Jll Presentation Cpa And Bohler Arch And Laser Scanning
-
Upload
richbutkus -
Category
Documents
-
view
674 -
download
3
Transcript of Jll Presentation Cpa And Bohler Arch And Laser Scanning
Civil Engineering · Architectural Engineering · Permitting · Landscape Architecture Land Surveying · Environmental and Geotechnical Engineering · Traffic Engineering
Philadelphia, PA 267.402.3400 · Center Valley, PA 610.709.9971 · Chalfont, PA 215.996.9100Warren, NJ · Southborough, MA · Albany, NY · Ronkonkoma, NY · Towson, MD · Bowie, MD · Sterling, VA
Warrenton, VA · Fort Lauderdale, FL · Tampa, FL
Bohler Engineering & Affiliates
Introduction• Frank Coulter, PE, Architectural Project Manager (BEI)
• Buck Collins, Director of Client Services (BEI)
• Richard A. Butkus, Jr., General Manager (CPA)
Bohler Services
ARCHITECTURAL ENGINEERING
• Preliminary Client Consultation • Feasibility Studies • Site Investigation Reports • Building Code Research and Analysis • Existing/As-built Condition Surveys and Report • Space Planning • Concept Development • Color Renderings • Full Building Design/Engineering: Architectural, Structural,
Mechanical, Electrical, Plumbing • Construction Document Development • Materials Specification • Permit Expediting • Contractor Bid Coordination • Project Management • Shop Drawing/Submittal Review • Construction Administration
Building Alteration/Renovation ServicesMacy’s/Starbuck’s, John Wannamaker Building, Center City Philadelphia, PA: This Starbucks project required a
unique approach. The photos shown are of the world famous John Wannamaker building in Center City. Macy’s wanted a “destination” type café for their customers and Starbuck’s was the perfect partner for this venture; however Starbuck’s needed to maintain an independent exterior presence as well. The result was subtle conversion of one of the display windows into an exterior entrance. Due to the historic nature of the building, Bohler assisted our Clients in achieving both their goals while preserving and maintaining the historic quality of the building.
Before After
Building Alteration/Renovation Services
Potbelly Sandwich Works, 1200 Walnut St., Philadelphia, PA: Bohler provided design/permitting assistance for the exterior restoration and tenant installation of a new sandwich deli. This project involved design and permitting of a new exterior ADA ramp/stair to overcome a +/- 2’-0” grade differential.
Before After
Control Point Services
PROFESSIONAL LAND SURVEYING• Laser Scanning• True View Virtual Environments• 3D Modeling• 3D Renderings • Aerial Ground Control & Photogrammetry• Architectural Surveys• As-Built & Final Surveys• Interior and Exterior Architectural Building As-Builts and Space
Validation• Boundary, Topographic & Utility Surveys• ALTA/ACSM Land Title Surveys• Anchor Bolt/Steel Framing Plans• Façade Surveys• Geodetic Control Surveys• Hydrographic Surveys• Property and Easement Descriptions• Subdivisions & Lot Consolidation Plats
BIM Modeling
White Plains HospitalCath Lab Interior SurveyApproximately 5000 s.f.
