.61

= 85.7%

Input power = 0.8 x 100 = 0.93 kW85.7

GEAR UNITSTo select a jPM speed reducer unitthe following basic information mustbe known.

1. The power absorbed by the drivenmachine.

2. Input and output speeds.

3. Characteristics of the drive, e.g.degree of impulsiveness of drivenload. See application table onpage 11.

4. Duration of service in hoursper day.

5. Frequency of stop/start cyclesper hour.

6. Disposition and details of externalthrust loads or overhung load whenthe output shaft is fitted.

7. Working conditions: clean, dusty,moist, abnormal temperatures etc.

If the operating conditions are in anyway unusual it is advisable to consultour Sales Technical Staff.

From this basic information is derivedthe gear ratio and selection power tobe applied to the Selection Tables.

Gear Ratio = Input Speed (rpm)Output Speed (rpm)

The capacities given in pages 37 to 48are based upon 10 hours per daycontinuous running with steady,uniform load conditions.If the load is not steady, or theoperational hours per day differ fromthe nominal rated period, then theactual power is multiplied by a ServiceFactor to obtain the selection power,and this new figure is then used todetermine, from the Selection Tables,the size of unit required.

i.e. Selection power = Actual power xService Factor (s).

Selection of JPM Speed Reducers Units

www.renold.com

10

S = SteadyM = Medium ImpulsiveH = Highly Impulsive* = Refer to Renold Gears(1) = Select on 24 hours per day

service factor only.(2) = Use service factor of 1.00 for any

duration of service.(3) = Use service factor of 1.25 for any

duration of service.(4) = Use service factor of 1.50 for any

duration of service.

NOTEMachinery characteristics and servicefactors listed in this catalogue are aguide only. Some applications (e.g.constant power) may require specialconsiderations. Consult Renold Gears.

Driven machinery characterisiticsPrime mover Duration Steady Medium Highly(Drive input) Service load impulsive impulsive

AgitatorsPure liquids SLiquids and solids MLiquids-variable density M

BlowersCentrifugal SLobe MVane S

Brewing and DistillingBottling machinery SBrew kettles-continuous duty SCookers-continuous duty SMash tubs-continuous duty SScale hopper-frequent starts M

Can filling machines SCane knives (1) MCar dumpers HCar pullers MClarifiers SClassifiers MClay working machineryBrick press HBriquette machine HClay working machinery MPug mill M

CompressorsCentrifugal SLobe MReciprocating - multi-cylinder MReciprocating - single cylinder H

Conveyors - uniformly loaded or fedApron SAssembly SBelt SBucket SChain SFlight SOven SScrew S

Conveyors - heavy dutynot uniformly fedApron MAssembly MBelt MBucket MChain MFlight MLive roll *Oven MReciprocating HScrew MShaker H

Crane Drives - not dry dockMain hoists SBridge travel *Trolley travel *

CrushersOre HStone HSugar (1) M

DredgesCable reels MConveyors MCutter head drives HJig drives HManoeuvring winches MPumps MScreen drive HStackers MUtility winches M

Dry dock cranesMain hoist (2)Auxiliary hoist (2)Boom, luffing (2)Rotating, swing or slew (3)Tracking, drive wheels (4)

ElevatorsBucket - uniform load SBucket - heavy load MBucket - continuous SCentrifugal discharge SEscalators SFreight MGravity discharge SMan lifts *Passenger *

Extruders (plastic)Film SSheet SCoating SRods STubing SBlow moulders MPre-plasticiers M

FansCentrifugal SCooling towersInduced draft *

Forced draft *Induced draft MLarge, mine etc. MLarge, industrial MLight, small diameter S

FeedersApron MBelt MDisc SReciprocating HScrew M

Food industryBeef slicer MCereal cooker SDough mixer MMeat grinder M

Generators - not welding SHammer mills HHoistsHeavy duty HMedium duty MSkip hoist M

LaundryWashers - reversing MTumblers M

Line shaftsDriving processing equipment MLight SOther line shafts S

Lumber industryBarkers, hydraulic, mechanical MBurner conveyor MChain saw and drag saw HChain transfer HCraneway transfer HDe-barking drum HEdger feed MGang feed MGreen chain MLive rolls HLog deck HLog haul-incline HLog haul-well type HLog turning device HMain log conveyor HOff bearing rolls MPlaner feed chains MPlaner floor chains MPlaner tilting hoist MRe-sawmerry-go-round conveyor MRoll cases HSlab conveyor HSmall waste conveyor-belt SSmall waste conveyor-chain MSorting table MTipple hoist conveyor MTipple hoist drive MTransfer conveyors MTransfer rolls MTray drive MTrimmer feed MWaste conveyor M

Machine toolsBending roll MPunch press-gear driven HNotching press-belt drive *Plate planners HTapping machine HOther machine toolsMain drives MAuxiliary drives S

Metal millsDrawn bench carriageand main drive MPinch, dryer and scrubberrolls, reversing *Slitters MTable conveyors non-reversing group drives MIndividual drives HReversing *Wire drawing and flatteningmachine MWire winding machine M

Mills, rotary typeBall (1) MCement kilns (1) MDryers and coolers (1) MKilns other than cement MPebble (1) MRod, plain & wedge bar (1) MTumbling barrels H

MixersConcrete mixers continuous MConcrete mixers intermittent MConstant density SVariable density M

Oil industryChillers MOil well pumping *Paraffin filter press M

Rotary kilns MPaper millsAgitators (mixers) MBarker-auxiliaries hydraulic MBarker-mechanical HBarking drum HBeater and pulper MBleacher SCalenders MCalenders-super HConverting machine exceptcutters, platers MConveyors SCouch MCutters, platers HCylinders MDryers MFell stretcher MFell whipper HJordans MLog haul HPresses MPulp machine reel MStock chest MSuction roll MWashers and thickeners MWinders M

Printing presses *PullersBarge haul H

PumpsCentrifugal SProportioning MReciprocatingsingle acting:3 or more cylinders Mdouble acting:2 or more cylinders Msingle acting: 1 or 2 cylinders *double acting: single cylinder *

Rotary - gear type SRotary - lobe, vane S

Rubber and plastics industriesCrackers (1) HLaboratory equipment MMixed mills (1) HRefiners (1) MRubber calenders (1) MRubber mill, 2 on line (1) MRubber mill, 3 on line (1) SSheeter (1) MTyre building machines *Tyre and tube press openers *Tubers and strainers (1) MWarming mills (1) M

Sand muller MScreensAir washing SRotary, stone or gravel MTravelling water intake S

Sewage disposal equipmentBar screens SChemical feeders SCollectors SDewatering screws MScum breakers MSlow or rapid mixers MThickeners MVacuum filters M

Slab pushers MSteering gear *Stokers SSugar industryCane knives (1) MCrushers (1) MMills (1) M

Textile industryBatchers MCalenders MCards MDry cans MDryers MDyeing machinery MLooms MMangles MNappers MPads MRange drives *Slashers MSoapers MSpinners MTenter frames MWashers MWinders MWindlass *

TABLE 1

hours/dayintermittent -3hrs/day max

3 - 10over 10

intermittent -3hrs/day max

3 - 10over 10

intermittent -3hrs/day max

3 - 10over 10

Electric, Air &Hydraulic Motorsor Steam Turbine(Steady input)

Multi-cylinder I.C.engine (Mediumimpulsive input)

Single-cylinderI.C. engine(Highly impulsiveinput)

0.901.001.25

1.001.251.50

1.251.501.75

1.001.251.50

1.251.501.75

1.501.752.00

1.501.752.00

1.752.002.25

2.002.252.50

Maximum number 5 50 100 300of starts per hour

Starts Factor fS 1.0 1.1 1.15 1.2

SERVICE FACTORSTABLE 2 (SERVICE FACTOR fD)

TABLE 3 FACTOR FOR STARTS/HOURS (fS)

Units to ATEX approval mustbe selected with a minimum

service factor of 1.25.

