INDIAN STANDARDS METALLURGICAL ENGINEERING DIVISION COUNCIL (MTD) SR. No. CAT DESCRIPTION IS 8: 1983 MTD

15 High heat duty fireclay refractories (forth revision)

IS 277: 1992 MTD 4 Galvanized steel sheet (plain and corrugated)(fifth revision)(Amendments 3)

IS 483: 1972 MTD 15

Fireclay refractories for oil-fired boiler furnaces of naval ships (first revision)

IS 513: 1994 MTD 4 Cold rolled low carbon steel sheets and strips (fourth revision) (Amendment 1)

IS 814: 1991 MTD 11

Covered electrodes for manual metal arc welding of carbon and carbon manganese steel (fifth revision) (Amendments 3)

IS 815: 1974 MTD 11

Classification coding of covered electrodes for metal arc welding of structural steels (second revision) (superseded by IS 814:1991)

IS 822: 1970 MTD 11

Code of procedure for inspection of welds.

IS 1161: 1958 MTD 19

Steel tubes for structural purpose (fourth revision)

IS 1182: 1983 MTD 21

Recommended practice for radiographic examination of fusion welded butt joints in steel plates (second revision)

IS 1239 (Part 1):1990

MTD 19

Mild steel tubes, tubulars and other wrought steel fittings: Part 1 Mild steel tubes (fifth revision) (Amendments 5)

IS 1239 (Part 2):1992

MTD 19

Mild steel tubes, tubulars and other wrought steel fittings: Part 2 Mild steel tubulars and other wrought steel pipe fittings (fourth revision) (Amendments 2)

IS 1279: 1958 MTD 19

Electrically welded mild steel boilers and superheater tubes for design steam temperatures not exceeding 155 degree centigrade or 850 degree centigrade (superseded by IS 1914)

IS 1337: 1993 MTD 20

Electroplated coatings of hard chromium for engineering purpose (third revision)

IS 1395: 1982 MTD 11

Low and medium alloy steel covered electrodes for manual metal arc welding (third revision)

Is 1403 (Part 1):1993

MTD 32

Mechanical testing of metals – reverse bend test: Part 1 Sheet and strip (second revision) (Amendment 1)

Is 1442: 1964 MTD 11

Covered electrodes for metal arc welding of high tensile structural steel (revised) (superseded by IS 814)

IS 1526: 1960 MTD 15

Sizes and shapes for firebricks (Amendment 1)

IS 1528 (Part 10): 1974

MTD 15

Determination of size of refractory bricks (first revision)

IS 1545: 1994 MTD 8 Solid drawn copper and copper alloy tubes for condenser and heat exchanger (third revision) (Amendments 3)

IS 1570: 1996 MTD 16

Schedules for wrought steels for general engineering purpose (revised)

IS 1570 (Part 1):1978

MTD 16

Schedules for wrought steels: Part 1 steels specified by tensile and / or yield properties (first revision)

IS 1570 (Part 2/Sec 1): 1979

MTD 16

Schedules for wrought steels: Part 2 Carbon steels (unalloyed steels) sec 1 wrought products (other than wire) with specified chemical composition and related properties (first revision)

IS 1570 (Part 2/Sec 2): 1987

MTD 16

Schedules for wrought steels: Part 2 Carbon steels (unalloyed steels) sec 2 Carbon steel wires with related properties (first revision)

IS 1570 (Part 3):1979

MTD 16

Schedules for wrought steels: Part 3 carbon and carbon manganese free cutting steels (first revision)

IS 1570 (Part 4):1988

MTD 16

Schedules for wrought steels: Part 4 Alloy steels (alloy constructional and spring steels) with specified chemical composition and mechanical properties (first revision)

IS 1570 (Part 5):1985

MTD 16

Schedules for wrought steels: Part 5 Stainless and heat resisting steels (second revision)

IS 1570 (Part 6):1996

MTD 16

Schedules for wrought steels: Part 6 Carbon and alloy tool steels (first revision)

