Installation Abovethe Instructions · PDF fileQuestions? CM1800.GECARES (800.432.2737) ......

InstallationInstructions

AbovetheCooktopOvenJVM1600 Series

Questions? CM1800.GECARES (800.432.2737) or Visit our Website at: ge.com

BEFORE YOU BEGINRead these instructions completely and carefully.

• IMPORTANT - S_,,etheseinstructions for local inspector's use.

• IMPORTANT - Obse,,e_,llgoverning codes and ordinances.

• Note to Installer - Be sure to leave these

instructions with the Consumer.

• Note to Consumer - KeeI) these instructionsfor fllture reference.

• Skill level - Installation of this appliance requiresbasic mechanical and electrical skills.

• Proper installation is the responsibility of the installer.

• Product tailure due to improper installation is notcoxered under the _'arrantx.

3828W5U0477

49-40469-1

09-06 JR

READ CAREFULLY.

KEEP THESE iNSTRUCTiONS.

Installation Instructions

CONTENTS

General information

Important Safety Instructions .................................. 3

Electrical Requirements .......................................... 3

Hood Exhaust ....................................... 4, 5

Damage--Shipment/Installation .............................. 6

Parts Included. ......................................... 6

Tools You Will Need ............................................... 7

Mounting Space ...................................................... 7

Step-by-step installation guide

Placement of Mounting Plate ............................ 8-10

Removing tire Mounting Plate ...................... 8

Finding the _4all Studs ................................. 8

Determining _all Plate Loration .................. 9

Aliguiug the Wall Plate ............................... 10

Installation Types .................................. 11-22

[] ()utside Top Exhaust ............................ 12-14

Attach Mounting Plate to _'dl ....... 12

Prepa_ltion of Top Cabinet .......... 13

Assemble and Install Adaptor. ............. 13

Mount the Oveu .................... 13, 14

A(!just the Exhaust Adaptor .......... 14

Connecting Durtwork .......................... 14

_ Outside Back Exhaust ............................ 15-18

Preparing Rear _all ti)rOutside Back Exhaust .......................... 15

Attach Exhaust Adaptor toOven Rear Panel .................................. 15

Attach Mounting Plate to _4"dl ....... 16

Prepa_ltion of Top Cabinet .......... 16

Adapting Blower tor OutsideBack Exhaust. ......................................... 17

Mount the Oveu .................................. 18

_] Redrculating ........................................ 19-22

Attach Mounting Plate to _'dl ....... 19

Prepal_ltion of Top Cabinet .......... 19

Adapting Blower torRecirculation .............................. 20, 21

Mount the Oveu .................... 21, 22

Installing the Charcoal Filter ...... ........ 22

Before You Use Your Oven .................................. 23

2


iMPORTANT SAFETY iNSTRUCTiONS

This product requires a three-i)rong grounded outlet.Tile installer must perform a ground contimfitv checkoil the power outlet box before beginning tileinstallation to insure that the outlet box is properlygrounded. If not properly gromlded, or if tile outletbox does not meet electrical requirements noted(under EI,ECTRICAI, REQLIIREMENTS), a qualifiedelectrician should be employed to correct anydeficiencies.

w

lll//ll// 1

p

CAUTION:For personal safety, removehouse fuse or open circuitbreaker before beginninginstallation to avoid severe

or fatal shock injury.

CAUTION: ForpersonalsafeS,themounting

surface must be capable of supporting the cabinet load,in addition to the added weight of this 63-85 poundproduct, plus additional oven loads of up to 50 poundsor a total weight of 113-135 pounds.

CAUTION: For personal safety, this product

ca_mot be installed in cabinet arrangements such as anisland or a peninsula. It must be mounted to BOTHa top cabinet AND a waJL

NOTE: For easier installation and personal safety, it isrecommended that two people install tlfis product.

IMPORTANT--PLEASE READ CAREFULLY. FORPERSONAL SAFETY, THIS APPLIANCE MUST BEPROPERLY GROUNDED TO AVOID SEVERE ORFATAL SHOCK.

Insure properground existsbefore use

Tile power cord of thisappliaJace is equipped witha three-prong (grounding)plug which mates witha standard three-prong(grounding) wall receptacleto m_ize the possibilityof electric shock hazard

from tlfis appliance.

