Industrial Tools and Solutions.pdf

8/20/2019 Industrial Tools and Solutions.pdf

1/113

Industrial Tools and SolutionsAtlas Copco – The first choice when productivity counts


2/113

Industrial tools and solutions

M a t e r i a l r e m o v a l t o o l s

A s s e m b l y t o o l s

C O N T E N T S

Atlas Copco – the productivity provider ........................................ 2

Take your productivity to the next level ........................................ 4

Light deburring, die grinding and engraving ............................... 6Sanding, surface preparation and polishing ................................ 9

Heavy deburring, trimming and internal grinding ..................... 12

Heavy rough grinding and cutting off ......................................... 15

Medium rough grinding and rough sanding .............................. 18

Brazor Mark ll electric grinders .................................................... 21

Weld flux removal and multi purpose scaling ............................ 23

Chipping ......................................................................................... 26

Drilling ........................................................................................... 29

Drilling and tapping ..................................................................... 33

Five steps to eliminate errors, cut costs

and free-up production time ......................................................... 36

Impact wrenches. M6–M45 .......................................................... 38

Impact wrenches. Torque control M8–M22 ................................. 41

Screwdrivers. Direct drive and slip clutch M1.6–M6 .................. 44

Screwdrivers. Shut-off clutch M1.6–M5 ...................................... 47

ErgoPulse nutrunners. Non shut-off type M5–M16 .................... 50

ErgoPulse nutrunners. Shut-off type M5–M20 ............................ 53

Pulsor. Monitoring impulse tools ................................................. 58

Angle nutrunners. Shut-off type M2.5–M16 ............................... 60

Pistol grip nutrunners. Shut-off and stall type ........................... 63

MicroTorque electric screwdrivers ............................................... 67

Tensor DL/SL electric screwdrivers .............................................. 70

Tensor DS electric nutrunners ...................................................... 73

Tensor S/ST transducerised electric nutrunners ........................ 76

ETX nutrunners .............................................................................. 79

Quality assurance system for tightening tools ............................ 81

Torque arms ................................................................................... 86

Bits and power sockets ................................................................ 88

Air motors ...................................................................................... 95

Air hoists and trolleys ................................................................... 97

Airline accessories ........................................................................ 99

Airline accessories – selection guide ......................................... 101

Declaration of noise and vibration emission ........................... 105


3/113

2

Atlas Copco –the productivity provider At Atlas Copco we are good at listening. And after more than

130 years of listening, we know what our customers want:

superior productivity.

Over time, we have identified four ways to help you increase

productivity – innovative development, a commitment to quality,

creating better working conditions and maximizing uptime.

Innovations that boostproductivity

We believe that there is always a better

way of doing things. In fact, 50% of our

range – consisting of more than 3,000

tools – has been launched during

the past 3 years.

One good example isour top end 5´´ anglegrinder, the LSV 38.

Thanks to its out-

standing power-to-

weight ratio, this product increases

productivity by over 40% compared to

many competitive grinders.

Quality – perfectingyour process

Attention to quality means a lower scrap

rate, less reassembly and fewer recalls.

The later an error is identified, the moretime it takes to correct. In other words,

by increasing quality, you increase the

amount of time available for producing

new products.

Tensor ST tools will significantly improve

your assembly quality by giving effective

operator feedback. The built-in batch-count

signal helps eliminate missing fasteners,

and a unique configurable speaker on the

tool provides an alert if problems do occur.

Improving ergonomics

Productivity starts with people. If your

operators are subjected to lower noise and


4/113

3

vibration levels, they work better. We hired

our first expert in ergonomics as early as

1964. Today, ergonomics has become an

integral part of our design philosophy.

Our recoil-

less riveting

hammer, the RRH 06,

shows how innovative productdevelopment can lead to a

unique and efficient damping

system without increasing tool weight.

The RRH 06 has vibration levels that are

50% lower than conventional tools, signi-

ficantly reducing the risk of vibration-

induced white finger syndrome.

Keep your productionline producing

Once systems are installed, we are dedi-

cated to keeping your operations running.

With a range of different services – Fullcoverage service, Preventive maintenance,

Fixed price repairs, ToolScanTM – we can

meet a range of different needs.

Atlas Copco can offer a profitable

partnership on a local or global basis.

With a presence in 140 countries, we are

resourced to provide the same support

wherever you are located.


5/113

4

Take your productivity to the next levelSpeed up your operation by using tools that are efficient, powerful and ergonomic.

But don’t forget to look beyond the tool. The right accessories, working environment

and workstation design all have an impact on your productivity.

Remove more material faster– cut process time

Get more done in less time with our state-

of-the-art vane grinders and uniquely

powerful turbine grinders. Compare themto conventional tools and watch produc-

tivity surge.

Good ergonomics– good economics

Atlas Copco tools have been developed

to increase individual productivity by

minimizing operator fatigue. Our toolsfeature low noise and vibration levels. In

addition, they are designed with ergono-

mic grips to reduce physical strain,

which will help boost productivity.

Beyond the tool

To ensure optimal output, look beyond the

tool to accessories and installation. Even a

small change in your air installation can

have a major impact on productivity. Is ittime to re-examine the workstation as a

whole? We have the know-how to help

you make process improvements.


6/113

5

P r o d u c t i v

i t y i m p r o v e m e n t

Step by step you can improveyour productivity

Labour costs

Abrasives

Other costs

The tool

Typical distribution of costs in a grinding-operation (labour costs might vary in somecountries).

Step 2

Airlineupgrade

Step 3

Ergonomicdesign,

vane

grinderLSV 48

Step 4

TurbinegrinderGTG 21

Step 5

TurbinegrinderGTG 40

Step 1

+20%

+25%

+15%

+60%

Correct airpressure

•

Preventspressure

drop

Raisedindividualproduc-

tivity•

Greatperformance

High rateof material

removal•

Top efficiency

Enormouspower

•

Highestrate of

materialremoval

Presentproductivity

level

Examine your total costs

The cost of a tool is often a minor part of

the total cost of a typical grinding opera-

tion. By investing in powerful and ergo-

nomic tools, you can cut process times.

And by selecting efficient grinders, you

can reduce the consumption of abrasives.

Take your first step today

Why wait, when there are major produc-

tivity gains to be made?

M

a t e r i a l r e m o v a l



7/113

6

ApplicationsDie grinding and engraving using mounted points. Deburring of castings and generalfiling using rotary burrs in ferrous and non-ferrous materials.

The toolsThe high-speed and light-weight LSF 07 isideal in small detail precision die-makingapplications in a wide range of materials.The well-balanced pencil-style grip allowsease of use for the finest and minutest ofend product detail. The 18-series is perfect for general purpose die grinding in most applications,whilst the 28-series has even more powerfor maximum material removal in thedeburring of castings or large welds. The 18and 28-series are available in short and longmodels for easy accessibility. Both the 18 and 28-series range have aunique vibration-damping system that apartfrom reducing vibrations transferred to theoperator also virtually eliminates ‘chattering’of the burr on the work piece. The systemalso cuts burr consumption by at least 20%

Light deburring, die grindingand engraving

TC: Tungsten carbide tipped rotary burr.

HSS: High speed steel burrs. Use a ne cut burr for

hard and/or tough materials and a coarse cut burr

for stainless steel, soft materials or light alloy.

For mounted points, follow the recommendation

applicable to the particular mounted point.

The high speed LSF 07 should be used with tungsten

carbide burr only or with mounted points having the

corresponding max rpm.

LSF 07 can be used with up to 4 mm burr heads.

and provides a superior final surface finish.The speed governor inside the 18 and28-series tools is finely tuned to deliverhigh power performance while keeping toolweight low. The built-in silencer keeps thesound level for the LSF 18 below 75 dB(A)and under 78 dB(A) for the LSF 28.

Shaft diameterThe precision LSF 07 is supplied with a3 mm collet as standard. A 1/8” collet isavailable as an option. The LSF 18/28/38are fitted with a 6 mm collet as standard.Other sizes are available as optionalaccessories. Should the material you are working inspecify a burr head of 12 mm or more, it isrecommended you select an 8 mm shaftand collet tool combination.

Tool rpm selectionThe required rpm of the tool is dependent onthe diameter of the burr head, the material to be ground and the material composition ofthe burr, as detailed in the following table.

Hard Medium Softmaterial material material

Burr Hardened Mild steel, Wood, Brass,head Ø Steel Cast iron Plastic, Aluminium

Up to 3 mmTC 65 000 65 000 85 000

Up to 6 mmTC 43 000 43 000 43 000HSS – 20 000 30 000

Up to 12 mmTC 30 000 30 000 30 000HSS – – 20 000

Recommended rpm:


8/113

The short model is the best choice in mostcases. It is easily operated and convenient tohold.

The short model is the best choice in mostcases. It is easily operated and convenient tohold thanks to the collet guard. Vibrationdamped for low burr consumption.

Die grinder LSF 18 Angle die grinder LSV 18

An angle head model is often the best choicewhen grinding bottom areas in cavities andfor similar operations.

Die grinder LSF 18 extended

Use the extended model for internal grindingand for grinding in difficult-to-reach areas.The extension part is also vibration dampedfor low consumption of burrs.

Die grinder LSF 28

An angle head model is often the best choicewhen grinding bottom areas in cavities and forsimilar operations.

Angle die grinder LSV 28

Use the extended model for internal grindingand for grinding in difficult-to-reach areas.The extension part is also vibration dampedfor low consumption of burrs.

Die grinder LSF 28 extended

a) Not lubrication-free.E = Extended version, flexible spindle.

Rec. max dia of Sound

Max Tungsten Mount- Air consumption at Air level

free carbide ed Rec. inlet at free Ordering No.

speed burrs point Max output Weight Length max output free speed hose size thread speed with collet

Model r/min mm mm kW hp kg lb mm l/s cfm l/s cfm mm in BSP dB(A) 6 mm 1/4"

Die grinders – straight models. Lubrication-free

LSF18 S430-1a 43000 9 16 0.51 0.68 0.5 1.1 193 11.4 24 15.0 31.5 10 3/8 1/4 77 8423 1224 04LSF18 S430E-1a 43000 9 16 0.51 0.68 0.7 1.5 291 11.4 24 15.0 31.5 10 3/8 1/4 77 8423 1224 09LSF18 S300 30000 12 20 0.50 0.67 0.5 1.1 193 11.3 23.7 6.6 13.8 10 3/8 1/4 71 8423 1224 03 8423 1224 06LSF18 S300E-1 30000 12 20 0.50 0.67 0.7 1.5 291 11.3 23.7 6.6 13.8 10 3/8 1/4 71 8423 1224 08LSF18 S200 20000 12 20 0.40 0.54 0.5 1.1 193 9.6 20.1 3.5 7.4 10 3/8 1/4 67 8423 1224 02 8423 1224 05

LSF18 S200E-1 20000 12 20 0.40 0.54 0.7 1.5 291 9.6 20.1 3.5 7.4 10 3/8 1/4 67 8423 1224 07Angle grinders. Lubrication-freeLSV18 S200-1 20000 12 20 0.46 0.61 0.6 1.3 185 11 23 7 14.7 10 3/8 1/4 76 8423 0111 11LSV18 S120-1 12000 12 20 0.46 0.61 0.6 1.3 185 11 23 7 14.7 10 3/8 1/4 76 8423 0111 13LSV18 S080-1 8000 12 20 0.37 0.5 0.6 1.3 185 11 23 6.5 13.6 10 3/8 1/4 76 8423 0111 16

