JAMIESON FENCE SUPPLY GATE PRODUCTS AND PHOTO GALLERY

“24 locations with the products you want, the support you need and the service you deserve.”

Traditional Steel Pipe Gates

V-Track

cantilever gates

Aluminum Cantilever Gates

TrusTrac™ Single Track Gates

TrusTracII™ Double Track Gates

Box Gates

PowerTrac™ Cantilever

PowerTrac™ Canted Wheel

Aluminum V-Track Gates

ValuTrac™ Slide Gates

Overhead I-Beam Track Gates

I-Trac™

Crash Gates

CGS™ Crash Gate Systems

Custom Gates

SLIDE GATE PRODUCTS

… to Homeland Security

Residential and Commercial…

Filler materials extend through the tail section

of each gate for safety and symmetry. Thus, each

gate can open to either side- eliminating the need

to specify opening direction.

Jamieson’s TrusTrac™ gates are a premier line

of aluminum cantilever sliding gates.

Utilizing our proprietary truck and enclosed

track system, this single panel gate can span

large gate openings with minimal deflection or

resistance. All gates are fabricated and fully

welded under factory controlled conditions,

ship ready for immediate installation ¹ and

include all hardware for manual operation.

TrusTrac™ Gate Series Typical use

Max single

drive gate

opening

Max double

drive gate

opening

TrusTrac™ Series 1000 Standard use 22’ 44’

TrusTrac™ Series 2000 Medium duty use 28’ 56’

TrusTrac™ Series 3000 Heavy duty use 34’ 68’

TrusTracII™ Series 3000 Heavy duty use with large gate openings 40’ 80’

¹ Where the overall length of the gate exceeds

shipping constraints, the gate is shipped in two

sections with prefabricated splice provisions for

simple reassembly at the job site.

At the heart of each TrusTrac™

gate is Jamieson’s proprietary

truck and track system. Our 10”

truck assembly is unequalled in

the industry. Each of the (8)

wheels on our truck assemblies

are cylindrical bearings with a

5,400 lb static load. With a

robust body and mounting system,

the entire truck assembly has

been tested and certified for a

17,500 lbs peak load.

TrusTrac™ geometry and section

widths are specifically designed

for increased strength and

rigidity to resist deflection over

long spans and in high wind-load

conditions. Our 6061-T6

aluminum track extrusion weighs

4.8 lbs/ft by itself- over 6½

lbs/ft in conjunction with the top

horizontal member!

TrusTrac™ gate frames are constructed

from durable 6063-T52 structural aluminum

to provide maximum life, durability and rust

resistance.

Each gate is custom fabricated to the exact

opening to achieve superior balance, rigidity

and squareness. Each bay is equidistant, a

maximum of 6’ wide and braced with solid

gusset plates.

End bays include additional heavy wall

bracing to provide additional strength,

greater chain link tension (if applicable)

and the opportunity to relocate operator

chain brackets or drive rail from the end

of the gates- thus eliminating a

protrusion.

Whether creating original ornamental

concepts, matching to custom fencing,

eliminating riveted/field assembled gates,

designing for high security or unique

applications, our Engineering and custom

fabrication team specialize in creating custom

designs, specifications and manufacturing the

gate to meet your requirements.

CUSTOM DESIGNS & FABRICATION

F2200 and UL325 Compliant

Match Existing or Custom Fence

Square, Round, Solid or Tubular

Pickets

Custom Arched Rails

Ameristar® Impasse® Pales

80’ Double Drive Ornamental

Cantilever Gate

11’-6” tall x 45’ Double Drive Custom

Ornamental Cantilever Gate

TrusTrac™ Gate Series Typical use

Max single

drive gate

opening

Max double

drive gate

opening

PowerTrac™ Series 4000 Cantilever Box Gate 60’ 120’

PowerTrac™ Series 4100 Canted Wheel Box Gate (Track) 200’ 400’

Jamieson’s PowerTrac™ gates are a premier line

of aluminum box frame sliding gates. Utilizing

our robust design, these gates can span large

openings with ease of movement and minimal

deflection. PowerTrac™ gates are available as

cantilever (Series 4000) or ground track

(Series 4100).

