INFRARED ABSORPTION SPECTROSCOPY
-
Upload
ivan-russell -
Category
Documents
-
view
226 -
download
13
description
Transcript of INFRARED ABSORPTION SPECTROSCOPY
INFRARED ABSORPTION SPECTROSCOPY
Semester Dec – Apr 2010
LEARNING OUTCOMES By the end of this topic, students should be able to:
Explain the principles and the working mechanism of infrared (IR) absorption spectroscopy
Identify the molecular species that absorb IR radiation Interpret IR spectrum Explain stretching and bending vibrations in relation to IR
absorption Determine unknown qualitatively using IR absorption Draw a schematic diagram of a conventional IR
instrument and a fourier transform IR instrument and explain the function of each component of the instrument
Differentiate between a dispersive IR instrument and a FTIR spectrometer 2
INFRARED SPECTROSCOPY
Mostly for qualitative analysis Absorption spectra is recorded as
transmittance spectra Absorption in the infrared region arise from
molecular vibrational transitions Absorption at specific wavelengths Thus, IR spectra provides more specific
qualitative information IR spectra is called “fingerprints” - because no other chemical species
will have identical IR spectrum 3
COMPARISON BETWEEN TRANSMITTANCE (UPPER) VS ABSORBANCE (LOWER) PLOT
The transmittance spectra provide better contrast btw intensities of strong and weak bands compared to absorbance spectra
4
ELECTROMAGNETIC SPECTRUM
Energy of IR photon insufficient to cause electronic excitation but can cause vibrational excitation
5
INTRODUCTION
Comparison between UV-vis and IR
Energy: UV > vis > IRFrequency: UV > vis > IRWavelength: UV < vis < IR
6
INFRARED SPECTROSCOPY
Infrared (IR) spectroscopy deals with the interaction of infrared radiation with matter
IR spectrum provides: Important information about its chemical nature
and molecular structure
IR applicability:Analysis of organic materialsPolyatomic inorganic moleculesOrganometallic compounds 7
IR region of EM spectrum:λ: 780 nm – 1000 μmWavenumber: 12,800 – 10cm-1
IR region subdivided into 3 subregions:
1. Near IR region (Nearest to the visible)- 780 nm to 2.5 μm (12,800 to 4000 cm-1)
2. Mid IR region- 2.5 to 50 μm (4000 – 200 cm-1)
3. Far IR region- 50 to 1000 μm (200 – 10cm-1)
infr
ared
microwave
visible
NEAR
MID
FAR
8
8
When IR absorption occur?
1. IR absorption only occurs when IR radiation interacts with a molecule undergoing a change in dipole moment as it vibrates or rotates.
2. Infrared absorption only occurs when the incoming IR photon has sufficient energy for the transition to the next allowed vibrational state
Note: If the 2 rules above are not met, no absorption can occur
9
WHAT HAPPEN WHEN A MOLECULE ABSORBS INFRARED RADIATION?
Absorption of IR radiation corresponds to energy changes on the order of 8 to 40 kJ/mole. - Radiation in this energy range corresponds to
stretching and bending vibrational frequencies of the bonds in most covalent molecules.
In the absorption process, those frequencies of IR radiation which match the natural vibrational frequencies of the molecule are absorbed.
The energy absorbed will increase the amplitude of the vibrational motions of the bonds in the molecule.
10
NOT ALL bonds in a molecule are capable of absorbing IR energy. Only those bonds that have change in dipole moment are capable to absorb IR radiation.
The larger the dipole change, the stronger the intensity of the band in an IR spectrum.
11
What is a dipole moment?
is a measure of the extent to which a separation exists between the centers of positive and negative charge within a molecule.
O
H Hδ+
δ-
δ+12
In heteronuclear diatomic molecule, because of the difference in electronegativities of the two atoms, one atom acquires a small positive charge (q+), the other a negative charge (q-).
