Installation peration Manual - Willoughby Industries
Transcript of Installation peration Manual - Willoughby Industries
Rev. 9/2021
Installation & Operation Manual
Willoughby Industries, Inc.5105 West 78th StreetIndianapolis, IN 46268Toll Free: (800) 428-4065Local: (317) 875-0830Fax: (317) 875-0837www.willoughby-ind.com MADE IN THE U.S.A.
WAF-5403 SeriesWAF-5404 Series
Aquafount® 54" 180° Solid Surface WashfountainElectronic/PneumaticTable of Contents
Pre-Installation Information �������������������������������������3Physical Dimensions ����������������������������������������������4Rough-In Dimensions ���������������������������������������������6Required Installation Supplies ��������������������������������9Parts List ���������������������������������������������������������������10Exploded-view Drawing ���������������������������������������� 11Hardware Identification Chart �������������������������������12Installation Instructions ���������������������������������������������
Step 1: Pedestal Mounting �������������������������������13Step 2: Mounting Basin ������������������������������������14Step 3: Drain Assembly �����������������������������������15Step 4A: Connections for Infrared/Piezo Actuators �������������������������������������������16Step 4B: Connections for Pneumatic Actuators ��������������������������������������������������������������������������17Step 5: Final Assembly ������������������������������������18
JACO Fitting Instructions ��������������������������������������19Mixing Valve Instructions ��������������������������������������20Infrared Sensor Installation Instructions ���������������21Liquid Soap Specification and Maintenance ���������22Care and Maintenance �����������������������������������������23Troubleshooting ��������������������������������������������������������
Infrared Sensors �����������������������������������������������24Electronic Valves ����������������������������������������������25Pneumatic Valves ���������������������������������������������26
Replacement Part Numbers ���������������������������������27Drawings �������������������������������������������������������������������
General Dimensions �����������������������������������������28Rough-in Dimensions ���������������������������������������30Valve Details �����������������������������������������������������32Miscellaneous Details ���������������������������������������41
Warranty ���������������������������������������������������������������45
* Wall mounted models only. Follow the applicable instructions in this manual to ensure installation complies with A.D.A. requirements.
WAF-5404
Page 2Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
(Page intentionally left blank)
(Page intentionally left blank)
Page 3Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
Pre-Installation Information
When installing the Willoughby Industries' WAF-5403/5404 Series washfountain system:
Before Step 1 of the installation instructions, ensure that rough-ins are in the correct location�
The valve assembly, including the spray head, MUST NOT BE connected until afterall lines have been flushed to remove the small particles of debris that are inherentwith new construction projects and all chemicals that are used in flushing are purgedfrom the system�
Chemicals used in flushing plumbing systems can attack the internal components ofthe valve and spray head and severely damage them, so any flushing of the systemmust be followed by a full flushing with pure water to clear any harsh chemicalsremaining in the system� Debris in the system if allowed to enter the valve assemblyand spray head can cause poor performance or outright failure�
Again DO NOT attempt to connect the valve assembly and spray head until after allflushing is complete and pure water is the only media that will be passing through thesystem� Damage to the valve assembly or spray head caused by harsh chemicals ordebris will not be covered by the manufacturer's warranty�
INSTALLATION INSTRUCTIONS
Visit our website at http.//www.willoughby-ind.com2210 West Morris Street • P.O. Box 21217 • Indianapolis, IN 46221
(317) 638-2381 • Fax: (317) 638-6110 • (800) 428-4065© Rev. 11/2007 Page 3
Installation notice!Check Rough-in location and flush lines prior to hook up!
When installing the Willoughby Industries’ WAW, WAF, or WWF serieswashfountains or lavatory deck systems:
Before Step 1 of the installation instructions, ensure that rough-ins are in the correctlocation.
It is essential that the water supply lines be thoroughly flushed prior to making finalconnection to the hot and cold water supply lines. These lines must be flushedsufficiently to remove the small particles of debris that are inherent with newconstruction projects. If this debris is not removed, the valving in these units will bedamaged. Do not attempt to remove aerators to flush debris into the lavatory. Thedamage can only be fixed by replacing the valves. Damage to valves caused by debriswill not be covered by the manufacturers warranty.
Installation notice!Check Rough-in location and flush lines prior to hook up!
© Rev. 5/2010
INSTALLATION INSTRUCTIONS
Visit our website at http.//www.willoughby-ind.com2210 West Morris Street • P.O. Box 21217 • Indianapolis, IN 46221
(317) 638-2381 • Fax: (317) 638-6110 • (800) 428-4065© Rev. 11/2007 Page 3
Installation notice!Check Rough-in location and flush lines prior to hook up!
When installing the Willoughby Industries’ WAW, WAF, or WWF serieswashfountains or lavatory deck systems:
Before Step 1 of the installation instructions, ensure that rough-ins are in the correctlocation.
It is essential that the water supply lines be thoroughly flushed prior to making finalconnection to the hot and cold water supply lines. These lines must be flushedsufficiently to remove the small particles of debris that are inherent with newconstruction projects. If this debris is not removed, the valving in these units will bedamaged. Do not attempt to remove aerators to flush debris into the lavatory. Thedamage can only be fixed by replacing the valves. Damage to valves caused by debriswill not be covered by the manufacturers warranty.
Installation notice!Check Rough-in location and flush lines prior to hook up!
© Rev. 5/2010
Check Rough-In location PRIOR to installation
Flush lines thoroughly PRIOR to hook-up
Check Rough-In location PRIOR to installation
Flush lines thoroughly PRIOR to hook-up
Pre-Installation Information
Page 4Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
Physical Dimensions- Floor-mounted Unit *WAF-5403-FL unit shown; WAF-5404-FL will have same pedestal dimensions.
Physical Dimensions- Floor-mounted Unit
Page 5Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
Physical Dimensions- Wall-mounted Unit *WAF-5404 unit shown; WAF-5403 will have same pedestal dimensions.
Physical Dimensions- Wall-mounted Unit
Page 6Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
Rough-in Dimensions- Floor-mounted Unit *WAF-5403-FL unit shown; WAF-5404-FL will have same rough-in dimensions.
Rough-in Dimensions- Floor-mounted Unit
Page 7Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
9-11/16"
17"
23-11/16" A.F.F.(FOR 34" A.D.A.
RIM HEIGHT)
NOTED
2 PLCS:
A5404-0026AS NOTED
1
Indianapolis, IndianaBEH
BEH 06-18-14
06-18-14AANGLE:
ASIZE:
54" SOLID SURFACE WASHFOUNTAIN - OFF FLOOR - 34" RIM HEIGHT
SHEET:REV.:
ORIG.:REVISION:
SCALE: 1:5FRACTIONS:EXCEPT AS
3 OF 3REF.:
TOLERANCES
TITLE / DESC.: WAF-5404 PART #:
MAT'L:3 PLCS:
0.030.0151/32"
Willoughby Industries, Inc.
STANDARD
RIM HEIGHT OF 34" AFF.
WATER SUPPLY
110V GFCI ELECTRICAL OUTLET
LOCATION OF THE 110 / 24 VAC
FINISHED FLOOR
CODES FOR THE MOUNTING CONSULT LOCAL ELECTRICAL
(EL1, IR ONLY)
FOR ALTERNATE RIM HEIGHT.ADJUST DIMENSIONS ACCORDINGLY
CLASS 2 TRANSFORMER
1/2" HOT AND COLD
NOTE:ROUGH-IN DIMENSIONS ARE FOR A
WALL MOUNTED ROUGH-IN SHOWN.FOR FLOOR MOUNTED ROUGH-IN, CONTACT FACTORY.
3-1/16"
5-9/16"
1-5/8"
12"
12-7/8"
7-13/16" 7-13/16"
26-1/2"
15-1/4"
4"
1-9/16"
4" 6" 11-1/4"
2-1/2"
20-3/8"
17X 5/16" THRU
7-3/4"
1-1/2" DRAIN 6-1/4"
15-3/8"
WILLOUGHBY
Rough-in Dimensions- Wall-mounted Unit *WAF-5404 unit shown; WAF-5403 will have same rough-in dimensions.
Rough-in Dimensions- Wall-mounted Unit
Page 8Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
(Page intentionally left blank)
(Page intentionally left blank)
Page 9Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
Required Installation Supplies
• Proper mounting hardware
• Hardware for waste oulet connections
• Gasket for waste outlet connection
• Shims (for installation if necessary)
• Supply piping
• Silicone caulk
• Plumbers putty
WARNING: Willoughby Industries does not assume any responsibility for personal injury or damage to equipment due to an improperly installed WAF-5403/5404 Series washfountain.
