IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
-
Upload
martinimartiini -
Category
Documents
-
view
315 -
download
6
Transcript of IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
1/355
Product manual (part 1 of 2), procedures
Articulated robot
IRB 6600 - 225/2.55 type A
IRB 6600 - 175/2.8 type A
IRB 6600 - 175/2.55 type A
IRB 6650 - 200/2.75 type A
IRB 6650 - 125/3.2 type A
M2000, M2004,M2000A
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
2/355
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
3/355
Product manual (part 1 of 2), procedures
IRB 6600 - 225/2.55 type A
IRB 6600 - 175/2.8 type A
IRB 6600 - 175/2.55 type A
IRB 6650 - 200/2.75 type A
IRB 6650 - 125/3.2 type A
M2000
M2000A
M2004
Document ID: 3HAC 020938-001
Revision: C
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
4/355
The information in this manual is subject to change without notice and should not be
construed as a commitment by ABB. ABB assumes no responsibility for any errors that
may appear in this manual.
Except as may be expressly stated anywhere in this manual, nothing herein shall be
construed as any kind of guarantee or warranty by ABB for losses, damages to persons
or property, fitness for a specific purpose or the like.
In no event shall ABB be liable for incidental or consequential damages arising fromuse of this manual and products described herein.
This manual and parts thereof must not be reproduced or copied without ABBs writtenpermission, and contents thereof must not be imparted to a third party nor be used forany unauthorized purpose. Contravention will be prosecuted.
Additional copies of this manual may be obtained from ABB at its then current charge.
Copyright 2004 ABB All right reserved.
ABB Automation Technologies ABRobotics
SE-721 68 Vsters
Sweden
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
5/355
Table of Contents
33HAC 020938-001 Revision: C
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Product documentation, M2000/M2000A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Product documentation, M2004 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
How to read the product manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1 Safety 15
1.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1.2 General safety information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
1.2.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
1.2.2 General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
1.2.2.1 Safety, service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
1.2.2.2 Limitation of Liability. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
1.2.2.3 Related information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
1.2.3 Safety risks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
1.2.3.1 Safety risks during service work on robot. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
1.2.3.2 Safety risks related to gripper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
1.2.3.3 Safety risks related to tools/workpieces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241.2.3.4 Safety risks related to pneumatic/hydraulic systems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
1.2.3.5 Safety risks during operational disturbances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
1.2.3.6 Safety risks during installation and service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
1.2.3.7 Risks associated with live electric parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
1.2.4 Safety actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
1.2.4.1 Safety fence dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
1.2.4.2 Fire extinguishing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
1.2.4.3 Emergency release of the robots arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
1.2.4.4 Brake testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
1.2.4.5 Risk of disabling function "Reduced speed 250 mm/s" . . . . . . . . . . . . . . . . . . . . . . . . . . 33
1.2.4.6 Safe use of the Teach Pendant Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
1.2.4.7 Work inside the manipulators working range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 351.3 Safety related instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
1.3.1 Safety signals, general . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
1.3.2 DANGER - Moving manipulators are potentially lethal! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
1.3.3 WARNING - The brake release buttons may be jammed after service work . . . . . . . . . . . . . . . . 39
1.3.4 WARNING - The unit is sensitive to ESD! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
1.3.5 WARNING - Safety risks during work with gearbox oil. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
1.3.6 WARNING - Mixed oils may cause severe damage to gearbox! . . . . . . . . . . . . . . . . . . . . . . . . . 43
2 Installation and commissioning 45
2.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
2.2 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
2.2.1 Pre-installation procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 462.2.2 Working range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
2.2.3 Risk of tipping / stability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
2.3 On-site installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
2.3.1 Lifting robot with fork lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
2.3.2 Lifting robot with roundslings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
2.3.3 Lifting robot with lifting slings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
2.3.4 Manually releasing the brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
2.3.5 Lifting the base plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
2.3.6 Securing the base plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
2.3.7 Orienting and securing the robot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
2.3.8 Fitting equipment on robot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
2.3.9 Installation of chip and dust protection (option) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 832.3.10 Loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
6/355
Table of Contents
3HAC 020938-001 Revision: C4
2.4 Restricting the working range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
2.4.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
2.4.2 Mechanically restricting the working range of axis 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
2.4.3 Mechanically restricting the working range of axis 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
2.4.4 Mechanically restricting the working range of axis 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 972.4.5 Position switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
2.5 Electrical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
2.5.1 Robot cabling and connection points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
3 Maintenance 107
3.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
3.2 Maintenance schedule and expected component life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
3.2.1 Specification of maintenance intervals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
3.2.2 Maintenance schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
3.2.3 Expected component life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
3.3 Inspection activities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1133.3.1 Inspection, oil level gearbox axis 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
3.3.2 Inspection, oil level gearbox axis 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
3.3.3 Inspection, oil level gearbox axis 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
3.3.4 Inspection, oil level gearbox axis 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
3.3.5 Inspection, oil level, gearbox axis 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
3.3.6 Inspection, oil level gearbox axis 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
3.3.7 Inspection, balancing device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
3.3.8 Inspection, cable harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
3.3.9 Inspection, information labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
3.3.10 Inspection, mechanical stop, axis 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
3.3.11 Inspection, additional mechanical stops. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
3.3.12 Inspection, damper axes 2-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
3.3.13 Inspection, position switch axes 1, 2 and 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
3.3.14 Inspection, signal lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
3.4 Replacement/changing activities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
3.4.1 Oil in gearboxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
3.4.2 Oil change, gearbox axis 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
3.4.3 Oil change, gearbox axis 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
3.4.4 Oil change, gearbox, axis 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
3.4.5 Oil change, gearbox, axis 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
3.4.6 Oil change, gearbox, axis 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
3.4.7 Oil change, gearbox axis 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
3.4.8 Replacement of SMB battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
3.5 Lubrication activities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
3.5.1 Lubrication, balancing device bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
3.6 Cleaning activities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
3.6.1 Cleaning, robot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
3.7 Service Information System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
3.7.1 Using the SIS system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
3.7.2 Description of Service Information System (SIS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
3.7.3 SIS system parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
3.7.4 Setting the SIS parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
3.7.5 Reading the SIS output logs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
3.7.6 Exporting the SIS data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
4 Repair 195
4.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
7/355
Table of Contents
53HAC 020938-001 Revision: C
4.2 General procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
4.2.1 Performing a leak-down test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
4.2.2 Mounting instructions for bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
4.2.3 Mounting instructions for seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198
4.3 Complete manipulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
4.3.1 Replacement of cable harness, axes 1-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
4.3.2 Replacement of cable harness, axes 5-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209
4.3.3 Replacement of complete arm system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215
4.4 Upper and lower arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221
4.4.1 Replacement of turning disk. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221
4.4.2 Replacement of complete wrist unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225
4.4.3 Replacement of upper arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231
4.4.4 Replacement of complete lower arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238
4.4.5 Replacement of lower arm shaft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246
4.4.6 Securing the lower arm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251
4.5 Frame and base. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255
4.5.1 Replacement of SMB unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255
4.5.2 Replacement of brake release unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258
4.5.3 Replacement of balancing device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263
4.5.4 Unloading the balancing device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271
4.5.5 Restoring the balancing device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275
4.6 Motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278
4.6.1 Replacement of motor, axis 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278
4.6.2 Replacement of motor axis 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282
4.6.3 Replacement of motor, axis 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288
4.6.4 Replacement of motor, axis 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294
4.6.5 Replacement of motor, axis 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299
4.6.6 Replacement of motor, axis 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 304
4.7 Gearboxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308
4.7.1 Replacement of gearbox, axis 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308
4.7.2 Replacement of gearbox axis 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 316
4.7.3 Replacement of gearbox, axis 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 324
4.7.4 Replacement of gearbox, axis 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330
5 Calibration information 337
5.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 337
5.2 Calibration methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338
5.3 Calibration scales and correct axis position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 340
5.4 Calibration movement directions for all axes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 341
5.5 Updating revolution counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 342
5.6 Checking the calibration position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 346
6 Decommissioning 349
6.1 Environmental information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350
6.2 Decommissioning of balancing device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 351
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
8/355
Table of Contents
3HAC 020938-001 Revision: C6
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
9/355
Overview
73HAC 020938-001 Revision: C
Overview
About this manual
This manual contains instructions for
mechanical and electrical installation of the manipulator
maintenance of the manipulator
mechanical and electrical repair of the manipulator.
