Inroduction to Offshore Structures
description
Transcript of Inroduction to Offshore Structures
5/6/2011
1
Introduction to Analysis of Offshore Structures
OFFSHORE STRUCTURAL ENGINEERINGIntroduction to offshore EngineeringStructural Modeling using SACSLoads on Offshore Structures (Gravity and Environmental)Structural Analyses (in-service & pre-service)y ( p )Design Methods and PrinciplesDesign of Tubular MembersDesign of Tubular JointsDesign of Wide flange Beams / Plate GirdersDesign of Lifting DevicesDesign of buoyancy systemsPile Foundation DesigngPile – Soil InteractionCodes and StandardsCode Provisions (API RP 2A)
5/2/2011 1 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
Introduction to Analysis of Offshore Structures
Session 2nd May 2011 3rd May 2011 4th May 2011 5th May 2011 6th May 2011
Morning Introduction to Offshore
Lift analysis & Lift Point
Ultimate strength of
Pile design and
Float-over installations
OUTLINE
(9 am to 12 noon)
structures design jacket Driveability
Evening
(2 pm to 5 pm)
Tubular member & Joint design
Non-Tubular member and joint Design
Fatigue analysis and design
Jacket stability and MudmatDesign
Finite Element Analysis
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
2
5/6/2011
2
Introduction to Analysis of Offshore Structures
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
3
Introduction to Analysis of Offshore Structures
Hydrocarbon Production and Transportation
Riser
Wel
l Flu
id
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
4
W
Conductors (wells)
Tie-in Spool
5/6/2011
3
Introduction to Analysis of Offshore Structures
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
5
Introduction to Analysis of Offshore Structures
Jackup DrillingMovable Drill Floor
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
6
5/6/2011
4
Introduction to Analysis of Offshore StructuresSEMI-SUBMERSIBLE RIG (COURTESY OF STENA DRILLING)
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
7
Introduction to Analysis of Offshore StructuresDRILL SHIP ‘TRANSOCEAN ENTERPRISE’
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
8
5/6/2011
5
Introduction to Analysis of Offshore StructuresTENDER ASSISTED DRILLING
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
9
Introduction to Analysis of Offshore Structures
Drilling MastJACKEUP PRE-DRILLING
DECK DECK
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
10
PRE-DRILLING OF WELLS JACKEP DRILLI MAST STOWED BACK
5/6/2011
6
Introduction to Analysis of Offshore Structures
DRILL MASTJACKEUP DRILLING AFTER PLATFORM INSTALLATION
JACKUP LEG
DRILL FLOOR
DECK
Wellhead Platform
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
11
WELL CENTRES
SPUD CAN
Introduction to Analysis of Offshore Structures
Deck Mounted Drilling Rig
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
12
5/6/2011
7
Introduction to Analysis of Offshore Structures
Drill Floor
Drill Mast
Drill
Setback
Hook LoadDRILL LOADS
Living Quarter
Drill Floor
Drill Support Module
Drill Pipes
Moving
Skid Beam
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
13
Introduction to Analysis of Offshore Structures
Wellhead and Process, Living platforms separated by a distance
Wellhead, Process, Living facilities in a single platforms
As we move away from shallow water depth, the safety in design revolves around economy and new technology
platforms separated by a distance a single platforms
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
14
5/6/2011
8
Introduction to Analysis of Offshore Structures
HOSTILE ENVIRONMENT
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
15
Introduction to Analysis of Offshore Structures
Twister
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
16
5/6/2011
9
Introduction to Analysis of Offshore Structures
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
17
Introduction to Analysis of Offshore Structures
Fixed PlatformsWellhead Platforms
Generally 4 legged or Tripods (3 legged)Supports minimum topsideSupports Well conductors sizes ranging from 16” to 30”Supports Well conductors sizes ranging from 16 to 30In Persian Gulf, typical water depths around 30-70m, most jacket installed by lifting with weight ranging from 600T to 2000 T
Process PlatformsGenerally 8 legged or 6 leggedLarge topsides either installed by modular lifts or float-overLarge 8 legged Jackets weight vary from 4000T to 6000 T
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
18
Large 8 legged Jackets weight vary from 4000T to 6000 T depending on water depthSouth China Sea water depth ranging from 90m to 120m
5/6/2011
10
Introduction to Analysis of Offshore Structures
Wellhead platforms
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
19
Introduction to Analysis of Offshore StructuresProcess platforms
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
20
5/6/2011
11
Introduction to Analysis of Offshore Structures
ANODES BOUYANCY TANKSBouyancy Tank Pile Guide
Skirt Sleeve
Anode
Mudmat
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
21
Introduction to Analysis of Offshore Structures
Bouyancy Tanks
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
22
5/6/2011
12
Introduction to Analysis of Offshore Structures
SHEAR PLATE / YOKE PLATE CONNECTION
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
23
Introduction to Analysis of Offshore Structures
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
24
5/6/2011
13
Introduction to Analysis of Offshore Structures
INPLACE ANALYSIS - PURPOSEStructural analysis to simulate the behaviour of structure as close as possible and to obtain the response to all loads during its SERVICEp gTo check the global integrity of the structure against premature failureTo check the components (members and joints) against the loads that they are carrying and transmitting to the foundationTo satisfy code requirements against safety
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
25
To satisfy code requirements against safety of structure and supporting foundationCalled Inservice analaysis or Inplace Analysis
Introduction to Analysis of Offshore Structures
Design for In-Service LoadsIn-service analyses
In-place AnalysisDynamic AnalysisDynamic AnalysisFatigue AnalysisSeismic AnalysisShip Impact Analysis
In-service LoadsGravity LoadsE i t l L d
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
26
Environmental LoadsSeismic LoadsAccidental Loads
5/6/2011
14
Introduction to Analysis of Offshore StructuresINPLACE ANALYSIS
Jacket GeometryMember SizesWave DirectionsHydrodynamic CoefficientsBasic Loads and CombinationsPile-Soil Model (P-Y, T-Z and Q-Z Curves)Analysis MethodsDynamic EffectsPile capacity and Factor Of Safety
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
27
p y yMembers and Joint DesignAllowable Stress Modifiers
Introduction to Analysis of Offshore Structures
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
28
5/6/2011
15
Introduction to Analysis of Offshore Structures
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
29
Bottom line : Fabrication and Installation plays a major role !