Required Installation Supplies
Page 10Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
Parts List
*XX REPRESENTS THE WASH FOUNTAIN COLOR
WHITE GRANITE=WG SAND STONE=SS GRAY GRANITE=GG BLACK GRANITE=BG SEA GREEN=SG NOCTURNAL BLUE=NB GLACIER WHITE=GW BONE=B
ITEM #
DESCRIPTION PART NUMBER (P/N) - 3-STATION
PART NUMBER (P/N)- 4-STATION
1 54" HALF-ROUND BASIN - SOLID SURFACE 800540C-XX* 800540C-XX*
2PEDESTAL ASSEMBLY (WALL-MOUNT) WAF5404-WA WAF5404-WAPEDESTAL ASSEMBLY (FLOOR-MOUNT) WAF5404-FL WAF5404-FL
3
ACTUATOR HOUSING / VALVE HEAD KIT - INFRARED WAF5403-I WAF5404-IACTUATOR HOUSING / VALVE HEAD KIT - PIEZO WAF5403-E WAF5404-EACTUATOR HOUSING / VALVE HEAD KIT - PNEUMATIC WAF5403-P WAF5404-PACTUATOR HOUSING / VALVE HEAD KIT - BATTERY OPERATED WAF5403-B WAF5404-B
4STND� SPRAY HEAD ASSEMBLY- WAF(AERATOR SPRAY HEAD, 0.5 GPM- #320157A)(SPRAY HEAD BASE, 45*- #800001)
320157A-ASMB 320157A-ASMB
5 TOP COVER- SOLID SURFACE 800333LP-XX* 800441LP-XX*6 DRAIN ASSEMBLY (WAF) 380281 3802817 VALVE BRACKET ADAPTER (WAF) S600417 S600417
8ACCESS COVER (WALL-MOUNT) S600481 S600481ACCESS COVER (FLOOR-MOUNT) S600171 S600171
9-12 HARDWARE KIT 800258 800258
NO
T SH
OW
N
INFRARED SENSOR 700150 700150PIEZO PUSHBUTTON 701179-C 701179-CACTUATOR PUSHBUTTON 600307 600307ELECTRONIC VALVE ASSEMBLY 803105-3EL 803105-4ELPNEUMATIC VALVE ASSEMBLY 803105-3PW 803105-4PWBATTERY OPERATED VALVE ASSEMBLY 803150-3BW 803105-4BWCHECKSTOP ASSEMBLY 980183 980183STAINLESS STEEL FLEX HOSE (6") 980506 980506STAINLESS STEEL FLEX HOSE (20") 980520 980520POWERS HYDROGUARD T/P (LFe480) 700480ELF 700480ELFPOWER SUPPLY - INFRARED 800137B 800138BPOWER SUPPLY - PIEZO 800139A 800140APLUG-IN TRANSFORMER - INFRARED 701210 701210PLUG-IN TRANSFORMER - PIEZO 701210 701211PNEUTRONIC TIMER 330043 330043
Parts List
Page 11Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
Exploded-view Drawing
ITEM # PART # DESCRIPTION QTY.1 800540C-XX 54" HALF ROUND BASIN 12 S600476 PEDESTAL - WALL MOUNT - 34" RIM 13 S600196 4 STATION HEAD ASSEMBLY 1
4 320157A-ASMB STANDARD SPRAY HEAD ASS'Y FOR WASHFOUNTAINS, 0.5 GPM 4
5 800441LP-XX 4 STATION TOP COVER - SOLID SURFACE 16 380281 WASHFOUNTAIN DRAIN ASSEMBLY, 1-1/2" NPSM 17 S600417 VALVE BRACKET ADAPTER - WWF / WAF 18 S600481 ACCESS COVER 19 800144 1/4-20 X 1/2" PHILLIPS TRUSS HEAD SCREW 710 4500NSS 1/4-20 X 1/2" BUTTON HEAD SECURITY SCREW 1211 800127 1/4-20 X 1-1/2" FH SECURITY SCREW 212 800113 TINNERMAN NUT 1/4-20, S/S 6
NOTE:TO ORDER REPLACEMENT SOLID SURFACE PARTS, SPECIFY DESIRED COLOR BY REPLACING "XX" IN PART NUMBER WITH CORRESPONDING COLOR CODE:
B BONEBG BLACK GRANITEGG GREY GRANITEGW GLACIER WHITENB NOCTURNAL BLUERC RED CORALSG SEA GREENSS SANDSTONEWG WHITE GRANITE
1
3
12
12
4
11
5
10
8
2
7
6
9
10
2 PLCS: BEH
BEH 06-18-14
06-18-14A 2 OF 3
AS NOTED
A5404-0026Indianapolis, Indiana
1:14NOTED
ASIZE:
54" SOLID SURFACE WASHFOUNTAIN - OFF FLOOR - 34" RIM HEIGHT
SHEET:REV.:
ORIG.:REVISION:
SCALE: REF.:1
3 PLCS:
PART #:
MAT'L:
FRACTIONS:
TOLERANCES EXCEPT AS
WAF-5404TITLE / DESC.:
ANGLE:
0.030.0151/32"
Willoughby Industries, Inc.
STANDARD
WILLOUGHBY
*WAF-5404 (wall-mounted) unit shown
Exploded-view Drawing
Page 12Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
Hardware Identification ChartINSTALLATION INSTRUCTIONS
Visit our website at http.//www.willoughby-ind.com2210 West Morris Street • P.O. Box 21217 • Indianapolis, IN 46221
(317) 638-2381 • Fax: (317) 638-6110 • (800) 428-4065© Rev. 1/2007 Page 11
HARDWAREIdentification Chart
© Rev. 5/2010
Hardware Identification Chart
Page 13Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
Parts supplied:
• Complete Unit (Pre-assembled)
•
Note: Hardware for wall anchoring by others.
Note: Use anchors that are adequate for the type of wall: drywall, concrete, metal studs, wood studs, etc.
Note: Refer to rough-in drawing for backplate mounting hole locations to achieve 34" rim height.
1�) Measure and mark the vertical centerline of the washfountain on the wall. Mark a level line at the height prescribed by the rough-in drawing for the pedestal backplate center hole. Drill a hole for a wall anchor (supplied by others) at this height mark. Make sure that the intended anchor locations will provide adequate backing to support the installed washfountain. If adequate backing does not exist, install appropriate support backing or relocate unit before proceeding with installation (backing provided by others).
2�) Mount the pedestal on the wall using a wall anchor through the backplate center hole and the first drilled hole. DO NOT TIGHTEN THIS FIRST WALL ANCHOR ALL THE WAY, as you may need to adjust the pedestal to ensure it is level�
3�) Make sure the pedestal is level and plumb against the wall, then mark and drill holes for the rest of the wall anchors as specified by the rough-in drawing.
4�) Ensure once more the pedestal is level, then secure it to the wall using the remaining anchors (supplied by others). Make sure all wall anchors are tight and secure against the pedestal backplate.
Note: Be sure backplate is level and plumb against the wall so that water in basin will drain correctly once assembly is completed.
Installation Instructions
PEDESTAL BACKPLATE
PEDESTAL BACKPLATECENTER HOLE
VALVE MOUNTING TAB
WALL ANCHORS(SUPPLIED BY OTHERS)
NOTE: FOR CLARITY OF WALL ANCHOR MOUNTING LOCATIONS, ONLY THE BACKPLATE PORTION OF THE PEDESTAL IS SHOWN.
Step 1: Pedestal Mounting
Installation Instructions
Page 14Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
Installation Instructions (cont.)
SECURITY SCREWS
SHIPPING BOLTS
ACTUATOR HOUSING
BASIN
(SUPPLIED BY OTHERS)WALL ANCHORS
PEDESTAL
1/4-20 X 1/2" PHILLIPS TRUSS HEAD SCREWS
TOP LEDGE
Step 2: Mounting BasinParts supplied:
• Solid Surface Basin
• Actuator Housing
• Pedestal Backplate
Removing the top cover. Mounting the basin and actuator housing to the backplate and wall.
1�) Remove top cover from the valve head kit by loosening the security screws as shown in the above-left diagram� Set the top cover, screws, and nuts aside�
2�) With the help of an assistant, place basin on top ledge of the pedestal assembly�
3�) Carefully mark mounting holes on wall through the basin, then remove the basin and drill the mounting holes�
4�) Replace the basin and valve head kit as shown in the above-right diagram.
5�) Fasten wall anchors (supplied by others) through the basin and valve head kit holes securely, but DO NOT OVERTIGHTEN; this can damage the solid surface basin and valve head kit.
6�) Secure the basin to the pedestal by fastening the1/4-20 x 1/2" Philips truss head screws up through the pedestal basin mounting ring into the threaded inserts on the bottom of the basin�
Note: BE SURE to use the truss head screws included with the washfountain. Using longer screws than those provided can damage the solid surface basin.
Installation Instructions
Page 15Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
Installation Instructions (cont.)Step 3: Drain AssemblyParts/Materials supplied:
• Solid surface basin
• Drain assembly (see diagram)
• Plumbers putty (supplied by others)
1�) As shown on the diagram, apply a small (approx� 1/4" dia. 6" long) strand of plumbers putty on the underside of the drain basket lip (putty supplied by others)� 2.) Insert the drain basket down through the basin drain hole�
3.) Secure the drain basket in place by fitting the rubber and stainless steel washers onto the drain assembly from the underside of the basin� Tighten the locknut onto the drain basket assembly, sandwiching the washers between the basin and locknut.
Note: Over-tightening the locknut or security screw can damage the solid surface basin and/or drain assembly components.
