Inline RF-104 Refrigerator/ Installation Icemaker Instructions · Consult your local plumbing codes...
Transcript of Inline RF-104 Refrigerator/ Installation Icemaker Instructions · Consult your local plumbing codes...
Version 1.0C
RF-104 Installation Instructions
Step 1
Step 2
Step 3
As Easy As...
REFRIGERATOR
InlineRefrigerator/IcemakerFilter
Connects To Incoming Water Line
Front View Back View
System Tested and Certified by NSF International against NSF/ANSI 42 and 372 for the reduction of the claims specified on the Performance Data Sheet.
Inline Refrigerator/Icemaker Filter Model RF-104
2
Tools & Materials Required
Inline Icemaker Filtermain:
tools needed for installation
hacksaw
pipe cutter (for copper pipe installation)
shut off valve
saddle top valve with shut off
1/4" plastic tubing
package contents
optional items
utility knife
1 2 3
30’
tape measure safety glasses
filter
bucketbucket
Filter Model No. Date Purchased / Date to Replace For FREE Filter ReplacementReminder, go to
www.protectplus.com
My Brita® Universal Filtration System (Replace filter every 6 months)
Internet & Mobile866.709.2086 Free Installation Video
Manufactured for: Protect Plus, LLC 420 3rd Avenue NW, Hickory, NC 28601 USA
3RF-104 installation instructions Version 1.0C
Before You Begin
WARNING: Be sure that all electrical appliances and outlets are turned off at the circuit breaker before installing with this filter.
WARNING
Operation / Maintenance DataThese units are intended for non-commercial use. They should be used only in ambient air temperature of between 35 degrees F / 2 degrees C and 100 degrees F / 38 degrees C. Placement of these units in direct sunlight or use of electrical heating equipment on these units must be avoided. Replace filter cartridge when and as directed in the installation / operation instructions included with each cartridge. Replacement filter cartridges are available at retail outlets.
• These filters are not water purifiers. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.
• This unit is not designed to filter sulfur odor (rotten egg odor) caused by hydrogen sulfide. Use of carbon filters to treat sulfur odor may intensify taste/odor problems.
• Please comply with all state and local regulations regarding the installation of water treatment devices.
• The contaminants or other substances reduced by the water filter device are not necessarily in your water.
Filtration Facts
Please read all instructions, specifications, and precautions before installing and using your water filter system.
NOTICEPrecautions: for cold water use only.
Before installation be sure there is enough slack in the tubing to move refrigerator out for cleaning under refrigerator.
Consult your local plumbing codes and install accordingly.
This filter must be protected from freezing, which can cause cracking of the filter and water leakage.
Because of the product’s limited service life and to prevent costly repairs or possible water damage, we strongly recommend that the filter be replaced every six months or 4,000 gallons. If the filter has been in use for longer than this period, it should be replaced immediately. Date the top of any new head to indicate the next recommended replacement date.
DANGER: EXPLOSIVE FIRE HAZARD. If your refrigerator is gas powered, double check to determine which lines are gas lines and which are water lines.
DANGER!
Helpful Hints
4
Step 1 Shut off water
Attach inbound water line to filter
Step 2
Install filter and test for leaks
Step 3
As Easy As...
• Locate the water line to your refrigerator. • Observe if it is a flexible hose or a rigid. • Rigid pipes may require cutting. • Determine if you have all appropriate fasteners and adapters to fit your plumbing.• Consult your local plumbing codes and install accordingly.• Be sure to unplug appliance before working on refrigerator.• If refrigerator is gas powered double check lines leading into the refrigerator.
Before You Start WARNING! DANGER
For water lines larger than 1/4" OD or made from galvanized pipe additional plumbing hardware will be required. Please visit the local hardware store for these fittings or call customer service for assistance.
To Refrigerator
Supply line to Water Source
5RF-104 installation instructions Version 1.0C
• Shut off the water supply to the refrigerator and shut off the icemaker if applicable.• Have a container handy to catch any water that leaks during installation.• Turn off water supply to the refrigerator and dispense the water from the refrigerator door until water flow stops. • This releases pressure from the pipes before installation.
Step 1 Shut Off Water
WARNING
do not bend or crimp
cut squarely on both ends
do not cut at an angle
wet ends of tubing before inserting
• Select the desired spot to install the filter.• Cut the cold water line cleanly. No burrs.• Hold the filter so that the end marked "Outlet" is on the side pointing toward the refrigerator.• Insert the supply line side of the cold water line into the inlet side of the filter with endcap labeled "Inlet". • Push the line in firmly. • Give the line a gentle tug to be sure
that the line is properly seated.