IS 1570 (Part 7):1992

MTD 16

Schedules for wrought steels: Part 7 Steels for elevated temperature service (creep resistant steels)

IS 1586: 1988 MTD 3 Method for Rockwell hardness test for metallic material (scales A-B-C-D-E-F-G-H-K) (second revision)

IS 1598: 1977 MTD 3 Method for izod impact test of metals (first revision) IS 1599: 1985 MTD 3 Method for bend test (second revision) (superseding IS

1692:1974, Is 3260:1960 and IS 4598:1968) IS 1608: 1995 MTD 3 Mechanical testing of metals – tensile testing (second

revision) (superseding IS1521, 1663, 1816, 1894, 2078, 2654, 2655, 2656, 2657, 2658, 4713 and 8285)

IS 1870: 1965 MTD 16

Comparison of Indian and overseas standards for wrought steels for general engineering purpose.

IS 1871 (Part 1):1987

MTD 16

Commentary on Indian standard schedules for wrought steels: Part 1 Steels specified by Tensile and yield properties (Complementary to IS 1570(Part 1): 1978 (first revision)

IS 1871 (Part 2):1987

MTD 16

Commentary on Indian standard schedules for wrought steels: Part 2 Carbon steels (unalloyed steels) (Complementory to Is 1570 Part 2): 1979 (first revision)

IS 1871 (Part 3):1987

MTD 16

Commentary on Indian standard schedules for wrought steels: Part 3 Carbon and carbon manganese free cutting steels [complementary to IS 1570(Part 3): 1978 (first revision)

IS 1875: 1992 MTD 18

Carbon steel billets, blooms, slabs and bars for forgings (fifth revision) (Amendment 2)

IS 1914 (Part 1 to 4): 1982

MTD 19

Carbon steel boilers tubes and superheater tubes (second revision)

IS 1977: 1996 MTD 4 Low tensil structural steels (third revision)

IS 2002: 1992 MTD 4 Steel plate for pressure vessels for intermediate & high temperature service including boilers (second revision) (Amendment 2)

IS 2004: 1991 MTD 18

Carbon steel forgings for general engineering purpose (third revision)

IS 2041: 1995 MTD 4 Steel plates for pressure vessels used at moderate and low temperature (second revision) (Amendment 1)

IS 2042: 1972 MTD 15

Insulating bricks (first revision) (Amendment 1)

IS 2049: 1978 MTD 1 Colour code for the indentification of wrought steels for general engineering purpose (first revision) (Amendment 1)

IS 2062: 1992 MTD 4 Steel for general structural purpose (fourth revision) (superseded IS: 226:1975) (Amendments 4)

IS 2328: 1983 MTD 3 Method for flattening teat on metallic tubes (first revision) IS 2329: 1985 MTD 3 Method for bend test on metallic tubes (first revision) IS 2330: 1986 MTD 3 Method for flanging test on metallic tubes (first revision) IS 2335: 1985 MTD 3 Method for drift expanding test on metallic tubes (first

revision) (Amendment 1) (Superseding IS 2348:1963 and IS 4599:1968)

IS 2478: 1991 MTD 21

Glossary of terms relating to industrial radiography (second revision)

IS 2595: 1978 MTD 21

Code of practice for radiographic testing (first revision)

IS 2598: 1966 MTD 21

Safety code for industrial radiographic practice

IS 2611: 1964 MTD 18

Carbon chromium molybdenum steel forgings for high temperature services

IS 2811: 1987 MTD 12

Recommendations for manual tungsten inert gas arc welding of stainless steel (first revision)

IS 2856: 1987 MTD 17

Carbon steel castings for pressure containing parts suitable for high temperature service (fusion welding quality) (third revision) (Amendment 1)

IS 2986: 1990 MTD 17

Steel castings for marine engines and boilers (second revision)

IS 3038: 1992 MTD 17

Martensitic stainless steel and alloy steel castings for pressure containing parts suitable for high temperature service (third revision)

IS 3407 (Part 1):1983

MTD 3 Method for creep testing of steel at elevated temperature: Part 1 Tensile creep testing (first revision) (superseded IS 3408: 1965) @ A3 = Reaffirmed 1989