4.) Secure the drain cover to the drain basket using the provided screw�
WASHERS
Installation Instructions
Page 16Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
Installation Instructions (cont.)
Parts supplied:
• Valve Assembly (pre-installed)
• 3/8" x 4' Multi-Colored Water Lines
• Small Diameter Multi-Colored Pneumatic Tubing
• 1/4-20 x 1/2" security screws
• 1/4-20 tinnerman nuts
Note: Use wire tie mounts and wire ties to route and secure wiring. Wires are long enough to accommodate various routing paths. Longer tubes may need to be bundled with wire ties so they do not come in contact with sharp corners.
INSTALLATION INSTRUCTIONS
Visit our website at http.//www.willoughby-ind.com2210 West Morris Street • P.O. Box 21217 • Indianapolis, IN 46221
(317) 638-2381 • Fax: (317) 638-6110 • (800) 428-4065© Rev. 1/2007 Page 6
Parts supplied:
· Valve AssemblyPlug-In TransformerTerminal Block Plate4’ x 3/8" multi-colored water lines
· ¼-20 x ½” security screws· ¼-20 tinnerman nuts· Wire ties· Wire tie mounts (adhesive backed)
1.) Locate terminal block plate and attach to pedestal using ¼-20 x ½” security screws and tinnerman nuts.
2.) Locate the group of loose colored wires coming from the terminal block plate labeled “UPPER”.3.) Feed two like-colored wires into each of the actuator housing assembles.
Note: Use wire tie mounts and wire ties to route and secure wiring. Wires are long enough toaccommodate various routing paths. Longer wires may need to be bundled with wire ties so thatthey do not come in contact with sharp corners.
4.) Plug both like-colored wires into the actuator as shown above (either wire will work on eachconnector).
5.) Locate the 3/8" x 4’ colored tubing water lines. Match up the color of tubing with the color of wireand run the tubing into each of the actuator housings. Loosen the plastic nut and firmly push thetubing into the elbow connector located in each spray head. Tighten nut securely. Repeat foreach spray head, being sure to match each of the colors together (wire and tubing).
6.) Connect each set of like-colored wires and tubing to each of the manifolded valves.
STEP FOUR-AConnections for Infrared / Piezo Actuators
Infrared
Piezo
© Rev. 5/2010
Piezo Push Button Actuator
INSTALLATION INSTRUCTIONS
Visit our website at http.//www.willoughby-ind.com2210 West Morris Street • P.O. Box 21217 • Indianapolis, IN 46221
(317) 638-2381 • Fax: (317) 638-6110 • (800) 428-4065© Rev. 1/2007 Page 6
Parts supplied:
· Valve AssemblyPlug-In TransformerTerminal Block Plate4’ x 3/8" multi-colored water lines
· ¼-20 x ½” security screws· ¼-20 tinnerman nuts· Wire ties· Wire tie mounts (adhesive backed)
1.) Locate terminal block plate and attach to pedestal using ¼-20 x ½” security screws and tinnerman nuts.
2.) Locate the group of loose colored wires coming from the terminal block plate labeled “UPPER”.3.) Feed two like-colored wires into each of the actuator housing assembles.
Note: Use wire tie mounts and wire ties to route and secure wiring. Wires are long enough toaccommodate various routing paths. Longer wires may need to be bundled with wire ties so thatthey do not come in contact with sharp corners.
4.) Plug both like-colored wires into the actuator as shown above (either wire will work on eachconnector).
5.) Locate the 3/8" x 4’ colored tubing water lines. Match up the color of tubing with the color of wireand run the tubing into each of the actuator housings. Loosen the plastic nut and firmly push thetubing into the elbow connector located in each spray head. Tighten nut securely. Repeat foreach spray head, being sure to match each of the colors together (wire and tubing).
6.) Connect each set of like-colored wires and tubing to each of the manifolded valves.
STEP FOUR-AConnections for Infrared / Piezo Actuators
Infrared
Piezo
© Rev. 5/2010
Infrared Sensor Actuator
1.) Locate the terminal block plate and attach to the pedestal using 1/4-20 x 1/2" security screws and tinnerman nuts�
2.) Locate the group of loose colored wires coming from the terminal block plate labeled "UPPER".
3.) Feed 2 like-colored wires into each of the actuator housing assemblies (either the Infrared or Piezo assemblies, whichever applies to the installation).
4.) Plug both like-colored wires into the actuator as shown above (either wire will work on each connector)�
5.) Locate the 3/8" multi-colored water lines. Match the color of each water line with the corresponding color of wiring� Run the end of each water line up through the basin to the head kit. Match the color of each water line to the spray head assembly below each actuator. On each corresponding spray head, loosen the plastic nut on the plastic connector and firmly push the water line through the plastic nut into the fitting. Tighten the plastic nut to secure the water line to the spray head. Repeat for each remaining water line. (**see JACO Fitting Instructions on Page 19 for further detail)� 6.) Once all water lines have been attached to their corresponding spray heads, on each corresponding manifolded valve assembly, loosen the plastic nut on the plastic connector and firmly push the water line through the plastic nut into the fitting. Tighten plastic nut to secure the water line to the valve assembly� Repeat for each water line�
7.) Connect each set of like-colored wires to each of the manifolded valves.
Step 4A: Connections for Infrared/Piezo Actuators
Installation Instructions
Page 17Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
Installation Instructions (cont.)Step 4B: Connections for Pneumatic ActuatorsParts supplied:
• Valve Assembly (pre-installed)
• 3/8” x 4’ Multi-Colored Water Lines
• Small Diameter Multi-Colored Pneumatic Tubing
• 1/4-20 x 1/2" security screws
• 1/4-20 tinnerman nuts
Note: Use wire tie mounts and wire ties to route and secure tubing. Longer tubes may need to be bundled with wire ties so that do not come in contact with sharp corners.
1�) Locate the small multi-colored pneumatic tubing� Feed each one into each of the actuator housing assemblies�
2.) Plug each tube onto the hose barb on the back of the push button.
3.) Locate the 3/8" multi-colored water lines. Match the color of each water line with the corresponding color of tubing� Run the end of each water line up through the basin to the head kit. Match the color of each water line to the spray head assembly below each push button actuator. On each corresponding spray head, loosen the plastic nut on the plastic connector and firmly push the water line through the plastic nut into the fitting. Tighten the plastic nut to secure the water line to the spray head. Repeat for each remaining water line. (**see JACO Fitting Instructions on Page 19 for further detail)� 4.) Once all water lines have been attached to their corresponding spray heads, on each corresponding manifolded valve assembly, loosen the plastic nut on the plastic connector and firmly push the water line through the plastic nut into the fitting. Tighten plastic nut to secure the water line to the valve assembly� Repeat for each water line�
5.) Connect each set of like-colored tubing to each of manifolded valves.
Pneumatic Push Button (Similar 3-station unit shown)
Installation Instructions
Page 18Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
Step 5: Final AssemblyParts supplied:
• Solid Surface Top Cover
• Access Cover
• 1/4-20 Tinnerman Nut
• 1/4-20 x 1" Security Screw
• 1/4-20 x 1-1/2" Flat Head Security Screws
1�) Make all final plumbing connections to valve inlets using supplied flex hoses (flex hoses have shut-off valves attached that should be connected to the supply inlets).
2�) Once all of the connections in the actuator housings are complete, locate the transformer. NOTE: PLUG-IN TRANSFORMER (IF NEEDED) MUST BE USED WITH A GROUND FAULT INTERRUPT (GFCI) RECEPTACLE TO HELP PREVENT POSSIBLE ELECTRICAL SHOCK.
3�) Test the system for leaks (both supply and waste).
4�) Using 1/4-20 x 1-1/2" flat head security screws, attach top cover to the actuator housing.
5�) Using 1/4-20 x 1" security screws, attach shroud to the backplate.
Installation Instructions (cont.)
TOP COVER
1/4-20 X 1-1/2" FLAT HEAD SECURITY SCREW
1/4-20 X 1/2" SECURITY SCREW
ACCESS COVER
Installation Instructions
Page 19Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
INSTALLATION INSTRUCTIONS
Visit our website at http.//www.willoughby-ind.com2210 West Morris Street • P.O. Box 21217 • Indianapolis, IN 46221
(317) 638-2381 • Fax: (317) 638-6110 • (800) 428-4065© Rev. 11/2006
Note: It is not necessary to disassemble this fitting for application. Merely insert tubing to stop andtighten seal.
1. Cut tubing end squarely and remove the internal burrs.2. Insert the tubing through the back of the nut all the way through the nut assembly to the tube stopin the fitting body (see illustration). If the tubing does not enter the nut easily, loosen the nut one turnand reinsert the tubing all the way to the tube stop in the fitting body.3. Turn the nut hand tight.4. Wrench tighten the nut 1½ - 2 turns.5. All nuts must be retightened when the system reaches projected operating temperature.
Note: To ensure proper assembly, tubing MUST be fully inserted into the fitting body all the way tothe tube stop.Note: Squeaking sound when tightening nut is normal. For pipe threaded connections, Teflon tapemust be used.