Supply line to Water Source
bucket
DANGER
materials and tools needed
1 2 3
30’
tape measure utility knife
!
Step 2 Attach inbound water line to filter
Step 2 continued on next page >>
materials and tools needed
To Refrigerator
bucket
safety glasses
6Note: If leaks continue, turn off the water supply and call Customer Service or your local plumber.
Supply line to Refrigerator Source
• Turn on the water supply and flush the filter into the container for five minutes. • This flush will remove the air from the filter and the small carbon particles. During the flushing process, the water will turn dark in color. Continue flushing the new filter until the water runs clear.• Turn off the water supply.• Warning: DO NOT screw system head directly to refrigerator.• Water supply to the refrigerator should have a separate shut off valve installed before the filter.
bucket
WARNING
Step 2Attach inbound water line to filter
Step 3Install filter and test for leaks
<< Step continued from previous page
materials and tools needed
WARNING
• Insert the appliance side of the water line into the quick connect fitting. • Follow the same procedure as used for the supply side of the filter. • Turn on the water supply. • Check for leaks, verify that the tubing is cut cleanly and squarely and has been fully inserted into the quick connect fitting.
7RF-104 installation instructions Version 1.0C
• Replace filters every six months or when capacity is reached.
• Changing water filter on a regular basis ensures optimum performance of the water filter.
Filter Replacement(every 6 months)
Use and Care
Brita® Filter RF-104
The Brita® Inline Icemaker filter used with this filter system has a limited service life. Changes in taste, odor, and/or flow of the water being filtered indicate that the filter should be replaced.
RE
PLACE EVERY
SIX M ONTHS
Need Help? 1-866-709-2086Be sure to turn off the cold water supply until leak issue is resolved.
Note: If you have an existing in-line refrigerator filter with quick-connect fittings, simply push down on the outer ring of the quick connect fitting and pull the tubing out of the filter.
Please see the Performance Data Sheet for the certified performance of specific filters.
System
RF-104 Inline Refrigerator/Icemaker Filter
Flow Rate: 0.5 gpm (1.9 lpm)Operating pressure 30-100 psi (207-690 kPa)
Replace filters every six months or when capacity is reached.
8
9RF-104 installation instructions Version 1.0C
Instrucciones de instalación del RF-104Refrigerador
Filtro en línea refrigerador/máquina de hacer hielo
Paso 1
Paso 2
Paso 3
Tan fácil como...
Se conecta a la línea de entrada de agua
vista frontal vista posterior
Sistema comprobado y certificado por NSF Internacional contra NSF/ANSI 42 y 372 para la reducción de los reclamos especificados en la hoja de datos de rendimiento.
Filtro en línea refrigerador/máquina de hacer hielo Modelo RF-104
10
FIltro filtro en línea fabricante del hielo
Principal:
Implementos necesarios para la instalación
Contenido del paquete
artículos opcionales
bucketcubo
Sistema de filtración universal My Brita® (reemplace el filtro cada 6 meses)
866.709.2086Información del producto y servicio www.protectplus.com www.protectplus.com
Video de instalación gratuitoInternet y móvil
Número de modelo del filtro Fecha de compra / Fecha de cambio Para recordatorios GRATIS de cambio del filtro, ingrese a
www.protectplus.com
Implementos y materiales necesarios
Filtro
Fabricado por: Protect Plus, LLC 420 3rd Avenue NW, Hickory, NC 28601 USA
Cuchilla multiuso
1 2 3
30’
Cinta para medir
Gafas de seguridad
segueta
cortador de tubos (para instalación de tubos de cobre)
válvula de cierre
válvula de montura superior con cierra
tuberia plástica de 1/4"
11RF-104 installation instructions Version 1.0C
ADVERTENCIA: Verifique que todos los electrodomésticos y los tomacorrientes estén desconectados en el interruptor de circuito principal antes de trabajar en el área del gabinete.
ADVERTENCIA
Información de funcionamiento/mantenimientoEstas unidades no están destinadas para uso comercial. Deben utilizarse sólo en ambientes donde la temperatura del aire está entre 35 grados F / 2 grados C y 100 grados F / 38 grados C. Debe evitar colocar estas unidades en la luz solar directa o el uso de equipo de calefacción. Cambie el cartucho del filtro como y cuando lo indiquen las instrucciones de instalación/operación que se incluyen con cada cartucho. Los cartuchos de reemplazo del filtro están a disposición en las tiendas al detal.
