Installation Guide - 伊藤忠テクノソリューションズacad/pdf/v19/install_E.pdf2.1...

Advance CAD

Installation Guide

Advance CAD software version 19

Installation Guide

Advance CAD software version 19

1st Edition: September 9, 20092nd Edition: December 1, 2009 (V19.01)

Copyright © 1986-2009 ITOCHU Techno-Solutions CorporationART Village Osaki Central Tower, 2-2, Osaki 1-chome, Shinagawa-ku, Tokyo 141-8522, Japan

No part of this document may be reproduced, in whole or in part, by any means without permission.The content of this document is subject to change without notice.This document is based on the premise that the content will change according to future develop-ment. Although it is written to be accurate as much as possible, ITOCHU Techno-Solutions Corpora-tion will neither be responsible for any damages caused by the document, nor for any damages from changes caused by future development.

Sun, Sun Microsystems, Sun Workstation, Solaris, SunOS, OpenWindows, NFS, IPC, and IPX are trademarks or registered trademarks of Oracle and/or its affiliates in the United States and other countries.SPARC is a trademark of SPARC International, Inc. in the United States and other countries.UNIX is a registered trademark in the United States and other countries, licensed exclusively through X/Open Company Ltd.MS, MS-DOS, Windows, Windows NT, Windows 2000, Windows XP, Visual C++, and Microsoft are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.SolidWorks and the SolidWorks logo are registered trademarks of SolidWorks Corporation.Copyright information of FLEXnet Publisher and FLEXlm is as follows.Copyright (c) 2008 Acresso Software Inc. and/or InstallShield Co.Inc. All Rights Reserved.Copyright information of libtiff is as follows.Copyright (c) 1988-1996 Sam LefflerCopyright (c) 1991-1996 Silicon Graphics, Inc.Other company and product names are trademarks or registered trademarks of their respective owners.

Introduction

This document describes installation procedures of the Advance CAD software version 19. The procedures are different for each Advance CAD platform. Please refer to required chapters.

Chapter 1 About platforms

Chapter 2 Installation for Windows

Chapter 3 Appendix A

Technical contacts

For technical questions about Advance CAD, please contact the following.Questions are limited to customers with Advance CAD Software Maintenance Contract.

------------------- Advance CAD hotline service -------------------------------------------------------Phone : 03-5434-0095Fax : 03-5434-0054E-mail : [email protected]

-------------------------------------------------------------- Office hours: Weekdays 9:00 - 17:30 ---

Contents

Chapter 1About platforms .................................................................... 11.1 List of supported platforms........................................................................... 1

Chapter 2Installation for Windows........................................................ 32.1 Preparation for installation .......................................................................... 4

2.1.1 Hardware requirements ................................................................................................. 42.1.2 Software requirements................................................................................................... 42.1.3 Obtaining the released software ................................................................................... 42.1.4 License application ........................................................................................................ 52.1.5 Obtain documents.......................................................................................................... 52.1.6 Fill in the installation check list....................................................................................... 62.1.7 User registration ............................................................................................................ 8

2.2 New installation........................................................................................... 92.2.1 Install Advance CAD.................................................................................................... 102.2.2 Configure license server and check startup................................................................. 152.2.3 Set plotter environment................................................................................................ 15

2.3 Version upgrade........................................................................................ 162.3.1 Back up user data........................................................................................................ 162.3.2 Uninstall existing Advance CAD .................................................................................. 182.3.3 Install Advance CAD.................................................................................................... 182.3.4 Restore user data ........................................................................................................ 182.3.5 Configure license server and check startup................................................................. 202.3.6 Set plotter environment................................................................................................ 20

2.4 Configure the license server ...................................................................... 212.4.1 Install FLEXlm.............................................................................................................. 212.4.2 Install the license file.................................................................................................... 242.4.3 Configure and start the license server ......................................................................... 24

2.5 Configure client machines.......................................................................... 272.5.1 Set environment variable LM_LICENSE_FILE ............................................................ 272.5.2 Check startup of Advance CAD ................................................................................... 27

2.6 Other settings............................................................................................. 292.6.1 File attribute settings and operation............................................................................. 292.6.2 Configure and check operation of printer/plotter.......................................................... 29

2.7 Add Advance CAD ..................................................................................... 312.7.1 Add the Advance CAD package .................................................................................. 31

2.8 Uninstall ..................................................................................................... 332.8.1 Uninstall the license server program ........................................................................... 332.8.2 Uninstall Advance CAD ............................................................................................... 34

2.9 Advance CAD installation checklist............................................................ 37

AppendixAFloating license................................................................. 41A.1Overview ..................................................................................................... 41A.2Simultaneous access license count for Advance CAD ............................... 42A.3How to select a license server .................................................................... 43A.4Issue and change licenses ......................................................................... 45A.5License file .................................................................................................. 47

A.5.1License file details ........................................................................................................ 48A.5.2FLEXnet Publisher TCP/IP port number ...................................................................... 49A.5.3Merge license files ........................................................................................................ 49

Contents

A.6Notes on FLEXnet Publisher (formerly FLEXlm) ........................................ 51A.6.1Search order of license paths ....................................................................................... 51A.6.2Notes on obtaining display names (Windows only) ...................................................... 51

A.7 License management tool ......................................................................... 52A.7.1Stop the license server ................................................................................................. 52A.7.2ID lookup of the license server ..................................................................................... 52A.7.3Re-read the license file ................................................................................................. 52A.7.4Monitor the license status ............................................................................................. 53A.7.5Set license environment variables ................................................................................ 53A.7.6Check license version .................................................................................................. 54A.7.7Borrow a license ........................................................................................................... 54

A.7.7.1Borrow a license ................................................................................................... 55A.7.7.2Check status of a borrowed license ..................................................................... 56A.7.7.3Return a borrowed license before expiration ........................................................ 56

A.8License management tool (Windows only) ................................................. 58A.8.1Stop the license server ................................................................................................. 58A.8.2Re-read the license file ................................................................................................. 58A.8.3Monitor the license status ............................................................................................. 59A.8.4Check license version .................................................................................................. 59A.8.5Configure the license environment variable ................................................................. 59A.8.6Borrow a license ........................................................................................................... 60

A.8.6.1Borrow .................................................................................................................. 60A.8.6.2Return ................................................................................................................... 61

A.9About the Windows firewall ........................................................................ 62A.9.1Method 1: Register the FLEXnet Publisher module as an exception ........................... 62A.9.2Method 2: Register the ports used by FLEXnet Publisher as exceptions .................... 65

A.10License manager: Frequently asked questions ........................................ 68A.11License management utility operation example ....................................... 70


1.1 List of supported platformsThe system requirements for Advance CAD are explained for each platform. Please refer to specifications for the applicable platform.

Windows version (Microsoft Corporation)

• Operating systemWindows XP Professional Service Pack 2 and above

• Supported computersAn IBM PC compatible computer with Pentium or compatible CPU, running the Japa-nese version of the above operating system. (Itanium computers are not supported.)

• Memory256 MB or more is recommended.

• VRAM2 MB or more

• PeripheralsNetwork card (Ethernet board)

• Compiler (only when using the programming interface)Visual C++ 2008 Japanese version or later

• Screen colors16 bit colors, 32 bit colors (True Color)

• Screen resolution (desktop area)1024 x 768 pixels or more

• Advance CAD is a 32-bit applicationIt operates on a 64-bit OS in the compatibility mode, but be sure to conduct a thorough verification before use.

Installation Guide (Advance CAD Version 19) 1


2 Installation Guide (Advance CAD Version 19)


This chapter explains the installation procedure of Advance CAD for Windows.



2.1 Preparation for installation

2.1.1 Hardware requirements

Disk space

Approximately 150 MB disk space is required for a full installation of Advance CAD for Windows. Please check the capacity of the installation drive.

Page file size

To ensure comfortable operation of Advance CAD, a page file of sufficient size is required. The page file size is defined when Windows is installed, but it can be changed later.To launch a single instance of Advance CAD and plot output at the same time, the minimum requirement of the page file is as follows.

Initial page file size : 80 MBMaximum page file size : 128 MB

* The above values are based on experience. They are not results of logical calculation.

2.1.2 Software requirements

To install Advance CAD for Windows, the following software must be installed on the system in advance.

• Windows XP Professional Service Pack 2 or later

To use a printer or plotter, an applicable driver must be installed as well.

The following software is required to use the programming interface.

• Visual C++ 2008

Visual C++ 2008 is not included with Windows XP Professional, and must be separately purchased.

2.1.3 Obtaining the released software

Download Advance CAD for Windows software from the following web site. The file to be downloaded is a self-extracting setup program.

Download

http://www.ctc-g.co.jp/~acad/dmenu.html

In the Windows version, the license manager (FLEXlm) is provided separately from Advance CAD.To a computer for which the license server should be set up, download the FLEXlm software as well.



2.1.4 License application

A license is required to use Advance CAD. To apply for a license, the host name and host ID of the license server computer is required. Perform the following procedure to look up your host name and host ID to apply.

Host nameThe Advance CAD system uses your "computer name" as the host name.

From the [Start] menu, select [Settings] > [Control Panel] > [System].In the displayed window, select the [Network ID] tab.In the top center of the window, the full computer name is displayed. This is the host name

Host IDAlternatively, you can launch [Start] > [Program] > [Accessories] > [Command Prompt], and execute the ipconfig command to look up the value.Execute the ipconfig /all command to refer to the number shown in [Physical Address].

2.1.5 Obtain documents

Advance CAD documents are provided in PDF format.Please obtain the documents from the site that you downloaded the software.



2.1.6 Fill in the installation check list

Look up information for filling in the check list as follows.

(1) Physical memory/virtual memoryFrom the [Start] menu, select [Settings] > [Control Panel] > [Administrative Tools] > [Computer Management], then navigate to [System Information] > [System Information] > [System Summary].

Write down the amount of [Total Physical Memory] to [Memory].Write down the amount of [Total Virtual Memory] to [Virtual memory].