IMPORTANT

Load Classification By Application

www.renold.com

11

TABLE 5: TABLE OF DRIVE CLASSIFICATION-GEARED MOTOR UNITS

Steady 1 1 2

Medium implusive 1 2 3

Highly implusive 2 3 4

Driven machinery Duration of servicecharacteristics

Under 3 to 10 Over 103 hours hours hours

Units to ATEX approval mustbe selected with a minimumdrive classification of 2

IMPORTANT

Drive Classifications

www.renold.com

12

300 900 1250 1700 2000 3000 6000 4000 8000 6000 9000200 950 1400 1750 2500 3200 7000 4200 9000 6200 10000150 1000 1650 1800 3000 3400 8000 4400 10000 6400 11000125 1050 1900 1850 3500 3600 9000 4600 11000 6600 12000100 1100 2200 1900 4000 3800 10000 4700 12000 6700 1300075 1200 2500 1950 5000 4000 11000 4800 13000 6800 1400050 1300 2800 2000 6000 4000 12000 4900 14000 6900 1500025 1350 3200 2050 7000 4000 13000 5000 14000 7000 1500015 1350 3800 2050 8000 4000 13000 5000 14000 7000 1500010 1350 4400 2050 9000 4000 13000 5000 14000 7000 150005 1350 4800 2050 10000 4000 13000 5000 14000 7000 15000

jPM11OUTPUTRPM

jPM17 jPM22 jPM26 jPM30

OHL AXIAL OHL AXIAL OHL AXIAL OHL AXIAL OHL AXIAL

A

Output shafts of worm gear units arefrequently fitted with a spur pinion,chain pinion or belt pulley, causing anoverhung load to be imposed on theoutput shaft and bearings. Theseloads can generally be sustained bythe gear unit; however, if the load isgreater than the maximum allowableload for the unit, it may be necessaryeither to select a larger unit or tolessen the effect of the load on theshaft bearings. This can be done intwo ways; the pinion can be mountedon a shaft in its own bearings and theshaft coupled to the gear unit; or thewheel shaft may be extended beyondthe overhung load and fitted with anoutboard bearing. In order to obtainthe best possible arrangement for aparticular application (where largeroverhung loads are anticipated)customers are advised to submitdetails of the load to our SalesTechnical Staff for their consideration.

In the interests of good design, theoverhung member should be fitted asclose as possible to the gear case inorder to minimise the stresses andreduce the deflecting moment on theunit.

The maximum imposed axial thrustand overhung loads (OHL) to whichthe units can be subjected are givenin the table below.

Imposed axial thrust loads can also beminimised by the use of flexiblecouplings on the input and outputshafts.

For drives where both imposed thrustand overhung loads are encountered,it is advisable to consult our SalesTechnical Staff.

Where a double extension shaft isfitted, the maximum overhung loadslisted apply in full to each shaftextension.

The overhung load may be calculatedby the following formula:

resultant overhung load =

9.55 x P x 106 x F (Newtons)R x S

Where P = Power absorbed at outputshaft (kW)

S = Speed of output shaftin rev/min

R = Pitch circle radius of chainpinion, spur or helical gear,or belt pulley in mm

F = Overhung drive applicationfactor as follows:

Chain pinion 1.00Spur or helical gear 1.25Vee pulley 1.50Flat belt pulley 2.00

The overhung load capacities listed inthe table below assume the load isapplied mid-way along the outputshaft extension, the relevantdimension from the centre line of theunit being as given in the diagram.

jPM OVERHUNG LOAD CAPACTIES (N)

Unit Dim A (mm)

JPM11 60JPM17 75JPM22 95JPM26 115JPM30 140

Overhung and Thrust Loads

www.renold.com

13

INSTALLATIONComplete instructions on the correctinstallation and maintenance of jPMunits are sent with each unit suppliedand additional copies are available onrequest.

COUPLINGS AND BEDPLATESAll couplings should be accuratelyfitted and shafts accurately aligned.To prevent damage to the bearings,coupling half-bodies should not behammered onto shafts.Where the plug-in single extensionoutput shaft is fitted the coupling canbe assembled onto the shaft prior tosecuring in the output sleeve.Gear units and other drivecomponents should be rigidly mountedon firm foundations to preventmovement and vibration which mayaffect the alignment of the shafts.Suitable bedplates can be supplied ifrequired.

INITIAL RUNNINGFirst FillingPrior to despatch from our works thegearboxes are filled with the correctamount of synthetic lubricant. This issufficient for all the mounting positionsshown on page 7.

STARTING UPAll worm gear units have beensubjected to a short test beforedespatch to the customer, but it takesmany hours running under full load forthe gear to attain its highest efficiency.The gear may if necessary be put towork immediately on full load, but ifcircumstances permit it is better for theultimate life of the gears to run undergradually increasing load, attaining thefull load after about 20 to 40 hours.Reasonable precautions should,however, be taken to avoid overloadsin the early stages of running.Temperature rise on the initial run willbe higher than that eventually attainedafter the gear is fully run-in.

STORAGEAll worm gear units stored or leftinactive for long periods should beadequately protected, particularlythose on exposed sites and/oroperating in corrosive or saltyatmospheres. Units left inactive forlong periods should, ideally, be run atfull speed for not less than 10 minutesonce each month.

Before a gear unit is returned toservice after a long period of inactivity,oil seals should be checked and, ifnecessary, replaced.

SPARE PARTSInformation relating to spare parts isavailable on request.

BREATHER / VENTING PLUGSTwo holes for plugs are machined intoeach jPM unit as shown in Fig 1,2 and 3.Solid taper plugs are factory fitted intothe holes as a breather plug is notnormally required.However, if because of continuoushigher speed running or high ambienttemperatures a breather is required, oneis supplied with each unit for customersto fit.

BREATHER PLUG

BREATHER PLUG

FIG 1

BREATHER PLUG

FIG 2

FIG 3

Installation and Maintenance

www.renold.com

14

NominalOutputSpeed

revs/min

Nominalgearratio

Motor Power-kW

0.12 0.18 0.25 0.37 0.55 0.75 1.1 1.5 2.2 3.0

SizeOutput

288 5 power kW 0.11 0.17 0.24 0.35 0.53 0.72 1.06 1.39 2.02 2.74 3.65torque Nm 3.8 5.7 7.9 11.6 17.5 24 35 46 67 91 121SizeOutput

192 7.5 power kW 0.10 0.16 0.22 0.33 0.48 0.66 0.99 1.25 1.97 2.69 3.62torque Nm 5.2 7.9 10.9 16.2 24 33 49 62 98 134 180SizeOutput

144 10 power kW 0.10 0.16 0.22 0.32 0.48 0.66 0.97 1.34 1.95 2.68 3.59torque Nm 6.8 10.3 14.3 21 32 44 64 89 129 178 238SizeOutput

115 12.5 power kW 0.10 0.16 0.22 0.29 0.48 0.67 0.90 1.34 1.87 2.66 3.60torque Nm 8.6 12.9 17.9 24 40 56 75 111 155 221 299SizeOutput

96 15 power kW 0.11 0.16 0.22 0.33 0.49 0.67 0.94 1.29 2.03 2.77 3.55torque Nm 10.5 15.7 22 33 49 67 94 128 202 276 353SizeOutput

72 20 power kW 0.10 0.15 0.22 0.32 0.48 0.59 0.93 1.20 1.76 2.46torque Nm 13.5 20 29 43 64 78 124 159 234 326SizeOutput

57 25 power kW 0.09 0.14 0.20 0.29 0.44 0.61 0.87 1.24 1.67 2.32torque Nm 15.4 23 33 49 73 103 146 208 280 388SizeOutput

48 30 power kW 0.09 0.14 0.20 0.29 0.43 0.61 0.89 1.23 1.8torque Nm 17.9 27 39 58 86 121 177 244 358SizeOutput

36 40 power kW 0.08 0.13 0.18 0.28 0.42 0.58 0.86 1.16torque Nm 22 35 49 73 112 153 227 307SizeOutput

28 50 power kW 0.06 0.12 0.17 0.26 0.39 0.54 0.81torque Nm 22 42 59 90 134 185 275SizeOutput


20 70 power kW 0.03 0.13 0.16 0.24 0.36 0.50torque Nm 16.6 53 77 114 174 239

Actual output speeds depend upon the full load speed of the motor and the exact gear ratio, and may differ from the nominal speeds listed.