You should have the wall receptacle and circuit checkedby a qualified electrician to make sure the receptacle isproperly grounded.

Where a standard two-prong wall receptacle isencountered, it is very important to have it replacedwith a properly grounded three-prong wa3l receptacle,installed by a qualified electriciaaa.

DO NOT, UNDFa;t ANY CIRCUMSTANCES, CUT,DI?_'ORM OR REMOVE ANY OF THE PRONGSFROM THE POWER CORD. DO NOT USE WITHAN EXTENSION CORD.

ELECTRICALREQUIREMENTSProdurt rating is 120 volts AC, 60 He_z, 14 amps and

1.60 kilowatts. This product must be connected to asupply drcuit of tile proper voltage and _'equencv.

Wire size must confimn to the requirements of theNational Electrical (?,ode or the l)re\;filing local code

for this kilowatt rating. The power supply cord andplug should be brought to a separate l 5 to 20 ampere

branch drcuit single grotmded outlet. The outlet boxshould be located in the cabinet abo\v the oren. The

outlet box and supply drctfit should be installed bya qualified electddan and confiwm to the NationalElectrical Code or the pre\uiling local code.

3


HOOD EXHAUSTNOTE: Read these next two pages only if you plml to vent your exhaust to theoutside. If you plan to recirculate the air back into the room, proceed to page 6.

OUTSIDE TOP EXHAUST (EXAMPLE ONLY)

The following chart describes an example ot one possibleductwork instnllation.

DUCT PIECES

EQUIVALENT NUMBER

LENGTH x USED

RoofCap 24 Ft. x12Ft.StraightDuct 12Ft. x(6" Round)

-_ Rectangular-to-Round 5Ft. xTransitionAdaptors

Equivalentlengthsof duct piecesare basedonactualtests andreflect requirementsfor goodventingperformancewith anyventhood.

(1)

(1)

(1)

Total Length

EQUWALENT

LENGTH

24 Ft.

12Ft.

5Ft.

41 Ft.

*IMPORTANT: If a rectangula_to-rotmd transition adaptor is used, the bottom corners of the damper will

haxe to be cut to fit, using the tin snips, in order to allow free moxement of the damper.

OUTSIDE BACK EXHAUST (EXAMPLE ONLY)

The following chart describes an example ot one possibleductwork installation.

EQUIVALENT NUMBER EQUIVALENT

DUCT PIECES LENGTH* x USED -- LENGTH

_Wall Cap 40Ft. x (1) 40Ft.

3 Ft.StraightDuct 3 Ft. x (1) 3 Ft.

3W' x 10" Rectangular)

(_ 90° Elbow 10Ft. x (2) 20Ft.

Equivalentlengthsof ductpiecesare basedonactualtests andreflect requirementsfor goodventingperformancewith anyvent hood.

Total Length = 63 Ft.

NOTE: For back exhaust, care should be taken to align exhaust with space between studs, or wall should be prepared

at the time it is constructed by leaving enough space between the wall studs to accommodate exhaust.

4


NOTE: If wm need to install ducts, note that the total

duct lengti_ of 3¼" x ] 0" rectangular or 6" diameter

round duct should not exceed 120 equivalent feet.

Outside ventilation requires a HOOD EXHAUST DUCT.Read the fi_llowing careflfllv:

NOTE: It is important that venting be installed usingthe most direct route and with as few elbows as possible.

This ensures clear venting of exhaust and helps preventblockages. Also, make sure dmnpers swing freely and

nothing is blocking the ducts.

Exhaust connection:

The hood exhaust has been designed to mate with a

standard 3¼" x 10" rectangular duct.

If a round duct is required, a rectangula_to-round

transition adaptor must be used. Do not use less thana 6" diameter duct.

Maximum duct length:For s;Kislhctorv air movement, the total duct length of

3¼" x 10" rectangular or 6" diameter round duct should

not exceed 120 equivalent feet.

Elbows, transitions, wall and roof caps,etc., present additional resistance to airth,w and areeqtfiwdent to a section of straight duct which is longer

than their actual physical size, When calculating the

total duct length, add the eqtfiwdent lengths of all

transitions and adaptors plus the length of all straight

duct sections, The chart below shows you how to

calculate total eqtfiwdent ductwork length using the

approximate leer of eqtfiwdent length of some

typical ducts.

