Installing Deadbolt a. b. Tools Needed: Deadbolt A B...
2
If you have a new door that is not pre-bored, follow these instructions. If your door is pre-bored, proceed to Single Cylinder or Double Cylinder Installation. The template provided must be taped to the door as shown to mark locations for drilling holes. To position the template, fold the template on line and locate on door at specified height (about 40” from the floor). If the door is beveled , place the folded edge on the low side of the bevel as shown in the illustration. Determine the door thickness and backset (2-3/8” or 2-3/4”). Mark the door for face and edge bores. Tools Needed: Door Preparation Tools Needed: Deadbolt Installation Exploded View Single Cylinder Deadbolt Exploded View Double Cylinder Deadbolt Parts Enclosed: If your door is not pre-bored, see Door Preparation section. 1. Pencil 2. Measuring Tape or Rule 3. 2-1/8” Diameter Hole Saw 4. 1/2” or 3/4” Wood Chisel 5. Drill and assorted bits 1/8”, 5/32” and 1” 1. 2 each #8 - 32 Oval Head Machine Screw 2. 1 Turnpiece Trim 3. 2 each #10 -32 x 1-7/8” Pan Head Machine Screw 4. 1 Turnpiece Mounting Plate 5. 1 Adjustable Backset Deadbolt 6. 4 each #8 x 3/4” Flathead Combination Screws 7. 1 Outside Cylinder Collar 8. 1 Outside Cylinder 9. Screw Guide Parts Enclosed: 1. 1 Inside Cylinder Collar 2. 1 Cylinder Cover 3. 2 each #10 -32x2-1/4” Flat Head Machine Screws 4. 1 Inside Cylinder 5. 1 Threaded Collar Note: See Strike Installation section for strike parts listing. Note: See Strike Installation section for strike parts listing. 6. 1 Adjustable Backset Deadbolt 7. 4 each #8 x 3/4” Flathead Combination Screws 8. 1 Outside Cylinder Collar 9. 1 Outside Cylinder 10. Screw Guide 1. Measuring Tape or Rule 2. One pair needle-nose pliers 3. One pair slip joint or lineman’s pliers 4. No. 2 and No. 3 Phillips Head Screwdrivers 5. 1/8” Allen Wrench (supplied) 6. Flat Head Screwdriver Chisel out the area marked for the faceplate to a depth of 5/32” or until the faceplate is flush with the door edge. Proceed to the “Installing the Deadbolt” section. Insert deadbolt into edge of door. While holding faceplate, trace the outline of the faceplate onto the door edge. Mark screw hole centers and drill pilot holes with a 1/8”drill. Drill the 2-1/8” diameter face bore (A) through the door. Drill 1” diameter edge bore (B) 3-1/2” deep for 2-3/8” backset, or 3-7/8” deep for 2-3/4” backset. To ensure the correct depth of hole B mark your drill bit using masking tape as shown in the illustra- tion. Caution: Re-check hole locations before drilling. A- 2-1/8” DIAMETER B- 1” DIAMETER Face bore Edge bore A B Door Preparation b. Place the Turnpiece Mounting Plate over the bore on the inside of the door. When positioned properly the word “Top” will be at the 12 o’clock position and against the door ( not visible). Insert two #10- 32 x 1-7/8” pan head machine screws through the two holes in the Mounting Plate, through the deadbolt, and into the threaded holes on the back side of the Cylinder. Check that the Mounting Plate is centered on the bore in the door and rests flat against the door. Tighten the screws. Installing Deadbolt Double Cylinder Assembly a. Extend the deadbolt using a flat head screwdriver as shown. From the outside of the door, place the Screw Guide in the bored hole so that it fits around the Deadbolt. Note: The screw guide must be mounted from the exterior side of the door. The arrow on the screw guide must be visible and pointing up. Place the Collar over the hole, and insert the Cylinder into the Collar and Deadbolt. Note: Cylinder tailpiece must be vertical when installing cylinder. Hold in place while moving to step b. Do not insert key into the Cylinder during this procedure. b. Insert deadbolt. Secure with two #8 x 3/4" flat head combination screws provided (see diagram for proper positioning). Ensure deadbolt head is extended throughout installation procedure. a. Carefully break off cylinder tailpiece at required mark for your door thickness. Caution; use two