Usage
This manual should be used during
installation, from lifting the manipulator to its work site and securing it to the
foundation to making it ready for operation
maintenance work repair work.
Who should read this manual?
This manual is intended for:
installation personnel
maintenance personnel
repair personnel.
Prerequisites
The reader should...
be a trained maintenance/repair craftsman
have the required knowledge of mechanical and electrical installation/repair/
maintenance work.
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
10/355
Overview
3HAC 020938-001 Revision: C8
Organization of chapters
The manual is organized in the following chapters:
Revisions
Chapter Contents
Safety Safety information
Installation and
commissioning
Information about installation of the manipulator.
Maintenance Information about maintenance work, including maintenanceschedules.
Repair Information about repair work.
Calibration Information Procedures that does not require specific calibrationequipment.
Decommissioning Environmental information about the manipulator.
Revision Description
- First edition.
Replaces previous manuals:
Installation and Commssioning Manual
Maintenance Manual
Repair Manual, part 1
Repair Manual, part 2.
Changes made in the material from the previous manuals:
Previous separate Removal and Refitting sections combined to oneReplacement section.
New spare part number for the balancing device, section Replacement ofbalancing deviceon page 263.
New spare part numbers for the motors, section Motorson page 278.
Updated instructions for calibration that describe the use of the Wylercalibration equipment, chapter Calibration informationon page 337.
Modified maintenance intervals for oil change and lubrication ofbalancing device bearing, section Maintenance scheduleon page 109.
Corrected information about the weight of the wrist unit, sectionReplacement of complete wrist uniton page 225.
More detailed instructions of how to use special tools when removing and
refitting the lower arm shaft, new section Replacement of lower arm shafton page 246.
More detailed information about how to use special tools when securingthe lower arm with a fixture, new section Securing the lower armon page
251.
Information about a cable protection at the lower arm, section Installationof position switch, axis 2on page 102.
Various corrections and editing made in text and figures due to technical
revisions, changes in the toolkits etc.
A Model M2004 implemented.
New spare part number for axis 6 motor.
Removed section Alternative calibration.
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
11/355
Overview
93HAC 020938-001 Revision: C
B Changes made in chapter Calibration:
Chapter Calibration is replaced with chapter Calibration information.
Chapter Safety, Service is replaced with a new Safety chapter.
C New lubricating oil in the gearboxes. Changes are made in the chapter:Maintenance.
Revision Description
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
12/355
Product documentation, M2000/M2000A
3HAC 020938-001 Revision: C10
Product documentation, M2000/M2000A
General
The complete product documentation kit for the M2000 robot system, including controller,
robot and any hardware option, consists of the manuals listed below:
Hardware manuals
All hardware, robots and controller cabinets, will be delivered with a Product manualwhich
is divided into two parts:
Product manual, procedures
Safety information
Installation and commissioning (descriptions of mechanical installation, electrical
connections and loading system software)
Maintenance (descriptions of all required preventive maintenance procedures
including intervals)
Repair (descriptions of all recommended repair procedures including spare parts)
Additional procedures, if any (calibration, decommissioning)
Product manual, reference information
Reference information (article numbers for documentation referred to in Product
manual, procedures, lists of tools, safety standards)
Part list
Foldouts or exploded views
Circuit diagrams
Software manuals
The software documentation consists of a wide range of manuals, ranging from manuals for
basic understanding of the operating system to manuals for entering parameters during
operation.
A complete listing of all available software manuals is available from ABB.
Controller hardware option manual
Each hardware option for the controller is supplied with its own documentation. Each
document set contains the types of information specified below:
Installation information
Repair information
Maintenance information
In addition, spare part information is supplied for the entire option.
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
13/355
Product documentation, M2004
113HAC 020938-001 Revision: C
Product documentation, M2004
General
The robot documentation may be divided into a number of categories. This listing is based on
the type of information contained within the documents, regardless of whether the products
are standard or optional. This means that any given delivery of robot products will not contain
alldocuments listed, only the ones pertaining to the equipment delivered.
However, all documents listed may be ordered from ABB. The documents listed are valid for
M2004 robot systems.
Hardware manuals
All hardware, robots and controller cabinets, will be delivered with a Product manualwhich
is divided into two parts:
Product manual, procedures
Safety information
Installation and commissioning (descriptions of mechanical installation, electrical
connections and loading system software)
Maintenance (descriptions of all required preventive maintenance procedures
including intervals)
Repair (descriptions of all recommended repair procedures including spare parts)
Additional procedures, if any (calibration, decommissioning)
Product manual, reference information
Reference information (article numbers for documentation referred to in Productmanual, procedures, lists of tools, safety standards)
Part list
Foldouts or exploded views
Circuit diagrams
RobotWare manuals
The following manuals describe the robot software in general and contain relevant reference
information:
RAPID Overview: An overview of the RAPID programming language.
RAPID reference manual part 1: Description of all RAPID instructions.
RAPID reference manual part 2: Description of all RAPID functions and data types.
Technical reference manual - System parameters: Description of system
parameters and configuration workflows.
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
14/355
Product documentation, M2004
3HAC 020938-001 Revision: C12
Application manuals
Specific applications (e.g. software or hardware options) are described in Application
manuals. An application manual can describe one or several applications.