IS 3407 (Part 2):1983

MTD 3 Method for creep testing of steel at elevated temperature: Part 2 Tensile creep stress rupture testing (first revision) (superseded IS 3409: 1965)

IS 3410: 1993 MTD 3 Metalic materials – determination of liner thermal expansion (first revision)

IS 3415: 1998 MTD 21 Glossary of terms used in magnetic particle flow detection (second revision)

IS 3422: 1966 MTD 4 Code of practice for packaging of steel and steel products for export purpose

IS 3444: 1987 MTD 17 Corrosion resistant alloy steel and nickel base castings for general applications (Second revision) (Amendment 1)

IS 3502: 1994 MTD 4 Steel chequered plates (second revision)

IS 3503: 1966 MTD 4 Steel for marine boilers, pressure vessels and welded machinery structures

IS 3531: 1997 MTD 24 Glossary of terms relating to corrosion of metals (second revision)

IS 3589: 1991 MTD 19 Seamless or electrically welded steel pipes for water, gas and sewage (168.3 to 2032 mm outside diameter) (second revision)

IS 3600 (Part 1):1985

MTD 11 Methods of testing fusion welded joints ad weld metal in steel: Part 1 Cruciform fillet weld tensile test

IS 3600 (Part 2):1985

MTD 11 Methods of testing fusion welded joints ad weld metal in steel: Part 2 Beam impact (charpy V-notch) test

IS 3600 (Part 3):1984

MTD 11 Methods of testing fusion welded joints ad weld metal in steel: Part 3 Transverse tensile test on butt welds

IS 3600 (Part 4):1984

MTD 11 Methods of testing fusion welded joints ad weld metal in steel: Part 4 Longitudinal tensile test on cylindrical weld metal test pieces on butt welds

IS 3600 (Part 5):1983

MTD 11 Methods of testing fusion welded joints ad weld metal in steel: Part 5 Tranverse root and face bend test on butt welds

IS 3600 (Part 6):1983

MTD 11 Methods of testing fusion welded joints ad weld metal in steel: Part 6 Transverse side bend test on butt welds

IS 3600 (Part 7):1985

MTD 11 Methods of testing fusion welded joints ad weld metal in steel: Part 7 Longitudinal root and face bend test on butt welds

IS 3600 (Part 8):1983

MTD 11 Methods of testing fusion welded joints ad weld metal in steel: Part 8 Nick break test and fillet weld fracture test

IS 3600 (Part 9):1985

MTD 11 Methods of testing fusion welded joints ad weld metal in steel: Part 9 Macro and micro examination

IS 3601: 1984 MTD 19 Steel tubes for mechanical and general engineering purpose (first revision) (Amendments 2)

IS 3609: 1966 MTD 19 Chrome molybdenum steel, seamless, boiler and superheater tubes (Amendments 2)

IS 3613: 1974 MTD 11 Acceptance tests for wire flux combination for submerged arc welding (first revision) (Amendment 1)

IS 3658: 1999 MTD 21 Code of practice for liquid penetrant flaw detection (second revision)

IS 3703: 1980 MTD 21 Code of practice for magnetic particle flaw detection (first revision)

IS 3711: 1990 MTD 3 Wrought steel – selection and preparation of samples and test pieces for mechanical tests (first revision)

IS 3747: 1982 MTD 4 Hot rolled steel plates and sheets for flanging and pressing (first revision) (superseded by IS 5986:1992)

IS 4260: 1986 MTD 21 Recommended practice for ultrasonic testing of butt welds in ferritic steel (second revision)

IS 4353: 1995 MTD 12 Submerged arc welding of mild steel and low alloy steels - Recommendations (first revision)

IS 4522: 1986 MTD 17 Heat resistant alloy steel and nickel base castings (second revision)

IS 4712: 1984 MTD 19 Forged steel socket welding fittings (first revision) (Amendment 1)

IS 4853: 1982 MTD 21 Recommended practice for radiographic inspection of fusion welded butt joints in steel pipes (first revision)