EQUIVALENT NUMBER EQUIVALENT

DUCT PIECES LENGTH x USED = LENGTH

Rectangular-to-Round 5Ft. x ( ) = Ft.TransitionAdapto¢

Wall Cap 40 Ft. x ( ) = Ft.

()_ 90° Elbow 10Ft. x ( ) = Ft.

45° Elbow 5Ft. x ( ) = Ft.

90° Elbow 25 Ft, x ( ) = Ft,

45° Elbow 5Ft. x ( ) = Ft.

RoofCap 24 Ft. x ( ) = Ft.

StraightDuct6" Roundor 1Ft. x ( ) = Ft.3W' x 10" Rectangular

Total Duetwork = Ft.

* IMPORTANT: If a re<tangtdar-to-round transilion Equivalenl 1<ngths o[ du<t pie_ es are bas(d on aclual lests

adaptor is use(L the bottom corners of Ihe d_llllpeF _/lld reflect requirem_ nls tk)r good venling performance x_itllxdll have to be Ctll tO _lt, using the tin snips, in order any vent hood.to allm_fl-ee llll)_,{_lll( 111 of Ih( d{llllpel.

5


DAMAGE - SHIPMENT/iNSTALLATiON

* If the unit is damaged in shipment, retm'n the

unit to the store in which it was bought fl)r repair

or replacement.

o If the _it is damaged by the customer, repair or

replacement is the Iesponsibility of the customer.

o If the unit is damaged by the installer (if other

than the customer), repair or replacement must

be made by arrangement between customer andinstaller.

PARTS INCLUDED

HARDWARE PACKET

PART QUANTITY

Wood Screws 2(¼" x 2")

ToggleBolts(and 4wing nuts)(¼" x 3")

Self-aligningMachine 3Screws(W'-28 x 3Y4")

NylonGrommet 2(for metal cabinets)

Metal Screws 1 black(W' x 1_,,) 2 bronze

Power Cord Strap 1

(plastic)

You will find the installation hardware contained in

a packet with the unit. Check to make sure w)u have

all these parts.

NOTE: Some extra parts are included.

PARTS iNCLUDED

ADDITIONAL PARTS

QUANTITY

TOP CABINET TEMPLATE

REARWALL

TEMPLATE

-------._.__.__

INSTALLATIONiNSTRUCTIONS

TopCabinetTemplate

RearWallTemplate

InstallationInstructions

SeparatelyPackedGreaseFilters

CharcoalFilter(onsomemodels)

ExhaustAdaptor

Damper

6


TOOLS YOU WILL NEED

# 1 and#2PhillipsscrewdriverPencil

Tinsnips(forcuttingdamper,if required) Scissors

(to cut template,if necessary)

Gloves

Safetygoggles

Saw(saber,holeor keyhole)

Ruleror tape measure

aightedge

Electricdrill with s/116",7/11g',syu,-1½-and%" drill bits

Studfinder er Hammer(optional)

Level

Carpentersquare

(optional)

Fillerblocksor scrapwoodpieces,if neededfor top cabinetspacing(usedon recessedbottomcabinet installationsonly)

Ductandmaskingtape

MOUNTING SPACE

II] t[] IIINOTE:Maximumcabinetdepth is 13".

ill

66" ormorefromthe floor

to the top oftheoven

\

Bottomedgeofcabinetneedsto

be30" or morefromthe cooking

surface

Backsplash

NOTES:

" The space between the cabinets must be 30"wide and fl'ee of obst_ uctions.

• If the space between the cabinets is greaterthan 30", a Filler Panel Kit may be used to fill

in the gap between the oven and the cabinets.Yore" Owner's Manual contains the kit nmnberfor vour model.

• This oven is tot installation over ranges up to36" wide.

• If win are going to vent w)m" oven to the outside,see Hood Exhaust Section for exhaust duct

preparation.

• When installing the oven beneath smooth, flatcabinets, be careful to follow the instructions

on the top cabinet template for power cordclearance.

7


I-]PLACEMENT OF THE MOUNTING PLATE

I_ REMOVING THE OVEN FROMTHE CARTON/REMOVING THEMOUNTING PLATE

_ Remo_e the turntable, installation instructions,

filters, exhaust adaptor; (lampe_; shelf and the

small hardware bag. Do not reillo'_e the St_rofimm

protecting the front of the o_en.