pairs of pliers as shown or tailpiece will be damaged. b. Align tailpiece with slot. Keep tailpiece vertical and curved toward right side of the hole as illustrated. c. Place the Turnpiece Trim over the Mounting Plate. The turnpiece must be horizontal as shown in the illustration. The cylinder tailpiece, in the vertical position, must slide into the turn- piece slot. Attach the Turnpiece Trim to the Mounting Plate with two #8-32 x 5/8” oval head machine screws. Tighten the screws. a. Extend the deadbolt using a flat head screwdriver as shown. From the outside of the door, place the Screw Guide in the bored hole so that it fits around the Deadbolt. Note: The screw guide must be mounted from the exterior side of the door. The arrow on the screw guide must be visible and pointing up. Place the Collar over the hole, and insert the Cylinder into the Collar and Deadbolt. Note: Cylinder tailpiece must be vertical when installing cylinder. Hold in place while moving to step b. Do not insert key into the Cylinder during this procedure. b. Insert the Inside Cylinder into the hole in the Threaded Collar. The slot in the top of the Inside Cylinder engages the notch in the Threaded Collar. Place these two components into the bore on the inside of the door so that the tail- piece from the Inside Cylinder engages the slot in the Deadbolt. Insert two #10-32 x 2-1/4” flat head machine screws into the two holes on the Inside Cylinder and tighten them down to connect the components on the outside of the door. Note: the tailpiece on the cylinder must be vertical and towards the right side of the hole during this procedure. Do not insert the key into either cylinder during this step. Tailpiece OUTSIDE INSIDE Install deadbolt with both long slots on latch body in upper position. Cylinder Slot Single Cylinder Assembly OUTSIDE Rotate to adjust backset. INSIDE a. The deadbolt supplied with this unit has an adjustable back- set feature. When removed from the box it will be set at 2-3/8” backset. To adjust the deadbolt to 2-3/4” backset, grasp the body and twist thefaceplate / bolthead assembly 180 degrees until it stops. The unit is now ready for installation in 2-3/4” backset. TEAR HERE FOR ENGLISH. TEAR HERE FOR ENGLISH. INSIDE TOP VIEW OUTSIDE CYLINDER CYLINDER TAILPIECES MUST MEET EACH OTHER AS SHOWN c. Align the cylinder cover over the inside cylinder. Screw on the inside cylinder collar. INSIDE Tailpiece Break with this plier Cylinder Hold with this plier INSIDE Top view of door Template A B Low side of bevel Door Thickness backset
Transcript of Installing Deadbolt a. b. Tools Needed: Deadbolt A B...
If you have a new door that is notpre-bored, follow these instructions.If your door is pre-bored, proceed toSingle Cylinder or Double CylinderInstallation. The template providedmust be taped to the door as shownto mark locations for drilling holes.To position the template, fold thetemplate on line and locate on doorat specified height (about 40” fromthe floor). If the door is beveled,place the folded edge on the lowside of the bevel as shown in theillustration. Determine the doorthickness and backset (2-3/8” or 2-3/4”). Mark the door for face and edge bores.
Tools Needed: Door Preparation
Tools Needed: Deadbolt Installation
Exploded View Single Cylinder Deadbolt
Exploded View Double Cylinder Deadbolt
Parts Enclosed:
If your door is not pre-bored, see Door Preparation section.1. Pencil2. Measuring Tape or Rule3. 2-1/8” Diameter Hole Saw4. 1/2” or 3/4” Wood Chisel5. Drill and assorted bits 1/8”,
5/32” and 1”
1. 2 each #8 - 32 Oval Head Machine Screw 2. 1 Turnpiece Trim3. 2 each #10 -32 x 1-7/8” Pan Head Machine Screw4. 1 Turnpiece Mounting Plate5. 1 Adjustable Backset Deadbolt6. 4 each #8 x 3/4” Flathead Combination Screws7. 1 Outside Cylinder Collar8. 1 Outside Cylinder9. Screw Guide
Parts Enclosed:1. 1 Inside Cylinder Collar2. 1 Cylinder Cover3. 2 each #10 -32x2-1/4” Flat Head
Machine Screws4. 1 Inside Cylinder5. 1 Threaded Collar
Note: See Strike Installation section for strike parts listing.