4.0

JPM11 JPM11 JPM11 JPM11 JPM17 JPM17 JPM17 JPM17 JPM22 JPM22 JPM22





JPM11 JPM11 JPM17 JPM17 JPM17 JPM17 JPM22 JPM22 JPM26 JPM30


JPM11 JPM11 JPM17 JPM17 JPM17 JPM22 JPM22 JPM26 JPM30

JPM11 JPM17 JPM17 JPM17 JPM22 JPM22 JPM26 JPM30

JPM11 JPM17 JPM17 JPM22 JPM22 JPM26 JPM30


JPM11 JPM17 JPM22 JPM22 JPM26 JPM30

:1

Units to ATEX approval must be selected with aminimum drive classification of 2

IMPORTANT

Geared Motor Units - Drive Classification

www.renold.com

15

Motor Power-kW

0.12 0.18 0.25 0.37 0.55 0.75 1.1 1.5 2.2 3.0

SizeOutput



144 10 power kW 0.10 0.16 0.22 0.32 0.48 0.66 0.98 1.33 1.96 2.70torque Nm 6.8 10.3 14.3 21 32 44 65 88 130 179SizeOutput

115 12.5 power kW 0.10 0.16 0.22 0.33 0.48 0.66 0.99 1.34 1.97 2.70torque Nm 8.6 12.9 17.9 27 40 55 82 111 164 224SizeOutput

96 15 power kW 0.11 0.16 0.22 0.33 0.49 0.67 0.94 1.29 2.03 2.77torque Nm 10.5 15.7 22 33 49 67 94 128 202 276SizeOutput






24 60 power kW 0.08 0.12 0.17 0.26 0.39 0.55torque Nm 32 48 69 102 155 217SizeOutput

20 70 power kW 0.08 0.12 0.16 0.25 0.37torque Nm 36 55 77 117 175

4.0












JPM17 JPM22 JPM22 JPM26 JPM30

NominalOutputSpeed

revs/min

Nominalgearratio

:1


IMPORTANT

Geared Motor Units-Drive Classification 2

www.renold.com

16

Motor Power-kW

0.12 0.18 0.25 0.37 0.55 0.75 1.1 1.5 2.2 3.0

SizeOutput



144 10 power kW 0.10 0.16 0.22 0.32 0.48 0.66 0.98 1.33 1.96 2.70torque Nm 6.8 10.3 14.3 21 32 44 65 88 130 179SizeOutput


96 15 power kW 0.11 0.16 0.22 0.33 0.49 0.64 0.94 1.39 2.03torque Nm 10.5 15.7 22 33 49 64 94 138 202SizeOutput

72 20 power kW 0.10 0.16 0.22 0.32 0.47 0.63 0.98 1.35torque Nm 13.5 21 29 43 62 84 130 179SizeOutput





24 60 power kW 0.08 0.12 0.17 0.26 0.40torque Nm 32 48 69 104 159SizeOutput

20 70 power kW 0.08 0.12 0.16 0.25 0.37torque Nm 36 55 77 117 175


4.0













NominalOutputSpeed

revs/min

Nominalgearratio

:1


IMPORTANT

Geared Motor Units - Drive Classification 3

www.renold.com

17

Motor Power-kW

0.12 0.18 0.25 0.37 0.55 0.75 1.1 1.5 2.2 3.0

SizeOutput



144 10 power kW 0.10 0.16 0.21 0.33 0.48 0.66 0.98 1.34 1.98torque Nm 6.8 10.3 14.0 22 32 44 65 89 131SizeOutput

115 12.5 power kW 0.10 0.16 0.22 0.33 0.48 0.67 0.99 1.35 1.97torque Nm 8.6 12.9 18.0 27 40 56 82 112 164SizeOutput

96 15 power kW 0.11 0.16 0.22 0.33 0.47 0.64 0.99 1.39torque Nm 10.5 16.0 22 33 47 64 98 138SizeOutput



48 30 power kW 0.10 0.14 0.20 0.30 0.44 0.58 0.90torque Nm 19.0 28 39 59 88 115 179SizeOutput




20 70 power kW 0.08 0.12 0.17 0.25torque Nm 37 55 79 118


4.0












JPM22 JPM22 JPM26 JPM30

NominalOutputSpeed

revs/min

Nominalgearratio

:1


IMPORTANT

Geared Motor Units-Drive Classification 4

www.renold.com

18

C1

79 276 140 105 106

S4S3S2S1

G1

22.5 45 M6x11 78 37 22.5 45 37 72 37

VUJ3XJ2H2G2J1QK1H1 W

16.01616.034

18.418.3

5.0154.985

B

55 26.43 52 42 42

EDCB1

J3 J1

G1H1

W

U

V

G1H1

B1B

D

E C S1

H1

G1

S3

K1DIA XDEPTH

C1

S4

S2 G2H2

Q

J1

J2

X

jPM11 Geared Motor Unit - Dimensions (mm)

www.renold.com

19

12.008 9.5 3.98811.997 9.4 3.95816.009 13.0 4.98815.996 12.9 4.95819.009 15.5 5.98818.996 15.4 5.95824.009 20.0 7.98523.996 19.8 7.94924.009 20.0 7.98523.996 19.8 7.949

JPM11 28.57 55 26.43 52 42 42 78 22.5 45 37 M6x11 22.5 45JPM17 44.45 85 40.55 78 60 67 98 45.5 69.5 43 M10x17 24 69.5JPM22 57.15 105 47.85 90 80 90 126 57.5 115 45 M10x17 33 90.5JPM26 66.67 117 50.33 97 92 102 140 43.5 87 72 M12x20 43.5 87JPM30 76.2 135 58.8 105 100 120 156 51 102 85 M12x22 51 102

A B B1 C D E Q G1 H1 J1 K1 G2 H2UnitRef.

JPM11 37 37 84 30 25 2.5 72JPM17 57 57 120 40 36 2 92JPM22 55 45 132 40 36 2 118JPM26 72 72 149 50 40 5 132JPM30 85 85 157 50 40 5 148

J2 J3 T1 U1 V1 W1 X1 Y1 Z1 U V W XUnitRef.

16.016 18.4 5.01516.034 18.3 4.98524.020 27.5 8.01824.041 27.3 7.98230.020 33.5 8.01830.041 33.3 7.98238.025 41.5 10.01838.050 41.3 9.98245.025 49.0 14.02145.050 48.8 13.979

SHAFT MOUNTING

W1

V1

U1

X1

Y1 Z1

W

U

V

T1CE

H1G1

D

B

G1

H1

A

B1

K1DIA. xDEPTH

J3

G1

H1

J1

QJ1

H2G2

J2X

HOLLOW WHEELSHAFT DETAIL

INPUT SHAFTDETAIL

jPM Speed Reducers - Dimensions (mm)

www.renold.com

20

G1 H1 K1 Q J1 G2 H2 J2 X J3 U V WUnitRef.

JPM11JPM17 85 40.55 78 60 67JPM22 105 47.85 90 80 90JPM26 117 50.33 97 92 102JPM30 135 58.8 105 100 120

B B1 C D EUnitRef.

JPM17JPM22JPM26JPM30

DIM D71M D80M D90S D90L D100L D112MUnitRef.

24.020 27.5 8.01824.041 27.3 7.98230.020 33.5 8.01830.041 33.3 7.98238.025 41.5 10.01838.050 41.3 9.98245.025 49.0 14.02145.050 48.8 13.979

E C S1

H1

G1

C1

D

B

G1

H1

J3 J1

G1

H1

W

U

V

S2 S3

S4

Q

J1

G2H2

J2

X

B1

K1DIA. xDEPTH


JPM11JPM17 45.5 69.5 M10x17 98 43 24 69.5 57 92 57JPM22 57.5 115 M10x17 126 45 33 90.5 55 118 45JPM26 43.5 87 M12x20 140 72 43.5 87 72 132 72JPM30 51 102 M12x22 156 85 51 102 85 148 85

SEE PAGE 19

SHAFT MOUNTING

C1 34 44 44 44 54 54S1* 231 269 277 302 344 377S2* 140 157 180 180 200 211S3* D Flange 160 200 200 200 250 250S3* C Face 105 120 140 140 160 160S4* 106 113 120 120 136 146

SEE PAGE 19

*jPM11 MOTOR DIMENSIONS SEE PAGE 27

jPM Geared Motors - Dimensions (mm)

www.renold.com

21

A B B1 C D E Q DO DU DV F G HUnitRef.

