IntEGRAL HoRSEPoWER PRoDuCt CAtALoG · 86 20.3 1.5 1050 1.3 786 1328 rx42-0020-hsb2s-x...
Transcript of IntEGRAL HoRSEPoWER PRoDuCt CAtALoG · 86 20.3 1.5 1050 1.3 786 1328 rx42-0020-hsb2s-x...
Aluminum and Stainless Steel Gearmotors and Reducers
Integral horsepower product catalog
XSERIES
SSERIES
QSERIES
· More power: from 1/4 to 5HP
· Versatile mounting and configuration options
· Available in worm or high efficiency hypoid gearing
· Custom options available
· Perfect for industrial machinery, conveying and larger format applications
Rev. 10.17
Removeable Inspection CoverAllows periodic inspection of gearing during routine maintenance.
Single-Piece AluminumCombines light weight with high tensile strength. Precision machined for alignment of bearings and gearing.
Co
ntE
ntS XSERIES
High Efficiency Hypoid Speed Reducer
XSER
IESPowerStAR X 1 - 2
PowerSTAR X42 3 - 40.33 - 2HP, 562 - 1328 in-lbs, 22.6 - 240RPM
PowerSTAR X43 5 - 60.25 - 0.75HP, 1328 - 1416 in-lbs, 5.4 - 34.8RPM
PowerSTAR X52 7 - 80.5 - 5HP, 1195 - 2213 in-lbs, 23.4 - 290RPM
PowerSTAR X53 9 - 100.25 - 1HP, 2213 in-lbs, 3.0 - 30.8RPM
PowerSTAR X62 11 - 120.5 - 5HP, 2124 - 3629 in-lbs, 23.4 - 290RPM
PowerSTAR X63 13 - 140.25 - 1.5HP, 3629 in-lbs, 3.0 - 30.8RPM
PowerSTAR X Technical Info 15 - 16PowerSTAR X Selection Table 17 - 18
Q Series 19 - 20
Q45 21 - 220.25 - 1HP, 257 - 345 in-lbs, 17.2 - 250RPM
Q50 23 - 240.25 - 2HP, 434 - 611 in-lbs, 17.5 - 250RPM
Q63 25 - 260.25 - 2HP, 1000 - 1230 in-lbs, 18.6 - 250RPM
Q85 27 - 280.5 - 5HP, 2036 - 2921 in-lbs, 18.2 - 250RPM
Q Series Technical Info 29 - 30Q Series Selection Table 31 - 32
S Series 33 - 34
S45 35 - 360.25 - 1HP, 248 - 345 in-lbs, 17.2 - 250RPM
S50 37 - 380.25 - 2HP, 434 - 611 in-lbs, 17.5 - 250RPM
S63 39 - 400.25 - 2HP, 1000 - 1230 in-lbs, 18.6 - 250RPM
S85 41 - 420.5 - 5HP, 2036 - 2921 in-lbs, 18.2 - 250RPM
S Series Technical Info 43 - 44S Series Selection Table 45 - 46
Motors
General Purpose, Three Phase 47General Purpose, Single Phase 48Brake Motors, Three Phase 49 - 50 IEC AC Motors, Three Phase 51 - 52
GearsHardened and ground gears.
Alloy HousingIs vacuum impregnated (MIL-STD 276) for protection and sealing. No secondary finish required but readily accepts paint.
FlangeFully modular to NEMA or IEC standard sizes.Ratios
Available in 2 stage and 3 stage combinations for a wide range of ratio options
2
100% Factory Pressure Leak tested
X42High Efficiency Hypoid Speed Reducer0.33 - 2HP, 562 - 1328 in-lbs, 22.6 - 240RPM
· All hardened and ground gears for high efficiency and quiet operation · Interchangeability with most global manufacturers
tECHnICAL DAtAX42
output Speed (RPM)
Ratio Motor Power (HP)
output torque (in-lbs)
Service Factor
oHL nom. torque (in-lbs)
Reducer Part number*
Gearmotor Part number*
240 7.32 504 1.7
562 841 RX42-0007-HSB2S-XGX42-0007-HSB2S-XAG3B
1 252 3.3 GX42-0007-HSB2S-XAE3B
156 11.22 774 1.7
562 1328 RX42-0011-HSB2S-XGX42-0011-HSB2S-XAG3B
1 387 3.4 GX42-0011-HSB2S-XAE3B
133 13.22 911 1.5
674 1328 RX42-0013-HSB2S-XGX42-0013-HSB2S-XAG3B
1 456 2.9 GX42-0013-HSB2S-XAE3B
115 15.32 1056 1.3
674 1328 RX42-0015-HSB2S-XGX42-0015-HSB2S-XAG3B
1 528 2.5 GX42-0015-HSB2S-XAE3B
98 17.92 1240 1.1
786 1328 RX42-0018-HSB2S-XGX42-0018-HSB2S-XAG3B
1 620 2.1 GX42-0018-HSB2S-XAE3B
86 20.31.5 1050 1.3
786 1328 RX42-0020-HSB2S-XGX42-0020-HSB2S-XAF3B
1 700 1.9 GX42-0020-HSB2S-XAE3B
82 21.41.5 1110 1.2
786 1328 RX42-0021-HSB2S-XGX42-0021-HSB2S-XAF3B
1 740 1.8 GX42-0021-HSB2S-XAE3B
75 23.51.5 1217 1.1
899 1328 RX42-0023-HSB2S-XGX42-0023-HSB2S-XAF3B
1 812 1.6 GX42-0023-HSB2S-XAE3B
64 27.61.5 1429 0.9
899 1328 RX42-0028-HSB2S-XGX42-0028-HSB2S-XAF3B
1 953 1.4 GX42-0028-HSB2S-XAE3B
60 29.21 1010 1.3
899 1328 RX42-0029-HSB2S-XGX42-0029-HSB2S-XAE3B
0.5 505 2.6 GX42-0029-HSB2S-WAC3B
53 32.91 1137 1.2
899 1328 RX42-0033-HSB2S-XGX42-0033-HSB2S-XAE3B
0.5 569 2.3 GX42-0033-HSB2S-WAC3B
45.9 38.11 1318 1
1079 1328 RX42-0038-HSB2S-XGX42-0038-HSB2S-XAE3B
0.5 659 2 GX42-0038-HSB2S-WAC3B
39.0 44.90.75 1164 1.1
1079 1328 RX42-0045-HSB2S-WGX42-0045-HSB2S-WAD3B
0.5 776 1.7 GX42-0045-HSB2S-WAC3B
34.8 50.30.75 1305 0.9
1079 1159 RX42-0050-HSB2S-WGX42-0050-HSB2S-WAD3B
0.5 870 1.3 GX42-0050-HSB2S-WAC3B
29.9 58.60.75 1519 0.9
1079 1328 RX42-0059-HSB2S-WGX42-0059-HSB2S-WAD3B
0.5 1013 1.3 GX42-0059-HSB2S-WAC3B
22.6 77.40.5 1337 1
1079 1328 RX42-0077-HSB2S-WGX42-0077-HSB2S-WAC3B
0.33 883 1.5 GX42-0077-HSB2S-WAB3B
Notes: All units shown are standard configuration. Input motor, output shaft and mounting options are available. Motor Specification: 230/460 VAC 60/50Hz, 3PH 1800 RPM Nom. - inverter duty *NEMA Input Sizes: W = 56CX = 143/5TCY = 182/4TC Motors 1HP and greater meet EISA efficiency requirements.
3
X42
Output FlangeMounting
Torque Arm
Output Flange Output Flange
Output Shaft Insert
3.93
7
1.476
ø0.3
741.
969
ø0.3741.969
3.9372.953
- 0.0
014
- 0.0
028
1.240 4.331
ø4.3
31
3.406 6.299
0.1180.394 0.354
5.118
0.1380.433
1.240 4.331
0.4333.406 7.874
ø5.1
18
6.496
- 0.0
017
- 0.0
033
- 0.0
017
- 0.0
033
8.465
0.157
0.512
1.240 4.331
0.4333.406 9.843
ø7.0
87
0
- 0.0
013
4.331
ø1.0
00
5/16-18
0.250
1.11
0
6.618
2.1302.287x 0.83
4
F2SB
tA R/L
F4F3
DRAWInGSBasic Gearbox
Hollow Shaft B C D
Imperial 1.000” 1.118” 0.250”
Metric (mm) 25 28.3 8
X42 Nema Flanges øF A
56C-143/5TC 6.5” 8.228”
IEC Flanges øF (mm) A (mm)
71 B5 160 197.5
80/90 B5 200 199.5
71 B14 105 197.5
80 B14 120 199.5
90 B14 140 199.52.75
6 5.78
7
Mounting holesposition
2.7564.331
ø3.1
50
3.9374 holes M8x0.472
0.85
8
1.988 0.118
- 0.0
012
- 0.0
024
StandardHollow shaft
+0.0008 0
øFA
D
C
B
ø433
4.6460.787
4.25
2
1.96
9
1.18
1
5.827 17.2pounds
Gearbox Weight
X43High Efficiency Hypoid Speed Reducer0.25 - 0.75HP, 1328 - 1416 in-lbs, 5.4 - 34.8RPM
· All hardened and ground gears for high efficiency and quiet operation · Interchangeability with most global manufacturers
X43output Speed (RPM)
Ratio Motor Power (HP)
output torque (in-lbs)
Service Factor
oHL nom. torque (in-lbs)
Reducer Part number**
Gearmotor Part number**
34.8 50.40.75 1278 1
1079 1328 RX43-0050-HSB2S-WGX43-0050-HSB2S-WAD3B
0.5 852 1.6 GX43-0050-HSB2S-WAC3B
31.7 55.20.75 1402 0.9
1079 1328 RX43-0055-HSB2S-WGX43-0055-HSB2S-WAD3B
0.5 935 1.4 GX43-0055-HSB2S-WAC3B
29.2 59.90.75 1521 0.9
1079 1328 RX43-0060-HSB2S-WGX43-0060-HSB2S-WAD3B
0.5 1014 1.3 GX43-0060-HSB2S-WAC3B
26.6 65.70.5 1112 1.2
1079 1328 RX43-0066-HSB2S-WGX43-0066-HSB2S-WAC3B
0.25 556 2.4 GX43-0066-HSB2S-WAA3B
24.4 71.80.5 1215 1.1
1079 1328 RX43-0072-HSB2S-WGX43-0072-HSB2S-WAC3B
0.25 608 2.2 GX43-0072-HSB2S-WAA3B
22.0 79.40.5 1345 1
1079 1328 RX43-0079-HSB2S-WGX43-0079-HSB2S-WAC3B
0.25 672 2 GX43-0079-HSB2S-WAA3B
19.0 92.10.33 1029 1.3
1079 1328 RX43-0092-HSB2S-WGX43-0092-HSB2S-WAB3B
0.25 779 1.7 GX43-0092-HSB2S-WAA3B
18.4 95.00.33 1062 1.3
1079 1328 RX43-0095-HSB2S-WGX43-0095-HSB2S-WAB3B
0.25 804 1.7 GX43-0095-HSB2S-WAA3B
13.8 126.60.33 1414 1
1079 1416 RX43-0127-HSB2S-WGX43-0127-HSB2S-WAB3B
0.25 1071 1.3 GX43-0127-HSB2S-WAA3B
13.1 133.20.33 1488 1
1079 1416 RX43-0133-HSB2S-WGX43-0133-HSB2S-WAB3B
0.25 1127 1.3 GX43-0133-HSB2S-WAA3B
11.7 150.20.33 1678 0.8
1079 1416 RX43-0150-HSB2S-WGX43-0150-HSB2S-WAB3B
0.25 1271 1.1 GX43-0150-HSB2S-WAA3B
9.9 177.3 0.25 1501 0.9 1079 1416 RX43-0177-HSB2S-W GX43-0177-HSB2S-WAA3B
8.3 210.4 0.25* 1781 0.8 1079 1416 RX43-0210-HSB2S-W GX43-0210-HSB2S-WAA3B
7.6 230.8 0.25* 1953 0.7 1079 1416 RX43-0231-HSB2S-W GX43-0231-HSB2S-WAA3B
6.4 272.5 0.25* 2306 0.6 1079 1416 RX43-0272-HSB2S-W GX43-0272-HSB2S-WAA3B
5.4 323.4 0.25* 2737 0.5 1079 1416 RX43-0323-HSB2S-W GX43-0323-HSB2S-WAA3B
Notes: All units shown are standard configuration. Input motor, output shaft and mounting options are available. *Power greater than that which can be supported by the gearbox for continuous duty.
Motor Specification: 230/460 VAC 60/50Hz, 3PH 1800 RPM Nom. - inverter duty *NEMA Input Sizes: W = 56CX = 143/5TCY = 182/4TC Motors 1HP and greater meet EISA efficiency requirements.
5
tECHnICAL DAtA
DRAWInGSBasic Gearbox
Output FlangeMounting
Torque Arm
Output Flange Output Flange
Output Shaft Insert
3.93
7
1.476
ø0.3
74
ø0.3741.969
3.9372.953
1.96
91.240 4.331
ø4.3
31
3.406 6.299
0.1180.394 0.354
5.118
- 0.0
014
- 0.0
028
0.1380.433
1.240 4.331
0.4333.406 7.874
ø5.1
18
6.496
- 0.0
017
- 0.0
033
0.157
0.512
1.240 4.331
0.4333.406 9.843
ø7.0
87- 0
.001
7- 0
.003
3
8.465
0
- 0.0
013
4.331
ø1.0
00
5/16-18
6.618
2.130x 0.83
0.250
1.11
0
2.287
6
F2SB
tA R/L
F4F3
5.94
5
Mounting holesposition
2.7564.331
ø3.1
50
3.9374 holes M8x0.472
2.03
9
1.988 0.118
2.75
6
StandardHollow shaft
+0.0008 0
- 0.0
012
- 0.0
024
øFA
D
C
B
Hollow Shaft B C D
Imperial 1.000” 1.118” 0.250”
Metric (mm) 25 28.3 8
X43 Nema Flanges øF A
56C 6.5” 8.787”
IEC Flanges øF (mm) A (mm)
63 B5 138 205
71 B5 160 202.5
56 B14 80 202.5
63 B14 90 205
71 B14 105 202.5
ø0.4
33
4.6460.787
4.25
2
1.96
9
1.18
1
5.827
X43
17.5pounds
Gearbox Weight
X52output Speed (RPM)
Ratio Motor Power (HP)
output torque (in-lbs)
Service Factor
oHL nom. torque (in-lbs)
Reducer Part number*
Gearmotor Part number*
290 6.05 1042 1.1
609 1195 RX52-0006-HSB2S-YGX52-0006-HSB2S-YAJ3B
3 625 1.9 GX52-0006-HSB2S-YAH3B
189 9.35 1601 0.9
674 1372 RX52-0009-HSB2S-YGX52-0009-HSB2S-YAJ3B
3 961 1.4 GX52-0009-HSB2S-YAH3B
154 11.45 1964 1
674 2036 RX52-0011-HSB2S-YGX52-0011-HSB2S-YAJ3B
3 1178 1.7 GX52-0011-HSB2S-YAH3B
114 15.43 1593 1.4
787 2213 RX52-0015-HSB2S-YGX52-0015-HSB2S-YAH3B
1.5 797 2.8 GX52-0015-HSB2S-XAF3B
100 17.53 1811 1.2
899 2213 RX52-0017-HSB2S-YGX52-0017-HSB2S-YAH3B
1.5 905 2.4 GX52-0017-HSB2S-XAF3B
88 20.03 2072 1.1
899 2213 RX52-0020-HSB2S-YGX52-0020-HSB2S-YAH3B
1.5 1036 2.1 GX52-0020-HSB2S-XAF3B
74 23.63 2448 0.9
921 2213 RX52-0023-HSB2S-YGX52-0023-HSB2S-YAH3B
1.5 1224 1.8 GX52-0023-HSB2S-XAF3B
72 24.53 2536 0.9
921 2213 RX52-0024-HSB2S-YGX52-0024-HSB2S-YAH3B
1.5 1268 1.7 GX52-0024-HSB2S-XAF3B
57 30.72 2122 1
921 2213 RX52-0031-HSB2S-XGX52-0031-HSB2S-XAG3B
1 1061 2.1 GX52-0031-HSB2S-XAE3B
49.5 35.41.5 1834 1.2
1079 2213 RX52-0035-HSB2S-XGX52-0035-HSB2S-XAF3B
1 1222 1.8 GX52-0035-HSB2S-XAE3B
46.6 37.61.5 1948 1.1
1079 2213 RX52-0038-HSB2S-XGX52-0038-HSB2S-XAF3B
1 1299 1.7 GX52-0038-HSB2S-XAE3B
35.9 48.71 1683 1.3
1079 2213 RX52-0049-HSB2S-XGX52-0049-HSB2S-XAE3B
0.5 842 2.6 GX52-0049-HSB2S-WAC3B
32.2 54.31 1878 1.2
1079 2213 RX52-0054-HSB2S-XGX52-0054-HSB2S-XAE3B
0.5 939 2.4 GX52-0054-HSB2S-WAC3B
23.4 74.80.75 1940 1
1517 1859 RX52-0075-HSB2S-WGX52-0075-HSB2S-WAD3B
0.5 1293 1.4 GX52-0075-HSB2S-WAC3B
Notes: All units shown are standard configuration. Input motor, output shaft and mounting options are available. Motor Specification: 230/460 VAC 60/50Hz, 3PH 1800 RPM Nom. - inverter duty *NEMA Input Sizes: W = 56C X = 143/5TC Y = 182/4TC Motors 1HP and greater meet EISA efficiency requirements.
