JOINTING METHOD FOR uPvc AND mPvc PIPE WITH INTEGRAL … · 2014-09-08 · JOINTING JOINTING METHOD...
Transcript of JOINTING METHOD FOR uPvc AND mPvc PIPE WITH INTEGRAL … · 2014-09-08 · JOINTING JOINTING METHOD...
JOINTING
JOINTING METHOD FOR uPvc AND mPvc PIPE WITH INTEGRAL Z-LOK JOINTS
All pressure pipes leave our factory with a 15 degree chamfered spigot and the depth of entry marked. It may, however, become necessary to cut a pipe in the field and should cut the length be required for further jointing, we recommend the following procedure for the spigot end.
1. Cleaning before jointing Remove shavings from the cut end of the pipe and smooth the pipe spigot if necessary. Clean and dry. The chamfer must be at 15 degrees to the pipe axis. While making the chamfer, the pipe wall thickness must not be reduced by more than half the original thickness.
2. Applying Z-Lok lubricant lubricate evenly around the spigot and the inside of the sicket, paying attention to the seal with suitably approved lubricant over half the spigot lenght. Move the spigot pipe so that the leading edge is just engaging the socket mouth before insertion.
3. Aligning the pipes Make sure that the pipes align correctly in both planes. This is most important, i.e do not try to align the spigot at an angle. The flexibility of pipe in sizes 110m and below may prevent correct alignment during assembly and therefore, the force required to assemble the joint should be applied as near to the spigot as possible with the socket held in position.
4. Assembling the joint Placing the tip of the spigot into the mouth of the socket, make certain both pipes are in alignment. Push the spigot into the socket, until it touches the seal. Ensure that contact is kept between spigot and seal and push firmly past the lip of the seal. Small bore pipes may be joined by hand but larger sizes may need an impact to push the spigot past the lip of the seal. Use a piece of wood or rubber to protect the end of the pipe being impacted to prevent damage to the pipe. Once the spigot has passed the lip of the seal the pipe will move easily into the socket.
5. The completed joint The spigot must be pushed into the socket up to the depth of entry mark.
OTHER FITTINGS
SEWER AND DRAIN FITTINGS
Moulded fittings are available in 110mm and certain fittings in 160mm (*). A range of fabricated fittings are available in sizes 100mm to 500mm.Included in the range are:Bends, junctions (*), adaptors, caps (*), inspection pipes, P traps, gully heads, sockets, connectors and rodding eyes.
SOIL AND WASTE FITTINGS
Moulded fittings in 50mm are available in this range.Included in this range are:Bends, junctions, sockets and adaptors.A range of fabricated fittings are also available.
COMPRESSION FITTING JOINTS
Assembly instructions 1. Cut the pipe square and clean. Partilly unscrew the nut.2. Push the pipe into the fitting over the clamp ring until the first stop, meaning you have reached the seal.3. Push the pipe through the seal until you reach the full insertion depth of the fitting.4. Screw on the nut tightly toward the body of the fitting.
HDPE STRUCTURED WALLED MANHOLES
PE-HD Piping
PE-HD (Black) pipe to SABS ISO 4427 and DIN 8074 (Supply of Water)PW 100, PE 80 & PE 63 Pipe Dimensions (SABS ISO 4427)
Larger sizes up to 1000mm available
(1) The standard ratio SDR corresponds to the quotient between the outside diameter and the wall thickness of the pipe. It is non-dimensional.(2) The nominal pressure PN corresponds ot the maximum permissible operating pressure of the pipe at 200C, in bar.(3) e = minimum Wall ThicknessThe above tables are based on the standards ISO 4427, DIN 8074, AS 4130 and ISO 4065/150 161/1The weights are calculated at the base of average diameter and thickness values, according to tolerances specified in the standardA range of butt weld and electrofusion fittings are available for the above piping.
HDPE structured walled manholes are fabricated from pipingand are complete with benching and pipe connections.Shaft diameters range from 350mm to 1800mm.Shaft stiffness selection, 2 kN/m 2, 4 kN/m 2,8 kN/m 2, is based on the installation site andcompactability of the backfill.Standard manhole covers and lids can be utilized withthe system, and will be selected accordign to traffic loads.When required stepladders can be fitted inside the manhole.
