IS 8D Instruction - fd-rc.com · IS‐8D Instruction IS‐8D is a Do it Yourself ... During using,...

9
IS8D Instruction IS8D is a Do it Yourself system, that can be used to update any remote transmitter with PPM signal that does not have an independent module. IS8D includes from left to right: 1. 5p connector wire(connects transmitter main board to operation board) 2. Transmitter antenna (3db) 3. transmitter main board 1piece 4. LD Button Assembly 1 piece (include 2pcs button and 1pcs LED) 5. 3p wire ( white, red, black) Installation steps: 1. Turn on the transmitter ,make sure the position of operation board ,2.4G antenna ,transmit main board ; 2. Make sure the position of three wires on transmitter’s main board PPM/BAT/GND3. Fixed the operation board,2.4G antenna, transmit main board, Welding PPM /BAT/GND; Instruction: The operation of IS8D is the same as IS8F and IS8J. The only difference is the bind the button, range test button and three colors LED are on mounted permanently in the body of the transmitter rather than the module. The procedure for use is the same as the module version: bind first, set fail safe, test, and range test then use. Notice, will only need to bind and set failsafe one time. It will keep all binding information as well as fail safe programming until you decide to change it.

Transcript of IS 8D Instruction - fd-rc.com · IS‐8D Instruction IS‐8D is a Do it Yourself ... During using,...

Page 1: IS 8D Instruction - fd-rc.com · IS‐8D Instruction IS‐8D is a Do it Yourself ... During using, please test the negative pulse first, if the negative pulse doesn’t work normal

IS‐8D Instruction IS‐8D  is a Do  it Yourself system, that can be used to update any remote transmitter with PPM signal that does not have an independent module.  

IS‐8D includes from left to right: 1. 5p connector wire(connects transmitter main board to operation board) 2. Transmitter antenna (3db) 3. transmitter main board 1piece   4. LD Button Assembly 1 piece (include 2pcs button and 1pcs LED) 5. 3p wire ( white, red, black) 

           

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

   

    Installation steps:     

1. Turn on the transmitter ,make sure the position of operation board ,2.4G antenna ,transmit main board ; 

2. Make sure the position of three wires on transmitter’s main board  (PPM/BAT/GND) 3. Fixed the operation board,2.4G antenna, transmit main board, Welding PPM /BAT/GND;  

Instruction: 

The operation of IS‐8D is the same as IS‐8F and IS‐8J. The only difference is the bind the button, range test button and three colors LED are on mounted permanently  in the body of the transmitter rather than the module. The procedure for use  is the same as the module version: bind first, set fail safe, test, and range test then use. Notice, will only need to bind and set failsafe one time.    It will keep all binding information as well as fail safe programming until you decide to change it.   

 

Page 2: IS 8D Instruction - fd-rc.com · IS‐8D Instruction IS‐8D is a Do it Yourself ... During using, please test the negative pulse first, if the negative pulse doesn’t work normal

Notice:   1. You have to open the plastic case of radio, which may void your manufacturer warranty.   2. The DIY  system  is  installed  by  soldering  three wires  to  different  parts  of  the  transmitters:  BAT, 

ground(GND) and signal  (PPM). The voltage of  IS‐8D  is DC 6V~18V, you  located the power wire from  the back of  control  switch. The PPM  (signal wire)  is different  for each  radio. Attached are some  radios  and  their  location  of  the  3  wires.    If  you  are  unsure  of  the  location  for  these connections, please contact factory, dealer or reputable R/C technician. 

3. In  order  to  compatible  with  more  transmitters,  IS‐8D  has  the  switch  to  change  positive  and negative pulse. During using, please test the negative pulse first, if the negative pulse doesn’t work normal then change to positive pulse. Some JR radios require negative pulse. 

 

Possible location of the operation board reference: 

 

 

 

 

 

 

 

  

The position of main board fixed reference 

 

 

 

 

 

 

 

 

 

Page 3: IS 8D Instruction - fd-rc.com · IS‐8D Instruction IS‐8D is a Do it Yourself ... During using, please test the negative pulse first, if the negative pulse doesn’t work normal

Location of three wires   

 

 

 

 

 

 

 

 

 

 

 

 

Inside   

 

 

 

 

 

 

 

 

 

 

 

Page 4: IS 8D Instruction - fd-rc.com · IS‐8D Instruction IS‐8D is a Do it Yourself ... During using, please test the negative pulse first, if the negative pulse doesn’t work normal

Finished   

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Page 5: IS 8D Instruction - fd-rc.com · IS‐8D Instruction IS‐8D is a Do it Yourself ... During using, please test the negative pulse first, if the negative pulse doesn’t work normal

Three wires (PPM, BAT, GND) connection location for other radios.   

Installing of Futaba FF6S/T6XA,  it  is easy  to  lead PPM  from analog  (trainer) port, you can 

see the white one is PPM. 

 

 

 

 

 

 

 

 

 

 

Hitec Flash 4x  installation, you can see the yellow, red and black wire corresponding PPM, 

BAT & GND.         

 

 

   

 

 

 

Page 6: IS 8D Instruction - fd-rc.com · IS‐8D Instruction IS‐8D is a Do it Yourself ... During using, please test the negative pulse first, if the negative pulse doesn’t work normal

JR XF 421 installation, the below picture is the back of original RF board. The yellow, red and 

black wire corresponding PPM, BAT &GND.   

 

 

 

 

 

 

 

 

 

 

WFLY 6A(6C)  installation,  the  three wires of original high  frequency board  corresponding 

PPM, BAT &GND. 

 

 

 

 

 

 

 

 

 

 

Page 7: IS 8D Instruction - fd-rc.com · IS‐8D Instruction IS‐8D is a Do it Yourself ... During using, please test the negative pulse first, if the negative pulse doesn’t work normal

ESKY ET61: white,red black corresponding PPM, BAT &GND. 

 

 

 

 

 

 

 

 

 

 

 

Xinyi N‐8C: Getting PPM, BAT GND from analog port   

 

 

 

 

 

 

 

 

 

 

 

Page 8: IS 8D Instruction - fd-rc.com · IS‐8D Instruction IS‐8D is a Do it Yourself ... During using, please test the negative pulse first, if the negative pulse doesn’t work normal

GUANLI AM 4channel transmitter 

 

 

 

 

 

 

 

 

 

 

 

Remark: 

If you want to keep the original high frequency ports, and also want to update  it to 2.4G system, you can modify your transmitter to a duel frequency system.    It is as simple as adding a two‐way switch to change the BAT and PPM, check the pictures bellow:   

        

 

 

 

 

 

 

Page 9: IS 8D Instruction - fd-rc.com · IS‐8D Instruction IS‐8D is a Do it Yourself ... During using, please test the negative pulse first, if the negative pulse doesn’t work normal

Thanks: 

www.mx3g.com  、www.5imx.com  、www.5irc.com     

 

If  you  have  any  problems  during  the  installation  or  using,  please  contact 

Fly  Dream  or  dealers.    Please  do  not  hesitate  to  share  other  successful  In

stallations. We  are  also  glad  to  hear  your  valued  suggestion  and  opinions

  as we  strive  to  improve  our  items.  At  last,  enjoy  Fly  Dream! 

Fly  Dream   

May  14th,2010