_Fold back all 4 carton flaps full) against cartonsides. Then carefifllx roll the oxen and carton oxer

onto the top side. T'he oxen should be restino, ,., in

the St_ toil)am.

Carton

_Pull the carton up and off the oven.

_The motmting plate is attached to the back of the

oxen. I_einoxe the two screws holding it to the oxen.The plate will be used as the rear wall template andfor motmting the oxen to the wall.

_Set the oxen upright Remoxe and properl) discard

I)lastic bags, and St_roflmm.

[] )ackingOpen the o_en door and relnoxe an} I

material, if present, fi'om inside the oxen.

1-_ FINDING THE WALL STUDS

WallStuds

i

_Find the studs, usino one of the foHo_dn,,

methods:

A. Stud finder - a magnetic device whichlocates nails.

OR

B. Use a hammer to tap lightly across themounting surthce to find a solid sound.This will indicate a stud location.

_ Aiter locating the stud(s), find the center by

probing the wall with a small nail to find theedges of the stud. Then place a mark halt\raybetween the edges, The center of any ac!jacentstuds should be 16" or 24" fl'om this mark.

_Draw a line down the center of the studs.

THE OVEN MUST BE CONNECTED TO AT LEASTONE WALL STUD.

8


DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET

Plate position - beneath flat bottomcabinet

Plate position - beneath framed recessedcabinet bottom

Mounting Plate Tabs! the Cabinet

Bottom

""S,

At least 30", up to 36"

Mounting Plate TabsTouching the Bacl<Frame

\

\

\

!

30" to Cool<top

Plate position - beneath recessed bottomcabinet with front overhang

Mounting Plate withTabs Below CabinetBottom the SameDistance as the Front

Overhang Depth

, II

30"to Cool<top

Your cabinets may have decorative trim that interferes

with the oven installation. Remove the decorative trim

to install the oven properly and to make it level.

THE OVEN MUST BE LEVEL

Use a level to make sure the cabinet bottom is level.

If the cabinets have a fl'ont overhang only, with no

back or side fi'ame, install the mounting plate downthe same distance as the fi'ont overhang depth. This

will keep the oven level.

[]Measure the inside depth of the fi'ont overhang.

[] Draw a horizontal line on the back wall an equaldistance below the cabinet bottom as the inside

depth of the fi'ont overhang.

_For this b'pe of installation with fl'ont overhang only,

align the mounting tabs with this horizontal line, nottouching the cabinet bottom as described in Step D.

9


ALIGNING THE WALL PLATE

\

H_lole iI Draw a Vertical

^ _ LineonWallI<_ fromCenterofi TopCabinetii

HoleC_/' _ _ _ .........................................5 ° ° s_ _s_6 _,__I

,_, ,I,AreaE I

CAUTION: Wear glo_es I

to a_oid cutting fingers on

sharp edges.

[]Draw a vertical line on the wall at the center of the 30"wide space.

_Use the moui_ting plate as the template for the rear

wall. Place the mom_ting plate on the wall, makingsure that the tabs are touching the bottom of thecabinet or the level line drawn in Step C for cabinetswith front overhm_g. Line up the notch mid center lineon the mounting plate to the center line on the wall.

[] X._l_ile holding the mounting plate with one hand,draw drcles on the wall at holes A, B, C and D (see

illustration above/actual plate marked with arrows).Four holes must be used for mounting.

-_------ HoleB

//

//

Hole D

NOTE: Appearance andshape of the motmtingplate may wu'v ti'om vom"model.

NOTE: Holes C and D are inside area E. If neither

C nor D is in a stud, find a stud s()mewhere in area E

and draw a fifth drcle to line up with the stud. It isimportant to use at least one wood screw nlountedfirmly in a stud to sui_port the weight of the oven.

Set the mounting plate aside.

[] Dlill holes on the circles. If there is a stud, chill a :"A(;"hole fin" wood screws. For holes that don't line up witha stud, dlill a %" hole fin" toggle bolts.

NOTE: DO NOT MOUNT THE PLATEAT THIS TIME.