7
High Efficiency Hypoid Speed Reducer0.5 - 5HP, 1195 - 2213 in-lbs, 23.4 - 290RPM
· All hardened and ground gears for high efficiency and quiet operation · Interchangeability with most global manufacturers
X52
tECHnICAL DAtA
Output FlangeMount
Torque Arm
Output Flange Output Flange
Output Shaft Insert
4.72
4
1.772
ø0.3
742.
362
ø0.3742.362
4.7243.543
X5A
1.417 5.118
ø4.3
31
3.976 6.299
0.1180.394 0.354
5.118- 0
.001
4- 0
.002
8 X5A
0.1380.512
1.417 5.118
0.4333.976 7.874
ø5.1
18
6.496
- 0.0
017
- 0.0
033
X
8.465
0.157
0.551
1.417 5.118
0.5513.976 9.843
ø7.0
87- 0
.001
7- 0
.003
3
0 -0.0
010
5.118
ø1.2
5
1/2-13 x 1.12
7.933
2.5002.815
0.250
1.36
0
8
F2SB
tA R/L
F4F3
DRAWInGSBasic Gearbox
6.92
9
Mounting holesposition
3.1505.118
ø3.7
40
4.5284 holes M8x0.591
1.33
9
2.362 0.118
3.15
0
StandardHollow shaft
+0.0010 0
- 0.0
014
- 0.0
028
X5A
øFA
D
C
B
Hollow Shaft B C D
Imperial 1.250” 1.370” 0.250”
Metric (mm) 30 33.3 8
X52 Nema Flanges øF A
56C - 143/5TC 6.5” 9.47”
182/4TC 8.88” 10.17”
IEC Flanges øF (mm) A (mm)
80/90 B5 200 236
100 B5 250 245
80 B14 120 236
90 B14 140 236
100 B14 160 245
ø0.4
33
5.3940.787
4.64
6
1.96
9
1.18
1
6.575
X5A
X52
28.2pounds
Gearbox Weight
X53output Speed (RPM)
Ratio Motor Power (HP)
output torque (in-lbs)
Service Factor
oHL nom. torque (in-lbs)
Reducer Part number**
Gearmotor Part number**
30.8 56.81 1922 1.2
1079 2213 RX53-0057-HSB2S-XGX53-0057-HSB2S-XAE3B
0.5 961 2.3 GX53-0057-HSB2S-WAC3B
26.6 65.81 2227 1.0
1079 2213 RX53-0066-HSB2S-XGX53-0066-HSB2S-XAE3B
0.5 1114 2.0 GX53-0066-HSB2S-WAC3B
22.7 77.20.75 1961 1.1
1517 2213 RX53-0077-HSB2S-WGX53-0077-HSB2S-WAD3B
0.5 1307 1.7 GX53-0077-HSB2S-WAC3B
20.1 87.20.75 2215 1.0
1517 2213 RX53-0087-HSB2S-WGX53-0087-HSB2S-WAD3B
0.5 1477 1.5 GX53-0087-HSB2S-WAC3B
19.0 92.20.75 2341 0.9
1517 2213 RX53-0092-HSB2S-WGX53-0092-HSB2S-WAD3B
0.5 1560 1.4 GX53-0092-HSB2S-WAC3B
17.4 100.50.5 1701 1.3
1517 2213 RX53-0100-HSB2S-WGX53-0100-HSB2S-WAC3B
0.25 850 2.6 GX53-0100-HSB2S-WAA3B
15.0 116.50.5 1971 1.1
1866 2213 RX53-0116-HSB2S-WGX53-0116-HSB2S-WAC3B
0.25 986 2.2 GX53-0116-HSB2S-WAA3B
13.9 125.80.5 2130 1.0
1866 2213 RX53-0126-HSB2S-WGX53-0126-HSB2S-WAC3B
0.25 1065 2.1 GX53-0126-HSB2S-WAA3B
12.4 141.70.5 2398 0.9
1866 2213 RX53-0142-HSB2S-WGX53-0142-HSB2S-WAC3B
0.25 1199 1.8 GX53-0142-HSB2S-WAA3B
10.7 163.20.33 1823 1.2
1866 2213 RX53-0163-HSB2S-WGX53-0163-HSB2S-WAB3B
0.25 1381 1.6 GX53-0163-HSB2S-WAA3B
9.8 179.00.33 1999 1.1
1866 2213 RX53-0179-HSB2S-WGX53-0179-HSB2S-WAB3B
0.25 1515 1.5 GX53-0179-HSB2S-WAA3B
9.1 193.40.33 2160 1.0
1866 2213 RX53-0193-HSB2S-WGX53-0193-HSB2S-WAB3B
0.25 1637 1.4 GX53-0193-HSB2S-WAA3B
8.1 216.80.33 2423 0.9
1866 2213 RX53-0217-HSB2S-WGX53-0217-HSB2S-WAB3B
0.25 1835 1.2 GX53-0217-HSB2S-WAA3B
6.9 252.4 0.25 2136 1.0 1866 2213 RX53-0252-HSB2S-W GX53-0252-HSB2S-WAA3B
6.0 290.7 0.25 2460 0.9 1866 2213 RX53-0291-HSB2S-W GX53-0291-HSB2S-WAA3B
5.3 333.2 0.25* 2820 0.8 1866 2213 RX53-0333-HSB2S-W GX53-0333-HSB2S-WAA3B
4.6 383.8 0.25* 3249 0.7 1866 2213 RX53-0384-HSB2S-W GX53-0384-HSB2S-WAA3B
3.9 446.7 0.25* 3781 0.6 1866 2213 RX53-0447-HSB2S-W GX53-0447-HSB2S-WAA3B
3.0 589.9 0.25* 4992 0.4 1866 2213 RX53-0590-HSB2S-W GX53-0590-HSB2S-WAA3B
Notes: *Power greater than that which can be supported by the gearbox for continuous duty.
All units shown are standard configuration. Input motor, output shaft and mounting options are available. Motor Specification: 230/460 VAC 60/50Hz, 3PH 1800 RPM Nom. - inverter duty *NEMA Input Sizes: W = 56CX = 143/5TCY = 182/4TC Motors 1HP and greater meet EISA efficiency requirements.
9
High Efficiency Hypoid Speed Reducer0.25 - 1HP, 2213 in-lbs, 3.0 - 30.8RPM
· All hardened and ground gears for high efficiency and quiet operation · Interchangeability with most global manufacturers
X53
tECHnICAL DAtA
Output FlangeMounting
Torque Arm
Output Flange Output Flange
Output Shaft Insert
4.72
4
1.772
ø0.3
742.
362
ø0.3742.362
4.7243.543
X5A - 0.0
014
- 0.0
028
1.417 5.118
ø4.3
31
3.976 6.299
0.1180.394 0.354
5.118
X5A
- 0.0
017
- 0.0
033
0.1380.512
1.417 5.118
0.4333.976 7.874
ø5.1
18
6.496
- 0.0
017
- 0.0
033
0.157
0.551
1.417 5.118
0.5513.976 9.843
ø7.0
87
8.465
0 -0.0
010
5.118
ø1.2
5
1/2-13 x 1.12
7.933
2.5002.815
0.250
1.36
0
10
F2SB
tA R/L
F4F3
DRAWInGSBasic Gearbox
StandardHollow shaft
+0.0010 07.
520
Mounting holesposition
3.1505.118
ø3.7
40
4.5284 holes M8x0.591
2.83
5
2.362 0.118
3.15
0
- 0.0
014
- 0.0
028
X5A
øFA
D
C
B
Hollow Shaft B C D
Imperial 1.250” 1.370” 0.250”
Metric (mm) 30 33.3 8
X53 Nema Flanges øF A
56C - 143/5TC 6.5” 9.47”
IEC Flanges øF (mm) A (mm)
71 B5 160 244
80/90 B5 200 246
71 B14 105 244
80 B14 120 246
90 B14 140 246ø0
.433
5.3940.787
4.64
51.
181
6.575
1.96
9
X5A
X53
27.9pounds
Gearbox Weight
X62output Speed (RPM)
Ratio Motor Power (HP)
output torque (in-lbs)
Service Factor
oHL nom. torque (in-lbs.)
Reducer Part number*
Gearmotor Part number*
290 6.05 1042 2.0
621 2124 RX62-0006-HSB2S-YGX62-0006-HSB2S-YAJ3B
3 625 3.4 GX62-0006-HSB2S-YAH3B
189 9.35 1601 1.5
674 2390 RX62-0009-HSB2S-YGX62-0009-HSB2S-YAJ3B
3 961 2.5 GX62-0009-HSB2S-YAH3B
154 11.45 1964 1.6
674 3098 RX62-0011-HSB2S-YGX62-0011-HSB2S-YAJ3B
3 1178 2.6 GX62-0011-HSB2S-YAH3B
114 15.45 2655 1.3
787 3408 RX62-0015-HSB2S-YGX62-0015-HSB2S-YAJ3B
3 1593 2.1 GX62-0015-HSB2S-YAH3B
100 17.55 3018 1.2
877 3540 RX62-0017-HSB2S-YGX62-0017-HSB2S-YAJ3B
3 1811 2.0 GX62-0017-HSB2S-YAH3B
88 20.05 3453 1.1
877 3629 RX62-0020-HSB2S-YGX62-0020-HSB2S-YAJ3B
3 2072 1.8 GX62-0020-HSB2S-YAH3B
74 23.65 4080 0.9
1000 3629 RX62-0023-HSB2S-YGX62-0023-HSB2S-YAJ3B
3 2448 1.5 GX62-0023-HSB2S-YAH3B
72 24.55 4226 0.9
1000 3629 RX62-0024-HSB2S-YGX62-0024-HSB2S-YAJ3B
3 2536 1.4 GX62-0024-HSB2S-YAH3B
57 30.73 3184 1.1
1000 3629 RX62-0031-HSB2S-YGX62-0031-HSB2S-YAH3B
1.5 1592 2.3 GX62-0031-HSB2S-XAF3B
49.5 35.43 3667 1.0
1281 3629 RX62-0035-HSB2S-YGX62-0035-HSB2S-YAH3B
1.5 1834 2.0 GX62-0035-HSB2S-XAF3B
46.6 37.63 3897 0.9
1281 3629 RX62-0038-HSB2S-YGX62-0038-HSB2S-YAH3B
1.5 1948 1.9 GX62-0038-HSB2S-XAF3B
35.9 48.72 3366 1.0
1281 3231 RX62-0049-HSB2S-XGX62-0049-HSB2S-XAG3B
1 1683 1.9 GX62-0049-HSB2S-XAE3B
32.2 54.32 3757 1.0
1281 3629 RX62-0054-HSB2S-XGX62-0054-HSB2S-XAG3B
1 1878 1.9 GX62-0054-HSB2S-XAE3B
23.4 74.81 2587 1.2
1495 3186 RX62-0075-HSB2S-XGX62-0075-HSB2S-XAE3B
0.5 1293 2.5 GX62-0075-HSB2S-WAC3B
Notes: All units shown are standard configuration. Input motor, output shaft and mounting options are available. Motor Specification: 230/460 VAC 60/50Hz, 3PH 1800 RPM Nom. - inverter duty *NEMA Input Sizes: W = 56CX = 143/5TCY = 182/4TC Motors 1HP and greater meet EISA efficiency requirements.
11
High Efficiency Hypoid Speed Reducer0.5 - 5HP, 2124 - 3629 in-lbs, 23.4 - 290RPM
· All hardened and ground gears for high efficiency and quiet operation · Interchangeability with most global manufacturers
X62
tECHnICAL DAtA
Output FlangeMounting
Torque Arm
Output Flange Output Flange
Output Shaft Insert
7.16
5
Mounting holesposition
3.5435.906
ø3.7
40
4.5284 holes M8x0.7871.
181
2.756 0.118
3.54
3
StandardHollow shaft
+0.0010 0
- 0.0
014
- 0.0
028
X6A
4.96
1
1.870
ø0.4
722.