Introduction to Analysis of Offshore Structures
Design for Pre-Service LoadsPre-service analyses
Load-out AnalysisSea Transportation AnalysisLifting AnalysisLaunch AnalysisUpending AnalysisOn-bottom AnalysisPile Driveability Analysis
Pre-service Appurtenance DesignLif i P d / d b
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
30
Lifting Pad-eye / spreader barLaunch CradleBuoyancy TanksMud-mat
5/6/2011
16
Introduction to Analysis of Offshore Structures
LOGICAL SEQUENCE
FABRICATIONLOADOUTSEA TRANSPORTATIONLIFTINGLAUNCHINGFLOATATIONUPENDINGON-BOTTOM STABILITYPILE DRIVINGPILE GROUTING
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
31
PILE GROUTINGDECK INSTALLATIONCOMMISSIONINGSTARTUP
Introduction to Analysis of Offshore Structures
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
32
5/6/2011
17
Introduction to Analysis of Offshore Structures
LOADOUT METHODS
LIFTED LOADOUT – For small jacket and decks, where crane either land based or floating is available with adequate capacity, loadout can be done by lifting and placing it on the cargo barge.
SKIDDED LOADOUT – For larger jackets and decks of several SKIDDED LOADOUT – For larger jackets and decks, of several thousand tonnes weight, usually skidded loadout is employed to avoid large capacity cranes. The jacket or deck will be mounted on a temporary skid support either continuous or discrete and will be pulled on to the barge using winches.
TRAILER LOADOUT – Recent times, the trailer loadout is getting more popular due to its robustness and quick preparatory time. Trailers are multi-axle load balancing wheels with appropriate spreader girders on top. The jacket or deck will be moved from quayside on to the barge using these trailers and they will be
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
33
q y g g yremoved.
Introduction to Analysis of Offshore Structures
Barge
Barge Ballasted too much
No SupportA
g
Barge
Barge not enough ballast during rising tide
B
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
34
Barge
5/6/2011
18
Introduction to Analysis of Offshore Structures
Barge
Ballast Pump Failures during rising tide
No SupportC
D
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
35
Barge
Introduction to Analysis of Offshore Structures
Loadout of Launch Jacket
Mooring LineBollard
WinchPivot andPull Wires
Jacket
FenderPivot and pulley
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
36
Yard
Loadout DirectionSkid Rails
5/6/2011
19
Introduction to Analysis of Offshore Structures
LOADOUT OF LAUNCH JACKET
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
37
Launch Barge
Introduction to Analysis of Offshore Structures
DECK TRAILER LOADOUTTemporary Brace
COG
TrailerTemporary S
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
38
TrailerSupport
5/6/2011
20
Introduction to Analysis of Offshore Structures
DECK TRAILER LOADOUTTemporary Brace
COG
TrailerTemporary Support
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
39
Support
Introduction to Analysis of Offshore Structures
DECK SUPPORTED ON LOADOUT BEAM AND TRAILER
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
40
5/6/2011
21
Introduction to Analysis of Offshore Structures
DECK SUPPORTED ON LOADOUT BEAM AND TRAILER
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
41
Introduction to Analysis of Offshore Structures
TRAILER CARRYING A DECK MODULE
Trailer
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
42
5/6/2011
22
Introduction to Analysis of Offshore Structures
TYPICAL TRAILER
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
43
Introduction to Analysis of Offshore Structures
DECK ON LOADOUT BEAM AND TRAILER ON BARGE
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
44
5/6/2011
23
Introduction to Analysis of Offshore Structures
LOADOUT BEAM AND TRAILER IS BEING REMOVED
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
45
Introduction to Analysis of Offshore Structures
JACKET TRAILER LOADOUT
TRAILERS
CARGO BARGEFABRICATION YARD QUAY SIDE
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
46
YARD QUAY SIDE
5/6/2011
24
Introduction to Analysis of Offshore Structures
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
47
Introduction to Analysis of Offshore Structures
TRANSPORTATION METHODS
DRY TOW – The transportation method adopted for most offshore structures are using dump barges and tugs are normally used for towing. Usually tugs will move at a speed of around 6 knots (Approx 3 m/sec).
WET TOW – For faster transportation, self propelled vessels can be used such as conventional ship shape vessels and semi-submersible type carriers. Usually used for trans-continental tow. The speeds can reach as much as 10 to 12 knots. Reduce transportation time by half thus reducing the risk along the route.
SELF TOW – Large jackets, gravity platform structures, spare type structures some times self towed to the site using
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
48
spare type structures some times self towed to the site using tugs. Special care needs to taken for such transportation arrangements.
