Included Installation Instructions Network ... - Panasonic

Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.

The model number is abbreviated in some descriptions in this manual.This document is the Installation Guide for use in other countries except Japan.

Installation GuideIncluded Installation Instructions

Network Camera

Model No.

(This illustration represents WV-SPW611.)

WV-SPW631LTWV-SPW631LWV-SPW611LWV-SPW611

2

WARNING:• To prevent injury, this apparatus must be

securely attached to the floor/wall/ceiling in accordance with the installation instructions.

• The installation shall be carried out in accor-dance with all applicable installation rules.

• The connections should comply with local electrical code.

The model number and serial number of this product may be found on the surface of the unit.You should note the model number and serial number of this unit in the space provided and retain this book as a permanent record of your purchase to aid identification in the event of theft.

Model No. Serial No.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digi-tal device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environ-ment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction man-ual, may cause harmful interference to radio com-munications.Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the inter-ference at his own expense.

FCC Caution: To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

For U.S.A

For U.S.A

CAN ICES-3(A)/NMB-3(A)For Canada

We declare under our sole responsibility that the product to which this declaration relates is in conformity with the standard or other normative document following the provisions of Directive 2004/108/EC.

Wir erklären in alleiniger Verantwortung, daß das Produkt, auf das sich diese Erklärung bezieht, mit der folgenden Norm oder normativen Dokument übereinstimmt. Gemäß den Bestimmungen der Richtlinie 2004/108/EC.

Nous déclarons sous notre propre responsabilité que le produit auquel se réfère la présente déclaration est conforme á la norme spécifiée ou à tout autre document normatif conformément aux dispositions de la directive 2004/108/CE.

Nosotros declaramos bajo nuestra única responsabilidad que el producto a que hace referencia esta declaración está conforme con la norma u otro documento normativo siguiendo las estipulaciones de la directiva 2004/108/CE.

Noi dichiariamo sotto nostra esclusiva responsabilità che il prodotto a cui si riferisce la presente dichiarazione risulta conforme al seguente standard o altro documento normativo conforme alle disposizioni della direttiva 2004/108/CE.

Wij verklaren als enige aansprakelijke, dat het product waarop deze verklaring betrekking heeft, voldoet aan de volgende norm of ander normatief dokument, overeenkomstig de bepalingen van Richtlijn 2004/108/EC.

Vi erklærer os eneansvarlige for, at dette produkt, som denne deklaration omhandler, er i overensstemmelse med standard eller andre normative dokumenter i følge bestemmelserne i direktiv 2004/108/EC.

Vi deklarerar härmed vårt fulla ansvar för att den produkt till vilken denna deklaration hänvisar är i överensstämmelse med standarddokument eller annat normativt dokument som framställs i direktiv 2004/108/EC.

Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämä ilmoitus koskee, noudattaa seuraavaa standardia tai muuta ohjeellista asiakirjaa, jotka noudattavat direktiivin 2004/108/EC säädöksiä.

Vi erklærer oss alene ansvarlige for at produktet som denne erklæringen gjelder for, er i overensstemmelse med følgende norm eller andre normgivende dokumenter som følger bestemmelsene i direktiv 2004/108/EC.

For Europe

3

Contents

Important safety instructions ......................................................................................................... 4Limitation of liability ....................................................................................................................... 5Disclaimer of warranty ................................................................................................................... 5Preface .......................................................................................................................................... 5About notations ............................................................................................................................. 6Main functions ............................................................................................................................... 6About the user manuals ................................................................................................................ 7System requirements for a PC ...................................................................................................... 7Trademarks and registered trademarks......................................................................................... 8Copyright ....................................................................................................................................... 8Network security ........................................................................................................................... 9Precautions ................................................................................................................................. 10Precautions for installation .......................................................................................................... 14Major operating controls ............................................................................................................. 16Preparations ................................................................................................................................ 19Installations/Connections ............................................................................................................ 20Insert/remove an SD memory card* ............................................................................................ 29Adjustment .................................................................................................................................. 30Mounting the front cover ............................................................................................................. 33Attaching the mounting surface on the top surface of the camera body.................................... 34Configure the network settings ................................................................................................... 37Troubleshooting ........................................................................................................................... 39Specifications .............................................................................................................................. 41Standard accessories .................................................................................................................. 48Optional accessories ................................................................................................................... 48

* SDXC/SDHC/SD memory card is described as SD memory card.

4

Important safety instructions

1) Readtheseinstructions.

2) Keeptheseinstructions.

3) Heedallwarnings.

4) Followallinstructions.

5) Donotblockanyventilationopenings. Install inaccordancewith themanufacturer's instruc-tions.

6) Donotinstallnearanyheatsourcessuchasradiators,heatregisters,stoves,orotherappara-tus(includingamplifiers)thatproduceheat.

7) Onlyuseattachments/accessoriesspecifiedbythemanufacturer.

8) Useonlywith thecart,stand, tripod,bracket,or tablespecifiedby themanufacturer,orsoldwiththeapparatus.Whenacartisused,usecautionwhenmovingthecart/apparatuscombi-nationtoavoidinjuryfromtip-over.

S3125A

9) Unplugthisapparatusduringlightningstormsorwhenunusedforlongperiodsoftime.

10) Referallservicingtoqualifiedservicepersonnel.Servicingisrequiredwhentheapparatushasbeendamaged inanyway,suchaspower-supplycordorplug isdamaged, liquidhasbeenspilledorobjectshave fallen into theapparatus, theapparatushasbeenexposed to rainormoisture,doesnotoperatenormally,orhasbeendropped.

5

Limitation of liabilityTHIS PUBLICATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHEREXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OFMERCHANTABILITY,FITNESSFORANYPARTICULARPURPOSE,ORNON-INFRINGEMENTOFTHETHIRDPARTY'SRIGHT.THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICALERRORS. CHANGES ARE ADDED TO THE INFORMATION HEREIN, AT ANY TIME, FOR THEIMPROVEMENTSOFTHISPUBLICATIONAND/ORTHECORRESPONDINGPRODUCT(S).

Disclaimer of warranty

INNOEVENTSHALLPanasonicSystemNetworksCo.,Ltd.BELIABLETOANYPARTYORANYPERSON,EXCEPTFORREPLACEMENTORREASONABLEMAINTENANCEOFTHEPRODUCT,FORTHECASES,INCLUDINGBUTNOTLIMITEDTOBELOW:(1) ANY LOSS OR DAMAGE, INCLUDING WITHOUT LIMITATION, DIRECT OR INDIRECT,

SPECIAL, CONSEQUENTIAL OR EXEMPLARY, ARISING OUT OF OR RELATING TO THEPRODUCT;

(2) ANY INCONVENIENCE, LOSS, OR DAMAGE CAUSED BY INAPPROPRIATE USE ORNEGLIGENTOPERATIONOFTHEUSER;

(3) ALLMALFUNCTIONSORTROUBLESFROMUNAUTHORIZEDDISASSEMBLE,REPAIRORMODIFICATIONOFTHEPRODUCTBYTHEUSER,REGARDLESSOFTHECAUSEOFTHEMALFUNCTIONORTROUBLE;

(4) INCONVENIENCEORANYLOSSARISINGWHEN IMAGESARENOTDISPLAYED,DUETOANYREASONORCAUSEINCLUDINGANYFAILUREORPROBLEMOFTHEPRODUCT;

(5) ANY PROBLEM, CONSEQUENTIAL INCONVENIENCE, OR LOSS OR DAMAGE, ARISINGOUTOFTHESYSTEMCOMBINEDBYTHEDEVICESOFTHIRDPARTY;

(6) ANYCLAIMORACTIONFORDAMAGES,BROUGHTBYANYPERSONORORGANIZATIONBEINGAPHOTOGENICSUBJECT,DUETOVIOLATIONOFPRIVACYWITHTHERESULTOFTHAT SURVEILLANCE-CAMERA'S PICTURE, INCLUDING SAVED DATA, FOR SOMEREASON,BECOMESPUBLICORISUSEDFORANYPURPOSE;

(7) LOSSOFREGISTEREDDATACAUSEDBYANYFAILURE.

Thenetworkcamera isdesigned tooperateusingaPConanetwork (10BASE-T/100BASE-TX),andcanbeinstalledoutdoors.Byconnectingtoanetwork(LAN)ortheInternet,imagesandaudiofromthecameracanbemoni-toredonaPCviaanetwork.

Note: • It is necessary to configure the network settings of the PC and its network environment to

monitorimagesfromthecameraonthePC.ItisalsonecessarytoinstallawebbrowseronthePC.

Preface

6

Equipped with a new codec engineTheredesignedcodecenginecanoutputupto60framespersecondinFull-HD( SPW631LT SPW631L )quality.

The equipped enhanced Super Dynamic function makes it possible to achieve 133 dB dynamic range.Bycombiningimagestakenatdifferentshutterspeedsandusingpixellevelbrightnesscorrection,morenaturallookingpicturescanbetakenevenwhenobjectshavelargedifferencesinillumination.*Whenframerateissetto60fps,OffisdisplayedforSuperDynamicfunction.

Equipped with a high-sensitivity MOS sensor and noise reduction function (MNR)Thehigh-sensitivitysensorandnewmethodofnoisereduction(MNR:Multi-processNoiseReduction)*1makeitpossibletotakeeasy-to-viewimagesevenunderlowilluminationconditions.*1Withthemulti-processnoisereductionthatprioritizesnoisereductionforcentralareasandreso-lutionforedgeareaswherenoiseisprominent,MNRisabletoproduceclearimageswhilelimit-ingnoiseacrosstheentireimage.