480
ø0.4722.480
0.8663.740
4.961
X6A
1.417 5.906
ø4.3
31
4.370 6.299
0.1180.394 0.354
5.118
- 0.0
014
- 0.0
028
X6A
0.1380.512
1.417 5.906
0.4334.370 7.874
6.496
ø5.1
18- 0
.001
7- 0
.003
3
X
8.465
0.157
0.551
1.417 5.906
0.5514.370 9.843
ø7.0
87- 0
.001
7- 0
.003
3
0.313
1.51
0
0 -0.0
010
5.906
ø1.3
75
1/2-13x1.12
8.972
2.7523.067
12
F2SB
tA R/L
F4F3
DRAWInGSBasic Gearbox
øFA
D
C
B
Hollow Shaft B C D
Imperial 1.375” 1.520” 0.313”
Metric (mm) 35 38.3 10
X62 Nema Flanges øF A
56C - 143/5TC 6.5” 10.216”
182/4TC 8.88” 10.921”
IEC Flanges øF (mm) A (mm)
80/90 B5 200 255
100 B5 250 264
80 B14 120 255
90 B14 140 255
100 B14 160 264
ø0.8
27
5.9060.984
5.31
5
2.36
2
1.37
8
7.283
X6A
X62
34.8pounds
Gearbox Weight
X63output Speed (RPM)
Ratio Motor Power (HP)
output torque (in-lbs)
Service Factor
oHL nom. torque (in-lbs)
Reducer Part number**
Gearmotor Part number**
30.8 56.81.5 2883 1.3
1281 3629 RX63-0057-HSB2S-XGX63-0057-HSB2S-XAF3B
1 1922 1.9 GX63-0057-HSB2S-XAE3B
26.6 65.81.5 3341 1.1
1281 3629 RX63-0066-HSB2S-XGX63-0066-HSB2S-XAF3B
1 2227 1.6 GX63-0066-HSB2S-XAE3B
22.7 77.21.5 3922 0.9
1495 3629 RX63-0077-HSB2S-XGX63-0077-HSB2S-XAF3B
1 2615 1.4 GX63-0077-HSB2S-XAE3B
20.1 87.21 2953 1.2
1495 3629 RX63-0087-HSB2S-XGX63-0087-HSB2S-XAE3B
0.5 1477 2.5 GX63-0087-HSB2S-WAC3B
19.0 92.21 3121 1.2
1495 3629 RX63-0092-HSB2S-XGX63-0092-HSB2S-XAE3B
0.5 1560 2.3 GX63-0092-HSB2S-WAC3B
17.4 100.51 3402 1.1
1495 3629 RX63-0100-HSB2S-XGX63-0100-HSB2S-XAE3B
0.5 1701 2.1 GX63-0100-HSB2S-WAC3B
15.0 116.51 3943 0.9
1866 3629 RX63-0116-HSB2S-XGX63-0116-HSB2S-XAE3B
0.5 1971 1.8 GX63-0116-HSB2S-WAC3B
13.9 125.80.75 3195 1.1
1866 3629 RX63-0126-HSB2S-WGX63-0126-HSB2S-WAD3B
0.5 2130 1.7 GX63-0126-HSB2S-WAC3B
12.4 141.70.75 3597 1.0
1866 3629 RX63-0142-HSB2S-WGX63-0142-HSB2S-WAD3B
0.5 2398 1.5 GX63-0142-HSB2S-WAC3B
10.7 163.20.5 2762 1.3
1866 3629 RX63-0163-HSB2S-WGX63-0163-HSB2S-WAC3B
0.25 1381 2.6 GX63-0163-HSB2S-WAA3B
9.8 179.00.5 3030 1.2
1866 3629 RX63-0179-HSB2S-WGX63-0179-HSB2S-WAC3B
0.25 1515 2.4 GX63-0179-HSB2S-WAA3B
9.1 193.40.5 3273 1.1
1866 3629 RX63-0193-HSB2S-WGX63-0193-HSB2S-WAC3B
0.25 1637 2.2 GX63-0193-HSB2S-WAA3B
8.1 216.80.5 3671 1.0
1866 3629 RX63-0217-HSB2S-WGX63-0217-HSB2S-WAC3B
0.25 1835 2.0 GX63-0217-HSB2S-WAA3B
6.9 252.40.33 2819 1.3
1866 3629 RX63-0252-HSB2S-WGX63-0252-HSB2S-WAB3B
0.25 2136 1.7 GX63-0252-HSB2S-WAA3B
6.0 290.70.33 3248 1.1
1866 3629 RX63-0291-HSB2S-WGX63-0291-HSB2S-WAB3B
0.25 2460 1.5 GX63-0291-HSB2S-WAA3B
5.3 333.20.33 3723 1.0
1866 3629 RX63-0333-HSB2S-WGX63-0333-HSB2S-WAB3B
0.25 2820 1.3 GX63-0333-HSB2S-WAA3B
4.6 383.8 0.25 3249 1.1 1866 3629 RX63-0384-HSB2S-W GX63-0384-HSB2S-WAA3B
3.9 446.7 0.25 3781 1.0 1866 3629 RX63-0447-HSB2S-W GX63-0447-HSB2S-WAA3B
3.0 589.9 0.25* 4992 0.7 1866 3629 RX63-0590-HSB2S-W GX63-0590-HSB2S-WAA3B
Notes: *Power greater than that which can be supported by the gearbox for continuous duty.
All units shown are standard configuration. Input motor, output shaft and mounting options are available. Motor Specification: 230/460 VAC 60/50Hz, 3PH 1800 RPM Nom. - inverter duty *NEMA Input Sizes: W = 56CX = 143/5TCY = 182/4TC Motors 1HP and greater meet EISA efficiency requirements.
13
High Efficiency Hypoid Speed Reducer0.25 - 1.5HP, 3629 in-lbs, 3.0 - 30.8RPM
· All hardened and ground gears for high efficiency and quiet operation · Interchangeability with most global manufacturers
X63
tECHnICAL DAtA
Output FlangeMounting
Torque Arm
Output Flange Output Flange
Output Shaft Insert
4.96
1
1.870
ø0.4
722.
480
ø0.4722.480
0.8663.740
4.961
X6A
1.417 5.906
ø4.3
31
4.370 6.299
0.1180.394 0.354
5.118- 0
.001
4- 0
.002
8 X6A
0.1380.512
1.417 5.906
0.4334.370 7.874
ø5.1
18
6.496
- 0.0
017
- 0.0
033
0.157
0.551
1.417 5.906
0.5514.370 9.843
ø7.0
87- 0
.001
7- 0
.003
3
8.465
0 -0.0
010
5.906
ø1.3
75
1/2-13x1.12
8.972
2.7523.067
0.313
1.51
0
14
F2SB
tA R/L
F4F3
DRAWInGSBasic Gearbox
7.75
6
Mounting holesposition
3.5435.906
ø3.7
40
4.5284 holes M8x0.787
2.67
7
2.756 0.118
3.54
3
StandardHollow shaft
+0.0010 0
- 0.0
014
- 0.0
028
X6A
øFA
D
C
B
Hollow Shaft B C D
Imperial 1.375” 1.520” 0.313”
Metric (mm) 35 38.3 10
X63 Nema Flanges øF A
56C - 143/5TC 6.5” 10.807”
IEC Flanges øF (mm) A (mm)
71 B5 160 263
80/90 B5 200 265
71 B14 105 263
80 B14 120 265
90 B14 140 265ø0
.827
5.9060.984
5.31
5
2.36
2
1.37
8
7.283
X6A
X63
35.2pounds
Gearbox Weight
on request / Standard
B7B3 B8B6 V5 V6 V8
oil Quantity (oz.) Per Mounting PositionB3 B6 B7 B8 V5 V6 V8
X42 21.12 26.40 17.60 24.64 36.71 21.12
Consult Factory
X43 28.16 28.16 21.12 28.16 42.23 24.64X52 31.68 52.79 26.40 49.27 68.63 40.47X53 45.75 54.55 29.92 51.03 73.91 43.99X62 43.99 59.83 33.44 56.31 86.23 52.79X63 63.35 63.35 36.95 59.83 91.51 58.07
Standard Synthetic oil
ISO VG 220 320 Ambient temperatures -30°C - 80° C
SHELL OmalaS4 WF 320FG MOBIL Glygoyle 320
Oil Plugs Closed
15
High Efficiency Hypoid Speed Reducer
XSERIES
LuBRICAtIon· Units X42 - X63 are supplied with synthetic oil for lifetime lubrication, no maintenenace is required.
· The gearboxes are supplied with an oil quantity applicable for mounting positions B3 - V6.
· Special lubrication levels necessary for certain mounting positions. Please specify position when ordering: B6/B7/B8/V5/V6/V8.
FRFR
M Output Torqued diameter of driving elementFK Coefficient Factor
1.15 Gearwheels1.25 Chain sprockets1.75 narrow v-belt pulley 2.50 Flat-belt pulley
d [mm]fK
M [Nm] 2000FR [N] =
d [in]fK
M [lb in] 8.9FR [N] =
If your application requires higher radial loads, contact our technical office (1.800.282.4766). Higher load may be possible.
See data sheets for rated OHL.
16
oVERHunG LoAD· Overhung load generated by external transmissions keyed onto input and/or output shafts
-- Inch (Standard)
A Metric
InCH (StAnDARD)
X42/43Ø1.00
X52/53Ø1.25
X62/63Ø1.375
MetricX42/43
Ø25X52/53
Ø30X62/63
Ø35
XSERIES
High Efficiency Hypoid Speed Reducer
HoLLoW oP RAtIo - outPut SHAFt MountInG
MountInGPoSItIontYPE SIZE
X422 StagesX42X52X62
3 StagesX43X53X63
RR- ReducerG-Gearmotor
ø
0018See Ratio table for Selection
X42 X43 X52 X53 X62 X637.29 50.35 6.03 56.76 6.03 56.7611.2 55.22 9.26 65.79 9.26 65.7913.2 59.92 11.36 77.23 11.36 77.2315.27 65.72 15.36 87.23 15.36 87.2317.93 71.78 17.46 92.18 17.46 92.1820.25 79.44 19.97 100.47 19.97 100.4721.4 92.08 23.6 116.45 23.6 116.4523.47 95.03 24.45 125.82 24.45 125.8227.55 126.55 30.69 141.66 30.69 141.6629.21 133.15 35.35 163.16 35.35 163.1632.88 150.18 37.57 178.96 37.57 178.9638.12 177.3 48.68 193.36 48.68 193.3644.89 210.42 54.33 216.84 54.33 216.8450.34 230.79 74.81 252.36 74.81 252.3658.58 272.47 290.67 290.6777.36 323.37 333.23 333.23
383.82 383.82446.7 446.7
589.85 589.85
HH HollowR Right Ext.L Left Ext.
H
Hollow Output Shaft
R
Single Output Shaft
ø
SBSB Standard
BaseF2 OP Flange 2F3 OP Flange 3F4 OP Flange 4TA Torque Arm
ø
SB F2
Output FlangesF2 Ø6.299F3 Ø7.874F4 Ø9.843
tA
MOUNTING ACCESSORIES
SHIPPED LOOSE WITH UNIT
22 B33 B64 B75 B86 V57 V6
B3
B7
B6
B8
V5
V6
17
EXAMPLE:17.93 = 0018 589.85 = 0590 100.47 = 0100
ø
Flange
PRoDuCt SELECtIon tABLES
LuBRICAtIon -MotoR
Mount StYLE MotoR/PoWER tYPE noM. MotoR RPM MotoR PoSItIon
AD
3PH AC Inverter Duty Motors (C-Face, Footless)AA INV.DUTY, 0.25HP (.18KW), 230/460V
AB INV.DUTY, 0.33HP (.25KW), 230/460V
AC INV.DUTY, 0.5HP (.37KW), 230/460V
AD INV.DUTY, 0.75HP (.55KW), 230/460V
AE INV.DUTY, 1.0HP (.75KW), 230/460V
AF INV.DUTY,1.5HP (1.1KW), 230/460V
AG INV.DUTY, 2HP (1.5KW), 230/460V
AH INV.DUTY, 3HP (2.2KW), 230/460V
AJ INV.DUTY, 5HP, 230/460V
Brake Motors (3PH, C-Face, Removable Base)BA BRAKE MOTOR, 0.5HP (.37KW), 230/460V
BB BRAKE MOTOR, 0.75HP (.55KW), 230/460V
BC BRAKE MOTOR, 1.0HP (.75KW), 230/460V
BD BRAKE MOTOR, 1.5HP (1.1KW), 230/460V
BE BRAKE MOTOR, 2HP (1.5KW), 230/460V
BF BRAKE MOTOR, 3HP (2.2KW), 230/460V
BG BRAKE MOTOR, 5HP, 230/460V, 3PH
Single Phase AC Motors (C-Face, Footless)CA SINGLE PHASE, 0.25HP, 115/230VAC
CB SINGLE PHASE, 0.33HP, 115/230VAC
CC SINGLE PHASE, 0.5HP, 115/230VAC
CD SINGLE PHASE, 0.75HP, 115/230VAC
CE SINGLE PHASE, 1.0HP, 115/230VAC
CF SINGLE PHASE, 1.5HP, 115/230VAC
SEE PAGE 49 FOR MORE MOTOR OPTIONS
SS StandardF Food
Grade
StandardShell Omala S4 WE 320
Food GradeMobile
Glygoyle 320
ALL OPTIONS ARE HIGH
GRADE SYNTHETIC
OIL
BA 270°B 0°C 90°
D 180°
C
A
D
B
18
WNemaW 56C (Ø = 6.5”)X 143/5TC
(Ø = 6.5”)Y 182/4TC
(Ø = 8.875”)
IEC - B5A 56 (Ø = 120)B 63 (Ø = 140)C 71 (Ø = 160)D 80 (Ø = 200)E 90 (Ø = 200)F 100/112
(Ø = 250)
IEC - B14O 56 (Ø = 80)P 63 (Ø = 90)Q 71 (Ø = 105)R 80 (Ø = 120)T 90 (Ø = 140)U 100/112
(Ø = 160)
SAMPLE PART NUMBERS: RX42-0018-HSB2S-W, GX63-0100-HF32S-XAE3B
32 12003 18004 3600
(StAnDARD)
oversized BearingsSupport positively-retained, high speed shaft for higher shock load capacity - ideal for frequent starting and reversing application. Premium, Nitrile® high temperature seals each end.
Premium, High temperaturenitrile® output Seals. (Viton® Seals available)
Standard Hollow output Shaft Mounting Reduces total drive envelope size, weight and cost. Single output shaft is available.
QSERIES
QSE
RIES Aluminum Integral HP Worm Speed Reducer
Vent Free Design.No breather or vents to leak! Factory lubricated for life with synthetic, semi-fluid gear lubricant with an operating range of -15ºC to 130ºC.
Single-Piece Aluminum Alloy HousingIs vacuum impregnated (MIL-STD 276) for protection and sealing. No secondary finish required but readily accepts paint. Combines light weight with high tensile strength. Precision machined for alignment of bearings and gearing. Single Piece Alloy Steel Input Shaft
and Worm ShaftHigh helix angle worm is case-hardened (Rc 58-60), ground, teeth are profiled and radiused, for noise reduction and enhanced efficiency.
Machined Bearing CapsWith exterior machined surfaces enable a variety of mounting accessories. Extra-deep thread engagement provided for greater support strength. Zinc plated hardware.
oversize Bearing For radial load capability and maximum hollow shaft diameter.
Bronze Alloy Worm GearsIs centrifugally cast onto an iron hub for maximum strength and superior life.