JACO FittingInstructions
JACO Fitting Instructions
JACO Fitting Instructions
Page 20Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
Mixing Valve Instructions INSTALLATION INSTRUCTIONS
Visit our website at http.//www.willoughby-ind.com2210 West Morris Street • P.O. Box 21217 • Indianapolis, IN 46221
(317) 638-2381 • Fax: (317) 638-6110 • (800) 428-4065© Rev. 11/2007 Page 15
To Install
NOTE: Installation should be in accordance with accepted plumbing practices. Flush all piping thoroughly before installa-tion.1. Locate a suitable place for the tempering valve. Valve should
be accessible for service and adjustment and as close to the point-of-use as possible.
2. Connect hot and cold water to the supply valve using 1/2” NPT or 3/8” compression connections.
3. Connect outlet of tempering valve to fi xture(s) using 1/2”NPT or 3/8” compression connections.
4. Turn on hot and cold water supplies. If any leaks are observed, tighten connections as necessary to stop leaks before proceeding.
5. Turn on fi xture and allow water to fl ow for 2 minutes.Measure water temperature at outlet. If water is not at desired temperature, adjust as necessary.
Specifi cations
e480-00 .......................................................1/2" NPT (Rough Bronze)e480-01 .................................................... 1/2" NPT (Rough Chrome)e480-10 ...................................... 3/8"Compression (Rough Bronze)e480-11 ..................................... 3/8"Compression (Rough Chrome)Capacity: ................................................................. 4.0 gpm (15.0 l/m)Approach Temperature: ..........................5°F (2.8°C) above set pt.Max. Operating Pressure: ......................................125psi (862 kpa)Max. Static Pressure: .............................................125psi (862 kpa)Max. Hot Water Temperature: ....................................180°F (82°C)Temp. Adjustment Range: ............................................ ASSE Type T/P: 95 – 110°F (43-48°C) ................................................. ASSE Type T: 80 – 120°F (27-49°C)Minimum Flow: ........................................................ 0.5 gpm (2.2 l/m)Checks: ......................................................................................IntegralConstruction: ........................................................... Cast Brass BodyCertifi ed: ................................................................................CSA B125Listing .....................................................ASSE 1016-1996 (Type T/P) .............................................................................................ASSE 1070
To Adjust Temperature
1. Loosen locknut.2. Turn on fi xture and run water for at least two (2) minutes
to allow supply temperature to stabilize.3. Turn temperature stem counter-clockwise for hotter or
clockwise for colder outlet temperature.4. Tighten locknut to prevent accidental or unauthorized
temperature adjustment.5. Re-check outlet temperature.
Repair Kit
Motor Repair Kit ........................................................................480-270
HydroGuard® T/P Series e480Lavatory Combination Valve
Installation Instructions
IS-P-e480
Figure 1
Figure 2: Typical Installation
Outlet
Hot WaterInlet
Temperature Adjustment Stem
Locknut Cold WaterInlet
Advanced Thermal Activation
© Rev. 5/2010
Mixing Valve Instructions
Page 21Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
Infrared Sensor Installation Instructions
INSTALLATION ANDOPERATION MANUAL
TOLL FREE (800) 428-4065 / LOCAL (317) 875-0830 / FAX (317) 875-0837
PAGE 1© Rev. 9/2016 www.willoughby-ind.com
WILLOUGHBY Industries, Inc. 5105 WEST 78TH STREET / INDIANAPOLIS, IN 46268
WILLOUGHBY INDUSTRIESINFRARED LAVATORY SENSOR
DETECTION AND ACTIVATION• When the sensor detects a user, a slow
ashing red light appears in the sensor window.
• After 1 to 2 seconds of detection, the light ashes rapidly and the sensor immediately activates the solenoid valve to begin water ow.
• The solenoid valve remains open as long as the user is detected.
• The solenoid valve turns off when the user is no longer detected.
• The sensor is set to activate the solenoid for a maximum of 30 seconds before automati-cally shutting off.
• Note: sensor range is factory preset to 20".Optional range adjustment remote avail-able to adjust range from 1"min to 30"max.
INSTALLATION AND REPLACEMENT1. Disconnect 24V AC power at the transformer
or fuse box.2. Remove top cover to expose sensors.3. Install new sensor. Make sure sensor arrow is
pointing up. See Figure 1.4. Connect the red male power cable to the
red female connector on the sensor.See Figure 3.
5. Connect the black female solenoid cable to the black male connector on the sensor.See Figure 3.
6. Replace top cover removed in Step 2.7. Reconnect power.
PART#: 70015024V AC System IR Sensor
FIGURE 3- 24V AC SYSTEM IR ASSEMBLY
FIGURE 1- IR SENSOR
FIGURE 2- IR REMOTE
Infrared Sensor Installation Instructions
Page 22Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
(For models with “LSD” option only)
Liquid soap viscosity is measured in “cps” (centipoise). The liquid soap chosen to be used with Willoughby’s Liquid Soap Dispenser should be between 100cp and 2500cp.The viscosity of the soap should be thin and free flowing.Some soap types are available in a concentrate and must be diluted with water.
The pH (acidity) level should be in the range of 6.5 to 8.5.Soap which is too acidic (pH less than 6.5) can corrode stainless steel and degrade rubber, plastic, or chrome-plated materials.Soap that is outside the range of 6.5 - 8.5 might be harsh on the hands or skin.
(Generally, any quality soap meeting the viscosity and pH guidelines should work well.)
Recommended Maintenance Schedule
To maintain proper function, Willoughby’s Liquid Soap Dispenser should be cleaned periodically to remove soap residue. The Liquid Soap Spout should be soaked in hot water for a period of 30 minutes when cleaning is being performed. The soap tray should also be cleaned with hot water.
Liquid Soap Specification and Maintenance
Liquid Soap Specification and Maintenance
Page 23Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
Care and MaintenanceSolid Surface Care
Aquasurf® surfaces may be easily cleaned using conventional cleaning agents such as an ammonia based liquid cleaner, (glass cleaner).
Dry stains on a matte finish can be removed with a 3M Scotch-Brite gray scouring pad or a mild abrasive cleaner.
Burns or scorches can be removed by sanding with coarse grit sandpaper followed by finer grit (220) sandpaper. Follow sanding with a 3M Scotch-Brite gray pad (or equivalent) to match finish of sanding area to surrounding area. A final buffing may be required on polished surfaces. Accidental nicks or chips can be repaired with special patch kits available in all Aquasurf® colors.
Avoid exposing Aquasurf® surfaces to strong chemicals such as acetone’s; paint removers and sulfuric acid or hydrochloric chemical cleaners. Exposure to strong chemicals may result in permanent damage to Aquasurf® surfaces.
Stainless Steel Care
Stainless Steels are basically alloys of iron and chromium and are corrosion resistant. Stainless steel has a bright surface that is easy to clean and is free from oxides. Therefore, cleaning of stainless steel is relatively simple and easy if done on a regular basis.
Frequency of cleaning should depend on the rate at which the fixture becomes dirty. Remember that fresh (soft) deposits of all kinds are relatively easy to remove, while removing older (hard) deposits are much more difficult. Establish a cleaning SCHEDULE.
Routine cleaning should involve ordinary soap or detergent and water, applied with a sponge, brush or cloth. Baking soda, borax or any of several non-abrasive commercial cleansing agents can help hasten the cleaning action. After scrubbing, rinse THOROUGHLY and wipe dry.
DO NOT use common steel wool, scouring pads, scrapers, wire brushes, files or other steel tools to clean stainless steel. Such items will scratch the surface or leave small particles of iron imbedded in the surface, which will eventually rust and stain the surface - even appearing as if the stainless itself was rusting.
Certain chemical compounds, if used on stainless steel, can give the appearance of rust and if allowed to stand for long periods of time, can pit the surface of even stainless. Products containing hydrochloric acid, muriatic acid or potassium hydrochloride can ruin the surface.
Care and Maintenance
Page 24Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
Troubleshooting - Infrared SensorsI� Faucet does not function (red light does not appear when user steps in front of sensor)
A� No power to sensor. Make certain that power is on. Check transformer leads and connections. Repair or replace as necessary�
B� Willoughby 700150 IR Sensor not operating� Replace Willoughby 700150 IR Sensor�
II� Faucet does not function (red light appears when user steps in front of sensor and solenoid does not click)A� Debris in solenoid; disassemble, clean, and flush�B� Solenoid not wired correctly; check solenoid connections.C. Solenoid problem; replace solenoid�
III� No water when activated (valve clicks)A� Make certain that water is turned on.B� Valve clogged. Clean or replace filter.
IV� Very low flow or slow dribbleA� Check supply stop(s); open if closed.B� Debris in filter; remove, clean, and reinstall�C. Debris in aerator or spray head; remove, clean and reinstall�D� Disassemble solenoid; clean and flush�
V� Continues to run (with power on and red light flashing)A� Non-permanent target in range after user leaves� Remove non-permanent target� If this
target is a new permanent target (i�e�, a new wall or partition), turn off 24 volt power forfifteen (15) seconds. Turn power back on and let the sensor complete start-up mode�
B� Sensor failure; replace sensor�
VI� Continues to run (even with power disconnected)A� Solenoid valve installed backwards.B� Debris in solenoid, won’t close properly; remove operator and clean� Reassemble in the
same manner�
Troubleshooting - Infrared Sensors
Page 25Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
The two most common reasons an electronic valve does not operate properly are: (1) lack of power or (2) lack of water pressure. The following steps should be used as a guide in identifying the problem of a malfunctioning electronic valve.