PowerTrac™ gates have been certified to 130 MPH wind loads in coastal locals. As site

conditions (soil, wind exposure level, building codes, etc) are an essential element of the

evaluation, Jamieson provides an option for your job-specific wind-load certifications.

Series 4000 Cantilever Box Gates

Jamieson’s Series 4000 PowerTrac™ Cantilever

Gates utilize our proprietary heavy duty truck

assemblies and enclosed track system. As with

our premier TrusTrac™ gate products, each of

the (4) 10” heavy duty truck assemblies have

been tested and certified for a 17,500 lbs

peak load.

PowerTrac™ Box Gates are designed and

manufactured to meet your standard or

unique aesthetic requirements. Our

Engineering team and custom fabrication

shop can provide design support, develop

3 part specs & manufacture the gate to

meet your requirements. Mill finish

aluminum & powder coated finishes are

available.

Series 4000 Box Gate Construction

PowerTrac™ gate frames are

constructed from durable 6063-T52

structural aluminum to provide maximum

life, durability and rust resistance.

Enhanced material weight & usage

provides additional strength and

support in critical frame areas for

greater impact and wear resistance.

Each gate is custom fabricated to

achieve superior squareness, balance

and rigidity. All bay widths are ≤ 6’

wide, equidistant and braced with (4)

welded solid gusset plates. A minimum

of (3) cross braces per primary vertical

member and alternating diagonal cross

braces top & bottom span the length of

the gate to join the front and rear

panels as a rigid, single piece box frame.

Unless otherwise requested, filler

materials (such as chain link) are

factory installed with splicing

provisions (sleeves, drilled holes &

hardware) and all hardware for manual

operation provided. Simple re-assembly

and installation is provided for at the

job site.

Jamieson’s Series 4100 PowerTrac™ Canted

Wheel Box Gates are a ground track

aluminum frame box gate system designed

for very large gate openings (up to 200’

single drive gate openings).

208’ Single Drive Canted Wheel Gate

The entire gate length is fabricated

in modular 24’ foot sections in the

manufacturing facility to ensure

squareness, parallelism and

integrity. the gate is separated into

halves to meet shipping constraints.

Filler materials such as chain link or

ornamental pickets are factory

installed. Splicing provisions (sleeves,

drilled holes & hardware) and all

hardware are provided for manual

operation. Simple re-assembly and

installation is provided for at the job

site.

• 3” square gate frame, 2” sq. primary

verticals diagonal cross bracing 1” sq.

• I Beam Rail system with steel rebar

anchors fabricated at Jamieson and

galvanized after fabrication

• Fabricated and assembled wheel

assemblies & Cradles, galvanized after

Fabrication

-Track Slide Gates

¹ Where the overall length of the gate exceeds

shipping constraints, the gate is shipped in two

sections with prefabricated splice provisions for

simple reassembly at the job site.

Jamieson’s ValuTrac™ Aluminum V-Track

Sliding Gates are capable of spanning large

openings with stability unequaled in the

industry. All gates are fully welded under

factory controlled conditions.

Each gate series is constructed from specific

structural members determined by the

application and gate span to strengthen the

gate and improve stability.

ValuTrac™

Gate Series Typical use

Max single

drive gate

opening

Max double

drive gate

opening

Series 1500 Standard use 20’ 40’

Series 2500 Medium duty use 30’ 60’

Series 3500 Heavy duty use 50’ 100’

Series 4500 Heavy duty use with large gate openings 60’ 120’

-Track Slide Gates

constructed from durable 6063-T52

structural aluminum to provide

exemplary life, durability and rust

resistance.

custom fabricated to the exact

opening to achieve superior balance,

rigidity and squareness.

Each bay is equidistant, a maximum of

6’ wide and braced with (4) welded solid

gusset plates.

-Track Slide Gates

End bays include a heavier wall vertical

member with horizontal bracing and a

second vertical support member provide

improved durability, greater chain link

tension (if applicable) and the opportunity

to relocate operator chain brackets or

drive rail from the end of the gate- thus

eliminating a protrusion.