Rec. max dia of

SoundMax Tungsten Mount- Air consumption at Air level

free carbide ed Max Rec. inlet at free Ordering No. speed burrs point output Weight Length max output free speed hose size thread speed with collet

Model r/min mm mm kW hp kg lb mm l/s cfm l/s cfm mm in BSP dB(A) 6 mm

Die grinders – straight models

LSF28 S250a 25000 12 32 0.86 1.15 0.75 1.65 210 18.5 39.2 11.0 23.3 10 3/8 3/8 75 8423 1235 11LSF28 S250Ea 25000 12 32 0.86 1.15 1.25 2.75 335 18.5 39.2 11.0 23.3 10 3/8 3/8 75 8423 1235 60LSF28 S180a 18000 16 40 0.82 1.10 0.75 1.65 210 17.4 36.9 11.0 23.3 10 3/8 3/8 69 8423 1235 04LSF28 S180Ea 18000 16 40 0.82 1.10 1.25 2.75 335 17.4 36.9 7.0 14.8 10 3/8 3/8 69 8423 1235 05LSF28 S150a 15000 16 40 0.70 0.94 0.75 1.65 210 15.0 31.8 5.5 11.7 10 3/8 3/8 66 8423 1235 64LSF28 S150Ea 15000 16 40 0.70 0.94 1.25 2.75 335 15.0 31.8 4.3 9.1 10 3/8 3/8 66 8423 1235 61LSF28 S120a 12000 16 40 0.66 0.89 0.75 1.65 210 13.8 29.3 4.0 8.5 10 3/8 3/8 65 8423 1235 67Angle grinders

LSV28 S150 15000 16 40 0.68 0.91 1.15 2.53 250 17.0 36.0 8.3 17.6 10 3/8 3/8 78 8423 0125 54

ACCESSORIES INCLUDEDSpannerCollet 6 mmAir hose, air hose nipple and clampExhaust hose

ACCESSORIES INCLUDEDSpannerCollet 6 mmAir hose, air hose nipple and clampExhaust hose

7

a) Not lubrication-free. E = Extended version, flexible spindle.

M




9/113

8

Effective vibration dampening significantlyextends the working life of rotary burrs

and reduces your cost of operation whilealso improving comfort and control and asuperior surface finish.

Well balanced pencil grip for precisionapplications. The LSF 07 has a powerfulvane motor and yet a small grip size.

High speed die grinder LSF 07

a) With exhaust hose and in accordance with Pneurop Cagi test code for all tools.b) Ø 3 mm collet standard.c) Air hose and ErgoNIP included.

Optional accessories Service kits

Collets Ø Ordering No. Spindle extension Ordering No.

3 mm 4150 0081 00 Length 75 mm (3") 4150 0674 008 mm 4150 0074 00

1/8" 4150 0082 00

1/4" 4150 0076 00

1/8" for LSF 4150 1822 00

Unique vibration damping

Model Ordering No.

18-series 4081 0355 9028-series 4081 0130 90

LSF07 4081 0243 90


Max Tungsten Mount- Air consumption at Air level

free carbide ed Rec. inlet at free

speed burrs point Max output Weight Length max output free speed hose sizec thread speeda Ordering No.

Model r/min mm mm kW hp kg lb mm l/s cfm l/s cfm mm BSP dB(A) with colletb

LSF07 S850 88000 4 6 0.10 0.13 0.4 0.9 170 2.2 4.9 2.3 4.6 4.5 – 79 8423 1222 03

ACCESSORIES INCLUDED

Air hose and ErgoNIP 08 included Ø 3 mm colletand collet wrench. Exhaust with silencer.


10/113

9

Sanding, surface preparationand polishing

Peripheral speed of the disc

LSV 18 20–30 m/s * 40–60 m/s **

8 000 rpm dia. 40 – 60 mm dia. 80 mm12 000 rpm dia. 32 – 50 mm dia. 60 – 80 mm20 000 rpm dia. 20 – 30 mm dia. 38 – 60 mm

Applications Dry sanding and surface preparation, suchas removing handling marks and smoothingdown welds on car bodies and other sheetmetal objects. Rust and paint removal withfiber discs on sheet metal objects. Sandingand smoothing down the surface on wood,metal and non-ferrous objects and on glassfiber reinforced plastic. Polishing, grindlineremoving and reducing surface roughness.

The lubrication free models leave no oilmist in the exhaust air or on the sanded sur-face. They are therefore very suitable forhigh quality surface preparation in connec-tion with painting operations, etc.

Rpm selectionAlways follow the recommendations given by the manufacturer of the abrasive whichis used in each application. The recommen-ded working speed is usually between 50 –75% of the maximum permissible speed ofthe abrasive.

The following example is given for fiberdiscs, diameter 180 mm, by one manufac-turer of abrasives:

Material Recommended rpm

Steel and metal 5 300 – 6 300Stainless steel 3 200 – 4 200Aluminium, copper etc. 3 700 – 5 300

For LSV 18, the following speed and dimensionof the abrasive disc is recommended:

* coated abrasive, e.g. Speed-Lok from Norton.** nylon coated abrasive e.g. Roloc from 3M.

M




11/113

For polishing and surface conditioning withabrasive textiles e.g. Scotch-Brite andBear-Tex. Short and extended models.6 mm collet included.

For dry sanding and surface preparation. Supporthandle for two-hand operation and best control overthe sanding process.

Angle sander LSV 28

Die grinder/polisher LSF 28 ST


For light sanding, blending and grindlineconditioning with e.g. Roloc and Speed-Lokdiscs. Excellent grip over the angle head for perfect control.

Angle sander/polisher LSV 18

10

Sound

Max Rec. Height Air consumption at Rec. Air level free pad size Max over hose inlet at free

speed max dia Spindle output Weight Length spindle max output free speed size thread speed

Model r/min mm thread kW hp kg lb mm mm l/s cfm l/s cfm mm in BSP dB(A)a Ordering No.

With collet. Lubrication-free LSV18 S200-1 20000 50 – b 0.46 0.62 0.6 1.32 193 79 11.3 23.9 7.5 15.9 10 3/8 1/4 76 8423 0111 11

LSV18 S120-1 12000 75 – b 0.46 0.62 0.6 1.32 185 79 11.3 23.9 7.5 15.9 10 3/8 1/4 76 8423 0111 13

LSV18 S080-1 8000 75 – b 0.37 0.50 0.6 1.32 185 79 11.3 23.9 6.5 13.8 10 3/8 1/4 76 8423 0111 16

With threaded spindle. Lubrication-free

LSV18 S200 20000 50 1/4"-20 0.46 0.62 0.6 1.32 193 58 11.3 23.9 7.5 15.9 10 3/8 1/4 76 8423 0111 12

LSV18 S120 12000 75 1/4"-20 0.46 0.62 0.6 1.32 185 58 11.3 23.9 7.5 15.9 10 3/8 1/4 76 8423 0111 14

LSV18 S080 8000 75 1/4"-20 0.37 0.50 0.6 1.32 185 58 11.3 23.9 6.5 13.8 10 3/8 1/4 76 8423 0111 15

ACCESSORIES INCLUDEDAir hose nippleClampExhaust hose

Wrenches

a) LSV 18 measured with exhaust hose.b) Ø 6 mm collet.

ACCESSORIES INCLUDEDAir hose nippleClampExhaust hoseSupport handleWrenches

Sound

Max Rec. HeightAir consumption at

Rec. Air level

free pad size Max over hose inlet at free



Rotary sanders. Dry sandingLSV28 S060 6000 180 5/8"-11 0.73 0.98 1.5 3.2 265 87 16 33.9 7.3 15.5 10 3/8 3/8 73 8423 0125 30

LSV28 S040 4000 180 5/8"-11 0.62 0.83 1.5 3.2 265 87 15 31.8 4 8.5 10 3/8 3/8 72 8423 0126 22

LSV28 ST034 3400 180 5/8"-11 0.71 0.95 1.7 3.7 305 87 18 38.2 7.7 16.3 10 3/8 3/8 77 8423 0135 80

LSV28 S021 2100 180 5/8"-11 0.68 0.91 1.9 4.1 285 87 16 33.9 5.6 11.9 10 3/8 3/8 71 8423 0125 19

ACCESSORIES INCLUDEDSpannerCollet 6 mmAir hose, air hose nippleExhaust hose

a) LSV 28 measured with exhaust hose.

Rec. max dia of SoundMax Tungsten Mount- Air consumption at Air levelfree carbide ed Rec. inlet at free Ordering No.

speed burrs point Max output Weight Length max output free speed hose size thread speed with collet Model r/min mm mm kW hp kg lb mm l/s cfm l/s cfm mm in BSP dB(A) 6 mm

Lubrication-freeLSF28 ST030 3000 – – 0.67 0.90 1.16 2.55 275 18.0 38.2 8.6 18.2 10 3/8 3/8 73 8423 1235 63LSF28 ST030E 3000 – – 0.67 0.90 1.76 3.87 400 18.0 38.2 8.6 18.2 10 3/8 3/8 73 8423 1235 62LSF28 ST070a 7000 – – 0.76 1.02 1.16 2.55 275 18.9 40.1 12.4 26.3 10 3/8 3/8 75 8423 1235 66

LSF28 ST070Ea

7000 – – 0.76 1.02 1.76 3.87 400 18.9 40.1 12.4 26.3 10 3/8 3/8 75 8423 1235 65


12/113

Orbital sander LSO

For sanding in square corners and a moreaggressive finishing sanding.

Random orbital sander LST

Small and light weight sander with very low vibrationlevels. Interchangeable grip over handle for improvedhandling. Choose between different pad sizes, orbitaldiameters type of suction systems to find the optimalsolution for every application.


11

ACCESSORIES INCLUDEDPad for velcro back paperU-wrench for pad changeAir hose nippleDust hose and bag (LST 21)Large and small grip cover

Sound

Max Rec. Air level free Orbit Max Air consumption hose inlet at free

speed Pad size dia output Weight Height Length at free speed size thread speed

Model r/min mm mm kW hp kg lb mm mm l/s cfm mm BSP dB(A) Ordering No.

Standard model. Lubrication-free

LST20 R650 12000 150 5 0.2 0.27 0.85 1.85 83 127 8 17 8 1/4 76 8423 0361 73Extraction model – self suction. Lubrication-free

LST21 R650 12000 150 5 0.2 0.27 0.85 1.85 83 133a 8 17 8 1/4 85 8423 0361 74Extraction model – central suctionb. Lubrication-free

LST22 R650 12000 150 5 0.2 0.27 0.85 1.85 83 133a 8 17 8 1/4 78 8423 0361 75

Sound

Max Rec. Air level

free Orbit Max Air consumption hose inlet at free

speed Pad size dia output Weight Height Length at free speed size thread speed

Model r/min mm mm kW hp kg lb mm mm l/s cfm mm BSP dB(A) Ordering No.

Standard model. Lubrication-free

LSO30 S070-3 7000 93x170 5 0.3 0.4 1.6 3.5 125 185 7.5 16 8 1/4 80 8423 0360 16LSO30 H070-3 7000 93x170 5 0.3 0.4 1.7 3.7 125 285 7.5 16 8 1/4 81 8423 0360 24

ACCESSORIES INCLUDEDBase padPerforating plateHose nipple for 8 mm hose

* Required suction capacity 250 m3 /h.

a) 186 mm (7.3") included suction hose connector.b) Required air flow 60 m3 /h or 35 cfm.All data at 6.3 bar.

H = With handle.S = Without handle.All data at 6.3 bar.

Model Description Ordering No.