20
100% Factory Pressure Leak tested
Q45output Speed (RPM)
Ratio Motor Power (HP)
output torque (in-lbs)
Service Factor
oHL nom. torque (in-lbs)
Reducer Part number*
Gearmotor Part number*
250 71 202 1.3
187 257 RQ45-0007-HSB2S-WGQ45-0007-HSB2S-WAE3B
0.5 101 2.5 GQ45-0007-HSB2S-WAC3B
175 100.75 213 1.2
202 257 RQ45-0010-HSB2S-WGQ45-0010-HSB2S-WAD3B
0.5 142 1.8 GQ45-0010-HSB2S-WAC3B
125 140.5 194 1.3
225 257 RQ45-0014-HSB2S-WGQ45-0014-HSB2S-WAC3B
0.25 97 2.6 GQ45-0014-HSB2S-WAA3B
83.3 210.5 253 1.4
247 345 RQ45-0021-HSB2S-WGQ45-0021-HSB2S-WAC3B
0.25 127 2.7 GQ45-0021-HSB2S-WAA3B
62.5 280.5 328 1.1
270 345 RQ45-0028-HSB2S-WGQ45-0028-HSB2S-WAC3B
0.25 164 2.1 GQ45-0028-HSB2S-WAA3B
47.3 370.33 277 1.2
315 345 RQ45-0037-HSB2S-WGQ45-0037-HSB2S-WAB3B
0.25 210 1.6 GQ45-0037-HSB2S-WAA3B
38.0 460.33 323 1.1
315 345 RQ45-0046-HSB2S-WGQ45-0046-HSB2S-WAB3B
0.25 244 1.4 GQ45-0046-HSB2S-WAA3B
29.2 60 0.25 303 1.1 315 345 RQ45-0060-HSB2S-W GQ45-0060-HSB2S-WAA3B
25.0 70 0.25 340 0.8 405 257 RQ45-0070-HSB2S-W GQ45-0070-HSB2S-WAA3B
17.2 102 0.25 450 <0.8 405 248 RQ45-0102-HSB2S-W GQ45-0102-HSB2S-WAA3B
Notes: All units shown are standard configuration. Input motor, output shaft and mounting options are available. Motor Specification: 230/460 VAC 60/50Hz, 3PH 1800 RPM Nom. - inverter duty *NEMA Input Sizes: W = 56C X = 143/5TC Y = 182/4TC
21
Integral HP Worm Speed Reducer0.25 - 1HP, 257 - 345 in-lbs, 17.2 - 250RPM
· Precision machined single-piece aluminum housing combines light weight with long product life · Interchangeability with most global manufacturers
Q45
tECHnICAL DAtA
Square Flange Mounting
Torque Arm Output Shaft Insert
Q3.740
O
1.969
PG
2.559N
L
E
ØD
2.559
2.7952.362
561.2873.1
4.78
3
0.26
3.937
2.362
1.77
2
1.969
1.96
9
2.756
2.756
2.81
5
1.437
0.55
2.36
2
0.16
0.39
4.6463.937
1.969
2.0471.929
1/4-20 UNC
0.830
5781.0
4.8032.756
0.75
0
type B ØD E G L N O P Q
F2 2.36402.3622 0.16 0.28 2.638 1.358 2.953 4.331 0.35
22
SBF2
tA R/L
DRAWInGSBasic Gearbox
2.953
4 6x0.47holes M
2.559
1.437
2.36
2
0.098
1.96
92.
815
1.77
2
1.969
Mounting Hole Postions
Standard Hollow Shaft
D
C
B
Hollow Shaft B C D
Imperial 0.750” 0.841” 0.1875”
Metric (mm) 18 20.8 6
Q45 Nema Flanges øF A
56C 6.5” 3.846”
IEC Flanges øF (mm) A (mm)
63 B5 140 80
71 B5 160 77.5
63 B14 90 80
71 B14 105 77.5
A
øF
Q45
5.1pounds
Gearbox Weight
Q50output Speed (RPM)
Ratio Motor Power (HP)
output torque (in-lbs)
Service Factor
oHL nom. torque (in-lbs)
Reducer Part number*
Gearmotor Part number*
250 72 413 1.2
256 478 RQ50-0007-HSB2S-WGQ50-0007-HSB2S-WAG3B
1 207 2.3 GQ50-0007-HSB2S-WAE3B
175 101.5 432 1.2
270 522 RQ50-0010-HSB2S-WGQ50-0010-HSB2S-WAF3B
1 288 1.8 GQ50-0010-HSB2S-WAE3B
125 141 398 1.4
315 575 RQ50-0014-HSB2S-WGQ50-0014-HSB2S-WAE3B
0.5 199 2.9 GQ50-0014-HSB2S-WAC3B
97.2 181 486 1.1
337 522 RQ50-0018-HSB2S-WGQ50-0018-HSB2S-WAE3B
0.5 243 2.1 GQ50-0018-HSB2S-WAC3B
67.3 260.75 485 1.2
382 558 RQ50-0026-HSB2S-WGQ50-0026-HSB2S-WAD3B
0.5 323 1.7 GQ50-0026-HSB2S-WAC3B
58.3 300.75 567 1.1
382 611 RQ50-0030-HSB2S-WGQ50-0030-HSB2S-WAD3B
0.5 378 1.6 GQ50-0030-HSB2S-WAC3B
40.7 430.5 511 1.1
427 575 RQ50-0043-HSB2S-WGQ50-0043-HSB2S-WAC3B
0.25 256 2.3 GQ50-0043-HSB2S-WAA3B
29.2 600.33 414 1.3
427 522 RQ50-0060-HSB2S-WGQ50-0060-HSB2S-WAB3B
0.25 313 1.7 GQ50-0060-HSB2S-WAA3B
25.7 680.33 461 1.1
427 487 RQ50-0068-HSB2S-WGQ50-0068-HSB2S-WAB3B
0.25 349 1.4 GQ50-0068-HSB2S-WAA3B
21.9 80 0.25 389 1.2 562 478 RQ50-0080-HSB2S-W GQ50-0080-HSB2S-WAA3B
17.5 100 0.25 450 1.0 562 434 RQ50-0100-HSB2S-W GQ50-0100-HSB2S-WAA3B
Notes: All units shown are standard configuration. Input motor, output shaft and mounting options are available. Motor Specification: 230/460 VAC 60/50Hz, 3PH 1800 RPM Nom. - inverter duty *NEMA Input Sizes: W = 56CX = 143/5TCY = 182/4TC
23
Integral HP Worm Speed Reducer0.25 - 2HP, 434 - 611 in-lbs, 17.5 - 250RPM
· Precision machined single-piece aluminum housing combines light weight with long product life · Interchangeability with most global manufacturers
Q50
tECHnICAL DAtA
Square Flange Mounting
Torque Arm Output Shaft Insert
Q4.331
O
2.362
PG
3.189N
L
E
ØD
3.189
3.3462.756
575.12.
520
5.66
9
0.33
4.724
2.756
1.96
9
2.362
2.36
2
3.150
3.150
3.30
7
1.713
0.55
2.75
6
0.16
0.39
4.6463.937
2.362
2.2872.130 1.11
0.25
5.6933.405
1.00
type B ØD E G L N O P Q
F2 2.75772.7559 0.20 0.35 3.543 1.949 3.346 4.921 0.43
24
SBF2
tA R/L
DRAWInGSBasic Gearbox
Mounting Hole Postions
Standard Hollow Shaft
4 8x0.43holes M
3.189
1.713
2.75
6
0.098
2.36
23.
307
1.96
9
2.362
3.346
D
C
B
Hollow Shaft B C D
Imperial 1.000” 1.114” 0.25”
Metric (mm) 25 28.3 8
Q50 Nema Flanges øF A
56C 6.5” 4.004”
IEC Flanges øF (mm) A (mm)
71 B5 160 81
80 B5 200 81.5
71 B14 105 81
80 B14 120 81.5
All Ratios
7:1 to 30:1
All Ratios
7:1 to 30:1
A
øF
5/16-18UNC
Q50
7.2pounds
Gearbox Weight
Q63output Speed (RPM)
Ratio Motor Power (HP)
output torque (in-lbs)
Service Factor
oHL nom. torque (in-lbs)
Reducer Part number*
Gearmotor Part number*
250 72 419 2.5
385 1053 RQ63-0007-HSB2S-XGQ63-0007-HSB2S-XAG3B
1 209 5 GQ63-0007-HSB2S-XAE3B
175 102 583 1.9
404 1133 RQ63-0010-HSB2S-XGQ63-0010-HSB2S-XAG3B
1 292 3.9 GQ63-0010-HSB2S-XAE3B
116.7 152 854 1.4
450 1159 RQ63-0015-HSB2S-XGQ63-0015-HSB2S-XAG3B
1 427 2.7 GQ63-0015-HSB2S-XAE3B
92.1 192 1068 1.1
517 1159 RQ63-0019-HSB2S-XGQ63-0019-HSB2S-XAG3B
1 534 2.2 GQ63-0019-HSB2S-XAE3B
72.9 241.5 972 1.2
562 1195 RQ63-0024-HSB2S-XGQ63-0024-HSB2S-XAF3B
1 648 1.8 GQ63-0024-HSB2S-XAE3B
58.3 301.5 1199 1
562 1230 RQ63-0030-HSB2S-XGQ63-0030-HSB2S-XAF3B
1 800 1.5 GQ63-0030-HSB2S-XAE3B
38.9 451 1070 1.1
674 1142 RQ63-0045-HSB2S-XGQ63-0045-HSB2S-XAE3B
0.5 535 2.1 GQ63-0045-HSB2S-WAC3B
26.1 670.5 724 1.4
674 1044 RQ63-0067-HSB2S-WGQ63-0067-HSB2S-WAC3B
0.25 362 2.9 GQ63-0067-HSB2S-WAA3B
21.9 800.5 821 1.2
854 1000 RQ63-0080-HSB2S-WGQ63-0080-HSB2S-WAC3B
0.25 411 2.4 GQ63-0080-HSB2S-WAA3B
18.6 940.5 880 1.1
854 1000 RQ63-0094-HSB2S-WGQ63-0094-HSB2S-WAC3B
0.25 440 2.3 GQ63-0094-HSB2S-WAA3B
Notes: All units shown are standard configuration. Input motor, output shaft and mounting options are available. Motor Specification: 230/460 VAC 60/50Hz, 3PH 1800 RPM Nom. - inverter duty *NEMA Input Sizes: W = 56CX = 143/5TCY = 182/4TC Motors 1HP and greater meet EISA efficiency requirements.
25
Integral HP Worm Speed Reducer0.25 - 2HP, 1000 - 1230 in-lbs, 18.6 - 250RPM
· Precision machined single-piece aluminum housing combines light weight with long product life · Interchangeability with most global manufacturers
Q63
tECHnICAL DAtA
26
Square Flange Mounting
Torque Arm Output Shaft Insert
Q5.591
O
2.854
PG
4.724N
L
E
ØD
21
4.724
3.7012.992
1.47
6800.2
800.2
7.18
5
0.37
5.709
2.992
2.48
0
2.854
2.85
4
4.016
4.016
4.33
1
2.087
0.79
ø2.9
53
0.24
0.43
7.0875.906
2.854
b1 o1
t2
n1m1 e1
c1
d1
type B ØD E G L N O P Q
F2 4.53544.5335 0.24 0.47 3.386 1.024 5.906 7.087 0.43
b1 c1 d1 e1 m1 n1 t2 o1
Standard 0.25 2.240 1.125 2.437 4.992 7.429 1.23 5/16-18
SBF2
tA R/L
DRAWInGSBasic Gearbox
Mounting Hole Postions
Standard Hollow Shaft
4.724
2.087
ø2.9
53
0.118
22.5°
45°
12 holes M8x0.55
3.543
2.85
44.
331
2.48
0
2.854
D
C
B
Hollow Shaft B C D
Imperial 1.125” 1.245” 0.25”
Metric (mm) 25 28.3 8
Q63 Nema Flanges øF A
56C - 143/5TC 6.5” 4.291”
IEC Flanges øF (mm) A (mm)
80 B5 200 99.5
90 B5 200 99.5
80 B14 120 99.5
90 B14 140 99.5
All Ratios
7:1 to 30:1
All Ratios
7:1 to 30:1
A
øF
Q63
13.2pounds
Gearbox Weight
Q85output Speed (RPM)
Ratio Motor Power (HP)
output torque (in-lbs)
Service Factor
oHL nom. torque (in-lbs)
Reducer Part number*
Gearmotor Part number*
250 75 1109 2.0
529 2168 RQ85-0007-HSB2S-YGQ85-0007-HSB2S-YAJ3B
3 666 3.3 GQ85-0007-HSB2S-YAH3B
175 105 1441 1.7
562 2390 RQ85-0010-HSB2S-YGQ85-0010-HSB2S-YAJ3B
3 864 2.8 GQ85-0010-HSB2S-YAH3B
125 145 1967 1.3
652 2567 RQ85-0014-HSB2S-YGQ85-0014-HSB2S-YAJ3B
3 1180 2.2 GQ85-0014-HSB2S-YAH3B
87.5 203 1707 1.5
674 2478 RQ85-0020-HSB2S-YGQ85-0020-HSB2S-YAH3B
1.5 854 2.9 GQ85-0020-HSB2S-XAF3B
62.5 283 2269 1.3
787 2921 RQ85-0028-HSB2S-YGQ85-0028-HSB2S-YAH3B
1.5 1135 2.6 GQ85-0028-HSB2S-XAF3B
46.1 383 2915 1.0
899 2832 RQ85-0038-HSB2S-YGQ85-0038-HSB2S-YAH3B
1.5 1458 1.9 GQ85-0038-HSB2S-XAF3B
33.7 522 2472 1.0
899 2434 RQ85-0052-HSB2S-YGQ85-0052-HSB2S-XAG3B
1 1236 2.0 GQ85-0052-HSB2S-XAE3B
26.1 671.5 2353 1.0
899 2434 RQ85-0067-HSB2S-XGQ85-0067-HSB2S-XAF3B
1 1569 1.6 GQ85-0067-HSB2S-XAE3B
23.7 741.5 2319 1.0
1124 2257 RQ85-0074-HSB2S-XGQ85-0074-HSB2S-XAF3B
1 1546 1.5 GQ85-0074-HSB2S-XAE3B
18.2 961 1833 1.1
1124 2036 RQ85-0096-HSB2S-XGQ85-0096-HSB2S-XAE3B
0.5 916 2.2 GQ85-0096-HSB2S-WAC3B
Notes: All units shown are standard configuration. Input motor, output shaft and mounting options are available. Motor Specification: 230/460 VAC 60/50Hz, 3PH 1800 RPM Nom. - inverter duty *NEMA Input Sizes: W = 56CX = 143/5TCY = 182/4TC Motors 1HP and greater meet EISA efficiency requirements.
27
Integral HP Worm Speed Reducer0.5 - 5HP, 2036 - 2921 in-lbs, 18.2 - 250RPM
· Precision machined single-piece aluminum housing combines light weight with long product life · Interchangeability with most global manufacturers
Q85
tECHnICAL DAtA
Square Flange Mounting
Torque Arm Output Shaft Insert
G
5.315N
L
E
ØD
O P
Q
3.937
21
5.315
4.9213.976
1.79
1538.2
538.2
9.66
5
0.43
7.874
3.976
3.34
6
3.937
3.93
7
5.669
5.669
5.72
8
2.520
0.98
4.33
1
0.24
0.83
9.4497.874
3.937
3.6023.406
3/8-16UNC
1.658
0.37
5
9.1535.551
1.50
0
type B ØD E G L N O P Q
F2 5.98675.9843 0.20 0.63 4.252 1.594 6.929 8.071 0.51
28
SBF2
tA R/L
DRAWInGSBasic Gearbox
Mounting Hole Postions
Standard Hollow Shaft
5.315
2.520
4.33
1
0.138
3.93
75.