10


INSTALLATION TYPES

This oven is designed h)r adaptation to the fi)llowing three

types of ventilation:

A. Outside Top Exhaust (Vertical Duct)

B. Outside Back Exhaust (Horizontal Duct)

C. Recirculating (Non-Vented Ductless)

(Choose A, B or C)

NOTE: This ()veil is shipped assembled fin" Outside Top

Exhaust (except for non-vented models). Select the type

of ventilation required for vom" installation and proceedto that section.

OUTSIDE TOP EXHAUST(VERTICAL DUCT)

_-] OUTSIDE BACK EXHAUST(HORIZONTAL DUCT)

1

RECIRCULATING(NON-VENTED DUCTLESS)

On models shipped fi)rnon-vented exhaust, a

disposable charcoal filter isincluded with the oven and

needs to be installed to helpreulove si/loke and odors.

On models shipped fi)routside top exhaust, aCharcoal Filter Accessory Kit

is required for the non-ventedexhaust. (See your Owner'sManual fin" the kit nmnber.)

11


OUTSIDE TOP EXHAUST (Vertical Duct)

INSTALLATION OVERVIEW

A1. Attach Mounting Plate to Wall

A2. Prepare Top CabinetA3. Install AdapterA4, Mount Oven

A5. Ac!j ust Exhaust AdaptorA6. Connect Ductwork

I-_ ATTACH THE MOUNTINGPLATE TO THE WALL

Attach the plate to the wall using toggle bolts. At leastone wood screw must be used to attach the plate to awall stud.

[]Remove the toggle wings fl'om the bolts.

[]Insert the bolts into the mounting platethrough the holes designated to go into drwvalland reattach the toggle wings to '_A"onto each bolt.

To use toggle bolts:

Spacingfor TogglesMoreThanWall

+l.-,-[._Thickness

MountingPlate

Bolt End

_ Place the mounting plate against the wall andinsert the toggle wings into the holes in the wall tomount the plate.

NOTE: Betore tightening toggle bolts and woodscre_, make sure the tabs on the mounting platetouch the bottom of the cabinet when pushedflush against the wall and that the plate is properlycentered under the cabinet.

CAUTION: Be careflfl to axoid I)inchin'*_ fingersbetween the back of the mounting plate and the wall.

_ Tighten all bolts. Pull the plate awax from the wallto hel I) tighten the bolts.

12


I-_ USE TOP CABINET TEMPLATEFOR PREPARATION OF TOPCABINET

You need to drill holes for the top sui)port screws, a

hole large, enouoh_ for the power cord to fit through,

and a cutout large enough for the exhaust adaptor.

" Read the instructions on the TOP CABINETTEMPLATE.

" Tape it tmderneath the top cabinet.

" Drill the holes, following the instructions on theTOP CABINET TEMPLATE.

CAUTION: _4ear safety o-oo-des when drillim, holes

in the cabinet bottom.

ASSEMBLE ANDINSTALL ADAPTOR

Damper

-- ExhaustAdaptor

BlowerPlate

BackofOven

NOTE: On some models, the exhaust adaptor and

damper assembly may ah'eadv be assembled to the oven.

_ Place the oven in its ul_right position, with the top

of the trait lacing up.NOTE: Make sure the blower fan blades are visible

and are pointing up.

_ Insert the tabs on each side of the damper into the

holes at the inside rear of the adaptor.

_ Attach the exhaust adaptor to the blower plate with

the two bronze metal screws provided.

Make sure that the damper pivots easily before

mounting oven.

You will need to make a(!iustments to assure proper

alignment with your house exhaust duct after the()veil is installed'.

I-_ MOUNT THE OVEN

FOIl EASIER INSTAI,IATION AND PERSONAl,

SAFETY, WE RECOMMEND THAT TWO PEOPLE

INSTALL THIS OVEN.

IMPORTANT: Do not grip or use handleduring installation.

NOTE: If your cabinet is metal, use the nylon

grommet around the power cord hole to prevent

cutting of the cord,

NOTE: We recommend using filler blocks if the

cabinet fl'ont hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are not

used, case damage may occur from overtightening screws.

NOTE: When mounting the

oven, thread power cord

through hole in bottom

of top cabinet. Kee I) it tight

throughout Steps 1-3.Do not pinch cord or liftoxen by pulling cord.

