Introducing the InterCooler Type3

Our new InterCooler Type3 is designed to exceed the performance and versatility of all previous driver comfort systems available. We’ve employed the newest manufacturing methods and the most advanced technology heat sinks and thermal materials to yield a lightweight solid state electronic cooling system with uncompromised performance and reliability. At 730 BTU/hr the Type3 offers better than a 45% increase in cooling performance over our previous Type2 model, without increased weight. Installation is easier with inlet and outlet for the driver’s air now both located on the top of the unit, reducing the required mounting and clearance space. Heat removal from the unit now utilizes our Uber3 high performance blower technology which more easily overcomes duct airflow restrictions and gives better cooling under caution flag driving and during pit stops.

The redesigned controller is smaller, lighter and simple to operate. It offers more comfort level selections, 4 airflow and 4 cooling power settings. Power is now run directly to the main A/C unit allowing for easier placement of the controller.

The Type3 system ships complete with: InterCooler Type3 helmet air conditioner Controller with 4 DualLoc fastener strips Pig tail to connect to car harness 4 CamLoc studs and receptacles 2 1-1/4” ID driver’s air hoses with adapter ends Clean-out tool (to clean condensation drains) 2 replacement inlet filters Installation guide

InCarSS Filtration System In August 2013 we will offer our new InCarSS carbon monoxide and VOC filtration package. It is an

add-on that can be fully integrated into the Type3 InterCooler. It is a piggy back system with no external hose, wiring or separate mounting required. Several configurations of carbon monoxide and road race filter cartridge variations are available.

Performance Specifications Part number - IC32001 Power Requirements

12 to 16 VDC 32 Amps (initial surge)

Typical Operation (72°F (22.2°C), std. atmospheric pressure)

Voltage - 13.8 VDC Current - 28.5 Amps Airflow to helmet (max.) - 26.3 cfm (12.5 l/sec) Outflow pressure to helmet (max.) - 13.5 in.-H2O (3.36 kpa)

Typical performance at highest cooling power setting (4)

Airflow setting Flow cfm (l/sec) Delta T°F (°C) Load current (amps)

1 18 (8.5) 34 (18.9) 24.4

2 20 (9.4) 31 (17.2) 25.3

3 23.5 (11.1) 28 (15.6) 26.7

4 26.3 (12.5) 26 (14.4) 28.5 (Data was taken at 75°F ambient and 35% relative humidity powered at 13.8VDC)

Overload Protection Current overload protection - internal self resetting 40 amp circuit breaker Self resetting - after 30 second delay Blowers - current limited to 15 amps, restart after 5 seconds

Physical Overall dimensions - 18.5” (47cm) x 5.9” (15cm) x 5.2” (13.2cm) Power lead wire - 18” (45 cm) Power pig tail - 48” (150 cm) Control input wire - 18” (45 cm) Controller wire - 48” (122 cm) Weight - 7 lb- 5 oz (3.3 Kg) with controller

Quick performance and physical comparisons to previous model InterCoolers

Parameter Type1 Type2 Type3

Voltage 13.8 13.8 13.8

Current (amps) 17 20 28.5

Power consumption (watts) 235 276 394

Airflow (cfm) 15 21 26.3

Delta T (F)* 19 22 25.7

Cooling power (BTU/hr) 307 499 730

Cooling performance improvement over Type 1 --- 62% 137%

Cooling performance improvement over Type 2 --- --- 46%

Weight (lbs)** 5.75 7.25 7.3

Length (in) 15 16 18.5

Width (in) 4 4.75 4.75

Height (in) 4.5 3.5 3.5

*Delta T measured at highest blower setting, lower settings yield even colder air temps **includes controller and mounting hardware