INSTRUCTION MANUAL PROLUXE - Oakworks Med

I N S T R U C T I O N M A N U A L

www.oakworks.com · 717.235.6807

your portable table converted to a lift table and back again

converts in seconds! ...then back to a portable!PROLUXE™convertible

© Copyright 2011 Oakworks® , Inc.

Manual Part # MMMNST00221st Edition, January 2011Printed in U.S.A.

All rights are reserved. No part of this document may be photocopied, reproduced or translated to another language without prior written consent of Oakworks®, Inc.

Oakworks® is a registered trademark of Oakworks®, Inc.

Notice

The information contained in this document is subject to change without notice and should not be construed as a commitment by Oakworks®, Inc.

Oakworks®, Inc. assumes no responsibility for any errors that may appear in this document nor does it make expressed or implied warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.

Oakworks®, Inc. shall not be liable for incidental or consequential damages in connection with or arising out of the furnishing, performance, or use of this document and the program material which it describes.

TABLE OF CONTENTS

TABLE OF CONTENTS

TAB

LE O

F C

ON

TEN

TS

Symbol Identification .................................................................................. pg 1

Warnings & Cautions .............................................................................pg 1

Grounding Instructions ..........................................................................pg 2

Product Description & Specs ................................................................pg 3

Directions for Use

One time only set up ...........................................................pg 4 - 8

Loading your portable table .............................................. pg 9 - 11

Remove your portable table ................................................... pg. 12

Controls - Foot control & Hand control ................................... pg 13

Using your ProLuxe Convertible ................................................ pg 14

General care of equipment ....................................................................... pg 15

Electrical specifications .............................................................................. pg 15

Power & lead plug ID .................................................................................. pg 16

Contact Information ..................................................................... back cover

1

WARNINGS & CAUTIONS

SYM

BO

L ID

& W

AR

NIN

GS

SYMBOL IDENTIFICATION - WARNINGS & CAUTIONS

SYMBOL IDENTIFICATION

This symbol, when used in this manual and on product labels, represents a caution warning. Be sure to read and comply with all precautions and warnings.

This symbol, when used in this manual and on product labels, warns against an electrical shock hazard. Be sure to observe and comply with all warnings.

This symbol, when used in this manual or on product labels, indicates a Protective Earth (Ground) Terminal.

This symbol when used in this manual or on product labels, warns that during transport there should be no stacking of containers.

This symbol, when used in this manual or on product labels, indicates that the product should be protected from moisture. The humidity specifications for Transport & Storage are listed in the back of this manual.

This symbol, when used in this manual or on product labels, indicates that information is given regarding the recommended temperature limits during transport and storing.

This symbol, when used in this manual or on product labels, indicates the date of manufacture of the device.

This symbol, when used in this manual or on product labels, indicates alternating current (AC).

This symbol, when used in this manual or on product labels, indicates direct current (DC).

This symbol, when used in this manual or on product labels, indicates that instructional information is included. It should be read carefully and completely .

~----

Improper use of this device can cause injury. Be sure to read all operating instructions prior to use.

Weight limit is defined by the portable table used with this product. (If the portable table has a weight limit of 450 lbs, then the system is 450 lbs) up to a maximum of 550 lbs.

Be certain that the table is completely lowered prior to discharging an ambulatory patient. The patient may lose balance and fall.

Electrical Shock Hazard. The power supply/control module is located below the base of the table. No user serviceable parts are inside. Refer servicing to qualified personnel. Before doing any work on the unit or cleaning with any liquid cleaner, unplug wall con-nector prior to contact with any cables connected to the power supply.

Plug table into an outlet that is surge protected to a level of 750J or higher. Failure to do this may void all or part of the warranty.

WARNINGCAUTION

WARNING

CAUTION

2

GROUNDING

GR

OU

ND

INGGROUNDING

INSTRUCTIONS

This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electrical current to reduce the risk of electric shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. See U.S. sample below.

This product is manufactured for use on a nominal 120-volt circuit for the United States and a nominal 220-volt circuit for use in Europe. The plug has a grounding pin in a pattern that varies by country as shown in the Product Identification section of this manual. Make sure that the product is connected to an outlet having the same configuration as the plug.