(2) Ethernet addressAlternatively, you can launch [Start] > [Program] > [Accessories] > [Command Prompt], and execute the ipconfig command to look up the value.Execute the ipconfig /all command to refer to the number shown in [Physical Address]

(3) Host name and domain/workgroup nameFrom the [Start] menu, select [Settings] > [Control Panel] > [System].In the displayed window, select the [Network ID] tab.In the top center of the window, the full computer name is displayed.

Write down the value of [Full Computer Name] to [Host Name].Write down the value of [Domain] or [Workgroup] to [Domain/workgroup name].Either [Domain] or [Workgroup] is displayed.



(4) IP addressFrom the [Start] menu, select [Settings] > [Control Panel] > [Network and Dial-up Connections] > [Local Area Network] properties, and open [Internet Protocol (TCP/IP)] properties.

Write down the value of [IP Address] to [IP address].

(5) Compiler versionStart MS - Visual Studio, and refer to [Help] > [About].* Write down this information only when you plan customization via the program interface.

(6) Check user and group nameFrom the [Start] menu, select [Settings] > [Administrative Tools (Common)] > [User Manager] to check the settings.

(7) Check printer/plotter environmentWrite down the name(s) of plotter and/or printer to use.

From the [Start] menu, select [Settings] > [Printer]. Select the folder of the printer to check, and open its properties. Select the [Port] tab to check the values.

When performing version upgrade, check the content of oplot.bat found under the exe directory.

In the above example: Plotter name : plot1 (Refer to a value after [set QUE = ]).Formatter : ap_HPGLParameter : HP-DJET-RTL (Refer to a value shown after [set PRM = ]).

set PRM=HP-DJET-RTL set QUE=plot1

ap_HPGL -p%PAS% -i%PRM% %SCR% -j%QUE%

Formatter Parameter file



When a Windows printer is configuredFrom the [Start] menu, select [Settings] > [Printer]. Launch a configured printer and open [Print] > [Properties].Write down the driver name that appears on the [General] tab.To check the detailed settings of a port, click the [Configure Port] button, then select a port that launches and uses a serial port. Click the [Settings] button.From the settings of the port that is used, write down using port properties.For details, please refer to "Plotter Guide."

(8) Advance CAD packageSelect the package necessary for you, and mark it to confirm.

2.1.7 User registration

Here, register a user, who is used for installing Advance CAD, in the Windows system.If the user is already registered, a new user is not needed.The user must belong to the [Administrators] group.This user is also used to confirm that Advance CAD is installed correctly. Perform the following steps to regis-ter.

• From the [Start] menu, select [Settings] > [Control Panel] > [Administrative Tools] > [Computer Management]. To add a user or a group, select [System Tools] > [Local Users and Groups] > [Users] or [Groups]. From the list of specified groups, select [Administrators].

If a home directory is not created automatically, create it manually.


2.2 New installation

2.2 New installationPerform the following steps.

(1) Fill in the installation check listFill required information in the check list found at "2.9 Advance CAD installation checklist."See "2.1.6 Fill in the installation check list."

(2) Register user account Register a user who installs Advance CAD.See "2.1.7 User registration."

(3) Install softwareThis document assumes that the software is installed in the C:\acad directory.

(4) Configure license server and check startupUse the network floating license management program FLEXlm to start up the license server. Perform this step only for the server computer which should run the license server.If the license server is not running, Advance CAD will not start up. Install FLEXlm to the server machine and configure it. Then, check whether you can start up Advance CAD. For details, see "4. License server settings."



2.2.1 Install Advance CAD

Installation of Advance CAD consists of copying Advance CAD system files and registering the Advance CAD program to the [Start] menu.

Log on to the system using the user account used for installing Advance CAD.

(1) Put the downloaded self-extract file to a temporary location, and double-click the file to start SETUP.

(2) If the user who is performing the installation does not have Administrators rights, the following message is displayed.

* If you continue the installation, registration to the [Start] menu is performed only for the user who is installing the software.



(3) In [Choose Destination Location], select the destination folder.

(4) In [Setup Type], select an installation method for Advance CAD.

Select [Standard], [Compact], or [Custom] installation method. When using optional software, or when installing the license server only, select [Custom].

Packages installed when [Standard] is selected• Advance CAD basic module• Plotter (partially)

Packages installed when [Compact] is selected• Advance CAD basic module

Packages installed when [Custom] is selected (default)• Advance CAD (full installation)• CADAM option• DXF option• NC option• P&ID option• Sequence diagram option• ACADWorks option



• Outline font option• Plotter (full installation)• Programming interface

When [Custom] is selected, you can select items from the component list box.

(9) Select a folder in [Select Program Folder] (The default is "Advance CAD").



(10) When selection is complete, files are copied.

(11) If you have selected one or more programming interfaces, after the file copy operation has completed, a prompt is displayed to select whether or not to configure the user environment variable PATH. If you select the check box, the setting is done automatically. If you do not select, PATH is not set. To start Advance CAD from the DOS prompt, select this box, or configure the environment variable PATH after the setup. For details on environment variables, see "3.2 Configure and check operation of Advance CAD."



(12) When installing the Advance CAD main program, a prompt is displayed to select whether or not to cre-ate an Advance CAD shortcut to the desktop.

(13) When file copy and other operations are completed successfully, the finish screen is displayed. Click the [Finish] button to finish. When the Advance CAD basic software is selected for installation, [acad] is registered to the [Start] menu. An [Advance CAD] shortcut is created on the desktop. Also, UnInstallShield is registered as [Advance CAD Version 19] in [Control Panel] > [Add/Remove Programs].

When you finish with the [Configure Advance CAD setting file (ACAD.SET)] check box turned on, the ACAD.SET file is copied from sample\ENV to your uenv directory with the paths updated to your installation environment, and opened with Notepad. If ACAD.SET already exists, turn off the check box.

When you finish with the [Configure LM_LICENSE_FILE environment variable] check box turned on, the environment variable LM_LICENSE_FILE is configured. If LM_LICENSE_FILE is already con-figured, turn off the check box.



2.2.2 Configure license server and check startup

To use Advance CAD, you need to run the network floating license management program FLEXlm on the license server.See "2.4 Configure the license server."

2.2.3 Set plotter environment

Perform settings according to chapters in "Plotter Guide."



2.3 Version upgradeThis section describes the procedure to upgrade from Advance CAD Version 18.

Perform the following steps.

(1) Fill in the installation check listFill required information in the check list found at "2.9 Advance CAD installation checklist." See "2.1.6 Fill in the installation check list."

(2) Back up user dataBack up model files, symbol files, and other files under the files directory.This is required to restore the files directory after the version upgrade.

(3) Uninstall existing Advance CADUninstall the existing Advance CAD software.

(4) Install Advance CADInstall the Advance CAD Version 19 software.

(5) Restore user dataRestore backed-up model data, files customized in the old version, and other files.

(6) Configure license server and check startupUse the network floating license management program FLEXlm to start up the license server. Perform this step only for the server computer which should run the license server.If the license server is not running, Advance CAD will not start up. Install FLEXlm to the server machine and configure it. Then, check whether you can start up Advance CAD. See "2.4 Configure the license server" for details.

(7) Set plotter environmentPerform settings according to "Plotter Guide."

2.3.1 Back up user data

Back up model files created by user, files customized by user, and other files.

**************************************************************************************

Be sure to perform backup before version upgrade.

**************************************************************************************

When the Windows system has a backup device (such as 4 m DAT device)

From the [Start] menu, use [Accessories] > [System Tools] > [Backup] to take a backup.


2.3 Version upgrade

When a Windows system with a backup device exists on a same network, even if the current system does not have a backup device, you can take a backup on the backup device of another system via the network. In this case, perform the following steps.

• Use [Explorer] to set files in the current system accessible from the network.• From a system with a backup device, use [Explorer] to make files accessible by assigning the

file system to a network drive. From the [Start] menu, select [Accessories] > [System Tools] > [Backup] to take a backup.

List of Advance CAD environment files

Function Initial directory File name

Environment settings

C:\ACAD\UENV *.SET

Plot C:\ACAD\uenv *.PRM

C:\ACAD\exe oplot.bat

qplot.bat

hcopy.bat

aprint.bat

Drawing frame C:\ACAD\draw All

Create text C:\ACAD\font All

Macro C:\ACAD\macro All

Register constant C:\ACAD\maint All

Data transfer

Associate

Define color

Create mark

Create menu C:\ACAD\menu USER*.MEN

Create message C:\ACAD\msg MSG90.TXT ERR90.TXT



2.3.2 Uninstall existing Advance CAD

To install Advance CAD on a computer with Advance CAD already installed, you must uninstall the existing Advance CAD first before installation.Be sure to perform backup before uninstallation.

Perform the following steps to uninstall the software.(1) Uninstall the license server(2) Uninstall Advance CAD

For details, see "2.8 Uninstall."

2.3.3 Install Advance CAD

Install the Advance CAD software.For details, see "2.2.1 Install Advance CAD."

2.3.4 Restore user data

Restore the model files created by user, environment setting files, and other files, and copy usable files as appropriate.

Select [Start] > [Program] > [Accessories] > [System Tools] > [Backup], and restore data to a temporary direc-tory such as C:\acadtmp.

See the following table to modify the data.

Meanings of symbols in the table in the reference pageModification : No modification is necessaryE : Use an editor to modify- : Others

Parts C:\ACAD\parts All

Spec data C:\ACAD\spec All

Search model C:\ACAD\work ACADMDM.SET

AACDLOCALMDM.SET

Accounting Any ACADUAF*

List of Advance CAD environment files

Function Initial directory File name


2.3 Version upgrade

Environment setting fileModification

Required? Remarks

exe/oplot.bat

exe/oplot.bat

exe/aprint.bat

exe/hcopy.bat

uenv/*.PRM

uenv/*.SET

draw

font

macro

maint

menu/USER*.MEN E Modify deletion and modification commands

msg/MSG90.TXT ERR90.TXT

parts

slo

spec

work/ACADMDM.SET

work/ACADLOCALMDM.SET

work/*.MGN

work/*.MLS

work/*.MDM

work/*.LMG

ACADUAF.ASC

User dataModification

Required? Remarks

Model

Symbol

APX

APG E Use apgconv.exe to convert to .APX



(3) Set printer/plotter environmentBasically, Advance CAD Version 18 parameter files can be used. This is normally restored to the uenv directory. For details, see "Release Notes" and "Plotter Guide."