IR LED equipped SPW631LT SPW631L SPW611L

TheequippedinfraredLEDmakesitpossibletotakepicturesatzerolxofobjectsasfaras30m{98.43feet}away.

Equipped with 2 SD memory card slots and enhanced image recording • Byusing2SDmemorycardssequentially,imagescanberecordedoverlongperiodsoftime. • Thedualrecordingfunction(recordingimageson2SDmemorycardssimultaneously)makesit

possibletobackupdata.

Extension Software supportInstallingExtensionSoftware*2makesitpossibletoaddfunctionsthatuseimagedata.*2ForfurtherinformationaboutExtensionSoftwarerefertoourwebsite(http://security.panasonic.com/pss/security/support/info.html).

About notationsThefollowingnotationsareusedwhendescribingthefunctionslimitedforspecifiedmodels.Thefunctionswithoutthenotationsaresupportedbyallmodels.SPW631LT :ThefunctionswiththisnotationareavailablewhenusingthemodelWV-SPW631LT.SPW631L :ThefunctionswiththisnotationareavailablewhenusingthemodelWV-SPW631L.SPW611L :ThefunctionswiththisnotationareavailablewhenusingthemodelWV-SPW611L.SPW611 :ThefunctionswiththisnotationareavailablewhenusingthemodelWV-SPW611.

Main functions

7

About the user manuals

There are2 sets of operating instructions for theWV-SPW631LT,WV-SPW631L,WV-SPW611L,WV-SPW611asfollows. • InstallationGuide:Explainshowtoinstallandconnectdevices. • Operating Instructions (included in theCD-ROM): Explains how to perform the settings and

howtooperatethiscamera.

Adobe®Reader®isrequiredtoreadtheseoperatinginstructionsontheprovidedCD-ROM.WhentheAdobeReader isnot installedon thePC,downloadthe latestAdobeReader fromtheAdobewebsiteandinstallit.

Englishscreensareusedintheseoperatinginstructions.

System requirements for a PC

CPU: Intel®CoreTM2Duo2.4GHzorfasterrecommendedMemory: Aminimumof1GBormore (for32-bitOSs),2GBormore (for64-bitOSs)

memory is requiredwhen usingMicrosoft®Windows® 8.1,Microsoft®Windows®8,Microsoft®Windows®7.

Aminimumof 1GBormorememory is requiredwhen usingMicrosoft®WindowsVista®.

Networkinterface: 10BASE-T/100BASE-TX1portAudiointerface: Soundcard(whenusingtheaudiofunction)Monitor: Imagecapturesize:1024x768pixelsormore Color:24-bitTruecolororbetterOS: Microsoft®Windows®8.1 Microsoft®Windows®8 Microsoft®Windows®7 Microsoft®WindowsVista®

Webbrowser: Windows®InternetExplorer®11(32-bit) Windows®InternetExplorer®10(32-bit) Windows®InternetExplorer®9(32-bit) Windows®InternetExplorer®8(32-bit) Windows®InternetExplorer®7(32-bit)

The camera conforms to the IP66*3 and Type 4X (UL50), is compliant with NEMA 4X*4 ratings, and provides high dust resistance and waterproof performance.Waterproofing treatment isnot required for thecamerabody (waterproofing treatment is requiredforcableconnections).*3IP66rating:Theapplicableproducthas"Dusttight(6)"protectionagainstforeignsolidsandhas"Powerfulwaterjets(6)"againstwater(IEC60529).

*4NEMA:DustresistanceandwaterproofperformancestandardssetbyNationalElectricalManufacturersAssociation(UnitedStates).

8

Others: CD-ROMdrive (Itisnecessarytoreadtheoperatinginstructionsandusethesoftwareon

theprovidedCD-ROM.) Adobe®Reader®

(ItisnecessarytoviewthePDFfileontheprovidedCD-ROM.)

IMPORTANT: • When using a PC that does not meet the above requirements, displaying of images may

becomeslowerorthewebbrowsermaybecomeinoperable. • Audiomaynotbeheard if a soundcard isnot installedonaPC.Audiomaybe interrupted

dependingonthenetworkenvironment. • MicrosoftWindowsRT,MicrosoftWindows7StarterandMicrosoftWindowsVistaStarterare

notsupported. • WhenusingWindows8.1orWindows8,useitinthedesktop.Thesoftwarecannotbeusedin

theModernUIdesign.

Note: • For further informationaboutPCsystemrequirementsandprecautions forwhenusingMicrosoft

Windows8.1,MicrosoftWindows8,MicrosoftWindows7,MicrosoftWindowsVista,orWindowsInternet Explorer, click "Manual" - "Open" from the supplied CD-ROM and refer to "Notes onWindows®/InternetExplorer®versions".

• Forinformationontheoperationverificationofthesupportedoperatingsystemsandwebbrows-ers,refertoourwebsiteathttp://security.panasonic.com/pss/security/support/index.html.

Trademarks and registered trademarks

• Adobe,theAdobelogo,andReaderareeitherregisteredtrademarksortrademarksofAdobeSystemsIncorporatedintheUnitedStatesand/orothercountries.

• Microsoft,Windows,WindowsVista, Internet Explorer, ActiveX, andDirectX are either regis-tered trademarks or trademarks of Microsoft Corporation in the United States and/or othercountries.

• Microsoftproductscreenshot(s)reprintedwithpermissionfromMicrosoftCorporation. • IntelandIntelCorearetrademarksorregisteredtrademarksofIntelCorporationoritssubsid-

iariesintheUnitedStatesandothercountries. • SDXCLogoisatrademarkofSD-3C,LLC. • iPad, iPhone,and iPod touchare trademarksofApple Inc., registered in theU.S.andother

countries. • AndroidisatrademarkofGoogleInc.UseofthistrademarkissubjecttoGooglePermissions. • Allothertrademarksidentifiedhereinarethepropertyoftheirrespectiveowners.

Copyright

Distributing, copying, disassembling, reverse compiling and reverse engineering of the softwareprovidedwiththisproductareallexpresslyprohibited.Inaddition,exportinganysoftwareprovidedwiththisproductviolatingexportlawsisprohibited.

9

Network security

Asyouwillusethisunitconnectedtoanetwork,yourattention iscalledtothe followingsecurityrisks.q Leakageortheftofinformationthroughthisunitw Useofthisunitforillegaloperationsbypersonswithmaliciousintente InterferencewithorstoppageofthisunitbypersonswithmaliciousintentIt is your responsibility to take precautions such as those described below to protect yourselfagainsttheabovenetworksecurityrisks. • Usethisunitinanetworksecuredbyafirewall,etc. • If this unit is connected to a network that includes PCs,make sure that the system is not

infectedby computer viruses or othermalicious entities (using a regularly updated anti-virusprogram,anti-spywareprogram,etc.).

• Protectyournetworkagainstunauthorizedaccessbyrestrictinguserstothosewhologinwithanauthorizedusernameandpassword.

• Applymeasuressuchasuserauthenticationtoprotectyournetworkagainstleakageortheftofinformation, including image data, authentication information (user names and passwords),alarmmailinformation,FTPserverinformationandDDNSserverinformation.

• Aftertheunitisaccessedbytheadministrator,makesuretoclosethebrowser. • Changetheadministratorpasswordperiodically. • Donot install the camera in locationswhere the cameraor the cables canbedestroyedor

damagedbypersonswithmaliciousintent.

10

Precautions

Refer installation work to the dealer.Installationwork requires techniqueandexperi-ences. Failure to observe this may cause fire,electricshock,injury,ordamagetothisproduct.Besuretoconsultthedealer.

Stop the operation immediately when something is wrong with this product. When smoke goes up from the product, thesmellofsmokecomesfromtheproduct,ortheexterior of the product has deteriorated, con-tinuedusewillcauseafireorfalloftheproductresulting in injury,accidents,ordamagetotheproduct.Turn the power off immediately and contactqualifiedservicepersonnelforservice.

Do not attempt to disassemble or modify this product. Failure toobserve thismaycause fireorelec-tricshock.Consultthedealerfortherepairorinspections.

Do not insert any foreign objects. Thiscouldpermanentlydamagethisproduct.Turn the power off immediately and contactqualifiedservicepersonnelforservice.

Select an installation area that can sup-port the total weight. Selecting an inappropriate installation surfacemaycause thisproduct to falldownor toppleover,resultingininjury.Installationworkshallbestartedaftersufficientreinforcement.

Periodic inspections shall be conducted. Rustonthemetalpartsorscrewsmaycauseafall of the product resulting in injury or acci-dents.Consultthedealerfortheinspections.

Do not use this product in an inflammable atmosphere.Failuretoobservethismaycauseanexplosionresultingininjury.

Avoid installing this bracket in the loca-tions where salt damage occurs or corro-sive gas is produced. Otherwise, themounting portionswill deterio-rateandaccidentssuchasafalloftheproductmayoccur.

Do not install this product in locations subject to vibration. Loosening of mounting screws or bolts maycauseafalloftheproductresultingininjury.

Install this product in a location high enough to avoid people and objects from bumping the product. Failure to observe this may cause a dropresultingininjuryoraccidents.

Do not strike or give a strong shock to this product.Failuretoobservethismaycausefireorinjury.

Turn the power off when do wiring of this product. Failure to observe this may cause electricshock.Inaddition,shortcircuitorwrongwiringmaycausefire.

The exclusively designed mount bracket shall be used.Failure to observe this may cause a dropresultingininjuryoraccidents.Usetheexclusivelydesignedmountbracketforinstallation.

The screws and bolts must be tightened to the specified torque.Failure to observe this may cause a dropresultingininjuryoraccidents.