728
3.34
6
3.937
8 10x0.67holes M
5.118
D
C
B
Hollow Shaft B C D
Imperial 1.500” 1.670” 0.375”
Metric (mm) 35 38.3 10
Q85 Nema Flanges øF A
56C - 143/5TC 6.5” 4.823”
182/4TC 8.88” 5.528”
IEC Flanges øF (mm) A (mm)
80/90 B5 200 118
80 B14 120 118
90 B14 140 118
A
øF
Q85
41.2pounds
Gearbox Weight
LuBRICAtIon
oVERHunG LoAD · Overhung load generated by external transmissions keyed onto input and/or output shafts
29
FR
FR
Integral HP Worm Speed Reducer
Worm Reducers QSERIES
M Output Torqued diameter of driving elementFK Coefficient Factor
1.15 Gearwheels1.25 Chain sprockets1.75 Narrow v-belt pulley 2.50 Flat-belt pulley
d [mm]fK
M [Nm] 2000FR [N] =
d [in]fK
M [lb in] 8.9FR [N] =
B7B3 B8B6 V5 V6
oil Quantity (oz.) Per Mounting PositionB3 B6 B7 B8 V5 V6
Q45 3.17 3.17 3.17 3.17 3.17 3.17Q50 4.93 4.93 4.93 4.93 4.93 4.93Q63 10.56 10.56 10.56 10.56 10.56 10.56Q85 42.23 42.23 42.23 42.23 42.23 42.23
oil Quantity (oz.) Per Mounting Position
30
Q/S45 Q/S50 Q/S63 Q/S85
>25° 7 7 712° - 25° 10/14 7/10 10/15 10/14/20/228° - 12° 21 14/18 19/245° - 8° 28 26/36 30/36 28/38/46/523° - 5° 37/46/68 43/60/68 45/60/67/80 67/74/961° - 3° 70/102 80/100 94
>25° · Totally reversible
12° - 25°· Statically reversible· Quick return· Dynamically reversible
8° - 12°· Variable static non-reversing quick return in case of vibrations · Dynamically reversible
5° - 8°· Static non-reversing return in case of vibrations · bad dynamic reversing
3° - 5°· Statically non-reversing return in case of vibrations · Low dynamic reversing*
1° - 3° · Statically non-reversing no return· Low dynamic reversing*
*Elimination of backdrive not guaranteed. Where required, an external break is recommended.
A
60
100
80
0
20
40C°
1 Time (h)
0/80% of Power
100% Power SF=1
Thermal limit with intermittant duty.Thermal limit B
1 Time (h)
60
100
80
0
20
40C°
C
T1 TT 1T
60
100
80
0
20
40C°
1 Time (h)
D
100% Power100% of Power
50% of Power 50% of Power
Time (h)
60
100
80
0
20
40C°
1
A - Temperature Increase depending on operating time. Final temperature is based on these variables: · Installed power and percentage of use · Ambient temperature · Lubrication · Cooling Method · Input speed
B - The temperature increase curve is similar to continuous duty. Peak is reached in 20/30 minutes using 100% of the power. The gearbox can be stopped at any point on this curve. Follow cooling curve (graph B) where shape depends on ambient operating temperature.
Thermal limit with intermittant duty. Thermal limit with intermittant duty.
BACk DRIVE· With worm gearboxes it is important to consider the several levels of reversibility of the worm gear set, in order to guarantee the correct selection in applications where these requirements are essential for the operation of the machine. The table belows shows the different levels of back drive for worm gearboxes according to helix angle ß and reduction ratio i.
tHERMAL LIMIt· Due to the internal design, worm gearboxes transform their installed power into heat which is dissipated through the housing. Typical safety temperature ranges are between 80° - 100°C. See graphs below:
· C & D - Should gearbox have several start/stop cycles, final temperature will depend on start/stop times and frequency. Service factors given in this catalog are based on intermittent duty.
· Gearmotors with 2800 min-1 input speed are tolerated at intermittent duty only, due to temperature rise from input rotation speed.
22 B33 B64 B75 B86 V57 V6
-- Inch (Standard)A Metric (Steel)B Inch (SS)C Metric (SS)
Inch (Standard)Q45
Ø0.75Q50
Ø1.00Q63
Ø1.125Q85
Ø1.500
MetricQ45
Ø18Q50
Ø25Q63
Ø25Q85
Ø35
Integral HP Worm Speed Reducer
HoLLoW oP RAtIo - outPut SHAFt MountInG
MountInGPoSItIontYPE SIZE
Q45AluminumQ45Q50Q63Q85
RR- ReducerG-Gearmotor
0018See Ratio table for Selection
Q45 Q50 Q63 Q857 7 7 7
10 10 10 1014 14 15 1421 18 19 2028 26 24 2837 30 30 3846 43 45 5260 60 - 6770 68 67 74
102 80 80 96100 94
7:1 = 0007 18:1 = 0018 96:1 = 0096
B3
B7
B6
B8
V5
V6
Worm Reducers QSERIES
ø
HH HollowR Right Ext.L Left Ext.
SBSB Standard
BaseF2 OP Flange 2TA Torque Arm
SB
F2
tA
MOUNTING ACCESSORIES
SHIPPED LOOSE WITH UNIT
H
Hollow Output Shaft
L
Single Output Shaft
31
PRoDuCt SELECtIon tABLES
LuBRICAtIon -MotoR
Mount StYLE MotoR/PoWER tYPE noM. MotoR RPM MotoR PoSItIon
BA 270°B 0°C 90°
D 180°
32 12003 18004 3600
SS StandardF Food
Grade
StandardShell Omala S4 WE 320
Food GradeMobile
Glygoyle 320
ALL OPTIONS ARE HIGH
GRADE SYNTHETIC
OIL
C
A
D
B
32
WNemaW 56C (Ø = 6.5”)X 143/5TC
(Ø = 6.5”)Y 182/4TC
(Ø = 8.875”)
IEC - B5A 56 (Ø = 120)B 63 (Ø = 140)C 71 (Ø = 160)D 80 (Ø = 200)E 90 (Ø = 200)F 100/112
(Ø = 250)
IEC - B14O 56 (Ø = 80)P 63 (Ø = 90)Q 71 (Ø = 105)R 80 (Ø = 120)T 90 (Ø = 140)U 100/112
(Ø = 160)
ø
Flange
SAMPLE PART NUMBERS: RQ50-0018-HSB2S-W, GQ85-0010-HF23S-YAJ3B
AD
3PH AC Inverter Duty Motors (C-Face, Footless)AA INV.DUTY, 0.25HP (.18KW), 230/460V
AB INV.DUTY, 0.33HP (.25KW), 230/460V
AC INV.DUTY, 0.5HP (.37KW), 230/460V
AD INV.DUTY, 0.75HP (.55KW), 230/460V
AE INV.DUTY, 1.0HP (.75KW), 230/460V
AF INV.DUTY,1.5HP (1.1KW), 230/460V
AG INV.DUTY, 2HP (1.5KW), 230/460V
AH INV.DUTY, 3HP (2.2KW), 230/460V
AJ INV.DUTY, 5HP, 230/460V
Brake Motors (3PH, C-Face, Removable Base)BA BRAKE MOTOR, 0.5HP (.37KW), 230/460V
BB BRAKE MOTOR, 0.75HP (.55KW), 230/460V
BC BRAKE MOTOR, 1.0HP (.75KW), 230/460V
BD BRAKE MOTOR, 1.5HP (1.1KW), 230/460V
BE BRAKE MOTOR, 2HP (1.5KW), 230/460V
BF BRAKE MOTOR, 3HP (2.2KW), 230/460V
BG BRAKE MOTOR, 5HP, 230/460V, 3PH
Single Phase AC Motors (C-Face, Footless)CA SINGLE PHASE, 0.25HP, 115/230VAC
CB SINGLE PHASE, 0.33HP, 115/230VAC
CC SINGLE PHASE, 0.5HP, 115/230VAC
CD SINGLE PHASE, 0.75HP, 115/230VAC
CE SINGLE PHASE, 1.0HP, 115/230VAC
CF SINGLE PHASE, 1.5HP, 115/230VAC
SEE PAGE 49 FOR MORE MOTOR OPTIONS
(StAnDARD)
optionsProtective seals cup to withstand high pressure cleaning for hollow or extended shaft version.
output shaft Interchangeable right or left hand output shafts available.
Stainless SteelHollow Shaft
o-Rings on All Closing Covers
SSERIES
SSER
IES Stainless Steel Integral HP
Worm Speed Reducer
Vent Free Design.No breather or vents to leak! Factory lubricated for life with synthetic, semi-fluid gear lubricant with an operating range of -15ºC to 130ºC.
34
Second BearingStandard second bearing on motor flange side.
Single-Piece Stainless Steel Alloy HousingSpecial housing designed to keep adequate lubrication with low oil quantity to avoid internal pressures. Flange
Fully modular to NEMA C Flange or IEC B14.
100% Factory Pressure Leak testedViton ® output Seals
With external dust protection lips standard.
S45output Speed (RPM)
Ratio Motor Power (HP)
output torque (in-lbs)
Service Factor
oHL nom. torque (in-lbs)
Reducer Part number*
Gearmotor Part number*
250 71 202 1.3
187 257 RS45-0007-HSB2S-WGS45-0007-HSB2S-WAE3B
0.5 101 2.5 GS45-0007-HSB2S-WAC3B
175 100.75 213 1.2
202 257 RS45-0010-HSB2S-WGS45-0010-HSB2S-WAE3B
0.5 142 1.8 GS45-0010-HSB2S-WAC3B
125 140.5 194 1.3
225 257 RS45-0014-HSB2S-WGS45-0014-HSB2S-WAC3B
0.25 97 2.6 GS45-0014-HSB2S-WAA3B
83.3 210.5 253 1.4
247 345 RS45-0021-HSB2S-WGS45-0021-HSB2S-WAC3B
0.25 127 2.7 GS45-0021-HSB2S-WAA3B
62.5 280.5 328 1.1
270 345 RS45-0028-HSB2S-WGS45-0028-HSB2S-WAC3B
0.25 164 2.1 GS45-0028-HSB2S-WAA3B
47.3 370.33 277 1.2
315 345 RS45-0037-HSB2S-WGS45-0037-HSB2S-WAB3B
0.25 210 1.6 GS45-0037-HSB2S-WAA3B
38.0 460.33 323 1.1
315 345 RS45-0046-HSB2S-WGS45-0046-HSB2S-WAB3B
0.25 244 1.4 GS45-0046-HSB2S-WAA3B
29.2 60 0.25 303 1.1 315 345 RS45-0060-HSB2S-W GS45-0060-HSB2S-WAA3B
25.0 70 0.25 340 0.8 405 257 RS45-0070-HSB2S-W GS45-0070-HSB2S-WAA3B
17.2 102 0.25 405 <0.8 450 248 RS45-0102-HSB2S-W GS45-0102-HSB2S-WAA3B
Notes: All units shown are standard configuration. Input motor, output shaft and mounting options are available. Motor Specification: 230/460 VAC 60/50Hz, 3PH 1800 RPM Nom. - inverter duty *NEMA Input Sizes: W = 56CX = 143/5TCY = 182/4TC
35
Stainless Steel Integral HP Worm Speed Reducer0.25 - 1HP, 248 - 345 in-lbs, 17.2 - 250RPM
· Stainless steel housing for food processing, medical and pharmaceutical applications · Interchangeability with most global manufacturers
S45
tECHnICAL DAtA
Hollow Shaft B C D
Imperial 0.750” 0.841” 0.1875”
Metric (mm) 18 20.8 6
36
DRAWInGSBasic Gearbox
Modular Base
Torque Arm Output Shaft Insert
Mounting Hole Positions
Standard Hollow Shaft
Side (A) Mounting Holes
5.00
0
(A)
0.82
7
3.386
1.693
1.65
4
2.520
2.16
5 1.77
22.
835
4.587
2.559
5/16-18x0.43
2.165
(A) 2.5594 holes M6x0.43
1.693
Input Bore
For all ratio 1/7-1/102
5.00
0
2.1652.323
M6x0.390.1875
0.625
0.72
0
2.598
1.77
2
2.1850.24
0.33
2.283
3.4250.39
2.36
81
3.563
ø4.3
312.
3642
3.93
7
0.7870.43
3
0.906
5.11
8
0.866
0.123.327
0.1875
0.7500.83
0
1.594
1.125
1.929
F2SB
tA R/L
øF
A
CB
D
S45 Nema Flanges øF A
56C 6.5” 3.846”
S45
11.0pounds
Gearbox Weight
S50output Speed (RPM)
Ratio Motor Power (HP)
output torque (in-lbs)
Service Factor
oHL nom. torque (in-lbs)
Reducer Part number*
Gearmotor Part number*
250 72 413 1.2
256 478 RS50-0007-HSB2S-WGS50-0007-HSB2S-WAG3B
1 207 2.3 GS50-0007-HSB2S-WAE3B
175 101.5 432 1.2
270 522 RS50-0010-HSB2S-WGS50-0010-HSB2S-WAE3B
1 288 1.8 GS50-0010-HSB2S-WAE3B
125 141 398 1.4
315 575 RS50-0014-HSB2S-WGS50-0014-HSB2S-WAE3B
0.5 199 2.9 GS50-0014-HSB2S-WAC3B
97.2 181 486 1.1
337 522 RS50-0018-HSB2S-WGS50-0018-HSB2S-WAE3B
0.5 243 2.1 GS50-0018-HSB2S-WAC3B
67.3 260.75 485 1.2
382 558 RS50-0026-HSB2S-WGS50-0026-HSB2S-WAD3B
0.5 323 1.7 GS50-0026-HSB2S-WAC3B
58.3 300.75 567 1.1
382 611 RS50-0030-HSB2S-WGS50-0030-HSB2S-WAD3B
0.5 378 1.6 GS50-0030-HSB2S-WAC3B
40.7 430.5 511 1.1
427 575 RS50-0043-HSB2S-WGS50-0043-HSB2S-WAC3B
0.25 256 2.3 GS50-0043-HSB2S-WAA3B
29.2 600.33 414 1.3
427 522 RS50-0060-HSB2S-WGS50-0060-HSB2S-WAB3B
0.25 313 1.7 GS50-0060-HSB2S-WAA3B
25.7 680.33 461 1.1
427 487 RS50-0068-HSB2S-WGS50-0068-HSB2S-WAB3B
0.25 349 1.4 GS50-0068-HSB2S-WAA3B
21.9 80 0.25 389 1.2 562 478 RS50-0080-HSB2S-W GS50-0080-HSB2S-WAA3B
17.5 100 0.25 450 1.0 562 434 RS50-0100-HSB2S-W GS50-0100-HSB2S-WAA3B
Notes: All units shown are standard configuration. Input motor, output shaft and mounting options are available. Motor Specification: 230/460 VAC 60/50Hz, 3PH 1800 RPM Nom. - inverter duty *NEMA Input Sizes: W = 56CX = 143/5TCY = 182/4TC
37
Stainless Steel Integral HP Worm Speed Reducer0.25 - 2HP, 434 - 611 in-lbs, 17.5 - 250RPM
· Stainless steel housing for food processing, medical and pharmaceutical applications · Interchangeability with most global manufacturers
S50
tECHnICAL DAtA
38
DRAWInGSBasic Gearbox
Output FlangeModular Base
Torque Arm Output Shaft Insert
Mounting Hole Positions
Standard Hollow Shaft
Side (A) Mounting Holes
Input Bore
For all ratio 1/7-1/102
5.55
1(A)
1.18
14.016
1.8112.
362
2.953
2.36
21.