5/6/2011
25
Introduction to Analysis of Offshore Structures
TYPICAL TRANSPORTATION ROUTE
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
49
Introduction to Analysis of Offshore Structures
JACKET READY FOR TOW
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
50
5/6/2011
26
Introduction to Analysis of Offshore Structures
DECKS BEING TOWED
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
51
Introduction to Analysis of Offshore Structures
DESIGN ENVIRONMENTAL CONDITIONS
Most Severe environmental conditions during the tow period along the routeDesign environmental conditions include Design environmental conditions include design wave, wind and current10 year return period monthly extremes shall be used as design environmental conditions (Tow period more than 30 days)For smaller tow period, lesser design return
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
52
For smaller tow period, lesser design return period may be accepted
5/6/2011
27
Introduction to Analysis of Offshore Structures
TYPICAL CARGO BARGE
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
53
Introduction to Analysis of Offshore Structures
Tow Bridle
Tow Arrangement
Barge Tug
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
54
5/6/2011
28
Introduction to Analysis of Offshore Structures
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
55
Introduction to Analysis of Offshore Structures
MOTION PARAMETER DEFINITION
Bow
1. Heave
2. Sway
3. Surge
4. Yaw
Stern
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
56
5. Pitch
6. Roll
5/6/2011
29
Introduction to Analysis of Offshore Structures
TYPICAL BARGE MOTION PARAMETERS
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
57
Source : NDI/30
Introduction to Analysis of Offshore Structures
Jacket on Cargo Barge
Seafastening
Barge
Jacket
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
58
5/6/2011
30
Introduction to Analysis of Offshore Structures
Jacket on Cargo Barge
Jacket
ROLL
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
59
Introduction to Analysis of Offshore Structures
Z
F= ma
MSL X
PITCH
r
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
60
MSL X
Centre of Rotation (COR)
5/6/2011
31
Introduction to Analysis of Offshore Structures
Barge DraftBarge draft shall be calculated based on the ballast and cargo weight. Usually, it shall be approximately 0.55D where D is the moulded depth of the barge.
In any case following minimum draft shall be used
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
61
Source : NDI/30
Introduction to Analysis of Offshore Structures
Acceleration and Inertial ForceAngular Acceleration
2
2
2
secdeg/in 4T
Qa π=
TWhere
Q = Roll or pitch angle in deg
T = Roll or pitch period in sec
Inertial ForceInertial Force F=m.a.r.
Wh
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
62
Where m = mass of the elementa = angular accelerationr = distance of element from centre of rotation
5/6/2011
32
Introduction to Analysis of Offshore Structures
Cargo
Roll W Sin(θ)
BARGE
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
63
θ W Cos(θ)
Introduction to Analysis of Offshore Structures
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
64
5/6/2011
33
Introduction to Analysis of Offshore Structures
LIFT METHODS
SINGLE CRANE – Generally single crane lift is adopted for all cases depending on the capacity. Examples of this type of lift is jacket or deck lift in offshore. Most of the vessels in asian region fitted with cranes in the range of 1000 Tonnes to 3500 TonnesTonnes.
DUAL CRANE – For larger jackets, some times dual crane lift is used. Typically Heerama vessel is fitted with dual cranes and can be used for lifts as much as 16,000 Tonnes.
MULTIPLE CRANES – Multiple crane lifts are notmally not used in offshore operation due to problem associated with control and is used in jacket upending in the yard. Some time also used for upending jacket panels and lifting deck panels
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
65
also used for upending jacket panels and lifting deck panels.
Introduction to Analysis of Offshore Structures
DETERMINATE LIFT
A sling arrangement is made such that the system is statically determinate.Sli l d b l l t d i Sling loads can be calculated using equilibrium equations.Sling Mismatch or elasticity of slings does not significantly change the sling load distribution.Most offshore lifts we use this to avoid
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
66
Most offshore lifts, we use this to avoid exact sling length calculations.
5/6/2011
34
Introduction to Analysis of Offshore Structures
INDETERMINATE LIFT
A sling arrangement is made such that the system is statically indeterminate.Sling loads can not be calculated using equilibrium equations.Typical cases will be lift points at different levels, lifts using matched slings.
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
67
s gs
Introduction to Analysis of Offshore Structures
Auxialiary HookMain Hook
Boom
Jacket
Sling
Crane Vessel
Crane Engine
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
68
Cargo Barge
5/6/2011
35
Introduction to Analysis of Offshore Structures
JACKET LIFTED OFF THE BARGE
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
69
Introduction to Analysis of Offshore Structures
DECK LIFTED OFF THE BARGE
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
70
5/6/2011
36
Introduction to Analysis of Offshore Structures
DESIGN CONDITIONSThe Crane barge has its own motion characteristics depending on the design.Design environmental conditions to allow the glifting shall be selected to allow the operation of the vessel, and the craneLarge the seastate, the motions will be large leading to additional forces on the barge/crane/structure system.Hence a suitable seastate shall be selected dpending on the specific project and in
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
71
dpending on the specific project and in general, the seastate shall be in the order of 0.5m to 1m wave height with a wind speed not exceeding 20 m/sec.
Introduction to Analysis of Offshore Structures
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
72
5/6/2011
37
Introduction to Analysis of Offshore Structures
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
73
Introduction to Analysis of Offshore Structures
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
74
5/6/2011
38
Introduction to Analysis of Offshore Structures
MOTION OF CRANE VESSEL
Bow
1. Heave
2. Sway
3. Surge
4. Yaw
Stern
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
75
5. Pitch
6. Roll
Introduction to Analysis of Offshore Structures
MULTI-BODY DYNAMICSCrane Boom StiffnessSling
Stiffness
Cargo
Crane Vessel Movement
Barge Movement
Fender
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
76
5/6/2011
39
Introduction to Analysis of Offshore Structures
Ks Kb - Bending Stiffness
SPRING-MASS SYSTEM
K
s Kb Bending Stiffness
K b
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
77
KwvKwb
Introduction to Analysis of Offshore Structures
DYNAMICS OF CRANE BARGE / CARGO SYSTEM
As the crane vessel is in floating condition, the environmental loads will change the position by roll/pitch and heave motionroll/pitch and heave motion.These motion induces inertia loads on the structure hanging from the crane hook.The effect of Cargo/Crane Boom/Vessel dynamics needs to be studied using suitable model and arrive at the dynamic forces induced
th t
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
78
on the system.