6-inch solid steel power wheels

weighing 12.5 lbs each with 5,000

lb capacity and sealed bearings are

included with each ValuTrac™ gate

produced. The wheels are mounted

inside custom wheel-wells to

maintain low ground clearance. The

wheels are maintenance free with

no grease fittings.

HEAVY DUTY MAINTENANCE

FREE WHEELS:

I- -Beam Gates

I-Trac™ Gate

Series Typical use

Max span

of opening Gate Frame Material

Series 6200 Industrial, commercial & security applications 20’ Aluminum & Steel

Series 6300 Heavy duty, high security applications 30’ Aluminum & Steel

Series 6400 Heavy duty, large openings, high security 45’ Aluminum

Series 6600 Heavy duty, very large openings, high security 60’ Aluminum

Jamieson’s I-Trac™ gate systems are a

complete line of overhead I-Beam sliding

gates for correctional facilities, Sally

ports & high security applications. Single

or double drive gate openings can range up

to 16’ maximum clear height and spans of

60’ on the aluminum gate series & 30’ with

steel.

engineered for wind loads up to

110 MPH @ Wind Exposure ‘C’.

As most typical I-Trac™ gates exceed shipping

constraints, the gate is shipped in sections with

splice provisions for simple and immediate reassembly

at the job site.

I- -Beam Gates

• designed to the exact span, weight &

wind load.

• designed for strength, balance,

rigidity and endurance.

• AWS certified manufacturing

operations

• Complete system package

(superstructure plus gate).

• Adjustability in each bay through the

entire gate length.

• Filler materials extend through the

tail section of each gate, thus making

each gate reversible and able to open

to either side.

I- -Beam Gates

Jamieson’s proprietary aluminum track is

mounted to the bottom of the engineered

I-Beam at the factory for perfect

alignment, optimal splice locations (if

applicable) and ease of installation at

the job site. The enclosed track

provides 2,500 lb vertical reaction

load, eliminates snow or ice buildup and

potential tampering that can be found

with external rollers.

Heavy duty 10” truck assemblies, each

with (8) 5,400 lb cylindrical bearings,

are certified for a 17,500 lbs peak load.

The quantity of trucks required is based

on the opening & gate length and are

mounted to the top of the gate frame to

carry the gate with high reliability and

minimal resistance. Posts, double post assemblies and

hanging brackets are designed and

fabricated to the specific application.

I- -Beam Gates

There are few limitations to securing, latching

or locking I-Trac™ gates. Whether manual,

electronic or hydraulic, Jamieson can assist in

selection, system design, integration, 3-part

specifications and supply.

Our goal is to provide you the highest quality

gate system with simplified installation and high

reliability.

Security Gates

Jamieson’s Crash Gate Systems (CGS™) can

adapt any Jamieson proprietary sliding

gates to K4, K8 or K12 engineered crash

ratings.

All CGS™ assemblies include Gate,

Superstructure, cable systems, locking

column, bollard posts and automation for

total system requirements.

Please call Jamieson for more detailed

information.

· PIPE CANTILEVER GATES

· TRUSTRAC™ ALUMINUM

ENCLOSED TRACK

CANTILEVER GATES

· VALUTRAC™ V-TRACK

GATES

· I-TRAC™ OVERHEAD I-BEAM

GATES

· POWERTRAC™ CANTILEVER

BOX GATES

· POWERTRAC™ CANTED

WHEEL BOX GATES

Welded & bent frame residential gates

Pre-fabricated pedestrian gates

Ornamental Estate Swing Gates

Large opening swing gates

Specialty and Custom Gates

SWING GATE PRODUCTS

PRE-HUNG FOR EASE OF INSTALLATION

LATCHING AND ACCESS CONTROL OPTIONS

PRE-SET HINGES FOR EASE OF INSTALLATION

FILLER CHOICES AVAILABLE

HYDRAULIC DOOR CLOSER (OPTION)

SERIES 8000 PRE-FAB PEDESTRIAN GATES

Jamieson’s Series 8000 pre-hung pedestrian (walk)

gates ship ready for immediate installation at the

jobsite. All gates and components in this series are

manufactured and assembled by our team of

fabricators and assemblers to meet your custom

specifications.