• Estos filtros no son purificadores de agua. No utilice con agua que sea microbiológicamente insegura o de calidad desconocida sin la adecuada desinfección antes o después del paso por el sistema. Los sistemas certificados para la disminución de quistes pueden ser utilizados en aguas desinfectadas que puedan contener quistes filtrables. • Esta unidad no está diseñada para filtrar azufre (olor a huevos podridos). Utilizar filtros de carbón para tratar el azufre puede intensificar los problemas de sabor/olor.
• Cumpla con todas las regulaciones estatales y locales relacionadas con la instalación de las unidades para tratamiento de agua.• Los contaminantes u otras sustancias que disminuye esta unidad de filtración de agua no están necesariamente en el agua de su vivienda.
Datos sobre la filtración
Lea todas las instrucciones, especificaciones y precauciones antes de instalar o utilizar su sistema de filtración de agua
Debido a la limitada vida útil del producto y para evitar reparaciones costosas o posibles daños por agua, se recomienda que el filtro sea reemplazado cada seis meses o 4,000 galones. Si el filtro ha estado en uso durante más de ese período, debe ser sustituido inmediatamente. Conocer la parte superior de cualquier nueva cabeza para indicar la próxima fecha de reemplazo recomendado.
AVISO
Este filtro debe ser protegida de la congelación, lo que puede causar el agrietamiento de la fuga de filtro y agua.
Antes de la instalación asegúrese de que haya suficiente holgura en el tubo para mover el refrigerador a cabo para limpiar debajo del refrigerador.Consulte la normativa local de plomería e instale según se indica.
PELIGRO: EXPLOSIÓN PELIGRO DE INCENDIO. Si su refrigerador es a gas, verifique dos veces para determinar qué líneas son las líneas de gas y cuáles son las líneas de agua.
PELIGRO!
Antes de comenzar
Precauciones: para uso con agua fría únicamente.
12
Consejos útiles
• Ubique la tubería de agua de su refrigerador.• Observe si es una manguera flexible o rígida. • Es posible que necesite cortar los tubos rígidos.• Determine si tiene todos los sujetadores y adaptadores adecuados para adaptar la plomería.• Consulte la normativa local de plomería e instale según se indica. • Cerciórese de desenchufar el electrodoméstico antes de trabajar en el refrigerador. • Si el refrigerador es de gas, revise nuevamente las tuberías que ingresan al refrigerador.
Antes de comenzar
Paso 1 Desconecte el agua
Conecte la línea de agua entrante para filtrar
Paso 2
Instale el filtro y la prueba de fugas
Paso 3
Tan fácil como....
ADVERTENCIA! PELIGRO
Para tuberías de agua mayores de 1/4" de diámetro externo o elaboradas en tubo galvanizado. Se requieren accesorios adicionales de plomería adicionales. Visite la ferretería local para adquirir estos acoples o llame al servicio al cliente para obtener asistencia.
Al Refrigerador
Tuberia de entrada a suminstro de agua
13RF-104 installation instructions Version 1.0C
• Corte el suministro de agua hacia el refrigerador y cierre la válvula del fabricador de hielo, si fuese pertinente. • Tenga un envase a mano para recoger el agua que pueda gotear durante la instalación. • Corte el suministro de agua al refrigerador y descargue el agua de la puerta del refrigerador hasta que el flujo se detenga. • Esto alivia la presión de las tuberías antes de la instalación.
Paso 1 Desconecte el agua
ADVERTENCIA
no doble ni engarzar
Corte en ángulo recto en ambos extremos
no corte en ángulo
Moje los extremos de la tubería antes de insertarla
• Seleccione el lugar deseado para instalar el filtro. • Corte la tubería de agua fría perfectamente. Sin que queden rebabas.• Sostenga el filtro de modo que el extremo marcado “Outlet” (salida) esté en el lado orientado hacia el refrigerador. • Inserte el lado de la tubería de suministro de agua fría en el lado de la toma del filtro que está marcado como "Inlet" (entrada). • Empuje la tubería firmemente. • Hale suavemente la tubería para comprobar que esté adecuadamente insertada.
Tuberia de entrada a suminstro de agua
cubo
PELIGRO
Materiales e implementos necesarios
1 2 3
30’
cinta para medir
cuchilla multiuso
!
Paso 2Fije la tubería de agua de entrada al filtro.