> >
>
Example:
Technical SpecificationsHigh Density Polyethylene - HDPE. Typical applications = Chemicals, Slurries, Potable Water and Compressed AirApplicable Standards - SABS ISO 4427: 1996 (Safety Factor PE 63 = 1.5, PE 80 = 1.25 and PE 100 = 1.25)
SDR Formula
SDR =
18016,4SDR 11 =
180mmOD
16,4mm wall thickness
Relationship between wall thickness and outside diameter (OD)
STANDARD DIMENSIONAL RATIO - SDR(1)
NOMINAL PRESSURE - PN(2)
PN 6,3 PN 10 PN 12,5
SDR 21 SDR 13.6 SDR 11
OD mm1620253240506375
e---
1,61,92,43,03,6
ID---
28,535,944,856,667,3
kg/m---
0,170,250,400,620,88
e-
1,9------
e-
2,3------
ID-
15,9------
ID-
15,0------
kg/m-
0,12------
kg/m-
0,14------
minimum wall thicknessnominal (minimum) outside diameter
NominalDiameter
STANDARD DIMENSIONAL RATIO - SDR(1) (PIPE SERIES)
NOMINAL PRESSURE - PN(2)
PE 100 PN 10
PE 63 PN 3,2 PE 63 PN 4 PE 80 PN 6 PE 80 PN 8 PE 80 PN 10 PE 80 PN 12,5 PE 80 PN 16 PE 80 PN 20
PE 63 PN 6,3 PE 63 PN 8 PE 63 PN 10 PE 63 PN 12,5 PE 63 PN 16
PE 100 PN 10 PE 100 PN 12,5 PE 100 PN 16 PE 100 PN 20 PE 100 PN 25
SDR 33 (S16) SDR 26 (S 12,5) SDR 21 (S 8,3) SDR 17 (S 8) SDR 13,6 (S 6,3) SDR 11 (S 5) SDR 9 (S 4) SDR 7,4 (S 3,2)
ID mm162025324050637590110125140160180200225
e------
2,32,32,83,43,94,34,95,56,26,9
ID------
58,170,284,2103,0117,0131,2149,9168,7187,3210,8
Kg/m------
0,50,60,81,21,51,92,53,13,94,9
e----
2,32,32,52,93,54,24,85,46,26,97,78,6
ID----
35,145,157,769,082,7101,3115,0128,8146,1165,7184,0207,2
Kg/m----
0,30,40,50,71,01,41,92,43,13,94,86,0
e--------
4,35,36
6,77,78,69,610,8
ID--------
81,099,0112,5126,0143,9162,1179,9202,4
Kg/m--------
1,21,82,32,93,84,85,97,5
e--
2,32,32,43,03,84,55,46,67,48,39,510,711,913,4
ID--
20,127,134,943,755,065,678,696,2109,4122,6140,0157,5175,0196,8
Kg/m--
0,20,20,30,50,71,01,52,22,83,54,65,97,29,2
e-
2,32,32,43,03,74,75,66,78,19,210,311,813,314,716,6
ID-
15,120,126,933,742,453,063,275,892,9105,6118,3135,1152,0168,9189,2
Kg/m-
0,10,20,20,40,60,91,31,82,73,44,35,67,28,811,4
e2,32,32,33,03,74,65,86,88,210
11,412,714,616,418,220,5
ID11,115,120,125,632,240,250,760,672,688,8100,8113,1129,0144,5160,6180,6
Kg/m0,10,10,20,30,40,71,11,52,23,24,25,26,98,810,913,8
e2,32,32,83,64,55,67,18,410,112,314
15,717,920,122,425,2
ID11,115,119,124,430,538,147,957,268,583,995,3106,7121,2136,4151,4170,3
Kg/m0,10,10,20,30,50,81,31,82,63,95,06,38,310,513,016,5
e2,32,83,54,45,56,98,610,312,315,117,119,221,924,627,430,8
ID11,114,117,622,728,335,344,753,163,877,987,898,3112,4126,5140,4158,0
Kg/m0,10,20,20,40,61,11,52,13,14,66,07,69,912,515,419,5
NomOD
uPvc PVC-U PRESSURE PIPESuPvc Pipes are manufactured as follows:• To SABS 966 Part 1 specifications• Size range 20mm - 500mm outside diameter• Pressure range - PN 4-PN25• Plain edged in 20mm - 40mm sizes• With integral socket in 50mm - 500mm sizes• Design stress - 10 MPA in sizes up to 90mm and PN 4 to PN 20• Design stress - 10 MPA in sizes 110mm - 500mm in PN 4• Light blue in colour• Lengths normally 6 metres
SEWER PIPES - PVC-U PIPESStructured Walled Pvc Multi-layer Sewer Pipes aremanufactured as follows:• To SABS 1601• With foamed core in a multi-layer configuration• In sizes 110 mm - 250mm• With pipe stiffnees of 200 kPA and 400 kPA• With plain ends in 110 mm• With integral sockets - 100mm - 250mm• Beige in colour