Do not rub the edges of metal parts with your hand. Failuretoobservethismaycauseinjury.

11

Do not touch this product, the power cord or the connected cables during thunder. (even in the process of work)Failuretoobservethismaycauseelectricshock.

Keep SD memory card away from infants and children.Otherwise,theymayswallowthecardbymis-take.Inthiscase,consultadoctorimmediately.

The measures of protection against snow-fall shall be taken.In areaswhere lotsof snowaccumulates, theweightof snowmaycause theproduct to fallresulting in injury or accidents. Protect theproduct against snowfall by installing undereaves.

The screws and fixed parts must be securely tightened.Failure toobserve thismaycause theproducttofallresultingininjury.

The measures of protection against a fall of this product shall be taken. Failuretoobservethismaycauseadropresult-ingininjuryoraccidents.

Do not damage the power cable. Donotdamage,fabricate,twist,stretch,bun-dle,orforciblybendthepowercable.Donotplaceheavyobjects.Keepawayfromheatsources.Use of the damaged power cablemay causeelectricshock,shortcircuit,orfire.Consultthedealerforrepair.

Do not install this product on a place that is greatly influenced by wind.Installationonaplacewherethewindspeedis40m {131.23 feet} ormore per secondmaycauseafalloftheproductresultingininjuryoraccidents.

Turn the power off when cleaning this product. Failuretoobservethismaycauseinjury.

[Precautions for use]

This product has no power switch. When turning off the power, disconnect thepowersupplyfromthe12VDCpowersupplyorthePoEdevice. (Whenusingboththe12VDCpower supply and the PoE device for powersupply,disconnectboththeconnections.)

To keep on using with stable performanceDonotusethisproductinhotandhumidcon-ditions for a long time. Failure to observe thiscausescomponentdegradationresultinginlifeshorteningofthisproduct.Do not expose the product to direct heatsourcessuchasaheater.

Do not touch the front cover (transparent cover) with your bare hands.Adirtycovercausesdeteriorationofpicturequality.

Handle this product with care. Donot drop this product, nor apply shock orvibrationtotheproduct.Failuretoobservethismaycause trouble. Ifastrongshockorvibra-tion isappliedto the frontcover, itmaycausedamageorallowwatertoenterthisproduct.

About the batteryAbatteryisinstalledinsidethecamera.Donotleave the battery exposed in environments ofexcessiveheatasaresultofsunlightorfire.

About the PC monitorDisplaying thesame imageonamonitor foralongtimemaydamagethemonitor.Itisrecom-mendedtouseascreen-saver.

When an error is detected, this product will restart automatically.This product will be inoperable for around 2minutesaftertherestartjustaswhenthepoweristurnedon.

12

About the automatic status detection functionWhen this product malfunctions due to exoge-nous noise, etc. for 30 seconds or more, theproductwillautomaticallyresetandwillreturntonormalstate.Whentheproductisreset,initializa-tionwillbecarriedoutaswhenthepoweroftheproduct is turnedon.Whentheproductrepeat-edly resets, exogenous noise level around theproductmaybe high and thatmay causemal-function.Contactyourdealerforinstructions.

Product disposal/transferDatasavedonthisproductorastoragedeviceused with this product may lead to personalinformationleakage.When it is necessary to dispose or give thisproducttosomeone,evenwhenforrepair,makesurethatthereisnodataonthisproduct.

Cleaning this product bodyBesure to turnoff thepowerbeforecleaning.Failuretoobservethismaycauseinjury.Donotuse strong abrasive detergent when cleaningthisproduct.Otherwise,itmaycausediscolor-ation.When using a chemical cloth for clean-ing,readthecautionprovidedwiththechemi-calclothproduct.

Cleaning the lensUsealenscleaningpaper(usedtocleancam-eralensesorlensesofspectacles).Whenusingsolvent,useanalcoholssolventanddonotuseathinneroraglasscleaner.

Transmission intervalImage transmission intervalmaybecomeslowdepending on the network environment, PCperformance, shooting subject, access num-ber,etc.

Periodically images on the screen appear to be distortedWhenthecameraisinstalledinalocationwhereitissubjecttosmallvibrations(forexample,whenit is installed near devices that vibrate), imagesmayappeardistortedandstretchedlengthways.This phenomenon is a characteristic of imagepickup devices that use CMOS sensors and is

causedbytherelationshipbetweentheperiodicmovementsofthecameraandthetimingthattheimagesensor reads images.This isnotaprob-lemwiththecamera.Toreducethepossibilityofthisphenomenonoccurring,installthecamerainasecurelocation.

About SD memory card • To remove the SD memory card, hold

down theSDON/OFFbutton for about2seconds. When the flashing SD MOUNTlamp goes out, you can remove the SDmemorycard.

• WhenusinganSDmemorycard,formatitusing this product.Recordeddata on theSDmemorycardwillbedeletedwhenfor-matted.IfanunformattedSDmemorycardor an SD memory card formatted withother devices is used, this product maynotworkproperlyorperformancedeterio-ration may be caused. Refer to theOperating Instructions on the providedCD-ROMforhowtoformatanSDmemorycard.

• When some SD memory cards are usedwiththisproduct,theproductmaynotworkproperly or performance deterioration maybecaused.UsetheSDmemorycardsrec-ommendedinpage47.

• WhenusinganSDmemorycardsupportingClass 10 of the speed class, use aUHS-I(UltraHighSpeed-I)compliantcard.

Discoloration on the color filter of the MOS image sensor • When continuously shooting a bright light

sourcesuchasaspotlight, thecolor filteroftheMOSimagesensormayhavedeteri-orated and it may cause discoloration.Even when changing the fixed shootingdirection after continuously shooting aspotlight foracertainperiod, thediscolor-ationmayremain.

• Whenshootingfast-movingsubjectsorper-forming panning/tilting operations, objectscrossing theshootingareamay look tobebendingaskew.

13

Code labelThe code labels (accessory) are required atinquiry for trouble. Use caution not to losethese labels. It is recommended topaste oneofthelabelsontotheCD-ROMcase.

AVC Patent Portfolio LicenseTHISPRODUCTISLICENSEDUNDERTHEAVCPATENTPORTFOLIOLICENSEFORTHEPERSONALUSEOFACONSUMEROROTHERUSESINWHICHITDOESNOTRECEIVEREMUNERATIONTO(i)ENCODEVIDEOINCOMPLIANCEWITHTHEAVCSTANDARD("AVCVIDEO")AND/OR(ii)DECODEAVCVIDEOTHATWASENCODEDBYACONSUMERENGAGEDINAPERSONALACTIVITYAND/ORWASOBTAINEDFROMAVIDEOPROVIDERLICENSEDTOPROVIDEAVCVIDEO.NOLICENSEISGRANTEDORSHALLBEIMPLIEDFORANYOTHERUSE.ADDITIONALINFORMATIONMAYBEOBTAINEDFROMMPEGLA,L.L.C.SEEHTTP://WWW.MPEGLA.COM

About the dehumidifying device • This product has dehumidifying device to

keepthe insideat lowmoisture level,pre-ventingcondensationandquicklydissipat-ingdewifproduced.

• Dew may be produced depending on theconditions of temperature, humidity, winds,andrain,anditmaytaketimetodehumidify.

• Neversealthesurfacesofthedehumidify-ingdevice.

Dehumidifying device

14

Precautions for installation

Installing placeContact your dealer for assistance if you areunsureofanappropriateplaceinyourparticu-larenvironment. • Make sure that the installation area is

strong enough to hold this product, suchasaconcreteceiling.

• Installthecamerainthefoundationareaofthearchitectureorwheresufficientstrengthisassured.

• If a wall or ceiling board such as plasterboard is too weak to support the totalweight, the area shall be sufficiently rein-forced.

Do not place this product in the following places: • Locationswhereachemicalagent isused

suchasaswimmingpool • Locations subject to oil smoke such as a

kitchen • Locationsthathaveaspecificenvironment

that is subject to an inflammable atmo-sphereorsolvents

• Locations where a radiation, an X-ray, astrong radio wave or a strong magneticfieldisgenerated

• Locations where corrosive gas is pro-duced,locationswhereitmaybedamagedbybrinyairsuchasseashores

• Locations where the temperature is notwithinthespecifiedrange(☞ page41).

• Locationssubject tovibrations (Thisprod-uctisnotdesignedforon-vehicleuse.)

Be sure to remove this product if it is not in use.

Design and engineer the power supply system to turn on/off the power of this product. The product has no power switch. Wheninstalling the product, use a power supplydevice equipped with the ON-OFF switch forservicing.

About the network connectionWhenconnectingtoanetworkusingthenetworkcableofthisproduct,observethefollowing. • When wiring for the network, design and

engineernottobeaffectedbythunder. • It is impossible to install this product in

combinationwithapan/tilthead.

Screw tightening • The screws and bolts must be tightened

with an appropriate tightening torqueaccording to thematerial and strength oftheinstallationarea.

• Do not use an impact driver. Use of animpact drivermay damage the screws orcausetighteningexcessively.

• Tightenscrewsatarightangletothesur-face.Aftertighteningscrews,performvisu-al check to ensure tightening is so suffi-cientthatthereisnobacklash.

The measures of protection against a fall of this product shall be taken.Failuretoobservethismaycauseadropresultingininjuryoraccidents.Besuretoinstallthesafetywire.

Procure fixing screws separately. The screws that secure this product are notsupplied.Preparethemaccordingtothemate-rialandstrengthoftheareawheretheproductistobeinstalled.

Panasonic assumes no responsibility for injuries or property damage resulting from fail-ures arising out of improper installation or operation inconsistent with this documenta-tion.

