iPhone 6 Plus Display Assembly Replacementodrepairservices.com/wp/PDF/iPhone6PlusFDA.pdfiPhone 6...

iPhone6PlusFullDisplayAssemblyReplacement

WerxParts www.werxparts.com Page1of14

iPhone 6 Plus Full Display Assembly

Replacement INTRODUCTION Use this guide along with the Werx Repair Mat to replace the cracked or broken screen on your iPhone 6 Plus. Follow Werx Repair Mat Steps 1,2,4 to disassemble. Reverse steps for re-assembly. Use this guide to strip and replace your iPhone 6 Plus front panel. It will show you how to remove the home button, front-facing camera and sensor assembly, LCD shield plate, and home button ribbon cable. TOOLS: IMPORTANT Take your time! The repair takes about 15-30 minutes.

Remember that you will be handling fragile parts, so be gentle!

Most screws are different sizes so keep them organized.

Werx Repair Mat



Step 1: Pentalobe Screws

• Before disassembling your iPhone, be

sure it is powered off.

• Remove the two 3.6 mm Pentalobe

screws next to the lightning connector.

Step 2: Front Panel Assembly

• While holding the iPhone down with

one hand, insert a plastic opening tool

and begin gently pry the rear case

down, away from the display assembly.



Step 3:

• Pull the home button end of the front

panel assembly away from the rear

case, using the top of the phone as a

hinge.

Keep the front panel supported at a 90

degree angle in relation to the rear

case.

Step 4:

• Use the Werx Repair Mat to keep

screws organized and prevent screw

misplacement damage

• Remove the following five Phillips

screws securing the front panel

assembly cable bracket:

o Three 1.2 mm Phillips screws

o One 1.7 mm Phillips screw

o One 3.1 Phillips screw



Step 5:

• Remove the front panel assembly cable

bracket from the logic board.

Step 6:

• Using a plastic opening tool disconnect

the front-facing camera and sensor

cable connector.



Step 7:


the home button cable connector.

Step 8:


the digitizer cable connector.



Step 9:

• Finally, using a plastic opening tool

disconnect the display data cable

connector.

• Remove the front panel assembly from

the rear case.

Step 10: Home Button

• Remove the two 1.8 mm Phillips

screws securing the home button

bracket.



Step 11:

• Remove the home button bracket from

the front panel.

Step 12:

• Remove one 1.7 mm Phillips screws

securing the LCD shield plate to the

front panel



Step 13:

• Using the plastic opening tool

disconnect the home button cable

connector by pushing it up and away

from the home button.

Step 14:

• Use the plastic opening tool to carefully

separate the home button cable from

the adhesive securing it to the front

panel.



Step 15:

• Once all the adhesive has been

separated, remove the home button

from the front panel.

Step 16: Home Button

• Insert the home button to the front

panel.



Step 17:

• Connect the home button cable

connector.

Step 18:

• Insert the home button bracket from the

front panel.



Step 19:

• Insert the two Phillips screws securing

the home button bracket.

Step 20:

• Insert the LCD assembly to the rear

case.

• Connect the following flex cable to the

logic board:

o Display data cable

o Digitizer cable

o Home button cable

o Front-facing camera and censor

cable



Step 21:

• Insert the front panel assembly cable

bracket to the logic board.

Step 22:

• Insert five Phillips screws to securing

the front panel assembly cable bracket.



Step 23:

• Align the clips just below the top edge

of the rear case. Then, slide the front

panel upward until its top edge is flush

with the rear case.

Step 24:

• Run your fingers along the sides being

sure the assembly slips evenly into the

frame.



Step 25: Pentalobe Screws

• Insert the two Pentalobe screws next to

the lightning connector.

iPhone 6 Plus Display Assembly Replacementodrepairservices.com/wp/PDF/iPhone6PlusFDA.pdfiPhone 6...

Documents

Transcript of iPhone 6 Plus Display Assembly Replacementodrepairservices.com/wp/PDF/iPhone6PlusFDA.pdfiPhone 6...