2.3.5 Configure license server and check startup

To use Advance CAD, you need to run the network floating license management program from Macrovision Corporation, FLEXnet Publisher, on the license server.See "2.4 Configure the license server."

2.3.6 Set plotter environment

Perform settings according to "Plotter Guide."


2.4 Configure the license server

2.4 Configure the license serverThis chapter describes the floating license of FLEXlm, the network floating license management program adopted by Advance CAD, along with the operation check procedures for Advance CAD.

FLEXlm requires a server and a client. A server which runs the license server is called a server machine, and a com-puter which only runs Advance CAD is called a client machine.A single computer can be a license server and a client machine at the same time. At least one license server machine is required on the network to issue license to client machines. Configuration of a license server is a bit complicated, but configuration of a client machine is simple.

Perform the following steps to configure the license server.

Caution.The user who installs FLEXlm must belong to the [Administrators] group.

2.4.1 Install FLEXlm

FLEXlm is software used to start, stop, and manage the license server. A safe installation is to place the license management software in the local disk of the server machine. It is not needed for client machines which do not start the license server.Perform the following steps.

(1) Obtain the FLEXlm software. Download the FLEXlm software from our web site.

Downloading site

http://www.ctc-g.co.jp/~acad/dmenu.html

The floating license system uses TCP/IP. Therefore, IP addresses and host names must be able to resolve to one another. Before performing the following settings, configure related settings properly, such as %SystemRoot%\system32\drivers\etc\hosts.

[Caution]

(1) Log on to the system.(2) Install FLEXlm.(3) Install the license file.(4) Configure and launch the license server.(5) Check startup of Advance CAD.



(2) Double-click the downloaded file to start the setup.

(3) In [Choose Destination Location], select the destination folder.

(4) Select a folder in [Select Program Folder] (The default is "FLEXlm for Advance CAD").



(5) When selection is complete, files are copied.

(6) When file copy and other operations are completed successfully, the finish screen is displayed. Click the [Finish] button to finish.

* When using multiple servers, install to all server machines using the same procedure.



2.4.2 Install the license file

A license file is provided via email or fax. Create a file named license.dat under the C:\FLEXlm\files directory using a text editor such as Notepad, with the following taken into account.

• Host name in the SERVER line In the line beginning with the text SERVER, change "HostName1" to your host name.

• Absolute path in the DAEMON line At the end of the line beginning with the text DAEMON, specify the absolute path where the vendor daemon (CTCMDARD) resides. This usually resides in the EXE directory. In this case, specify C:\FLEXlm\EXE\CTCMDARD.

2.4.3 Configure and start the license server

To start Advance CAD, FLEXlm must be running. The following section describes the configuration and startup procedures of the license server. This task must be done by a user who has Administra-tors rights.

License management software

The license management software consists of the following files.(C:\FLEXlm is assumed as the installation directory. )

C:\FLEXlm\exelmgrd.exe : License daemonCTCMDARD : Vendor daemonlmutil.exe : License management toollmtools.exe : License management tool with GUI

C:\FLEXlm\sampleoptions.dat : Option file for the vendor daemon

SERVER HostName1 008012345678 TCP:7282DAEMON CTCMDARD C:\FLEXlm\EXE\CTCMDARDFEATURE advancecad_win.base CTCMDARD ..............................................FEATURE advancecad_win.font CTCMDARD ................................................

SERVER myhost 008012345678 TCP:7282DAEMON CTCMDARD C:\FLEXlm\EXE\CTCMDARDFEATURE advancecad_win.base CTCMDARD ..............................................FEATURE advancecad_win.font CTCMDARD ................................................



Configure the license server

• From the [Start] menu, select and start [FLEXlm for Advance CAD] folder > [lmtools].

• Select the [Config Services] tab, and configure [Service Name], [Path to the lmgrd.exe file], [Path to the license file], and [Path to the debug log file]. To register the settings to a service (auto-start settings) mark the [Use Services] and [Start Server at Power Up]boxes, and click the [Save Service] button.

[Service Name] : Enter the FLEXlm service name (for example, "FLEXlm for Advance CAD").

[Path to the lmgrd.exe file] : Specify lmgrd.exe in the exe directory under the FLEXlm installation directory.

[Path to the license file] : Specify the file created in "2.4.2 Install the license file."[Path to the debug log file] : Specify a file to log the running statuses of the license manager. This

file helps troubleshooting.

* Click the [Browse] button to start the file dialog that can be used to specify the desired file.

[Use Services] check box : Mark the check box to register FLEXlm as a service.

[Start Server at Power Up] check box : Mark the check box to start the FLEXlm service auto-matically at power-up.



[Save Service] button : Click to register FLEXlm as a service. (*[Use Services] must be marked.)

[Remove Service] button : Click to delete the FLEXlm service installed as a ser-vice.

Start the license server

• Click the [Start/Stop/Reread] tab. Select the registered service name and click the [Start Server] button.

[Start Server] : Start the license manager.[Stop Server] : Stop the license manager.[ReRead License File] : Re-read the license file.


2.5 Configure client machines

2.5 Configure client machines

2.5.1 Set environment variable LM_LICENSE_FILE

Environment variable LM_LICENSE_FILE is required to start Advance CAD.Set the PortID@ server name to this environment variable.From the [Start] menu, select [Settings] > [Control Panel] > [System]. Select the [Advanced] tab, click the [Environment Variables] button, and define LM_LICENSE_FILE as a user environment variable.A client machine must be able to communicate with the license server machine via TCP/IP.

% set LM_LICENSE_FILE=portid@server

Example set LM_LICENSE_FILE=7282@ctc

When other software that adopts FLEXlm is running, and a license server is started for each license file issued by the corresponding vendor, list multiple license file names separated by semicolons.

> set LM_LICENSE_FILE=PortID1@server1;PortID2@server2;PortID3@server3

Even for redundant servers, a corresponding number of entries separated by semicolons;is required (three in the above case).Use the same PortID for the three servers.

> set LM_LICENSE_FILE=PortID@server1;PortID@server2;PortID@server3

Note) From Version 13 or later, client machines will no longer need "NWLink IPX/SPX-compatible transport." �However, this change caused a change in the method to obtain DISPLAY names, compared to Version 12 or older. As a result, two licenses are necessary to start Advance CAD Version 13 (or later) and Version 12 (or older) on the same screen.

2.5.2 Check startup of Advance CAD

Log on using an account of a general user who uses Advance CAD. Check startup of Advance CAD.

(1) Configure Advance CAD To operate Advance CAD, environment variables must be modified and some files must be edited.

PortID@ server namePortID : The number at the end of the SERVER row in the license file.

In Advance CAD, 7282 is set by default.Server name : License server computer name



• Define user environment variables (PATH, ACAD_SET, and LM_LICENSE_FILE) as follows.

Modify environment variables in [Start] menu > [Settings] > [Control Panel] > [System].

• Edit the fileCopy ACAD.SET under the sample\ENV directory of Advance CAD, and edit directories listed in the file to match your environment. For example, perform the following.

Example C:\> COPY C:\ACAD\sample\ENV\ACAD.SET C:\ACAD\ACAD.SET

(2) Check operation of Advance CADCheck startup of Advance CAD. The following methods are possible to start Advance CAD.

• Start from the [Start] menuWhen Advance CAD is installed, it is registered to the [Start] menu. Select the registered Advance CAD icon to start Advance CAD. Check the operation.

• Start from the desktop shortcutWhen Advance CAD is installed, an Advance CAD shortcut icon is registered on the desktop. Select the registered Advance CAD icon to start Advance CAD. Check the operation.

• Start from the command promptIn the command prompt, enter the following command.

Example C:\ACAD\work> C:\ACAD\exe\acad.exeAdvance CAD starts. Check its operation.

Environment variable Value

PATH Add the EXE directory of Advance CAD to the value of user environ-ment variable PATH. For example, add C:\ACAD\EXE. Any user who starts Advance CAD from the DOS prompt must perform this setting.

ACAD_SET The directory in which ACAD.SET resides. For example: C:\ACAD\UENV\

LM_LICENSE_FILE See "2.5.1 Set environment variable LM_LICENSE_FILE."

File name Copy destination

ACAD.SET For example, to C\ACAD\UENV


2.6 Other settings

2.6 Other settings

2.6.1 File attribute settings and operation

From Advance CAD Version 12 or later, .MDL files will be associated to Advance CAD as Advance CAD model files.You can double-click a model file from [Explorer], etc. to start Advance CAD.Please note the following:

• When environment variable [ACAD_SET] is not definedWhen ACAD_SET is not defined, the ACAD.SET file must reside in the start directory (the directory where the double-clicked model file resides). Either configure environment variable "ACAD_SET", or specify startup option "-p" in the association set-ting (see "System Administrator Guide" for details).

• Session file outputWhen ACAD.SET does not have a #LOG# item specified (by default, it is not specified), a session file (ACAD-20001006-130034-00275.LOG) is created in the start directory (the directory where the double-clicked model file resides). Specify the output directory in the #LOG# item. (See "System Administrator Guide" for details.)

• Commands to create work files in the start directory Advance CAD supports several commands to create work files in the start directory (the directory where the double-clicked model file resides). For details on the commands, see "Utility Guide", "System Administrator Guide", etc. In association settings, specify the Advance CAD startup option "-w" (see "System Administrator Guide" for details). When started from the [Start] menu or the shortcut, the default start directory is the work directory.

To change association, from [Explorer], navigate to [Tools] > [Folder Options] > [File Types], and select MDL files in [Registered File Types]. If MDL is not listed, add it.In [Advanced] of [Details for 'MDL' extension], set the "open" action.Then, in [Edit actions for type], edit [Application used to perform action].Example) "C:\ACAD\exe\acad.exe" "%1" "-wC:\ACAD\work"

2.6.2 Configure and check operation of printer/plotter

To use a printer or plotter in Advance CAD, you must configure the printer in the Windows system. This is done using [Print Manager]. For details on the printer setting procedure on the Windows system, see online help. For an output using the Windows printer driver, the following settings are not required.Printer/plotter configuration in Advance CAD for Windows is basically the same as Advance CAD for UNIX system. Perform the following steps.