Note: See Strike Installation section for strike parts listing.
6. 1 Adjustable Backset Deadbolt7. 4 each #8 x 3/4” Flathead
Combination Screws8. 1 Outside Cylinder Collar9. 1 Outside Cylinder10. Screw Guide
1. Measuring Tape or Rule2. One pair needle-nose pliers3. One pair slip joint or lineman’s
pliers4. No. 2 and No. 3 Phillips Head
Screwdrivers5. 1/8” Allen Wrench (supplied)6. Flat Head Screwdriver
Chisel out the area marked for thefaceplate to a depth of 5/32” oruntil the faceplate is flush withthe door edge. Proceed to the“Installing the Deadbolt” section.
Insert deadbolt into edge of door.While holding faceplate, trace theoutline of the faceplate onto thedoor edge. Mark screw holecenters and drill pilot holes with a1/8”drill.
Drill the 2-1/8” diameter face bore (A) through the door.Drill 1” diameter edgebore (B) 3-1/2” deepfor 2-3/8” backset, or3-7/8” deep for 2-3/4”backset. To ensure thecorrect depth of hole Bmark your drill bitusing masking tape asshown in the illustra-tion.
Caution: Re-checkhole locationsbefore drilling.
A- 2-1/8” DIAMETERB- 1” DIAMETER Face bore
Edge bore
A
B
Door Preparation
b. Place the Turnpiece MountingPlate over the bore on the inside ofthe door. When positioned properlythe word “Top” will be at the 12o’clock position and against thedoor ( not visible). Insert two #10-32 x 1-7/8” pan head machinescrews through the two holes inthe Mounting Plate, through thedeadbolt, and into the threadedholes on the back side of theCylinder. Check that the MountingPlate is centered on the bore in thedoor and rests flat against thedoor. Tighten the screws.
Installing Deadbolt
Double Cylinder Assembly
a. Extend the deadbolt using a flat headscrewdriver as shown. From the outsideof the door, place the Screw Guide in thebored hole so that it fits around theDeadbolt. Note: The screw guidemust be mounted from the exteriorside of the door. The arrow on thescrew guide must be visible andpointing up. Place the Collar over thehole, and insert the Cylinder into theCollar and Deadbolt. Note: Cylinder tailpiece must be vertical when installingcylinder. Hold in place while moving tostep b. Do not insert key into theCylinder during this procedure.
b. Insert deadbolt. Secure with two #8 x 3/4" flathead combination screws provided (see diagramfor proper positioning). Ensure deadbolt head isextended throughout installation procedure.
a. Carefully break off cylindertailpiece at required mark for yourdoor thickness.Caution; use twopairs of pliers as shown or tailpiece will be damaged.
b. Align tailpiece with slot.Keep tailpiece vertical andcurved toward right side ofthe hole as illustrated.
c. Place the TurnpieceTrim over the MountingPlate. The turnpiecemust be horizontal asshown in the illustration.The cylinder tailpiece, inthe vertical position,must slide into the turn-piece slot. Attach theTurnpiece Trim to theMounting Plate with two#8-32 x 5/8” oval headmachine screws. Tightenthe screws.
a. Extend the deadbolt using a flathead screwdriver as shown. Fromthe outside of the door, place theScrew Guide in the bored hole sothat it fits around the Deadbolt.Note: The screw guide mustbe mounted from the exteriorside of the door. The arrow onthe screw guide must be visible and pointing up. Placethe Collar over the hole, andinsert the Cylinder into the Collarand Deadbolt. Note: Cylinder tailpiece must be vertical wheninstalling cylinder. Hold in placewhile moving to step b. Do notinsert key into the Cylinderduring this procedure.
b. Insert the Inside Cylinder into thehole in the Threaded Collar. The slot inthe top of the Inside Cylinder engagesthe notch in the Threaded Collar. Placethese two components into the bore onthe inside of the door so that the tail-piece from the Inside Cylinder engagesthe slot in the Deadbolt. Insert two #10-32 x 2-1/4” flat head machinescrews into the two holes on the InsideCylinder and tighten them down to connect the components on the outsideof the door. Note: the tailpiece on thecylinder must be vertical and towardsthe right side of the hole during this procedure. Do not insert the key intoeither cylinder during this step.Tailpiece
OUTSIDE
INSIDE
Install deadbolt withboth long slots on latchbody in upper position.