15

Radio disturbanceWhenthisproductisusednearTV/radioanten-na,strongelectricfieldormagneticfield(nearamotor, a transformer or a power line), imagesmaybedistortedandnoisesoundmaybepro-duced.

Take notice of humidity.Install thisproductwhenthehumidity is low. Ifthis product is installed during rainfall or at ahigh humidity, the inside may be exposed tomoisture and the front cover may becomefoggy.

Heater unit Thisproduct isequippedwithan internalheaterunitforuseincoldclimates.Theheaterunitturnsonautomaticallywhenthetemperatureinsidetheproduct drops below0 °C {32 °F}.However, inanextremelylow-temperatureenvironmentbelow–30 °C {–22 °F}, snow and frost may not bedefrosted from the front cover.When using theproductincoldclimates,takenoticeoftheambi-entandinternaltemperaturesoftheproduct.Whenthisproduct is installedandoperated inlowtemperaturesbelow–10°C{14°F},normalimagesmaynotbeobtainedimmediatelyafterstartup.Insuchacase,waitaround2hoursormore,andturnonthepoweragain.

PoE (Power over Ethernet)Use a PoE hub/device that is compliant withIEEE802.3afstandard.

RouterWhenconnecting this product to the Internet,useabroadbandrouterwiththeport forward-ingfunction(NAT,IPmasquerade).RefertotheOperatingInstructions(includedintheCD-ROM)for further informationabouttheportforwardingfunction.

Time & date settingItisnecessarytosetthetime&datebeforeput-ting this product into operation. Refer to theOperatingInstructionsontheprovidedCD-ROMfordescriptionsofhowtoperformthesettings.

LAN cableShielded(STP*)LANcablesmustbeusedwiththisunittoensurecompliancewithEMCstan-dards.*ForEurope

16

Major operating controls

(This illustration represents WV-SPW611.)

Front cover

SunshieldRear part of sunshield

Rear cover

Safety wire

Tilting lock screw

Network cable

Alarm input/output cable

Power cable (12 V DC)

Microphone/line input cable (white)

Audio output cable (black)

Camera mount bracket (accessory)

RJ-45 (female)

EXT I/O terminal

Panning lock screw

17

(This illustration represents WV-SPW611.)Mount bracket cover x2 (accessories)

LINK indicator (lit when linking)Access indicator (lit when accessing)

Auto focus (AF) button

INITIAL SET button*

WIDE button

TELE button

SD memory card slot

SD slot 1 (SD1)

SD slot 2 (SD2)SD memory card error indicator/Auto focus indicator (blinks when adjusting auto focus)

*AboutINITIALSETbuttonFollowthestepsbelowtoinitializethenetworkcamera.qTurnoffthepowerofthecamera.WhenusingaPoEhub,disconnecttheLANcablefromthe

camera.Whenusinganexternalpowersupply,disconnectthepowercableplugfromthe12VDCpowersupplyterminal.

wTurnonthepowerofthecamerawhileholdingdowntheINITIALSETbutton,andthenkeepholdingdownthebuttonfor5secondsormore.About2minuteslater,thecamerawillstartupandthesettingsincludingthenetworksettingswillbeinitialized.

IMPORTANT: • When the camera is initialized, the settings including the network settingswill be initialized.

NotethattheCRTkey(SSLencryptionkey)usedfortheHTTPSprotocolwillnotbeinitialized. • Beforeinitializingthesettings,itisrecommendedtowritedownthesettingsinadvance. • Donotturnoffthepowerofthecameraduringtheprocessofinitialization.Otherwise,itmay

failtoinitializeandmaycausemalfunction.

18

<WV-SPW631L> <WV-SPW611>

IR LEDLens

Lens cover

SD-ON/OFF button

Packing PAL/NTSC switch

Monitor output jack

<WV-SPW631L><WV-SPW631LT>

Data Matrix: To our website*

*Dependingonthescanningapplicationused,theDataMatrixmaynotbeabletobereadcorrectly.Inthiscase,accessthesitebydirectlyenteringthefollowingURL.http://security.panasonic.com/pss/security/support/qr_sp_select.html

19

IMPORTANT: • Preparethemountingscrewsaccordingtothematerialof theareawherethecameramount

bracketandtheadapterboxaretobeinstalled.Inthiscase,woodscrewsandnailsshouldnotbeused.RecommendedtighteningtorqueM4:1.57N·m{1.16lbf·ft}

• Requiredpull-outcapacityofasinglescrew/boltis196N{44.06lbf}ormore. • Ifawallorceilingboardsuchasplasterboardistooweaktosupportthetotalweight,thearea

shallbesufficientlyreinforced.

• Thecameramountbracket(accessory)canbedirectlymountedonthewallusingajunctionbox(locallyprocured)embeddedinthewall,orawallwithacableaccesshole.

• Thescrewsthatsecurethecameramountbracketonawallarenotsupplied.Preparethescrewsaccordingtothematerial,structure,strengthandotherfactorsofthemountingareaandthetotalweightofobjectstobemounted.

Preparations

20

Secure the camera to the camera mount bracketThetiltangleislockeddownwardatshipment.

1Loosenthetiltinglockscrewapprox.1rotationandadjustthetiltangleofthecameratothehorizontalposition.

2Tightenthetiltinglockscrewagainaftertiltangleadjustment.

Note: • Useahexagonalwrenchwithwidthacrossflatsof4mm(locallyprocured)toloosenortighten

thetiltinglockscrew.

3Passeachcableandthesafetywirethroughthecameramountbracket,andsecurethecam-eratothecameramountbracketwiththecamerafixingscrewsx3(accessories).Pass thenetworkcable first through thecameramountbracketbeforepassing through theothercables.

IMPORTANT: • Ensurethatthecamerafixingscrewsarefirmlysecured.

Recommendedtighteningtorque:0.78N·m{0.58lbf·ft}

Camera main body

Safety wire

Network cable

Mounting boss for safety wire

Cable clampDrain slit

Camera mount bracket(accessory)

Camera fixing screw x3 (M4 x 10) (accessories)

Installations/Connections

Tilting lock screw

Camera main bodyHorizontal

Approx. 90 °


21

4Removethescrewsfromthemountingbossofthesafetywireandthemountingbossofthecableclamp.

5Securethesafetywirewiththescrewfromthemountingboss.Then,bundlethewireandthecable using the cable clampand secure themwith each screw from themountingboss asillustrated.

IMPORTANT: • Ensurethatthesafetywireisfirmlysecured.


ConnectionTurnoffacircuitbreakerbeforemakingaconnection.Beforestartingtheconnection,preparetherequireddevicesandcables.

Network cable

RJ-45 (female)

Alarm input/output cable

4P alarm cable (accessory)

Microphone/line input cable (white)

Audio output cable (black)

Power cable(12 V DC)

2P power cable(accessory)

12 V DC (red)GND (black)

LAN cable (category 5 or better, straight, STP)

<Required cable>LAN cable (category 5 or better, straight, STP)

1Connect themicrophone/line inputcableandthemicrophone (foruseof theaudio receptionfunction).Inputimpedance: Approx.2kΩ(unbalanced)Recommendedcablelength: Lessthan1m{3.28'}(formicrophoneinput) Lessthan10m{32.8'}(forlineinput)Recommendedmicrophone: Plug-inpowertypemicrophone(option) Connectamonauralminiplug(ø3.5mm).Supplyvoltage: 2.5V±0.5VRecommendedsensitivityofmicrophone:−48dB±3dB(0dB=1V/Pa,1kHz)Inputlevelforthelineinput: Approx.−10dBV

22

2Connectanexternalamplifier-embeddedspeakertotheaudiooutputcable. Connectastereominiplug(ø3.5mm)(Audiooutputismonaural.). • Outputimpedance:Approx.600Ω(unbalanced) • Recommendedcablelength:Lessthan10m{32.8ft} • Outputlevel:–20dBV * Useanexternalpoweredspeaker.

IMPORTANT: • Connect/disconnecttheaudiocablesandturnonthepowerofthecameraafterturningoffthe

poweroftheaudiooutputdevices.Otherwise,loudnoisemaybeheardfromthespeaker. • Makesurethatthestereominiplugisconnectedtothiscable.Whenamonauralminiplugis

connected,audiomaynotbeheard. Whenconnectingamonauralspeakerwithamplifier,usea locallyprocuredconversioncable

(mono-stereo).

3Connectthealarminput/outputcable.

4Palarmcable

GND (black)

ALARM IN3, AUX OUT (gray) (Terminal 3)

ALARM IN2, ALARM OUT (red) (Terminal 2)ALARM IN1, DAY/NIGHT IN (green) (Terminal 1)

<Ratings>

• ALARMIN1(DAY/NIGHTIN),ALARMIN2,ALARMIN3Inputspecification: No-voltagemakecontactinput(4V-5VDC,internallypulledup)OFF: Openor4V-5VDCON: MakecontactwithGND(requireddrivecurrent:1mAormore)

• ALARMOUT,AUXOUTOutputspecification: Opencollectoroutput(maximumappliedvoltage:20VDC)Open: 4V-5VDCbyinternalpull-upClose: Outputvoltage1VDCorless(maximumdrivecurrent:50mA)*ThedefaultofEXTI/Oterminalsis“Off”.

IMPORTANT: • Besuretousethe4Palarmcableprovidedwiththisproduct. • Off,input,andoutputoftheexternalI/Oterminal2and3canbeswitchedbyconfiguringthe

setting. Refer to theOperating Instructions on the providedCD-ROM for further informationabouttheEXTI/Oterminal2and3(ALARMIN2,3)settings(“Off”,“Alarminput”,“Alarmout-put”or“AUXoutput”).