5/6/2011
40
Introduction to Analysis of Offshore Structures
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
79
Introduction to Analysis of Offshore Structures
WHAT IS THE PURPOSE OF LAUNCH ANALYSIS ?
To determine the suitable launch parameters such as barge trim, friction coefficient, required to successfully launch the jacketTo determine the worst case dive depth to make sure the jacket does not touch the seabedTo determine the amount of bouyancy required during launch to avoid undue resultsTo determine the stability of the jacket during the process of diving such, GM, roll and pitch etc.To determine the stresses induced during various phases of motion during launch
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
80
5/6/2011
41
Introduction to Analysis of Offshore Structures
TYPICAL LAUNCH BARGE
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
81
Introduction to Analysis of Offshore Structures
Launch Rail
LAUNCH RAIL AND ROCKER ARMSRocker Arm
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
82
5/6/2011
42
Introduction to Analysis of Offshore Structures
JACKET LAUNCH
Jacket is launched from the launch barge as an alternative to lift. Jacket l h h d f l i h j k i launch method of placing the jacket is suitable for large jacket as the lift capacity of cranes are limited.Jacket will be allowed to slide from the barge into water by means of a push or
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
83
by simply trimming the barge
Introduction to Analysis of Offshore Structures
JACKET LAUNCH ANALYSIS
LAUNCH SIMULATION : Launch analysis is performed to simulate the rigid body motion of the jacket on barge, rocker arm and plunge in to water During various phases of plunge in to water. During various phases of movement, jacket stability, rocker arm reaction and hydrodynamic loads on jacket are simulated.
POST LAUNCH ANALYSIS : During the launch phases, critical phase will be selected
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
84
p , pand a structural analysis will be carried out to simulate the stresses induced during launch.
5/6/2011
43
Introduction to Analysis of Offshore Structures
LAUNCH PARAMETERS
Barge Trim – The barge trim will depend on the weight of jacket, friction between the barge and jacket. Generally the trim will be around 2 to 4 degrees. The trim will be achieved by suitably ballasting the barge.
Friction – The launch cradle friction with the barge rails will determine whether the jacket will be able to slide on its own weight or require a push. The friction coefficient can be reduced by suitable lubrication of the surfaces.
Winch Speed : Normally a winch speed of 0.6m sec is used.
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
85
Bouyancy – Bouyancy will play a major role in launch of the jacket. A minimum reserve bouyancy of 15% is required
Introduction to Analysis of Offshore Structures
Preparation for LaunchBarge will be arriving at the location of installation and a preset distance of 500m away from the final location of installation, y ,the launch will performed.Barge will be suitably ballasted to achieve a trim angle of 2 to 3 degrees.Seafastening will be cut after obtaining clearance from Marine Warranty Surveyor with regard to weather window and
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
86
gacceptable sea-state for launching.
5/6/2011
44
Introduction to Analysis of Offshore Structures
BARGE TRIM
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
87
Forward DraftTrim Angle
Introduction to Analysis of Offshore Structures
LAUNCH DURATIONAfter cutting the sea-fastening, jacket will move forward towards the rocker arm. If the jacket does not move artificial push If the jacket does not move, artificial push using strand jack or winch shall be applied to overcome the initial static friction.Once the jacket starts to move, generally the launch duration shall not take more than 2 to 3 minutes
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
88
5/6/2011
45
Introduction to Analysis of Offshore Structures
JACKET LAUNCH TRAJECTORY
Final Floating
Phase 1 to 3Phase 4
Phase 5Push
Barge
Floating Position
Phase 5
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
89
Seabed Clearance
Introduction to Analysis of Offshore Structures
Design for Pre-Service Loads(A jacket After Launch)
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
90
5/6/2011
46
Introduction to Analysis of Offshore Structures
LAUNCH RAIL AND ROCKER ARM
Rocker ArmRocker Arm
Launch Rail
Jacket
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
91
Barge
Introduction to Analysis of Offshore Structures
JACKET ON ROCKER ARM
JACKET COG
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
92
Supports on Rocker Arm
5/6/2011
47
Introduction to Analysis of Offshore Structures
POST LAUNCH : JACKET TIPPING
Jacket weight
Supports on Rocker arm
weight
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
93
Water Spring Supports
Introduction to Analysis of Offshore Structures
PitchRigging Platform for upending rigging
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
94
COG
Pitch of 1-2 Degrees is acceptable. The rigging platforms shall be above water and allow the rigger to access during operational waves.
5/6/2011
48
Introduction to Analysis of Offshore Structures
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
95
Introduction to Analysis of Offshore Structures
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
96
Punch through effect
5/6/2011
49
Introduction to Analysis of Offshore Structures
JACKET UPENDING IN WATER
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
97
Introduction to Analysis of Offshore Structures
JACKET UPENDING IN AIR
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
98
5/6/2011
50
Introduction to Analysis of Offshore StructuresJACKET UPENDING IN WATER
1 32
654
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
99
Introduction to Analysis of Offshore Structures
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
100
5/6/2011
51
Introduction to Analysis of Offshore Structures
ANALYSIS METHODS
Linear Static AnalysisLinear Static Analysis (Pseudo-Static)Linear Static Analysis (Pseudo-Static)Dynamic Wave Response Analysis (Frequency Domain)Dynamic Wave Response Analysis (Time Domain)Nonlinear Analyses (material or geometric)
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
101
Introduction to Analysis of Offshore Structures
Structural Response – Static AnalysisIf the natural period of the platform is considerably away from fatigue waves, assumption of equivalent static analysis is assumption of equivalent static analysis is acceptableSimple calculations for DAF using SDOF model for each of the wave period can be calculated and applied to the wave loadsSimple Static Analysis either with Pile Soil Interaction or equivalent linearised
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
102
}*{}]{[ DAFFXK =
Interaction or equivalent linearised foundation can be used.