I. Lack of powerA. Verify that the 110V GFCI outlet has powerB. Check all connections to ensure they have been made correctly:
1. Cable connecting the valve coil and the timer or IR sensor2. Cable connecting the timer and the pushbutton (Piezo only)3. Cable connecting the timing device and the 24VAC transformer4. The 24VAC transformer and the 110V GFCI outlet
C. If the valve is wired correctly, the solenoid will make a “click” sound indicating that the valve has been actuated. The electronic valve is actuated by either the piezo pushbutton or the triggering of the infrared sensor (see the Start-Up Instructions for Infrared Sensors in this manual).
II. Lack of water pressureA. Check the supply to the rough-insB. Make sure the screwdriver stops are in the open positionC. Water pressure needs to be above 35psi to operate the valve
1. If the water supply pressure is above 35psi but not exiting the valve:a. Clean any debris from the screen on the inlet side of the solenoid valve bodyb. Remove the screws on the valve body and clean any debris from the diaphragm
After all of the above steps have been followed, if there is still no water coming out of the spray head, there may be a damaged or defective part (see installation notice in the beginning of this manual).
Troubleshooting - Electronic Valves
Troubleshooting - Electronic Valves
Page 26Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
I. Valve will not open or deliver waterA. Check the plastic tubing that runs from the pushbutton actuator to the pneumatic valve for
air leaks.B. Make sure the checkstop on the supply to the valve is fully open. Do not partially close the
checkstop for any reason as it is not a throttling valve. The checkstop should be fully open (normal operation) or fully closed (when servicing the valve).
C. Close checkstop and then inspect the strainer in the supply line (installed after the checkstop) to make sure the strainer is not blocked or partially blocked, prohibiting water flow.
II. Valve will not shut offA. Separate valve motor from casting by removing the four (4) #8 screws.B. Inspect the water diaphragm assembly to see if bypass hole in diaphragm is blocked.
Remove any debris by blowing on diaphragm or using force of air. Do not use any tool (such as straight pin) to remove any debris. Enlarging the hole will shorten or make for erratic cycling.
C. Check the metering screw on the timer assembly to make sure the adjustment screw is not closed too tightly. To reset, back out adjustment screw (counterclockwise) about 1-1/2” turns, and adjust for the desired cycle.
III. Valve continues to trickle or partially deliver water after cycle is overA. Inspect seating area on valve base to make sure no debris, pitting, or scoring is present.B. Clean seat or replace seat as necessary.C. Inspect seating area of diaphragm for debris, clean as necessary. If debris has caused
permanent indentations in the rubber, it may have to be replaced.
After all of the above steps have been followed, if there is still no water coming out of the spray head, there may be a damaged or defective part (see installation notice in the beginning of this manual).
Troubleshooting - Pneumatic Valves
Troubleshooting - Pneumatic Valves
Page 27Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
Replacement Part Numbers*XX REPRESENTS THE WASH FOUNTAIN COLOR
B = BONE BG = BLACK GRANITEGG = GREY GRANITEGW = GLACIER WHITENB = NOCTURNAL BLUERC = RED CORALSG = SEA GREENSS = SAND STONEWG = WHITE GRANITE
Table 1 – Replacement part numbers for general assembly:
PART #DESCRIPTION WAF-5403 WAF-5404
SOLID SURFACE BASIN 800540C-XX*SOLID SURFACE TOP COVER 800333LP-XX* 800441LP-XX*PEDESTAL ASSEMBLY - WALL MOUNT WAF5404-WAPEDESTAL ASSEMBLY - ON FLOOR WAF5404-FLHARDWARE KIT 800258STND� SPRAY HEAD ASSEMBLY- WAF(AERATOR SPRAY HEAD, 0.5 GPM- #320157A)(SPRAY HEAD BASE, 45*- #800001)
320157A-ASMB
Table 2 – Replacement part numbers for models with Infrared Actuation:
PART #DESCRIPTION WAF-5403 WAF-5404
VALVE HEAD KIT - INFRARED WAF5403-I WAF5404-IVALVE ASSEMBLY - ELECTRONIC 803105-3EW 803105-4EWPOWER SUPPLY 800137B 800138BPLUG-IN TRANSFORMER 701210INFRARED SENSOR 700150
Table 3 – Replacement part numbers for models with Piezo Actuation:
PART #DESCRIPTION WAF-5403 WAF-5404
VALVE HEAD KIT - PIEZO WAF5403-E WAF5404-EVALVE ASSEMBLY - ELECTRONIC 803105-3EW 803105-4EWPUSHBUTTON - PIEZO 701179-CPOWER SUPPLY 800139A 800140APLUG-IN TRANSFORMER 701210 701211PNEUTRONIC TIMER 330043
Table 4 – Replacement part numbers for models with Pneumatic Actuation:
PART #DESCRIPTION WAF-5403 WAF-5404
VALVE HEAD KIT - PNEUMATIC WAF5403-P WAF5404-PVALVE ASSEMBLY - PNEUMATIC 803105-3PW 803105-4PWPUSHBUTTON - PNEUMATIC 600307
Replacement Part Numbers
Page 28Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
DR
AWIN
G:
Gen
eral
Dim
ensi
ons
Replacement Part Numbers
Page 29Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
IN C
OM
PLI
AN
CE
WIT
H A
.D.A
. 201
0
54"
28-
5/8"
FIN
ISH
ED
FLO
OR
26-1
/2"
BO
WL
DE
PTH
9-1
1/16
"
8-1/
4"
16-
1/16
"
FIN
ISH
ED
FLO
OR
FOR
A.D
.A.
34"
MA
X A
.F.F
.
5-5
/8"
AS N
OTE
D
1
PA
RT
#:W
AF-
5404
BE
HE
XC
EP
T A
S
3 P
LCS
:
AN
GLE
:
A54
04-0
026
NO
TED
2 P
LCS
:
1 O
F 3
SC
ALE
:R
EF.
:
MA
T'L:
TITL
E / D
ESC
.:
TOLE
RAN
CES
FRAC
TIO
NS:
ASI
ZE:
1:16
REV
ISIO
N:
AB
EH
54" S
OLI
D S
UR
FAC
E W
AS
HFO
UN
TAIN
- O
FF F
LOO
R -
34" R
IM H
EIG
HT
OR
IG.:
REV
.:06
-18-
14
Indi
anap
olis
, Ind
iana
SH
EE
T:
06-1
8-14
0.03
0.01
51/
32"
Will
ough
by In
dust
ries
, Inc
.
STAN
DAR
D
WIL
LOU
GH
BY
DR
AWIN
G:
Gen
eral
Dim
ensi
ons
Replacement Part Numbers
Page 30Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
DR
AWIN
G:
Rou
gh-in
Dim
ensi
ons
DET
AIL
: DW
G#
P139
008A
Replacement Part Numbers
Page 31Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
9-1
1/16
"
17"
23-1
1/16
" A.F
.F.
(FO
R 3
4" A
.D.A
.R
IM H
EIG
HT)
NO
TED
2 P
LCS
:
A54
04-0
026
AS N
OTE
D
1
Indi
anap
olis
, Ind
iana
BE
H
BE
H06
-18-
14
06-1
8-14
AA
NG
LE:
ASI
ZE:
54" S
OLI
D S
UR
FAC
E W
AS
HFO
UN
TAIN
- O
FF F
LOO
R -
34" R
IM H
EIG
HT
SH
EE
T:R
EV.:
OR
IG.:
REV
ISIO
N:
SC
ALE
:1:
5FR
ACTI
ON
S:E
XC
EP
T A
S
3 O
F 3
RE
F.:
TOLE
RAN
CES
TITL
E / D
ESC
.:W
AF-
5404
PA
RT
#:
MA
T'L:
3 P
LCS
:0.
030.
015
1/32
"
Will
ough
by In
dust
ries
, Inc
.
STAN
DAR
D
RIM
HE
IGH
T O
F 34
" AFF
.
WA
TER
SU
PP
LY
110V
GFC
I ELE
CTR
ICA
L O
UTL
ET
LOC
ATI
ON
OF
THE
110
/ 24
VA
C
FIN
ISH
ED
FLO
OR
CO
DE
S F
OR
TH
E M
OU
NTI
NG
C
ON
SU
LT L
OC
AL
ELE
CTR
ICA
L (E
L1, I
R O
NLY
)
FOR
ALT
ER
NA
TE R
IM H
EIG
HT.
AD
JUS
T D
IME
NS
ION
S A
CC
OR
DIN
GLY
CLA
SS
2 T
RA
NS
FOR
ME
R
1/
2" H
OT
AN
D C
OLD
NO
TE:
RO
UG
H-IN
DIM
EN
SIO
NS
AR
E F
OR
A
WA
LL M
OU
NTE
D R
OU
GH
-IN S
HO
WN
.FO
R F
LOO
R M
OU
NTE
D R
OU
GH
-IN,
CO
NTA
CT
FAC
TOR
Y.