DANGER-Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service man if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product - if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

To reduce the risk of electric shock, this furnishing has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

No adapter should be used with this product.

CAUTION

GROUNDING INSTRUCTIONS

3

DIR

EC

TIO

NS

FOR

USE

DIRECTIONS FOR USE

PRODUCT DESCRIPTION

wheels (2)

TABLE SPECIFICATIONS

• Height Range: 20” - 36”

• Width: fits portable tables 27” - 33” wide

• Lift Capacity: Weight limit is defined by the portable table used with this product. (If the portable table has a weight limit of 450 lbs, then the system is 450 lbs) up to a maximum of 550 lbs.

• Top: works with rectangular, round corner, or backrest portable tables

• Electronics: 120v or 220v electric motor

(1) low voltage hand control or (1) low voltage foot control

knobs (4)

Adjustable portable table supports (2 sets)

Center alignment groove

Portable table secure strap

Strap cleat

electric motor

End bumper of portable table support

Hook behind the cleat

4

PR

EP

AR

E Y

OU

R P

RO

LUX

E C

ON

VE

RTI

BLE

PREPARE YOUR PROLUXE CONVERTIBLE

ONE TIME ONLY PROLUXE CONVERTIBLE SET-UP

STEP 1Loosen all knobs below the adjustable portable table supports by turning the knob counter-clockwise.

STEP 2Slide the adjustable portable table supports to their widest position.

STEP 3Remove the portable table secure strap from the strap cleat (if necessary).

STEP 4Plug in the Convertible and lower to its lowest height

This is a one time only procedure for each given portable table.

5

PR

EP

AR

E Y

OU

R P

RO

LUX

E C

ON

VE

RTI

BLE


STEP 5Open your portable table on its side.

STEP 6Remove the shiatsu cables or bolts on one side to enable your table to lay flat. There are different types of shiatsu cables. Follow the directions below based on the type you have. Or follow your table manufacturer’s instructions.

WING NUT

Remove the wing nut

Location of Shiatsu release bolts or wing nuts

Remove wood brace Remove cable Replace wood brace and wing nut

Repeat these steps on both sides of the table. Locations shown above.

C-CLAMP

C-Clamp closed Open C-Clamp Remove Shiatsu cable

Repeat these steps on both C-Clamps.

Close C-Clamp

CAUTIONFollow your table manufacturer’s instructions for using the Shiatsu option if your table has them.

The instructions shown here are for general reference only.

NOTE: Some systems may be slightly different such as; cable not between braces, hex nut instead of wing nut. You may need to use a wrench to remove the bolt.

6


STEP 6With your ProLuxe Convertible at its lowest height, stand at the side where the portable table supports are towards the outside, as shown here.

Have the widest side of the adjustable portable table supports facing you.

ALift your portable table onto the ProLuxe Convertible base.

BOpen your portable table so that it is flat and position the bottom away from you.

CLower your portable table onto the ProLuxe Convertible base.

CAUTIONBe sure to read and follow the directions on how to center & secure your portable table (shown on page 7) before use.

PR

EP

AR

E Y

OU

R P

RO

LUX

E C

ON

VE

RTI

BLE

STEP 7Load your portable table

7


STEP 8Once your portable table is on the ProLuxe Convertible, you are ready to align & secure it to the base.

BVisually center the portable table with the base of the ProLuxe Convertible on both ends.

CBe sure that the knobs are loose so you can adjust the table supports.

DKeeping the portable table centered, push the adjustable table supports together against the sides of your portable table.

AAlign the hinge of the portable table over the center alignment groove.

Hinge of portable table


PR

EP

AR

E Y

OU

R P

RO

LUX

E C

ON

VE

RTI

BLE

8

EOnce the table supports are snug against the sides of the portable table, tighten the knobs to secure into place.

FDouble check that the hinge of the portable table is still aligned over the center alignment groove.


PR

EP

AR

E Y

OU

R P

RO

LUX

E C

ON

VE

RTI

BLE

NOTE: On tables with a backrest, leave a little space between the end bumpers and the backrest before tightening to allow movement of the backrest.