Cylinder
Slot
Single Cylinder Assembly
OUTSIDE
Rotate toadjust backset.
INSIDE
a. The deadbolt supplied withthis unit has an adjustable back-set feature. When removed fromthe box it will be set at 2-3/8”backset. To adjust the deadbolt to2-3/4” backset, grasp the bodyand twist thefaceplate / boltheadassembly 180 degrees until itstops. The unit is now ready forinstallation in 2-3/4” backset.
TEAR HERE FOR ENGLISH.TEAR HERE FOR ENGLISH.
INSIDE
TOP VIEW
OUTSIDECYLINDER
CYLINDERTAILPIECES
MUST MEET EACHOTHER AS
SHOWN
c. Align the cylinder cover overthe inside cylinder. Screw on theinside cylinder collar.
INSIDE
Tailpiece
Break withthis plier
Cylinder
Hold withthis plier
INSIDE
Top view of door
Template
AB
Low side of bevel
DoorThickness
backset
2-1/8” Deadbolt Preparation
TEAR HERE FOR ENGLISH.
PK-1229E (08/10)
Tahoe 2-1/8” CollarAuxiliary DeadboltInstallation Instructions
Logotype: Builders Hardware Manufacturers
consider using it on your company stationery, brochures, and print advertising.
Congratulations!
Remember Baldwin
With your purchase of The Images Collection solid brass deadbolt, you’re among a groupof discerning individuals who know the intrinsic value of selecting the finest – Baldwin.
Images entrance locksets, interior latchsets, and deadbolts coordinate beautifully, enabling youto carry a specific design theme throughout your home.
Our step-by-step installation instructions will help guide you through yourproject quickly and easily.
Before you begin your installation, read and understand theinstallation instructions and marking templates. If you have anyquestions, please do not hesitate to contact our Baldwin Technical Services Department,1-800-566-1986. We’re here to help!
NOTE: Failure to use all recommended components will void Grade 1 rating.
We thank you for your Baldwin purchase and wish you the fullestenjoyment of your Baldwin Handleset.
With the completion of your project, remember that Baldwin qualityhardware products are available for all your decorating and remodel-ing needs. Matching knob and leversets for interior doors, beautifulbath accessories, and a complete selection of cabinet and doorenhancing hardware are all available from your Baldwin retailer.
©2010 Baldwin Hardware CorporationLake Forest, California, 92610
Technical Services Support1-800-566-1986
Hours: 8 a.m. to 8 p.m. E.S.T - Monday - Friday 10 a.m. to 6 p.m. E.S.T - Saturday
Strike Installation
Complete deadboltinstallation beforeinstalling the strike.Install weather stripping before setting the strike. Closethe door and extend thedeadbolt several timesagainst the door frame.The strike centering indicator will leave a center mark on the doorframe to aid in locatingthe strike. (fig. 1)
Using reinforcing strike as a template, marklocations for reinforcing screws. (fig 3) Drilltwo 5/32" dia. pilot holes for the 3" longscrews and two 1/8" dia. pilot holes for the#8 x 3/4" screws. Mark drill points 5/16"above and below centering point. Bore two1" dia. holes 1-1/4" deep at these points.Chisel out holes for dust box. (fig. 4)
Position strike plate on centermark. Align and trace outsideof strike and mounting screwsonto the door frame. (fig. 2)
Chisel out thearea marked instep (2) 7/32"deep or until thestrike box, reinforcing strikeand strike platefits inside mortiseand flush withthe door frame.(fig. 5)
5 Install strike as illustrated.
Bore 1" dia. holeabove and belowcentering point.
Drill 1/8" dia. pilot holesfor # 8 screws.
Drill 5/32" dia. pilotholes for 3" screws.
5/16" abovecenter point.
5/16" below center point.
fig. 4
fig. 51. Dust Box2. Reinforcing Strike3. #8 x 3/4" Combination Screws (2)4. 3" Reinforcing Screws* (2)5. Strike Plate6. #8-32 x 1/4" Machine Screws (2)
*Note:Lubricant recommendedwhen installing 3" reinforcing screws.
TEAR HERE FOR ENGLISH.
OUTSIDE
INSIDE INSIDE
center line