• WhenusingtheEXTI/Oterminalsastheoutputterminals,ensuretheydonotcausesignalcol-lisionwithexternalsignals.

• Installexternaldevicessothattheydonotexceedtheratingsabove.

23

4ConnectaLANcable(category5orbetter,straight,STP:ForEurope)tothenetworkconnector.

IMPORTANT: • Useall4pairs(8pins)oftheLANcable(category5orbetter,straight,STP:ForEurope). • Themaximumcablelengthis100m{328feet}. • MakesurethatthePoEdeviceinuseiscompliantwithIEEE802.3afstandard. • Whenconnectingboththe12VDCpowersupplyandthePoEdeviceforpowersupply,12V

DCwillbeusedforpowersupply*. *Ifa12VDCpowersupplyandaPoEhuborrouterareusedatthesametime,networkcon-

nectionsmaynotbepossible.Inthiscase,disablethePoEsettings. RefertotheoperatinginstructionsofthePoEhuborrouterinuse. *Inthesituationwherea12VDCpowersupplyandaPoEhuborrouterareusedatthesame

timeandthe12VDCpowersupplyisthendisconnected,thepowersupplymaybestoppedandthecameramayrestartdependingonthePoEhuborrouterused.

• WhentheLANcableisdisconnectedonce,reconnectthecableafteraround2seconds.Whenthecableisquicklyreconnected,thepowermaynotbesuppliedfromthePoEdevice.

• Whencablesareusedoutdoors, there isachancethat theymaybeaffectedby lightning. Inthiscase,installalightningarresterjustbeforewherethecablesconnecttothecamera.

5Connectthepowercable.

Caution: • A READILY ACCESSIBLE DISCONNECT DEVICE SHALL BE

INCORPORATEDTOTHEEQUIPMENTPOWEREDBY12VDCPOWERSUPPLY.

ConnecttheoutputcableoftheACadaptertothe2Ppowercable.

IMPORTANT: • The12VDCpowersupplyshallbeinsulatedfromthecommercialACpower. • Besuretousethe2Ppowercableprovidedwiththisproduct. • Besuretofullyinsertthe2Ppowercableintothe12VDCpowersupplyterminal.Otherwise,it

maydamagethecameraorcausemalfunction. • Wheninstallingthecamera,makesurethatexcessiveforceisnotappliedtothepowercable.

Power cable 12VDCRed PositiveBlack Negative

24

Waterproof treatment for the cable joint sectionsAdequatewaterproof treatment is required for thecableswhen installing thecamerawithcablesexposedorinstallingitundertheeaves.Thecamerabodyiswaterproof,butthecableendsarenotwaterproof.Besuretousethesuppliedwaterprooftape(accessory)atthepointswherethecablesareconnect-edtoapplywaterprooftreatmentinthefollowingprocedure.Failuretoobservethisoruseofatapeotherthantheprovidedwaterprooftape(suchasavinyltape)maycausewaterleakageresultinginmalfunction.

LAN cable

Alarm input/output cable, power cable, microphone/ line input cable, audio output cable

Wind the tape in a half-overlapping manner.

IMPORTANT: How to wind the supplied waterproof tape

• Alsowaterproofthe2Ppowercable,4Palarmcable,andexternalconnectionsinthesameway.

• Stretchthetapebyapprox.twice(seetheillustration)andwind it around the cable. Insufficient tape stretch causesinsufficientwaterproofing.

• Toprevent theLANcablehook fromcoming looseeasily,fittheLANcablecoverontothepigtailcableasillustrated,andthenslideitinthedirectionindicatedbythearrow.The connector of the LAN cable used with this cameramustmeetthefollowingrestrictions.Heightwheninserted(Frombottomtohook.):Max.16mm{5/8inches}Connectorwidth:Max.14mm{9/16inches}

• Toinstallthisproductoutdoors,besuretowaterproofthecables. Waterproof grade (IEC IP66 or equivalent) isappliedtothisproductonlywhenitisinstalledcorrectlyasdescribed in theseoperating instructionsandappropriatewaterprooftreatmentisapplied.Theinternalpartsofbasebracketsarenotwaterproofed.

Wind the tape in a half-overlapping manner.

2x

LAN cable cover

The hook engages with the connector terminal

Stretch the tape to about twice.

25

Connection example when connecting to a network using a PoE hub

<Required cable>LANcable(category5orbetter,straight,STP:ForEurope)UseaLANcable(category5orbetter,cross)whendirectlyconnectingthecameratoaPC.*Recommendedcablelengthfromthespeaker:lessthan10m{32.8feet}Recommendedcablelengthfromthemicrophone:lessthan1m{3.28feet}

IMPORTANT: • Theadjustmentmonitorisusedforcheckingtheadjustmentoftheangularfieldofviewwhen

installingthecameraorwhenservicing.Itisnotprovidedforrecording/monitoringuse. • Dependingonthemonitor,somecharacters(cameratitle,presetID,etc.)maynotbedisplayed

onthescreen. • Useaswitchinghuborarouterwhichiscompliantwith10BASE-T/100BASE-TX. • IfaPoEhubisnotused,eachnetworkcameramustbeconnectedtoa12VDCpowersupply. • Whenusing12VDC,powersupplyfromaPoEhuborrouterisnotrequired. • Networkcamera is intendedforconnectiontoanethernetorPoEnetworkwithoutroutingto

theoutsideplant.

Powered speaker

Powered speaker

Recommended total extended cable length*

Adjustment monitor

Adjustment monitor

LAN cable(category 5 or better, straight, STP: For Europe)

LAN cable (category 5 or better, straight, STP: For Europe)

LAN cable(category 5 or better,straight, STP: For Europe)

Microphone

PoE device (hub)

PC

Microphone

26

Secure the camera mount bracket when the camera is directly installed on a wall

Use4screws(locallyprocured)tosecurethecameramountbrackettoawallorajunctionbox(locallyprocured).Requiredpull-outcapacityofasinglescrew/boltis196N{44.06lbf}ormore.

• Ifajunctionboxisused,puttingtheboxessidebysideisrecommendedasillustrated.(Useunusedjunctionboxestopasscablesthroughforeasy

cabling.)

When the camera is installed on a wall using the adapter box1Use4screws(locallypro-

cured)tosecuretheadapt-erbox(accessory)toawallorajunctionbox(locallyprocured).Requiredpull-outcapacityofasinglescrew/boltis196N{44.06lbf}ormore.

TOP

6 mm (W) x 10 mm (L) {1/4" (W) x 3/8" (L)} (long hole)



46 mm {1-13/16"}83.5 mm{3-1/4"}

46 mm{1-13/16"}

20 mm {13/16"}

Cable access hole

Adapter box (accessory)

Cable access hole (used for wiring)(The female thread for conduit is compliant with ANSI NPSM (parallel pipe threads) 3/4 or ISO 228-1 (parallel pipe threads) G3/4.)

Mounting screw x4(locally procured)

83.5

mm

{3-1

/4"}

View from above (internal)

Unusedjunction boxes

Junction boxes



Cable access hole



46 mm{1-13/16"}

20 mm{13/16"}

83.5

mm

{3-1

/4"}

27

• Ifajunctionboxisused,puttingtheboxessidebysideisrecommendedasshownintheillustrationatright.(Useunusedjunctionboxestopasscablesthroughforeasycabling.)

2Attachthecameramountbrackettotheleftorrighthingesofadapterbox.

IMPORTANT: • Ensurethattheadapterboxmountingscrews

(accessory)arefirmlysecured.Recommendedtighteningtorque:M4:0.78N·m{0.58lbf·ft}

• Ensurethatthemountingscrewsforadapterbox/cameramountbracket(accessory)arefirmlysecured.Recommendedtighteningtorque:M5:1.86N·m{1.37lbf·ft}

Note: • Therightorlefthingesoftheadapter

boxshallbeselectedsoastopreventthemotionofthecameramountbracketfrombeinginterferedwithbyobstruc-tionssuchasawallwhenthecameramountbracketisconnectedtothehing-esoftheadapterbox.

TOP


View from above (internal)

Adapter box mounting screw (M4 x 35)(accessory)

Hinges

Adapter box (accessory)


Mounting screw for adapter box/camera mount bracket x4 (M5 x 20) (accessories)

Unused junction boxes

Junction boxes


46 mm{1-13/16"}83.5 mm

{3-1/4"}

28

3Securethemountbracketcoverx2(accessories)tothecameramountbracketwiththe2mountbracketcoverscrews(accessories).

IMPORTANT: • Ensurethatthemountbracketcover

screwsarefirmlysecured.Recommendedtighteningtorque:0.59N·m{0.44lbf·ft}

Mount bracket cover x2 (accessories)


Mount bracket cover screw x2 (M3 x 6) (accessories)

29

IMPORTANT: • BeforeinsertinganSDmemorycard,makesuretoturnoffthepower. • WheninsertinganSDmemorycard,makesurethedirection. • BeforeremovingtheSDmemorycard,makesuretoselect“Notuse”for“SDmemorycard”on

the [SD memory card] tab of the “Basic” page on the setup menu first. (☞ OperatingInstructions(includedintheCD-ROM))

1Loosenthe4fixingscrewsofthefrontcovertoremovethefrontcover.

2Insert an SD memory card fully into the SDmemorycardslotuntilaclickisheard.

3Attachthefrontcovertothecamera. (☞page33)

4Whenremoving theSDmemorycard fromtheSDmemorycardslot,detachthefrontcoverbyfollowingstep1,andpushthecarduntilaclickisheard.AftertheSDmemorycardisremoved,attachthefrontcovertothecameraagain.