3-1
/16"
5-9
/16"
1-5
/8"
12"
12-
7/8"
7-1
3/16
" 7
-13/
16"
26-
1/2"
15-
1/4"
4"
1-9
/16"
4"
6"
11-
1/4"
2-1
/2"
20-
3/8"
17X
5
/16"
TH
RU
7-3
/4"
1-1/
2" D
RA
IN
6
-1/4
"
15-
3/8"
WIL
LOU
GH
BY
DR
AWIN
G:
Rou
gh-in
Dim
ensi
ons
Replacement Part Numbers
Page 32Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
7
4
8
1
2
3
5
9
10
11
6
NO
TE:
PAR
T #1
2 FL
EXH
OSE
, 20"
NO
T SH
OW
N
2 Pl
aces
+/-
.03
3 Pl
aces
+/-
.015
Frac
tions
+/-
1/32
"
Will
ough
by In
dust
ries
Inc.
Indi
anap
olis
, Ind
iana
Tole
ranc
esEx
cept
as
Title
or P
art D
escr
iptio
n:
Mat
eria
l:D
raw
n By
:D
ate:
Rev
isio
n #:
Dra
win
g #: Ap
prov
ed B
y:
VALV
E AS
SY, W
ASH
FOU
NT
3-ST
ATIO
N (E
L)
TRB
11/7
/11
B
8031
05-3
EW
Job
Nam
e:Pa
rt N
umbe
r:N
/A
Scal
e:1:
8Q
ty:
Shee
t:1
Of 1
N/A
Not
edAn
gle
+/- 1
ITEM
NO
.PA
RT
#D
ESC
RIP
TIO
NQ
TY.
170
0480
E P
ower
s 48
0E M
ixin
g Va
lve
12
9805
06FL
EXH
OSE
, 6"
13
8001
33#1
0-16
SEL
F TA
P TY
PE B
HEX
HEA
D S
CR
EW8
498
0183
CH
ECKS
TOP
ASSE
MBL
Y1
598
0501
3PM
1-M
A3 V
alve
Bra
cket
- Pl
astic
16
9801
64O
-RIN
G, #
015
4
798
0408
E1L
VALV
E AS
SEM
BLY
2
898
0197
PLAS
TIC
VAL
VE C
OU
PLIN
G2
998
0600
AVA
LVE
FITT
ING
ASS
EMBL
Y, 3
/8" E
LBO
W3
1098
0140
SPR
ING
CLI
P8
1198
0408
PRE1
L VA
LVE
ASSE
MBL
Y, R
IGH
T - P
LUG
GED
PO
RT
112
9805
20FL
EXH
OSE
, 20"
(NO
T SH
OW
N)
2
WIL
LOU
GH
BY
DR
AWIN
G:
Elec
tron
ic V
alve
Det
ail
Replacement Part Numbers
Page 33Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
2 Pl
aces
+/-
.03
3 Pl
aces
+/-
.015
Frac
tions
+/-
1/32
"
Will
ough
by In
dust
ries
Inc.
Indi
anap
olis
, Ind
iana
Tole
ranc
esEx
cept
as
Title
or P
art D
escr
iptio
n:
Mat
eria
l:D
raw
n By
:D
ate:
Rev
isio
n #:
Dra
win
g #: Ap
prov
ed B
y:
VAVL
E AS
SY, W
ASH
FOU
NT
4-ST
ATIO
N (E
L)
TRB
11/7
/11
B
8031
05-4
EW
Job
Nam
e:Pa
rt N
umbe
r:N
/A
Scal
e:1:
8Q
ty:
Shee
t:1
Of 1
N/A
Not
edAn
gle
+/- 1
ITEM
#PA
RT
#D
ESC
RIP
TIO
NQ
TY.
170
0480
E P
ower
s 48
0E M
ixin
g Va
lve
12
9805
06FL
EXH
OSE
, 6"
13
8001
33#1
0-16
SEL
F TA
P TY
PE B
HEX
HEA
D S
CR
EW10
498
0183
CH
ECKS
TOP
ASSE
MBL
Y1
598
0501
4PM
1-M
A4 V
alve
Bra
cket
- Pl
astic
16
9804
08E1
L VA
LVE
ASSE
MBL
Y3
798
0197
PLAS
TIC
VAL
VE C
OU
PLIN
G3
898
0164
O-R
ING
, #01
56
998
0600
AVA
LVE
FITT
ING
ASS
EMBL
Y, 3
/8" E
LBO
W4
1098
0140
SPR
ING
CLI
P11
1198
0408
PRE1
L VA
LVE
ASSE
MBL
Y, R
IGH
T - P
LUG
GED
PO
RT
112
9805
20FL
EXH
OSE
, 20"
(NO
T SH
OW
N)
2
11
3
4
6
PAR
T #1
2 - F
LEXH
OSE
, 20"
NO
T SH
OW
NN
OTE
:1
10
7
2
5
9
8
WIL
LOU
GH
BY
DR
AWIN
G:
Elec
tron
ic V
alve
Det
ail
Replacement Part Numbers
Page 34Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
TOLE
RAN
CES
FRAC
TIO
NS:
ATR
B
TRB
03/1
5/11
09/2
3/09
E1
OF
1
STAN
DAR
D
9804
08
1:2
PAR
T #:
E1L
VALV
E AS
SEM
BLY
(ALL
PO
RTS
OPE
N)
SHEE
T:R
EV�:
OR
IG.:
REV
ISIO
N:
SCAL
E:R
EF�:
MAT
'L:
Indi
anap
olis
, Ind
iana
NO
TED
EXC
EPT
AS
ANG
LE:
TITL
E / D
ESC
.:
3 PL
CS:
Will
ough
by In
dust
ries
Inc.
2 PL
CS:
0�03
0�01
51/
32"
1
SIZE
:
PAR
TS L
ISTE
D IN
TH
E PV
K R
EPAI
R
KITS
AR
E N
OT
SOLD
IND
IVID
UAL
LY
NO
TE:
REP
AIR
KIT
OR
DER
ING
#'S
AR
E LI
STED
IN T
HE
EXPL
OD
ED V
IEW
.
NO
TE:
ITEM
#PA
RT
#D
ESC
RIP
TIO
NQ
TY.
198
0420
SIN
GLE
TEM
P BA
SE w
/INSE
RTS
(ALL
PO
RTS
OPE
N)
12
9803
05W
ATER
SID
E D
IAPH
RAG
M/A
DAP
TOR
ASS
Y.1
398
0565
ARM
ATU
RE
BUM
PER
ASS
EMBL
Y, E
L VA
LVE
14
9805
33SP
RIN
G, 5
/8 2
4v V
ALVE
15
9805
30AR
MAT
UR
E C
AP, 2
4v V
ALVE
16
9801
70A
#8-3
2 x
1/2
" SC
REW
47
9805
32C
OIL
, 24V
DC
18
9805
34N
YLO
N N
UT,
5/1
6-18
1
5
6
2
PVK-
3
(2-8
) PLU
S (*
) BEL
OW
* EVK
-4 K
IT IN
CLU
DES
3808
97 V
ALVE
SEA
T W
/ 0-R
ING
(NO
T SH
OW
N)
8
1
7
33
4
EVK-
4 KI
T
2
EXPL
OD
ED V
IEW
ASSE
MBL
ED V
IEW
WIL
LOU
GH
BY
DR
AWIN
G:
Elec
tron
ic V
alve
Det
ail
Replacement Part Numbers
Page 35Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
PAR
T #1
2 FL
EXH
OSE
, 20"
NO
T SH
OW
NN
OTE
:
ITEM
NO
.PA
RT#
DES
CR
IPTI
ON
QTY
.1
7004
80E
Pow
ers
480E
Mix
ing
Valv
e1
298
0506
FLEX
HO
SE, 6
"1
380
0133
#10-
16 S
ELF
TAP
TYPE
B H
EX H
EAD
SC
REW
84
9805
013
PM1-
MA3
Val
ve B
rack
et -
Plas
tic1
598
0183
CH
ECKS
TOP
ASSE
MBL
Y1
698
0406
RPN
EUM
ATIC
VAL
VE A
SSEM
BLY
27
9801
97PL
ASTI
C V
ALVE
CO
UPL
ING
28
9801
64O
-RIN
G, #
015
49
9804
06PR
PNEU
MAT
IC V
ALVE
ASS
EMBL
Y, R
IGH
T - P
LUG
GED
PO
RT
110
9801
40SP
RIN
G C
LIP
811
9806
00A
VALV
E FI
TTIN
G A
SSEM
BLY,
3/8
" ELB
OW
312
9805
20FL
EXH
OSE
, 20"
(NO
T SH
OW
N)
2
10
9
6
7
1
2
5
3
4
11
8
2 Pl
aces
+/-
.03
3 Pl
aces
+/-
.015
Frac
tions
+/-
1/32
"
Will
ough
by In
dust
ries
Inc.