LSV28, 5/8" Backing pad 4150 1962 81and M14 spindleØ 180 mm

Pin key for above pad 4080 1169 00

LSV28 S060, Dust extraction kit* 3780 4007 90LSV28 S040

LSO30-3 Velcro pad, 4112 0787 01 Ø 93x170 mm

LST20 Velcro pad, Ø 150 mm 4112 1235 00

LST21, LST22 Velcro pad, Ø 150 mm 4112 1234 00

Model Ordering No.

LSV18 4081 0366 90LSF/LSV28 4081 1030 90LSO 4081 0131 90LST 4112 1300 90

M


M a t e r i a

l r e m o v a l t o o l s


13/113

12

Applications Heavy deburring, light trimming of welds,hollow grinding and internal cleaning ofcastings, repair grinding of material cracks prior to welding, bevelling, weld rootcleaning , where the object puts a limit tothe size of tool from an access point ofview or where the material penetration

needs to be precise.

The toolsAngle grinders are used with depressedcentre wheels and cutting discs, 80 – 125 mm(3 – 5") diameter. For best control, use thesupport handle for a two-hand grip. For best

access and reach, the tool can be used withoutthe support handle for one-handed operationtasks. Straight grinders are used with cone and plug

Heavy deburring, trimmingand internal grinding

Material Recommended rpm

High alloy steel 12 000 – 25 000Stainless steel, cast iron 15 000 – 30 000Aluminium 12 000 – 30 000

The higher rpm value is a guide for usingtungsten carbide rotary burrs, with the lowerrpm values are typical for high-speed rotary burrs.

wheels for internal grinding operation. Theyare permitted to be used without any wheelguard to admit access. Mounted points, tungsten carbide burrsand the smaller mounted points are usedwith the most powerful die grinders alsowithout the need for a wheel guard. Therigid version of LSF 38 is well suited forthe use of mounted point abrasives.

Tool rpm selectionThe selection of the tool speed depends onthe shape of the burr, its diameter and thematerial to be ground. Usually it is the sizeof the area to be worked and degree ofaccessibility that the shape of the plug orcone wheel to be used. The manufacturer’srecommendations should always be followedwhen selecting wheel type. As a guide, a general purpose 12 mm burrhead has the following recommended rpmrange:


14/113

13

Die grinders for rotary burr and mounted points LSF 38

LSF 38 is vibration damped for maximum comfortand extended burr life with up to 20%. All modelshave rear exhaust.

For light grinding and small jobs in confinedspaces. For trimming and cleaning of weldswith depressed centre wheels or cut-off discs.

Angle grinders for depressed centre wheels LSV 18/28/38

Angle grinder with extended neck LSV 28

Max free Max wheel Max Height over Air consumption at Spindle Sound levelspeed dimensions output Weight spindle max power free speed thread at free speed

Model r/min mm in kW hp kg lb mm in l/s cfm l/s cfm UNF dB(A) Ordering No. LSV28 ST13-10E 13000 100 4 0.75 1 1.5 3.3 68 2.7 21.5 45 14.5 30 3/8”-24 75 8423 0125 29

a) DxTxH = Diameter x Thickness x Hole.b) For LSV 18/28/38 ST.c) Lubrication-free.

With wheel guard for disc –08 = Ø 75 mm–12 = Ø 115 mm

–13 = Ø 125 mm

For Sound

Max wheel Height Air consumption at Rec. Air level

free dia Max over hose inlet at free

speed DxTxHa Spindle output Weight spindle max output free speed size thread speed

Model r/min mm thread kW hp kg lb mm l/s cfm l/s cfm mm in BSP dB(A)b Ordering No.

LSV18 S170-08c 17000 80x7x10 UNF 3/8" 0.45 0.6 0.7 1.55 71 11.2 23 6.6 14 10 3/8 1/4 76 8423 0111 10LSV28 ST12-10 12000 100x7x16 3/8 0.75 1.0 1.7 3.7 80 17.4 36.9 7.5 15.9 10 3/8 3/8 75 8423 0125 14LSV28 ST12-12 12000 115x7x22 3/8 0.75 1.0 1.7 3.7 80 17.4 36.9 7.5 15.9 10 3/8 3/8 75 8423 0125 16LSV28 ST12-13 12000 125x7x22 3/8 0.75 1.0 1.7 3.7 80 17.4 36.9 7.5 15.9 10 3/8 3/8 75 8423 0125 17LSV38 ST12-125c 12000 125x7x22 M14 1.30 1.7 1.8 4.0 83 28 58 15 31 13 3/8 1/2 83 8423 0131 10

ACCESSORIES INCLUDEDWheel guardFlangesAir hose nipple, clampWrenchesExhaust hose setSupport handle

ACCESSORIES INCLUDEDSpanner

Collet 6 mmExhaust hose

An excellent choice whatever your grinding application.It covers the range where others don’t reach, from roughgrinding of welds and cleaning of castings to finesurface preparation and polishing – with a slimmer profile and a better reach.


R = Rigid model.

ACCESSORIES INCLUDEDFlangesOpen- end spannerPin keyGrease gunHose kit

M


M a t e r i a



Max Tungsten Mount-Air consumption at

Air level

free carbide ed Rec. inlet at free Ordering No.

speed burrs point Max output Weight Length max output free speed hose size thread speed with collet

Model r/min mm mm kW hp kg lb mm l/s cfm l/s cfm mm in BSP dB(A) 6 mm

Lubrication-freeLSF38 S250E-01a 25000 16 40 1.35 1.8 1.5 3.3 352 28 58 25 53 13 1/2 3/8 83 8423 1231 17LSF38 S180E-01 18000 16 40 1.35 1.8 1.5 3.3 352 28 58 15 31 13 1/2 3/8 81 8423 1231 16LSF38 S180E-01/R 18000 16 40 1.35 1.8 1.5 3.3 356 28 58 15 31 13 1/2 3/8 81 8423 1231 15LSF38 S150E-01/R 15000 16 40 1.25 1.7 1.5 3.3 356 24 50 13 27 13 1/2 3/8 80 8423 1231 14


15/113

Small-size vibration damped straight grinder

for 50 mm (2") straight wheels (48 m/s peri pheral speed).

14

Service kits

Straight grinder for straight wheels LSR 28

Optional accessories

Straight grinder for cone wheels and mounted points LSR 43

Sound

MaxAir consumption at

Air level

free Rec. inlet at free

speed Max output Weight Length max output free speed hose size thread speed

Model r/min kW hp kg lb mm l/s cfm l/s cfm mm in BSP dB(A) Ordering No.

LSR43 S150-30C 15000 1.0 1.3 2.1 4.6 503 23 49 10 21 13 1/2 1/2 87 8423 1432 33LSR43 S120-30 12000 0.9 1.2 2.0 4.4 438 20 42 7 15 13 1/2 1/2 84 8423 1432 24

Adapter for cone wheel thread

LSR28/38 LSR43CW S120-30

UNC/W 3/8" 4150 0318 00 4150 0943 00UNF 3/8" 4150 0318 01 4150 0943 01UNC 1/2" 4150 1357 00 4150 0944 00W 1/2" –– 4150 0942 00

UNC/W 5/8" 4150 0767 00 4150 0945 00

The CW model for cones or plugs with threaded bushing. LSR 43 with adapter* for cone and plugwheels with threaded bushing or collet chuck formounted points.* Optional

Straight grinder for cone wheels LSR 38

a) LSR 38 measured with exhaust hose (incl. accessories).LSR 38 CW indicates use for cone wheel or collet,thread M12x1 to be combined with adaptor for wheel thread.

ACCESSORIES INCLUDEDAir hose nipple and clampExhaust hoseWrenches

Collets LSF38 LSR43 S150-30C

6 mm 4150 1453 00 4150 1453 00*8 mm 4150 0706 00* 4150 0706 00

9 mm 4150 0765 00 4150 0765 00 10 mm 4150 0681 00 4150 0681 00

*Included as standard

Extension LSR43 S150-30C

L=75 mm 4150 0441 00 For the above extension, use collet 6 mm 4150 0222 00 collet 8 mm 4150 0325 00 collet 1/4" 4150 0223 00 collet nut 4150 0221 00

Sound

Max For Air level

free wheel dia.Air consumption at

Rec. inlet at free

speed DxTxHa Spindle Max output Weight Length max output free speed hose size thread speed


LSR28 S180-05 18000 50x13x10 UNC 3/8x42 0.82 1.09 1.86 4.09 340 19.8 42.0 7.3 15.5 13 3/8 1/2 76 8423 1325 04

Powerful straight grinder with collet formounted points, rotary burrs and cone wheels.Side exhaust.

a) DxTxH = Diameter x Thickness x Hole.b) LSR 28 measured with exhaust hose (incl accessories).

ACCESSORIES INCLUDEDWheel guard, size according to typeNut, flangesAir hose, air hose nipple and clampExhaust hoseWrenches

ACCESSORIES INCLUDEDLSR43 S150-30C:Collet keysAir hose nippleHose clamp

Sound

Max Air consumption at Air level

free Rec. inlet at free speed Max output Weight Length max output free speed hose size thread speed

Model r/min kW hp kg lb mm l/s cfm l/s cfm mm in BSP dB(A)a Ordering No.

Lubrication-free

LSR38 S150-CW 15000 1.25 1.7 1.5 3.3 320 24 50 13 27 13 3/8 1/2 80 8423 1232 31LSR38 S180-CW 18000 1.35 1.8 1.5 3.3 320 28 58 15 31 13 3/8 1/2 81 8423 1232 30

Model Ordering No.

LSF38 4081 0308 90 LSR38 4081 0311 90 LSV18 4081 0355 90 LSV28/LSR28 4081 0317 90 LSV38 4081 0309 90 LSR43 4081 0020 90


16/113

15

Heavy rough grindingand cutting off

ApplicationsCutting off raisers and ingot mold incastings, pipes, beams, profiles, stone andconcrete with cut-off wheels. The ALU-cutaccessories are specially developed forcutting-off aluminium.

Rough grinding , trimming and cleaning ofwelds, weld root grinding, fettling of cast-ings, bevelling, grinding in steel, cast iron,stone and concrete with depressed centrewheels.

Stock removal and flat grinding, grindingand cleaning of welds, castings, steel, stone

and concrete with cup wheels.

The toolsChoose the high power turbo grindersGTG 40 and GTR 40 for highest materialremoval rate. They are the most powerful

grinders in the world, yet small in size, for best accessibility in close quarters. Theyare also the ideal tools for grinding softmetals such as stainless steel and aluminium because they are lubrication free thus leavingno oil stains on the ground surface.

A unique design feature, the AutoBalancerreduces the vibration level by 50%. TheLSS 84/64 vertical grinders and the LSR 64straight grinders are of classic well-proven

design with a conventional vane motor.The straight grinders GTR 40 and LSR 64have an extended grip to provide extrareach to tackle any challenge.

Wheel diameter

Wheel type Ø 230 mm Ø 180 mm Ø 150 mm

Cutting-off Best reachwheels for cutting- off and

fewer wheel changes

Depressed Continous All roundcentre grinding grinding

Cup wheels Combine stock removal (when tilted) and surface finish (when

held flush with the surface),lasts longer

GTR and LSR Stock removal and internalStraight wheels grindingand cone wheels

Recommended wheel type dimension

M


M a t e r i a



17/113

16

Turbo grinder for straight wheels GTR 40

The extended design gives extra reach overlarge objects. Side exhaust that can be directed

to either side of the tool.

Turbo grinder for cut-off wheels, cup wheels and depressed centre wheels GTG 40

Extremely high removal rate and greataccessibility.

Turbo grinder GTG 21

Flow requirement 250 m3 /h.

a) For straight wheels.