IS 4943: 1968 MTD 11 Assessment of butt and fillet fusion welds in steel sheet, plate and pipe

IS 5206: 1983 MTD 11 Covered electrodes for manual metal arc welding of stainless steel and other similar high alloy steels (first revision)

IS 5334: 1981 MTD 21 Code of particle for magnetic particle flaw detection of welds (first revision)

IS 5511: 1991 MTD 11 Covered electrodes for manual metal arc welding of cast iron (first revision) (Amendment 1)

IS 5530: 1987 MTD 12 Recommendations for production, rectification and repair of steel castings by metal arc welding process (first revision)

IS 5555: 1970 MTD 24 Code of practice for conducting field studies on atmospheric corrosion of metals (Amendment 1)

IS 5788: 1986 MTD 6 Iron castings with spheroidal or nodular graphite for pressure containing parts for use at elevated temperature (first revision) (Amendment 1)

IS 5789: 1993 MTD 6 Austenitic spheroidal graphite iron casting for pressure containing parts suitable for low temperature service (first revision)

IS 5986: 1992 MTD 4 Hot rolled steel plates, sheets strips and flats for flanging and forming operation (first revision) (Amendments 4)

IS 6009: 1970 MTD 20 Method for evaluation of result of accelerated corrosion test

IS 6286: 1971 MTD 19 Seamless and welded steel pipes for sub zero temperature service (Amendment 1)

IS 6392: 1971 MTD 19 Steel pipe flanges (Amendment 1) IS 6410: 1991 MTD 21 Magnetic flaw detection links and powders (first revision) IS 6419: 1996 MTD 11 Welding rods and bare electrodes for gas shielded arc

welding of structural steels (first revision) IS 6431: 1972 MTD 11 Tolerances on dimensions of plates cut by flame IS 6601: 1987 MTD 17 Permissible deviations in chemical composition for

products analysis of steel castings (with amendment No.1) (first revision) (Amendment 1)

IS 6630: 1972 MTD 19 Seamless ferritic alloy steel pipes for high temperature steam service (first revision)

IS 6911: 1992 MTD 16 Stainless steel plate, sheet and strip (first revision) (Amendment 1)

IS 6913: 1973 MTD 19 Stainless steel tubes for the food and beverage industry IS 7307 (Part 1):1974

MTD 11 Approval tests for welding procedures: Part 1 fusion welding of steel (Amendment 1)

IS 7310 (Part 1):1974

MTD 11 Approval tests for welders working to approved welding procedures: Part 1 fusion welding of steel

IS 7318 (Part 1):1974

MTD 11 Approval tests for welders when welding procedure approval is not required: Part 1 Fusion welding of steel

IS 7598: 1990 MTD 1 Classification of steels (first revision) IS 7899: 1992 MTD 17 Alloy steel castings suitable for pressure service (second

revision) IS 8062 (Part 1):1976

MTD 24 Code of practice for cathodic protection of steel structures: Part 1 General principles

IS 8062 (Part 3):1977

MTD 24 Code of practice for cathodic protection of steel structures: Part 3 Ship’s hull

IS 8629 (Part 1):1977

MTD 24 Code of practice for protection of iron and steel structures from atmospheric corrosion: Part 1 General principles of corrosion and its prevention (Amendment 1)

IS 8629 (Part 2):1977

MTD 24 Code of practice for protection of iron and steel structures from atmospheric corrosion: Part 2 Pretreatment (Amendment 1)

IS 8629 (Part 3):1977

MTD 24 Code of practice for protection of iron and steel structures from atmospheric corrosion: Part 3 Protection schemes (Amendment 1)

IS 8780: 1978 MTD 21 Code of practice for non destructive testing of steel castings (Amendment 1)

IS 8791 IS 8800: 1997 MTD 17 Technical delivery conditions for steel castings (excluding

investment castings) (third revision) IS 8849: 1991 MTD 26 Glossary of terms relating to fuel fired industrial furnaces IS 9158: 1979 MTD 19 Cold drawn high pressure fluid power cylinder tubes