Copy scripts to perform printer/plotter outputEdit scriptsCopy parameter filesCheck output



(1) Copy scripts to perform printer/plotter outputThe sample\PLOT directory of Advance CAD contains scripts that perform print/plot. Copy the applica-ble script to the EXE directory. Copy the following files.

aplot.bat : Offline output (*)hcopy.bat : Hard copy outputoplot.bat : Online outputqplot.bat : Quick output

(2) Modify the scriptThe script must be edited according to your environment. The items to be edited for each environment are defined in the beginning of the script. They are as follows.

Output examples issued from Windows to a printer/plotter on a UNIX system are also included. To out-put to a UNIX printer/plotter, the following variables must be additionally defined.

(1) Copy parameter filesParameter files corresponding to the configured printer/plotter must be copied from the sample\PLOT directory to the uenv directory. For details on which files to copy, see "Advance CAD Plotter Guide."

(2) Check outputTo check output from a printer or plotter, perform the following.

• Output the file created in Windows to a printer defined in Windows. For example, start the main Windows help and print out any file. Check that the data is output correctly.

• Request drawing output from Advance CAD.

Variable name Definition

PRM Parameter file name

QUE Printer name (printer name defined in the Windows NT system)

QPR Parameter file name for HCOPY or QPLOT

Variable name Definition

HOST UNIX host name to which the printer/plotter is connected

RQUE Cue name on the UNIX system

To output to a UNIX printer/plotter, Windows and UNIX computers must be able to communicate via TCP/IP. In addition, output process uses rsh. Therefore, the r series commands in TCP/IP must be made available.

[Caution]


2.7 Add Advance CAD

2.7 Add Advance CAD

2.7.1 Add the Advance CAD package

Log on to the system using the user account used for installing Advance CAD. From the [Start] menu, select [Settings] > [Control Panel] > [Add/Remove Programs] (For Windows XP, it is in the [Start] menu > [Control Panel] > [Add/Remove Programs] ).

Select [Advance CAD Version 19] from the list, and click the [Change] button.

From [Modify], [Repair], [Remove], select [Modify] and click the [Next] button.



In the component selection window, mark the check box for the package(s) to add and click the [Next] button to copy the files.

When complete, click the [Finish] button to finish.


2.8 Uninstall

2.8 UninstallPerform the following steps to uninstall Advance CAD.

• Uninstall the license serverThis procedure is necessary only in the system for which the license file is configured. See "2.8.1 Uninstall the license server program" for instructions.

• Uninstall the Advance CAD system See "2.8.2 Uninstall Advance CAD" for instructions.

2.8.1 Uninstall the license server program

For a system which has the license server configured, the license server program must be uninstalled before uninstallation of the Advance CAD system.This task must be done by a user who has Administrators rights, such as Administrator.Perform the following steps.

(1) Confirm that other computers are not communicating with the license server program (in short, stop all Advance CAD programs).

* The license management utility can be used to check the number of licenses in use. For details, see "A.8 License management tool (Windows only)."

(2) Log on to the system using the user account which has Administrators rights.

(3) In the [Start] menu, select [FLEXlm for Advance CAD] > [lmtools]. Select the [Start/Stop/Reread] tab, click the [Stop Server] button, and stop the license server program.

(4) In the lmtools window, select the [Config Services]tab. If the [Use Services] check box is selected, click the [Remove Service] button and delete it from the service.



(5) From the [Start] menu, select [Control Panel] > [Add/Remove Programs]. Select [FLEXlm for Advance CAD] from the list, and click the [Add/Remove] button. In the deletion confirmation prompt, select the [YES] button.

Now the license server program is uninstalled.

This task is not necessary when uninstalling Advance CAD systems from client machines.

2.8.2 Uninstall Advance CAD

Log on to the system using the user account used for installing Advance CAD. From the [Start] menu, select [Settings] > [Control Panel] > [Add/Remove Programs].

Caution. When uninstalling Advance CAD Version 12 or older, the environment variable PATH will be deleted. If you use PATH in other applications, back up PATH first. See "l How to back up the environment variable PATH."


2.8 Uninstall

Select [Advance CAD Version 19] and click the [Delete] button.

From [Change], [Modify], and [Remove], select [Remove] and click the [Next] button.

In the deletion confirmation prompt, select the [OK] button.



Uninstallation starts. When complete, click the [Finish] button to finish.

Caution. In Advance CAD Version 12 or later, the environment variable PATH configured in SETUP, the ACAD.SET file, the .EDITRC file, and the Acadhelp.ini file are not deleted. To clean up the PATH environment variable, select the [Start] menu > [Settings] > [Control Panel], then edit and delete declarations related to Advance CAD from the user environment variable PATH. Delete the ACAD.SET file from the uenv directory. Delete the .EDITRC file from the installation directory. Delete the Accadhelp.ini file from %SystemRoot%\syetm32.

How to back up the environment variable PATH

When uninstalling Advance CAD Version 12 or older, the environment variable PATH will be deleted. Therefore, users who use the environment variable PATH in other applications must take a backup using the fol-lowing procedure.

From the [Start] menu, select [Settings] > [Control Panel] > [System] and then select the [Environment] tab.Select (single-click) PATH in the list of user environment variables. Change "PATH" in the variable field to "PATH2" or a similar value, and click the [Set] button. When "PATH2" is registered, click the [OK] button to finish. Now the backup is complete. Uninstall the Advance CAD system. After the uninstallation of Advance CAD is complete, select [System] > [Environment], select "PATH2" and revert it to "PATH."


2.9 Advance CAD installation checklist

2.9 Advance CAD installation checklistFilled-in date: Year: Month: Date:

Memory MB Virtual memory MB

Host name Domain name/ workgroup name

IP address . . .

Ethernet address - - - - -

OS version Windows Service pack

C++ compiler

User name Group name

Installation destination

Home directory

System disk partitioning

C: D: E: F: G: H: I:

Printer/plotterPrinter name Formatter Parameter file



Package name

Installation selection

Standard

Minimum

Advance CAD Advance CAD basic package

Sample files

Parts utilities

Spec data utilities

DXF & DWG data transfer option

CADAM data transfer option

NC option

Sequence diagram option

P&ID option

Outline font option

ACADWork option

Advance CAD drawing output Drawing output basic module

HPGL

PS

CANON

CALCOMP

RICOH

TOYO

DSCAN

ART2

Programming interface


2.9 Advance CAD installation checklist
Sample filled-in checklist
Filled-in date: Year: Month: Day:

Memory 128 MB Virtual memory 512 MB

Host name ACAD Domain name/ workgroup name

CTC

IP address 192 . 168 . 200 . 1

Ethernet address 00 - 00 - 00 - 00 - 00 - 00

OS version Windows XP Service pack 2

C++ compiler

User name acad Group name administrators

Installation destination

Home directory D:\acad

System disk partitioning

C: 4GB D: 6GB E: CD-ROM F: G: H: I:

Printer/plotterPrinter name Formatter Parameter file

HPGL ap_HPGL HPGL.PRM


Appendix A Floating license

A.1 Overview

Floating license

Up to Version 8, Advance CAD used node-locked licenses, in which the actual workstations that can run Advance CAD had to be specified in advance. From Version 9, Advance CAD employs floating licenses, which limits the number of simultaneously running Advance CAD instances.

A floating license does not limit the workstation which can run Advance CAD. Therefore you can run Advance CAD from any workstations connected to your network. We received requests from customers to employ float-ing licenses so they can effectively utilize their licenses.The license management software used for this software is FLEXnet Publisher (formerly FLEXlm) from Macro-vision Corporation.

License server

A license server is a program which manages the number of currently running Advance CAD instances. A license server machine is a computer which runs a license server. A license server manages a single LAN (local area network) or multiple LANs connected to a network. For multiple LANs which are not connected to a single network, a separate license server must be installed for each LAN.Workstations that run Advance CAD must be able to be served from a license server via a network. Such appli-cation which is served from the license server is called a client, and a computer which run a client is called a cli-ent machine.

Since license servers and clients interact via TCP/IP sockets, workstations from different manufacturers can coexist on a same LAN. The amount of data transmitted for obtaining or releasing a license is less than 1 kilobyte per transaction. The CPU time used by a license server can be as little as few seconds per day if the number of clients is small. Unless there are hundreds of clients, the workload of a license server is small and negligible.


A.2 Simultaneous access license count for Advance CAD

Licenses are counted by the number of displays. In other words, even if multiple Advance CAD instances are started at the same time, only one license is used as long as the instances are displayed on the same screen.

In a configuration where Advance CAD is operated by remote login from another workstation such as an X termi-nal, one license is used because the data is displayed on the screen of the X terminal instead of the workstation run-ning Advance CAD.

In contrast with the previous node-locked licensing method, upgrading a workstation to a higher model does not result in paying license transfer fees or changing the license file. However, the license server machine is an excep-tion.

When the license management program has stopped, Advance CAD will not start up. In addition, currently running Advance CAD instances will not accept commands other than saving models and exiting the program. In this case, you must save the active model as required and stop Advance CAD. Wait for the license program to restart, and then restart Advance CAD.

Optional functions (seat license)

This licensing is applied to NC, P&ID, sequence diagrams, DXF/DWG interface, CADAM interface, and ACADWorks. These functions are also managed by floating licenses. Take P&ID for example. When the ini-tial P&ID command is entered, a license is obtained. When a P&ID license is not purchased, or the number of concurrently accessed licenses already exceeds the number of purchase, the function cannot be used. The P&ID license is returned when you exit Advance CAD.

Workstations that can use optional functions are also not specified. Therefore, you will not need to change your license file when the workstation that uses the option is changed. Optional function licenses are only needed for simultaneously used instances, not for the number of machines. Therefore, it is possible to buy only a limited number of licenses.

Optional functions (site license)

This licensing is applied to outline fonts and JIS part data. Only one license is needed per license server. Any number of instances of Advance CAD managed by that server can use the function.