PVC-U SOLID WALLSEWER PIPESSuprador Sewer Pipes aremanufactured as follows:• To SABS 791 specifications• Size range 110mm - 500mm• Pipe stiffness 100kPA (Class 51)• Pipe stiffness 300kPA (Class 34)• Plain ended 110mm• With integral sockets - 110mm - 500mm• Beige in colour
Pipe dimensions and massPVC-U SABS 966 PART 1uPvc
Larger sizes up to 500mm available
SizeOD2025324050637590110125140160200
mm
1.51.51.51.82.22.52.83.24.0
mm
1.51.51.92.22.72.83.253.554.055.0
mm
1.51.82.22.83.33.94.154.75.25.957.45
mm
0.151.92.32.93.64.35.15.456.156.97.859.75
mm1.51.92.43.03.74.75.66.77.18.05
910.2512.8
mm2.02.53.13.04.96.17.38.78.79.8511
12.5515.7
mm
10.612.1013.5015.4019.2
kg/m
0.380.490.580.821.231.571.952.563.93
kg/m
0.300.380.600.831.201.331.712.152.84.38
kg/m
0.240.360.540.851.201.681.942.513.144.116.42
kg/m
0.190.290.450.691.081.532.172.533.274.15.358.36
kg/m0.150.230.360.560.861.371.942.773.274.225.36.9210.82
kg/m0.170.270.430.631.061.672.373.403.975.136.438.4013.12
kg/m
4.86.267.8210.1915.89
Structured wall PVC-U Sewer Pipes
200KPA 400KPASizeOD110169200250
mm2.754.25.06.3
Kg/m0.912.273.385.56
mm3.24.86.07.3
Kg/m1.222.413.755.96
PVC SOIL, WASTE &VENT PIPEPVC Soil, Waste and Vent Pipes aremanufactured as follows:• To SABS 967• Size range 40 mm - 110mm• Plain ended• UV stabilized• White in colour
PVC-U Soil and Vent Pipe
Pipe Mass (kg/m)
Size Wall thickness(mm)
4050110
0.410.571.80
2.32.43.6
PVC-U MULTILAYERSOIL AND VENT PIPEPVC Soil & Vent Pipes aremanufactured as follows:• To JASWIC and EN 1453-1• Size range 110mm• Plain ended• UV stabilized• White in colour
PVC-U Multilayer Soil and Vent Pipe
Pipe Mass (kg/m)
Size Wall thickness(mm)
110 1.22 3.2
PVC-U Solid Wall Sewer Pipes
Class 51-100KPA Class 34-300KPA SizeOD110160200250315355400500
mm2.23.23.94.96.27.07.810
Kg/m1.232.563.936.
9.5712.0015.3623.11
mm3.24.75.97.39.210.611.715.45
Kg/m1.743.655.78.8213.9617.7422.4434.09
WAM GARDEN HOSES
WAM Industrial10 year design lifeBurst pressure of 4 000 kPa
WAM garden hoses have a PVC inner liner and outer cover, reinforced with polyester yarn
FITTINGSCompression fittings and clammp saddles
SABS 645-170 type 11
Internal Diameter (mm) 12210
20338
25538Mass per metre (g)
WAM Standard6 year design lifeBurst pressure of 2 800 kPa
Internal Diameter (mm) 12100
20200Mass per metre (g)
WAM Medium7 year design lifeBurst pressure of 3 000 kPa
Compression fittings range:16mm - 110mmPressure rating: 16mm - 110mm PN16
Quick coupling valve:3/4” and 1”Key for quick coupling valve: 3/4”
Polypropylene threaded fittings:1/2” - 3”
NOTE: Refer to price list for details of full product range and dimensions, local and internationalcertification and assembly instructions
Clamp saddle ranges and pressure rating:PN10 unreinforced 20mm x 1/2” - 160mm x 2”Clamp saddles with stainless steel reinforcing ring and Alprene flat gasket:PN16 unreinforced 25mm x 1/2” - 160mm x 2”PN10 bar unreinforced 20mm x 1/2” - 315mm x 2”
Internal Diameter (mm) 12150
20268Mass per metre (g)