(☞page33)

Insert/remove an SD memory card

Label side

<WV-SPW631L>

30

1 Besuretoviewthemonitorforadjustmentwhenthecameraangleisadjusted.

Supplypower to thisunit, connect themonitor foradjustment (e.g.asmall LCD) to themonitoroutputjack,andadjustthecameraangle(turnoffthepowerafterviewangleadjustmentforsafety).

qLoosenthe4fixingscrewsofthefrontcovertoremovethefrontcover.wConnect themonitor output jack and themonitor for adjustmentwith theRCApin cable

(locallyprocured).

<Front cover>(ThisillustrationrepresentsWV-SPW611.)

eRepeatthesteps(1)and(2)toadjustthecameraangle.(1)Loosenthepanninglockscrewandrotatethecameraheadhorizontallytoadjustpanning.(2)Loosenthetiltinglockscrewandrotatethecameraheadverticallytoadjusttilting.(3)Tightenthepanninglockscrewandtiltinglockscrewaftercameraangleadjustment.

IMPORTANT: • Aftercameraangleadjustment,thepanninglockscrewandtiltinglockscrewshallbesecurelytightened.


Notes: • Useahexagonalwrenchwithwidthacrossflatsof4mm(locallyprocured)toloosenortighten

thepanninglockscrewandtiltinglockscrew. • Approximately 1 rotation of loosening the panning lock screw and tilting lock screw allows

cameraangleadjustment.Donotloosenthescrewsbeyondnecessity. • Thecamerabodyshallbeheldwhenthepanninglockscrewortiltinglockscrewisloosened. • Focusadjustment (☞ page31-32)shallbeperformedat thesame timepanningand tilting

adjustmentsareperformed.

Adjustment

Front cover

Fixing screw x4 Monitor output jack

Tilting lock screw

Panning lock screw

31

2Adjusttheangularfieldofviewandthefocus. Adjusttheangularfieldofviewinaccordancewiththedistancebetweenthecameralensanda

photographicsubject.Theseadjustmentsshallbeperformedtogetherwith thecameraangleadjustment.

(ThisillustrationrepresentsWV-SPW611.)

When adjusting the angular field of view and the focus from the setup menuRefertotheOperatingInstructions(includedintheCD-ROM)forhowtoperformthemanualfocusadjustmentfromthesetupmenu.

When adjusting the angular field of view and the focus with the panel of the cameraq Press theTELEorWIDEbuttons tomove the knobbetweenTELEandWIDE toobtain the

appropriateangularfieldofview.

Note: • Whilethebuttonishelddown,theangleoftheviewmovesinthe"T"or"W"direction. • WhentheangularfieldofviewisadjustedontheTELEside,opticalzoomisapplieduntil3.2x,

andifthereareanyadjustmentsabovethis,extraopticalzoomisapplied. • Whentheimagecapturesizeunder"VGA"isapplied,thezoomfactorcanbeadjustedupto

2xwithoutdeteriorationofimagequality. • Thezoomingfactorisdisplayedonthetoprightofthescreen. • WhenusingtheTELEorWIDEbuttonstoperformoperations,thezoomfactorstopsonceat3.2x.If

operationsarecontinued,theangleoftheviewcanbemovedevenmoreinthe"T"or"W"directions.

w Whentheautofocus(AF)buttonispressed,theautofocus(AF) indicatorwill lightforaround10seconds,andthefocusisautomaticallyadjusted.

IMPORTANT: • Donottouchthelens. • Defocusmay be caused by the reinstalled front cover. In this case, perform the auto focus

functionfromthesetupmenu.

Auto focus (AF) button

TELE button

WIDE button

32

Note: • When shooting in the following place or the following subjects, focusmay not be adjusted

automatically. In this case, adjust the focus manually from the setup menu. Refer to theOperatingInstructions(includedintheCD-ROM)forhowtoperformthemanualfocusadjust-mentfromthesetupmenu.

• Subj.withlargeilluminancechange • Subj.movingfrequently • Subj.withreflectionorextrabrightness • Subj.withlowilluminance • Placewherethefrontcovereasilybecomesdirty • Subj.throughawindow • Subj.withlesscontrastsuchaswhitewall • Subj.withheavyflicker

• Ifthe2xextraopticalzoomisappliedwhen"1280x960","1280x720"isselectedfortheimagecapturesize,theimagequalitywillbedeterioratedbecausetheeffectofExtraOpticalZoomisnotprovided.

• When images in thenear-infrared lightareachange fromcolor toblack&white,out-of-focusmaybeoccurredaccordingtothenatureofopticalproperty.Inthiscase,thefocuscanauto-matically be corrected by selecting "Auto" or "Preset" for "Adjustingmethod" on the setupmenu (The focuswillnotautomaticallybeadjustedaccordingtothe illumination levelchangeoncethefocusiscorrected.)RefertotheOperatingInstructions(includedintheCD-ROM)forhowtoset"Adjustingmethod"onthesetupmenu.

33

Mountthefrontcover.

IMPORTANT: • Thetighteningtorquedescribedbelowshallbefollowedforthe4fixingscrewsoffrontcover. Recommendedtighteningtorque:0.59N·m{0.44lbf·ft} • Thetighteningsequenceofthe4fixingscrewsofthefrontcovershallbeobservedandrepeat-

edtwiceasdescribedintheillustrationabove. ((1)→ (2)→ (3)→ (4),twice) • Makesure thepackinghasnotcomeofforbecomeaskew. If thishappensput itback into

place. • Makesurethepackinghasnodustorothercontaminantsonit.Removeanydustorcontami-

nantsonthepacking. • Removethecoverfilmfromtheclearpartofthefrontcoversectionaftertheinstallationiscomplete.

Donottouchtheclearpartofthefrontcoversectionbyhanddirectlyafterremovingthecoverfilm.

Mounting the front cover

(3) (1)

(2) (4)

Fixing screw x4

34

Attaching the mounting surface on the top surface of the camera body

Whenthemountingsurfaceischangedtothetopsurfaceofthecamerabody

1Removethe4sunshieldfixingscrewsfromthecamerabodyandremovethesunshield.

2Removethe4tripodheadfixingscrewsfromthecamerabodyandremovethetripodhead.

3Loosenthefixingscrewx1andremovetherearcover,andremovethecap.

4Rotateeachcableinthedirectionofthearrow(clockwise)asillustratedandpassthembetweenopeningintheuppergrooveofthemainbody.

Then,attachthecaptothelowergroove,andsecuretherearcoverwiththefixingscrewx1.

Attachtherearcovertothefrontcoverbyhookingattachmenthole1oftherearcovertothetabonthefrontcoverwhilepassingtheprotrusionofthefrontcoverthroughattachmenthole2oftherearcover.

Tab Protrusion

Upper groove

Attachment hole 1

Attachment hole 2Cap

Tripod head fixing screw x4

Rear cover Fixing screw x1

Tripod head

35

5 Mountthetripodheadonthetopofthecamerabodywiththe4tripodheadmountingscrewsthatwereremovedinthestep2.

IMPORTANT: • Cautionshallbetakentopreventeachcablefrombeingcaughtbetweenthecamerabodyand

tripodhead. • Besuretousethescrewsthatwereremovedfromthetripodhead. Recommendedtighteningtorque:0.59N·m{0.44lbf·ft}

6 Securethecameratothecameramountbracketwiththecamerafixingscrewsx3.Passeachcableandthesafetywirethroughthecameramountbracket,andconnectthesafe-tywiretothecameramountbracket.Then,bundlethewireandthecableusingthecableclampandsecurethemwitheachscrewfromthemountingbosstothecameramountbracket(☞page20-21).

IMPORTANT: • Besuretousethescrewsthatwereremovedfromthecameramountbracket. Recommendedtighteningtorque:0.78N·m{0.58lbf·ft} • Besuretousethescrewsthatwereremovedfromthesafetywire. Recommendedtighteningtorque:0.59N·m{0.44lbf·ft}

Tripod head fixing screw x4 (M3x10)

Camera fixing screw x3 (M4 x 10) (accessories)


Camera main body

36

7 Removethesunshieldbackside.

Asillustrated,openingupthesunshieldinbothdirectionsmakesiteasiertoremovetherearpartofthesunshield.• Wheninstallingthecameratoaceiling,therearpartofthesunshieldandthefixingscrewsarenotused.

8 Mountthesunshieldonthecamerabodywiththe4sunshieldmountingscrewsafterremovingthesunshieldbackside.

• Thesunshieldisattachedtothecamerabyinsertingtheprotrusionsontherearcoverofthecameraintotheattachmentholesontherearpartofthesunshield.

IMPORTANT: • Besuretousethescrewsthatwereremovedfromthesunshield. Recommendedtighteningtorque:0.59N·m{0.44lbf·ft}

Fixing screw x2

Rear part of sunshield

Attachment hole

ProtrusionRear part of sunshield

37

Configure the network settings

Configuring the camera so that it can be accessed from a PCThefollowingaredescriptionsforwhenthecamerawithdefaultsettingsisconfigured.IfyouareusingfirewallsoftwareonyourPC,theSetupProgrammaynotbeabletofindanycamerasonyournetwork.Configurethesettingofthecameraaftertemporarilyinvalidatingthefirewallsoftware.ContactthenetworkadministratororyourInternetserviceproviderforinformationaboutconfiguringthesettingsofthenetwork.

1InserttheprovidedCD-ROMintotheCD-ROMdriveofyourPC. • TheLicenseAgreementwillbedisplayed.ReadtheAgreementandchoose“Iacceptthe

terminthelicenseagreement”,andclick[OK]. • The launcherwindowwill be displayed. If the launcherwindow is not displayed, double

clickthe“CDLauncher.exe”fileontheCD-ROM.