JPM11 84 30 25 2.5JPM17 120 40 36 2JPM22 132 40 36 2JPM26 149 50 40 5JPM30 157 50 40 5

T1 U1 V1 W1 X1 Y1 Z1UnitRef.

FOOT MOUNTING-TYPE 2

DV

C

H

G

D

B

GH

W

U

V

E

T1

DO

DU

F

L


INPUT SHAFTDETAIL

X1V1

W1 U1

Y1 Z1 J

R

G

H

X

Q

A

B1

K

JPM11 28.57 55 26.43 52 42 42 78 50 63 50 8 35 70JPM17 44.45 85 40.55 78 60 67 98 73 98 80 13 47.5 95JPM22 57.15 105 47.85 90 80 90 126 95 120 105 15 57.5 115JPM26 66.67 117 50.33 97 92 102 140 110 135 120 18 72.5 145JPM30 76.2 135 58.8 105 100 120 156 120 155 140 20 80 160

12.008 9.5 3.98811.997 9.4 3.95816.009 13.0 4.98815.996 12.9 4.95819.009 15.5 5.98818.996 15.4 5.95824.009 20.0 7.98523.996 19.8 7.94924.009 20.0 7.98523.996 19.8 7.949

JPM11 75 7 84 89 72JPM17 95 12 128 125 92JPM22 100 12 160 135 118JPM26 115 14.5 184 150 132JPM30 130 14.5 195 165 148

J K L R U V W XUnitRef.

16.016 18.4 5.01516.034 18.3 4.98524.020 27.5 8.01824.041 27.3 7.98230.020 33.5 8.01830.041 33.3 7.98238.025 41.5 10.01838.050 41.3 9.98245.025 49.0 14.02145.050 48.8 13.979


www.renold.com

22

B B1 C D E Q DO DU DV F G H JUnitRef.

K L R U V W XUnitRef.


DV

C

H

G

B

D

GH

E

DU

DO

F

LK

B1

S2 S3

S1

C1

H

G

X

Q

JR

S4

W

U

V


JPM11 55 26.43 52 42 42 78 50 63 50 8 35 70 75JPM17 85 40.55 78 60 67 98 73 98 80 13 47.5 95 95JPM22 105 47.85 90 80 90 126 95 120 105 15 57.5 115 100JPM26 117 50.33 97 92 102 140 110 135 120 18 72.5 145 115JPM30 135 58.8 105 100 120 156 120 155 140 20 80 160 130

16.016 18.4 5.01516.034 18.3 4.98524.020 27.5 8.01824.041 27.3 7.98230.020 33.5 8.01830.041 33.3 7.98238.025 41.5 10.01838.050 41.3 9.98245.025 49.0 14.02145.050 48.8 13.979

JPM11 7 84 89 72JPM17 12 128 125 92JPM22 12 160 135 118JPM26 14.5 184 150 132JPM30 14.5 195 165 148






www.renold.com

23

JPM11 28.57 55 26.43 52 42 42 78 3 7 10.0 115 60JPM17 44.45 85 40.55 78 60 67 98 3.5 11 10.0 130 85JPM22 57.15 105 47.85 90 80 90 126 3.5 12 12.0 165 105JPM26 66.67 117 50.33 97 92 102 140 4 12 14.5 215 105JPM30 76.2 135 58.8 105 100 120 156 4 12 14.5 215 130

A B B1 C D E Q D1 D2 K2 M N OUnitRef.

JPM11 140 84 30 25 2.5 72JPM17 160 120 40 36 2 92JPM22 200 132 40 36 2 118JPM26 250 149 50 40 5 132JPM30 250 157 50 40 5 148

P T1 U1 V1 W1 X1 Y1 Z1 U V W XUnitRef.

95.00094.946110.000109.946130.000129.937180.000179.937180.000179.937

FLANGE MOUNTING-HOLLOW OUTPUT SHAFT

W

U

V

HOLLOW WHEELSHAFT DETAIL INPUT SHAFT

DETAIL

X1V1

W1 U1

Y1 Z1

E C

T1

A

B1

D

B

Q

X D1

N P

D2O

4 HOLESK2 DIAM PCD

12.008 9.5 3.98811.997 9.4 3.95816.009 13.0 4.98815.996 12.9 4.95819.009 15.5 5.98818.996 15.4 5.95824.009 20.0 7.98523.996 19.8 7.94924.009 20.0 7.98523.996 19.8 7.949

16.016 18.4 5.01516.034 18.3 4.98524.020 27.5 8.01824.041 27.3 7.98230.020 33.5 8.01830.041 33.3 7.98238.025 41.5 10.01838.050 41.3 9.98245.025 49.0 14.02145.050 48.8 13.979


www.renold.com

24

B B1 C D E Q D1 D2 K2 M N O PUnitRef.

FLANGE MOUNTING-HOLLOW OUTPUT SHAFT

W

U

V


E C S1

D

B

Q

X D1

N P

D2

O

S4

S2 S3

C14 HOLESK2 DIAM PCD

B1


U V W XUnitRef.

95.00094.946110.000109.946130.000129.937180.000179.937180.000179.937

JPM11 55 26.43 52 42 42 78 3 7 10.0 115 60 140JPM17 85 40.55 78 60 67 98 3.5 11 10.0 130 85 160JPM22 105 47.85 90 80 90 126 3.5 12 12.0 165 105 200JPM26 117 50.33 97 92 102 140 4 12 14.5 215 105 250JPM30 135 58.80 105 100 120 156 4 12 14.5 215 130 250

16.016 18.4 5.01516.034 18.3 4.98524.020 27.5 8.01824.041 27.3 7.98230.020 33.5 8.01830.041 33.3 7.98238.025 41.5 10.01838.050 41.3 9.98245.025 49.0 14.02145.050 48.0 13.979






www.renold.com

25

H3 L3 R3 T1 U1 V1 W1 X1 Y1UnitRef.

W1

V1

U1

X1

Y1 Z1

W

U

V

T1

CE

H

G

D

B

G

H

A

B1

K

Q

XHOLLOW WHEELSHAFT DETAIL

INPUT SHAFTDETAIL

L1

G3

H3L3

F2

R3


U V W XUnitRef.

JPM11 133 157 41 84 30 25 2.5JPM17 193 225 51 120 40 36 2JPM22 245 285 65 132 40 36 2JPM26 269 309 72 149 50 40 5JPM30 305 355 80 157 50 40 5

A B B1 C D E Q F2 G H L1 K G3UnitRef.

JPM11 28.57 55 26.43 52 42 42 78 3 35 70 84 7 60JPM17 44.45 85 40.55 78 60 67 98 5 47.5 95 130 12 84JPM22 57.15 105 47.85 90 80 90 126 6 57.5 115 160 12 110JPM26 66.67 117 50.33 97 92 102 140 6 72.5 145 190 14.5 122JPM30 76.2 135 58.8 105 100 120 156 6 80 160 200 14.5 135

16.016 18.4 5.01516.034 18.3 4.98524.020 27.5 8.01824.041 27.3 7.98230.020 33.5 8.01830.041 33.3 7.98238.025 41.5 10.01838.050 41.3 9.98245.025 49.0 14.02145.050 48.8 13.979

12.008 9.5 3.98811.997 9.4 3.95816.009 13.0 4.98815.996 12.9 4.95819.009 15.5 5.98818.996 15.4 5.95824.009 20.0 7.98523.996 19.8 7.94924.009 20.0 7.98523.996 19.8 7.949

Z1



www.renold.com

26

B B1 C D E Q F2 G H L1 K G3UnitRef.

H3 L3 R3 U V W XUnitRef.

E C S1

H

G

C1

D

B

G1

H1

B1

W

U

V

S2 S3

S4

Q

X

G3

H3L3

F2

R3L1

HOLLOW WHEEL SHAFT DETAIL

JPM11 55 26.43 52 42 42 78 3 35 70 84 7 60JPM17 85 40.55 78 60 67 98 5 47.5 95 130 12 84JPM22 105 47.85 90 80 90 126 6 57.5 115 160 12 110JPM26 117 50.33 97 92 102 140 6 72.5 145 190 14.5 122JPM30 135 58.8 105 100 120 156 6 80 160 200 14.5 135

JPM11 133 157 41 72JPM17 193 225 51 92JPM22 245 285 65 118JPM26 269 309 72 132JPM30 305 355 80 148


16.016 18.4 5.01516.034 18.3 4.98524.020 27.5 8.01824.041 27.3 7.98230.020 33.5 8.01830.041 33.3 7.98238.025 41.5 10.01838.050 41.3 9.98245.025 49.0 14.02145.050 48.8 13.979






www.renold.com

27

T1CE

H1G1

D

B

G1

H1

A

B1

K1DIA. xDEPTH

J3

G1

H1

J1

QJ1

H2

G2

J2

T2 T2

W2

V2

U2

X2

Y2Z2

W1

V1

U1

X1

Y1 Z1

INPUT SHAFTDETAIL

PLUG IN WHEELSHAFT DETAIL

UnitRef.