This molecule is then said to have a dipole moment whose magnitude, μ =qd
distance of separation of the charge
13
MOLECULAR SPECIES THAT ABSORB INFRARED RADIATION
Compound absorb in IR regionOrganic compounds, carbon
monoxide
Compounds DO NOT absorb in IR regionO2, H2, N2, Cl2
14
IR VIBRATIONAL MODES
15
Molecular vibration
divided into
stretching bending
back & forth movement
involves change in bond angles
symmetrical asymmetrical
scissoring
rocking twisting
wagging
in-plane vibration
out of plane vibration
16
STRETCHINGSTRETCHING
17
BENDINGBENDING
18
SAMPLE HANDLING TECHNIQUES
Gases evacuated cylindrical cells equipped with
suitable windows
Liquid sodium chloride windows “neat” liquid
Solid Pellet (KBr) Mull 19
LIQUID
a drop of the pure (neat) liquid is squeezed between two rock-salt plates to give a layer that has thickness 0.01mm or less
2 plates held together by capillary mounted in the beam path
What is meant by “neat” liquid? Neat liquid is a pure liquid that do not contain any solvent or
water.
This method is applied when the amount of liquid is small or when a suitable solvent is unavailable
20
SOLID SAMPLE PREPARATION
There are three ways to prepare solid sample for IR spectroscopy.
Solid that is soluble in solvent can be dissolved in a solvent, most commonly carbon tetrachloride CCl4.
Solid that is insoluble in CCl4 or any other IR solvents can be prepared either by KBr pellet or mulls.
21
PELLETING (KBr PELLET)
Mixing the finely ground solid sample with potassium bromide (KBr) and pressing the mixture under high pressure (10,000 – 15,000 psi) in special dye.
KBr pellet can be inserted into a holder in the spectrometer.
22
MULLS
Formed by grinding 2-5 mg finely powdered sample, presence 1 or 2 drops of a heavy hydrocarbon oil (Nujol)
Mull examined as a film between flat salt plates
This method applied when solid not soluble in an IR transparent solvent, also not convenient pelleted in KBr 23
What is a mull A thick paste formed by grinding an insoluble
solid with an inert liquid and used for studying spectra of the solid
What is Nujol A trade name for a heavy medicinal liquid
paraffin. Extensively used as a mulling agent in spectroscopy
24
INSTRUMENTATION
25
IR INSTRUMENT
Dispersive spectrometers sequential mode
Fourier Transform spectrometers simultaneous analysis of the full spectra range
using inferometry
26
IR INSTRUMENT (DISPERSIVE)
Important components in IR dispersive spectrometer
sourcelamp
sampleholder
λselector
detectorsignal processor
& readout
1 2 3 4 5
Source:
- Nernst glower
- Globar source
- Incandescent wire
Detector:
- Thermocouple
- Pyroelectric transducer
- Thermal transducer27
RADIATION SOURCES
generate a beam with sufficient power in the λ region of interest to permit ready detection & measurement
provide continuous radiation; made up of all λ’s with the region (continuum source)
stable output for the period needed to measure both P0 and P
28
SCHEMATIC DIAGRAM OF A DOUBLE BEAM INFRARED SPECTROPHOTOMETER
29
FTIRFOURIER TRANSFORM INFRARED
30
FTIR
Why is it developed?
to overcome limitations encountered with the dispersive instruments
especially slow scanning speed; due to individual measurement of molecules/atom
utilize an interferometer
31
Interferometer Special instrument which can read IR frequencies
simultaneously faster method than dispersive instrument interferograms are transformed into frequency
spectrums by using mathematical technique called Fourier Transformation
FTCalculations
interferograms IR spectrum
32
COMPONENTS OF FOURIER TRANSFORM INSTRUMENT
- majority of commercially available Fourier transform infrared instruments are based upon Michelson interferometer
1
3
2
4
5
6
33
Advantages (over dispersive instrument)
high sensitivity high resolution speed of data acquisition ( data for an entire spectrum
can be obtained in 1 s or less)
34
INTERPRETATION INFRARED SPECTRA
35
IR spectrum is due to specific structural features, a specific bond, within the molecule, since the vibrational states of individual bonds represent 1 vibrational transition.
e.g. IR spectrum can tell the molecule has an O-H bond or a C=O or an aromatic ring
INFRARED SPECTRA
36
INFRARED SPECTRA
37
HOW TO INTERPRET INFRARED SPECTRA?