A.3 How to select a license server

A computer or computers to be used as license server machine(s) must be specified. Once a computer is registered as a license server machine, changing the license server to another computer system is limited.For the computer to install the license server machine, take your administration framework into account and select a computer that is seldom replaced. Do not specify a computer that frequently reboots or stops as a license server.

In case a license server fails due to an accident or other reasons, licenses cannot be issued and Advance CAD cannot be started. When you restart the license server, the issue is resolved. This issue seldom occurs.To ensure safety when many licenses are served from a single server, you can employ one of the following two methods.

First, there is a way to run the same license server on three computers. This is called a redundant server configura-tion. When three servers are used, the licensing service will continue if two of the servers are running. In this way, even if the primary license server fails, another license server can respond. You can then repair and restart the failed machine. This configuration virtually eliminates server failure due to an accident. However, if two servers fail, license cannot be served.To use this configuration, three license server installation workstations must be registered. All servers use the same license file.

Another method is to split a license and run multiple independent servers. For example, if a LAN has an Advance CAD license with 100 instances, you can split the license to 30, 30, and 40 instances and assign a separate license server for each split part. With this method, when a license server fails, licenses managed by that license server can no longer be used. However, licenses managed by other running servers are still available. As such, you can avoid the situation that no license is available. In this configuration, you must use a separate license file for each server. This means that the configuration is handled as multiple sites installed on a single LAN.

As long as the number of licenses served by a single server remain small, a single license server can be safely used.


A.4 Issue and change licenses

Determine license server configuration

Determine whether to use a single server, a redundant server configuration, or a multiple independent server configuration (a LAN split to multiple sites).

For multiple LANs which are not connected to a single network, a separate license server must be installed for each LAN.When using multiple sites, you must also determine the number of Advance CAD licenses and optional func-tion licenses (such as CADAM interface) managed by each server.

Avoid a multiple independent server configuration which serves only one client or a very small number of clients. Such configuration cannot utilize the advantages of floating licensing.

Obtain a license file

Specify a host name and host ID of the server machine. The host ID is important. The host name can be changed later, but if the correct host name is known in advance, you can omit the task to change the name.

For a redundant server configuration, three host IDs are required.To use multiple sites, a license file is required for each site. Please inform us of a host ID for a server machine for each site.After your license application is reviewed, a license file will be issued.

Host names and host IDs can be looked up as follows.

Change license configuration

Since floating licensing is introduced, the following cases will not need license reissue. Therefore, no cost is necessary.

• Change in the client machine host ID due to workstation replacement• Relocation of an optional function within a site

However, the following cases will need license reissue. Therefore, additional cost will be necessary.

Operating System Host name Host ID

Sun Solaris 10 uname -n sysdef -h

Red Hat Enterprise Linux uname -n Enter ifconfig [interface], and refer to the values listed under "Link encap:Ethernet HWaddr".

Windows XP ipconfig /all Refer to the Physical Address.


(1) Change of license server machineA license file will be void when the host ID of the license server machine is changed. For a redundant server configuration, the license will be void even when part of the server machines undergoes a change in host ID. A change in license server configuration will also need license reissue.

• Switch from a single server to a redundant server configuration• Switch from a redundant server configuration to a single server• Split a single site to multiple sites• Merge multiple sites to a single site

(2) Transferring licenses between sitesWhen there are two sites and you need to transfer part of the licenses from one site to another, the license file must be reissued.This is the same for the transfer of optional function licenses.


A.5 License file

Starting from Advance CAD Version 17, a license borrowed function is added. For this reason, the license file for-mat has changed, and a license file for Version 17 or later does not support starting Advance CAD of Version 16 or older.

Starting from Advance CAD Version 18.10, Windows Vista support is added. For this reason, a license file for Ver-sion 18.10 or later does not support starting Advance CAD of Version 18.02 or older.

A license file contains the following types of lines.

• Server information lineSERVER hostname MACaddress port-no.

• Vendor daemon information lineVENDOR daemon-name daemon-dir option-name

• Feature information lineFEATURE feature-name daemon-name version date #users......

The items in each information line are separated by an arbitrary number of spaces.

The following is an example of a license file.

SERVER myserver 0123456789ab TCP:7282VENDOR CTCMDARD C:\FLEXlm\CTCMDARD.exeFEATURE advancecad_win_base CTCMDARD 19.000 permanent 1 BORROW=1344 \ ck=156 SIGN=A889C96440E4FEATURE advancecad_win_dxf CTCMDARD 19.000 permanent 1 BORROW=1344 \ ck=181 SIGN=9D0FFEE8F506

The information in a license file must not be modified, except for the following four items which your system administrator can modify. Modify them to match your server machine environment.

• Host name in the server information lineIf the host name shown in the license file is wrong, correct the name.

• Port number in the server information lineSpecify a TCP/IP port number to be used by the license server. /etc/services shows the port num-bers used by the operating system for network services. Specify an unoccupied port number of 1025 or more.

• Path name in the vendor daemon information lineSpecify a directory where the daemon program resides. If the daemon program directory is wrong, correct the directory.

• Option file name in the vendor daemon information lineAn option file is a file used by your system administrator to specify control over FLEXnet Pub-lisher lm functions such as "specify processes not to be output to a log file" or "reserve a license for a specific user." If options are not specified, do not enter a file name.


A.5.1 License file details

(1) Server information line

SERVER hostname MACaddress(hostid) port-no.hostname : Host name of a license server machine. This item can be edited.

If host names are not specified at the time of issue, the values would be "host1"..."host5". Change them to appropriate host names.

MACaddress : MAC address of a license server machine. This information must be specified at the license application of the Windows version.

hostid : Host ID of a license server machine. This information must be specified at the license application of the Solaris and Linux versions.

port-no. : Port number to be used for communication between the license server pro-gram and Advance CAD. This item can be edited. The value is 7282 at the time of license issue. When changing, use a number not listed in the /etc/services file and which is 1025 or more.

There is basically only one SERVER line, but three lines are required for the redundant server config-uration. When using multiple SERVER line for a redundant server configuration, use the same port-no. for all servers.

(2) Daemon information line

VENDOR daemon-name daemon-dir [option-name]daemon-name : Vendor daemon name.

This item is the name of a program managing application programs that use floating licenses. In Advance CAD, the name is CTCMDARD.

daemon-dir : The name of directory where the vendor daemon resides. This item can be edited. The directory name is arbitrary at the time of license issue. Please edit it to include correct information. Enter the full path to the directory where the vendor daemon resides. The vendor daemon for Advance CAD (CTCMDARD) resides at the exe directory. Therefore, if the home directory of a user who uses Advance Cad is /acad, the daemon directory will be /acad/exe.

option-name : Option file name. This item can be edited. This item is not listed at time of license issue. Option file is used when you want to manage licenses based on users. If not neces-sary, this can be omitted. Enter the full path to the option file name.

(3) Feature information line

FEATURE feature-name daemon-name version date #users borrow checksum code

feature-name : Feature name that can be provided. This item shows the function names that can be provided by each application.

daemon-name : The name of the vendor daemon which controls the function. The name of the vendor daemon that controls Advance CAD features is CTCMDARD.

version : Version number of the function. This is the major version number of Advance CAD. It is not necessary to change this number when Advance CAD under-goes a minor version upgrade.

date : Expiration date of the license. This item is written in the "day-month-year" for-mat. "Day" is a number from 1 to 31, "Month" is a three-letter abbreviation of months in English, and "Year" is a four-digit number. "permanent" 0 means that there is no expiration date.

#users : Maximum number of functions that can be used. This item shows the maxi-mum number of functions that can be provided by each application.

borrow : Maximum duration (hours) in which the license can be borrowed. This is set to 1344 hours (8 weeks).

checksum : Checksum code. This item is used to check validity of each feature line.code : Password for each function.


A.5.2 FLEXnet Publisher TCP/IP port number

From FLEXlm V7.0, the port number to be used for communication between vendor daemon (CTCM-DARD) and client (Advance CAD) can be specified. This function is useful in cases when a client out of a firewall accesses the FLEXnet Publisher server machine inside the firewall. If access via the specified port number is accepted from outside the firewall, access is available for the clients outside the firewall as well. However, please note that this might form a security hole.To use this, write a VENDOR line in the license file.For example, write as follows.

VENDOR CTCMDARD C:\FLEXLM\EXE\CTCMDARD port=1050

By specifying as above, Advance CAD and the vendor daemon CTCMDARD will communicate via port number 1050.The VENDOR line is supported from FLEXlm V7.0 and has the same function as the DAEMON line. Because you cannot specify a port number with the DAEMON line, use the VENDOR line when a port number must be specified. The following shows part of a license file with the VENDOR line specified.

Old license file (part)

SERVER ctc 0123456789ab TCP:7282DAEMON CTCMDARD C:\FLEXLM\EXE\CTCMDARD

A license file with a port number specified for communicating with the vendor daemon (part)

SERVER ctc 0123456789ab TCP:7282VENDOR CTCMDARD C:\FLEXLM\EXE\CTCMDARD port=1050

This function is only available for Advance CAD V15.00 or later.

A.5.3 Merge license files

When other software that adopts FLEXnet Publisher is running, you will have multiple license files issued by corresponding vendors. In this case, if license servers for multiple software are configured to run on the same machine, multiple license files can be merged. Compare the license files. The files that meet the following conditions can be merged. 1) The number of server information lines are the same. 2) The host ID or IDs of the corresponding server information lines are the same. To merge two license files, delete server information from one of the license files and add the remaining lines to the other license file. For safety, create a copy of the original license file in advance.

Suppose there is the following license file.SERVER myserver 000011112222 TCP:7282VENDOR foo C:\path\fooFEATURE foo 1.000 1-jan-0 4 XYY83971C3879A1101F6 ck=15

The following Advance CAD license file is to be merged.SERVER myserver 000011112222 TCP:7282VENDOR CTCMDARD C:\FLEXnet\exe\CTCMDARD.exeFEATURE advancecad_win_base CTCMDARD 19.000 permanent 7 BORROW=1344 \ ck=197 SIGN=9818B6BC7096


The merged file will be as follows.SERVER myserver 000011112222 TCP:7282VENDOR foo C:\path\fooVENDOR CTCMDARD C:\FLEXnet\exe\CTCMDARD.exeFEATURE foo 1.000 1-jan-0 4 XYY83971C3879A1101F6 ck=15FEATURE advancecad_win_base CTCMDARD 19.000 permanent 7 BORROW=1344 \ ck=197 SIGN=9818B6BC7096

There may be a case when a license file cannot or would not be merged. In this case, run separate license server instances for a license file issued by each vendor. Specify different port numbers for all server information lines so none of the lines would have the same number.