969
3.18
9
5.276
3.189
5/16-18x0.43
2.677
(A)
M6x0.35-60°6 holes 3.189
2.205
5.55
1
2.6772.323
M6x0.39
2.846
1.96
9
2.362 0.1875
0.625
0.72
0
0.24
0.41
2.283
3.5430.39
2.76
18
3.878
ø4.8
43
2.76
38
4.33
1
1.1810.43
1.220
5.51
2
0.787
0.16
3.882
0.25
1.0001.11
0
1.929
1.250
2.130
F2SB
tA R/L
øF
A
CB
D
Hollow Shaft B C D
Imperial 1.000” 1.114” 0.25”
Metric (mm) 25 28.3 8
S50 Nema Flanges øF A
56C 6.5” 4.004”
S50
16.1pounds
Gearbox Weight
S63output Speed (RPM)
Ratio Motor Power (HP)
output torque (in-lbs)
Service Factor
oHL nom. torque (in-lbs)
Reducer Part number*
Gearmotor Part number*
250 72 419 2.5
385 1053 RS63-0007-HSB2S-XGS63-0007-HSB2S-XAG3B
1 209 5 GS63-0007-HSB2S-XAE3B
175 102 583 1.9
404 1133 RS63-0010-HSB2S-XGS63-0010-HSB2S-XAG3B
1 292 3.9 GS63-0010-HSB2S-XAE3B
116.7 152 854 1.4
450 1159 RS63-0015-HSB2S-XGS63-0015-HSB2S-XAG3B
1 427 2.7 GS63-0015-HSB2S-XAE3B
92.1 192 1068 1.1
517 1159 RS63-0019-HSB2S-XGS63-0019-HSB2S-XAG3B
1 534 2.2 GS63-0019-HSB2S-XAE3B
72.9 241.5 972 1.2
562 1195 RS63-0024-HSB2S-XGS63-0024-HSB2S-XAE3B
1 648 1.8 GS63-0024-HSB2S-XAE3B
58.3 301.5 1199 1
562 1230 RS63-0030-HSB2S-XGS63-0030-HSB2S-XAE3B
1 800 1.5 GS63-0030-HSB2S-XAE3B
48.6 361 882 1.4
674 1239 RS63-0036-HSB2S-XGS63-0036-HSB2S-XAE3B
0.5 441 2.8 GS63-0036-HSB2S-WAC3B
38.9 451 1070 1.1
674 1142 RS63-0045-HSB2S-XGS63-0045-HSB2S-XAE3B
0.5 535 2.1 GS63-0045-HSB2S-WAC3B
26.1 670.5 724 1.4
674 1044 RS63-0067-HSB2S-WGS63-0067-HSB2S-WAC3B
0.25 362 2.9 GS63-0067-HSB2S-WAA3B
21.9 800.5 821 1.2
854 1000 RS63-0080-HSB2S-WGS63-0080-HSB2S-WAC3B
0.25 411 2.4 GS63-0080-HSB2S-WAA3B
18.6 940.5 880 1.1
854 1000 RS63-0094-HSB2S-WGS63-0094-HSB2S-WAC3B
0.25 440 2.3 GS63-0094-HSB2S-WAA3B
Notes: All units shown are standard configuration. Input motor, output shaft and mounting options are available. Motor Specification: 230/460 VAC 60/50Hz, 3PH 1800 RPM Nom. - inverter duty *NEMA Input Sizes: W = 56CX = 143/5TCY = 182/4TC Motors 1HP and greater meet EISA efficiency requirements.
39
Stainless Steel Integral HP Worm Speed Reducer0.25 - 2HP, 1000 - 1230 in-lbs, 18.6 - 250RPM
· Stainless steel housing for food processing, medical and pharmaceutical applications · Interchangeability with most global manufacturers
S63
tECHnICAL DAtA
40
DRAWInGSBasic Gearbox
Output FlangeModular Base
Torque Arm Output Shaft Insert
Mounting Hole Postions
Standard Hollow Shaft
Side (A) Mounting Holes
Input Bore
For all ratio 1/7-1/102
6.89
0(A)
1.81
15.040
2.5203.
622
3.622
2.95
32.
480
3.93
7
6.378
4.724
3.031(A)
4.724
3/8-16x0.67
4 holes M8x0.43
2.520
M8x0.553.150
0.1875
0.875
0.97
8
6.89
0
3.0313.583
2.48
0
3.110 0.24
0.41
2.205
5.9060.47
4.53
35
4.567
ø6.8
90
4.53
54
5.11
8
1.9490.43
1.988
6.29
9
0.787
e1m1
b1
o1
t2
2.854
1.250
c1
d1
b1 c1 d1 e1 m1 t2 o1
Standard 0.25 2.240 1.125 0.197 4.799 1.23 5/16-18
F2SB
tA R/L
øF
A
CB
D
Hollow Shaft B C D
Imperial 1.125” 1.245” 0.25”
Metric (mm) 25 28.3 8
S63 Nema Flanges øF A
56C - 143/5TC 6.5” 4.291”
S63
32.2pounds
Gearbox Weight
Stainless Steel Integral HP Worm Speed Reducer0.5 - 5HP, 2036 - 2921 in-lbs, 18.2 - 250RPM
· Stainless steel housing for food processing, medical and pharmaceutical applications · Interchangeability with most global manufacturers
S85
tECHnICAL DAtA
S85output Speed
Ratio Motor Power (HP)
output torque
Service Factor
oHL nom. torque (in-lbs)
Reducer Part number*
Gearmotor Part number*
250 75 1109 2.0
529 2168 RS85-0007-HSB2S-YGS85-0007-HSB2S-YAJ3B
3 666 3.3 GS85-0007-HSB2S-YAH3B
175 105 1441 1.7
562 2390 RS85-0010-HSB2S-YGS85-0010-HSB2S-YAJ3B
3 864 2.8 GS85-0010-HSB2S-YAH3B
125 145 1967 1.3
652 2567 RS85-0014-HSB2S-YGS85-0014-HSB2S-YAJ3B
3 1180 2.2 GS85-0014-HSB2S-YAH3B
87.5 203 1707 1.5
674 2478 RS85-0020-HSB2S-YGS85-0020-HSB2S-YAH3B
1.5 854 2.9 GS85-0020-HSB2S-XAE3B
62.5 283 2269 1.3
787 2921 RS85-0028-HSB2S-YGS85-0028-HSB2S-YAH3B
1.5 1135 2.6 GS85-0028-HSB2S-XAE3B
46.1 383 2915 1.0
899 2832 RS85-0038-HSB2S-YGS85-0038-HSB2S-YAH3B
1.5 1458 1.9 GS85-0038-HSB2S-XAE3B
33.7 522 2472 1.0
899 2434 RS85-0052-HSB2S-XGS85-0052-HSB2S-XAG3B
1 1236 2.0 GS85-0052-HSB2S-XAD3B
26.1 671.5 2353 1.0
899 2434 RS85-0067-HSB2S-XGS85-0067-HSB2S-XAE3B
1 1569 1.6 GS85-0067-HSB2S-XAD3B
23.7 741.5 2319 1.0
1124 2257 RS85-0074-HSB2S-XGS85-0074-HSB2S-XAE3B
1 1546 1.5 GS85-0074-HSB2S-XAD3B
18.2 961 1833 1.1
1124 2036 RS85-0096-HSB2S-XGS85-0096-HSB2S-XAD3B
0.5 916 2.2 GS85-0096-HSB2S-WAC3B
Notes: All units shown are standard configuration. Input motor, output shaft and mounting options are available. Motor Specification: 230/460 VAC 60/50Hz, 3PH 1800 RPM Nom. - inverter duty *NEMA Input Sizes: W = 56CX = 143/5TCY = 182/4TC Motors 1HP and greater meet EISA efficiency requirements.
41
DRAWInGSBasic Gearbox
42
Output FlangeModular Base
Torque Arm Output Shaft Insert
Mounting Hole Postions
(A)
2.08
76.457
3.228
4.17
3
5.315
(A)3.228 7/16-14x0.75
Side (A) Mounting Holes
Input Bore
For all ratio 1/7-1/102
0.25
1.125
1.25
0
9.13
4
4.0554.134
M8x0.55
4.331
3.34
6
3.858 52°
0.24
0.51
3.189
6.9290.51
5.98
43
5.846
ø8.0
71
5.98
66
6.29
9
2.1260.83
2.165
7.67
7
1.024
0.206.260
0.375
1.5001.65
8
3.051
1.750
3.406
F2SB
tA R/L
øF
Standard Hollow Shaft
9.13
4
4.724
3.72
03.
346
5.41
3M8 x 0.43
4.055
6 holes 5.315
A
CB
D
Hollow Shaft B C D
Imperial 1.500” 1.670” 0.375”
Metric (mm) 35 38.3 10
S85 Nema Flanges øF A
56C - 143/5TC 6.5” 4.823”
182/4TC 8.88” 5.528”
8.189
S85
51.4pounds
Gearbox Weight
B7B3 B8B6 V5 V6
oil Quantity (oz.) Per Mounting PositionB3 B6 B7 B8 V5 V6
S45 5.28 5.28 7.04 5.28 5.28 5.28S50 7.74 7.74 9.85 7.74 7.74 7.74S63 21.1 21.1 28.9 21.1 21.1 21.1S85 49.3 49.3 59.8 49.3 49.3 49.3
oil Quantity (oz.) Per Mounting Position
LuBRICAtIon
oVERHunG LoAD · Overhung load generated by external transmissions keyed onto input and/or output shafts
43
FR
FR
Integral HP Worm Speed Reducer
Worm Reducer SSERIES
M Output Torqued diameter of driving elementFK Coefficient Factor
1.15 Gearwheels1.25 Chain sprockets1.75 Narrow v-belt pulley 2.50 Flat-belt pulley
d [mm]fK
M [Nm] 2000FR [N] =
d [in]fK
M [lb in] 8.9FR [N] =
44
Q/S45 Q/S50 Q/S63 Q/S85
>25° 7 7 712° - 25° 10/14 7/10 10/15 10/14/20/228° - 12° 21 14/18 19/245° - 8° 28 26/36 30/36 28/38/46/523° - 5° 37/46/68 43/60/68 45/60/67/80 67/74/961° - 3° 70/102 80/100 94
>25° · Totally reversible
12° - 25°· Statically reversible· Quick return· Dynamically reversible
8° - 12°· Variable static non-reversing quick return in case of vibrations · Dynamically reversible
5° - 8°· Static non-reversing return in case of vibrations · bad dynamic reversing
3° - 5°· Statically non-reversing return in case of vibrations · Low dynamic reversing*
1° - 3° · Statically non-reversing no return· Low dynamic reversing*
*Elimination of backdrive not guaranteed. Where required, an external break is recommended.
A
60
100
80
0
20
40C°
1 Time (h)
0/80% of Power
100% Power SF=1
Thermal limit with intermittant duty.Thermal limit B
1 Time (h)
60
100
80
0
20
40C°
C
T1 TT 1T
60
100
80
0
20
40C°
1 Time (h)
D
100% Power100% of Power
50% of Power 50% of Power
Time (h)
60
100
80
0
20
40C°
1
A - Temperature Increase depending on operating time. Final temperature is based on these variables: · Installed power and percentage of use · Ambient temperature · Lubrication · Cooling Method · Input speed
B - The temperature increase curve is similar to continuous duty. Peak is reached in 20/30 minutes using 100% of the power. The gearbox can be stopped at any point on this curve. Follow cooling curve (graph B) where shape depends on ambient operating temperature.
Thermal limit with intermittant duty. Thermal limit with intermittant duty.
BACk DRIVE· With worm gearboxes it is important to consider the several levels of reversibility of the worm gear set, in order to guarantee the correct selection in applications where these requirements are essential for the operation of the machine. The table belows shows the different levels of back drive for worm gearboxes according to helix angle ß and reduction ratio i.
tHERMAL LIMIt· Due to the internal design, worm gearboxes transform their installed power into heat which is dissipated through the housing. Typical safety temperature ranges are between 80° - 100°C. See graphs below:
· C & D - Should gearbox have several start/stop cycles, final temperature will depend on start/stop times and frequency. Service factors given in this catalog are based on intermittent duty.
· Gearmotors with 2800 min-1 input speed are tolerated at intermittent duty only, due to temperature rise from input rotation speed.
H
Hollow Output Shaft
L
Single Output Shaft
22 B33 B64 B75 B86 V57 V6
-- Inch (Standard)A Metric
Inch (Standard)S45
Ø0.75S50
Ø1.00S63
Ø1.125S85
Ø1.500
MetricS45
Ø18S50
Ø25S63
Ø25S85
Ø35
Integral HP Worm Speed Reducer
HoLLoW oP RAtIo - outPut SHAFt MountInG
MountInGPoSItIontYPE SIZE
RR- ReducerG-Gearmotor
0018See Ratio table for Selection
S45 S50 S63 S857 7 7 710 10 10 1014 14 15 1421 18 19 2028 26 24 2837 30 30 3846 43 45 5260 60 - 6770 68 67 74102 80 80 96
100 94
7:1 = 0007 18:1 = 0018 96:1 = 0096
B3
B7
B6
B8
V5
V6
Worm Reducers SSERIES
HH HollowR Right Ext.L Left Ext.
SBSB Standard
BaseF2 OP Flange 2TA Torque Arm
SB
F2
tA
MOUNTING ACCESSORIES
SHIPPED LOOSE WITH UNIT
45
S45StainlessS45S50S63S85
ø
PRoDuCt SELECtIon tABLES
LuBRICAtIon -MotoR
Mount StYLE MotoR/PoWER tYPE noM. MotoR RPM MotoR PoSItIon
BA 270°B 0°C 90°
D 180°
32 12003 18004 3600
SS StandardF Food
Grade
StandardShell Omala S4 WE 320
Food GradeMobile
Glygoyle 320
ALL OPTIONS ARE HIGH
GRADE SYNTHETIC
OIL
C
A
D
B
46
WNemaW 56C (Ø = 6.5”)X 143/5TC
(Ø = 6.5”)Y 182/4TC
(Ø = 8.875”)
ø
Flange
SAMPLE PART NUMBERS: RS50-0018-HSB2F-W, GS63-0010-HF23F-XSQ3C
(StAnDARD)
ADPowerWash Xt Washdown (3PH, C-Face, Footless)SA White Epoxy (IP55) 0.25HP, 208-230/460V
SB White Epoxy (IP55) 0.33HP, 208-230/460V
SC White Epoxy (IP55) 0.5HP, 208-230/460V
SD White Epoxy (IP55) 0.75HP, 208-230/460V
SE White Epoxy (IP55) 1HP, 208-230/460V
SF White Epoxy (IP55) 1.5HP, 208-230/460V
SG White Epoxy (IP55) 2HP, 208-230/460V
SH White Epoxy (IP55) 3HP, 208-230/460V
SJ White Epoxy (IP55) 5HP, 208-230/460V
PowerWash SXt Washdown (3PH, C-Face, Footless)SK Stainless Steel (IP55) 0.33HP, 208-230/460V
SL Stainless Steel (IP55) 0.5HP, 208-230/460V
SM Stainless Steel (IP55) 0.75HP, 208-230/460V
SN Stainless Steel (IP55) 1HP, 208-230/460V
SP Stainless Steel (IP55) 1.5HP, 208-230/460V
SQ Stainless Steel (IP55) 2HP, 208-230/460V
PowerWash Extreme Washdown (3PH, C-Face, Footless)
ST Stainless Steel (BISSC, IP66) 0.5HP, 208-230/460V
SU Stainless Steel (BISSC, IP66) 0.75HP, 208-230/460V
SV Stainless Steel (BISSC, IP66) 1HP, 208-230/460V
SW Stainless Steel (BISSC, IP66) 1.5HP, 208-230/460V
SX Stainless Steel (BISSC, IP66) 2HP, 208-230/460V
SEE PAGE 49 FOR MORE MOTOR OPTIONS
· Rated 60/50 hertz, 190/380 or 380 volt, at next lower horsepower (as noted)· 1.15 Service Factor (except as noted)· Rolled steel 56-145T frame motors accept brake kits· UL Recognized and CSA Certified· Inverter Duty Rated
General Purpose, three Phase
tECHnICAL DAtA
C-Face FootlessHP RPM VoLtS FRAME MoDEL no. noM.