38
39
Indicates:
Are any or all to the right of 3000?alkyl groups (present in most organic molecules)
Are any or all to the left of 3000?a C=C bond or aromatic group in the molecule
1. Begin by looking in the region from 4000-1300.Look at the C–H stretching bands around 3000:
How to analyze IR spectra
40
2. Look for a carbonyl in the region 1760-1690. If there is such a band:
Indicates:
Is an O–H band also present? a carboxylic acid group
Is a C–O band also present? an ester
Is an aldehyde C–H band also present?
an aldehyde
Is an N–H band also present? an amide
Are none of the above present? a ketone
(also check the exact position of the carbonyl band for clues as to the type of carbonyl compound it is)
41
3. Look for a broad O–H band in the region 3500-3200 cm-1.
If there is such a band:
Indicates:
Is an O–H band present? an alcohol or phenol
4. Look for a single or double sharp N–H band in the region 3400-3250 cm-1. If there is such a band:
Indicates:
Are there two bands? a primary amine
Is there only one band? a secondary amine
42
5. Other structural features to check for:
Indicates:
Are there C–O stretches?an ether (or an ester if there is a carbonyl band too)
Is there a C=C stretching band? an alkene
Are there aromatic stretching bands? an aromatic
Is there a C≡C band? an alkyne
Are there -NO2 bands? a nitro compound
If there is an absence of major functional group bands in the region 4000-1300 cm-1 (other than C–H stretches), the compound is probably a strict hydrocarbon.
Also check the region from 900-650 cm-1. Aromatics, alkyl halides, carboxylic acids, amines, and amides show moderate or strong absorption bands (bending vibrations) in this region.
As a beginning student, you should not try to assign or should not try to assign or interpret every peak in the spectrum.interpret every peak in the spectrum. Concentrate on learning the major bands and recognizing their presence and absence in any given spectrum.
How to analyze IR spectra
43
44
45
ALKANE
46
C C
H
H
H
H
H C H
H
H
n
C-H Stretch for sp3 C-H around 3000 – 2840 cm-1.CH2 Methylene groups have a characteristic bending absorption at approx 1465 cm-1
CH3 Methyl groups have a characteristic bending absorption at approx 1375 cm-1
CH2 The bending (rocking) motion associated with four or more CH2 groups in an open chain occurs at about 720 cm-1
47
ALKENE
48
C C
H H
H H
=C-H Stretch for sp2 C-H occurs at values greater than 3000 cm-
1.=C-H out-of-plane (oop) bending occurs in the range 1000 – 650 cm-1
C=C stretch occurs at 1660 – 1600 cm-1; often conjugation moves C=C stretch to lower frequencies and increases the intensity
ALKENE
49
ALKYNE
HC CH
50
CH
C C
Stretch for sp C - H occurs near 3300 cm-1.
Stretch occurs near 2150 cm-1; conjugation moves stretch to lower frequency.
ALKYNE
51
AROMATIC RINGS
C H Stretch for sp2 C-H occurs at values greater than 3000 cm-1.
C C Ring stretch absorptions occur in pairs at 1600 cm-1 and 1475 cm-1.
C H Bending occurs at 900 - 690cm-1.52
AROMATIC RINGS
53
C-H Bending ( for Aromatic Ring)
The out-of-plane (oop) C-H bending is useful in order to assign the positions of substituents on the aromatic ring.
Monosubstituted rings•this substitution pattern always gives a strong absorption near 690 cm-1. If this band is absent, no monosubstituted ring is present. A second strong band usually appears near 750 cm-1.
Ortho-Disubstituted rings•one strong band near 750 cm-1.
Meta- Disubstituted rings•gives one absorption band near 690 cm-1 plus one near 780 cm-
1. A third band of medium intensity is often found near 880 cm-1.
Para- Disubstituted rings - one strong band appears in the region from 800 to 850 cm-1.54
Bending observed as one strong band near 750 cm-1.C H
Ortho-Disubstituted rings
55
Meta- Disubstituted rings
- gives one absorption band near 690 cm-1 plus one near 780 cm-1. A third band of medium intensity is often found near 880 cm-1.
C H
56
Para- Disubstituted rings
- one strong band appears in the region from 800 to 850 cm-1.
