Instruction Sheet smarTROLL Calibration Kit Instruction Sheet Learn ...
Transcript of Instruction Sheet smarTROLL Calibration Kit Instruction Sheet Learn ...
Technical Note
Innovations in Water Monitoring
Instruction Sheet
Innovations in Water Monitoring
Page 1 Page 1
Kit Contents (0080830)
• Battery-poweredairpump• Largebubblercup,tubing,checkvalve,andpinch
valveforcalibratingthe100%dissolvedoxygensaturationpoint.
• Restrictortoaccommodatethesub2-inchTROLL9500instrument
• 2alkalineD-cellbatteries• Sodiumsulfitesolution,500mLforcalibratingthe
0%dissolvedoxygenpoint• Inadditiontotheseitems,youwillneedtheplastic
calibrationcupthatcamewiththeinstrumentforcalibratingthe0%dissolvedoxygenpoint.
Kit Contents (0048580)
• Battery-poweredairpump• Largebubblercup,tubing,checkvalve,andpinch
valveforcalibratingthe100%dissolvedoxygensaturationpoint.
• 2alkalineD-cellbatteries• Sodiumsulfitesolution,500mLforcalibratingthe
0%dissolvedoxygenpoint• Smallcalibrationcupforcalibratingthe0%
dissolvedoxygenpoint.
Calibration Kit for the Aqua TROLL® 400, SMARTROLL™ MP and TROLL® 9500 RDO ® Sensor
0080830 – for Aqua TROLL 400 Instrument and TROLL 9500 Instrument (sub 2-inch), SMARTROLL™ MP0048580 – for TROLL 9500 Instrument (sub 4-inch)
Page 2
Informationsubjecttochangewithoutnotice.In-Situ,In-Situlogo,BaroMerge,BaroTROLL,HERMIT,iSitu,RDO,Pocket-Situ,RuggedCable,RuggedReader,TROLL,andWin-SituaretrademarksorregisteredtrademarksofIn-SituInc.©2012.Allrightsreserved.
For more information, contact In-Situ Inc. 221 East Lincoln Avenue, Fort Collins, CO 80524 1-800-446-7488 (toll-free in U.S.A. & Canada)1-970-498-1500 (international & domestic)www.in-situ.com 0080832 Rev. 004 04/13
Application
TheRDO®Sensorisextremelystable,whicheliminatestheneedforfrequentcalibration.Standardoperatingprocedures,environmentalconditions(e.g.,potentialforfouling,abrasiveconditions)maynecessitateroutinecalibration.
AfterinstallinganewRDOSensor,In-Situ®recommendsthatyouperformacalibration.Forbestresults,performa2-pointcalibrationat100%and0%dissolvedoxygen(DO)saturationbeforeusingthesensor.
100% Oxygen Saturation Calibration
1. Installthebatteriesintheportableairpumpasshowninthediagramontheinsidecover.
2. Fillthelargecalibrationcuptowithin4cm(1.5in.)ofthetopwithcleanwater.
Note: Use tap water, distilled water, or your sample matrix if it is freshwater, not brackish or saline.
3. Turnonthebubbler,openthepinchvalveonthetubing.Runatfullflowratefor10minutestofullysaturatethewaterwithoxygen.After10minutesyoucanusethecontrolvalvetomatchthewaterturbulenceconditionsexpectedinthefield.
4. PlacetheinstrumentinthewaterensuringthatthesensorandthetemperaturethermistorarecompletelysubmergedandthattheRDOsensingmaterialisnotinthedirectpathofthebubbles.
5. Connecttheinstrumenttoacomputerandestablishaconnectiontothecalibrationsoftware.
6. Followthecalibrationwizardprovidedinthesoftware.
Note: Video tutorials and operator’s manuals are available on the In-Situ website www.in-situ.com in the Tech Resources section.
0% Oxygen Saturation Calibration
1. Fillthesmallercalibrationcuptotheupperfilllinewithsodiumsulfite(NA2SO3)solution.
2. Placetheinstrumentinthesolutionandallowtimefortemperaturestabilization.
3. EnsuretherearenoairbubblesonthesensingsurfaceoftheRDOSensor.
4. Followthecalibrationwizardprovidedinthesoftware.
Note: Video tutorials and operator’s manuals are available on the In-Situ website www.in-situ.com in the Tech Resources section.
5. Whenyouarefinishedrinsethoroughlyincleanwater.
Replacement Parts
Sodium sulfite solution, 500 mL 0017670