5/6/2011
52
Introduction to Analysis of Offshore Structures
DYNAMIC AMPLIFICATION FACTOR (SDOF)
22
1DAFT T
=⎛ ⎞ ⎛ ⎞2
21 2N n
T TT T
ς⎛ ⎞ ⎛ ⎞− +⎜ ⎟ ⎜ ⎟⎝ ⎠ ⎝ ⎠
TN – Natural Period of the structure
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
103
T – Wave Period
ζ – Structural Damping Ratio
Introduction to Analysis of Offshore Structures
8
9
10
Damping = 5%
Damping = 0.1%
DYNAMIC AMPLIFICATION FACTOR (DAF)
2
3
4
5
6
7
Damping = 100%
Damping = 50%
Damping = 15%
DA
F
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
104
0
1
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5
Frequency Ratio β β = TN / T
5/6/2011
53
Introduction to Analysis of Offshore Structures
Structural Response – Wave Response analysisIf the natural period of the platform is close to the fatigue waves, assumption of equivalent static analysis is not acceptableSimple calculations for DAF using SDOF model for will result in very conservative or non-conservative results depending on the assumptions made on average wave periods for the calculation of DAFHence a Dynamic Wave Response analysis
d t b f d
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
105
needs to be performedDue to iterative calculations in Free Vibration analysis, equivalent linearised Foundation is required
Introduction to Analysis of Offshore Structures
Structural Response – Wave Response analysis
The dynamic wave response analysis requires the dynamic characteristics
0}"]{[}]{[ =+ XMXK
The results of dynamic analysis will be used in Dynamic Wave Response analysis to generate structure response
Free Vibration Analysis
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
106
}{}"]{[}']{[}]{[ FXMXCXK =++
Wave Response Analysis
5/6/2011
54
Introduction to Analysis of Offshore Structures
Structural Response – Static AnalysisIf the natural period of the platform is considerably away from fatigue waves, assumption of equivalent static analysis is assumption of equivalent static analysis is acceptableSimple calculations for DAF using SDOF model for each of the wave period can be calculated and applied to the wave loadsSimple Static Analysis either with Pile Soil Interaction or equivalent linearised
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
107
}*{}]{[ DAFFXK =
Interaction or equivalent linearised foundation can be used.
Introduction to Analysis of Offshore Structures
DYNAMIC AMPLIFICATION FACTOR (SDOF)
22
1DAFT T
=⎛ ⎞ ⎛ ⎞2
21 2N n
T TT T
ς⎛ ⎞ ⎛ ⎞− +⎜ ⎟ ⎜ ⎟⎝ ⎠ ⎝ ⎠
TN – Natural Period of the structure
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
108
T – Wave Period
ζ – Structural Damping Ratio
5/6/2011
55
Introduction to Analysis of Offshore Structures
8
9
10
Damping = 5%
Damping = 0.1%
DYNAMIC AMPLIFICATION FACTOR (DAF)
2
3
4
5
6
7
Damping = 100%
Damping = 50%
Damping = 15%
DA
F
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
109
0
1
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5
Frequency Ratio β β = TN / T
Introduction to Analysis of Offshore StructuresStructural Response – Wave Response analysis
If the natural period of the platform is close to the fatigue waves, assumption of equivalent static analysis is not acceptableSi l l l ti f DAF i SDOF d l Simple calculations for DAF using SDOF model for will result in very conservative or non-conservative results depending on the assumptions made on average wave periods for the calculation of DAFHence a Dynamic Wave Response analysis needs to be performed
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
110
needs to be performedDue to iterative calculations in Free Vibration analysis, equivalent linearised Foundation is required
5/6/2011
56
Introduction to Analysis of Offshore Structures
Structural Response – Wave Response analysis
The dynamic wave response analysis requires the dynamic characteristics
0}"]{[}]{[ =+ XMXK
The results of dynamic analysis will be used in Dynamic Wave Response analysis to generate structure response
Free Vibration Analysis
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
111
}{}"]{[}']{[}]{[ FXMXCXK =++
Wave Response Analysis
Introduction to Analysis of Offshore Structures
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
112
5/6/2011
57
Introduction to Analysis of Offshore Structures
DESIGN PHILOSOPHIES
Working Stress Design (WSD or ASD)Limit State Design (LSD)
Load and Resistance Factor Design (LRFD)Plastic Design (PD)
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
113
Introduction to Analysis of Offshore Structures
DESIGN PHILOSOPHY
≤Demand Capacity
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
114
≤Demand Capacity
5/6/2011
58
Introduction to Analysis of Offshore Structures
Working Stress Design (WSD) or Allowable Stress Design (ASD)
• Service loads are calculated as expected in service• Linear elastic analyses are performed• Allowable stress = Material Strength/Factor of Safety• A design is satisfied if the
Maximum stress < Allowable stress• Limitations
• No 100% sure the load effects will not exceed strengthC ifi t th t th d i ll
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
115
• Case specific, no guarantee that the design covers all cases• Arbitrary choice of Safety Factor?!
Introduction to Analysis of Offshore Structures
STRESS-STRAIN CURVE FOR STEEL
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
116
5/6/2011
59
Introduction to Analysis of Offshore Structures
What is meant by Factor of Safety?