Sound

Max For Air consumption at Air level

free wheel dia Rec. inlet at free


Model r/min mm thread kW hp kg lb mm l/s cfm l/s cfm mm in BSP dB(A) Ordering No.

Lubrication-free

GTR40 S085-15 8500 150x25x25 UNC 5/8x11 4.5 6.1 5.6 12.3 563 60 126 20 42 16 5/8 1/2 85 8423 2950 00GTR40 S072-13 7200 125x25x25 UNC 5/8x11 4.5 6.1 5.6 12.3 563 60 126 20 42 16 5/8 1/2 85 8423 2951 00GTR40 S060-15 6000 150x25x25 UNC 5/8x11 4.5 6.1 5.8 12.8 563 60 126 20 42 16 5/8 1/2 85 8423 2952 00

Max For Air consumption at Air Sound level

free wheel Height over Rec. inlet at free

speed dia Max output Weight spindle max output free speed hose size thread speed

Model r/min mm kW hp kg lb mm in l/s cfm l/s cfm mm in BSP dB(A) Ordering No.

For grinding and cutting

GTG40 F085-18 8500 180 4.5 6.1 3.8 8.4 128 5.0 60 126 20 42 16 5/8 1/2 85 8423 2900 10GTG40 F066-23 6600 230 4.5 6.1 4.0 8.8 128 5.0 60 126 20 42 16 5/8 1/2 85 8423 2910 10

a) Spindle thread: UNC 5/8". Length 23.5 mm.

Max For Height over Air consumption at Rec. Air Sound level

free wheelMax output Weight spindle max output free speed hose size

inlet at free

speed dia thread speed

Model r/min mm kW hp kg lb mm in l/s cfm l/s cfm mm in BSP dB(A) Ordering No.For grinding and cutting. Lubrication-free

GTG21 F120-13 12000 125 2.1 2.8 1.8 3.9 68 2.7 30 64 10 21 13 1/2 3/8 76 8423 2963 00GTG21 F085-18 8500 180 2.1 2.8 2.0 4.2 72 2.8 30 64 10 21 13 1/2 3/8 76 8423 2963 02

ACCESSORIES INCLUDEDWheel guard. Attachments flanges for grindingwheels 20–25 mm thick and with hole Ø 25 mm.Whip hose 0.7 m long, 16 mm dia complete withnipple and ErgoNIP 10. Gear box oil, one tube.

Key and spanner for wheel change.

Astonishing power-to-weight ratio. Highest possible material removal. Unbelievableremoval rate.

For cup wheels

GTG40 S060-C15a 6000 150 4.5 6.1 4.3 10.5 126 5.0 60 126 20 42 16 5/8 1/2 85 8423 2930 10

ACCESSORIES INCLUDEDAdjustable wheel guard. Support handle.Attachments flanges for 1.5–7 mm thick cut-offwheels and 2.5–8 mm thick depressed centre wheels.Whip hose 0.7 m long, 16 mm dia complete withnipple and ErgoNIP 10. Gear box oil, one tube.Hex key for wheel change.

ACCESSORIES INCLUDEDAdjustable support handle. Whip hose 0.7 m long,13 mm dia complete with nipple and ErgoNIP 10.Gear box oil, one tube. Adjustable wheel guard.Attachment flanges for 1–10 mm thick grindingwheels. Hex key for wheel change.


18/113

17

Service kits

Classic, well-proven design ensures maximumreliability. The cast iron cylinder ensuresa long service life.

Conventional grinder for cut-off, cup wheels and depressed centre wheels LSS 64/84


Flanges for GTR40 and LSR64 Ordering No.

Grinding wheel hole Ø 16 mm 4150 0619 00

(Thickness 20–32 mm) Ø 20 mm 4150 1650 00 Ø 32 mm 4150 0620 00 Spacer for cone wheel 4150 0787 00 Accessories for GTG40 Ordering No.

Starting handle with lever on the lower side Adaptor 4175 0161 00

Handle 4170 1157 92

A powerful grinder for straight wheels.Cast iron cylinder for long service life.

Conventional grinder for straight wheels LSR 64

a)For cup wheel.

a) DxTxH = Diameter x Thickness x Hole.b) For LSR 64 the sound level can be reduced 8–12 dB(A) by using a silencer (optional accessories).

ALU-cut accessories for LSV38 Ordering No.

Guard set 4112 1161 00

Cutting off disc Ø 125 mm, t=2.2 mm 4112 1164 00

Model Ordering No.

GTG21 4081 0220 90

GTG40 4081 0153 90 GTR40 4081 0153 91 LSS64 4081 0133 90 LSS84 4081 0136 90 LSR64 4081 0138 90

Sound

Max For Height Air consumption at Air level

free wheel Max over Rec. inlet at free

speed dia Spindle output Weight spindle max output free speed hose size thread speed


Vertical grinders

LSS64 S085-18 8500 180 5/8 2.6 3.5 4.7 10.4 201 50 106 13 28 16 5/8 1/2 86 8423 2641 38

LSS64 S060-C15a 6000 150 5/8 2.2 3.0 5.0 11.0 201 40 85 9 19 16 5/8 1/2 82 8423 2641 04

LSS84 S060-23 6000 230 5/8 3.8 5.1 6.0 13.2 217 65 138 17 36 19 3/4 1/2 88 8423 2840 26

ACCESSORIES INCLUDEDAttachment according to EN 68Wheel guardFlangeNutWrenches

ACCESSORIES INCLUDEDWheel guard, size according to type.Nut, flanges. Air hose nipple and clamp.Wrenches.

Sound

Max For Air level


Rec. inlet at free



Straight grinders

LSR64 S100-15 10000 150x25x25 UNC 5/8x55 2.9 4.0 5.8 2.8 535 53 112 26 55 16 1/2 5/8 88 8423 1640 55LSR64 S060-15 6000 150x25x16 UNC 5/8x55 2.3 3.1 5.4 11.9 535 41 87 11 23 16 1/2 5/8 82 8423 1640 22

M




19/113

18

Medium rough grindingand rough sanding

ApplicationFor general adjustment grinding, weld preparations and light cleaning of castingsusing bonded abrasives with depressed-centreor straight-sided wheels. Other applicationsinclude those that require a finer surfacefinish such as weld grinding, removal ofcasting scale and sand, or rough cleaninggrinding in soft materials with coarse gritfibre discs.

The toolsThe GTG 21 is the most compact, powerfuland efficient tool of its kind on the marketand is recommended for the full spectrum ofapplications. This third-generation turbinetool provides immense power and maintains

high rpm even under the heaviest loads. Withone of the highest power-to-weight ratiosavailable and weighing only two kilogramsit makes fast work of any grinding task. TheGTG 21 will quickly pay for itself due tothe labour savings that result from its high

productivity.There is also a range of vertical grinders

available to suit applications that haverestricted access, and general purpose vanegrinder models tailored to any workshopneeds. For the cleaning of castings, the LSRstraight grinders should be used with wheeldiameters of 100 or 125 mm, while theLSS 53 vertical grinder is designed for

coarse grit sanding with flap wheels.

The lubrication-free turbine grinders arealso popular for their capacity in roughsanding and grinding in soft materials such

as aluminium and bronze.

Tool rpm selectionBe sure to check that the grinder speedmatches and never exceeds the grinder wheel

specification. Rough sanding is performed at a speedwhich is usually lower than the maximum permissible speed of the fibre disc. Speeds

should be determined by the manufacturer’srecommendations. However, common speedsfor a 180 mm diameter disc are between5,300 to 6,300 rpm for fibre discs and between 3,700 to 5,300 rpm for flap discs.


20/113

The perfect tool for heavy-duty applications. An Autobalancerkeeps vibrations below 2.5 m/s2. High power, low weight andlow height over the spindle gives you the best productivityand accessibility.

For grinding in confined spaces with grinding wheeldiameter 125 mm, 5". The wheel guard is adjustablefor higher accessibility.

Angle grinder LSV 48

Angle grinder LSV 38

a) DxTxH = Diameter x Thicknes x Hole.

19

ACCESSORIES INCLUDEDWheel guard. Flange nut. Support handle.

Angle sander LSV 48

ACCESSORIES INCLUDEDAdjustable wheel guard. Wheel attachment flanges.Wrenches for flanges. Spindle lock. Support handle.Exhaust hose.

ACCESSORIES INCLUDEDAir hose nipple. Clamp. Support handle. Wrenches.

a) DxTxH = Diameter x Thicknes x Hole.b) For LSV 38 ST with exhaust hose.

Angle sander LSV 38

For rough sanding. Piped away rear exhaust,lubrication free, ideal for high quality surface preparation and sanding in e.g. aluminium andin stainless steel.

a) LSV 38 measured with exhaust hose. ACCESSORIES INCLUDEDAir hose nipple. Clamp. Exhaust hose.Support handle. Wrenches.

M



For Sound


free dia Max over

hose inlet at free



Lubrication-freeLSV38 ST12-125 12000 125x7x22 M14 1.30 1.7 1.8 4.0 83 28 58 15 31 13 3/8 1/2 83 8423 0131 11

Sound

Max Rec. Height Air consumption at Rec. Air level




Lubrication-free. Dry sanding

LSV38 S085 8500 180 5/8 1.30 1.7 1.5 3.3 217 96 28 58 15 31 13 1/2 3/8 83 8423 0130 69LSV38 S085-M14 8500 180 M14 1.30 1.7 1.5 3.3 217 96 28 58 15 31 13 1/2 3/8 83 8423 0130 72LSV38 S066 6600 180 5/8 1.20 1.6 1.5 3.3 217 96 24 50 13 27 13 1/2 3/8 83 8423 0130 73LSV38 S066-M14 6600 180 M14 1.20 1.6 1.5 3.3 217 96 24 50 13 27 13 1/2 3/8 83 8423 0130 77

For Sound


free dia Max over hose inlet at free



Lubrication-free

LSV48 SA120-13 12000 125x7x22 M14 1.9 2.5 2.5 5.5 78 36 76 17 36 16 5/8 1/2 89 8423 0132 07LSV48 SA085-18 8500 180x7x22 M14 1.9 2.5 2.7 5.9 78 36 76 17 36 16 5/8 1/2 89 8423 0132 06LSV48 SA066-23 6600 230x7x22 5/8"-11 1.9 2.5 2.9 6.4 82 36 76 17 36 16 5/8 1/2 89 8423 0132 08

The perfect tool for heavy-duty applications. An Autobalancerkeeps vibrations below 2.5 m/s2. High power, low weight andlow height over the spindle gives you the best productivityand accessibility.

Sound

Max Rec. Height Air consumption at Rec. Air level



Model r/min mm thread kW hp kg lb mm mm l/s cfm l/s cfm mm in BSP dB(A) Ordering No.

Lubrication-free. Dry and wet sanding LSV48 SA085 8500 180 5/8 1.9 2.5 2.3 5.1 310 78 36 76 17 36 16 5/8 1/2 83 8423 0132 02LSV48 SA085-M14 8500 180 M14 1.9 2.5 2.3 5.1 310 78 36 76 17 36 16 5/8 1/2 83 8423 0132 03LSV48 SA066 6600 180 5/8 1.9 2.5 2.3 5.1 310 78 36 76 17 36 16 5/8 1/2 83 8423 0132 00LSV48 SA066-M14 6600 180 M14 1.9 2.5 2.3 5.1 310 78 36 76 17 36 16 5/8 1/2 83 8423 0132 01


21/113

20

Service kitsOptional accessories

Turbo sander GTG 21/40

The sander version of the turbine grinderintended for 180 and 230 mm (7 and 9") fibrediscs.