Note: • Referto“UsingtheCD-ROM” intheOperating InstructionsontheprovidedCD-ROMfor fur-

therinformationaboutCDLauncher.

2Clickthe[Run]buttonnextto[IPSettingSoftware]. [PanasonicIPSetting]screenwillbedisplayed.Clickthe[NetworkSettings]buttonafterselect-

ingtheMACaddress/IPaddressofthecameratobeconfigured.

38

3Selectthecamerayouwanttoconfigure,andclick[AccessCamera].

Note: • When cameras are displayed in [Panasonic IP Setting] screen, click the camera with same

MACaddressastheMACaddressprintedonthecamerathatyouwanttoconfigure.

4Iftheinstallationscreenoftheviewersoftware“NetworkCameraView4S”isdisplayed,followtheinstructionsofthewizardtostarttheinstallation.(Theviewersoftwareisinstalledfromthecamera.)

• The“Live”pagewillbedisplayed. • Ifyoucannotinstalltheviewersoftware“NetworkCameraView4S”orifimagesarenot

displayed,clickthe[Install]buttonnextto[ViewerSoftware]onthelauncherwindowtoinstallthesoftware.

• Performthe[Time&date]settingsinthe“Setup”-“Basic”pagebeforeusingthecamera.

Note: • Whennoimageisdisplayedonthe“Live”page,refertotheTroubleshootingintheOperating

InstructionsontheprovidedCD-ROM. • It ispossibletoenhancethenetworksecuritybyencryptingtheaccesstocamerasusingthe

HTTPSfunction.RefertotheOperatinginstructionsontheprovidedCD-ROMforhowtocon-figuretheHTTPSsettings.

• Clickthe[Setup]buttononthe“Live”page,theuserauthenticationwindowwillbedisplayed.Enterthedefaultusernameandpasswordasfollows,andlogin.

Username:admin Password:12345 • Whenchangingsettingsrelatedtothenetworksettings,suchasconnectionmode,IPaddress,

and subnet mask, click the [Network Settings] button in [Panasonic IP Setting] screen asshowninstep3,thenchangeeachsetting.

• Duetosecurityenhancementsin“IPSettingSoftware”,“Networksettings”ofthecameratobecon-figuredcannotbechangedwhenaround20minuteshavepassedafterturningonthepowerofthecamera.(Whentheeffectiveperiodissetto“20min”inthe“EasyIPSetupaccommodateperiod”.)

However,settingscanbechangedafter20minutesforcamerasintheinitialsetmode. • “Network Camera Recorder with Viewer Software Lite” which supports live monitoring and

recordingimagesfrommultiplecamerasisavailable.Forfurtherinformation,refertoourweb-site(http://security.panasonic.com/pss/security/support/info.html).

39

Before asking for repairs, check the symptoms with the following table. Contactyourdealerifaproblemcannotbesolvedevenaftercheckingandtryingthesolutioninthetableoraproblemisnotdescribedbelow.

Symptom Cause/solutionReference

pages

Power is not turned on.

When using DC power supply • Is12VDCpowersupplyconnectedtothe2P

powersupplycable? → Checkwhethertheconnectionisappro-

priatelyestablished. • Is the AC adapter in use compliant with the

Specifications? → Check the Specifications regarding AC

adapter.When using a PoE device for power supply • ArethePoEdeviceandthenetworkcableof

thecameraconnectedusingaLANcable? → Checkwhethertheconnectionisappro-

priatelyestablished. • DependingonthePoEdevice,thepowersup-

plywillstopwhenthedemandedpowerexceedsitstotalpowerlimitforallPoEports.

→ RefertotheoperatinginstructionsofthePoEdeviceinuse.

21-23

When the IR LED lights a part or all of the screen appears blurred.

• Isthereawallorotherreflectingsurfaceorobjectnearthecamera(includingareasnotdisplayedinimages)?SPW631LT SPW631L SPW611L

→ AdjustthecameraanglesothatlightfromtheIRLEDisnotreflected.

30-32

When the IR LED lights the camera switches between color mode and black-and-white mode.

• Thesubjectmaybetooclosetothecamera.SPW631LT SPW631L SPW611L

→ Adjustthedistancebetweenthecameraandthesubject.

30-32

Troubleshooting

40

Symptom Cause/solutionReference

pages

The LINK indicator does not light in orange even when the network cable is connected to the camera.

• IstheLANcableconnectedappropriately? → ConnecttheLANcableappropriately. • Isthehuborrouterconnectedtothecamera

operatingappropriately? → Checkifthehuborrouterinuseisoperat-

ingappropriately. • Isn'ttheLANcableconnectedtothecamera

broken? → Replacethecablewithanotherone.

23-25

AF/SD ERROR indicator lights red or blinks red.

• Isn’tthewriteprotectswitchoftheinsertedSDmemorycardsetto“LOCK”?

→ UnlockthewriteprotectswitchoftheSDmemorycard.

• Hasn'ttheinsertedSDmemorycardbeenfor-mattedonaPC?

→ UseanSDmemorycardformattedonthecamera.

OrinstallthesoftwaretoformattheSDmemorycardonthePC.Refertoourwebsite(http://security.panasonic.com/pss/security/support/info.html)forfurtherinformationaboutthesupportedsoftware.

• Isn'ttheinsertedSDmemorycardfaulty? → Replacethecardwithanormalone.

OperatingInstructions(includedintheCD-ROM)

41

• BasicWV-SPW631LT/WV-SPW631L/

WV-SPW611L WV-SPW611

Powersource*1: 12VDC±10%,PoE(IEEE802.3afcompliant:DC36-57V)Powerconsumption*1:(PoE:Class0device)

DCpowersupply:12VDC/1080mA/Approx.12.9WPoEDevice:48VDC/360mA/Approx.12.95W

DCpowersupply:12VDC/670mA/Approx.8.1WPoEDevice:48VDC/230mA/Approx.11.1W

Ambientoperatingenviron-ment: –40°Cto+50°C

{–40°Fto122°F}*2

Ambientoperatinghumidity: 10%to90%(nocondensation)IRLEDirradiationdistance: 30m{98.43feet} –Monitoroutput(foradjust-ment):

VBS:1.0V[p-p]/75Ω,composite,RCAjackAnNTSCorPALmonitorcanbeconnectedtothecamera(usetheselectorswitchorsoftwaretoselectthemonitortype).

ExternalI/Oterminals: ALARMIN1(DAY/NIGHTIN)/ALARMIN2(ALARMOUT)/ALARMIN3(AUXOUT)(x1each)DAY/NIGHTIN,ALARMOUT,andAUXOUTcanbeusedbychangingthesettingsofTerminal1,Terminal2,andTerminal3.

Microphone/lineinput: ø3.5mmmonauralminijackInputimpedance:Approx.2kΩ(unbalanced)

Formicrophoneinput: Applicablemicrophone:Plug-inpowertypeSupplyvoltage:2.5V±0.5VRecommendedsensitivityofmicrophone:–48dB±3dB(0dB=1V/Pa,1kHz)

Forlineinput: Inputlevel:Approx.–10dBVAudiooutput: ø3.5mmstereominijack(monauraloutput)

Outputimpedance:Approx.600Ω(unbalanced)ExternalspeakerwithanamplifierOutputlevel:-20dBV

Waterproof*3: Mainbody:IP66(IEC60529),Type4X(UL50),NEMA4XcompliantDimensions: 94mm(W)x89mm(H)x226mm(L){3-45/64inches(W)x

3-1/2inches(H)x8-57/64inches(L)}Mass: Approx.1.4kg{3.09lbs}Finish: Mainbody:Aluminumdiecast/resin,metallicsilvercoating

Frontcoversectionclearpart:Polycarbonateresin

*1Refertoourwebsite(http://security.panasonic.com/pss/security/support/info.html)forfurtherinfor-mationaboutPowersourceandPowerconsumptioninformation.

*2Whenusingthisproductwithoutturningthepoweroff.(However,thetemperatureinsidethecamerashallbe-10°C{14°F}orhigher.)Performsettingsorstartupoperationswhentheambienttemperatureis-30°C{-22°F}orhigher.Theautofocusfunctionisnotavailableuntiltheheaterunitofthecameraraisestheinternaltemperatureofthecamera.

*3Onlywheninstallationworkisproperlyperformedaccordingtotheinstructionsinthisbookandappropriatewaterprooftreatmentisperformed.