C H
57
ALCOHOL
C
CH3
CH3
H3C OH
Primary alcohol 10
Secondary alcohol 20
Tertiary alcohol 30
C C OH
H
H
H
H
HC C C
H
H
H
OH
H
H
H
H
58
ALCOHOL
O-H The hydrogen-bonded O-H band is a broad peak at 3400 – 3300 cm-1. This band is usually the only one present in an alcohol that has not been dissolved in a solvent (neat liquid). C-O-H Bending appears as a broad and weak peak at 1440 – 1220 cm-1 often obscured by the CH3 bendings.C-O Stretching vibration usually occurs in the range 1260 – 1000 cm-1.
This band can be used to assign a primary, secondary or tertiary structure to an alcohol.
59
PHENOL
OH
60
PHENOL
61
62
ETHER
R O R'C-O The most prominent band is that due to C-O stretch, 1300 – 1000 cm-1.
Absence of C=O and O-H is required to ensure that C-O stretch
is not due to an ester or an alcohol.
Phenyl alkyl ethers give two strong bands at about 1250 – 1040 cm-1,
while aliphatic ethers give one strong band at about 1120 cm-1. 63
64
CARBONYL COMPOUNDS
cm-1
1810 1800 1760 1735 1725 1715 1710 1690
Anhydride Acid Anhydride Ester Aldehyde Ketone Carboxylic Amide(band 1) Chloride (band 2) acid
Normal base values for the C=O stretching vibrations for carbonyl groups
65
A. ALDEHYDE
R C
O
H
R C
O
H
Ar C
O
H
C=O stretch appear in range 1740-1725 cm-1 for normal aliphatic aldehydes
Conjugation of C=O with phenyl; 1700 – 1660 cm-1 for C=Oand 1600 – 1450 cm-1 for ring (C=C)
C-H Stretch, aldehyde hydrogen ( -CHO), consists of weak bands, one at 2860 - 2800 cm-1 and
the other at 2760 – 2700 cm-1.66
67
B. KETONE
C R'R
OC R'R
O
C R'Ar
O
C=O stretch appear in range 1720-1708 cm-1 for normal aliphatic ketones
Conjugation of C=O with phenyl; 1700 – 1680 cm-1 for C=Oand 1600 – 1450 cm-1 for ring (C=C)
68
69
C. CARBOXYLIC ACID
R C OH
O
70
71
D. ESTER
R C
O
O R
R C
O
O R
Ar C
O
O R
C – O Stretch in two or more bands, one stronger and broader than the other, occurs in the range 1300 – 1000 cm-1
C=O stretch appear in range 1750-1735 cm-1 for normal aliphatic esters
Conjugation of C=O with phenyl; 1740 – 1715 cm-1 for C=Oand 1600 – 1450 cm-1 for ring (C=C)
72
73
E. AMIDE
R C N
OH
HR C N
OH
RR C N
OR
R1020
30
74
AMIDE
75
F. ACID CHLORIDE
C Cl
O
R
C O
C Cl
Stretch appear in range 1810 -1775 cm-1 in conjugated chlorides. Conjugation lowers the frequency to 1780 – 1760 cm-1
Stretch occurs in the range 730 -550 cm-1
Acid chloride show a very strong band for the C=O group. 76
F. ANHYDRIDE
C O C
O O
RR
C OStretch always has two bands, 1830 -1800 cm-1 and 1775 – 1740 cm-1, with variable relative intensity. Conjugation moves the absorption to a lower frequency. Ring strain (cyclic anhydride) moves absorptions to a higher frequency.
C O Stretch (multiple bands) occurs in the range 1300 -900 cm-1 77
R NH
HR
HN R
R N R
R
AMINE
10 20
30
78
AMINE
Out-of-plane bending absorption can sometimes be observed near 800 cm-1
Stretch occurs in the range 1350 – 1000 cm-1
N – H
Bending in primary amines results in a broad band in the range 1640 – 1560 cm-1. Secondary amines absorb near 1500 cm-1
Stretching occurs in the range 3500 – 3300 cm-1. Primary amines have two bands.Secondary amines have one band: a vanishingly weak one for aliphatic compounds and a stronger one for aromatic secondary amines.Tertiary amines have no N – H stretch.
N – H
N – H
C – N 79
PRIMARY AMINE
Secondary Amine
80
TERTIARY AMINE
Aromatic Amine
81