1956-1966: ASCE Task Committee on FOS in their final report indicated that
“The committee has not been successful in its effort to resolve the ‘factor of safety’ question, it is the belief…that the probability approach deserves considerably more study than it has received”
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
117
Introduction to Analysis of Offshore Structures
ALLOWABLE STRESS DESIGN
ASD: Applied stress ≤ Allowable stress
Theoretical
Tested Material
Margin applied to Material stress
≤
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
118
EstimatedLoads
Design Loads
Adjusted Resistance
Material Strength
Design Values
5/6/2011
60
Introduction to Analysis of Offshore Structures
Design ProcedureDesign Load stresses calculated for each effect and combined appropriately
CompressionTensionBendingShearTorsionHoop
Allowable Stresses taken as as fraction (factor of safety) of yield including the geometric effect such as slenderness, local and global buckling torsional buckling etc
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
119
and global buckling, torsional buckling etc.Design state defined for the worst combined case and a decision made based on design load stresses and allowable stresses
Introduction to Analysis of Offshore Structures
Design LoadsDesign Loads taken as maximum occurring during the life. No variability or probability of accidence includedAt times suitable value is taken from historical data and At times, suitable value is taken from historical data and may reflect true loads during life time
Allowable StressesDesign Yield strength assumed to be a constantFactor of Safety is chosen for each load effect. Allowable stress is taken as a fraction of yield strength with
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
120
y gassumed Factor of Safety
5/6/2011
61
Introduction to Analysis of Offshore Structures
Plastic Design
• Service loads are factored by a “load factor”• The structure is assumed to fail under these
loads with plastic hinges formedloads with plastic hinges formed• The cross section is designed to resist the
plastic analysis• Members are safe as they will only be subjected to service loads
• Limitations Preclude other stability fatigue etc limit states
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
121
• Preclude other stability, fatigue etc. limit states• Neglecting the uncertainty in material strength• Arbitrary choice of total factor?!
Introduction to Analysis of Offshore Structures
Limit States Design
• Limit states is a condition at which a structureor some part of that structure ceases to perform its intended function
• Functional requirements• Max. deflections, drift, vibration, permanent deformation
• Could be conceptual• Plastic hinge or mechanism formation
F i bili k
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
122
• Fracture or instability, cracks
5/6/2011
62
Introduction to Analysis of Offshore Structures
Limit States of Strength
• Safety against extreme loads during theintended life of the structure
• Based on safety or load-carrying capacity• Plastic strength, buckling, fracture, fatigueoverturning
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
123
Introduction to Analysis of Offshore Structures
Load and Resistance Factor Design (LRFD)
• LRFD is based on the limit state philosophy• Service loads are multiplied by load factors• Service loads are multiplied by load factors( γ ) and linear elastic analysis is performed
• Materials strength is reduced by multiplyingthe nominal material strength by a resistancefactor (φ)
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
124
5/6/2011
63
Introduction to Analysis of Offshore Structures
Focus on Strength Checking in Design Codes
• Limit states of life, limb and property of humanbeings
• Public Safety of life, limb and property of human beings• Not matters of individual judgments
• Limit states of serviceability
• Usually permit more exercise of judgment on the part of designers
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
125
Introduction to Analysis of Offshore Structures
Basis of LRFD Specification
• Probabilistic models of loads and resistance• Calibration of LRFD criteria to the established ASDCalibration of LRFD criteria to the established ASD
specification for selected members• The evaluation of the resulting criteria by judgment
and past experience aided by comparative design office studies of representative structures
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
126
5/6/2011
64
Introduction to Analysis of Offshore Structures
Safety in LRFD
• Appraise the safety of a structure in terms ofmeasurable probability
• Keep probability of (ultimate strength) failure• Keep probability of (ultimate strength) failuresufficiently and predictably small
• Statistical protection against failure• In statistical terms – probability of failure, orconversely, survival
• Factored (ultimate) loads • Resistance based on characteristic extreme values (e g 5th percentile)
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
127
values (e.g., 5t percentile)
Introduction to Analysis of Offshore Structures
LRFD Checking Equation
RQ φγ ≤∑5/2/2011 Dr. S. Nallayarasu
Department of Ocean EngineeringIndian Institute of Technology Madras-36
128
nii RQ φγ ≤∑Partially Safety Factors
5/6/2011
65
Introduction to Analysis of Offshore Structures
Serviceability in LRFD
• Appraise the structure in terms of itseveryday usefulness
• protect against “non-performance” (buildingfunctionality, occupant comfort, human perception)
• may tolerate higher ‘failure’ probability than for safety
• Real world measurable behavior
• Unfactored (service-level) loads
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
129
( )• Mean value of resistance
Introduction to Analysis of Offshore Structures
Design Rule
nii RQ φγ ≤∑∑• Where Rn is the nominal strength and Qi isthe load effect
• Advantages • Non-case specific, statistical calculations guarantee population behaviorU if f t f f t b th l d d t i l
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
130
• Uniform factor of safety as both load and materialfactors are tied by reliability analysis
5/6/2011
66
Introduction to Analysis of Offshore Structures
Load and Resistance Factors
• Partial safety factors depend on load andstrength statisticsg
• Load factors to account for• variability (uncertainty) in loads
• Resistance factors to account for• Geometry and material property variability• Imperfections in analysis theory• Consequence of failure
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
131
Introduction to Analysis of Offshore Structures
LRFD Factored Load ≤ Factored Strength
Resistance Factor
LRFD METHOD OF DESIGN
FactoredDesign
Tested Material≤Factored
Load Factor
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
132
EstimatedLoads
Design Loads
DesignResistance
Material Strength
Design Values
≤
5/6/2011
67
Introduction to Analysis of Offshore Structures
Load Combinations
• When several loads act in combination with the dead load, only one of these takes on its maximumlifetime value while the other is at its “expected”lifetime value, while the other is at its expectedvalues.