An application manual generally contains information about:
The purpose of the application (what it does and when it is useful)
What is included (e.g. cables, I/O boards, RAPID instructions, system parameters)
How to use the application
Examples of how to use the application
Operators manuals
This group of manuals is aimed at those having first hand operational contact with the robot,
i.e. production cell operators, programmers and trouble shooters. The group of manuals
include: Operators manual - IRC5 with FlexPendant
Operators manual - RobotStudio Online
Trouble shooting manualfor the controller and robot
Miscellaneous
A number of manuals provide generic descriptions of the robot and robot system. These
include:
Robot fundamentals(describing the fundamental aspects, functions, concept and
similar, of a robot system to provide a basic understanding of the robot system)
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
15/355
How to read the product manual
133HAC 020938-001 Revision: C
How to read the product manual
Reading the procedures
The procedures contain references to figures, tools, material etc. The references are read as
described below.
References to figures
The procedures often include references to components or attachment points located on the
robot/controller. The components or attachment points are marked with italic textin the
procedures and completed with a reference to the figure where the current component or
attachment point is shown.
The denomination in the procedure for the component or attachment point corresponds to the
denomination in the referenced figure.
The table below shows an example of a reference to a figure from a step in an procedure.
References to required equipment
The procedures often include references to equipment (spare parts, tools etc.) required for the
different actions in the procedure. The equipment is marked with italic textin the procedures
and completed with a reference to the section where the equipment is listed with further
information, i.e. article number, dimension.
The denomination in the procedure for the component or attachment point corresponds to the
denomination in the referenced list.
The table below shows an example of a reference to a list of required equipment, from a step
in an procedure.
Safety information
The manual includes a separate safety chapter that must be read through before proceeding
with any service or installation procedures. All procedures also include specific safety
information when dangerous steps are to be performed. Read more in chapter Safetyon page
15.
Step Action Note/Illustration
8. Remove the rear attachment screws, gearbox. Shown in the figure Location ofgearbox on page xx.
Step Action Note/Illustration
3. Fit a new sealing, axis 2to the gearbox. Art. no. is specified in Requiredequipment on page xx.
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
16/355
How to read the product manual
3HAC 020938-001 Revision: C14
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
17/355
1 Safety
1.1. Introduction
153HAC 020938-001 Revision: C
1 Safety
1.1. Introduction
Overview
The safety information in this manual is divided in two categories:
general safety aspects, important to attend to before performing any service work on
the robot. These are applicable for all service work and are found in section General
safety informationon page 16.
specific safety information, pointed out in the procedure at the moment of the danger.
How to avoid and eliminate the danger is either detailed directly in the procedure, or
further detailed in separate instructions, found in section Safety related instructionson
page 36.
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
18/355
1 Safety
1.2.1. Introduction
3HAC 020938-001 Revision: C16
1.2 General safety information
1.2.1. Introduction
Definitions
This section details general safety information for service personnel i.e. personnel performing
installation, repair and maintenance work.
Sections
The general safety information is divided into the following sections:
1. General information contains lists of:
Safety, service
Limitation of liability
Referenced documents
2. Safety risks lists dangers relevant when servicing the robot system. The dangers are split
into different categories:
Safety risks during service work on robot
Safety risks related to gripper/end effector
Safety risks related to tools/workpieces
Safety risks related to pneumatic/hydraulic systems
Safety risks during operational disturbances
Safety risks during installation and service
Risks associated with live electric parts
3. Safety actions details actions which may be taken to remedy or avoid dangers.
Safety fence dimensions
Fire extinguishing
Emergency release of the manipulators arm
Brake testing
Risk of disabling function "Reduced speed 250 mm/s"
Safe use of the Teach Pendant Unit enabling device
Work inside the manipulators working range Signal lamp (optional)
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
19/355
1 Safety
1.2.2.1. Safety, service
173HAC 020938-001 Revision: C
1.2.2. General information
1.2.2.1. Safety, service
Validity and responsibility
The information does not cover how to design, install and operate a complete system, nor
does it cover all peripheral equipment, which can influence the safety of the total system. To
protect personnel, the complete system must be designed and installed in accordance with the
safety requirements set forth in the standards and regulations of the country where the robot
is installed.
The users of ABB industrial robots are responsible for ensuring that the applicable safety laws
and regulations in the country concerned are observed and that the safety devices necessary
to protect people working with the robot system have been designed and installed correctly.
Personnel working with robots must be familiar with the operation and handling of theindustrial robot, described in the applicable documents, e.g. Users Guide and Product
Manual.
Connection of external safety devices
Apart from the built-in safety functions, the robot is also supplied with an interface for the
connection of external safety devices. Via this interface, an external safety function can
interact with other machines and peripheral equipment. This means that control signals can
act on safety signals received from the peripheral equipment as well as from the robot.
In the Product Manual - Installation and Commissioning, instructions are provided for
connecting safety devices between the robot and the peripheral equipment.
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
20/355
1 Safety
1.2.2.2. Limitation of Liability
3HAC 020938-001 Revision: C18
1.2.2.2. Limitation of Liability
General
Any information given in this manual regarding safety, must not be construed as a warranty
by ABB that the industrial robot will not cause injury or damage even if all safety instructions
have been complied with.
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
21/355
1 Safety
1.2.2.3. Related information
193HAC 020938-001 Revision: C
1.2.2.3. Related information
General
The list below specifies documents which contain useful information:
Documents
Type of information Detailed in document Section
Installation of safety devices Product manual for the
manipulator
Installation and commissioning
Changing robot modes Users Guide Start-up
Restricting the working space Product manual for themanipulator
Installation and commissioning
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
22/355
1 Safety
1.2.3.1. Safety risks during service work on robot
3HAC 020938-001 Revision: C20
1.2.3. Safety risks
1.2.3.1. Safety risks during service work on robot
Overview
This section includes information of general safety risks to be considered when performing
service work on the robot.
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
23/355
1 Safety
1.2.3.1. Safety risks during service work on robot
213HAC 020938-001 Revision: C
Complete robot
Cabling
Gearboxes and motors
Safety risk Description
Hot components!
Caution!
Motors and gears are HOT after running the robot!
Touching the motors and gears may result in burns!
Removed parts may result in
collapse of robot!
Warning!
Take any necessary measures to ensure that the robotdoes not collapse as parts are removed, e.g. secure thelower arm with fixtures if removing motor, axis 2.
Safety risk Description
Cable packs are sensitive to
mechanical damage!
Caution!
The cable packs are sensitive to mechanical damage!They must be handled with care, especially theconnectors, in order to avoid damaging them!
Safety risk Description
Gears may be damaged if
excessive force is used!
Caution!
Whenever parting/mating motor and gearbox, the gearsmay be damaged if excessive force is used!
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
24/355
1 Safety
1.2.3.1. Safety risks during service work on robot
3HAC 020938-001 Revision: C22
Balancing device
Safety risk Description
Dangerous balancing device!
Warning!
Do not under any circumstances, deal with the balancing
device in any other way than that detailed in the productdocumentation! For example, attempting to open thebalancing device is potentially lethal!
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
25/355
1 Safety
1.2.3.2. Safety risks related to gripper
233HAC 020938-001 Revision: C
1.2.3.2. Safety risks related to gripper
CAUTION!
Ensure that a gripper is prevented from dropping a workpiece, if such is used.