SERIES 8000 PRE-FAB PEDESTRIAN GATES Series 8000 gate installation is simply a matter of

setting the two posts in concrete piers. The bottom

cross-brace is removed or set in a shallow trench

excavated between the footings. The gate is then

inserted into the footing, braced upright and concrete

poured.

Where magnetic latches or electronic access control

features are pre-assembled, all wiring is run at the

factory and fed through a ¾” coupling 6” below grade

on the latch side of the gate.

There are almost as many ways to gain entry or exit a gate as there are gates. Most

options required are difficult products to field assemble- such as magnetic, electronic or

combination locks, panic bars, hydraulic closers and so forth. Our specialty is to provide

you custom products preassembled in a factory controlled environment by our team of

installation experts. This means better quality controls for you and a more efficient and

cost effective means of installation.

SERIES 8000 PRE-FAB PEDESTRIAN GATES

Standard Series 8000 gate frames are

manufactured from 2” square x 3/16”

wall heavy steel tubing with 4” posts.

The posts can be round schedule 40

(typical for chain link) or square heavy

wall (ornamental). Cross-bracing

between the posts above & below the

gate frame provides rigidity,

squareness and stability during

transportation and installation.

The gate is welded to the door frame

with Elite Power Hinges. These hinges

are heavy duty and super quiet with

double ball bearings that pivot on a

3/4" ground and tempered solid

stainless steel shaft. They are

maintenance free and self lubricating

to provide long life with free gate

movement. The weight capacity per

pair is 1000 lb.

SERIES 8000 PRE-FAB PEDESTRIAN GATES

For gates installed between existing

columns or posts, Jamieson applies the

same fit-for-use and installation friendly

principles. Our pre-fabricated hinge

plates include either fixed or adjustable

barrel hinges with the mating

requirements either pre-drilled or

fabricated onto the opposing half of the

gate frame. At installation, it is only a

matter of determining location, then

drilling and lagging the hinge plate to

the column/post followed by hanging

the pre-set gate frame.

The completed product is available with

either a galvanized or powder coated finish

to match the aesthetics of the project.

Material substitutions are welcome and our

design team will assist with custom

drawings and specifications to meet your

specific application.

SERIES 8400 ESTATE GATES

Jamieson’s Series 8400 Estate gates are

custom designed and manufactured aluminum

and steel frame ornamental single and double

drive swing gates. These gates are ideally

suited for residential and light commercial

properties.

All gates are fully welded under

factory controlled conditions, ship

ready for immediate installation and

include all hardware for manual

operation.

Automation and associated hardware

integration can be designed, specified

and supplied by Jamieson.

SERIES 8400 ESTATE GATES

From the simple to the elaborate, Jamieson can

incorporate your standard or unique

ornamental design into our proven durable

gates.

Standard and custom powder coated colors are

available. Material substitutions are welcome

and our design team will assist with custom

drawings and 3-part specifications to meet your

specific application.

For those projects that require:

• a higher quality gate than typically

provided by mass producers or

importers of fence panels

• a collaborative effort to match your

design concept into a well built gate

frame.

• a flexible company that works with

you

• design expertise and custom

manufacturing capabilities.

SERIES 8400 ESTATE GATES

Series 8400 gate frames are made from

domestic materials and are more

substantial than typically used by most

conventional manufacturers. Our

manufacturing operations custom fabricate

each product to our exacting standards

with AWS certified welders and welding

procedures.

Jamieson applies fit-for-use and

installation friendly principles from

design through manufacturing. As such,

there is minimal to no gate assembly at

the job site.

All gates (within shipping constraints)

are 100% welded in the controlled

environment of our manufacturing

facility.

SERIES 8400 STADIUM GATES

The result is a solid weldment that doesn’t

rattle when used and there is no

assembling numerous parts that can be

lost or missing.

all hinges and hardware are preinstalled

(if possible) at the factory and include a

complete range of hinges from self-

closing to high weight capacity. We also

provide an option for custom hinge plates

for installation between existing columns

or posts.

installation is simply a matter of setting

the posts or mounting the hinge plate.

With minimal assembly, there is minimal

packaging and cleanup required after

installation.