(Amendment 1)

IS 9172: 1979 MTD 24 Recommended design practice for corrosion prevention of steel structures

IS 9180: 1991 MTD 26 Recommendations for performance rating of fuel fired furnace (first revision)

IS 9444: 1980 MTD 26 Code of practice for installation of oil supply units for fuel fired furnaces

IS 9516: 1980 MTD 16 Heat resisting steel (Amendment 1) IS 9683: 1980 MTD 18 Carbon and low alloy steel forgings for fired and unfired

pressure vessels IS 10178: 1995

MTD 12 Gas shielded metal CO2 arc welding of structural steels recommendations (first revision)

IS 10219: 1982

HMD 17

Purchaser’s data sheet for tube nest evaporation plants

IS 10234: 1982

MTD 12 Recommendations for general pipeline welding

IS 10801: 1984

MTD 12 Recommended procedure for heat treatment of welded fabrications

IS 11083: 1984

MTD 3 Method for evaluation of friction and wear properties of materials against steel surface

IS 11368 (Part 1): 1985

MTD 11 Comparison of Indian and overseas classifications and coding of welding filter materials: Part 1 Flux coated mild steel and medium tensile steel electrodes for manual metal arc welding (Amendment 1)

IS 11428 (Part 1-3): 1985

MTD 19 Wrought carbon steel butt welding pipe fittings

IS 11587:1986

MTD 4 Structural weather resistant steels

IS 11630: 1986

MTD 21 Method of ultrasonic testing of steel plates for pressure vessels and special applications

IS 11714 (Part 1 to 5): 1986

MTD 19 Steel tubes for heat exchangers

IS 11732: 1995

MTD 17 Acceptance standards for liquid penetrant inspection of steel castings (first revision)

IS 12145: 1987

MTD 18 Quenched and tempered alloy steel forgings for pressure vessels

IS 12146:1987

MTD 18 Carbon manganese steel forgings for pressure vessels

IS 12148: 1987

MTD 21 Guidelines for requirements for non destructive testing agencies

IS 12368: 1988

MTD 26 Guidelines for design and construction of hot air generators

IS 12392: 1988

MTD 26 Code of practice for design, manufacture and testing of metallic recuperators

IS 12442: 1988

MTD 27 Seamless and welded titanium and titanium alloy tubes for condensers and heat exchangers

IS 12457: 1988

MTD 4 Code of practice for evaluation repairs and acceptance limits of surface defects in steel plates, and wide flats

IS 12553: 1988

MTD 26

Code of practice for design, construction, installation and operation of industrial gas/oil burning equipment

IS 12560: 1988

MTD 24 Code of practice for catholic protection of heat exchangers and condensers

IS 12938: 1990

MTD 17 Acceptance standards for radiographic inspection of steel castings

IS 13007: 1991

MTD 11 Tungsten electrodes for inert gas shielded arc welding and for plasma cutting and welding

IS 13177:1991

MTD 20 Passivation of stainless steel parts

IS 13417:1992

MTD 22 Code of practice for heat treatment of steels

IS 13805: 1993

MTD 21 General standard for qualification and certification of non-destructive testing personnel (Amendment 1)

IS 13851: 1993

MTD 11 Storage and redrying of covered electrodes before use – recommendations (Amendment 1)

IS 14191: 1996

MTD 24 Corrosion of metals and alloys – classifications of corrosivity of atmospheres

IS 14289: 1995

MTD 12 Manual tungsten inert-gas arc welding of nickel and nickel alloys – recommendations (second revision)

IS 14297: 1995

MTD 24 Corrosion of metals and alloys – determination of corrosion rate of standard specimens for the evaluation of corrosivity – methods of

IS 14321: MTD 24 Corrosion of metals and alloys – recommended values for

1995 the corrosivity categories of atmospheres IS14331:1996

MTD 16

Steels for high temperature bolting applications

IS 14492: 1997

MTD 26

Drying, pre-heating and commissioning of furnace installations, steam boilers, industrial kilns and chimneys – recommendations

*******