_I,ifl tilt itoven,fi)rward and hook

slots at back bottom

edge onto two lower

tabs of mounting

plate.

[_ Rotate front of o_en

up against cabinet

bottoI//.

13


MOUNT THE OVEN (continued)

CabinetFront

F/ CabinetBottomShelf

z!/_ FilleI Block

Equivalent

I !! III NLI! /I[IItODepthof CabinetRecess

Self-AligningScrew

OvenTop

[]Attach tile (wen to the top cabinet by inserting

3 sell'aligning screws through outer top cabinetholes. Turn two hill turns on each screw. Be sure

to keep power cord tight. Be caacefnl not to pinchthe cord, especially when mounting flnsh tobottom of cabinet.

[] Tighten tile three screws to tile top of tile oxencompletely. (X._hile tightening screws, hold the

oxen ill place against tile wall and tile top cabinet.)

[]Install filters. See tile Owner s Manualgreasepacked with tile oxen.

ADJUST THE EXHAUSTL_I

ADAPTOR

Open tile top cabinet and a(!iust tile exhaust adaptorto connect to tile house duct.

1

Damper

BackofOven

I-_ CONNECTING DUCTWORK

HouseDuct

-i

[] ExteIld tile hot/se dt/ct dowll to COIlllect to

tile exhaust adaptor.

] . , duct tape.Seal exhaust durt ioints using

14


OUTSIDE BACK EXHAUST IHorJzo.talD.ctl


B1. Prepare Rear _,_allB2. Attach Exhaust Adaptor to

_,_all Plate

B3, Attach Mounting Plateto X,Vdl

B4. Prepare Top CabinetBS. A¢!just BlowerB6. Motmt the Oven

1

PREPARING THE REAR WALLKmmmmmmmmmd

FOR OUTSIDE BACK EXHAUSTYou need to cut an Io )eniw, in the rear wall tot

outside exhaust.

_Read the instructions on the REAR X,VAI,I,

TEMPLATE.

_Tape it to the rear wall, lining up with the holes

pre_iously drilled for holes A and B in the wall

pla re.

_Cut the )enino the instHictions of theI _, followingO

REAR _£M,I, TEMPI,ATE.

ATTACH THE EXHAUSTADAPTOR TO THE OVEN REARPANEL

_ Unscrew and remove the exhaust adaptor

assembly fl'om the top of the oven.

[ _ _ Exhausti ___ Adaptor

_Attach the exhaust adaptor to the oxen rearpanel bx sliding it into the guides at the topcenter of the back of the oxen.

__ DamperExhou t ,o ..

._i_ GuideGuide _ Locking0 Tabs

15

Push in securely tmtil it is in the lower locking tabs.

Take care to assure the damper hinge, is installed so

that it is at the top and that the damper .swin,,s.,. freely.,


ATTACH THE MOUNTINGPLATE TO THE WALL

Attach the plate to the wall using toggle bolts. At leastone wood screw must be used to attach the plate to awall stud.

[] I/emove the toggle wings fi'om the bolts.

[]Insert the bolts into the mounting plate throughthe holes designated to go into dr}svall and reattachthe toggle wings to :_A"onto each bolt.


MountingPlate

Spacingfor TogglesMore-,-I_,-,,-!_,_ ThanWall Thickness

i

ToggleWings

B01tEnd

_ Place the mounting plate against the wall andinsert the toggle wings into the holes in the wallto mount the plate.

NOTE: Betore tightening toggle bolts and woodscre_, make sure the tabs on the mounting platetouch the bottom of the cabinet when pushed flushagainst the wall and that the plate is properlycentered under the cabinet.

CAUTION: Be careflfl to axoid I)inching, finge_between the back of the mounting, I)late and the wall.

_ Tighten all bolts. Pull the from the wallplateto help tighten the bolts.

[=ff_ USE TOP CABINET TEMPLATEFOR PREPARATION OF TOPCABINET

You need to drill holes for the top support screws anda hole large enouoh for the power cord to fit throu ,h

® Read the instructions on the TOP CABINETTEM PI,ATE.

* Tape it underneath the top cabinet.

* Drill the holes, following the instructions on theTOP CABINET TEMPLATE.

CAUTION: \'_Teal"safet) goggles when drilling holes inthe cabinet bottom.