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
26/355
1 Safety
1.2.3.3. Safety risks related to tools/workpieces
3HAC 020938-001 Revision: C24
1.2.3.3. Safety risks related to tools/workpieces
Safe handling
It must be possible to turn off tools, such as milling cutters, etc., safely. Make sure that guards
remain closed until the cutters stop rotating.
It should be possible to release parts by manual operation (valves).
Safe design
Grippers/end effectors must be designed so that they retain workpieces in the event of a power
failure or a disturbance of the controller.
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
27/355
1 Safety
1.2.3.4. Safety risks related to pneumatic/hydraulic systems
253HAC 020938-001 Revision: C
1.2.3.4. Safety risks related to pneumatic/hydraulic systems
General
Special safety regulations apply to pneumatic and hydraulic systems.
Residual energy
Residual energy may be present in these systems so, after shutdown, particular care
must be taken.
The pressure in pneumatic and hydraulic systems must be released before starting to
repair them.
Safe design
Gravity may cause any parts or objects held by these systems to drop.
Dump valves should be used in case of emergency.
Shot bolts should be used to prevent tools, etc., from falling due to gravity.
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
28/355
1 Safety
1.2.3.5. Safety risks during operational disturbances
3HAC 020938-001 Revision: C26
1.2.3.5. Safety risks during operational disturbances
General
The industrial robot is a flexible tool which can be used in many different industrial
applications.
All work must be carried out professionally and in accordance with the applicable
safety regulations.
Care must be taken at all times.
Qualified personnel
Remedial action must only be carried out by qualified personnel who are familiar with
the entire installation as well as the special risks associated with its different parts.
Extraordinary risksIf the working process is interrupted, extra care must be taken due to risks other than those
associated with regular operation. Such an interruption may have to be rectified manually.
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
29/355
1 Safety
1.2.3.6. Safety risks during installation and service
273HAC 020938-001 Revision: C
1.2.3.6. Safety risks during installation and service
General risks during installation and service
The instructions in the Product Manual - Installation and Commissioning must always
be followed.
Emergency stop buttons must be positioned in easily accessible places so that the robot
can be stopped quickly.
Those in charge of operations must make sure that safety instructions are available for
the installation in question.
Those who install the robot must have the appropriate training for the robot system in
question and in any safety matters associated with it.
Nation/region specific regulations
To prevent injuries and damage during the installation of the robot system, the regulations
applicable in the country concerned and the instructions of ABB Robotics must be complied
with.
Non-voltage related risks
Safety zones, which have to be crossed before admittance, must be set up in front of
the robot's working space. Light beams or sensitive mats are suitable devices.
Turntables or the like should be used to keep the operator out of the robot's working
space.
The axes are affected by the force of gravity when the brakes are released. In addition
to the risk of being hit by moving robot parts, you run the risk of being crushed by the
parallel arm.
Energy, stored in the robot for the purpose of counterbalancing certain axes, may be
released if the robot, or parts thereof, is dismantled.
When dismantling/assembling mechanical units, watch out for falling objects.
Be aware of stored heat energy in the controller.
Never use the robot as a ladder, i.e. do not climb on the robot motors or other part
during service work. There is a serious risk of slipping because of the high temperature
of the motors or oil spills that can occur on the robot.
To be observed by the supplier of the complete system
The supplier of the complete system must ensure that all circuits used in the safety
function are interlocked in accordance with the applicable standards for that function.
The supplier of the complete system must ensure that all circuits used in the
emergency stop function are interlocked in a safe manner, in accordance with the
applicable standards for the emergency stop function.
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
30/355
1 Safety
1.2.3.7. Risks associated with live electric parts
3HAC 020938-001 Revision: C28
1.2.3.7. Risks associated with live electric parts
Voltage related risks, general
Although troubleshooting may, on occasion, have to be carried out while the power
supply is turned on, the robot must be turned off (by setting the mains switch to OFF)
when repairing faults, disconnecting electric leads and disconnecting or connecting
units.
The mains supply to the robot must be connected in such a way that it can be turned
off outside the robot's working space.
Voltage related risks, controller
A danger of high voltage is associated with the following parts:
Be aware of stored electrical energy (DC link) in the controller.
Units inside the controller, e.g. I/O modules, can be supplied with power from an
external source.
The mains supply/mains switch
The power unit
The power supply unit for the computer system (230 VAC)
The rectifier unit (400-480 VAC and 700 VDC. Note: Capacitors!)
The drive unit (700 VDC)
The service outlets (115/230 VAC)
The power supply unit for tools, or special power supply units for the machining
process
The external voltage connected to the control cabinet remains live even when the robot
is disconnected from the mains.
Additional connections
Voltage related risks, robot
A danger of high voltage is associated with the robot in:
The power supply for the motors (up to 800 VDC)
The user connections for tools or other parts of the installation (max. 230 VAC, see
Installation and Commissioning Manual)
Voltage related risks, tools, material handling devices, etc
Tools, material handling devices, etc., may be live even if the robot system is in the OFF
position. Power supply cables which are in motion during the working process may be
damaged.
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
31/355
1 Safety
1.2.4.1. Safety fence dimensions
293HAC 020938-001 Revision: C
1.2.4. Safety actions
1.2.4.1. Safety fence dimensions
General
Install a safety cell around the robot to ensure safe robot installation and operation.
Dimensioning
Dimension the fence or enclosure to enable it to withstand the force created if the load being
handled by the robot is dropped or released at maximum speed. Determine the maximum
speed from the maximum velocities of the robot axes and from the position at which the robot
is working in the work cell (see Product Specification - Description, Robot Motion).
Also consider the maximum possible impact caused by a breaking or malfunctioning rotating
tool or other device fitted to the manipulator.
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
32/355
1 Safety
1.2.4.2. Fire extinguishing
3HAC 020938-001 Revision: C30
1.2.4.2. Fire extinguishing
NOTE!
Use a CARBON DIOXIDE (CO2) extinguisher in the event of a fire in the robot (manipulatoror controller)!
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
33/355
1 Safety
1.2.4.3. Emergency release of the robots arm
313HAC 020938-001 Revision: C
1.2.4.3. Emergency release of the robots arm
Description
In an emergency situation, any of the robots axes may be released manually by pushing the
brake release buttons on the robot or on an optional external brake release unit.
How to release the brakes is detailed in section:
Manually releasing the brakeson page 67.
The robot arm may be moved manually on smaller robot models, but larger models may
require using an overhead crane or similar.
Increased injury
Before releasing the brakes, make sure that the weight of the arms does not increase the
pressure on the trapped person, further increasing any injury!
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
34/355
1 Safety
1.2.4.4. Brake testing
3HAC 020938-001 Revision: C32
1.2.4.4. Brake testing
When to test
During operation the holding brakes of each axis motor wear normally. A test may be
performed to determine whether the brake can still perform its function.
How to test
The function of each axis motor holding brakes may be checked as detailed below:
1. Run each manipulator axis to a position where the combined weight of the manipulator
arm and any load is maximized (max. static load).
2. Switch the motor to the MOTORS OFF position with the Operating mode selector on the
controller.
3. Check that the axis maintains its position.
If the manipulator does not change position as the motors are switched off, then the brake
function is adequate.