Paso 2 - Continúa en la página siguiente >>
Materiales e implementos necesarios
Al Refrigerador
cubo
Gafas de seguridad
14
• Inserte el lado de la tubería de agua del electrodoméstico en el acople de conexión rápida.• Siga el mismo procedimiento utilizado para el lado de suministro del filtro. • Abra el suministro de agua. • Revise si hay fugas; verifique que la tubería esté cortada perfectamente y a escuadra y que esté totalmente insertada en el acople de conexión rápida.
Nota: Si la fuga continúa, cierre el suministro de agua y llame al Departamento de servicio al cliente o a un plomero local.
Línea de suministro de al refrigerado
• Abra el suministro de agua y purgue el filtro en el envase durante cinco minutos.• Esta purga eliminará el aire del filtro y las pequeñas partículas de carbón. Durante el proceso de purga, el agua se tornará de color oscuro. Continúe purgando el filtro nuevo hasta que el agua salga transparente.• Cierre el suministro de agua.• Advertencia NO enrosque el cabezal del sistema directamente al refrigerador.
• El suministro de agua del refrigerador debe tener una válvula de cierre separada instalada antes del filtro.
cubo
ADVERTENCIA
Paso 2Conecte la línea de agua entrante para filtrar
Paso 3Instale el filtro y la prueba de fugas
<< Paso viene de la página anterior Materiales e implementos necesarios
ADVERTENCIA
15RF-104 installation instructions Version 1.0C
• Reemplace los filtros cada seis meses o cuando se alcanza la capacidad.
• Cambio de filtro de agua de forma regular garantiza un rendimiento óptimo del agua filtrar.
Cambio del filtro(cada 6 meses)
Uso y cuidado
Filtro Brita® RF-104
El filtro Dispensador de agua caliente Brita ® en línea utilizado con este sistema de filtro tiene una vida útil limitada. Los cambios en el sabor, olor, y / o el caudal del agua filtrada indican que el filtro debe ser sustituido.
RE
PLACE EVERY
SIX M ONTHS
¿Necesitas ayuda? 1-866-709-2086Asegúrese de cerrar el suministro de agua fría hasta que se resuelva problema de pérdida.
Nota: Si usted tiene un filtro exsisting refrigerador en línea con accesorios de conexión rápida, simplemente empuje el anillo uter del accesorio de conexión rápida y saque el tubo de salida del filtro.
Consulte la Hoja (“ó ficha”) de Datos de rendimiento para el rendimiento certificado de sistemas específicos con los cartuchos indicados.
Sistema
Filtro en línea refrigerador/máquina de hacer hielo de Brita® RF-104
Caudal: 0.5 gpm (1.9 lpm)Presion de operación 30-100 psi (207-690 kPa)
Reemplace los filtros cada seis meses o cuando se alcanza la capacidad.
Great-tasting water >
When water tastes better,you'll drink more of it
Agua de estupendo sabor
Si el agua tiene mejor sabor, beberá más
Carbon Filtration2 >
Designed to reduce chlorine (taste and odor)2 found in tap water, leaving you with great-tasting water.
Disminuye el cloro (sabor y olor)2
Los filtros Brita® disminuyen el cloro (sabor y olor)2 que se encuentra en el agua del grifo, brindándole un agua de estupendo sabor
Products to fit your life >
A variety of Brita® products to fit you and your family's lifestyle
Productos que se adaptan a su estilo de vida
Una diversidad de productos Brita® que se adaptan a usted y al estilo de vida de su familia
1 No bottles to throw away.
2 Substances reduced may not be in all users' water. Not all filters with carbon have certified reduction claims.
3 Can save money versus bottled water.
1 Sin botellas que desechar.
2 Las sustancias que disminuye puede que no estén en el agua de todos los usuarios.
3 Se puede ahorrar dinero en comparación con el agua embotellada.
Great-Tasting Water that's better for the environment1
Gran degustación de agua que es mejor para el medio ambiente1
Better for the environment,and your wallet3 >
Visit Brita online at www.Brita.comto learn how you can make a positive impact on the environment
Es mejor para el medio ambiente y su cartera3
Visite Brita® a través de Internet en www.Brita.com para conocer cómo hacer un impacto positivo en el medio ambiente
© 2016 Protect Plus. The BRITA trademark and logo are registered trademarks of Brita LP and are used under license by Protect Plus, LLC. All rights reserved.
© 2016 Protect Plus. La marca comercial BRITA y el logotipo son marcas comerciales registradas de Brita LP y se utilizan bajo licencia de Protect Plus, LLC. Todos los derechos reservados.
Always seePerformance Data
Sheet forNSF Certified
claims.