JPM11 28.57 55 26.43 52 42 42 22.5 45 37 37 M6x11 84JPM17 44.45 85 40.55 78 60 67 45.5 69.5 43 57 M10x17 120JPM22 57.15 105 47.85 90 80 90 57.5 115 45 45 M10x17 132JPM26 66.67 117 50.33 97 92 102 43.5 87 72 72 M12x20 149JPM30 76.2 135 58.8 105 100 120 51 102 85 85 M12x22 157

T1K1J3J1H1G1EDCB1BA

UnitRef.

JPM11 22.5 45 37 78 80JPM17 24 69.5 57 98 100JPM22 33 90.5 55 126 125JPM26 43.5 87 72 140 155JPM30 51 102 85 156 195

T2QJ2H2G2

UnitRef.

JPM11 30 25 2.5 40 36 2JPM17 40 36 2 50 45 3JPM22 40 36 2 60 50 5JPM26 50 40 5 80 70 5JPM30 50 40 5 110 100 5

Y2X2W2V2U2Z1Y1X1W1V1U1

9.59.413.012.915.515.420.019.820.019.8

3.9883.9584.9884.9585.9885.9587.9857.9497.9857.949

16.00815.99722.00921.99628.00927.99632.01832.00240.01840.002

13.012.918.518.424.023.827.026.835.034.8

4.9884.9585.9885.9587.9857.9499.9859.94911.98211.939

Z2

12.00811.99716.00815.99719.00918.99624.00923.99624.00923.996

PLUG-IN AND SOLID OUTPUT SHAFTS AVAILABLE


www.renold.com

28

K1 U2 V2 W2 X2 Y2 Z2 G2 H2 J1 J2 Q T2UnitRef.

B B1 C D E G1 H1 J3UnitRef.

E C S1

H1G1 C1

D

B

G1

H1

B1

J3 J1

G1

H1

S2 S3

S4QJ1

G2H2

J2

T2 T2

W2

V2

U2

X2

Y2Z2


K1DIA XDEPTH

JPM11 M6x11 40 36 2 22.5 45 37 37 78 80JPM17 M10x17 50 45 3 24 69.5 43 57 98 100JPM22 M10x17 60 50 5 33 90.5 45 55 126 125JPM26 M12x20 80 70 5 43.5 87 72 72 140 155JPM30 M12x22 110 100 5 51 102 85 85 156 195

JPM11 55 26.43 52 42 42 22.5 45 37JPM17 85 40.55 78 60 67 45.5 69.5 57JPM22 105 47.85 90 80 90 57.5 115 45JPM26 117 50.33 97 92 102 43.5 87 72JPM30 135 58.8 105 100 120 51 102 85

16.008 13.0 4.98815.997 12.9 4.95822.009 18.5 5.98821.996 18.4 5.95828.009 24.0 7.98527.996 23.8 7.94932.018 27.0 9.98532.002 26.8 9.94940.018 35.0 11.98240.002 34.8 11.939







www.renold.com

29

J K L R T1 U1 V1 W1 X1UnitRef.

DV

C

H

G

D

B

GH

E

T1

DO

DU

F

L

INPUT SHAFTDETAIL

X1V1

W1 U1

Y1 Z1

JR

G

H

Q

A

B1

K

T2 T2

W2

V2

U2

X2

Y2Z2


JPM11 75 7 84 89 84 30 25 2.5JPM17 95 12 128 125 120 40 36 2JPM22 100 12 160 135 132 40 36 2JPM26 115 14.5 184 150 149 50 40 5JPM30 130 14.5 195 165 157 50 40 5

A B B1 C D E Q DO DU DV F G HUnitRef.

JPM11 28.57 55 26.43 52 42 42 78 50 63 50 8 35 70JPM17 44.45 85 40.55 78 60 67 98 73 98 80 13 47.5 95JPM22 57.15 105 47.85 90 80 90 126 95 120 105 15 57.5 115JPM26 66.67 117 50.33 97 92 102 140 110 135 120 18 72.5 145JPM30 76.2 135 58.8 105 100 120 156 120 155 140 20 80 160

12.008 9.5 3.98811.997 9.4 3.95816.009 13.0 4.98815.996 12.9 4.95819.009 15.5 5.98818.996 15.4 5.95824.009 20.0 7.98523.996 19.8 7.94924.009 20.0 7.98523.996 19.8 7.949

Y1 Z1




16.008 13.0 4.98815.997 12.9 4.95822.009 18.5 5.98821.996 18.4 5.95828.009 24.0 7.98527.996 23.8 7.94932.018 27.0 9.98532.002 26.8 9.94940.018 35.0 11.98240.002 34.8 11.939



www.renold.com

30

B B1 C D E Q DO DU DV F G H JUnitRef.

W2

V2

U2

X2

Y2Z2


F

D

B

DO

DU

S1CE

H

G

DV

G

H

L

K

S2 S3

T2 T2

S4

Q

H

R

J

G

B1

C1


K L R T2 U2 V2 W2 X2 Y2 Z2UnitRef.JPM11 7 84 89 80 40 36 2JPM17 12 128 125 100 50 45 3JPM22 12 160 135 125 60 50 5JPM26 14.5 184 150 155 80 70 5JPM30 14.5 195 165 195 110 100 5

JPM11 55 26.43 52 42 42 78 50 63 50 8 35 70 75JPM17 85 40.55 78 60 67 98 73 98 80 13 47.5 95 95JPM22 105 47.85 90 80 90 126 95 120 105 15 57.5 115 100JPM26 117 50.33 97 92 102 140 110 135 120 18 72.5 145 115JPM30 135 58.8 105 100 120 156 120 155 140 20 80 160 130

16.008 13.0 4.98815.997 12.9 4.95822.009 18.5 5.98821.996 18.4 5.95828.009 24.0 7.98527.996 23.8 7.94932.018 27.0 9.98532.002 26.8 9.94940.018 35.0 11.98240.002 34.8 11.949







www.renold.com

31

A B B1 C D E Q D1 D2 K2 M N OUnitRef.

W2

V2

U2

X2

Y2Z2

T1CE

D

BA

B1

T3

Q D1

PN

D2O

W1

V1

U1

X1

Y1 Z1


4 HOLESK2 DIAM PCD

INPUT SHAFTDETAIL

T2

FLANGE MOUNTING

P T1 U1 V1 W1 X1 Y1 Z1UnitRef.

JPM11 140 84 30 25 2.5JPM17 160 120 40 36 2JPM22 200 132 40 36 2JPM26 250 149 50 40 5JPM30 250 157 50 40 5

JPM11 28.57 55 26.43 52 42 42 78 3 7 10.0 115 60JPM17 44.45 85 40.55 78 60 67 98 3.5 11 10.0 130 85JPM22 57.15 105 47.85 90 80 90 126 3.5 12 12.0 165 105JPM26 66.67 117 50.33 97 92 102 140 4 12 14.5 215 105JPM30 76.2 135 58.8 105 100 120 156 4 12 14.5 215 130

95.00094.946110.000109.946130.000129.937180.000179.937180.000179.937

12.008 9.5 3.98811.997 9.4 3.95816.009 13.0 4.98815.996 12.9 4.95819.009 15.5 5.98818.996 15.4 5.95824.009 20.0 7.98523.996 19.8 7.94924.009 20.0 7.98523.996 19.8 7.949

T3 U2 V2 W2 X2 Y2 Z2UnitRef.JPM11 80 100 40 36 2JPM17 100 135 50 45 3JPM22 125 165 60 50 5JPM26 155 185 80 70 5JPM30 195 240 110 100 5

16.008 13.0 4.98815.997 12.9 4.95822.009 18.5 5.98821.996 18.4 5.95828.009 24.0 7.98527.996 23.8 7.94932.018 27.0 9.98532.002 26.8 9.94940.018 35.0 11.98240.002 34.8 11.939

PLUG-IN OUTPUT SHAFTS AVAILABLE WITH T3 DIMENSIONPLUG-IN AND SOLID OUTPUT SHAFTS AVAILABLE WITH T2 DIMENSION.

