Infrastructure components PROFIBUS DP · InduSol Gmb w Blumenstrasse w0 Scmoelln wPone 9 0 91 510...
1
Indu-Sol GmbH – Specialist in Industrial Networks Indu-Sol GmbH • Blumenstrasse 3 • 04626 Schmoelln • Phone: +49 (0) 34491 5818-0 • Fax: +49 (0) 34491 5818-99 • info@indu-sol.com • www.indu-sol.com Updated 05/2016 Connector PG/90° Fast Connect Engineering drawing Functional diagram Connector PG/90° Fast Connect Function The PG/Service interface serves as feedback-free measuring point for mea- surements with PROFtest II XL/PROFI-TM Professional and PB-INspektor® NT can also be used as programming interface. The plug is completely shielded by the metal-coated casing. The design meets the Fast Connect requirement. The plug for the terminating resistor that is accessible from outside, dis- connects the outgoing segment when being in ON position. The design meets the Fast Connect requirement. Bus connection • 9-pin sub-D interface • Insulation piercing terminal (suitable for „Fast Connect“ cable) • 90° cable outlet Electrical parameters • Terminating resistor: integrated, can be switched with a sliding switch from outside • Baud rate: 9.6 kbps to 12 Mbps • Supply voltage: 4.75 to 5.25 VDC has to be provided by each PROFIBUS user (Pin 5 GND, Pin 6 +5V) • Current drain: 12,5 mA Ambient conditions • Operating temperature: -20 °C to +75 °C • Transport / storage temperature: -25 °C to +80 °C • Industrial protection: IP20 Design • Dimensions (H x W x D): 65 x 16 x 41 mm • Interface: 9-pin sub-D • Weight: approx. 80 g • Casing: zinc die cast CE mark Plugs are passive components and are subject to the CE mark system pursuant to EU Directives. Ordering details Art. No. Connector PG/90° Fast Connect 110050010 65 mm 41 mm Infrastructure components PROFIBUS DP Width: 16 mm
Transcript of Infrastructure components PROFIBUS DP · InduSol Gmb w Blumenstrasse w0 Scmoelln wPone 9 0 91 510...
Indu-Sol GmbH – Specialist in Industrial Networks
Indu-Sol GmbH • Blumenstrasse 3 • 04626 Schmoelln • Phone: +49 (0) 34491 5818-0 • Fax: +49 (0) 34491 5818-99 • [email protected] • www.indu-sol.com
Upd
ated
05/
2016
Connector PG/90° Fast Connect
Engineering drawing
Functional diagram
Connector PG/90° Fast ConnectFunction
The PG/Service interface serves as feedback-free measuring point for mea-surements with PROFtest II XL/PROFI-TM Professional and PB-INspektor® NT can also be used as programming interface. The plug is completely shielded by the metal-coated casing. The design meets the Fast Connect requirement.The plug for the terminating resistor that is accessible from outside, dis-connects the outgoing segment when being in ON position. The design meets the Fast Connect requirement.
Bus connection
• 9-pin sub-D interface • Insulation piercing terminal (suitable for „Fast Connect“ cable) • 90° cable outlet
Electrical parameters
• Terminating resistor: integrated, can be switched with a sliding switch from outside • Baud rate: 9.6 kbps to 12 Mbps • Supply voltage: 4.75 to 5.25 VDC has to be provided by each PROFIBUS user (Pin 5 GND, Pin 6 +5V) • Current drain: 12,5 mA
Ambient conditions
• Operating temperature: -20 °C to +75 °C • Transport / storage temperature: -25 °C to +80 °C • Industrial protection: IP20
Design
• Dimensions (H x W x D): 65 x 16 x 41 mm • Interface: 9-pin sub-D • Weight: approx. 80 g • Casing: zinc die cast
CE mark
Plugs are passive components and are subject to the CE mark system pursuant to EU Directives.
Ordering details Art. No.
Connector PG/90° Fast Connect 110050010
65 mm
41 mm
Infrastructure components PROFIBUS DP
Width: 16 mm