GInsert strap into the center of the table. Attach one end of the strap as shown. Hold strap with one hand and with the other hand, slide strap thru the cleat. Then, loop strap gently through the hook behind the cleat.

HPull the strap thru the center of the table and down into the space between the two top parts. Snugly attach the other end of the strap as shown. (Pull down, insert in cleat, pull firmly through cleat, gently loop cord over small hook behind the cleat.)

CAUTIONThe table must be secured properly to the base to insure it is safe. Make sure the strap is through the hook behind the cleat.

ITry to lift the portable table to check for slack. There should not be much, if any. If it is too loose, retighten portable table secure strap.

9

DIRECTIONS FOR USE

DIR

EC

TIO

NS

FOR

USE

STEP 1Open your portable table on its side.

STEP 2Remove the shiatsu cables or bolts to enable your table to lay flat. There are different types of shiatsu cables. Follow the directions below based on the type you have. Or follow your table manufacturer’s instructions.

WING NUT

Remove the wing nut

Location of Shiatsu release bolts or wing nuts

Remove wood brace Remove cable Replace wood brace and wing nut

Repeat these steps on both sides of the table. Locations shown above.

C-CLAMP

C-Clamp closed Open C-Clamp Remove Shiatsu cable

Repeat these steps on both C-Clamps.

Close C-Clamp

CAUTION

LOADING YOUR PORTABLE TABLE

This is done every time you remove and replace your portable table. All the adjustments to the base do not need to be done again.

Follow your table manufacturer’s instructions for using the Shiatsu option if your table has them.

The instructions shown here are for general reference only.

STEP 3With your ProLuxe Convertible at its lowest height, stand at the side where the portable table supports are towards the outside, as shown here.

Have the widest side of the adjustable portable table supports facing you.

STEP 4Lift your portable table onto the ProLuxe Convertible base.

STEP 5Open your portable table so that it is flat and position the bottom away from you.

STEP 6Lower your portable table onto the ProLuxe Convertible base.

Follow these steps to place your portable table on top of the ProLuxe Convert-ible. Make sure you have already completed the “one-time” set up section called “Prepare your ProLuxe Convertible” (page 4-8)

CAUTIONBe sure to read and follow the directions on how to center & secure your portable table (shown on page 7) before use.

10

DIRECTIONS FOR USE

DIR

EC

TIO

NS

FOR

USE

11

DIRECTIONS FOR USE

DIR

EC

TIO

NS

FOR

USE

STEP 8Align the hinge of the portable table over the center alignment groove.

Hinge of portable table


STEP 7Make sure your portable table fits down and inside the end bumpers of the portable table supports.

STEP 9Insert strap into the center of the table. Attach one end of the strap as shown. Hold strap with one hand and with the other hand, slide strap thru the cleat. Then, loop strap gently through the hook behind the cleat.

STEP 10Pull the strap thru the center of the table and down into the space between the two top parts. Snugly attach the other end of the strap as shown. (Pull down, insert in cleat, pull firmly through cleat, gently loop cord over small hook behind the cleat.)

CAUTIONThe table must be secured properly to the base to insure it is safe. Make sure the strap is through the hook behind the cleat.

STEP 11Try to lift the portable table to check for slack. There should not be much, if any. If it is too loose, retighten portable table secure strap.

12

REMOVE YOUR PORTABLE TABLE

RE

MO

VE

YO

UR

PO

RTA

BLE

TA

BLEREMOVING YOUR PORTABLE TABLE

STEP 1Remove the portable table secure strap.

STEP 3Reattach your portable table’s cabling system to restore your table to a safe operating configuration. Fold your portable table & you’re ready to go!

STEP 2Lift your portable table off the ProLuxe Convertible base.

CAUTIONBe sure to secure your portable table’s Shiatsu cables according to manufacturer’s instructions before use.

13

DIR

EC

TIO

NS

FOR

USE

DIRECTIONS FOR USE

CAUTIONWhen operating the controls be sure to observe all cautions and warnings given in the manual to prevent injury to both operator and client.

CAUTION

CAUTION

When operating the controls and making any and all adjustments to the table, move hands and feet away from the working mechanism of the table.

Children must be supervised when around this equipment by a responsible adult.