T2


www.renold.com

32

B B1 C D E Q D1 D2 K2 M N O PUnitRef.

S1CE

D

B

B1

T3

Q D1

PN

D2D

W2

V2

U2

X2

Y2Z2

C1

S2 S3

S4

4 HOLESK2 DIAM PCD


T2

FLANGE MOUNTING

U2 V2 W2 X2 Y2 Z2UnitRef.

JPM11 80 100 40 36 2JPM17 100 135 50 45 3JPM22 125 165 60 50 5JPM26 155 185 80 70 5JPM30 195 240 110 100 5

JPM11 55 26.43 52 42 42 78 3 7 10.0 115 60 140JPM17 85 40.55 78 60 67 98 3.5 11 10.0 130 85 160JPM22 105 47.85 90 80 90 126 3.5 12 12.0 165 105 200JPM26 117 50.33 97 92 102 104 4 12 14.5 215 105 250JPM30 135 58.8 105 100 120 156 4 12 14.5 215 130 250

16.008 13.0 4.98815.997 12.9 4.95822.009 18.5 5.98821.996 18.4 5.95828.009 24.0 7.98527.996 23.8 7.94932.018 27.0 9.98532.002 26.8 9.94940.018 35.0 11.98240.002 34.8 11.939

95.00094.946110.000109.946130.000129.937180.000179.937180.000179.937

PLUG-IN OUTPUT SHAFTS AVAILABLE WITH T3 DIMENSIONPLUG-IN AND SOLID OUTPUT SHAFTS AVAILABLE WITH T2 DIMENSION.


DIM D71M D80M D90L D100L D112MUnitRef.



D90S T3T2


www.renold.com

33

A B B1 C D E Q F2 G H L1 K G3UnitRef.

T1CE

HG

D

B

G

H

A

B1

K

Q

W1

V1

U1

X1

Y1 Z1

INPUT SHAFTDETAIL

F2R3

T2 T2

G3

H3L3

W2

V2

U2

X2

Y2Z2


L1


H3 L3 R3 T1 U1 V1 W1 X1 Y1 Z1UnitRef.JPM11 133 157 41 84 30 25 2.5JPM17 193 225 51 120 40 36 2JPM22 245 285 65 132 40 36 2JPM26 269 309 72 149 50 40 5JPM30 305 355 80 157 50 40 5

JPM11 28.57 55 26.43 52 42 42 78 3 35 70 84 7 60JPM17 44.45 85 40.55 78 60 67 98 5 47.5 95 130 12 84JPM22 57.15 105 47.85 90 80 90 126 6 57.5 115 160 12 110JPM26 66.67 117 50.33 97 92 102 140 6 72.5 145 190 14.5 122JPM30 76.2 135 58.8 105 100 120 156 6 80 160 200 14.5 135

12.008 9.5 3.98811.997 9.4 3.95816.009 13.0 4.98815.996 12.9 4.95819.009 15.5 5.98818.996 15.4 5.95824.009 20.0 7.98523.996 19.8 7.94924.009 20.0 7.98523.996 19.8 7.949



16.008 13.0 4.98815.997 12.9 4.95822.009 18.5 5.98821.996 18.4 5.95828.009 24.0 7.98527.996 23.8 7.94932.018 27.0 9.98532.002 26.8 9.94940.018 35.0 11.98240.002 34.8 11.949



www.renold.com

34




UnitRef.

CEH

G

D

B

G

H

S2

K

W2

V2

U2

X2

Y2Z2


Q

F2R3

T2 T2

G3

H3L3

L1

S1

C1

S3B1

S4


H3 L3 R3 T2 U2 V2 W2 X2 Y2 Z2UnitRef.JPM11 133 157 41 80 40 36 2JPM17 193 225 51 100 50 45 3JPM22 245 285 65 125 60 50 5JPM26 269 309 72 155 80 70 5JPM30 305 355 80 195 110 100 5

JPM11 55 26.43 52 42 42 78 3 35 70 84 7 60JPM17 85 40.55 78 60 67 98 5 47.5 95 130 12 84JPM22 105 47.85 90 80 90 126 6 57.5 115 160 12 110JPM26 117 50.33 97 92 102 140 6 72.5 145 190 14.5 122JPM30 135 58.8 105 100 120 156 6 80 160 200 14.5 135

16.008 13.0 4.98815.997 12.9 4.95822.009 18.5 5.98821.996 18.4 5.95828.009 24.0 7.98527.996 23.8 7.94932.018 27.0 9.98532.002 26.8 9.94940.018 35.0 11.98240.002 34.8 11.939

B B1 G3KL1HGF2QEDC




www.renold.com

35

UnitRef.

JPM11 50 70 24 8 22 40 M8 20 20 -13 8 29JPM17 50 70 24 8 28 40 M8 30 30 -10 13 37JPM22 65 89 28 10 30 47 M10 49.5 50.5 -8 18 27JPM26 65 89 28 10 30 47 M10 63.5 36.5 5.5 31.5 40.5JPM30 65 89 28 10 30 47 M10 56 44 12 38 47

A B K2 K3K1JIHGFEDC

The angle between the torque arm andthe input shaft must not exceed 30°and the arm must be positioned sothat it is in tension when loaded: seediagram where the torque reaction is

opposite to the direction of rotation ofthe output. It is preferred that thetorque arm is situated to that side ofthe gear unit which is adjacent to thedriven machine.

Where the duty involves reversing,two torque arms must be fitted,arranged for both directions ofrotation. Two holes are availablein the bracket to facilitate this.

500350500350650500650500650500

UnitRef.

JPM11 21 39 31 61 18.5 14 54 M8 12 - 23 17JPM17 30 50 40 100 28.5 17 72.5 M10 15 10.75 46 34JPM22 35 60 50 145 22.5 23.5 78.5 M12 18 - 80 59JPM26 43 74 62 117 36 31.5 110.5 M16 24 - 197 145JPM30 45 79 68 132 43.5 30.5 117 M16 24 - 197 145

A BBUFFER

TIGHTENING TORQUENm lb.ft

JIHGFEDC

D

C

AB

GE F J

HOLE FOR SIZE'H' BOLT

SKT HD SCREWCUSTOMERS SECURING PLATE(NOT SUPPLIED)

SLEEVENUT

WASHERBUFFER

jPM17 UNIT ONLY

A

30° MAX

A

2 HOLESFOR SIZE'H' BOLTS G

EBC

A

I J K2

F

SHAFTROTATION

K3

FK1

D

TORQUE RESTRAINT BRACKET

TORQUE ARM

TYPICAL BUFFER ARRANGEMENT

jPM Torque Restraints - Dimensions (mm)