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
35/355
1 Safety
1.2.4.5. Risk of disabling function "Reduced speed 250 mm/s"
333HAC 020938-001 Revision: C
1.2.4.5. Risk of disabling function "Reduced speed 250 mm/s"
NOTE!
Do not change "Transm gear ratio" or other kinematic parameters from the Teach PendantUnit or a PC. This will affect the safety function Reduced speed 250 mm/s.
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
36/355
1 Safety
1.2.4.6. Safe use of the Teach Pendant Unit
3HAC 020938-001 Revision: C34
1.2.4.6. Safe use of the Teach Pendant Unit
NOTE!
The enabling device is a push button located on the side of the Teach Pendant Unit (TPU)which, when pressed halfway in, takes the system to MOTORS ON. When the enabling
device is released or pushed all the way in, the robot is taken to the MOTORS OFF state.
To ensure safe use of the Teach Pendant Unit, the following must be implemented:
The enabling device must never be rendered inoperative in any way.
During programming and testing, the enabling device must be released as soon as
there is no need for the robot to move.
The programmer must always bring the Teach Pendant Unit with him/her, when
entering the robot's working space. This is to prevent anyone else taking control over
the robot without the programmer knowing.
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
37/355
1 Safety
1.2.4.7. Work inside the manipulators working range
353HAC 020938-001 Revision: C
1.2.4.7. Work inside the manipulators working range
WARNING!
If work must be carried out within the robots work envelope, the following points must beobserved:
The operating mode selector on the controller must be in the manual mode position to
render the enabling device operative and to block operation from a computer link or
remote control panel.
The robot's speed is limited to max. 250 mm/s when the operating mode selector is in
position < 250 mm/s. This should be the normal position when entering the working
space. The position 100% "full speed" may only be used by trained personnel who are
aware of the risks that this entails.
Pay attention to the rotating axes of the manipulator! Keep a distance to the axes in
order not to get entangled with hair or clothing. Also be aware of any danger that maybe caused by rotating tools or other devices mounted on the manipulator or inside the
cell.
Test the motor brake on each axis, according to sectionBrake testingon page 32.
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
38/355
1 Safety
1.3.1. Safety signals, general
3HAC 020938-001 Revision: C36
1.3 Safety related instructions
1.3.1. Safety signals, general
General
This section specifies all dangers that may arise from performing the work detailed in the
manual. Each danger is detailed in its own section consisting of:
A caption specifying the danger level (DANGER, WARNING or CAUTION) and the
type of danger.
A brief description of what will happen if the operator/service personnel does not
eliminate the danger.
An instruction of how to eliminate the danger to facilitate performing the activity at
hand.
Danger levels
The table below defines the captions specifying the danger levels used throughout this
manual.
Symbol Designation Signification
danger
DANGER Warns that an accident willoccur if the instructions
are not followed, resulting in a serious or fatal injuryand/or severe damage to the product. It applies towarnings that apply to danger with, for example,
contact with high voltage electrical units, explosionor fire risk, risk of poisonous gases, risk of crushing,impact, fall from height etc.
warning
WARNING Warns that an accident mayoccur if the instructions
are not followed, that can lead to serious injury,possibly fatal, and/or great damage to the product. Itapplies to warnings that apply to danger with, for
example, contact with high voltage electrical units,
explosion or fire risk, risk of poisonous gases, risk ofcrushing, impact, fall from height etc.
Electrical shock
ELECTRICAL
SHOCK
The electrocution or electrical shock symbol
indicates electrical hazards which could result insevere personal injury or death.
caution
CAUTION Warns that an accident may occur if the instructions
are not followed, that can result in injury and/ordamage to the product. It also applies to warnings ofrisks that include burns, eye injury, skin injury,
hearing damage, crushing or slipping, tripping,
impact, fall from height etc. Furthermore, it applies towarnings that include function requirements whenfitting and removing equipment, where there is a risk
of damaging the product or causing a breakdown.
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
39/355
1 Safety
1.3.1. Safety signals, general
373HAC 020938-001 Revision: C
Electrostatic discharge(ESD)
ELECTROSTATICDISCHARGE (ESD)
The electrostatic discharge (ESD) symbol indicateselectrostatic hazards which could result in severe
damage to the product.
Note
NOTE Note symbols alert you to important facts and
conditions.
Tip
TIP Tip symbols direct you to specific instructions, whereto find additional information or how to perform a
certain operation in an easier way.
Symbol Designation Signification
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
40/355
1 Safety
1.3.2. DANGER - Moving manipulators are potentially lethal!
3HAC 020938-001 Revision: C38
1.3.2. DANGER - Moving manipulators are potentially lethal!
Description
Any moving manipulator is a potentially lethal machine.
When running the manipulator, it may perform unexpected and sometimes irrational
movements. However, all movements are performed with great force and may seriously
injure any personnel and/or damage any piece of equipment located within the manipulator
working range.
Elimination
Step Action Info/Illustration
1. Before attempting to run the manipulator,
make sure all emergency stop equipmenthas been correctly installed and connected.
Emergency stop equipment such as
gates, tread mats, light curtains, etc.
2. If possible, use the hold-to-run buttonwhenever possible.
The hold-to-run button is used in manualmode, not in automatic mode.
How to use the hold-to-run control inRobotWare 5.0 is detailed in sectionHow to use the hold-to-run switchinthe Operators Manual, IRC5.
How to use the hold-to-run control inRobotWare 4.0 is detailed in sectionThe Teach Pendant unitin the Users
Guide.
3. Make sure no personnel is present within
the manipulator working range beforepressing the start button.
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
41/355
1 Safety
1.3.3. WARNING - The brake release buttons may be jammed after service work
393HAC 020938-001 Revision: C
1.3.3. WARNING - The brake release buttons may be jammed after service work
Description
The brake release unit has push buttons for brake release of each axis motor. When service
work is performed inside the SMB recess that includes removal and refitting of the brake
release unit, the brake release buttons may be jammed after refitting!
In case the power is turned on while a brake release button is jammed in depressed position,
the affected motor brake is released! This may cause serious personal injuries and damage to
the robot!
Elimination
To eliminate the danger after service work has been performed inside the SMB recess, follow
the procedure below:
Step Action
1. Make sure the power is turned off.
2. Remove the push button guard, if necessary.
3. Check the push buttons of the brake release unit by pressing them down, one byone.
Make sure none of the buttons are jammed in the tube.
4. If a button gets jammed in the depressed position, the alignment of the brake release
unit must be adjusted so that the buttons can move freely in their tubes!
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
42/355
1 Safety
1.3.4. WARNING - The unit is sensitive to ESD!
3HAC 020938-001 Revision: C40
1.3.4. WARNING - The unit is sensitive to ESD!
Description
ESD (electro static discharge) is the transfer of electrical static charge between two bodies at
different potentials, either through direct contact or through an induced electrical field. When
handling parts or their containers, personnel not connected to ground potential may transfer
high static charges. This discharge may destroy sensitive electronics.