A.6 Notes on FLEXnet Publisher (formerly FLEXlm)

A.6.1 Search order of license paths

From FLEXlm Version 7 (Version 6 for Windows), the search order of the licenses changed as follows. (The ver-sion of FLEXnet Publisher (formerly FLEXlm) used by Advance CAD Version 19 is Version 11.4.1.)

• Search order of licenses(1) vendor daemon name_LICENSE_FILE (CTCMDARD_LICENSE_FILE) environment variable(2) .flexlmrc file under the home directory (Unix)

Registry "HKEY_LOCAL_MACHINE\SOFTWARE\FLEXlm License Manager" (Windows)(3) LM_LICENSE_FILE environment variable

• Solaris/Linux versionThe ".flexlmrc" file is created under the home directory when Advance CAD is successfully started.After this file is created, this file is used whenever Advance CAD is started and takes priority over the LM_LICENSE_FILE environment variable. When your license server is changed, delete this file or configure it using the lmpath command (see "A.7.5 Set license environment variables").

• Windows versionA license path is registered under the registry "HKEY_LOCAL_MACHINE\SOFTWARE\FLEXlm License Manager ". This value is created when Advance CAD is successfully started.This registry entry takes priority over the LM_LICENSE_FILE environment variable.When your license server is changed, configure the CTCMDARD_LICENSE_FILE environment variable or use the lmpath command (see "A.7.5 Set license environment variables") or lmtools (see "A.8.5 Configure the license environment variable") to configure.

A.6.2 Notes on obtaining display names (Windows only)

Advance CAD only uses one license when multiple instances of Advance CAD are started on a single display.This is because FLEXnet Publisher keeps attributes such as user name, host name, and display name per obtained license, and Advance CAD adopts a method that the same display name is counted as the one license. This method is the same even if Advance CAD versions are different.


A.7 License management tool

The license management tool is a utility developed and provided by Macrovision Corporation.Use it for license management.

A.7.1 Stop the license server

• lmdownStop the license server.

lmdown [-c license_file] [-q] -c [license_file] : Optional if environment variable LM_LICENSE_FILE is specified-q : Do not display header messages and confirmation messages (use on

occasion such as auto-start)

# lmdown -c /FLEXnet/file/license.liclmutil - Copyright (c) 1989-2004 by Macrovision Corporation. All rights reserved.

Port@Host Vendors1) 7282@myserver CTCMDARD

Are you sure (y/n)? y 1 FLEXlm License Server shut down#

A.7.2 ID lookup of the license server

• lmhostidDisplay the host ID used by the license server.For the Solaris version, the host ID (8 digits) is displayed. For the Windows and Linux version, the MAC address (12 digits) is displayed.

% lmhostidlmhostid - Copyright (c) 1989-2004 by Macrovision Corporation. All rights reserved.The FLEXnet Licensing host ID of this machine is "12345678"%

A.7.3 Re-read the license file

• lmrereadRequest the license daemon to re-read the license file, to update to the current license information.This function is useful when a license is added later (such as for optional software), or when a license is not released after exiting CAD.

% lmrereadlmhostid - Copyright (c) 1989-2004 by Macrovision Corporation. All rights reserved.lmreread successful%


A.7.4 Monitor the license status

• lmstatMonitor the license status.Information such as the current license usage can be checked.

Common options-a Display all items.-c [license_file] Specify the license file to use.

When omitted, the license file specified by the environment variable LM_LICENSE_FILE is used.

% lmstat -a -c /FLEXnet/file/license.liclmutil - Copyright (c) 1989-2004 by Macrovision Corporation. All rights reserved.Flexible License Manager status on Mon 8/23/2004 10:43

License server status: 7282@myserver License file(s) on tit: /FLEXnet/file/license.lic:

myserver: license server UP (MASTER) v11.4.1

Vendor daemon status (on myserver):

CTCMDARD: UP v11.4.1

Feature usage info:

Users of advancecad_base: (Total of 5 licenses issued; Total of 0 licenses in use)

Users of advancecad_dxf: (Total of 2 licenses issued; Total of 0 licenses in use)

Users of advancecad_font: (Total of 1 license issued; Total of 0 licenses in use)

Users of advancecad_win_base: (Total of 3 licenses issued; Total of 0 licenses in use)

Users of advancecad_win_dxf: (Total of 1 license issued; Total of 0 licenses in use)

Users of advancecad_win_pid: (Total of 1 license issued; Total of 0 licenses in use)

Users of advancecad_win_sd: (Total of 1 license issued; Total of 0 licenses in use)

Users of advancecad_win_font: (Total of 1 license issued; Total of 0 licenses in use)

%

A.7.5 Set license environment variables

• lmpathSet license environment variables.The variables set from this command is saved in the .flexlm file.

Common options-status Display the current environment variables.


-override {all|vendor} path "all": Environment variable LM_LICENSE_FILE, "vendor": Environment variable daemon-name__LICENSE_FILE (for Advance CAD, CTCMDARD_LICENSE_FILE) are set.

-add {all|vendor} path "all": Environment variable LM_LICENSE_FILE, "vendor": Environment variable daemon-name__LICENSE_FILE (for Advance CAD, CTCMDARD_LICENSE_FILE) will have PATH added.

• To delete the CTCMDARD_LICENSE_FILE environment variable% lmpath -override CTCMDARD ""% lmpath -override CTCMDARD ""lmpath - Copyright (c) 1989-2004 by Macrovision Corporation. All rights reserved.New path for CTCMDARD_LICENSE_FILE: %

• To delete the LM_LICENSE_FILE environment variable% lmpath -override all ""lmpath - Copyright (c) 1989-2004 by Macrovision Corporation. All rights reserved.New path for LM_LICENSE_FILE: %

A.7.6 Check license version

• lmverDisplay the versions of FLEXlm -related modules.

# lmver [lmgrd|Vendor daemon name]

% ./lmver CTCMDARDlmutil - Copyright (c) 1989-2004 by Macrovision Corporation. All rights reserved.FLEXnet Licensing v11.4.1 (liblmgr.a), Copyright (c) 1988-2004 by Macrovision Corporation. All rights reserved.%

A.7.7 Borrow a license

There are cases when you want to use Advance CAD for a short period installed on a laptop out of office in a meeting or a business trip. This is possible if the license server in your office permits access over the firewall, but it is generally not permitted due to security issues.In this case, you can use the FLEXlm Borrow function to temporarily borrow a license for using Advance CAD.After the borrowing period expires, you will not be able to start Advance CAD.On the other hand, the number of borrowed licenses is subtracted from the license server. When the borrowing period expires, or the license is returned before expiration, the number of licenses is restored.

lmborrowBorrow a license from the server. This command supports users to check out the license.

Common options{all|vendor} enddate[time] "all": Specify vendor daemons for all license servers accessible from

the client. "vendor": Specify for each vendor daemon. For Advance CAD, specify CTCMDARD. "enddate [time]": Specify the return date of the license.

-status Display the current status.


-clear "all": Environment variable LM_LICENSE_FILE, "vendor": daemon-name__LICENSE_FILE environment variable (for Advance CAD, CTCMDARD_LICENSE_FILE) will have the speci-fied PATH added.

-return [-c licensefile] [-c licensefile] [-d display_name] [-fqdn] feature Return the borrowed license before expiration.

A.7.7.1 Borrow a license

lmborrow {vendor|all} Enddate [time]"vendor": : Specify borrow settings for each vendor daemon. For Advance CAD, specify

CTCMDARD. Specify ALL to specify all vendor daemons.Enddate[time] : Specify a return date. Use the dd-mmm-yyyy format. The maximum borrow-

ing duration is two weeks. Specify time by hh:mm. When time is omitted, the duration will last until end of the specified day(23:59).

Borrow procedure(1) Issue a lmborrow command (For Windows only, lmtools is also accepted).(2) Check out a license (StartAdvance CAD. To borrow options at the same time, use an option

command to obtain a license).(3) Check with lmborrow -status.

Example Solaris versionacad % lmborrow CTCMDARD 27-Aug-2004lmborrow - Copyright (c) 1989-2004 by Macrovision Corporation. All rights reserved.Setting LM_BORROW=23-aug-2004:CTCMDARD:27-Aug-2004acad % acad % work/home/acad/workwork % acadwork % lmborrow -statuslmborrow - Copyright (c) 1989-2004 by Macrovision Corporation. All rights reserved.Vendor Feature Expiration______ ________ __________

CTCMDARD advancecad_base 27-Aug-04 23:59CTCMDARD advancecad_font 27-Aug-04 23:59work %

Example Windows versionC:\acad>lmborrow CTCMDARD 27-Aug-2004 12:00lmborrow - Copyright (c) 1989-2004 by Macrovision Corporation. All rights reserved.Setting LM_BORROW=20-aug-2004:CTCMDARD:27-Aug-2004:12:00C:\acad>work

C:\acad\work>acad

C:\acad\work>lmborrow -statuslmborrow - Copyright (c) 1989-2004 by Macrovision Corporation. All rights reserved.Vendor Feature Expiration______ ________ __________

CTCMDARD advancecad_win_base 27-Aug-04 11:59CTCMDARD advancecad_win_font 27-Aug-04 11:59

C:\acad\work>


A.7.7.2 Check status of a borrowed license

lmborrow -status-status : Display the current borrow status.