LOGOS AND INSTALLED FEATURES • STEEL & ALUMINUM

• CUSTOM CAD DESIGNS

• CUSTOM MATCHED COLORS

• LASAR, PLASMA & WATER JET

CUTTING CAPABILITIES

• MULTILE FRAMING & MOUNTING

OPTIONS

Our specialty is to provide you custom

products preassembled in a factory

controlled environment by our team

of installation experts. This means

better quality controls for you and a

more efficient and cost effective

means of installation.

There are many different devices

used to control access or

exiting through a gate. Fitting

these devices to a gate in the

field can be difficult, time

consuming and potentially cause

significant damage to gate

appearance.

¹ Where the overall length of the gate exceeds

shipping constraints, the gate is shipped in two

sections with prefabricated splice provisions for

simple reassembly at the job site.

XLG Gate Series Frame Materials

Max single

drive gate

opening

Max double

drive gate

opening

Series 8630 3” square frame, 2” x 3” internal vertical members 30’ 60’

Series 8650 2” x 5” frame, 4 ½” x 3” I-Beam vertical members 60’ 120’

SERIES 8600 LARGE OPENING GATES

Jamieson’s XLG Series 8600 gates are custom

manufactured aluminum frame swing gates for

very large gate openings. These gates are ideally

suited for Industrial, Commercial, Governmental

or other security sensitive applications. All

gates are fully welded under factory controlled

conditions, ship ready for immediate installation

and include all hardware for manual operation.

SERIES 8600 LARGE OPENING GATES

Series 8600 gate frames are made from

durable structural aluminum and

fabricated by AWS certified welders and

welding procedures. Each gate is custom

fabricated to Jamieson’s exacting

standards and braced with solid gusset

plates to maintain squareness and

rigidity. Stainless steel aircraft truss

cable assemblies with adjustable

turnbuckles are installed throughout

the entire gate length to provide both

significant and fine tuning adjustments.

Hinge vertical members are from heavy wall

tubing, predrilled and sleeved for the mating

hinge. In chain link applications, both end

vertical members are reinforced with

horizontal bracing and an additional vertical

support member for greater chain link

tension.

Internal primary and intermediate vertical

members are sized to the application to

provide superior stability and sway

resistance.

71’ DOUBLE DRIVE SWING GATE

SERIES 8600 LARGE OPENING GATES

HINGES AND THE XLG

SUPPORT PACKAGE

Jamieson has a full line of hinge

assemblies for Series 8600 gates that

range up to a 3,000 pound capacity per

hinge.

The Series 8600 XLG Support Package

consists of an upper truss cable

assembly (either one or two depending

on panel length), a hinge-end vertical

member extension, an extended gate

post, brackets and upper hinge.

The XLG Package includes an extended

vertical hinge member and additional

hinge above the gate. Opposite this

hinge is a mounting bracket that swings

with the gate and has a stainless steel

aircraft truss cable attached. This

cable extends approximately 2/3 of the

gate length, which is then attached to

a turnbuckle and bracket welded to

the top horizontal member. The

turnbuckle can then adjust the gate

to the correct elevation.

120’ DOUBLE DRIVE

SERIES 8600 LARGE OPENING GATES

Post and footing sizes and

specifications are functions of state

& local specifications and

regulations, soil conditions, wind

load, size/weight of the gate, wind

blockage of the infill and

potentially other job specific

conditions.

Actual design and specifications must

be determined specifically for the

project by Jamieson, the Architect,

Engineer of Record or other

technically capable resource.

Complementing our

branch capabilities is

our Access Control &

Engineered Gate

Division, headquartered

in Houston, Texas. This

resource provides

state-of-the-art

technical & design

support with enhanced

fabricating capabilities.