www.renold.com

36

DESCRIPTIONUNIT SIZE

11 17 22 26 30

31:6 31:6 29:6 31:6 31:6

NOMINAL RATIO 5 TO 1

ACTUAL RATIO

1500 RPM INPUT

Output speed RPM 290.3 290.3 310.3 290.3 290.3

Input power kW 0.50 1.50 3.87 5.01 6.66

Output power kW 0.46 1.40 3.63 4.72 6.29

Output torque Nm 15.1 46 112 155 207

1000 RPM INPUT

Output speed RPM 193.5 193.5 206.9 193.5 193.5

Input power kW 0.33 1.02 2.96 3.63 5.06

Output power kW 0.30 0.95 2.75 3.39 4.74

Output torque Nm 15.0 47 127 167 234

750 RPM INPUT

Output speed RPM 145.2 145.2 155.2 145.2 145.2

Input power kW 0.25 0.79 2.28 2.79 3.80

Output power kW 0.23 0.72 2.11 2.58 3.53

Output torque Nm 14.9 47 130 170 244

500 RPM INPUT

Output speed RPM 96.8 96.8 103.4 96.8 96.8

Input power kW 0.17 0.52 1.57 1.90 2.54

Output power kW 0.15 0.48 1.43 1.74 2.34

Output torque Nm 14.8 47 133 172 255

250 RPM INPUT

Output speed RPM 48.4 48.4 51.7 48.4 48.4

Input power kW 0.08 0.26 0.81 0.98 1.47

Output power kW 0.07 0.23 0.72 0.88 1.33

Output torque Nm 14.6 46 134 175 262

Units to ATEX approval must be selected with aminimum service factor of 1.25

IMPORTANT

jPM Unit Ratings - Single Reduction

www.renold.com

37


11 17 22 26 30

29:4 29:4 29:4 29:4 29:4

NOMINAL RATIO 7.5 TO 1

ACTUAL RATIO

1500 RPM INPUT

Output speed RPM 206.9 206.9 206.9 206.9 206.9

Input power kW 0.48 1.45 2.75 4.11 5.83

Output power kW 0.44 1.34 2.56 3.84 5.47

Output torque Nm 20 62 118 177 253

1000 RPM INPUT

Output speed RPM 137.9 137.9 137.9 137.9 137.9

Input power kW 0.38 1.14 2.17 3.25 4.59

Output power kW 0.34 1.04 2.00 3.01 4.27


750 RPM INPUT

Output speed RPM 103.4 103.4 103.4 103.4 103.4

Input power kW 0.31 0.95 1.80 2.70 3.85

Output power kW 0.28 0.87 1.65 2.48 3.56


500 RPM INPUT

Output speed RPM 68.9 68.9 68.9 68.9 68.9

Input power kW 0.21 0.70 1.22 1.82 2.70

Output power kW 0.18 0.63 1.10 1.66 2.46


250 RPM INPUT

Output speed RPM 34.5 34.5 34.5 34.5 34.5

Input power kW 0.10 0.35 0.61 0.92 1.36

Output power kW 0.09 0.31 0.54 0.82 1.21



IMPORTANT


www.renold.com

38


11 17 22 26 30

29:3 29:3 29:3 29:3 29:3


ACTUAL RATIO

1500 RPM INPUT

Output speed RPM 155.2 155.2 155.2 155.2 155.2

Input power kW 0.41 1.25 2.23 3.30 4.70

Output power kW 0.37 1.13 2.06 3.05 4.36


1000 RPM INPUT

Output speed RPM 103.4 103.4 103.4 103.4 103.4

Input power kW 0.32 0.97 1.75 2.64 3.75

Output power kW 0.29 0.87 1.60 2.41 3.44


750 RPM INPUT

Output speed RPM 77.6 77.6 77.6 77.6 77.6

Input power kW 0.27 0.81 1.47 2.21 3.14

Output power kW 0.23 0.72 1.33 2.00 2.86


500 RPM INPUT

Output speed RPM 51.7 51.7 51.7 51.7 51.7

Input power kW 0.20 0.62 1.12 1.67 2.41

Output power kW 0.18 0.55 0.99 1.50 2.17


250 RPM INPUT

Output speed RPM 25.9 25.9 25.9 25.9 25.9

Input power kW 0.10 0.36 0.56 0.84 1.25

Output power kW 0.09 0.31 0.49 0.74 1.10



IMPORTANT


www.renold.com

39


11 17 22 26 30

37:3 37:3 37:3 37:3 37:3

NOMINAL RATIO 12.5 TO 1

ACTUAL RATIO

1500 RPM INPUT

Output speed RPM 121.6 121.6 121.6 121.6 121.6

Input power kW 0.35 1.07 2.14 3.03 4.28

Output power kW 0.31 0.95 1.94 2.77 3.91


1000 RPM INPUT

Output speed RPM 81.1 81.1 81.1 81.1 81.1

Input power kW 0.27 0.85 1.67 2.39 3.56

Output power kW 0.23 0.75 1.49 2.15 3.22


750 RPM INPUT

Output speed RPM 60.8 60.8 60.8 60.8 60.8

Input power kW 0.23 0.73 1.39 1.98 2.95

Output power kW 0.19 0.63 1.23 1.76 2.64


500 RPM INPUT

Output speed RPM 40.5 40.5 40.5 40.5 40.5

Input power kW 1.17 0.55 1.06 1.46 2.28

Output power kW 0.14 0.47 0.92 1.28 2.01


250 RPM INPUT

Output speed RPM 20.3 20.3 20.3 20.3 20.3

Input power kW 0.08 0.33 0.54 0.74 1.29

Output power kW 0.07 0.28 0.46 0.63 1.10



IMPORTANT


www.renold.com

40


11 17 22 26 30

31:2 31:2 29:2 31:2 31:2


ACTUAL RATIO

1500 RPM INPUT

Output speed RPM 96.8 96.8 103.4 96.8 96.8

Input power kW 0.30 0.88 2.01 2.82 3.58

Output power kW 0.26 0.77 1.79 2.53 3.22


1000 RPM INPUT

Output speed RPM 64.5 64.5 68.9 64.5 64.5

Input power kW 0.24 0.70 1.57 2.20 3.07

Output power kW 0.20 0.61 1.38 1.94 2.71


750 RPM INPUT

Output speed RPM 48.4 48.4 51.7 48.4 48.4

Input power kW 0.20 0.60 1.30 1.70 2.54

Output power kW 0.16 0.51 1.13 1.48 2.21


500 RPM INPUT

Output speed RPM 32.2 32.2 34.5 32.2 32.2

Input power kW 0.14 0.45 0.88 1.16 1.90

Output power kW 0.11 0.37 0.75 0.99 1.63


250 RPM INPUT

Output speed RPM 16.1 16.1 17.2 16.1 16.1

Input power kW 0.07 0.23 0.45 0.59 1.01

Output power kW 0.05 0.19 0.37 0.49 0.84



IMPORTANT


www.renold.com

41


11 17 22 26 30

41:2 41:2 39:2 41:2 41:2


ACTUAL RATIO

1500 RPM INPUT

Output speed RPM 73.2 73.2 76.9 73.2 73.2

Input power kW 0.22 0.71 1.45 2.03 2.85

Output power kW 1.18 0.60 1.26 1.77 2.51


1000 RPM INPUT

Output speed RPM 48.8 48.8 51.3 48.8 48.8

Input power kW 0.17 0.55 1.11 1.57 2.23

Output power kW 0.14 0.45 0.95 1.35 1.92


750 RPM INPUT

Output speed RPM 36.6 36.6 38.5 36.6 36.6

Input power kW 0.14 0.46 0.89 1.32 1.73

Output power kW 0.11 0.37 0.75 1.11 1.47


500 RPM INPUT

Output speed RPM 24.4 24.4 25.6 24.4 24.4

Input power kW 0.10 0.33 0.61 0.99 1.17

Output power kW 0.08 0.27 0.51 0.82 0.98


250 RPM INPUT

Output speed RPM 12.2 12.2 12.8 12.2 12.2

Input power kW 0.05 0.17 0.31 0.51 0.60

Output power kW 0.04 0.13 0.25 0.41 0.48



IMPORTANT


www.renold.com

42


11 17 22 26 30

25:1 25:1 49:2 49:2 25:1


ACTUAL RATIO

1500 RPM INPUT

Output speed RPM 60.0 60.0 61.2 61.2 60.0

Input power kW 0.23 0.58 1.08 1.61 2.34

Output power kW 0.18 0.47 0.92 1.38 1.98


1000 RPM INPUT

Output speed RPM 40.0 40.0 40.8 40.8 40.0

Input power kW 0.19 0.47 0.84 1.26 2.14

Output power kW 0.14 0.37 0.70 1.06 1.76


750 RPM INPUT

Output speed RPM 30.0 30.0 30.6 30.6 30.0

Input power kW 0.15 0.41 0.68 1.05 1.99

Output power kW 0.11 0.32 0.56 0.87 1.61


500 RPM INPUT

Output speed RPM 20.0 20.0 20.4 20.4 20.0

Input power kW 0.12 0.33 0.47 0.77 1.53

Output power kW 0.09 0.25 0.38 0.62 1.20


250 RPM INPUT

Output speed RPM 10.0 10.0 10.2 10.2 10.0

Input power kW 0.073 0.21 0.24 0.40 0.95

Output power kW 0.055 0.15 0.19 0.31 0.73



IMPORTANT


www.renold.com

43


11 17 22 26 30

30:1 30:1 30:1 30:1 30:1


ACTUAL RATIO

1500 RPM INPUT

Output speed RPM 50.0 50.0 50.0 50.0 50.0

Input power kW 0.19 0.61 1.23 1.59 2.05

Output power kW 0.15 0.48 1.00 1.30 1.69


1000 RPM INPUT

Output speed RPM 33.3 33.3 33.3 33.3 33.3