C:\acad>lmborrow -statuslmborrow - Copyright (c) 1989-2004 by Macrovision Corporation. All rights reserved.Vendor Feature Expiration______ ________ __________


A.7.7.3 Return a borrowed license before expiration

lmborrow -return [-c licensefile] [-d display_name] [-fqdn] feature

Example Solaris versionwork % lmborrow -statuslmborrow - Copyright (c) 1989-2004 by Macrovision Corporation. All rights reserved.Vendor Feature Expiration______ ________ __________

CTCMDARD advancecad_base 27-Aug-04 23:59CTCMDARD advancecad_font 27-Aug-04 23:59work %work % lmborrow -return -d ctc:0 advancecad_fontlmborrow - Copyright (c) 1989-2004 by Macrovision Corporation. All rights reserved.work % lmborrow -return -d ctc:0 advancecad_baselmborrow - Copyright (c) 1989-2004 by Macrovision Corporation. All rights reserved.work % lmborrow -statuslmborrow - Copyright (c) 1989-2004 by Macrovision Corporation. All rights reserved.work %

Example Windows versionC:\acad>lmborrow -statuslmborrow - Copyright (c) 1989-2004 by Macrovision Corporation. All rights reserved.Vendor Feature Expiration______ ________ __________


C:\acad>lmborrow -return -d CTC:0 advancecad_win_fontlmborrow - Copyright (c) 1989-2004 by Macrovision Corporation. All rights reserved.C:\acad>lmborrow -return -d CTC:0 advancecad_win_fontlmborrow - Copyright (c) 1989-2004 by Macrovision Corporation. All rights reserved.C:\acad>lmborrow -statuslmborrow - Copyright (c) 1989-2004 by Macrovision Corporation. All rights reserved.

C:\acad>

* For [display_name], use the name displayed with lmstat -a. (The value is case sensitive.)

% lmstat -almstat - Copyright (c) 1989-2004 by Macrovision Corporation. All rights reserved.Flexible License Manager status on Mon 8/23/2004 11:38 AM


License server status: 7283@myserver License file(s) on myserver: /FLEXnet/file/license.lic:

myserver: license server UP (MASTER) v11.4.1

Vendor daemon status (on myserver):


Feature usage info:

Users of advancecad_base: (Total of 5 licenses issued; Total of 1 license in use)

"advancecad_base" v19.000, vendor: CTCMDARD: floating license

acad tit ctc:0 (v19) (myserver/7283 161), start Mon 8/23 11:30 (linger: 390540)

C:\>lmstat -almstat - Copyright (c) 1989-2004 by Macrovision Corporation. All rights reserved.Flexible License Manager status on Mon 8/23/2004 4:48 PM

[Detecting lmgrd processes...]License server status: 7283@myserver License file(s) on cat: C:\FLEXnet\files\license.lic:

cat: license server UP (MASTER) v11.4.1

Vendor daemon status (on cat):


Feature usage info:

Users of advancecad_win_base: (Total of 7 licenses issued; Total of 1 licensein use)

"advancecad_win_base" v19.000, vendor: CTCMDARD: floating license

acad ELK ELK:0 (v19) (myserver/7282 314), start Mon 8/23 16:47


A.8 License management tool (Windows only)

A.8.1 Stop the license server

Start lmtools, and select the [Start/Stop/Reread] tab. Click the [Stop Server] button.

A.8.2 Re-read the license file

Start lmtools, and select the [Start/Stop/Reread] tab. Click the [ReRead License File] button.


A.8.3 Monitor the license status

Start lmtools, and select the [Server Status] tab. Click the [Perform Status Enquiry] button.

A.8.4 Check license version

Start lmtools, and select the [Utilities] tab. In the [File Name] text box, enter the FLEXlm file to look up (use BROWSE to specify a file). Then click the [Find Version] button.

A.8.5 Configure the license environment variable

Start lmtools, and select the [Utilities] tab.• Check environment variables

Click the [List All Vendor Paths] button to display the license search paths registered in the registry.

• Add new Register "CTCMDARD" to the [Vendor Name] text box. Enter the license file to be modified in the [Path] text box and click the [Add Vendor Path] button.


• Change To change the search path due to server replacement or other reasons, enter the vendor name of the software to modify in the [Vendor Name] text box. Enter the new license file name in the [Path] text box and click the [Override Path] button.

• Delete Enter the vendor name of the software to delete in the [Vender Name] text box. In the [ Path] text box, enter two double quotation marks (") and click the [Override Path] button.

A.8.6 Borrow a license

Start lmtools, and select the [Borrowing] tab.

A.8.6.1 Borrow

By borrowing a license from a license server, you can continue using the application even after connection to the server is lost.


(1) In the [Vendor Name] text box, enter the vendor daemon name (CTCMDARD). In the [Return Date] text box, enter the date to end borrow license. In the [Return Time] text box, enter the time (when omit-ted, 23:59 set). Click the [Set Borrow Expiration] button. The maximum borrow period is two weeks (336 hours).

(2) Check out the license (obtain the license using Advance CAD).(3) Check with the [List Currently Borrowed Features] button.

A.8.6.2 Return

Perform the following procedures to return a license before expiration.When the expiration date comes, the license is automatically returned and cannot be used anymore.

(1) In the [Display Name] text box, enter the display name. Fill the [Feature Name] text box, and click the [Return Borrowed License Early] button. For the display name, enter the display name listed in the [Server Status] tab. For the feature name, enter the feature name displayed with the [List Currently Borrowed Features] button.


A.9 About the Windows firewall

From Windows XP Professional Service Pack 2 (hereafter referred to as "SP2"), Windows Firewall (formerly Inter-net Connection Firewall, hereafter referred to as "firewall") is enabled. Because the connection between the Advance CAD client and the license manager is blocked, Advance CAD cannot be started. To start the Advance CAD license manager on SP2, perform one of the following according to your environment.

• Register the FLEXnet Publisher daemon and vendor daemons to the exceptions of the firewall • Register the ports used by FLEXnet Publisher to the exceptions of the firewall

Note) This task must be done by a user who has Administrators rights.

A.9.1 Method 1: Register the FLEXnet Publisher module as an exception

(1) From the [Start] menu, select [Control Panel] > [Security Center] to start [Windows Firewall].(2) Select the [Exception] tab.


(3) Register exception Click the [Add Program (R)] button, and add lmgrd.exe and CTCMDARD.exe of FLEXnet Publisher.

Click the [Browse (B)] button to the browse window.In the browse window, select lmgrd.exe. (lmgrd.exe and CTCMDARD.exe are located under the <FLEXlm installation directory>\exe).


lmgrd.exe is added.

Similarly, add CTCMDARD.exe.

Now, FLEXnet Publisher modules are registered as exceptions.


A.9.2 Method 2: Register the ports used by FLEXnet Publisher as exceptions

(1) Add port=xxxxx at the end of the VENDOR line. (Select port number xxxxx that is not used by another application.)

SERVER server 00000000000 TCP:7282 VENDOR CTCMDARD C:\FLEXlm\EXE\CTCMDARD.exe INCREMENT advancecad_base CTCMDARD 19.000 31-Dec-2004 1 ED91D1E607EBBC51F9ED \ ck=98

↓

SERVER server 000000000000 TCP:7282 VENDOR CTCMDARD C:\FLEXlm\EXE\CTCMDARD.exe port=xxxxx INCREMENT advancecad_base CTCMDARD 19.000 31-Dec-2004 1 ED91D1E607EBBC51F9ED \ ck=98

(2) Add TCP port 7282 for the SERVER line and xxxxx for the VENDOR line. Click the [Add Port (R)] button to add 7282 and xxxxx.


To register the TCP port by the master daemon, enter an arbitrary name in [Name], 7282 in [Port Num-ber], select TCP and click the [OK] button.

To register the TCP port by the vendor daemon, enter an arbitrary name in [Name], xxxxx (17282 in the example below) in [Port Number], select TCP and click the [OK] button.


A.10 License manager: Frequently asked questions

The following section explains some of the error messages when using FLEXlm.Use the information for troubleshooting.

[Message]"Erro getting license file data""license file is XXXXX" (XXXXX: Value of environment variable LM_LICENSE_FILE)

(Action)A license file is not found in the specified location. Check the license file location.

[Message]"### Warning: This machine's date is invalid !!!"" or Did you back the date of machine ?"

(Action)The date of the machine might be modified. If past date is used, set the current date.

[Message]"Maximum # users for "XXXX" reached. " (XXXX: feature name)

(Action)All licenses are used. Stop an unused Advance CAD instance. Or, add a license.

[Message] "Wrong host for XXXX"

(Action)The ID specified in the license does not match with the node that the software is running on. Check the license file ID.

[Message]"XXXX in license.dat has expired"

(Action)License has expired. Check the license expiration date.

[Message]"Clock difference is too long between client/server"

(Action)The dates of the client and server systems do not match. In Advance CAD, the tolerance of time differ-ence between the server and client is set to 27 minutes.

[Message]"Please install NWlink IPX/SPX driver." (Windows only)

(Action)NWlink IPX/SPX is not installed and the Ethernet address cannot be obtained. Check that [NWLink IPX/SPX/NetBIOS Compatible Transport Protocol] exists in [Control Panel] > [Network] > [Protocol] tab.

* From Version 13 or later, client machines will no longer need the IPX/SPX protocol.


[Message]"hostname: Wrong hostid, exiting"

(Action)ID and host name do not match. Check that the host name in the SERVER line of the license file and the server host name matches.

[Question]What is the license check interval? How much is the network load regarding the check?

(Answer)Advance CAD Version 9.00 to Version 11.xx polls the license every 30 seconds and Advance CAD Ver-sion 12.00 or later polls the license every 300 seconds to check the license. The load for the check is about the same as the ping command (less than 150 bytes).