16


ADAPTING BLOWER FOROUTSIDE BACK EXHAUST

[] Renmve the two screws that hold the blower plate

and remove the screw holding the blower motor

to the oven. Slide blower plate fl'om trader its

retaining flange.

Retaining 1_ _

Flange ,_,4k _,___.._.._ Blower Plate

--_

[] Careflflly the blower trait. The wirespull O[lt

will extend far enough to allow you to a(!justthe blower unit.

Back ofOven

_ Rotate blower trait counterclockwise 180 °.

Before Rotation

Back ofOven

After Rotation

Back of

Oven

_Roll the blower trait 90 ° so that tan bladeopenings are facing ot/t the back of theo_, eIl.

Before Rolling --_ After Rolling _

ackof_ " Oven

t o °

Back ofOven

_17

_] Place the 1)lox_er unit back into the opening.

CAUTION: Do not pull or stretch the blower

refit wiring. Make sure the wires axe not pinched.

NOTE: The blower unit exhaust openhlgs should

match exhaust openh_gs on rear of oven.

] Replace the blower plate in the same position

as before and replace the screws for the

blower plate and blower motor.

BlowerPlateScrews

BlowerPlate

.,_ Backof OvenBlowerMotor Screw


MOUNT THE OVEN

FOIl EASIER INSTAI,IATION AND PERSONAI,SAFETY, X.VERECOMMEND THAT TWO PEOPLEINSTALL THIS OVEN.

IMPORTANT: Do not grip or use handleduring installation.NOTE: If vour cabinet is metal, use the nylon

gronmlet around tile power cord hole to preventcutting ot tile cord.

NOTE: We recoumlend using filler blocks if tilecabinet front hangs below tile cabinet bott(nn shelf.

IMPORTANT: If filler blocks are not

used, case damage may occur from overtightening screws.

NOTE: When mountingtile oven, thread powercord through hole illbottonl of top cabinet.Kee I) it tight throughoutSteps 1-3. Do not pinchcord or lifi oven bv

Imllin(*', cord.

[]I,ifl ()veil, ittilt

fin'ward and hookslots at back l)()ttom

edge onto two lowertabs of mounting plate.

\

/_ Rotate front (If oven lip

against cabinet 1)()ttom.

CabinetFront

CabinetBottomShelf

FillerBlock

T quivalent

to Depthof CabinetRecess

Self-AligningScrew

OvenTop

[]Attach tile oven to tile top cabinet by inserting

3 sell=aligning screws through outer top cabinetholes. Turn two fllll ttu'ns on each screw. Be sure

to keep power cord tight. Be careful not to pinchthe cord, especially when mounting flush tobottom of cabinet.

[] Tighten tile three screws to tile top of tile ovenc(mlpletely. (X.Vhile tightening screws, hold theoxen in place against tile wall and tile topcabinet.)

_ Install grease filters. See tile Owner's Manualpacked with tile oxen.

18


RECIRCULATING INon-VentedDuctless)


C1. Attach Mounting Plate to _'all

C2. Prepare Top Cabinet

C3. Adjust Blower

C4. Mount the Oven

C5. Install Charcoal Filter

I-_ ATTACH THE MOUNTINGPLATE TO THE WALL

l

Attach the plate to the wall using toggle bolts. Atleast one wood screw I/ltlSt be used to attach the

plate to a wall stud.

[]Remove the toggle wings fl'om the bolts.

[]Insert the bolts into the mounting plate throughthe holes designated to go into dr xsvall andreattach the toggle wings to :Y," onto each bolt.


Spacingfor TogglesMoreThanWall

-,.-I..-,.-i_,_Thckness

MountingPlate

if,

Bolt End

_ Place the mounting plate against the wall andinsert the toggle wings into the holes in the wall tomount the plate.

NOTE: Betore tightening toggle bolts and woodscre_, make sure the tabs on the mounting platetouch the bottom of the cabinet when pushed flushagainst the wall and that the plate is properlycentered under the cabinet,

CAUTION: Be careflfl to axoid I)inchin<*_ fingers,between the back of the mounting plate and the wall.

_ Tighten all bolts. Pull the plate away fi'om the wallto hel I) tighten the bolts.

| USE TOP CABINET TEMPLATEFOR PREPARATION OF TOPCABINET

You need to drill holes fl)r the top sui)port screws anda hole large enotwh for the power cord to fit throuoh

" Read the instructions on the TOP CABINET

TEMPI,ATE.