Model Ordering No.

LSS53 4081 0132 90 LSV38 4081 0309 90 LSV48 4081 0312 90 GTG21 4081 0220 90 LSR43 4081 0020 90 LSR48 4081 2023 90 GTG40 4081 0153 90

Backing pad GTG40 GTG21 LSV38

180 mm (7") 4170 1192 90 4170 1192 90 4170 0757 80* 180 mm (7") 4170 0756 80** 230 mm (9") 4170 1193 90

* stiff type up to grit 50. ** flexible type for grit 60 and finer.

Straight grinder LSR 43/48

Powerful and robust straight cone wheel grinder for high removal rate inheavy-duty applications. Side exhaust and possibility to use with silencer.

Sound

Max For Air level


Rec. inlet at free



LSR43 S090-10 9000 100x25x13 UNC 1/2x49 0.8 1.1 2.4 5.3 438 18 38 5 11 13 1/2 1/2 81 8423 1430 18LSR48 S120-13b 12000 125x25x16-25 UNC 5/8x42 1.8 2.4 3.6 7.9 482 30 64 13 28 16 5/8 1/2 80 8423 1430 06

ACCESSORIES INCLUDED LSR 48Wiphose. Hook wrench. Pin keyFlanges, 1/2 spindle, H dia. 13/16/20/25 mm 5/8 spindle, H dia. 16/20/25 mm

a) UNC 5/8"–11 spindle.b) For wire brush, Ø 230 mm for fibre disc.Flow requirement 250 m3 /h.

Max ForHeight over Air consumption at Rec.

Air Sound level

free wheelMax output Weight spindle max output free speed hose size

inlet at free

speed dia thread speed

Model r/min mm kW hp kg lb mm in l/s cfm l/s cfm mm in BSP dB(A) Ordering No.

For sanding

GTG21 S085a 8500 180 2.1 2.8 1.6 3.5 80 3.1 30 64 10 21 13 1/2 3/8 76 8423 2963 05GTG21 S085 M14 8500 180 2.1 2.8 1.6 3.5 80 3.1 30 64 10 21 13 1/2 3/8 76 8423 2963 07GTG21 D120 12000 180 2.1 2.8 1.6 3.5 92 3.6 30 64 10 21 13 1/2 3/8 76 8423 0800 00GTG21 D085 8500 180 2.1 2.8 1.6 3.5 92 3.6 30 64 10 21 13 1/2 3/8 76 8423 0800 01For wire brush and sanding

GTG40 S060 6000 140b 4.5 6.1 3.6 7.9 132 5.2 60 126 20 42 16 5/8 1/2 85 8423 2930 00

ACCESSORIES INCLUDED GTG 21

Adjustable support handle. Whip hose 0.7 m long,13 mm dia complete with nipple and ErgoNIP 10.Gear box oil, one tube.

ACCESSORIES INCLUDED GTG 40Adjustable wheel guard. Support handle.Attachments flanges for 1.5–7 mm thick cut-offwheels and 2.5–8 mm thick depressed centrewheels. Whip hose 0.7 m long, 16 mm dia completewith nipple and ErgoNIP 10. Gear box oil, one tube.Hex key for wheel change.

A light-weight but yet powerful vertical sander/grinderwith built-in silencer. For sanding with 180 mm fibrediscs and flap discs, or with a guard for depressedcentre wheel 180 mm.

Vertical sander/grinder LSS 53

Sound

Max Rec. Air consumption at Air level

free pad size Max Rec. inlet at free

speed dia Spindle output Weight Height max output free speed hose size thread speed


Rotary sanders. Vertical type

LSS53 S060 6000 180 5/8 1.2 1.6 2.3 5.1 180 24 51 7 15 13 1/2 1/2 76 8423 2530 23

ACCESSORIES INCLUDEDAttachment according to EN 68.Wheel guard. Flange.Nut. Wrenches.

Sound

Max For Height Air consumption at Air level free wheel Max over Rec. inlet at free

speed dia Spindle output Weight spindle max output free speed hose size thread speed


Vertical grinders

LSS53 S085-18 8500 180 5/8 1.4 1.9 2.9 6.4 180 27 57 10 21 13 1/2 1/2 79 8423 2530 72

a) DxTxH = Diameter x Thicknes x Hole.b) Lubrication-free.


22/113

21

Brazor Mark II electric grinders

ApplicationsThe new Brazor range takes care of all roughgrinding and cutting off applications. Themobile grinding system is successfully usedin all types of industries. The small angle head on Brazor grindersoffers greater cutting depth and enables youto use the maximum output of the grindingwheel.

Brazor Mark IIThe Brazor Mark II is equipped with acompact, energy efficient G71 motor providing matchless power.

90% of the consumed energy is trans-mitted to the spindle, making Brazor oneof the most cost efficient solutions.

The motor is completely sealed inside themotor housing to prevent external dust fromadhering to the motor and causing failure.An active cooling process over the externalcooling fins reduces tool temperature. The integrated autobalancer reducesvibration level. This feature, together withthe angle design of the rear handle, meansall Brazor models offer excellent tool

ergonomics.

PU81The mobile PU81 converter feeds the G71motor with maximum power to finish the job as quickly as possible. The grindingsystem can easily be connected to the 230Vsocket and is ready to be usedwithin a couple of seconds.

Integrated service indicatorHigh and unpredictable tool repair costsare now history.

No matter how much power is takenfrom the tool, it will make sure it getsthe service it needs to ensure long term productivity.

Based on its operating history, theservice indicator signals about the needfor service, the machine stops and the red button on top of the PU81 lights up. Afterservice message is confirmed by pressingthe red button, the machine ceases tofunction until service has been performed.

M




23/113

22

Power unit PU81

The top of the PU81 features a red lamp andservice button. Before service is required, the

tool stops and the red lamp lights up, warningthe operator that it is time for service.

By pressing the lamp, the operator hasacknowledged that the tool requires service;however, the operator is allowed to continueusing the tool to prevent unnecessary downtime.If this message is repeatedly ignored, thegrinder finally stops and cannot be run untilserviced.

The power unit connects to the 230V power drop and ensures that yourBrazor tool is supplied with enough power at all times to keep productivity at maximum.

The PU81 is ruggedly designed for survival in the toughestenvironments. Seals prevent penetration of dust and dirt. A built-inGround Fault Interrupter (GFI) will ensure electrical safety. The lowweight of the PU81, combined with a 2, 5, 10 or 20 m tool cable, ensuresthat the operator is free to move the system to wherever needed.

Service indicator Tool cables

a) Power net cable included.

Brazor electric grinder ESV G71

The mobile Brazor system offers high productivityand a cost-efficient solution for grinding and cuttingapplications. Electronic rpm control at rated speedensures optimum removal rate.

Max Weight Sound

Max free For out put without Height over level

speed wheel dia kW support handle Length Width spindle at free speed Outgoing

Model r/min mm peak cont. kg lb mm mm mm dB(A) spindle Ordering No.

For grinding and cutting

ESV G71 F120-13 12000 125 >3 2.3 2.8 6.2 350 65 55 81 M14 8433 5001 00ESV G71 F085-18 8500 180 >3 2.3 2.9 6.4 350 65 55 81 Internal 8433 5000 00ESV G71 F060-23 6000 230 >3 2.3 3.5 7.7 375 85 60 81 Internal 8433 5002 00For sanding

ESV G71 S060 6000 180 >3 2.3 3.2 7.0 375 85 83 81 5/8 8433 5003 00

ACCESSORIES INCLUDEDAdjustable wheel guard, support handle,attachment flanges for grinding and cutting

wheels, key for wheel change.Backing pad with ribbed surface for coolerprocess (for ESV G71 S060).

Length Ordering No.

2 m 3608 0250 05 5 m 3608 0250 05 10 m 3608 0250 10 20 m 3608 0250 20


Leather cable cover

Length Ordering No.

2 m 3608 0440 02 5 m 3608 0440 05 10 m 3608 0440 10 20 m 3608 0440 20

Length Width Height Weight Power

Model mm mm mm kg uptake Ordering No.

PU81a 350 200 200 10 1 phase 230 V 8433 5100 00


24/113

23

Weld flux removal.Multi purpose scaling

Applications – Weld fluxremovalFettling welds from flux and spatter.General scaling operations.

The tools Modern welding methods generate slag thatis easily removed and almost no spatter. Inthese applications RVM 07B is the rightchoice. It has power enough to do the job,very low noise and is vibration damped

below 2.5 m/s2

. The standard chisel delive-red with the tool is carbide tipped for a longservice life. The tool is also equipped withclean blowing capacity.

For heavy slag chipping and tougher scaling the conventional scaler RRC 13and RRC 13B with a blowing function arethe preferred models. These tools have theright power for this type of job and a sturdyreliable design. The gripping diameter isonly 45 mm inclusive the throttle lever.They also have a low vibration level forconventional models.

Applications – Rust and

paint removalIndustrial maintenance. Shipyards. On boardships and offshore rigs.

The toolsFor lighter jobs the needle scaler RRC I3is the ideal tool. Needle sets of differentshapes and material are available to suitmost operations. For tougher jobs, i.e. removal of deepseated rust or thick layers of painting, therust scalers RP 1 / RP 3 are the most effect-ive equipment. The carbide tipped bitsensure a quick material removal and avery long service life.

M




25/113

24

Medium duty jobs. Small and handy tool.

Needle scaler RRC 13N

Piston scaler RP 1/RP 3

Scaler RVM 07B

Very low noise and vibration figures.Reliable, long life design. Carbide-tipped chisel.The tool is equipped with a clean blowing device.

Effective, durable, easy to use. RRC 13B isequipped with a clean blowing device.

Scaler RRC 13/13B

Air Weight consumption Hose size Blows Length Air inlet

Model Hz mm kg lb l/s cfm mm in BSP Ordering No.

RP1 69 485 2.0 4.4 3.2 6.8 10 3/8 3/8 8425 0301 06RP3 69 515 3.9 8.6 9.6 20.3 10 3/8 3/8 8425 0301 14

Energy Air

Piston dia Stroke per blow Weight consumption Hose size Blows Length Air inlet

Model Hz mm in mm in J ft lb mm kg lb l/s cfm mm in BSP Ordering No.

RRC13 73 15 0.6 35 1.4 1.4 1.0 221 1.4 3.1 4.0 8.0 10 3/8 3/8 8425 0101 30RRC13B 73 15 0.6 35 1.4 1.4 1.0 231 1.6 3.5 4.0 8.0 10 3/8 3/8 8425 0101 33

ACCESSORIES INCLUDEDHose fittingScaling chisel

ACCESSORIES INCLUDEDHose fittingNeedle set (steel)

ACCESSORIES INCLUDEDHose fittingFlat carbide tipped chisel 10x120 mm

ACCESSORIES INCLUDEDHose fittingFour-point carbide bit, length 55 mm

Weight incl.

Air standardconsumption

Hose size

Air Blows Length chisel inlet

Model Hz mm kg lb l/s cfm mm in BSP Ordering No.

RVM07B 100 273 1.7 3.8 3.8 8.1 6.3 1/4 1/4 8425 0105 25

Energy Air

Piston dia Stroke per blow Weight consumption Hose size Blows Length Air inlet

Model Hz mm in mm in J ft lb mm kg lb l/s cfm mm in BSP Ordering No.

RRC13N 73 15 0.6 35 1.4 1.4 1.0 352 1.9 4.2 4.0 8.0 10 3/8 3/8 8425 0101 36

For the most heavy duty jobs on deeply corrodedsteel surfaces, rust and paint removal. Four point

carbide bit. RP 3 has three percussive heads.