Elimination
Step Action Note/Illustration
1. Use a wrist strap Wrist straps must be tested frequently toensure that they are not damaged and areoperating correctly.
2. Use an ESD protective floor mat. The mat must be grounded through a current-limiting resistor.
3. Use a dissipative table mat. The mat should provide a controlled dischargeof static voltages and must be grounded.
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
43/355
1 Safety
1.3.5. WARNING - Safety risks during work with gearbox oil
413HAC 020938-001 Revision: C
1.3.5. WARNING - Safety risks during work with gearbox oil
Description
When handling the gearbox oil, there are several dangers to both personal injuries and product
damages! Following safety information must be regarded before performing any work with
the oil in the gearboxes!
Warnings and elimination
Warning Description Elimination / Action
-
Hot oil!
Changing and draininggearbox oil may require
handling hot oil of up to 90 C!
Make sure that protective gearlike goggles and gloves are
always worn during this activity.
-
Possible pressure build
up in gearbox!
When opening the oil plug,
there may be pressure presentin the gearbox, causing oil tospray from the opening!
Open oil plug carefully and keep
away from the opening. Do notoverfill the gearbox when filling.
-
Do not overfill!
Overfilling of gearbox oil can
lead to internal over-pressureinside the gearbox which in
turn may:
damage seals and
gaskets
completely press outseals and gaskets
prevent the manipulatorfrom moving freely.
Make sure not to overfill the
gearbox when filling with oil!After filling, check the correct oillevel.
-
Do not mix types of oil!
Mixing types of oil may causesevere damage to thegearbox!
When filling gearbox oil, do notmix different types of oil unlessspecified in the instruction.
Always use the type of oil
specified by the manufacturer!
-
Heat up the oil!
Warm oil drains quicker thancold oil.
When changing gearbox oil, firstrun the robot for a time to heatup the oil.
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
44/355
1 Safety
1.3.5. WARNING - Safety risks during work with gearbox oil
3HAC 020938-001 Revision: C42
-
Specified amount
depends on drained
volume!
The specified amount of oil isbased on the total volume of
the gearbox. When changingthe oil, the amount of refilled oilmay differ from the specified
amount, depending on howmuch oil has previously beendrained from the gearbox.
After refilling, check the oil level.
Warning Description Elimination / Action
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
45/355
1 Safety
1.3.6. WARNING - Mixed oils may cause severe damage to gearbox!
433HAC 020938-001 Revision: C
1.3.6. WARNING - Mixed oils may cause severe damage to gearbox!
Description
The six gearboxes of the robot are historically filled with different types of oil. When refilling
a gearbox it is extremely important to fill with exactly the same type of oil that is currently
used! In case the gearbox oil is contaminated with an other type of oil, the gearbox may be
severely damaged and must therefor be rinsed.
Shell Tivela S 150 mixed with Optimol Optigear RMO 150
The procedure below details how to rinse the contaminated gearbox if the oil types Shell
Tivela S 150 and Optimol Optigear RMO 150 are mixed.
Shell Tivela S 150 mixed with Mobil Gearlube X320
The procedure below details how to rinse the contaminated gearbox if the oil types Shell
Tivela S 150 and Mobil Gearlube X320 are mixed.
Step Action Note
1. Flush the gearbox properly three times with the correct typeof oil. Use a service program when flushing.
2. Refill the gearbox with the correct type of oil.
Step Action Note
1. If the gearbox should contain Tivela S 150 and is
contaminated with Gearlube X320:
Flush the gearbox properly three times with Tivela S150. Use a service program when flushing.
Refill the gearbox with Tivela S 150.
2. If the gearbox should contain Gearlube X320 and iscontaminated with Tivela S 150:
Drain the gearbox.
Flush the gearbox once with Gearlube X320. Use a
serviceprogram when flushing.
Drain the gearbox properly! It is important to allow allthe oil be drained from the gearbox!
Refill the gearbox with Gearlube X320.
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
46/355
1 Safety
1.3.6. WARNING - Mixed oils may cause severe damage to gearbox!
3HAC 020938-001 Revision: C44
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
47/355
2 Installation and commissioning
2.1. Introduction
453HAC 020938-001 Revision: C
2 Installation and commissioning
2.1. Introduction
General
This chapter contains information for installing the robot to the working site.
More detailed technical data, such as load diagram, permitted extra loads (equipment) and
location of extra loads (equipment), may be found in the Product Specification for the robot.
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
48/355
2 Installation and commissioning
2.2.1. Pre-installation procedure
3HAC 020938-001 Revision: C46
2.2 Unpacking
2.2.1. Pre-installation procedure
General
This section is intended for use when unpacking and installing the robot for the first time. It
also contains information useful during later re-installation of the robot.
Checking the pre-requisites for installation
The checklist below details what must be observed before proceeding with the actual
installation of the robot:
1. Make sure only qualified installation personnel conforming to all national and local codes
are allowed to perform the installation.
2. Visually inspect the robot to make sure it is not damaged.
3. Make sure the lifting device used is suitable to handle the weight of the robot as specified
in Weight, roboton page 46.
4. If the robot is not installed directly, it must be stored as described in Storage conditions,
roboton page 47.
5. Make sure the expected operating environment of the robot conforms to the specifications
as described in Operating conditions, roboton page 47.
6. Before taking the robot to its installation site, make sure the site conforms toLoads on
foundation, roboton page 47,Requirements on foundation, roboton page 47and
Protection classes, roboton page 48.
7. Before moving the robot, please observeRisk of tipping / stabilityon page 53regarding
risk of tipping!
8. When these prerequisites are met, the robot may be taken to its installation site as
described in section On-site installationon page 54.
Weight, robot
The table below shows the weights of the different models:
Robot model Weight
IRB 6600 - 175/2.55 1700 kg
IRB 6600 - 225/2.55 1700 kg
IRB 6600 - 175/2.8 1700 kg
IRB 6650 - 125/3.2 1725 kg
IRB 6650 - 200/2.75 1700 kg
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
49/355
2 Installation and commissioning
2.2.1. Pre-installation procedure
473HAC 020938-001 Revision: C
Loads on foundation, robot
The table below shows the various forces and torques working on the robot during different
kinds of operation.
Note!These forces and torques are extreme values that are rarely encountered during
operation. The values also never reach their maximum simultaneously!
Requirements on foundation, robot
The table below shows the requirements for the foundation where the robot is installed:
Storage conditions, robot
The table below shows the allowed storage conditions for the robot:
Operating conditions, robot
The table below shows the allowed operating conditions for the robot:
Force Endurance load (operation) Max. load (emergency stop)
Force xy 10.1 kN 20.7 kN
Force z 18.0 13.8 kN 18.0 22.4 kN
Torque xy 27.6 kNm 50.6 kNm
Torque z 7.4 kNm 14.4 kNm
Requirement Value Note
Min. levelity 0.5 mm
Max. tilt 5 The limit for the maximum load on the robotis reduced if the robot is tilted.
Contact ABB for further information about
acceptable loads.