" Tape it underneath the top cabinet.

" Drill the holes, fl_llowing the instructions on theTOP CABINET TEMPLATE.

CAUTION: X_'ear safety goggles when drilling holesin the cabinet bottom.

19


ADAPTING BLOWERFOR RECIRCULATION

NOTE: The exhaust adaptor with dmnper is not

needed for recirculating models. Ym may want to

sa',e then/ for possible flmu'e use.

[]Remove and that hold blower andplatesa',e screws

blower trait to the oxen.

Blower Plate Screws

B,owerP,ateBack of Oven

_ Slide the blower plate from trader its retainim,flanoe and lift it off.

letaining

Blower Plate

Careflfllv roll out the blower trait The wires

0 (Y "will extend far en u,,h to allow }(m to a(!lUSt theblower trait.

_Roll the blower rant 30 so that tim blade o )enings

are thcing toward the fi'(mt ()f the oxen.

B011

2O


ADAPTING BLOWER FORRECIRCULATION (continued)

_] Place the blower unit back into the o )ening.l

CAUTION: Do not pull or stretch the blower unitwiring, Make sure the wires are not pinched,

[] Replace blower plate and replace screws for blower

plate and blower motor remoxed in Step 1.

Blower Plate Screws

__ Blower Plate

I Back of Oven

MOUNT THE OVEN

FOIl EASIER INSTAI,I.¢TION AND PERSONAI,

SAFETY, WE RECOMMEND THAT TWO PEOPLE

INSTALL THIS OVEN.

IMPORTANT: Do not grip or use handleduring installation.

NOTE: If yore" cabinet is metal, use the nylon

grommet around the power cord hole to prevent

cutting of the cord.

NOTE: We recommend using filler blocks if the

cabinet front hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are not used,

case damage may occur from over tighteningscrews.

NOTE: When motmting

the oven, thread power

cord through hole in

bottom of top cabinet.

Kee I) it tight throughout

Steps 1-3. Do not pinchcord or lift oven by

mllin , cord

_I,ifl oven, tilt itflwward and hook

slots at back bottom

edge onto two lower

tabs of mounting plate.

/_ Rotate fFont of oxen

up against cabinetbottoln.

CabinetFront

CabinetBottomShelf

Equivalent to Depth

f Cabinet Recess

Self-Aligning Screw

Oven Top

21


MOUNT THE OVEN(continued)

_Attach the oven to the top cabinet by inserting3 self aligning screws through outer top cabinetholes. Turn two fllll ttlI'IIS on each screw. Be sure

to keep power cord tight. Be careful not to pinchthe cord, especially when mounting flush tobottom of cabinet.

[] Tighten the three screws to the top of the oxen

completely. (X_hile tightening screws, holdthe oxen in place against the wall and the topcabinet.)

S /_lnstall filters. See the Owner Manualgrease

packed with the o_en.

INSTALLING THE CHARCOALFILTER

_ Remoxe 2 screws on to ) of grille using aPhillips screwdrix er.

( o_Open the door .)0 .

_ Remoxe the grille.

JJ

Filter

_ ]nsert the filter into the of the )enintop o

between the side support slots,

_CL_

_Push the filter all the wax in where it will rest atan angle,

c S[] Replace the grille and the 2 ,_crews.

_ Close the door.

_j__j

Insertmesh-sideup

22


BEFORE YOU USE YOUR

[_ ake sure the o_en h;Js been installedaccording to instructions.

_3

OVEN

[_ Read the O_ner's Manual.

_ Remove all packing materi_d from the o_en.

_ Repl_lce house fuse or turn breaker back on.

IllIIII

['_ KEEP INS%M,LATION INSTRUCTIONSFOR THE I.OCAI. INSPECTOR'S USE.

% Plug po_,,,er cord into a dedicated 15 to 20 ampelectrical outlet.

Insure proper

23

Printed in (]hina

Installation Abovethe Instructions · PDF fileQuestions? CM1800.GECARES (800.432.2737) ......

Documents

Transcript of Installation Abovethe Instructions · PDF fileQuestions? CM1800.GECARES (800.432.2737) ......