Isometric projection

27
Isometric Projection

Transcript of Isometric projection

Page 1: Isometric projection

Isometric Projection

Page 2: Isometric projection

Isometric Projection• Isometric projection is a method for

visually representing three-dimensional objects in two dimensions in technical and engineering drawings. It is an axonometric projection in which the three coordinate axes appear equally foreshortened and the angles between any two of them are 120 degrees.

Page 3: Isometric projection

Isometric Terminology• The three coordinate axes are called isometric

axes

• Any line parallel to isometric axes is called isometric line

• A  non-isometric line is a line not parallel   to   any   one   of   the three isometric axis

• In isometric projection of cube, the faces of the cube and any plane parallel to them is called isometric planes

Page 4: Isometric projection

Isometric Scale• True lengths of the edges of the

object are equally foreshortened• Correct isometric projection can be

drawn using an isometric scale (always smaller than ordinary scale)

Page 5: Isometric projection

Isometric Drawing• Isometric

Projection: Drawing prepared with isometric scale on isometric axes

Isometric Drawing: Drawing prepared with ordinary scaleon isometric axes

Page 6: Isometric projection

Steps for construction of Isometric :

Step 1Isometric sketches begin with defining isometric axes, three lines, one vertical and two drawn at 30° from the horizontal.

Page 7: Isometric projection

Step 2Three lines of the isometric axes represent the three primary dimensions of the object: width, height, and depth

Page 8: Isometric projection

Step 3Draw the rest of the isometric block.

Page 9: Isometric projection

Step 4Add details to the block starting from the front face. Then add details to the other faces.

Page 10: Isometric projection

Step 5Darken all visible lines to complete the isometric sketch. (make sure that construction lines are light)

Page 11: Isometric projection

• Axonometric projection shows all 3 dimensions, length, width and height.

• The isometric lines are only drawn to scale. Objects composed entirely of isometric lines can be drawn by taking all measurements parallel to main edges of the enclosing box.

• Non-isometric lines are drawn by transferring the ordinates (which are on isometric lines) of the end of the lines

• Inclined and oblique surfaces are drawn using end coordinates. Box construction and offset measurements are common methods

• In  an  isometric  drawing,  an angle never appears in its true size. Angles, irregular curves require special techniques

Page 12: Isometric projection

Objects with Normal SurfacesMake an Isometric Drawing with corner A at the bottom

Page 13: Isometric projection
Page 14: Isometric projection

Objects with Oblique Surfaces• Make an Isometric Drawing with

corner A at the bottom

Page 15: Isometric projection
Page 16: Isometric projection

Objects with Non-isometric Lines• Make an Isometric Drawing with apex

A facing front

Page 17: Isometric projection

Non-isometric lines are drawn with box construction and offset measurements

Non-isometric lines are not drawn in true length in isometric drawing (BA is shorter than CA in this drawing)

Page 18: Isometric projection

Irregular Objects

• Make an Isometric Drawing of the following irregular object (pyramid)

Page 19: Isometric projection

• OA and OB offsets help to locate apex O• Complete box construction may not be needed in each case

Page 20: Isometric projection

Objects with Circular Geometry

•A circle in a orthographic projection will appear as an ellipse in an isometric drawing.•Instead of actual ellipses often approximate ellipses are drawn for isometric drawing.•Four-centre ellipses are used to approximate ellipses on isometric planes.

How to draw four-centre ellipse???

Page 21: Isometric projection

•Draw  the  isometric centre  lines  of  the circle. Using  the  centre  lines,  draw an isometric square with sides equal to the diameter of  the  circle.•From  the  near  corners  of  the  box,  draw two large arcs with radius R, using the two red points as centres. •Draw the two smaller arcs with radius r, using two green points as centres.

Page 22: Isometric projection

Cylinder

Page 23: Isometric projection

Objects with Circular Geometry

Page 24: Isometric projection

Objects with Non-Circular Curved Surfaces

• Make an Isometric Drawing of the following curved object

Page 25: Isometric projection

•A line that appears as a noncircular curve in a normal orthographic view of an object appears as a non-isometric line in an isometric drawing.•Curves may be drawn using a series of points by measuring along the normal lines in the  orthographic  view  (offset measurements) and  transferring  these points on isometric drawing. Accuracy increases with number of points.

Page 26: Isometric projection

Presented ByEnrollment No. Name130170111090 RANA ABHIMANYU S.

130170111091 RATHAWA JAYDEVSINH

130170111092 RATHOR VIJENDRASINGH R.

130170111094 RATHWA VIKAS P.

130170111090 RUDRA PAWAN M.

Page 27: Isometric projection

Hope you enjoyed our presentation.

Thank you