A.11 License management utility operation example

lmcksum

• UNIX version

% /home/acad/exe/lmcksumlmcksum - Copyright (C) 1989-2001 Globetrotter Software, Inc.lmcksum: using license file "/home/acad/uenv/license.dat"

213: SERVER yak 830f0496 7282 187: DAEMON CTCMDARD /home/acad/exe/OK: 34: FEATURE advancecad.base CTCMDARD 19.000 1-jan-0 5 2CDCBB1212516CF719D5 ck=34OK: 28: FEATURE advancecad.rcadam CTCMDARD 19.000 1-jan-0 3 8C0C4B024128B3BA775F ck=28OK: 55: FEATURE advancecad.mcx CTCMDARD 19.000 1-jan-0 3 0C0CAB4219C0AFD27AC2 ck=55OK: 47: FEATURE advancecad.mcadam CTCMDARD 19.000 1-jan-0 3 9C2C5B522F3DB3937786 ck=47OK: 71: FEATURE advancecad.dxf CTCMDARD 19.000 1-jan-0 3 FC9CAB020FB5BFC973CC ck=71OK: 129: FEATURE advancecad.nc CTCMDARD 19.000 1-jan-0 3 6C0CFB72D0EDB81B1C21 ck=129OK: 50: FEATURE advancecad.pid CTCMDARD 19.000 1-jan-0 3 ECAC2B520D26E7B564CE ck=50OK: 69: FEATURE advancecad.sd CTCMDARD 19.000 1-jan-0 3 5CBC1BB2D0F2F2001721 ck=69OK: 74: FEATURE advancecad.font CTCMDARD 19.000 1-jan-0 1 2C9C8BF2FA1758FAE4E5 ck=74OK: 73: FEATURE advancecad.parts CTCMDARD 19.000 1-jan-0 1 5C2C8BB28C30F54B1F5A ck=73OK: 83: FEATURE advancecad_win.base CTCMDARD 19.000 1-jan-0 5 6C0C2B1296945EC8DE4D ck=83OK: 77: FEATURE advancecad_win.rcadam CTCMDARD 19.000 1-jan-0 3 7C8CABF25150D3075D17 ck=77OK: 94: FEATURE advancecad_win.mcx CTCMDARD 19.000 1-jan-0 3 DC2C9BB2DBEDA66E402B ck=94OK: 89: FEATURE advancecad_win.mcadam CTCMDARD 19.000 1-jan-0 3 9C3CAB82E650C50E7882 ck=89OK: 35: FEATURE advancecad_win.dxf CTCMDARD 19.000 1-jan-0 3 DC7CABB2CB0A921E307D ck=35OK: 151: FEATURE advancecad_win.nc CTCMDARD 19.000 1-jan-0 3 BCACBB229CACD725F1A3 ck=151OK: 99: FEATURE advancecad_win.pid CTCMDARD 19.000 1-jan-0 3 BC7CAB42E2F3A8592F44 ck=99OK: 171: FEATURE advancecad_win.sd CTCMDARD 19.000 1-jan-0 3 AC9CBB227EA9DD1DDBC1 ck=171OK: 102: FEATURE advancecad_win.works CTCMDARD 19.000 1-jan-0 3 DC9C7B42E7BE05E08594 ck=102OK: 76: FEATURE advancecad_win.font CTCMDARD 19.000 1-jan-0 1 ECBCEBE2B2022D80D777 ck=76OK: 123: FEATURE advancecad_win.parts CTCMDARD 19.000 1-jan-0 1 CC7C5B9273D5D9BE8A3B ck=12 102: (overall file checksum)

• Windows version

C:\acad\exe>lmutil lmcksumlmutil - Copyright (C) 1989-2001 Globetrotter Software, Inc.lmcksum: using license file "C:\acad\uenv\license.dat"

161: SERVER CTC 000000000000 TCP:7282 187: DAEMON CTCMDARD C:\acad\exe\CTCMDARDOK: 77: FEATURE advancecad_win.base CTCMDARD 19.000 20-aug-2002 1 CCE6AB7647755E9A8CAF ck=77OK: 30: FEATURE advancecad_win.rcadam CTCMDARD 19.000 20-aug-2002 1 7CC69B76C1FDB652C81B ck=30OK: 25: FEATURE advancecad_win.mcx CTCMDARD 19.000 20-aug-2002 1 5CD6FBC665705509AB15 ck=25


OK: 61: FEATURE advancecad_win.mcadam CTCMDARD 19.000 20-aug-2002 1 7CC6AB86F02CC761F7DD ck=61OK: 79: FEATURE advancecad_win.dxf CTCMDARD 19.000 20-aug-2002 1 5C86FBD61D26509D5CCF ck=79OK: 79: FEATURE advancecad_win.nc CTCMDARD 19.000 20-aug-2002 1 BCC6CBB69D482A81B12E ck=79OK: 15: FEATURE advancecad_win.pid CTCMDARD 19.000 20-aug-2002 1 6C769B16626BE20AB01F ck=15OK: 43: FEATURE advancecad_win.sd CTCMDARD 19.000 20-aug-2002 1 BC76DBC697C23371264C ck=43OK: 93: FEATURE advancecad_win.works CTCMDARD 19.000 20-aug-2002 1 0C762BC61E4CEC61D03C ck=93OK: 97: FEATURE advancecad_win.font CTCMDARD 19.000 20-aug-2002 1 DC369BF65D58788D97A7 ck=97OK: 80: FEATURE advancecad_win.parts CTCMDARD 19.000 20-aug-2002 1 1CA63B86255AF954EA3A ck=80 43: (overall file checksum)

lmdown

• UNIX version

# /acad/exe/lmdownlmdown - Copyright (C) 1989-2001 Globetrotter Software, Inc.

Port@Host Vendors1) 7282@ctc CTCMDARD sunwlicd

Are you sure (y/n)? yShut down FLEXlm server on node ctc 1 FLEXlm License Server shut down

• Windows version

C:\acad\exe>lmutil lmdownlmutil - Copyright (C) 1989-2001 Globetrotter Software, Inc.[Detecting lmgrd processes...]

Port@Host Vendors1) 7282@CTC CTCMDARD

Are you sure (y/n)? y 1 FLEXlm License Server shut down

lmhostid

• UNIX version

% lmhostidlmhostid - Copyright (C) 1989-2001 Globetrotter Software, Inc.The FLEXlm host ID of this machine is "8070bdd3"

• Windows versionC:\acad\exe>lmutil lmhostidlmutil - Copyright (C) 1989-2001 Globetrotter Software, Inc.The FLEXlm host ID of this machine is "08002be7335d"


Example: lmstat

• UNIX version

% lmstat -a lmstat - Copyright (C) 1989-2001 Globetrotter Software, Inc.Flexible License Manager status on Thu 5/23/2002 19:42

License server status: 7282@ctc License file(s) on ctc: /home/acad/uenv/license.dat:

ctc: license server UP (MASTER) v11.4.1

Vendor daemon status (on yak):


Feature usage info:

Users of advancecad.base: (Total of 5 licenses available)

Users of advancecad.rcadam: (Total of 3 licenses available)

Users of advancecad.mcx: (Total of 3 licenses available)

Users of advancecad.mcadam: (Total of 3 licenses available)

Users of advancecad.dxf: (Total of 3 licenses available)

Users of advancecad.nc: (Total of 3 licenses available)

Users of advancecad.pid: (Total of 3 licenses available)

Users of advancecad.sd: (Total of 3 licenses available)

Users of advancecad.font: (Total of 1 license available)

Users of advancecad.parts: (Total of 1 license available)

• Windows version

C:\acad\exe>lmutil lmstat -almutil - Copyright (C) 1989-2001 Globetrotter Software, Inc.Flexible License Manager status on Thu 5/23/2002 7:45 PM

[Detecting lmgrd processes...]License server status: 7282@CTC License file(s) on CTC: C:\acad\uenv\license.dat:

CTC: license server UP (MASTER) v11.4.1

Vendor daemon status (on CTC):


Feature usage info:


Users of advancecad_win.base: (Total of 5 licenses available)

"advancecad_win.base" v19.000, vendor: CTCMDARD: floating license

user1 acad1 ACAD1:0 (v19) (CTC/7282 1160), start Thu 5/23 19:14 usre2 acad2 ACAD2:0 (v19) (CTC/7282 886), start Thu 5/23 19:29

Users of advancecad_win.rcadam: (Total of 2 licenses available)

Users of advancecad_win.mcx: (Total of 2 licenses available)

Users of advancecad_win.mcadam: (Total of 2 licenses available)

Users of advancecad_win.dxf: (Total of 2 licenses available)

Users of advancecad_win.nc: (Total of 2 licenses available)

Users of advancecad_win.pid: (Total of 2 licenses available)

Users of advancecad_win.sd: (Total of 2 licenses available)

Users of advancecad_win.font: (Total of 1 licenses available)

"advancecad_win.font" v19.000, vendor: CTCMDARD: floating license

user1 acad1 ACAD1:0 (v19) (CTC/7282 250), start Thu 5/23 19:14

Users of advancecad_win.parts: (Total of 1 licenses available)

Users of advancecad_win.works: (Total of 2 licenses available)


Index

Symbols.flexlmr ........................................ 51

AACAD.SET ................................. 28ACAD_SET ................................ 28Administrators ............................ 8aplot.bat ...................................... 30Association ................................. 29

EEthernet address ....................... 6

FFEATURE .................................. 47Feature information line ........... 47

Hhcopy.bat .................................... 30HKEY_LOCAL_MACHINE ...... 51Host ID ........................................ 5Host name .................................. 5 47hosts ............................................ 21

Iipconfig ....................................... 5 6

LLicense server ........................... 41lmborrow ..................................... 54lmdown ....................................... 52lmhostid ...................................... 52LM_LICENSE_FILE .................. 27 28lmreread ..................................... 52lmstat .......................................... 53lmver ........................................... 54

Ooplot.bat ...................................... 30

PPage file size ............................. 4PATH .......................................... 28Port@hostname ........................ 27PortID@ server name .............. 27

Qqplot.bat ...................................... 30

RRedundant servers ................... 27Registry ...................................... 51

SSERVER ..................................... 47Server information line .............. 47

VVENDOR ..................................... 47Vendor daemon information line 47Vendor daemon name_LICENSE_FILE 51Visual C++ .................................. 4

WWindows ..................................... 1Windows firewall ........................ 62Windows XP ............................... 1Windows XP Professional Service Pack 2 62

75

Index

76

Installation Guide - 伊藤忠テクノソリューションズacad/pdf/v19/install_E.pdf2.1...

Documents

Transcript of Installation Guide - 伊藤忠テクノソリューションズacad/pdf/v19/install_E.pdf2.1...