Indi
anap
olis
, Ind
iana
Tole
ranc
esEx
cept
as
Title
or P
art D
escr
iptio
n:
Mat
eria
l:D
raw
n By
:D
ate:
Rev
isio
n #:
Dra
win
g #: Ap
prov
ed B
y:
VALV
E AS
SY, W
ASH
FOU
NT
3-ST
ATIO
N (P
NEU
MAT
IC)
TRB
11/7
/11
B
8031
05-3
PW
Job
Nam
e:Pa
rt N
umbe
r:N
/A
Scal
e:1:
8Q
ty:
Shee
t:1
Of 1
N/A
Not
edAn
gle
+/- 1
WIL
LOU
GH
BY
DR
AWIN
G:
Pneu
mat
ic V
alve
Det
ail
Replacement Part Numbers
Page 36Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
PAR
T #1
2 - F
LEXH
OSE
, 20"
NO
T SH
OW
NN
OTE
:
ITEM
NO
.PA
RT
#D
ESC
RIP
TIO
NQ
TY.
170
0480
E P
ower
s 48
0E M
ixin
g Va
lve
12
9805
06FL
EXH
OSE
, 6"
13
8001
33#1
0-16
SEL
F TA
P TY
PE B
HEX
HEA
D S
CR
EW10
498
0501
4PM
1-M
A4 V
alve
Bra
cket
- Pl
astic
15
9801
83C
HEC
KSTO
P AS
SEM
BLY
16
9804
06R
PNEU
MAT
IC V
ALVE
ASS
EMBL
Y3
798
0164
O-R
ING
, #01
56
898
0197
PLAS
TIC
VAL
VE C
OU
PLIN
G3
998
0600
AVA
LVE
FITT
ING
ASS
EMBL
Y, 3
/8" E
LBO
W4
1098
0140
SPR
ING
CLI
P11
1198
0406
PRPN
EUM
ATIC
VAL
VE A
SSEM
BLY,
RIG
HT
- PLU
GG
ED P
OR
T1
1298
0520
FLEX
HO
SE, 2
0" (N
OT
SHO
WN
)2
6
11
1
8
10
2
3
4
59
7
2 Pl
aces
+/-
.03
3 Pl
aces
+/-
.015
Frac
tions
+/-
1/32
"
Will
ough
by In
dust
ries
Inc.
Indi
anap
olis
, Ind
iana
Tole
ranc
esEx
cept
as
Title
or P
art D
escr
iptio
n:
Mat
eria
l:D
raw
n By
:D
ate:
Rev
isio
n #:
Dra
win
g #: Ap
prov
ed B
y:
VAVL
E AS
SY, W
ASH
FOU
NT
4-ST
ATIO
N (P
NEU
MAT
IC)
TRB
11/7
/11
B
8031
05-4
PW
Job
Nam
e:Pa
rt N
umbe
r:N
/A
Scal
e:1:
8Q
ty:
Shee
t:1
Of 1
N/A
Not
edAn
gle
+/- 1
WIL
LOU
GH
BY
DR
AWIN
G:
Pneu
mat
ic V
alve
Det
ail
Replacement Part Numbers
Page 37Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
NOTE
:
PAR
TS L
ISTE
D IN
TH
E PV
K R
EPAI
R
KITS
AR
E N
OT
SOLD
IND
IVID
UAL
LYNOTE
:
REP
AIR
KIT
OR
DER
ING
#'S
AR
E LI
STED
IN T
HE
EXPL
OD
ED V
IEW
.
ITEM
#PA
RT
#D
ESC
RIP
TIO
NQ
TY.
198
0420
SIN
GLE
TEM
P BA
SE w
/INSE
RTS
(ALL
PO
RTS
OPE
N)
12
9803
05W
ATER
SID
E D
IAPH
RAG
M/A
DAP
TOR
ASS
Y.1
398
0310
WAT
ER S
IDE
DIS
K AS
SEM
BLY
14
9801
36SP
RIN
G, W
ATER
SID
E D
IAPH
RAG
M1
598
0126
BAR
RIE
R C
UP
16
9801
27O
-RIN
G M
1.5x
32 B
UN
A-70
17
9804
10M
ETER
ING
VAL
VE B
OD
Y AS
SEM
BLY
18
9801
35SP
RIN
G, A
IR S
IDE
MAG
NET
19
9804
05M
ETER
ING
VAL
VE M
AGN
ET/C
UP
ASSE
MBL
Y1
1098
0130
DIA
PHR
AGM
, AIR
SID
E, P
NEU
MAT
IC M
ETER
ING
VAL
VE1
1198
0134
AIR
SID
E SP
RIN
G1
1238
0801
MAI
R S
IDE
TOP
CO
VER
113
9800
01A
#8-3
2 x
1 1/
4" S
CR
EW4
PVK-
1M, P
VK-2
, & P
VK-3
PAR
TS A
RE
AVAI
LABL
E IN
KIT
FO
RM
ON
LY.
NOTE
:
TOLE
RAN
CES
FRAC
TIO
NS:
MW
AA
9804
06R
10/1
8/12
8/31
/16
TRB
STAN
DAR
D
1 O
F 1
1:2.
5
PAR
T #:
PNEU
MAT
IC M
ETER
ING
VAL
VE A
SSEM
BLY
- (R
IGH
T)
SHEE
T:R
EV.:
OR
IG.:
REV
ISIO
N:
SCAL
E:R
EF.:
MAT
'L:
Indi
anap
olis
, Ind
iana
NO
TED
EXC
EPT
AS
ANG
LE:
TITL
E / D
ESC
.:
3 PL
CS:
Will
ough
by In
dust
ries
Inc.
2 PL
CS:
0.03
0.01
51/
32"
1
SIZE
:
22
13
12
10
11
7
8
3
7 7
3
6
5
4
99
77
1
EXPL
OD
ED V
IEW
PVK-
2(P
ART#
: 2-4
)
PVK-
3(P
ART#
: 2)
PVK-
4M(IN
CLU
DES
KIT
SPV
K-1M
& P
VK-2
)
PVK-
1M(P
ART#
: 5-1
2)
↑
THR
U
VIEW
FR
OM
BO
TTO
M O
F VA
LVE
INLE
T /
OU
TLET
INLE
T /
THR
U
ASSE
MBL
ED V
IEW
WIL
LOU
GH
BY
DR
AWIN
G:
Pneu
mat
ic V
alve
Det
ail
Replacement Part Numbers
Page 38Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
D
RAW
ING
: 9V
Bat
tery
Ope
rate
d Va
lve
Det
ail
9
8
4
1
5
3
11
2
67
10
NO
TE:
PAR
T #9
8052
0 FL
EXH
OSE
, 20"
NO
T SH
OW
N
ITEM
NO
.PA
RT
#D
ESC
RIP
TIO
NQ
TY.
198
0501
3PM
1-M
A3 V
ALVE
BR
ACKE
T1
298
0183
CH
ECKS
TOP
ASSE
MBL
Y1
398
0140
SPR
ING
CLI
P, R
OU
ND
84
8001
33#1
0-16
SEL
F TA
P TY
PE B
HEX
HEA
D S
CR
EW8
598
0600
AVA
LVE
FITT
ING
ASS
EMBL
Y, 3
/8" E
LBO
W3
698
0197
PLAS
TIC
VAL
VE C
OU
PLIN
G2
798
0164
O-R
ING
, #01
54
898
0506
6" F
LEX
HO
SE, 1
/2 F
.I.P
CO
NN
ECTI
ON
19
7004
80E
POW
ERS
LFe4
80 M
IXIN
G V
ALVE
110
9804
16VA
LVE
ASSE
MBL
Y, B
ATTE
RY
OPE
RAT
ED2
1198
0416
PRVA
LVE
ASSY
, BAT
TER
Y O
PER
ATED
, RH
PLU
GG
ED P
OR
T1
1298
0520
20" F
LEX
HO
SE, 1
/2 F
.I.P
CO
NN
ECTI
ON
2
NAL
NAL
4/16
/21
4/16
/21
A1
OF
11:
3
SEE
BOM
PAR
T #:
VALV
E AS
SY, W
ASH
FOU
NT
3-ST
ATIO
N (B
O)
SHEE
T:R
EV.:
OR
IG.:
REV
ISIO
N:
SCAL
E:R
EF.:
MAT
'L:
TITL
E / D
ESC
.:
TOLE
RAN
CES
EX
CEP
T AS
N
OTE
D
2 PL
CS:
3 PL
CS:
FRAC
TIO
NS:
ANG
LE:
0.03
0.01
51/
4"1
ASI
ZE:
Will
ough
by In
dust
ries
, Inc
.In
dian
apol
is, I
ndia
naST
AND
ARD
8031
05-3
BW
Replacement Part Numbers
Page 39Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
D
RAW
ING
: 9V
Bat
tery
Ope
rate
d Va
lve
Det
ail
11
10
4
1
6
3
9
2
7
8
5
NO
TE:
PAR
T #9
8052
0 FL
EXH
OSE
, 20"
NO
T SH
OW
N
ITEM
NO
.PA
RT
#D
ESC
RIP
TIO
NQ
TY.