Field:• Leica C10 HDS Laser
Scanner• 16 hours of Field time to
Produce the point cloud
Office:• 7 hours of Tech time to
register point cloud and create truview
• 34 Hours in Cyclone for 3D Modeling
MEP EXAMPLE
White Plains HospitalMechanical/Chiller Room
Field:• Leica C10 HDS Laser
Scanner• 3 hours in room
Office:• 10 hours to Model MEP
elements in Cyclone
Institutional Example
130’ Tall Historic Building on Campus of Georgia Tech
Field:• 4 Set-ups• 4 Hours to finish Data
Collection
Office:• 6 Hours in CloudWorx for
plan creation• 0.5 Hours to clean-up and
Plot
Infrastructure Examples
Bridge Viaduct Interchange – Steel Models and Clearances
Field:• Leica C10 HDS Scanner• 3 hours in field – Closed
Traverse on Local Coordinate System
• 4 Hours to finish Data Collection
Office:• 12 Hours in Cyclone for
Modeling• No Plan Delivered – Only
Screenshots• 0.5 Hours for Screenshots
and Report
Preservation Example
Historic Building Face
Field:• Leica C10 HDS Scanner• 3 hours in field • 2 Hours to finish Data Collection
Office:• 12 Hours in Cyclone for 3D Model
Infrastructure Examples
500’ of Divided Highway with Elevation View of Historic Hotel
Field:• Leica C10 HDS Scanner• 4 hours in field• 4 Hours to finish Data Collection• Registered to State Plane Coordinate System
Office:• 2 Hour in Cyclone for TIN Creation• 5 Hours in CloudWorx for Topographic Plan
Creation• 0.5 Hours to Clean-up and Plot Topographic
Plan• 6 Hours in CloudWorx for Elevation View Plan
Creation
Laser Scan Surveying & Optional Deliverables
Control Point Associates / Bohler Engineering will utilize a Leica C10 HDS (High Definition Scanner) to perform multiple scans for the interior or exterior project areas. The resulting scan will produce a point cloud comprised of millions of data points with an accuracy of 1/8th of an inch or greater.
This point cloud may be utilized to produce a wide range of deliverables. These can range in
complexity and accuracy from a simple 2 dimensional floor plan to a complex 3 dimensional intelligent BIM (Building Information Model) deliverable, depending on the client's needs.
Level and Complexity of Deliverables
WHO is going to be using the scan data? Architects and Construction Managers that require exact measurements and deliverables in Revit format or marketing and other less technical users that only need the data presented in its simplest form or in a the more common AutoCad format.
WHAT is the purpose of the laser scan? New Construction, Interior Modifications, Space Planning or MEP projects?
Marketing Materials for Prospective Tenants/Buyers or Building Façade Scans for Historic Preservation… WHERE is the scanning technology used? The scans are used anywhere inside, outside or near your space of
building. An individual office, utility room, basement, lobby, plenum, roof or parking lot all go thru changes and alterations that require permanent plans at the greatest level of accuracy.
WHEN will the scan information be used? This technology has been available for 10+ years, but only recently has
the industry begun to treat it as the technology of choice for surveying. Most prominent Architects, Construction Managers, Contractors and Engineers have begun utilizing and often requiring laser scanning to dramatically speed delivery, reduce errors in measurements and cost overruns. The data will be used for all future building operations, potentially as long as the building remains standing.
HOW is the scan to be used? Basic modeling or for technical drawings for precise Cost Estimating and Project
Permitting
Levels of Development (LOD)
Levels of Development (LOD)
First Niagara Bank: First Niagara Bank expanded into the Philadelphia market late in 2009, when they purchased Harleysville National Bank. Many of the branch locations did not have any building plans or site survey plans associated. Bohler was able to rapidly initiate and complete base building measurements and develop building area plans and photo location plans so that the Client could better understand and analyze each branch included in the purchase.
Exterior Site Services
Segmental Retaining Wall Concrete Retaining Wall
Bohler Engineering’s experience in Architectural Engineering is not limited to building design. Often times land development teams require retaining wall design to be included within the site design package. Bohler provides these design services “in-house” for our Clients, thus saving both time and money during the design process.
Office LocationsPhiladelphia, Pennsylvania
1515 Market Street, Suite 920
Philadelphia, PA 19102
(P) 267.402.3400 (F) 267.402.3401
Center Valley, Pennsylvania
Stabler Corporate Center
3701 Corporate Parkway, Suite 200
Center Valley, PA 18034
(P) 610.709.9971 (F) 610.709.9976
Chalfont, Pennsylvania
New Britain Corporate Center
1600 Manor Drive, Suite 200
Chalfont, PA 18914
(P) 215.996.9100 (F) 215.996.9102
Albany, New York
Bowie, Maryland
Fort Lauderdale, Florida
Ronkonkoma, New York
Sterling, Virginia
Southborough, Massachusetts
Tampa, Florida
Towson, Maryland
Warren, New Jersey (Headquarters Office)
Warrenton, Virginia