Foot Control:

UPDOWN

HAND CONTROL OPERATIONSDIRECTIONS FOR USE - CONTROLS

The ProLuxe Convertible comes with choice of either hand or foot control for easy height adjustments.

Hand Control:

DOWNUP

14

DIRECTIONS FOR USE

DIR

EC

TIO

NS

FOR

USEUSING YOUR PROLUXE CONVERTIBLE - ACCESSORIES

All of your portable table accessories will work with the ProLuxe Convertible. Install according to manufacturer’s instructions.

FACE RESTShown here with QuickLock™ Face Rest & Boiance™ crescent.

ARM HAMMOCKShown here with QuickLock™ Face Rest, Aero·Cel crescent & Arm Hammock.

USING YOUR PROLUXE CONVERTIBLE - APPLICATION

Adjust the height of your table to achieve optimal working height for multiple therapists, clients or treatments without straining your body.

The powerful motor lifts up to 550 lbs. over a 16” height range, and the super stable design insures your clients feel safe.

100 VAC/20amps

1.5 amps

11.0 amps

24 VDC

330 watts

Class 1 Equipment

Type B Applied Part

IPX0

Continuous Operation @ 10% Duty Cycle

15

MA

INTE

NA

NC

E

MAINTENANCE

ELECTRICAL SPECIFICATIONS

Designed For: North America Europe Japan/Korea

Input Service

Current Draw

Maximum Monentary Current Draw

Voltage Output (control box)

Power Consumption

Electric Shock Protection

Tabletop Applied Part

Table Top IEC 529 Rating

Mode of Operation

120 VAC/20amps

2.7 amps

9.0 amps

24 VDC

330 watts

Class 1 Equipment

Type B Applied Part

IPX0


Storage & Transport

Temperature: 32º - 100º F 0º-38º C Humidity: 60% relative humidity Pressure: no limitations knownDuring transport, DO NOT stack containers.

230 VAC/10amps

1.5 amps

5.0 amps

24 VDC

330 watts

Class 1 Equipment

Type B Applied Part

IPX0


GENERAL CARE OF EQUIPMENT COMPONENTS

• Use only a mild solution of 4:1 diluted non-alcohol cleaner such as 409®, Fantastik® or some other non-abrasive cleaner to wipe down the metal surfaces. Apply with a damp (not wet) lint-free cloth. Be sure excess liquid does not drip onto, or into, any of the electrical controls or mechanisms. Be sure that the unit is unplugged before cleaning these areas. Wipe these areas carefully with a lint free cloth.

• Electronic and or manual lift mechanisms require no general maintenance or lubrication.

• If the table will be out of use for an extended period of time, the power cord should be unplugged from the receptacle. To prevent inadvertent damage to the plug or cord, the cable should be coiled and secured with a wire tie or rubber band.

• It is important to visually inspect your tabe on a quarterly basis to ensure all components are working properly and safely. Be sure to tighten all bolts to be sure they are secure. Over time they may work their way loose, leading to an unsafe condition.

16

PRODUCT IDENTIFICATION - POWER LEAD PLUGS

Oakworks® Part #: Voltage (AC) Power Cord Plug

5097-11 120v 60 Hz 3 prong grounded hospital grade; North America

5097-3 220v 50 Hz Continental Plug; Europe

5097-4 220v 50 Hz Swiss plug; Switzerland

5097-2 220v 50 Hz British plug; United Kingdom

N/A 100v 50/60 Hz 2 prong polarized plug; (Plug comes Japan & Korea w/Control Box; order Control Box pn #4046-3)

PO

WE

R P

LUG

S

POWER PLUGS

Manual Part Number MMMNST0022Revision date: 05.10.11Edition 1, EnglishPrinted in USA

I N S T R U C T I O N M A N U A L

CONTACT INFORMATION:

Oakworks® Inc.

923 East Wellspring Road New Freedom, PA 17349

Toll Free (USA only): 800-916-4613 Phone: 717-235-6807

FAX: 717-235-6798

www.oakworks.com

PROLUXE™convertible

INSTRUCTION MANUAL PROLUXE - Oakworks Med

Documents

Transcript of INSTRUCTION MANUAL PROLUXE - Oakworks Med