26/113

25

RVM07B (06/06B) Ordering No.

0.7 m rubber whip hose complete withErgoNIP 10 connector 8202 1180 42

Flat chisel Carbide 10 x 120 mm 3085 0321 00 Steel 10 x 120 mm 3085 0325 00 Carbide 20 x 120 mm 3085 0345 00 Steel 20 x 120 mm 3085 0346 00

Wide chisel Carbide 35 x 120 mm 3085 0322 00 Steel 35 x 120 mm 3085 0327 00

RRC13/13B Ordering No.

0.7 m rubber whip hose complete with

ErgoNIP 10 connector 8202 1180 44

Alt. all steel retainer 3510 0245 80

Hand guard 3510 0246 90

Silencer 3510 0366 80

Square 13 mm shank chisels for RRC13

Blank 15 x 200 mm 3085 0020 01

Flat chisel 15 x 165 mm 3085 0227 00

15 x 200 mm 3085 0227 01

Wide flat chisel 35 x 165 mm 3085 0032 00

Angle scraper chisel 35 x 165 mm 3085 0176 00

35 x 200 mm 3085 0176 01

55 x 165 mm 3085 0333 00

Scaling chisel 15 x 155 mm

3085 0018 00

15 x 200 mm 3085 0018 02

15 x 300 mm 3085 0018 01

RRC13N Ordering No.



Needle sets of 19 needles, length 100 mm

Application

Steel, standard Multi purpose 3510 0221 90

Steel, flat ends 3510 0227 90

Stainless, flat ends Work on stainless 3510 0228 90

steel

Beryllium copper Spark resistant 3510 0229 90

flat ends

RP1 and RP3 Ordering No.

Vibration dampedsupport handle 3550 0079 80




Model Ordering No.

RVM07B 4081 0148 90RRC13/13B 4081 0149 90RRC13N 4081 0149 90

M




27/113

26

ApplicationsGeneral chipping and multipurpose ”chisel-ing” in heavy industrial use. Fettling of

castings in foundries. Offshore and ship-yard applications.

The tools Efficient. For best effectivity, choose toolswith a high power-to-weight ratio. RRF21/31 have an excellent material removalrate. Well proven design. Use simple and well proven design for a long trouble free toollife. The conventional RRC 22 – 75 rangemodels, which have forged steel handles,are basic versions with excellent handling

and reliability. Vibration damped chippers are easy onyour operators. The RRF and RRD modelsare vibration damped.

Chipping

Practical hintsTo prevent injury from a shot out or flying

chisel:• Always use a retainer.• Inspect the retainer for wear or damage

daily.• Remove inserted tool when work is over.• When finishing a job, disconnect the tool

from air supply.• Before changing accessories, chisel or

die, disconnect from air supply.

Do not perform idle blowswith a hammer• They will cause high internal stresses

and shorten the service life of the tool.• Note the risk of shooting out the chisel,die or punch if the retainer is not in order.

Use personal protectiveequipment

• Always wear eye protection. • To prevent gradual loss of hearing,

wear ear protection. • Protect your fingers with working

gloves.


28/113

27

a) Effective piston dia 19 mm, 0.75 in.b) Effective piston dia 21.5 mm, 0.85 in.c) Spline.d) Integrated hose barb.

-11: Guided models.

Light weight and very low vibration.

Chipper RRD 37/57

a) ISO.

High power to weight. Compact design.Vibration damped.

Basic design and long service life.

Conventional chipper RRC 22/34/65/75

Chipping hammer RRF 21/31

a) ISO.

b) Integrated hose barb.

ACCESSORIES INCLUDEDChisel retainer and a hose fitting.


Chisel retainer and hose fitting.

Energy Air Piston dia Stroke per blow Weight Bushing consumption Hose size Blows Length Air inlet

Model Hz mm in mm in J ft lb mm kg lb mm in l/s cfm mm in BSP Ordering No.Chipping hammers vibration damped

RRF21-01 57 18 0.7 33 1.3 2.0 1.5 245 1.75 3.3 12.7a 0.50 6.5 13.8 10.0 3/8 3/8 8425 1104 05RRF31-01 38 22 0.9 43 1.7 4.4 3.2 265 2.5 5.3 12.7a 0.50 7.5 15.9 10.0 3/8 3/8 8425 1104 15

ACCESSORIES INCLUDEDFlat chiselSilencer completeHand gripKey


Model Hz mm in mm in J ft lb mm kg lb mm in l/s cfm mm in BSP Ordering No.

Chipping hammers vibration damped

RRD37-11 35 27/19a 1.1/0.8 70 2.8 6.8 5.0 418 3.0 6.6 17.3c 0.68 7.2 15.3 12.5 1/2 speciald 8425 1101 22RRD57-11 31 28/18b 1.1/0.8 92 3.6 9.3 6.9 458 3.4 7.5 17.3c 0.68 9.5 20.1 12.5 1/2 speciald 8425 1103 20


Model Hz mm in mm in J ft lb mm kg lb mm in l/s cfm mm in BSP Ordering No.

Chipping hammers including chisel retainer

RRC22F-01 62 15 0.6 52 2.0 2.7 2.0 260 2.2 4.9 12.7a 0.50 6.2 13.1 10 3/8 3/8 8425 0202 22RRC34B-01 45 24 0.9 67 2.6 5.5 4.1 330 4.5 9.9 17.3a 0.68 8.0 14.0 12.5 1/2 specialb 8425 0212 53RRC65B-01 40 29 1.1 50 2.0 10.0 7.3 335 5.9 13.0 17.3a 0.68 10.8 22.9 12.5 1/2 specialb 8425 0225 33

RRC75B-01 30 29 1.1 75 3.0 16.0 11.8 390 6.5 14.3 17.3a

0.68 14.0 29.6 12.5 1/2 specialb

8425 0225 58

-01: Guided models.

M


M a t e r i a



29/113

28

RRF21-01 Ordering No.

Open wire retainer (for wide chisels) 3512 0290 90

RRF31-01 Ordering No.

Open wire retainer (for wide chisels) 3512 0305 90

RRF21/31 and RRC22 Ordering No.



RRF21/31 Ordering No.

Power regulator 3512 0273 80

RRC34 – RRC75 Ordering No.



RRD37/57 Ordering No.



A range of chisels with ISO hex 12.7 mm

shank for RRF21/31-01 and RRC22-01 Ordering No.

Blank 13 x 200 3085 0182 00

13 x 350 3085 0182 01

Flat chisel 13 x 200 3085 0183 00

Sharp chisel 15 x 200 3085 0170 00

35 x 300 3085 0170 01

Angle scraper chisel 30 x 200 3085 0262 00

Plate cutting chisel 16 x 200 3085 0173 00

Guided 17.3 mm chisels Ordering No. Ordering No.

RRD-tools RRC-tools

(spline) (hex)

Chisel blank 22 x 335 3085 0242 00 3085 0220 00

22 x 560 3085 0242 01 3085 0220 01

Flat chisel 22 x 200 3085 0236 00 3085 0221 00 22 x 335 3085 0236 01 3085 0221 01

Wide flat chisel 50 x 335 3085 0250 00 3085 0235 00


Model Ordering No. RRF21-01 4081 0150 90RRF31-01 4081 0151 90RRC34 – RRC75 4081 0145 90


30/113

29

Drilling

Practical hints

• Always use the right speed for thedrill bit size.

• For multi-pupose drilling alwayschoose a drill with high power for best result.

• Use sharp high quality drill bitsfor easy drilling and good result.

• Use short drill bits for easieroperation. Bigger holes than8 – 10 mm, pre-drill the hole.

ApplicationsThe Atlas Copco drills will give you anoptimal solution for hand-held drilling inall kinds of material with holes rangingfrom 1 – 50 mm. Thanks to the wide rangeyou will always be able to find a drill withsuitable power and speed.

The toolsThe ergonomically designed grip and perfect balance ensure efficient operation with aminimum of strain and gives less fatigue tothe operator. The high power-to-weight ratiomeans maximum stock removal in theshortest possible time. Every Atlas Copco

drill is designed to use less air and is solidly built to ensure a long service life. The drillsare lubrication-free and have a wide rangeof accessories.

Many features• High power-to-weight ratio combined

with excellent power-to-air consumptionratio.

• Ergonomic design makes the tools easyto work with.

• Wide range of tools and accessories.• Lubrication-free.

M


M a t e r i a



31/113

30

High power – low air consumption. Efficient,lubrication-free motor ensures reliability andlong life. Comfortable one or two handed grip.

Pistol grip drill LBB 16/26/36/37

Chuck Air consumption Air Sound level Free capa- Weight at free speed Hose size inlet at free Without chuck speed city thread speed With chuckModel r/min mm kg lb l/s cfm mm in BSP dB(A) Ordering No. Model Ordering No.

Non-reversible drills with air supply through handle

LBB16 EPX-200a 20000 6.5 0.6 1.2 9.5 20.0 6.3 1/4 1/4 78 8421 0108 82 200-U 8421 0108 63LBB16 EPX-060a 6000 6.5 0.6 1.2 9.5 20.0 6.3 1/4 1/4 78 8421 0108 52 060-U 8421 0108 53LBB16 EPX-045a 4500 6.5 0.6 1.2 9.5 20.0 6.3 1/4 1/4 78 8421 0108 42 045-U 8421 0108 43LBB16 EPX-033a 3300 6.5 0.6 1.2 9.5 20.0 6.3 1/4 1/4 78 8421 0108 32 033-U 8421 0108 33LBB16 EPX-024a 2400 6.5 0.6 1.2 9.5 20.0 6.3 1/4 1/4 78 8421 0108 22 024-U 8421 0108 23LBB16 EPX-010b 1000 10.0 0.7 1.5 9.5 20.0 6.3 1/4 1/4 78 8421 0108 12 010-U 8421 0108 03LBB16 EPX-005b 500 10.0 0.7 1.5 9.5 20.0 6.3 1/4 1/4 78 8421 0108 08 050-U 8421 0108 09LBB26 EPX-060a 6000 8 0.69 1.5 14.5 31.8 10.0 3/8 1/4 80 8421 0500 14 060-U 8421 0500 15LBB26 EPX-045a 4500 8 0.69 1.5 14.5 31.8 10.0 3/8 1/4 80 8421 0500 12 045-U 8421 0500 13LBB26 EPX-033a 3300 8 0.69 1.5 14.5 31.8 10.0 3/8 1/4 80 8421 0500 10 033-U 8421 0500 11LBB26 EPX-026ad 2600 8 0.79 1.7 14.5 31.8 10.0 3/8 1/4 80 8421 0500 08 026-U 8421 0500 09LBB26 EPX-019a 1900 10 0.79 1.7 14.5 31.8 10.0 3/8 1/4 80 8421 0500 24 026-U 8421 0500 25LBB26 EPX-013ab 1300 10 0.79 1.7 14.5 31.8 10.0 3/8 1/4 80 8421 0500 06 013-U 8421 0500 07LBB26 EPX-007b 700 13 0.82 1.8 14.5 31.8 10.0 3/8 1/4 80 8421 0500 04 007-U 8421 0500 05LBB26 EPX-005b 500 13 0.82 1.8 14.5 31.8 10.0 3/8 1/4 80 8421 0500 02 005-U 8421 0500 03LBB26 EPX-003b 300 13 0.82 1.8 14.5 31.8 10.0 3/8 1/4 80 8421 0500 00 003-U 8421 0500 01LBB36 H200a 20000 6.5 1.0 2.2 16.5 34.9 10.0 3/8 3/8 81 8421 0408 55 -H200U 8421 0408 53LBB36 H060a 6000 6.5 1.2 2.5 16.5 34.9 10.0 3/8 3/8 81 8421 0408 49 -H060U 8421 0408 47LBB36 H033a 3300 10.0 1.2 2.5 16.5 34.9 10.0 3/8 3/8 81 8421 0408 41 -H033U 8421 0408 39LBB36 H026a 2600 10.0 1.2 2.5 16.5 34.9 10.0 3/8 3/8 81 8421 0408 33 -H026U 8421 0408 31LBB36 H013a 1300 10.0 1.5 3.3 16.5 34.9 10.0 3/8 3/8 81 8421 0408 15 -H013U 8421 0408 13LBB36 H007b 700 13.0 1.6 3.5 16.5 34.9 10.0 3/8 3/8 81 8421 0408 07 -H007U 8421 0408 05LBB36 H005b 500 – 1.2 3.3 16.5 34.9 10.0 3/8 3/8 81 – -H005U 8421 0408 03LBB37 H230 23000 6.5 1.0 2.2 20.5 44.0 10.0 3/8 3/8 83 8421 0608 03 -H230U 8421 0608 18LBB37 H065 6500 6.5 1.2 2.5 20.5 44.0 10.0 3/8 3/8 83 8421 0608 11 -H065U 8421 0608 17LBB37 H037 3700 10.0 1.2 2.5 20.5 44.0 10.0 3/8 3/8 83 8421 0608 13 -H037U 8421 0608 16LBB37 H015 1500 10.0 1.5 3.3 20.5 44.0 10.0 3/8 3/8 83 8421 0608 05 -H015U 8421 0608 15LBB37 H006 600 – 1.2 2.5 20.5 44.0 10.0 3/8 3/8 83 – -H006U 8421 0608 14