ENGINEERING & MANUFACTURING CENTER

Certified to AWS D1.1/D1.1M and D1.2/D1.2M

POST TRUCK BRKT. U-BOLT LOWER GUIDE BRKT. COLLECTOR

4" ROUND 274003-E4 209007 274005-UL 274011-UL

4" SQUARE 274003-E4 209007-SQ 274005-UL 274011-UL

6 5/8" ROUND 274003-E6 200000-265 274005-6 274012-UL

6" SQUARE 274003-E6 200000-269 274005-6 274012-UL

TABLE III: HARDWARE GUIDE

WIRE SIZE

3/16"

1/4">30' 1/2" x 6"

TABLE IV: CABLE TRUSSING

GATE OPENING TURNBUCKLE SIZE

<30' 3/8" x 6"

EXTENDED TRUCK BRACKET(REF. TABLE III)

TABLE 1: TRUCK ASSEMBLY CRITERIA:

TRUSS CABLE(REF. TABLE IV)

BOTTOM HORIZONTAL

CABLE CLAMP

9 GA. SMOOTH WIRE

TENSION BAR

1/4" GUSSETTYP AT EACH CORNER/ EACH BAY

TURNBUCKLE(REF. TABLE IV)

SQUARE/ ROUND UL COLLECTOR(REF. TABLE III)TOP HORIZONTAL

BARBWIRE 4 PT. 12.5 GA.(OPTIONAL)

T6061-T6 ALUM. TRUSS TRAC

LOWER GUIDE BRACKET(REF. TABLE III)

3" UL BOX ROLLERS

> 24'

GATE OPENING

= 24'

274010

PARTNUMBER

274006

10"

LENGTH

6"

8

# BEARINGS/ WHEELS

4

NOTE: ALL SERIES 3000 GATES USE 10" TRUCKS

Single Track Parts List:

INSTRUCTION MANUALS

Recommended Tools:

Tape measure

Surveyors instrument

String line

Stakes

String line level

24” to 48” Carpenter’s level

Post hole auger (or digger)

Cement Trowel

Fence Pliers

Standard (flat) screwdriver

15/16” Open end wrench

15/16” Socket, ratchet & drive extension

¾” socket or open (or box) end wrench

6” or 8” crescent wrench

CUSTOM MANUALS & SPECIFICATIONS

ENGINEERING

Solid Models

Jamieson’s in-house engineering

capabilities include 3D CAD drafting

and solid modeling. This is used for

any applicable custom product to

check fit, form & function on moving

parts, determine weights and balance,

optimize center of gravity, create

detailed manuals and to simplify

installation at the job site.

ANIMATION FOR FIT-FORM-FUNCTION

fit-form-function

& visualization

Animation

Detailing

PROJECT SUPPORT Our Engineering Center provides

total quality in the design, lay out

and fabrication of your total

requirement, making your product

fit-for-use to simplify installation

at the job site.

• All custom gates run-off at factory

before shipping

• All products assembled and

fabricated to fullest extent possible

PENTAGON RAILING

• 18 ELEVATION (SLOPE) CHANGES

• 860’ PRE-FABRICATED RAIL SECTIONS

• 84 UNIQUE PLATED POSTS WITH

DESIGNATED LOCATION TO FOLLOW SLOPE

• STAINLESS MARINE TURNBUCK/CABLE

Assembly

AWS certified

Testing

HARDWARE Jamieson provides a complete line of gate

hardware and accessories. Our

manufacturing operations are certified to

AWS D1.1/D1.1M and D1.2/D1.2M and

provides the technological & manufacturing

expertise to provide for custom

applications. Compliant to UL325 & ASTM

F2200-02 Safety Standards

Cantilever Gate

Hardware

Fittings

Gate

Hardware

12300-A AMELIA DRIVE

HOUSTON, TX 77045

888/286-3362

WWW.JAMIESONFENCE.COM

FOR FURTHER INFORMATION

WWW.ASTM.ORG

WWW.DASMA.COM

WWW.UL.COM

Jamieson is committed to providing quality perimeter security products and services. Because

safety is an important part of Jamieson's design and manufacturing criteria, we follow the

standards developed by Underwriter’s Laboratory (UL 325) and ASTM F2200 as developed by

ASTM International. While these safety standards are specific to automated gates, Jamieson

also chooses to apply them to manual gates to restrict hazards such as protrusions, pinch

points and entrapment zones. As such, our engineering & manufacturing team has developed a

full line of compliant components & hardware. All access control products that we offer

are specifically selected for the proper class of gate usage.