EFF.F.L. AMPS WEIGHt DIM.
“C”DIM. “P”
1/4 1800 208-230/460 56C 150-503-7004 67.4 1.1-1.2/0.6 16 10.33 6.4
1/3 1800 208-230/460 56C 150-503-7014 68.8 1.5-1.6/0.8 16 10.60 5.6
1/2 1800 208-230/460 56C 150-503-7024 76.1 2.1-2.2/1.1 17 10.93 5.6
3/4 1800 208-230/460 56C 150-503-7034 78.9 2.8-2.8/1.4 20 11.36 5.6
1 1800 208-230/460 56C 150-503-7044 79.2 3.6-3.8/1.9 46 14.15 6.6
1 1/2 1800 208-230/460 56C 150-503-7054 81.7 4.7-4.4/2.2 47 14.65 6.6
2 1800 208-230/460 56C 150-503-7064 83.6 6.2-5.8/2.9 50 15.15 6.6
3 1800 208-230/460 182tC 150-503-6024* 87.5 8.8-8.4/4.2 76 14.47 8.4
5 1800 208-230/460 184tC 150-503-6034* 88.5 13.8-12.6/6.3 80 14.97 8.4
47
*Nema Premium Efficiency Rated
48
· Heavy gauge steel constructions· Suitable for horizontal or vertical mounting· Economical split phase or capacitor start designs, as noted· UL Recognized and CSA Certified
General Purpose, Single Phase
tECHnICAL DAtA
C-Face FootlessHP RPM VoLtS FRAME oVER
LoADMoDEL no. F.L. AMPS WEIGHt DIM.
“C” DIM. “P”
1/4 1800 115/230 56C nonE 150-505-6004 5.4/2.7 16 10.30 5.6
1/3 1800 115/230 56C nonE 150-505-6014 6.0/3.0 19 10.93 5.6
1/2 1800 115/230 56C nonE 150-505-6034 8.6/4.3 21 11.01 6.4
3/4 1800 115/230 56C nonE 150-505-6054 11.0/5.5 31 11.84 6.4
1 1800 115/230 56C nonE 150-505-6074 13.2/6.6 36 12.97 6.4
1 1/2 1800 115/208-230 56C nonE 150-505-6094 14.5/7.1-7.3 44 13.69 6.4
· Brake has manual wear adjustment up to 25 lb-ft. for longer pad life· Stearns brakes, 56 series through 25 lb-ft., 87 series above 35 lb-ft. and larger· Brake leads routed through motor conduit box (TENV only)· Universal mounting up to 15 lb-ft.· Motor can be operated 10:1 variable torque· 1.15 Service Factor, 1.0 Service Factor where footnoted · Inverter Duty Rated
Brake Motors, three Phase
tECHnICAL DAtA
C-Face FootedHP RPM VoLtS FRAME MoDEL no. F.L. AMPS BRAkE
RAtInG (lb-ft)
WEIGHt DIM. “C”
DIM. “P”
1/2 1800 208-230/460 56C 150-503-8004 2.3-2.4/1.2 3 32 16.23 6.5
3/4 1800 208-230/460 56C 150-503-8014 2.9-3.0/1.5 6 33 16.23 6.5
1 1800 208-230/460 56C 150-503-8024 3.5-3.6/1.8 6 40 18.81 6.5
1 1/2 1800 208-230/460 145HC 150-503-8044 4.8-4.8/2.4 10 45 18.76 6.5
2 1800 208-230/460 145tC 150-503-8054 6.0-5.8/2.9 10 63 20.32 6.5
3 1800 230/460 182tC 150-503-8064 8.0/4.0 15 100 19.68 9.75
5 1800 208-230/460 184tC 150-503-8074 13.8-12.4/6.2 25 115 20.68 9.75
49
DRAWInGS
50
Typical C-Face Motor
Frame D E 2F H u AA AH AJ Ak BA BB (MIn) BD (MAX) BF
48 3.00 2.12 2.75 .34 SLOT .5000 1/2 1.69 3.750 3.000 2.50 .13 5.62 1/4-20
56 3.50 2.44 3.00 .34 SLOT .6250 1/2 2.06 5.875 4.500 2.75 .13 6.50 3/8-16
56H 3.50 2.44 5.00 .34 SLOT .6250 1/2 2.06 5.875 4.500 2.75 .13 6.50 3/8-16
143t 3.50 2.75 4.00 .34 .8750 3/4 2.12 5.875 4.500 2.25 .13 6.50 3/8-16
145t 3.50 2.75 5.00 .34 .8750 3/4 2.12 5.875 4.500 2.25 .13 6.50 3/8-16
182 4.5 3.75 4.50 .41 .8750 3/4 2.12 5.875 4.500 2.75 .13 6.50 3/8-16
184 4.5 3.75 5.50 .41 .8750 3/4 2.12 5.875 4.500 2.75 .13 6.50 3/8-16
182t 4.5 3.75 4.50 .41 1.125 3/4 2.62 7.250 8.500 2.75 .25 9.00 1/2-13
184t 4.5 3.75 5.50 .41 1.125 3/4 2.62 7.250 8.500 2.75 .25 9.00 1/2-13
213 5.25 4.25 5.50 .41 1.125 1 2.75 7.250 8.500 3.50 .25 9.00 1/2-13
215 5.25 4.25 7.00 .41 1.125 1 2.75 7.250 8.500 3.50 .25 9.00 1/2-13
213t 5.25 4.25 5.50 .41 1.125 1 3.12 7.250 8.500 3.50 .25 9.00 1/2-13
215t 5.25 4.25 7.00 .41 1.125 1 3.12 7.250 8.500 3.50 .25 9.00 1/2-13
BB BD
FRAME D E 2F H U N-W AA AH AJ AK BA (MIN) (MAX) BF
48 3.00 2.12 2.75 .34 SLOT .5000 1.50 1/2 1.69 3.750 3.000 2.50 .13 5.62 1/4-20
56 3.50 2.44 3.00 .34 SLOT .6250 1.88 1/2 2.06 5.875 4.500 2.75 .13 6.50 3/8-16
56H 3.50 2.44 5.00 .34 SLOT .6250 1.88 1/2 2.06 5.875 4.500 2.75 .13 6.50 3/8-16
143T 3.50 2.75 4.00 .34 .8750 2.25 3/4 2.12 5.875 4.500 2.25 .13 6.50 3/8-16
145T 3.50 2.75 5.00 .34 .8750 2.25 3/4 2.12 5.875 4.500 2.25 .13 6.50 3/8-16
182 4.50 3.75 4.50 .41 .8750 2.25 3/4 2.12 5.875 4.500 2.75 .13 6.50 3/8-16
184 4.50 3.75 5.50 .41 .8750 2.25 3/4 2.12 5.875 4.500 2.75 .13 6.50 3/8-16
182T 4.50 3.75 4.50 .41 1.125 2.75 3/4 2.62 7.250 8.500 2.75 .25 9.00 1/2-13
184T 4.50 3.75 5.50 .41 1.125 2.75 3/4 2.62 7.250 8.500 2.75 .25 9.00 1/2-13
213 5.25 4.25 5.50 .41 1.125 3.00 1 2.75 7.250 8.500 3.50 .25 9.00 1/2-13
215 5.25 4.25 7.00 .41 1.125 3.00 1 2.75 7.250 8.500 3.50 .25 9.00 1/2-13
213T 5.25 4.25 5.50 .41 1.375 3.38 1 3.12 7.250 8.500 3.50 .25 9.00 1/2-13
215T 5.25 4.25 7.00 .41 1.375 3.38 1 3.12 7.250 8.500 3.50 .25 9.00 1/2-13
254U 6.25 5.00 8.25 .53 1.375 3.75 1-1/4 3.50 7.250 8.500 4.25 .25 10.00 1/2-13
256U 6.25 5.00 10.00 .53 1.375 3.75 1-1/4 3.50 7.250 8.500 4.25 .25 10.00 1/2-13
254T 6.25 5.00 8.25 .53 1.625 4.00 1-1/4 3.75 7.250 8.500 4.25 .25 10.00 1/2-13
256T 6.25 5.00 10.00 .53 1.625 4.00 1-1/4 3.75 7.250 8.500 4.25 .25 10.00 1/2-13
284U 7.00 5.50 9.50 .53 1.625 4.88 1-1/2 4.62 9.000 10.500 4.75 .25 11.25 1/2-13
286U 7.00 5.50 11.00 .53 1.625 4.88 1-1/2 4.62 9.000 10.500 4.75 .25 11.25 1/2-13
284T 7.00 5.50 9.50 .53 1.875 4.62 1-1/2 4.38 9.000 10.500 4.75 .25 11.25 1/2-13
286T 7.00 5.50 11.00 .53 1.875 4.62 1-1/2 4.38 9.000 10.500 4.75 .25 11.25 1/2-13
284TS 7.00 5.50 9.50 .53 1.625 3.25 1-1/2 3.00 9.000 10.500 4.75 .25 11.25 1/2-13
286TS 7.00 5.50 11.00 .53 1.625 3.25 1-1/2 3.00 9.000 10.500 4.75 .25 11.25 1/2-13
324U 8.00 6.25 10.50 .66 1.875 5.62 2 5.38 11.000 12.500 5.25 .25 14.00 5/8-11
326U 8.00 6.25 12.00 .66 1.875 5.62 2 5.38 11.000 12.500 5.25 .25 14.00 5/8-11
324T 8.00 6.25 10.50 .66 2.125 5.25 2 5.00 11.000 12.500 5.25 .25 14.00 5/8-11
326T 8.00 6.25 12.00 .66 2.125 5.25 2 5.00 11.000 12.500 5.25 .25 14.00 5/8-11
324TS 8.00 6.25 10.50 .66 1.875 3.75 2 3.50 11.000 12.500 5.25 .25 14.00 5/8-11
326TS 8.00 6.25 12.00 .66 1.875 3.75 2 3.50 11.000 12.500 5.25 .25 14.00 5/8-11
364U 9.00 7.00 11.25 .66 2.125 6.38 2-1/2 6.12 11.000 12.500 5.88 .25 14.00 5/8-11
365U 9.00 7.00 12.25 .66 2.125 6.38 2-1/2 6.12 11.000 12.500 5.88 .25 14.00 5/8-11
364T 9.00 7.00 11.25 .66 2.375 5.88 2-1/2 5.62 11.000 12.500 5.88 .25 14.00 5/8-11
365T 9.00 7.00 12.25 .66 2.375 5.88 2-1/2 5.62 11.000 12.500 5.88 .25 14.00 5/8-11
364TS 9.00 7.00 11.25 .66 1.875 3.75 2-1/2 3.50 11.000 12.500 5.88 .25 14.00 5/8-11
365TS 9.00 7.00 12.25 .66 1.875 3.75 2-1/2 3.50 11.000 12.500 5.88 .25 14.00 5/8-11
404U 10.00 8.00 12.25 .81 2.375 7.12 3 6.88 11.000 12.500 6.62 .25 15.50 5/8-11
405U 10.00 8.00 13.75 .81 2.375 7.12 3 6.88 11.000 12.500 6.62 .25 15.50 5/8-11
404T 10.00 8.00 12.25 .81 2.875 7.25 3 7.00 11.000 12.500 6.62 .25 15.50 5/8-11
405T 10.00 8.00 13.75 .81 2.875 7.25 3 7.00 11.000 12.500 6.62 .25 15.50 5/8-11
404TS 10.00 8.00 12.25 .81 2.125 4.25 3 4.00 11.000 12.500 6.62 .25 15.50 5/8-11
405TS 10.00 8.00 13.75 .81 2.125 4.25 3 4.00 11.000 12.500 6.62 .25 15.50 5/8-11
444U 11.00 9.00 14.50 .81 2.875 8.62 3 8.38 14.000 16.000 7.50 .25 18.00 5/8-11
445U 11.00 9.00 16.50 .81 2.875 8.62 3 8.38 14.000 16.000 7.50 .25 18.00 5/8-11
444T 11.00 9.00 14.50 .81 3.375 8.50 3 8.25 14.000 16.000 7.50 .25 18.00 5/8-11
445T 11.00 9.00 16.50 .81 3.375 8.50 3 8.25 14.000 16.000 7.50 .25 18.00 5/8-11
444TS 11.00 9.00 14.50 .81 2.375 4.75 3 4.50 14.000 16.000 7.50 .25 18.00 5/8-11
445TS 11.00 9.00 16.50 .81 2.375 4.75 3 4.50 14.000 16.000 7.50 .25 18.00 5/8-11
447T 11.00 9.00 20.00 .81 3.375 8.50 3 8.25 14.000 16.000 7.50 .25 18.00 5/8-11
449T 11.00 9.00 25.00 .81 3.375 8.50 3 8.25 14.000 16.000 7.50 .25 18.00 5/8-11
447TS 11.00 9.00 20.00 .81 2.375 4.75 4 NPT 4.50 14.000 16.000 7.50 .25 18.00 5/8-11
449TS 11.00 9.00 25.00 .81 2.375 4.75 4 NPT 4.50 14.000 16.000 7.50 .25 18.00 5/8-11
NEMA Quick Reference Dimensional Chart
Typical C-Face Motor Typical Rigid Base Motor
NEMA BA C-Face Dimensions
143-5TC 2-3/4
182-4TC 3-1/2
213-5TC 4-1/4
254-6TC 4-3/4
Refer to your Marathon Electric
catalog for “C” Dimensions.
Contact your Marathon Electric sales
representative for “AB”, “O”, & “P” Dimensions.
Marathon Electric Manufacturing Corporation
SB300/6039M/BH&SK/REV12-07/15M-DBH
See motor data tables for “C” and “P” dimensions.
IEC AC Motors, three Phase
tECHnICAL DAtA
B14 (C-Face)HP kW RPM
60/50 HZ60 HZVoLtS
50 HZVoLtS
IECFRAME
MoDEL no. C.t. SPEED
RAnGE*
noM.EFF.
60 HZF.L.
AMPS
WEIGHt IEC “L” DIM. (MM)
1/4 .18 1800/1500 230/460 200/400 63C 150-504-2004 20:1 68.0 1.0/0.5 11 217
1/2 .37 1800/1500 230/460 200/400 71C 150-504-2024 20:1 74.0 1.8/.9 14 282
3/4 .55 1800/1500 230/460 200/400 80C 150-504-2034 20:1 74.0 2.5/1.25 18 282
1 .75 1800/1500 230/460 200/400 80C 150-504-2044 20:1 85.5 3.0/1.5 30 302
1 1/2 1.1 1800/1500 230/460 200/400 90SC 150-504-2054 20:1 86.5 4.6/2.3 37 320
2 1.5 1800/1500 230/460 200/400 90LC 150-504-2064 20:1 86.5 5.8/2.9 38 320
3 2.2 1800/1500 230/460 200/400 100L P150-125-2074 20:1 89.5 3.6 84 415
5 1/2 4 1800/1500 230/460 200/400 112M P150-125-2084 20:1 89.5 14.0/7.0 104 410
51
the IEC motor is not only designed to international standards but meets nEMA performance and efficiency standards making it suitable for requirements worldwide.
