Introduction to RS485 Author: Zhu Tao Date: 2008-10-24.
-
Upload
muriel-ramsey -
Category
Documents
-
view
226 -
download
0
Transcript of Introduction to RS485 Author: Zhu Tao Date: 2008-10-24.
Introduction to RS485Introduction to RS485
Author: Zhu TaoAuthor: Zhu Tao
Date: 2008-10-24Date: 2008-10-24
OutlineOutline
OverviewOverview
FeaturesFeatures
ComparisonComparison
EvaluationEvaluation
ConclusionConclusion
BibliographyBibliography
OutlineOutline
OverviewOverview
FeaturesFeatures
ComparisonComparison
EvaluationEvaluation
ConclusionConclusion
BibliographyBibliography
OverviewOverview
DefinitionDefinition[1][1]
RS485, namely EIA-485, is an electrical RS485, namely EIA-485, is an electrical specification of a specification of a two-wiretwo-wire, , half-duplexhalf-duplex, , multipointmultipoint serial communicationserial communication channel. channel.
supporting transmission in two directions sim
ultaneouslyThe transmission of data in both directions, but only one direction at a time.
Refers to a communications line (net
work) that provides a path from one location to many.
the process of sending data one bit at one time, sequentially, over a communication channel or comput
er bus.
OverviewOverview
Use a differential balanced line over Use a differential balanced line over twisted pairtwisted pair
Can span a large distance (up to 1200 m)Can span a large distance (up to 1200 m)
Linear topologyLinear topology is the preferred is the preferred recommended wires arrangementrecommended wires arrangement
Not star or ring topology, because of
signal reflection or excessively low or high termination
impedance.
RS485 topology
OutlineOutline
OverviewOverview
FeaturesFeatures
ComparisonComparison
EvaluationEvaluation
ConclusionConclusion
BibliographyBibliography
OutlineOutline
OverviewOverview
FeaturesFeatures
ComparisonComparison
EvaluationEvaluation
ConclusionConclusion
BibliographyBibliography
FeaturesFeatures
Often use the master-slave arrangementOften use the master-slave arrangement
Not specify or recommend any data Not specify or recommend any data protocol (i.e. the overlaying protocol)protocol (i.e. the overlaying protocol)
Can be extended to Can be extended to full-duplexfull-duplex using 4- using 4-wirewire
Components cost very lowComponents cost very low
NO integral method to detect data collision NO integral method to detect data collision (often be implemented using software)(often be implemented using software)
A full-duplex (or rarely double-duplex) system allows communication in both directions, and unlike half-duplex, allows this to happen simultaneousl
y.
OutlineOutline
OverviewOverview
FeaturesFeatures
ComparisonComparison
EvaluationEvaluation
ConclusionConclusion
BibliographyBibliography
OutlineOutline
OverviewOverview
FeaturesFeatures
ComparisonComparison
EvaluationEvaluation
ConclusionConclusion
BibliographyBibliography
ComparisonComparison
摘自摘自 [3][3]
OutlineOutline
OverviewOverview
FeaturesFeatures
ComparisonComparison
EvaluationEvaluation
ConclusionConclusion
BibliographyBibliography
OutlineOutline
OverviewOverview
FeaturesFeatures
ComparisonComparison
EvaluationEvaluation
ConclusionConclusion
BibliographyBibliography
EvaluationEvaluation
AdvantagesAdvantages
DisadvantagesDisadvantages
EvaluationEvaluation
AdvantagesAdvantages[2][2]
1.1. Small overhead (without defining the Small overhead (without defining the overlaying protocol, fault detect, etc.)overlaying protocol, fault detect, etc.)
2.2. Cheaper hardwareCheaper hardware3.3. Maximum data transmission speed is Maximum data transmission speed is
10Mbps10Mbps4.4. Has good noise immunityHas good noise immunity5.5. Maximum 256 transceivers are allowed Maximum 256 transceivers are allowed
to connect to the busto connect to the bus
EvaluationEvaluation
DisadvantagesDisadvantages[2][2]
1.1. Only one node can transmit data to the bus at Only one node can transmit data to the bus at any one moment and all other nodes must be any one moment and all other nodes must be in receiving status, otherwise the transmission in receiving status, otherwise the transmission will fail (when 2 or more nodes transmit data will fail (when 2 or more nodes transmit data simultaneously).simultaneously).
2.2. A special communication cable is needed. A special communication cable is needed. And the maximum communication distance And the maximum communication distance depends on the type of the cable.depends on the type of the cable.
3.3. Need software to ensure no over 2 nodes Need software to ensure no over 2 nodes transmit data simultaneously. transmit data simultaneously.
EvaluationEvaluation
Click Click herehere to see the detail to see the detail
OutlineOutline
OverviewOverview
FeaturesFeatures
ComparisonComparison
EvaluationEvaluation
ConclusionConclusion
BibliographyBibliography
OutlineOutline
OverviewOverview
FeaturesFeatures
ComparisonComparison
EvaluationEvaluation
ConclusionConclusion
BibliographyBibliography
ConclusionConclusion
RS485RS485 is used as the electrical layer for is used as the electrical layer for many well known interface standards, many well known interface standards, including Profibus and Modbus. Therefore including Profibus and Modbus. Therefore RS485RS485 will be in use for many years in the will be in use for many years in the future. future.
And in the TCN area, the train control And in the TCN area, the train control system can be abstracted to a master-system can be abstracted to a master-slaves model. So RS485 can be used.slaves model. So RS485 can be used.
OutlineOutline
OverviewOverview
FeaturesFeatures
ComparisonComparison
EvaluationEvaluation
ConclusionConclusion
BibliographyBibliography
OutlineOutline
OverviewOverview
FeaturesFeatures
ComparisonComparison
EvaluationEvaluation
ConclusionConclusion
BibliographyBibliography
BibliographyBibliography
1.1. http://en.wikipedia.org/wiki/EIA-485http://en.wikipedia.org/wiki/EIA-485
2.2. http://www.metering.com/node/12618http://www.metering.com/node/12618
3.3. http://www.lammertbies.nl/comm/info/RS-485.hhttp://www.lammertbies.nl/comm/info/RS-485.htmltml
4.4. 基于基于 RS485 RS485 的的 25T 25T 客车电源串行通信系统客车电源串行通信系统 .pd.pdff
5.5. 422 and 485 Standards Overview.pdf422 and 485 Standards Overview.pdf
6.6. The Art and Science of RS-485.pdfThe Art and Science of RS-485.pdf
7.7. EIA TIA-485-A an Overview.pdfEIA TIA-485-A an Overview.pdf
More can be seen in the next week.More can be seen in the next week.
Thanks a lot!Thanks a lot!