LBB 16 EPX 340 W

LBB 26 500 W

LBB 36 700 W

LBB 37 820 W

ACCESSORIES INCLUDEDChuck, chuck key, hose nipple. LBB 16 and -36/37with suspension yoke and with chuck guardwhere possible. 16, 26 and -36/37-models havea 3/8" -24 UNF spindle thread.LBB 36 H005 and LBB 37 H006 has a 1/2" thread.

a) Including chuck guard.b) Including support handle.c) 79 dB(A) with silencer set 4112 0863 80.d) Also available in explosion proofcertified

versions.

Selection guide

Different materials requiredifferent cutting speeds. Thecutting speed is determined by thetool spindle speed and the drill bitdiameter. The cutting speedincreases with increased drill bitdiameter. Drilling with highercutting speed than recommended

can result in faster drill bit wearand lower hole quality. Forexample: if the material is castiron and the drill bit diameter is3 mm the right tool speed is2,400 rpm.

Material/cutting speed

Aluminium Wood

Titanium Mild steel Alloy steel Cast iron and bronze and board Composite

20-30 5-15 15-20 50-80 80-150 50-100

Model m/min m/min m/min m/min m/min m/min

LBB16 200 – – – – 1.0 - 2.0 1.0 - 4.0 1.0 - 4.0EP/EPX 060 – – – – 1.0 - 5.0 2.0 - 5.0 2.0 - 5.0 045 – 1.0 - 2.5 – 1.0 - 2.0 2.0 - 8.0 4.0 - 10.0 4.0 - 10.0 033 – 2.0 - 4.0 1.0 - 1.5 1.5 - 2.5 5.0 - 10.0 5.0 - 12.0 5.0 - 12.0 024 – 2.5 - 5.0 1.0 - 2.0 2.0 - 4.0 – – – 010 – 6.0 - 8.0 1.5 - 5.0 5.0 - 8.0 – – –

007 3 6.0 - 8.0 1.5 - 5.0 5.0 - 8.0 – – – 005 5 6.0 - 8.0 1.5 - 5.0 5.0 - 8.0 – – –

LBB26 060 – 1.0 - 2.0 – – 2.5 - 5.0 4.0 - 8.0 1.0 - 5.0EPX 045 – 1.5 - 3.0 – – 4.0 - 8.0 6.0 - 10.0 3.0 - 8.0 033 – 2.0 - 4.0 – 1.5 - 3.0 5.0 - 10.0 8.0 - 13.0 5.0 - 10.0 026 – 2.5 - 6.0 1.0 - 3.0 2.0 - 4.0 8.0 - 13.0 8.0 - 13.0 –

013 – 5.0 - 10.0 1.0 - 5.5 4.0 - 8.0 – – –007 3 8.0 - 13.0 3.0 - 8.0 7.0 - 13.0 – – –

005 5 14 - 19 4.0 - 10.0 8.0 - 15.0 – – –

LBB36/37 H060 – 1.0 - 2.0 – – 2.5 - 5.0 4.0 - 8.0 1.0 - 5.0 H033 – 2.0 - 4.0 – 1.5 - 3.0 5.0 - 10.0 8.0 - 13.0 5.0 - 10.0 H026 – 2.5 - 6.0 1.0 - 3.0 2.0 - 4.0 8.0 - 13.0 8.0 - 13.0 8.0 - 13.0 H013 – 5.0 - 10.0 1.0 - 5.5 4.0 - 8.0 – – – H007 3 8.0 - 13.0 3.0 - 8.0 7.0 - 13.0 – – – H005 5 14.0 - 19.0 – – – – –

LBB45 H017 – – – – 10.0 - 16.0 16.0 - 50.0 10.0 - 16.0 H006 – 10.0 - 16.0 4.0 - 10.0 8.0 - 16.0 16.0 - 23.0 – 16.0 - 23.0 H004 – 16.0 - 23.0 6.0 - 16.0 13.0 - 23.0 – – –

D r i l l d i m e n s i o n / m m


32/113

31

For the most confined spaces. The LBV-series ofangle drills are available in four basic versions.• 30º angle (-30)• 45º angle (-45)• 90º angle (-90)• 360º angle (-90Z)

Angle drill LBV 11/16/34/36

The straight drills are used mainly for verticaldrilling applications and drilling in crampedand awkward places.

Straight drill LBB 24/34

Air Sound Chuck consumption Air level Free capa- Weight at free speed Hose size inlet at free

speed city thread speed With chuck Without chuckModel r/min mm kg lb l/s cfm mm in BSP dB(A) Ordering No. Model Ordering No.

Drills with rear exhaust

LBB24 S200B 19000 6.5 0.8 1.7 6.0 13.0 6.3 1/4 1/4 75 8421 0205 15 -S200U 8421 0205 56LBB24 S060B 6000 6.5 0.8 1.7 6.0 13.0 6.3 1/4 1/4 75 8421 0205 17 -S060U 8421 0205 19LBB24 S045B 4500 6.5 0.8 1.7 6.0 13.0 6.3 1/4 1/4 75 8421 0205 23 -S045U 8421 0205 64LBB24 S033B 3300 6.5 0.8 1.7 6.0 13.0 6.3 1/4 1/4 75 8421 0205 31 -S033U 8421 0205 72LBB24 S020B 2000 6.5 0.8 1.7 6.0 13.0 6.3 1/4 1/4 75 8421 0205 49 -S020U 8421 0205 80Drills with side exhaust

LBB34 S060 6000 10.0 1.1 2.4 10.0 21.0 10.0 3/8 1/4 88 8421 0309 41 -S060U 8421 0309 74LBB34 S026 2600 10.0 1.1 2.4 10.0 21.0 10.0 3/8 1/4 88 8421 0309 25 -S026U 8421 0309 82LBB34 S013 1300 10.0 1.5 3.3 10.0 21.0 10.0 3/8 1/4 87 8421 0309 17 -S013U 8421 0309 90

ACCESSORIES INCLUDEDChuck, chuck key, hose nipple.Suspension yoke and chuck guard.Push button set.Exhaust hose (-24 models).

Continued...

Sound Collet or level Setting chuck Air consumption Hose Air inlet at free With

Free speed range capacity Weight at free speed dimension thread speed spindle lockModel r/min rpm mm kg lb l/s cfm mm in BSP dB(A) Ordering No. Ordering No.

30o angle head

LBV11 S027-S30 2700 – 5.0 0.5 1.1 3.2 6.8 5.0 1/8 1/4 73 8421 0108 70 –LBV16 032-S30 3200 1500-3200 5.0 0.45 1.0 8.7 18.4 6.3 1/4 1/4 74 8421 0110 04 8421 0110 29LBV16 032-30 3200 1500-3200 5.0 0.5 1.1 8.7 18.4 6.3 1/4 1/4 74 8421 0110 05 8421 0110 30LBV16 032-S32 3200 1500-3200 c 0.45 1.0 8.7 18.4 6.3 1/4 1/4 74 8421 0110 06 8421 0110 31LBV16 032-32 3200 1500-3200 c 0.5 1.1 8.7 18.4 6.3 1/4 1/4 74 8421 0110 07 8421 0110 32LBV16 045-32 4500 3200-4500 5.0 0.5 1.1 8.7 18.4 6.3 1/4 1/4 74 – 8421 0110 57LBV36 S030-30d 3000 – 5.0 1.0 2.2 17.0 36.0 10.0 3/8 1/4 82 8421 0414 70 –LBV36 S030-S30d 3000 – 5.0 0.9 2.0 17.0 36.0 10.0 3/8 1/4 82 8421 0414 71 –LBV36 S045-30d 4500 – 5.0 1.0 2.2 17.0 36.0 10.0 3/8 1/4 82 8421 0414 72 –45o angle head

LBV16 032-45 3200 1500-3200 5.0 0.5 1.1 8.7 18.4 6.3 1/4 1/4 74 8421 0110 59 –LBV16 032-46 3200 1500-3200 c 0.5 1.1 8.7 18.4 6.3 1/4 1/4 74 8421 0110 60 –90o angle head

LBV11 S025-S90 2500 – 5.0 0.5 1.1 3.2 6.8 5.0 1/8 1/4 73 8421 0109 79 –LBV16 032-90 3200 1500-3200 5.0 0.5 1.1 8.7 18.4 6.3 1/4 1/4 74 8421 0110 00 8421 0110 25LBV16 032-S90 3200 1500-3200 5.0 0.45 1.0 8.7 18.4 6.3 1/4 1/4 74 8421 0110 01 8421 0110 26LBV16 032-S92 3200 1500-3200 c 0.45 1.0 8.7 18.4 6.3 1/4 1/4 74 8421 0110 02 8421 0110 27LBV16 032-92 3200 1500-3200 c 0.5 1.1 8.7 18.4 6.3 1/4 1/4 74 8421 0110 03 8421 0110 28LBV16 045-90 4500 3200-4500 5.0 0.5 1.1 8.7 18.4 6.3 1/4 1/4 74 8421 0110 20 8421 0110 44LBV16 045-92 4500 3200-4500 c 0.5 1.1 8.7 18.4 6.3 1/4 1/4 74 8421 0110 21 8421 0110 45LBV16 055-90 5500 4500-5500 5.0 0.5 1.1 8.7 18.4 6.3 1/4 1/4 74 8421 0110 23 8421 0110 46LBV16 055-92 5500 4500-5500 c 0.5 1.1 8.7 18.4 6.3 1/4 1/4 74 8421 0110 24 8421 0110 47LBV16 055-S92 5500 4500-5500 c 0.45 1.0 8.7 18.4 6.3 1/4 1/4 74 8421 0110 58 –LBV36 S030-90d 3000 – 5.0 1.0 2.2 17.0 36.0 10.0 3/8 1/4 82 8421 0414 60 –LBV36 S030-S90d 3000 – 5.0 0.9 2.0 17.0 36.0 10.0 3/8 1/4 82 8421 0414 61 –LBV36 S045-90d 4500 – 5.0 1.0 2.2 17.0 36.0 10.0 3/8 1/4 82 8421 0414 62 –LBV36 S045-S90d 4500 – 5.0 0.9 2.0 17.0 36.0 10.0 3/8 1/4 82 8421 0414 63 –LBV36 S030-92d 3000 – c 1.0 2.2 17.0 36.0 10.0 3/8 1/4 82 8421 0414 64 –LBV36 S030-S92d 3000 – c 0.9 2.0 17.0 36.0 10.0 3/8 1/4 82 8421 0414 65 –LBV36 S045-92d 4500 – c 1.0 2.2 17.0 36.0 10.0 3/8 1/4 82 8421 0414 66 –

360o angle headLBV16 032-90Z 3200 1500-3200 5.0 0.5 1.1 8.7 18.4 6.3 1/4 1/4 74 8421 0110 64 8421 0110 65LBV16 032-92Z 3200 1500-3200 c 0.5 1.1 8.7 18.4 6.3 1/4 1/4 74 8421 0110 68 8421 0110 69

24- and 34-models have a 3/8" -24 UNF spindle thread.