· Meets IE3 European and NEMA Premium® effeciencies· Aluminum (63-90 frame) or Cast Iron (100-250 frame) construction· Nameplated 60/50 hertz at same HP (except as noted)· Class F Insulation, Class B rise @ rated KW· IP55 weatherproof enclosure· Rotateable/Removable Base (63 - 90 frame)· 10:1 Variable Torque, Constant Torque speed range as noted· Top Mounted/Oversized gasketed terminal box· Meets IEEE45, IEC60092 & USCG CFR46 Marine Duty· 1.15 Service Factor on 60 Hz sine wave, 1.0 SF on VFD· IEC Design “N” with NEMA “B” Torques· Inverter Duty Rated· Terminal Blocks, Stud Type, Zero Creepage· Meets IEC 34 electrical standards· Meets IEC 72 dimensions and tolerances· CE Marked· 1 year warranty
DRAWInGS
52
FrameMounting Shaft General B5 (FF) Flange B14 (Ft) Face
A B C H AB k D E F G ED DH AC AD HD M n P S t LA M n P S t LA
63 100 80 40 63 119 7 11 23 4 8.5 10 M4 x 10 126 - 169 115 95 140 10 3.0 7 75 60 90 M5 2.5 7
71 112 90 45 71 131 7 14 30 5 11.0 20 M5 x 12.5 140 - 186 130 110 160 10 3.5 7 85 70 105 M6 2.5 9
80 125 100 50 80 157 10 19 40 6 15.5 25 M6 x 16 158 132 212 165 130 200 12 3.5 12 100 80 120 M6 3.0 9
90S 140 100 56 90 174 10 24 50 8 20.0 32 M8 x 19 178 140 230 165 130 200 12 3.5 12 115 95 140 M8 3.0 9
90L 140 125 56 90 174 10 24 50 8 20.0 32 M8 x 19 178 140 230 165 130 200 12 3.5 12 115 95 140 M8 3.0 9
100L 160 140 63 100 205 12 28 60 8 24.0 40 M10 x 22 215 178 278 215 180 250 15 4.0 11 130 110 160 M8 3.5 14
112M 190 140 70 112 245 12 28 60 8 24.0 40 M10 x 22 215 190 302 215 180 250 15 4.0 12 130 110 160 M8 3.5 11
B3 Foot-Mounted (Ridge Base)
FT Face B14 Mount FRAME
Mounting Shaft General B5 (FF) Flange B14 (FT) Face
A B C H AB K D E F G ED DH AC AD HD M N P S T LA M N P S T LA
63 100 80 40 63 119 7 11 23 4 8.5 10 M4 x 10 126 – 169 115 95 140 10 3.0 7 75 60 90 M5 2.5 7
71 112 90 45 71 131 7 14 30 5 11.0 20 M5 x 12.5 140 – 186 130 110 160 10 3.5 7 85 70 105 M6 2.5 9
80 125 100 50 80 157 10 19 40 6 15.5 25 M6 x 16 158 132 212 165 130 200 12 3.5 12 100 80 120 M6 3.0 9
90S 140 100 56 90 174 10 24 50 8 20.0 32 M8 x 19 178 140 230 165 130 200 12 3.5 12 115 95 140 M8 3.0 9
90L 140 125 56 90 174 10 24 50 8 20.0 32 M8 x 19 178 140 230 165 130 200 12 3.5 12 115 95 140 M8 3.0 9
100L 160 140 63 100 205 12 28 60 8 24.0 40 M10 x 22 215 178 278 215 180 250 15 4.0 11 130 110 160 M8 3.5 14
112M 190 140 70 112 245 12 28 60 8 24.0 40 M10 x 22 220 190 302 215 180 250 15 4.0 12 130 110 160 M8 3.5 11
132S 216 140 89 132 280 12 38 80 10 33.0 56 M12 x 28 275 210 342 265 230 300 15 4.0 12 165 130 200 M10 3.5 14
132M 216 178 89 132 280 12 38 80 10 33.0 56 M12 x 28 275 210 342 265 230 300 15 4.0 12 165 130 200 M10 3.5 14
160M 254 210 108 160 325 15 42 110 12 37.0 80 M16 x 36 325 254 414 300 250 350 19 5.0 13 215 180 250 M12 4.0 13
160L 254 254 108 160 325 15 42 110 12 37.0 80 M16 x 36 325 254 414 300 250 350 19 5.0 13 215 180 250 M12 4.0 13
180M 279 241 121 180 335 15 48 110 14 42.5 80 M16 x 36 360 310 490 300 250 350 19 5.0 15
180L 279 279 121 180 335 15 48 110 14 42.5 80 M16 x 36 360 310 490 300 250 350 19 5.0 15
200L 318 305 133 200 395 19 55 110 16 49.0 100 M20 x 42 400 340 540 350 300 400 19 5.0 19.5
55*/ 110*/ 16*/ 49*/ 100*/
225S 356 286 149 225 435 19 60 140 18 53 125
M20 x 42 445 414 639 400 350 450 19 5.0 21.0
55*/ 110*/ 16*/ 49*/ 100*/
225M 356 311 149 225 435 19 60 140 18 53 125
M20 x 42 445 414 639 400 350 450 19 5.0 21.0
60*/ 53*/
250M 406 349 168 250 490 24 65
140 18 58
125 M20 x 42 500 440 690 400 350 450 19 5.0 21.0
IEC Quick Reference Dimensional Chart
IEC Frame Dimensions (Millimeters)
*2 Pole Dimensions 1mm = .03937”, 1” = 25.4mm
NOT
DEFINED
BY
IEC 72
B3 Foot-Mounted (Ridge Base)
FF Flange B5 Mount FT Face B14 Mount
FRAME
Mounting Shaft General B5 (FF) Flange B14 (FT) Face
A B C H AB K D E F G ED DH AC AD HD M N P S T LA M N P S T LA
63 100 80 40 63 119 7 11 23 4 8.5 10 M4 x 10 126 – 169 115 95 140 10 3.0 7 75 60 90 M5 2.5 7
71 112 90 45 71 131 7 14 30 5 11.0 20 M5 x 12.5 140 – 186 130 110 160 10 3.5 7 85 70 105 M6 2.5 9
80 125 100 50 80 157 10 19 40 6 15.5 25 M6 x 16 158 132 212 165 130 200 12 3.5 12 100 80 120 M6 3.0 9
90S 140 100 56 90 174 10 24 50 8 20.0 32 M8 x 19 178 140 230 165 130 200 12 3.5 12 115 95 140 M8 3.0 9
90L 140 125 56 90 174 10 24 50 8 20.0 32 M8 x 19 178 140 230 165 130 200 12 3.5 12 115 95 140 M8 3.0 9
100L 160 140 63 100 205 12 28 60 8 24.0 40 M10 x 22 215 178 278 215 180 250 15 4.0 11 130 110 160 M8 3.5 14
112M 190 140 70 112 245 12 28 60 8 24.0 40 M10 x 22 220 190 302 215 180 250 15 4.0 12 130 110 160 M8 3.5 11
132S 216 140 89 132 280 12 38 80 10 33.0 56 M12 x 28 275 210 342 265 230 300 15 4.0 12 165 130 200 M10 3.5 14
132M 216 178 89 132 280 12 38 80 10 33.0 56 M12 x 28 275 210 342 265 230 300 15 4.0 12 165 130 200 M10 3.5 14
160M 254 210 108 160 325 15 42 110 12 37.0 80 M16 x 36 325 254 414 300 250 350 19 5.0 13 215 180 250 M12 4.0 13
160L 254 254 108 160 325 15 42 110 12 37.0 80 M16 x 36 325 254 414 300 250 350 19 5.0 13 215 180 250 M12 4.0 13
180M 279 241 121 180 335 15 48 110 14 42.5 80 M16 x 36 360 310 490 300 250 350 19 5.0 15
180L 279 279 121 180 335 15 48 110 14 42.5 80 M16 x 36 360 310 490 300 250 350 19 5.0 15
200L 318 305 133 200 395 19 55 110 16 49.0 100 M20 x 42 400 340 540 350 300 400 19 5.0 19.5
55*/ 110*/ 16*/ 49*/ 100*/
225S 356 286 149 225 435 19 60 140 18 53 125
M20 x 42 445 414 639 400 350 450 19 5.0 21.0
55*/ 110*/ 16*/ 49*/ 100*/
225M 356 311 149 225 435 19 60 140 18 53 125
M20 x 42 445 414 639 400 350 450 19 5.0 21.0
60*/ 53*/
250M 406 349 168 250 490 24 65
140 18 58
125 M20 x 42 500 440 690 400 350 450 19 5.0 21.0
IEC Quick Reference Dimensional Chart
IEC Frame Dimensions (Millimeters)
*2 Pole Dimensions 1mm = .03937”, 1” = 25.4mm
NOT
DEFINED
BY
IEC 72
B3 Foot-Mounted (Ridge Base)
FF Flange B5 Mount FT Face B14 Mount
53
Additional Motor options for Product Selection table
MotoR/PoWER tYPE
AD
3PH AC Inverter Duty Motors (C-Face, Footless)
AA INV.DUTY, 0.25HP (.18KW), 230/460V
AB INV.DUTY, 0.33HP (.25KW), 230/460V
AC INV.DUTY, 0.5HP (.37KW), 230/460V
AD INV.DUTY, 0.75HP (.55KW), 230/460V
AE INV.DUTY, 1.0HP (.75KW), 230/460V
AF INV.DUTY,1.5HP (1.1KW), 230/460V
AG INV.DUTY, 2.0HP (1.5KW), 230/460V
AH INV.DUTY, 3.0HP (2.2KW), 230/460V
AJ INV.DUTY, 5.0HP, 230/460V
Brake Motors (3PH, C-Face, Removable Base)
BA BRAKE MOTOR, 0.5HP (.37KW), 230/460V
BB BRAKE MOTOR, 0.75HP (.55KW), 230/460V
BC BRAKE MOTOR, 1.0HP (.75KW), 230/460V
BD BRAKE MOTOR, 1.5HP (1.1KW), 230/460V
BE BRAKE MOTOR, 2.0HP (1.5KW), 230/460V
BF BRAKE MOTOR, 3.0HP (2.2KW), 230/460V
BG BRAKE MOTOR, 5.0HP, 230/460V, 3PH
Single Phase AC Motors (C-Face, Footless)
CA SINGLE PHASE, 0.25HP, 115/230VAC
CB SINGLE PHASE, 0.33HP, 115/230VAC
CC SINGLE PHASE, 0.5HP, 115/230VAC
CD SINGLE PHASE, 0.75HP, 115/230VAC
CE SINGLE PHASE, 1.0HP, 115/230VAC
CF SINGLE PHASE, 1.5HP, 115/230VAC
CONSULT FACTORY FOR OTHER OPTIONS
AD
PMDC Motors-Low Volt (C-Face, Removable Base)
DA PMDC, 0.25HP, 12V
DB PMDC, 0.33HP, 12V
DC PMDC, 0.33HP, 24V
DD PMDC, 0.5HP, 12V
DE PMDC, 0.5HP, 24V
DF PMDC, 0.75HP, 12V
DG PMDC, 0.75HP, 24V
DH PMDC, 1.0HP, 12V
DJ PMDC, 1.0HP, 24V
DK PMDC, 1.5HP, 24V
DL PMDC, 2.0HP, 24V
PMDC Motors-High Volt (C-Face, Removable Base)
EA PMDC, 0.25HP, 90V
EB PMDC, 0.25HP, 180V
EC PMDC, 0.33HP, 90V
ED PMDC, 0.33HP, 180V
EE PMDC, 0.5HP, 90V
EF PMDC, 0.5HP, 180V
EG PMDC, 0.75HP, 90V
EH PMDC, 0.75HP, 180V
EJ PMDC, 1.0HP, 90V
EK PMDC, 1.0HP, 180V
EL PMDC, 1.5HP, 180V
EM PMDC, 2.0HP, 180V
CONSULT FACTORY FOR OTHER OPTIONS
See pages 17 - 18 and 41 - 42
notES
ADPowerWash Xt Washdown (3PH, C-Face, Footless)SA White Epoxy (IP55) 0.25HP, 208-230/460V
SB White Epoxy (IP55) 0.33HP, 208-230/460V
SC White Epoxy (IP55) 0.5HP, 208-230/460V
SD White Epoxy (IP55) 0.75HP, 208-230/460V
SE White Epoxy (IP55) 1HP, 208-230/460V
SF White Epoxy (IP55) 1.5HP, 208-230/460V
SG White Epoxy (IP55) 2HP, 208-230/460V
SH White Epoxy (IP55) 3HP, 208-230/460V
SJ White Epoxy (IP55) 5HP, 208-230/460V
PowerWash SXt Washdown (3PH, C-Face, Footless)SK Stainless Steel (IP55) 0.33HP, 208-230/460V
SL Stainless Steel (IP55) 0.5HP, 208-230/460V
SM Stainless Steel (IP55) 0.75HP, 208-230/460V
SN Stainless Steel (IP55) 1HP, 208-230/460V
SP Stainless Steel (IP55) 1.5HP, 208-230/460V
SQ Stainless Steel (IP55) 2HP, 208-230/460V
PowerWash Extreme Washdown (3PH, C-Face, Footless)
ST Stainless Steel (BISSC, IP66) 0.5HP, 208-230/460V
SU Stainless Steel (BISSC, IP66) 0.75HP, 208-230/460V
SV Stainless Steel (BISSC, IP66) 1HP, 208-230/460V
SW Stainless Steel (BISSC, IP66) 1.5HP, 208-230/460V
SX Stainless Steel (BISSC, IP66) 2HP, 208-230/460V
CONSULT FACTORY FOR OTHER OPTIONS
54
©2013 BISON Gear & Engineering Corp., All Rights Reserved 0019010913
Available on www.bisongear.com.
Many products are available to ship same day in 2 easy steps!
Step 1: Place an order via distribution rep, phone, fax or online at bisongear.com
Step 2: Choose UPS shipping method with your UPS account number (ship ground or red)
Note: Orders ship same day if received before 12:00 pm CST. Max order quantity of 5 pcs per part number.
SNS signifies model number availability. Lead time required with minimum order quantity.
RoBuStICItY® There’s a simple philosophy behind the design of every Bison product: start with the highest quality components and then, through better design and manufacturing techniques, maximize the throughput those components can produce. Higher quality components means more dependable performance, fewer field failures, up to 200% more torque than typical - leading to a lower cost per inch-pound of torque, a more compact product and longer service life.
EnGInEERInG EXCELLEnCE We take pride that we are Bison Gear & Engineering. With more than 35% of our staff being an accredited engineer, we are committed to maintaining the engineering excellence needed to meet and exceed our customers’ expectations. So whether you need a standard unit or custom design, Bison has the engineering capability to provide optimized designs for your application needs.
CuStoMER SERVICE Our dedicated staff of inside sales specialists and outside technical sales team means that Bison is always available to assist our customers with quick response to their immediate needs.
FLEXIBLE MAnuFACtuRInGWhether the need is a lot or just a few at a time, Bison’s lean optimized manufacturing floor is able to rapidly respond to the needs of our customers. Our factory is equipped with state-of-the-art manufacturing equipment, allowing us to get the products out the door and into the hands of the customer faster.
CoRPoRAtE RESPonSIBILItYAt Bison, we uphold our responsibility to our associates and our community. With our continued education programs (G.E.A.R.) and our MSSC training center, we provide our associates with a pathway for advancement and a long-lasting career in manufacturing. Through BisonCares, our 501c3 organization, we contribute to a number of local and national charities and manage several programs to give back to the community.
3850 Ohio Avenue, St. Charles, IL 60174 | www.bisongear.com | [email protected] 1.800.ATBISON (282-4766) | Int’l Phone: +1.630.377.4327
tHE BISon VALuE