• E.g. Load Cases• 1.2D + 1.6L• 1.2D + 0.5L + 1.6W
Max. life timeWind load
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
133
Introduction to Analysis of Offshore Structures
Limit States in OffshoreStructure Design
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
134
5/6/2011
68
Introduction to Analysis of Offshore Structures
Limit States
• ULS – Ultimate Limit States• Ultimate strength behavior
• FLS – Fatigue Limit States• Fatigue and fracture behavior
• SLS – Serviceability Limit States• Displacements and deflections
• ALS – Accidental Limit States• Collision fire blast dropped object etc
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
135
• Collision, fire, blast, dropped object, etc
Introduction to Analysis of Offshore Structures
Partial Safety Factors
• Dead Load: 1.0 – 1.2• Variable Load: 1.3 – 1.4Variable Load: 1.3 1.4• Environmental load: 1.3 – 1.4• The material partial safety factors vary with
material type
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
136
5/6/2011
69
Introduction to Analysis of Offshore Structures
Ultimate Limit States Design
• ULS-A reflecting extreme permanent loads with regular environmental conditions
• ULS-B reflecting large permanent loads with extreme environmental conditions
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
137
Introduction to Analysis of Offshore Structures
API RP2A WSDAPI RP2A –WSD(20th ed. 1993 21st ed. 2000)
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
138
5/6/2011
70
Introduction to Analysis of Offshore Structures
Sections in API RP2A - WSD1. Planning 2. Design Criteria and
procedures
10. Welding11. Fabrication12. Installation
3. Structural Steel Design4. Connections5. Fatigue6. Foundation Design7. Other Structural
Components and Systems8 M t i l
13. Inspection 14. Surveys15. Reuse16. Minimum Structures17. Assessment of Existing
Platforms (21st ed)
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
139
8. Materials9. Drawings and
Specifications
18. Commentary
Introduction to Analysis of Offshore Structures
Design Loading Conditions in API RP2A - WSD
• To produce the most sever effects• Operating environmental conditions combined with deadOperating environmental conditions combined with dead
loads and max/min live loads appropriate to normal operations (typical 1-year to 5-year storm).
• Design environmental conditions combined with dead loads and max/min live loads for combing with extremeconditions (typical 50-year or 100-year storm)
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
140
5/6/2011
71
Introduction to Analysis of Offshore Structures
Allowable Stress in API RP2A - WSD
• As specified in AISC ASD specificationAs specified in AISC ASD specification• Where stresses are due in part to the lateral and
vertical forces imposed by design environmental conditions, the basis AISC allowable stresses may be increased by one -third
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
141
1/3
Introduction to Analysis of Offshore Structures
One-third Increase inAllowable Stresses, why?
• Can sustain higher load for a short durationCan sustain higher load for a short duration• Unlikely to have all the transient load acting
simultaneously • Willing to take high risk• Agree better with LRFD
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
142
5/6/2011
72
Introduction to Analysis of Offshore Structures
Section 2.3.6 Earthquake
In the calculation of member stresses, the stresses due to earthquake induced loading should bedue to earthquake induced loading should be combined with those due to gravity, hydroelastic pressure and buoyancy.For strength requirements, the basic AISC allowable stress and those presented in Section 3.2 may be increased by 70 percent.Permit minor yielding but no significant damage to
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
143
y g g goccur
Introduction to Analysis of Offshore Structures
Lifting
• Dynamic load factorsOpen sea: 2.0 for main members, 1.35 for others
Sheltered: 1.5 for main members, 1.15 for others
• The AISC increase in allowable stresses for short-term loads should NOT be used.
• Safety factor for slings: 4.0
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
144
• Safety factor for shackles: 3.0
5/6/2011
73
Introduction to Analysis of Offshore Structures
Allowable Stresses for Cylindrical Members
Loading Type Allowable Stress
Axial tension 0.60 Fy
Axial compression <0.60 Fy
Bending <0.75 Fy
Shear 0.4 Fy
Hoop buckling SF = 2.0
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
145
Hoop buckling SF 2.0
Connections SF = 1.7
Introduction to Analysis of Offshore Structures
API RP2A – LRFD (1st ed. 1993)
(Also BS EN ISO 13819)
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
146
5/6/2011
74
Introduction to Analysis of Offshore Structures
Sections in API RP2A - LRFD
A. Planning B. Design RequirementC L d
J. Drawings and Specifications welding
C. LoadsD. Cylindrical Member DesignE. ConnectionsF. FatigueG. Foundation DesignH. Structural Components
and Systems
K. FabricationL. Installation M. InspectionN. Surveys O. Platform ReuseP. Minimum StructuresQ Commentary
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
147
and SystemsI. Materials
Q. Commentary
Introduction to Analysis of Offshore Structures
Resistance Factors inAPI RP 2A – LRFD
Loading Type Resistance FactorAxial Tension 0.95Axial Compression
0.85
Bending 0.95Shear 0.95
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
148
Hoop Buckling 0.80Connections 0.9 - 0.95
5/6/2011
75
Introduction to Analysis of Offshore Structures
Load Combinations in API RP2A – LRFD
• Factored gravity loads• 1.3D1 + 1.3D2 + 1.5L1 + 1.5L21 2 1 2
• Wind, wave and current loads• 1.1D1 + 1.1D2 + 1.1L1 + 1.35(We + 1.25Dn)• 0.9D1 + 0.9D2 + 0.8L1 + 1.35(We + 1.25Dn)• 1.3D1 + 1.3D2 + 1.5L1 + 1.5L2 + 1.2(Wo + 1.25Dn)
• Earthquake• 1.1D1 + 1.1D2 + 1.1L1 + 0.9E
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
149
• 0.9D1 + 0.9D2 + 0.8L1 + 0.9E
Introduction to Analysis of Offshore Structures
Loading Definitions
• D1 – Dead Load 1, e.g. Self weight• D2 – Dead Load 2, e.g. equipment weight2 , g q p g• L1 – Live Load 1, e.g. weight of fluids• L2 – Live Load 2, e.g. operating forces• We – Extreme wind, wave and current loads• Wo – Operating wind, wave and current loads• Dn – Inertial Load correspond to Wo
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
150
5/6/2011
76
Introduction to Analysis of Offshore Structures
Environmental Considerations
• Normal environmental conditions• Expected to occur frequently during the life of the structurestructure
• Extreme environmental conditions
• Recur with a return period of typically 100 years
• Earthquake environmental conditions
• Ground motion with a reasonable likelihood of notbeing exceeded at the site during the platform’s
5/2/2011 Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
151
being exceeded at the site during the platform slife (for strength check)
• Ground motion from a rare intense earthquake (fro ductility check)
Introduction to Analysis of Offshore Structures
Design Codes and Standards
Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
5/2/2011 152
5/6/2011
77
Introduction to Analysis of Offshore Structures
Who Produce and Distribute These Documents?