LBB 24 210 WLBB 35 400 W

M


M a t e r i a


LBV 11 110 W

LBV 16 300 W

LBV 34 400 W

LBV 36 510 W


33/113

32

Service kits


For LBB. Quick chuck

Mount Chuck capacity Ordering No.

3/8-24UNF 0.0–6.5 4021 0400 003/8-24UNF 0.0–8.0 4021 0401 003/8-24UNF 0.0–10.0 4021 0402 003/8-24UNF 2.0–13.0 4021 0403 00

Spot suction attachment

Model Hoze size Ordering No.

LBB16 1 1/4" 4110 1715 80LBB36/37 1 1/4" 4110 1716 80LBB26 4110 1715 84

For LBB24. Collet chuck and collets

Designation Capacity Ordering No.

mm Inch

Collet holder 3/8"-24 4110 0844 90Collet nut 4110 0760 00Collet 3 4150 0081 00 5 4150 0075 01 6 4150 0075 00 8 5/16 4150 0074 00 1/8 4150 0082 00

5/32 4150 0648 00 3/16 4150 0649 00 1/4 4150 0076 00


Collet or chuck with keyPush button setHose nipple3 mm collet (5.0 collet capacity head)

6 mm collet (6.6 collet capacity head)

Sound Collet or level Setting chuck Air consumption Hose Air inlet at free With Free speed range capacity Weight at free speed dimension thread speed spindle lock

Model r/min rpm mm kg lb l/s cfm mm in BSP dB(A) Ordering No. Ordering No.

90o angle head – large angle head

LBV16 045-91 4500 3200-4500 6.6 0.55 1.2 8.7 18.4 6.3 1/4 1/4 74 8421 0110 38 –LBV16 032-91 3200 1500-3200 6.6 0.55 1.2 8.7 18.4 6.3 1/4 1/4 74 8421 0110 09 8421 0110 34LBV16 032-93 3200 1500-3200 c 0.55 1.2 8.7 18.4 6.3 1/4 1/4 74 8421 0110 10 8421 0110 35LBV16 032-S93 3200 1500-3200 c 0.45 1.2 8.7 18.4 6.3 1/4 1/4 74 8421 0110 39 –

LBV16 010-91 1000 500-1000 6.6 0.6 1.2 8.7 18.4 6.3 1/4 1/4 74 8421 0110 16 8421 0110 40LBV16 010-93 1000 500-1000 c 0.6 1.2 8.7 18.4 6.3 1/4 1/4 74 8421 0110 17 8421 0110 41LBV16 018-91 1800 800-1800 6.6 0.55 1.2 8.7 18.4 6.3 1/4 1/4 74 8421 0110 18 8421 0110 42LBV16 018-93 1800 800-1800 c 0.55 1.2 8.7 18.4 6.3 1/4 1/4 74 8421 0110 19 8421 0110 43LBV16 005-91 500 200-500 6.6 0.6 1.2 8.7 18.4 6.3 1/4 1/4 74 8421 0110 11 8421 0110 36LBV16 005-93 500 200-500 c 0.6 1.2 8.7 18.4 6.3 1/4 1/4 74 8421 0110 12 8421 0110 37LBV36 S030-91d 3000 – 6.6 1.0 2.2 17.0 36.0 10.0 3/8 1/4 82 8421 0414 50 –LBV36 S060-91d 6000 – 6.6 1.0 2.2 17.0 36.0 10.0 3/8 1/4 82 8421 0414 51 –LBV36 S030-93d 3000 – c 1.0 2.2 17.0 36.0 10.0 3/8 1/4 82 8421 0414 52 –LBV36 S060-93d 6000 – c 1.0 2.2 17.0 36.0 10.0 3/8 1/4 82 8421 0414 53 –90o angle head – key chuck models

LBV16 018-11 1800 800-1800 6.5a 0.8 1.7 8.7 18.4 6.3 1/4 1/4 74 8421 0110 22 –LBV34 S040b 4000 – 6.5a 1.5 3.3 7.5 15.9 10.0 3/8 1/4 88 8421 0309 46 –LBV34 S010b 1000 – 10.0a 2.0 4.4 7.5 15.9 10.0 3/8 1/4 88 8421 0309 12 –LBV34 S005b 500 – 13.0a 2.1 4.6 7.5 15.9 10.0 3/8 1/4 87 8421 0309 04 –

a) Spindle thread, male 3/8"-24 UNF.b)

Side exhaust.c) Internal thread 1/4"-28.d) Short lever as standard.

For LBV11/16/36/37. Collets with max 5.0 capacity

Capacity Ordering No. Capacity Ordering No.

mm mm

1.0 4110 0438 01 3.7 4110 0438 34

1.5 4110 0438 02 3.8 4110 0438 14

1.8 4110 0438 28 3.9 4110 0438 35

2.0 4110 0438 03 4.0 4110 0438 15

2.1 4110 0438 29 4.1 4110 0438 25

2.2 4110 0438 04 4.2 4110 0438 26

2.3 4110 0438 30 4.3 4110 0438 36

2.4 4110 0438 05 4.4 4110 0438 37

2.5 4110 0438 06 4.5 4110 0438 16

2.2 4110 0438 07 4.6 4110 0438 38

2.7 4110 0438 31 4.7 4110 0438 39

2.8 4110 0438 32 4.8 4110 0438 18

2.9 4110 0438 08 4.9 4110 0438 40

3.0 4110 0438 09 5.0 4110 0438 27

3.1 4110 0438 10 1/16 4110 0438 19

3.2 4110 0438 11 3/32 4110 0438 20

3.3 4110 0438 12 1/8 4110 0438 21

3.4 4110 0438 33 5/32 4110 0438 22

3.5 4110 0438 13 3/16 4110 0438 23

3.6 4110 0438 24

Power feed arm for LBB36 H005 and LBB37 H006

Ordering No.

Adapter piece (SR295), 410 1416 80

lever arm (SR201),

chain (SR202) and

MK 2 adapter (SR206)

Two extension pieces 4110 1417 80

(SR204-1 and SR204-2)370 and 750 mm long.

MK 2 adapter 4110 1416 01

Model Ordering No.

LBB16 4081 0271 90

LBB/LBV24 4081 0005 90

LBB26 4081 2028 90

LBB/LBV34 4081 0035 90

LBB36/37 4081 0194 90

LBB45 4081 0139 90

LBV16 4081 0322 90

LBV36 (30, 90/92) 4081 0263 90

LBV36 (91/93) 4081 0251 90


34/113

33

Drilling and tapping

Applications Pistol grip drills Atlas Copco large pistol grip drills aresuitable for most drilling tasks in virtuallyevery sector of industry.

LBB 45 is a two-hand pistol grip drill forlarger bit diameters. LBB 45 keeps constantspeed at varying feed forces thanks to thespeed governor. The feed force can befurther increased with the aid of a breast plate or feed screw, which are available asoptional accessories.

Screw feed drills Atlas Copco screw-feed drills RAB are idealfor heavy duty drilling operations requiringhigh feed forces. You can also use thesedrills for reaming, tapping and tuberolling.• Simple and reliable design.• The speed governor keeps the

drilling speed constant and reducesair consumption as power is reduced.

• Safer – thanks to the safety catchwhich prevents accidental starting.

The throttle is also self closing.

Tappers Atlas Copco tappers LGB are designed fortapping and thread cleaning with thread taps.As standard the tools are fitted with a tapchuck.• Comfortable and effective. The ergonomic

design of the handle gives you a com-fortable grip and maximum performance.

• Higher productivity thanks to the doublespeed when you withdraw the machine.

• Low noise level. The rearward-directedexhaust gives a lower noise level.

M


M a t e r i a



35/113

34

Pistol grip drill LBB 45

ChuckAir consumption

Air Sound level Free capa-

Weight at free speed Hose size inlet at free

speed city thread speed With chuckModel r/min mm kg lb l/s cfm mm in BSP dB(A) Ordering No.

Non-reversible drills with air supply through handle

LBB45 H017a 1700 16.0 4.2 9.3 10.0 21.0 10.0 3/8 1/4 85b 8421 0501 32LBB45 H006a 600 16.0 4.3 9.3 10.0 21.0 10.0 3/8 1/4 85b 8421 0501 24LBB45 H004a 400 16.0 4.3 9.3 10.0 21.0 10.0 3/8 1/4 85b 8421 0501 16

Free speed

Hose Air

Air con-

TappingWeight dimension

inletsumption

With chuck Without chuck

Forward Reverse capacity threadModel r/min r/min mm kg lb mm in BSP l/s cfm Ordering No. Model Ordering No.

Pistol grip tappers with air supply through handle

LGB24 H007 700 1400 6 1.1 2.4 6.3 1/4 1/4 5.5 11.5 8421 0210 67 -U 8421 0210 69LGB24 H007Qa 700 1400 6 1.1 2.4 6.3 1/4 1/4 5.5 11.5 8421 0210 75 – –LGB34 H007 700 1400 10 1.8 4.0 10.0 3/8 1/4 7.5 15.9 8421 0311 66 -U 8421 0311 68LGB34 H007Qa 700 1400 10 1.8 4.0 10.0 3/8 1/4 7.5 15.9 8421 0311 76 – –LGB36 H007Qa 700 1400 12 2.0 4.4 10.0 3/8 3/8 16.5 34.9 8421 0411 00 – –Pistol grip tappers with air supply on top

LGB24 HF007Qa 700 1400 10 1.2 2.6 6.3 1/4 1/4 6.0 12.7 8421 0210 82 – –Straight tappers

LGB24 S007 700 1400 6 1.1 2.4 6.3 1/4 1/4 5.5 11.6 8421 0210 71 -U 8421 0210 73LGB34 S007 700 1400 10 1.8 4.0 10.0 3/8 1/4 7.5 15.9 8421 0311 72 -U 8421 0311 74

a) Quick change system.Taper: Jacob 1.


Chuck, chuck key, hose nipple.JT3 taper mount.

a) Including support handle.

b) 79 dB(A) with silencer set 4112 0863 80.

Chuck Air consumption Air Sound level Free capa- Weight at free speed Hose size inlet at free

speed city thread speed With chuckModel r/min mm kg lb l/s cfm mm in BSP dB(A) Ordering No.

Reversible drills

Industrial Tools and Solutions.pdf

Documents

Transcript of Industrial Tools and Solutions.pdf