SAFETY POLICY

USE PROPER CARE & PRECAUTION AT ALL

TIMES WHEN OPERATING GATES

NEVER “RIDE” THE GATE

ALWAYS USE PROPER SAFETY EQUIPMENT WHEN SERVICING

GATE OR GATE HARDWARE

DO NOT DISABLE , REMOVE OR MODIFY ANY SAFETY

FEATURES FROM THE PRODUCT

INSTALL ALL WARNING SIGNS & PLACARDS

DO NOT ADD ANY FEATURES THAT PROTRUDE FROM THE BODY OF

THE GATE GREATER THAN ½”

THERE IS NO SUBSTITUTE FOR COMMON SENSE

CORPORATE OFFICE

P.O. Box 769008 Dallas, TX 75376-9008

214-339-8384

800-527-6464 Fax: 214-337-2061

MANUFACTURING & ENGINEERING

12300-A Amelia Drive

Houston, TX 77045-4814 713-434-7907

888-286-3362

Fax: 713-434-7924

JAMIESON LOCATIONS

GEORGIA MISSOURI TENNESSEE TEXAS TEXAS TEXAS

50 Bellamy Court 5201 East 9th Street 405 Hillcrest Drive 9520 Brown Lane 4343 Forest Lane 6504 Smithfield Road

Stockbridge, GA 30281 Kansas City, MO 64124 Bluff City, TN 37618 Austin, TX 78754 Garland, TX 75042 North Richland Hills, TX 76182

678-379-4006 816-231-1062 423-391-0500 512-837-7808 972-494-3200 817-498-0347

888-400-8332 800-777-2584 888-391-0501 800-777-1106 800-777-3245 866-498-0347

Fax: 678-379-4007 Fax: 816-231-6088 Fax: 423-391-0580 Fax: 512-837-8135 Fax: 972-276-0783 Fax: 817-498-6455

LOUISIANA OKLAHOMA 2709 John Deere Drive 10813 I-35 South 14214 Aldine Westfield 6916 N.E. Loop 410

3116 S. Council Road Knoxville, TN 37917 Burleson, TX 76028 Houston, TX 77039 San Antonio, TX 78219

7335 Julie Frances Drive Oklahoma City, OK 73179 865-540-9983 817-293-6972 281-590-5097 210-433-7267

Shreveport, LA 71129 405-745-6969 877-740-9983 866-510-5796 800-777-5097 800-777-1143

318-687-4433 800-777-6404 Fax: 865-540-5146 Fax: 817-551-5734 Fax: 281-590-5148 Fax: 210-661-5581

800-777-4435 Fax: 405-745-6886

Fax: 318-687-4487 2345 Frisco 1915 Empire Central 12300-A Amelia Drive 12930 Sugar Ridge Blvd

Memphis, TN 38114 Dallas, TX 75235 Houston, TX 77045 Stafford, TX 77477

MINNESOTA 5305 S 24th West Ave 901-743-8282 972-241-5827 713-434-7907 281-879-6200

Tulsa, OK 74107 888-892-3362 800-777-5827 888-286-3362 888-268-3362

3401 85th Avenue 918-770-0813 Fax: 901-743-1742 Fax: 972-247-5769 Fax: 713-434-7924 Fax: 281-879-5558

Minneapolis, MN 55443 866-242-0040

763-424-7950 Fax: 918-447-3746 4221 Platinum Way 1143 W. Hurst Blvd 5004 FM 2767

800-777-2430 Dallas, TX 75237 Hurst, TX 76053 Tyler, TX 75708

Fax: 763-424-2422 214-339-8384 817-772-8001 903-597-0463

800-527-6464 800-591-8505 800-777-5988

MISSISSIPPI Fax: 214-337-2061 Fax: 817-772-8002 Fax: 903-595-3221

815 Hwy 475 South 9650 John W. Elliott Dr. 1310 Jarvis Street

Pearl, MS 39208 Frisco, TX 75033 Lubbock, TX 79403

601-936-4111 469-252-8075 806-744-2977

866-936-3362 800-442-6283 800-777-2978

Fax: 601-936-9987 Fax: 469-252-8078 Fax: 806-741-1998