Min. resonance frequency 22 Hz
Parameter Value
Min. ambient temperature -25 C
Max. ambient temperature +55C
Max. ambient temperature (less than 24 hrs) +70C
Max. ambient humidity Max. 95% at constant temperature
Parameter Value
Min. ambient temperature +5 C
Max. ambient temperature +50C
Max. ambient humidity Max. 95% at constant temperature
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
50/355
2 Installation and commissioning
2.2.1. Pre-installation procedure
3HAC 020938-001 Revision: C48
Protection classes, robot
The table below shows the protection class of the robot:
Equipment Protection class
robot IP 67
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
51/355
2 Installation and commissioning
2.2.2. Working range
493HAC 020938-001 Revision: C
2.2.2. Working range
Working range
This section details the working ranges of the manipulator models.
IRB 6600 - 175/2.55 and IRB 6600 - 225/2.55
The illustration below shows the unrestricted working range of IRB 6600 - 175/2.55 and IRB
6600 - 225/2.55:
xx0200000025
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
52/355
2 Installation and commissioning
2.2.2. Working range
3HAC 020938-001 Revision: C50
IRB 6600 - 175/2.8
The illustration below shows the unrestricted working range of IRB 6600 - 175/2.8:
xx0200000026
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
53/355
2 Installation and commissioning
2.2.2. Working range
513HAC 020938-001 Revision: C
IRB 6650 - 125/3.2
The illustration below shows the unrestricted working range of IRB 6650 - 125/3.2:
xx0200000338
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
54/355
2 Installation and commissioning
2.2.2. Working range
3HAC 020938-001 Revision: C52
IRB 6650 - 200/2.75
The illustration below shows the unrestricted working range of IRB 6650 - 200/2.75:
xx0200000339
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
55/355
2 Installation and commissioning
2.2.3. Risk of tipping / stability
533HAC 020938-001 Revision: C
2.2.3. Risk of tipping / stability
Risk of tipping
When the robot is not fastened to the foundation and standing still, the robot is not stable in
the whole working area. Moving the arms will displace the center of gravity, which may cause
the robot to tip over. Do notchange the robot position before securing it to the foundation.
Stabililty
The figure below shows the robot in its shipping position, which also is its most stable
position.
xx0100000103
WARNING!
The robot is likely to be mechanically unstable while not secured to the foundation!
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
56/355
2 Installation and commissioning
2.3.1. Lifting robot with fork lift
3HAC 020938-001 Revision: C54
2.3 On-site installation
2.3.1. Lifting robot with fork lift
General
The robot may be moved using a fork lift, provided that available special aids are used.
This section describes how to attach the fork lift equipment to the robot.
Different designs
There are two different versions of the fork lift that fit one design of the frame respectevily.
The different designs of the frame and of the fork lift attachments are shown in the figure
below. Determine which fork lift set fits the current robot.
Note!The distance between the attachment holes for the fork lift pockets, shown in the figure
below, are different depending on the design of the frame. This means that the fork lift sets
are unique for one type of frame and not compatible!
Except for the shorter distance between the attachment holes, the later design of the frame
also includes an extra oil plug, located as shown in the figure below.
xx0200000386
1 Frame version withoutan oil plug, use the fork lift set: 3HAC 0604-2
2 Frame version withan oil plug (C), use the fork lift set: 3HAC 0604-1
A Attachment holes, fork lift 3HAC 0604-2
B Attachment holes, fork lift 3HAC 0604-1
C Oil plug
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
57/355
2 Installation and commissioning
2.3.1. Lifting robot with fork lift
553HAC 020938-001 Revision: C
Attachment points
The attachment points for the fork lift equipment are shown in the figure below.
xx0400000707
Required equipment
To determine which fork lift set to use, see the sectionDifferent designson page 54.
A Attachment points, spacer and horizontal attachment screws
B Attachment points, horizontal attachment screws
C Attachment points, vertical attachment screws
D Attachment points, horizontal attachment screws
Equipment, etc. Art. no. Note
Fork lift set, incl. all requiredhardware
3HAC 0604-2 See the figure Fork lift set, 3HAC 0604-2on page 56.
Fork lift set, incl. all requiredhardware
3HAC 0604-1 See the figure Fork lift set, 3HAC 0604-1on page 57.
Standard toolkit 3HAC 1557-1 The contents are defined in section
Standard toolkitin the Product manual,reference information!
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
58/355
2 Installation and commissioning
2.3.1. Lifting robot with fork lift
3HAC 020938-001 Revision: C56
Fork lift set, 3HAC 0604-2
The fork lift set, 3HAC 0604-2, is fitted to the robot as shown in the figure below.
xx0100000102
A Vertical attachment screws (4 pcs / fork lift pocket)
B Fork lift pockets (2 pcs)
C Spacer (2 pcs)
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
59/355
2 Installation and commissioning
2.3.1. Lifting robot with fork lift
573HAC 020938-001 Revision: C
Fork lift set, 3HAC 0604-1
The fork lift set, 3HAC 0604-1, is fitted to the robot as shown in the figure below.
xx0200000379
A Fork lift pocket (2 pcs, different from each other)
B Spacer (2 pcs)
C Horizontal attachment screws (4 pcs / fork li ft pocket)
D Vertical attachment screws (2 pcs)
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
60/355
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
61/355
2 Installation and commissioning
2.3.1. Lifting robot with fork lift
593HAC 020938-001 Revision: C
5. Secure the longer fork lift pocketto thespacers with four of the horizontal
attachment screwsand washers.Note!The vertically and the horizontallyattached screws are identical, buttightened with different torques!
Make sure the original screws arealways used (or replacements of
equivalent quality: M16, quality 12.9)!Attachment points on the robot areshown in the figure Attachment pointson page 55.
xx0400001068
A: horizontal attachment
screws, 4 pcs, M16 x 60.Tightening torque: 60 Nm.
B: spacers, 2 pcs.
6. Make sure the securing screw is removed
from the fork lift pocket!
It is only used for robot model IRB 6650S.
xx0400000977
A: securing screw
Step Action Info/Illustration
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
62/355
2 Installation and commissioning
2.3.1. Lifting robot with fork lift
3HAC 020938-001 Revision: C60
7. Secure the fork lift pocket to the robot withthe two vertical attachment screwsand
washers.(only valid for the fork lift set 3HAC 0604-1)
Note!The vertically and the horizontally
attached screws are identical, buttightened with different torques!
xx0300000464
A: vertical attachment screws, 2
pcs, M16x60; tightening torque:270 Nm.
Make sure the original screws arealways used (or replacements of
equivalent quality: M16, quality 12.9)!
Attachment points on the robot are
shown in the figure Attachment pointson page 55.
8.
Caution!
Caution!The fork lift pocket weighs 22 kg!
9. Secure the shorter fork lift pocket on the
other side of the robot with the fourremaining horizontal attachment screws.
4 pcs, M16x60; tightening torque: 60
Nm.
Make sure the original screws are
always used (or replacements ofequivalent quality: M16, quality 12.9)!
Attachment points on the robot are
shown in the figure Attachment pointson page 55.