Input power kW 0.15 0.41 0.96 1.44 1.85

Output power kW 0.11 0.33 0.76 1.15 1.49


750 RPM INPUT

Output speed RPM 25.0 25.0 25.0 25.0 25.0

Input power kW 0.13 0.36 0.80 1.19 1.66

Output power kW 0.09 0.27 0.62 0.93 1.30


500 RPM INPUT

Output speed RPM 16.7 16.7 16.7 16.7 16.7

Input power kW 0.097 0.29 0.61 0.91 1.28

Output power kW 0.067 0.22 0.46 0.69 0.98


250 RPM INPUT

Output speed RPM 8.3 8.3 8.3 8.3 8.3

Input power kW 0.059 0.18 0.37 0.57 0.80

Output power kW 0.039 0.13 0.27 0.41 0.58



IMPORTANT


www.renold.com

44


11 17 22 26 30

40:1 40:1 40:1 40:1 40:1


ACTUAL RATIO

1500 RPM INPUT

Output speed RPM 37.5 37.5 37.5 37.5 37.5

Input power kW 0.14 0.41 0.84 1.25 1.63

Output power kW 0.10 0.31 0.65 0.97 1.26


1000 RPM INPUT

Output speed RPM 25.0 25.0 25.0 25.0 25.0

Input power kW 0.11 0.33 0.65 0.97 1.33

Output power kW 0.07 0.24 0.49 0.73 1.00


750 RPM INPUT

Output speed RPM 18.7 18.7 18.7 18.7 18.7

Input power kW 0.089 0.28 0.55 0.81 1.12

Output power kW 0.059 0.20 0.40 0.60 0.82


500 RPM INPUT

Output speed RPM 12.5 12.5 12.5 12.5 12.5

Input power kW 0.068 0.22 0.42 0.62 0.86

Output power kW 0.044 0.15 0.29 0.44 0.61


250 RPM INPUT

Output speed RPM 6.2 6.2 6.2 6.2 6.2

Input power kW 0.040 0.13 0.26 0.38 0.54

Output power kW 0.025 0.08 0.17 0.26 0.36



IMPORTANT


www.renold.com

45


11 17 22 26 30

50:1 50:1 50:1 50:1 50:1


ACTUAL RATIO

1500 RPM INPUT

Output speed RPM 30.0 30.0 30.0 30.0 30.0

Input power kW 0.104 0.33 0.63 0.92 1.29

Output power kW 0.070 0.23 0.46 0.69 0.97


1000 RPM INPUT

Output speed RPM 20.0 20.0 20.0 20.0 20.0

Input power kW 0.080 0.25 0.49 0.72 1.02

Output power kW 0.051 0.17 0.34 0.52 0.75


750 RPM INPUT

Output speed RPM 15.0 15.0 15.0 15.0 15.0

Input power kW 0.067 0.21 0.41 0.60 0.85

Output power kW 0.042 0.14 0.28 0.42 0.60


500 RPM INPUT

Output speed RPM 10.0 10.0 10.0 10.0 10.0

Input power kW 0.046 0.16 0.31 0.46 0.65

Output power kW 0.028 0.10 0.21 0.31 0.45


250 RPM INPUT

Output speed RPM 5.0 5.0 5.0 5.0 5.0

Input power kW 0.025 0.09 0.19 0.29 0.41

Output power kW 0.015 0.05 0.12 0.18 0.26



IMPORTANT


www.renold.com

46


11 17 22 26 30

60:1 60:1 60:1 60:1 60:1


ACTUAL RATIO

1500 RPM INPUT

Output speed RPM 25.0 25.0 25.0 25.0 25.0

Input power kW 0.086 0.26 0.49 0.72 1.01

Output power kW 0.055 0.18 0.34 0.52 0.74


1000 RPM INPUT

Output speed RPM 16.7 16.7 16.7 16.7 16.7

Input power kW 0.066 0.20 0.39 0.57 0.80

Output power kW 0.041 0.13 0.26 0.39 0.56


750 RPM INPUT

Output speed RPM 12.5 12.5 12.5 12.5 12.5

Input power kW 0.054 0.17 0.32 0.48 0.66

Output power kW 0.032 0.11 0.21 0.32 0.45


500 RPM INPUT

Output speed RPM 8.3 8.3 8.3 8.3 8.3

Input power kW 0.039 0.13 0.24 0.36 0.50

Output power kW 0.022 0.08 0.15 0.23 0.33


250 RPM INPUT

Output speed RPM 4.2 4.2 4.2 4.2 4.2

Input power kW 0.021 0.075 0.15 0.23 0.31

Output power kW 0.012 0.043 0.09 0.14 0.19



IMPORTANT


www.renold.com

47


11 17 22 26 30

70:1 70:1 70:1 70:1 70:1


ACTUAL RATIO

1500 RPM INPUT

Output speed RPM 21.4 21.4 21.4 21.4 21.4

Input power kW 0.070 0.23 0.43 0.63 0.85

Output power kW 0.040 0.15 0.28 0.43 0.59


1000 RPM INPUT

Output speed RPM 14.3 14.3 14.3 14.3 14.3

Input power kW 0.049 0.17 0.33 0.49 0.70

Output power kW 0.028 0.10 0.21 0.32 0.46


750 RPM INPUT

Output speed RPM 10.7 10.7 10.7 10.7 10.7

Input power kW 0.039 0.14 0.28 0.41 0.58

Output power kW 0.022 0.08 0.17 0.26 0.37


500 RPM INPUT

Output speed RPM 7.1 7.1 7.1 7.1 7.1

Input power kW 0.027 0.099 0.20 0.31 0.45

Output power kW 0.015 0.056 0.12 0.19 0.27


250 RPM INPUT

Output speed RPM 3.6 3.6 3.6 3.6 3.6

Input power kW 0.016 0.055 0.11 0.17 0.26

Output power kW 0.008 0.030 0.06 0.10 0.15



IMPORTANT


www.renold.com

48

Notes

www.renold.com

49

www.renold.com

Notes

50

www.renold.com

Notes

51

Terms and Conditions• In the interests of safety, customers are reminded that when purchasing anytechnical product for use at work (or otherwise), any additional or up-to-dateinformation and guidance, which it has not been possible to include in thepublication, should be obtained by you from your local sales office in relation to thesuitability and the safe and proper use of the product. All relevant information andguidance must be passed on by you to the person engaged in, or likely to beaffected by or responsible for the use of the product• The performance levels and tolerances of our product stated in this catalogue(including without limitation, serviceability, wearlife, resistance to fatigue,corrosion protection) have been verified in a programme of testing and qualitycontrol in accordance with Renold, independent and/or international standardrecommendations. No representations or warranties are given that our productshall meet the stated performance levels or tolerances for any given applicationoutside the performance levels and tolerances for the product’s own specificapplication and environment.

• Whilst all reasonable care in compiling the information contained in thiscatalogue is taken, no responsibility is accepted for errors.• All information contained in this catalogue is subject to change without notice.• The illustrations used in this catalogue represent the type of product describedbut the goods supplied may vary in some detail from those illustrated.• The right is reserved to make modifications to the product to meetmanufacturing conditions and/or developments (for example in design ormaterials).• Product can be supplied by Renold companies or representatives around theworld on the standard terms and conditions of sale of the company orrepresentative from which the product is purchased.• Copyright Renold Power Transmission Limited 2001. All rights reserved.Nothing contained in this publication shall constitute a part of any contract, expressor implied.

RENOLD A global power transmission group serving global

markets through an international network.

For your local Renold sales and service

location visit www.renold.com

Superior Technology. Global Expertise.

www.renold.com [email protected]

REN54/CATJPM/12.15/EA Business of Renold Power Transmission Ltd. Superior Gear Technology

jPM Series Worm Gear Units · Boom,luffing (2) Rotating,swingorslew (3) Tracking,drivewheels (4)...

Documents

Transcript of jPM Series Worm Gear Units · Boom,luffing (2) Rotating,swingorslew (3) Tracking,drivewheels (4)...