198
0501
4PM
1-M
A4 V
ALVE
BR
ACKE
T1
298
0183
CH
ECKS
TOP
ASSE
MBL
Y1
398
0140
SPR
ING
CLI
P, R
OU
ND
114
8001
33#1
0-16
SEL
F TA
P TY
PE B
HEX
HEA
D S
CR
EW10
598
0416
VALV
E AS
SEM
BLY,
BAT
TER
Y O
PER
ATED
36
9806
00A
VALV
E FI
TTIN
G A
SSEM
BLY,
3/8
" ELB
OW
47
9801
97PL
ASTI
C V
ALVE
CO
UPL
ING
38
9801
64O
-RIN
G, #
015
69
9804
16PR
VALV
E AS
SY, B
ATTE
RY
OPE
RAT
ED, R
H P
LUG
GED
PO
RT
110
9805
066"
FLE
X H
OSE
, 1/2
F.I.
P C
ON
NEC
TIO
N1
1170
0480
EPO
WER
S LF
e480
MIX
ING
VAL
VE1
1298
0520
20" F
LEX
HO
SE, 1
/2 F
.I.P
CO
NN
ECTI
ON
2
NAL
NAL
4/16
/21
4/16
/21
A1
OF
11:
4
PAR
T #:
VALV
E AS
SY, W
ASH
FOU
NT
4-ST
ATIO
N (B
O)
SHEE
T:R
EV.:
OR
IG.:
REV
ISIO
N:
SCAL
E:R
EF.:
MAT
'L:
TITL
E / D
ESC
.:
TOLE
RAN
CES
EX
CEP
T AS
N
OTE
D
2 PL
CS:
3 PL
CS:
FRAC
TIO
NS:
ANG
LE:
0.03
0.01
51/
4"1
ASI
ZE:
Will
ough
by In
dust
ries
, Inc
.In
dian
apol
is, I
ndia
naST
AND
ARD
8031
05-4
BW
Replacement Part Numbers
Page 40Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
4
3
2
1
6
5
7
PVK-
3 KI
T (IT
EM #
: 2)
BVK-
4
ITEM
#PA
RT
#D
ESC
RIP
TIO
NQ
TY.
198
0420
RSI
NG
LE T
EMP
BASE
w/IN
SER
TS -
PLU
GG
ED P
OR
T1
298
0305
WAT
ER S
IDE
DIA
PHR
AGM
/AD
APTO
R A
SSY.
13
9801
14C
OIL
AD
APTE
R, E
1L V
ALVE
14
9801
70A
#8-3
2 x
1/2
" SC
REW
W/S
EMS
SPLI
T L/
W4
598
0164
O-R
ING
, #01
51
670
0255
CO
IL A
SSEM
BLY,
9VD
C L
ATC
HIN
G, B
ATTE
RY
OPE
RAT
ED1
798
0680
WAS
HER
, NYL
ON
, 0.7
5"ID
, 1.0
0"O
D1
EEF
MW
10/1
2/16
11/3
0/15
A1
OF
11:
2
SEE
BOM
PAR
T #:
VALV
E AS
SY, B
ATTE
RY
OPE
RAT
ED, R
H P
LUG
GED
PO
RT
SHEE
T:R
EV.:
OR
IG.:
REV
ISIO
N:
SCAL
E:R
EF.:
MAT
'L:
TITL
E / D
ESC
.:
TOLE
RAN
CES
EX
CEP
T AS
N
OTE
D
2 PL
CS:
3 PL
CS:
FRAC
TIO
NS:
ANG
LE:
0.03
0.01
51/
32"
1
ASI
ZE:
Will
ough
by In
dust
ries
, Inc
.In
dian
apol
is, I
ndia
naST
AND
ARD
9804
16PR
D
RAW
ING
: 9V
Bat
tery
Ope
rate
d Va
lve
Det
ail
Replacement Part Numbers
Page 41Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
PIEZ
O H
EAD
KIT
DET
AIL
DR
AWIN
G:
Push
butto
n D
etai
lReplacement Part Numbers
Page 42Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
6
2
3
4
5
7
1
ITEM
#PA
RT
#D
ESC
RIP
TIO
NQ
TY.
160
0307
RK
REP
AIR
KIT
FO
R D
IAPH
RAG
M P
USH
BUTT
ON
PU
MP
12
380
840
FITT
ING
, HO
SE B
ARB,
PU
SH-IN
, 1/1
6" (B
RAS
S)1
3 3
8050
6MA
BOD
Y, P
USH
BU
TTO
N D
IAPH
RAG
M P
UM
P,M
OLD
ED1
4 6
0020
1D
IAPH
RAG
M, P
NEU
MAT
IC P
UM
P1
5 3
8050
4MA
CAP
, DIA
PHR
AGM
PU
MP,
MO
LDED
16
6000
57PU
SHBU
TTO
N, D
IAPH
RAG
M P
UM
P1
738
0124
SLEE
VE, D
IAPH
RAG
M P
UM
P PU
SHBU
TTO
N1
NO
TE: P
ARTS
2 A
ND
3 M
UST
BE
PUR
CH
ASED
TO
GET
HER
TOLE
RAN
CES
FRAC
TIO
NS:
AJB
U
MW
10/2
6/16
3/14
/00
A1
OF
1
STAN
DAR
D
6003
07
1:1
AS N
OTE
D, S
EE B
OM
PAR
T #:
(PPB
) PN
EUM
ATIC
PU
SHBU
TTO
N
SHEE
T:R
EV�:
OR
IG.:
REV
ISIO
N:
SCAL
E:R
EF�:
MAT
'L:
Indi
anap
olis
, Ind
iana
NO
TED
EXC
EPT
AS
ANG
LE:
TITL
E / D
ESC
.:
3 PL
CS:
Will
ough
by In
dust
ries
Inc.
2 PL
CS:
0�03
0�01
51/
32"
1
SIZE
:
WIL
LOU
GH
BY
DR
AWIN
G:
Push
But
ton
Det
ail
Replacement Part Numbers
Page 43Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
DR
AWIN
G:
Spra
y H
ead
Det
ail
ITEM
#PA
RT
#D
ESC
RIP
TIO
NQ
TY.
180
0001
WAS
HFO
UN
TAIN
SPR
AYH
EAD
BAS
E, 4
5, S
.S.
12
3201
57A
SPR
AY H
EAD
, 0.5
GPM
, 13/
16"-
27 T
HR
EAD
1
ABE
H
BEH
08/0
5/14
08/0
5/14
A1
OF
1
STAN
DAR
D
3201
57A-
ASM
B
3:2
PAR
T #:
SPR
AY H
EAD
ASS
Y�, 0
�5 G
PM
SHEE
T:R
EV�:
OR
IG.:
REV
ISIO
N:
SCAL
E:R
EF�:
MAT
'L:
TITL
E / D
ESC
.:W
illou
ghby
Indu
stri
es In
c.In
dian
apol
is, I
ndia
na3
PLC
S:
NO
TED
EXC
EPT
AS
TOLE
RAN
CES
2 PL
CS:
FRAC
TIO
NS:
ANG
LE:
0�03
0�01
51/
32"
1
SIZE
:
1
2
WIL
LOU
GH
BY
Replacement Part Numbers
Page 44Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
DR
AWIN
G:
Liqu
id S
oap
Dis
pens
er D
etai
lReplacement Part Numbers
Page 45Rev. 9/2021 www.willoughby-ind.com
Installation & Operation ManualAquafount® 180° WashfountainWAF-5403 Series / WAF-5404 Series
Willoughby Industries, Inc. TOLL FREE (800) 428-4065 ● LOCAL (317) 875-0830 ● FAX (317) 875-0837
WarrantyAquasurf® Solid Surface Products are a homogeneous blend of resins, mineral filler and colorant manufactured for panels, molded and/or shaped products and components. Aquasurf® Solid Surface products provide a luxurious appearance with the durability of stain proof, impact resistant, burn resistant material with ease of maintenance and cleaning.
Willoughby Industries, Inc. warrants to commercial and institutional purchasers only that each unit will be free from defects in workmanship and materials under normal use and service upon the following terms and conditions. The period during which Aquasurf® components are warranted as follows:
1. Aquasurf® solid surface components are warranted for 2 years from date of shipment.
2. All other components warranted for 1 year from date of shipment.
This warranty does not cover installation or any other labor charges and does not apply to any components damaged by accident, abuse, improper installation or improper maintenance. This warranty does not cover any installation that did not comply with national, state and local building, plumbing or electrical codes. The warranty is limited to replacing or repairing at Willoughbys option, transportation charges prepaid by the purchaser, any Aquasurf® component or part which upon our inspection shall be deemed as defective within the limitations of this warranty. The replacement or repair of defective units as stated in this warranty shall constitute the sole remedy of the purchaser and the sole liability of Willoughby Industries, Inc. Willoughby Industries, Inc. shall not otherwise be liable under any indirect damages caused by defects in the repair or replacement thereof.
This warranty only extends to commercial and institutional purchasers and does not extend to any others, including consumer customers of commercial institutional purchasers. This warranty is in lieu of all other warranties, expressed or implied, including implied warranty of merchantability or fitness or a particular purpose or otherwise.
Warranty