• National governments g• Certificate authorities• Technical standards committees• Companies, universities or individual expertise
Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
5/2/2011 153
Introduction to Analysis of Offshore Structures
Certification/Classification Authorities
They are independent bodiesThey are independent bodies • American Bureau of Shipping• ClassNK (NK)• Det Norkse Veritas (DNV)• Lloyds Register of Shipping (LR)• Noble Denton
Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
Noble Denton
5/2/2011 154
5/6/2011
78
Introduction to Analysis of Offshore Structures
Government Requirements
Legalities that need to be met• Norwegian Petroleum Directorate (NPD)• UK Health and Safety Executive (HSE)• US Mineral Management (MMS)
Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
5/2/2011 155
Introduction to Analysis of Offshore Structures
Codes and Standards
• A set of rules intended to insure safety • Impossible to write rules that fully apply to• Impossible to write rules that fully apply to every situation
• Fundamental premise of the code is to provide general stipulations to leave Sufficient latitude for the exercise ofengineering judgment
Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
5/2/2011 156
5/6/2011
79
Introduction to Analysis of Offshore Structures
Organizations
• American Petroleum Institute (API)• American Welding Society (AWS)g y ( )• Det Norkse Veritas (DNV)• Norwegian Technology Standards Institution(NTS)
• ISO/TC, Petroleum and Natural GasIndustries
• Subcommittee SC 7, Offshore Structures
Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
• The American Bureau of Shipping (ABS)
5/2/2011 157
Introduction to Analysis of Offshore Structures
Designer’s Responsibility
• Designer must understand the behavior for which the rule applieswhich the rule applies
• Behavioral understanding comes first, application of rules follows
• The designer has the ultimate responsibility of a safe structure
Engineering Judgment
Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
g g g
5/2/2011 158
5/6/2011
80
Introduction to Analysis of Offshore Structures
API Recommended Practice
• RP2A Recommended Practice for Planning, Designing and Construction Fixed Offshore g gPlatforms – Working Stress Design, 21st
Edition, 2000• RP2A Recommended Practice for Planning,
Designing and Construction Fixed Offshore Platforms – Load Resistance Factor
t d 993
Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
Design, 1st Edition, 1993
5/2/2011 159
Introduction to Analysis of Offshore Structures
DNV Offshore Rules & Standards
• OS–C101: Design of Offshore SteelSt t G l (LRFD th d) (2004)Structures, General (LRFD method) (2004)
• OS-C201: Structural Design of Offshore Units(WSD method) (2002)
• Rules for the Design Construction andInspection of Offshore Structures
• Appendix C: Steel Structures (1974) ASD d (1977) LRFD
Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
• (1974) ASD and (1977) LRFD
5/2/2011 160
5/6/2011
81
Introduction to Analysis of Offshore Structures
American Welding Society
• AWS D1.1 Structural Welding Code W ldi P d t• Welding Procedure etc.
• Strength of tubular joints
Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
5/2/2011 161
Introduction to Analysis of Offshore Structures
NORSOK Standard
• N-004 Design of steel structures (Rev.1, Dec1998)
• NS 3472 Design Rules for steels structures,(1984)
Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
5/2/2011 162
5/6/2011
82
Introduction to Analysis of Offshore Structures
ISO Standards
• ISO 13919-2:1995 Petroleum and natural gas industries -- Offshore Structures – Part 2:industries -- Offshore Structures – Part 2: Fixed steel structures
• Contains API RP2A LRFD :1993• Approved as an European Standard (EN ISO)
• ISO 19902, Petroleum and natural gas industries – Fixed steel offshore structures
Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
industries Fixed steel offshore structures
• Issued as Draft International Stanadard
5/2/2011 163
Introduction to Analysis of Offshore Structures
ISO Standards for Offshore Structures
• ISO 19902, Fixed Steel Structures• ISO 19903, Fixed Concrete Structure• ISO 1990, Fixed Offshore Structures
• Part 1: Monohulls, semi submersibles• Part 2: Tension leg platforms
• ISO 19905, Site-specific assessments of offshore units
Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
• Part 1: Jack-ups • Part 2: Jack-ups Commentary
• ISO 19906, Artic offshore structures5/2/2011 164
5/6/2011
83
Introduction to Analysis of Offshore Structures
ISO Standards for Offshore Structures
• ISO 19900, Genera requirements for offshoret tstructures
• ISO 19901, Specific requirements for offshorestructures
• Part 1: Metocean design and operating considerations• Part 2: Seismic design procedures and criteria• Part 3: Topsides structure• Part 4: Geotechnical and foundation design considerations
P t 5 W i ht t l d i i i d t ti
Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
• Part 5: Weight control during engineering and construction• Part 6: Marine operations• Part 7: Station keeping systems for floating offshore structures and mobile offshore units
5/2/2011 165
Introduction to Analysis of Offshore Structures
Health & Safety Executive
• Offshore installations: guidance on design ,construction and certification (fourth edition)19901990.
• Have since been revoked• Some sections of the guidance have beenmade available as individual reports in the Offshore Technology (OTO) series
Dr. S. NallayarasuDepartment of Ocean Engineering
Indian Institute of Technology Madras-36
5/2/2011 166