10. Double-check that the pockets are
properly secured to the robot! Insert the
fork lift forks into the pockets.
xx0200000380
Reposition the harness, if any, before
using a fork lift!
Step Action Info/Illustration
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
63/355
2 Installation and commissioning
2.3.1. Lifting robot with fork lift
613HAC 020938-001 Revision: C
11.
Caution!
Caution!
The robot weighs 1725 kg! All lifting
equipment used must be dimensionedaccordingly!
12. Carefully lift the robot and move it to itsinstallation site.
13.
Warning!
WARNING!
Personnel must not, under any
circumstances, be present under thesuspended load!
Step Action Info/Illustration
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
64/355
2 Installation and commissioning
2.3.2. Lifting robot with roundslings
3HAC 020938-001 Revision: C62
2.3.2. Lifting robot with roundslings
General
The robot may be lifted with roundslings according to the illustration below. The illustration
is identical with the label attached to the robots lower arm.
Attachment points
The figure below shows how to attach the roundslings to the robot.
xx0200000282
A Chain sling with shortener
B Roundsling, manipulator
C Roundsling, upper arm Note!Do not stretch!
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
65/355
2 Installation and commissioning
2.3.2. Lifting robot with roundslings
633HAC 020938-001 Revision: C
Sling specification
Lifting with roundslings
Sling type Qty Lifting capacity Length / NoteChain sling with shortener 3 pcs 4 250 kg 0.47 m
0.54 m
0.76 m
Roundsling, manipulator 3 pcs 2 000 kg 2 m
Roundsling, upper arm 2 pcs 2 000 kg Note!Do not stretch!
Step Action Note
1. Attach the roundslings to the robot according to thefigure Attachment pointson page 62.
2.
Caution!
Caution!
The robot weighs 1725 kg! All lifting equipment used
must be dimensioned accordingly!
3.
Warning!
WARNING!
Personnel must not, under any circumstances, be
present under the suspended load!
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
66/355
2 Installation and commissioning
2.3.3. Lifting robot with lifting slings
3HAC 020938-001 Revision: C64
2.3.3. Lifting robot with lifting slings
General
This section contains a general overview of how to lift the complete robot using special lifting
equipment. More detailed instructions are included with the equipment.
Illustration, lifting slings
The figure below shows how to lift the complete robot with lifting slings.
Note the recommended robot position shown in the figure below and in the instruction!
Attempting to lift a robot in any other position may result in the robot tipping over, causing
severe damage or injury!
xx0200000153
A Load hook
B Swivelling lifting eyes, 4 pcs
C Shortening hook
D Chain
E M12 lifting eye
F Lifting devices eye
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
67/355
2 Installation and commissioning
2.3.3. Lifting robot with lifting slings
653HAC 020938-001 Revision: C
Required equipment
Slings attached directly onto robot
The section below details how to lift and move the robot using lifting slings when these are
attached directly onto the robot frame.
I Lifting slings, 4 pcs
L Hook
Equipment Art. no. Note
Lifting device, manipulator 3HAC 15607-1 Includes
user instructions (3HAC 15971-2).
Step Action Note
1. Run the overhead crane to a position
above the robot.
2. Make sure the robot is positioned as
shown in the figure on the right. If it isnot, position it that way.
Release the brakes if required as detailed
in section Manually releasing the brakeson page 67.
xx0100000103
3. Fit the lifting device, manipulator to the
robot as described in the enclosedinstruction!
Art. no. is specified in Required
equipmenton page 65!
4.
Caution!
Caution!
The robot weighs 1725 kg! All liftingequipment used must be dimensioned
accordingly!
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
68/355
2 Installation and commissioning
2.3.3. Lifting robot with lifting slings
3HAC 020938-001 Revision: C66
5.
Warning!
WARNING!
Personnel must not, under anycircumstances, be present under the
suspended load!
6. Raise the overhead crane to lift the
robot.
Make sure all hooks and attachments
maintain their correct positions whilelifting the robot!
Always move the robot at very lowspeeds, making sure it does not tip.
Step Action Note
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
69/355
2 Installation and commissioning
2.3.4. Manually releasing the brakes
673HAC 020938-001 Revision: C
2.3.4. Manually releasing the brakes
General
This section details how to release the holding brakes of each axis motor.
Location of brake release unit
The internal brake release unit is located at the frame, as shown in the figure below.
xx0300000044
Releasing the brakes
The procedure below details how to release the holding brakes when the robot is equipped
with an internal brake release unit.
- Internal brake release unit with push buttons
Step Action Info/Illustration
1. The internal brake release unit is equipped with sixbuttons for controlling the axes brakes. The buttons arenumbered according to the numbers of the axes.
If the robot is not connected to the controller, power mustbe supplied to the connector R1.MP according to sectionSupplying power to connector R1.MPon page 68.
The buttons are shownin the figure Location ofbrake release uniton
page 67
2.
-
Danger!
When releasing the holding brakes, the robot axes maymove very quickly and sometimes in unexpected ways!Make sure no personnel is near the robot arm!
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
70/355
2 Installation and commissioning
2.3.4. Manually releasing the brakes
3HAC 020938-001 Revision: C68
Supplying power to connector R1.MP
If the robot is not connected to the controller, power must be supplied to connector R1.MP in
the robot base in order to enable the brake release buttons on the robot.
3. Release the holding brake on a particular robot axis bypressing the corresponding button on the internal brake
release panel and keeping it depressed.The brake will function again as soon as the button isreleased.
Step Action Info/Illustration
Step Action Note/Illustration
1.
-
Danger!
Incorrect connections, such as
supplying power to the wrong pin, maycause all brakes to be releasedsimultaneously!
2. Supply 0V on pin 12 and 24V on pin11.
xx0300000565
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
71/355
2 Installation and commissioning
2.3.5. Lifting the base plate
693HAC 020938-001 Revision: C
2.3.5. Lifting the base plate
General
This section details how to lift the base plate
Hole configuration
xx0200000096
Lifting the base plate
Equipment Art. no. Note
Lifting eye, M16 3HAC 14457-4 3 pcs
Lifting slings 3 pcs
Length: approx. 2 m
A Attachment holes for lifting eyes (x3)
Step Action Info/Illustration
1.
-
Caution!
The base plate weighs 353 kg! All lifting equipment
used must be dimensioned accordingly!
2. Fit the lifting eyes in the three lifting holes. Shown in the figure Holeconfigurationon page 69!
3. Fit the lifting slings to the eyes and to the liftingdevice.
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
72/355
2 Installation and commissioning
2.3.6. Securing the base plate
3HAC 020938-001 Revision: C70
2.3.6. Securing the base plate
General
This section details how to secure the base plate.
Base plate, dimensions
xx0100000105
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
73/355
2 Installation and commissioning
2.3.6. Securing the base plate
713HAC 020938-001 Revision: C
xx0400000715
Note1 Four holes for alternative clamping
-
8/9/2019 IRC5-IRB6600 Prod Man 3HAC020938-001 Procedures RevC En
74/355
2 Installation and commissioning
2.3.6. Securing the base plate
3HAC 020938-001 Revision: C72
Base plate, grooves and holes
The