Specifications

42

• CameraImagesensor: SPW631LT SPW631L

Approx.1/2.8typeMOSimagesensorSPW611L SPW611

Approx.1/3typeMOSimagesensorBuilt-inprimarycolorfilter

Effectivepixels: SPW631LT SPW631L

1944(H)x1213(V)Approx.2.4megapixelsSPW611L SPW611

1296(H)x1032(V)Approx.1.3megapixelsScanningarea: SPW631LT SPW631L

5.346mm(H)x3.336mm(V){7/32inches(H)x1/8inches(V)}SPW611L SPW611

4.864mm(H)x3.891mm(V){3/16inches(H)x5/32inches(V)}Scanningsystem: ProgressiveMinimumillumination: SPW631L

Color:0.04lx{0.00372foot-candle} (F1.3,Maximumshutter:Off(1/30s),AGC:High) 0.003lx{0.00028foot-candle} (F1.3,Maximumshutter:max.16/30s,AGC:High)*BW :0lx{0.000foot-candle}(F1.3,Maximumshutter:OFF (1/30s),Gain:High,whentheIRLEDislit) 0.01lx{0.00093foot-candle} (F1.3,Maximumshutter:Off(1/30s),AGC:High) 0.0007lx{0.00007foot-candle} (F1.3,Maximumshutter:max.16/30s,AGC:High)*

SPW631LT

Color:0.06lx{0.00558foot-candle} (F1.6,Maximumshutter:Off(1/30s),AGC:High) 0.004lx{0.00037foot-candle} (F1.6,Maximumshutter:max.16/30s,AGC:High)*BW :0lx{0.000foot-candle}(F1.6,Maximumshutter:OFF (1/30s),Gain:High,whentheIRLEDislit) 0.02lx{0.00186foot-candle} (F1.6,Maximumshutter:Off(1/30s),AGC:High) 0.002lx{0.00019foot-candle} (F1.6,Maximumshutter:max.16/30s,AGC:High)*

SPW611L SPW611

Color:0.01lx{0.00093foot-candle} (F1.3,Maximumshutter:Off(1/30s),AGC:High) 0.0007lx{0.00007foot-candle} (F1.3,Maximumshutter:max.16/30s,AGC:High)*BW :0lx{0.000foot-candle}(F1.3,Maximumshutter:OFF (1/30s),Gain:High,whentheIRLEDislit) 0.003lx{0.00028foot-candle} (F1.3,Maximumshutter:Off(1/30s),AGC:High) 0.0002lx{0.00002foot-candle} (F1.3,Maximumshutter:max.16/30s,AGC:High)**Convertedvalue

43

Super-Dynamic: On(High)/On(Normal)/Off*Whenframerateissetto60fps,OffisdisplayedforSuperDynamicfunction.

Dynamicrange: 133dBtyp.(SuperDynamic:On)FaceSD(Super-Dynamic): On/Off(onlywhenSuperDynamic:On)Gain(AGC): On(Low)/On(Mid)/On(High)/OffAdaptiveblackstretch: On/Off(onlywhenSuperDynamic:Off)Backlightcompensation(BLC): On/Off(onlywhenSuperDynamic:Off)Fogcompensation: On/Off(onlywhenSuperDynamic/Adaptiveblackstretch:Off)Highlightcompensation(HLC): On/Off(onlywhenSuperDynamic/Backlightcompensation:Off)Lightcontrolmodesetting: Outdoorscene/Indoorscene(50Hz)/Indoorscene(60Hz)/Fix

shutterShutterspeed: [2megapixel[16:9](60fpsmode) SPW631LT SPW631L /

1.3megapixel[16:9](60fpsmode) SPW611L SPW611 ]OFF(1/60),1/100,1/120,1/250,1/500,1/1000,1/2000,1/4000,1/10000Otherthan[2megapixel[16:9](60fpsmode) SPW631LT SPW631L /1.3megapixel[16:9](60fpsmode) SPW611L SPW611 ]OFF(1/30),3/100,3/120,2/100,2/120,1/100,1/120,1/250,1/500,1/1000,1/2000,1/4000,1/10000

Maximumshutter: max.1/1000s,max.1/500s,max.1/250s,max.1/120s,max.2/120s,max.1/100s,max.2/100s,max.1/60s,max.1/30s,max.2/30s,max.4/30s,max.6/30s,max.10/30s,max.16/30s

Color/BW: Off/On/Auto1(Normal)/Auto2(IRLight)/Auto3(SCC)IRLEDLight: SPW631LT SPW631L SPW611L

High/Mid/Low/OffWhitebalance: ATW1/ATW2/AWCDigitalnoisereduction: High/LowPrivacyzone: On/Off(upto8zonesavailable)Cameratitleonscreen: On/Off

Upto20characters(alphanumericcharacters,marks)VideoMotionDetection(VMD): On/Off,4areasavailable

• LensZoomratio: SPW631LT

2.4xVarifocalLensSPW631L SPW611L SPW611

3.6xVarifocalLensSPW631L

10.8xExtraopticalzoom*isavailable.*16:9modemustbeselectedSPW631LT* SPW611L SPW611

7.2xExtraopticalzoomisavailable.*16:9modemustbeselected

44

Digital(electronic)zoom: Choosefrom3levelsofx1,x2,x4Focallength: SPW631LT

9mm–22mm{23/64inches–55/64inches}SPW631L SPW611L SPW611

2.8mm–10mm{1/8inches–13/32inches}Maximumapertureratio: SPW631LT

1:1.6(WIDE)–1:3.0(TELE)SPW631L SPW611L SPW611

1:1.3(WIDE)–1:3.0(TELE)Focusrange: SPW631LT

1.0m–∞SPW631L SPW611L SPW611

0.3m–∞Aperturerange: SPW631LT

F1.6–F11SPW631L SPW611L SPW611

F1.3–F11Angularfieldofview: SPW631LT

[16:9mode]Horizontal:13.8°(TELE)–33.5°(WIDE)Vertical:7.7°(TELE)–18.1°(WIDE)[4:3mode]Horizontal:11.5°(TELE)–27.4°(WIDE)Vertical:8.6°(TELE)–20.1°(WIDE)SPW631L

[16:9mode]Horizontal:30.9°(TELE)–105.4°(WIDE)Vertical:17.4°(TELE)–57.3°(WIDE)[4:3mode]Horizontal:25.8°(TELE)–86.4°(WIDE)Vertical:19.3°(TELE)–63.9°(WIDE)

SPW611L SPW611[16:9mode]Horizontal:28.4°(TELE)–96.2°(WIDE)Vertical:16.1°(TELE)–52.8°(WIDE)[4:3mode]Horizontal:28.4°(TELE)–96.2°(WIDE)Vertical:21.4°(TELE)–71.0°(WIDE)

• Camera Mount bracketAdjustingangle: Horizontal:±100°

Vertical:+30°~-90°Dimensions: 125mm(W)x125mm(H)x108mm(L)

{4-15/16inches(W)x4-15/16inches(H)x4-1/4inches(L)}

45

Mass: Approx.220g{0.49lbs}Finish: Aluminumdiecast,metallicsilvercoating

<Camera mount bracket dimensional drawing> (unit : mm)125 11446

4-6 (W) x 10 (L)33

.5108

8020

ø2645

°

121

83.5125

ø36

• NetworkNetwork: 10BASE-T/100BASE-TX,RJ-45connectorResolution:H.264JPEG(MJPEG)

SPW631LT SPW631L

2megapixel[16:9](30fpsmode)/2megapixel[16:9](60fpsmode)1920x1080,1280x720,640x360,320x180,160x902megapixel[4:3](30fpsmode)1600x1200,1280x960,800x600,VGA,400x300,QVGA,160x1203megapixel[4:3](30fpsmode)*Usedbysuperresolutiontechniques2048x1536,1280x960,800x600,VGA,400x300,QVGA,160x120

SPW611L SPW611

1.3megapixel[16:9](30fpsmode)/1.3megapixel[16:9](60fpsmode)1280x720,640x360,320x180,160x901.3megapixel[4:3](30fpsmode)1280x960,800x600,VGA,400x300,QVGA,160x120

46

Imagecompressionmethod: H.264*1Imagequality(Constantbitrate/Besteffort):Low(Motionpriority)/Normal/Fine(Imagequalitypriority)(VBR):0Superfine/1Fine/2/3/4/5Normal/6/7/8/9LowTransmissiontype:Unicast/MulticastVideobitrate:(Constantbitrate/VBR/Framerate/Besteffort/AdvancedVBR)64kbps/128kbps*/256kbps*/384kbps*/512kbps*/768kbps*/1024kbps*/1536 kbps*/2048kbps*/3072kbps*/4096kbps*/6144kbps*/8192kbps*/10240kbps*/12288kbps*/14336kbps*/16384kbps*/20480kbps*/24576kbps*/30720kbps*/40960kbps**TheavailablerangeoftheH.264bitratevariesdependingonthesettingselectedfor“Imagecapturesize”.(Framerate)1fps/3fps/5fps*/7.5fps*/10fps*/12fps*/15fps*/20fps*/30fps*/60fps*

*"Framerate*"islimitedto"Maxbitrate(perclient)".Whenavaluewithanasterisk(*)ontherightofitisselected,theactualframeratemaybelowerthatthevalueselected.JPEG(MJPEG)Imagequality:0SUPERFINE/1FINE/2/3/4/5NORMAL/6/7/8/9LOW(10steps:0-9)

Transmissioninterval: 0.1fps-60fps(JPEGframeratewillberestrictedwhendisplayingbothJPEGandH.264images.)

Croppingfunction: •Off/JPEG(1)/JPEG(2)/JPEG(3)/H.264(1)/H.264(2)/H.264(3)/H.264(4)/H.264(all)

•AlarmactionOn/OffAudiocompressionmethod: G.726(ADPCM)32kbps/16kbps,G.71164kbps,AAC-LC*2

Bandwidthcontrol: Unlimited/64kbps/128kbps/256kbps/384kbps/512kbps/768kbps/1024kbps/2048kbps/4096kbps/8192kbps

Protocol: IPv6:TCP/IP,UDP/IP,HTTP,HTTPS,FTP,SMTP,DNS,NTP,SNMP,DHCPv6,RTP,MLD,ICMP,ARP

IPv4:TCP/IP,UDP/IP,HTTP,HTTPS,RTSP,RTP,RTP/RTCP,FTP,SMTP,DHCP,DNS,DDNS,NTP,SNMP,UPnP,IGMP,ICMP,ARP

OS*3: MicrosoftWindows8.1MicrosoftWindows8MicrosoftWindows7MicrosoftWindowsVista

Browser*3: WindowsInternetExplorer11(32-bit)WindowsInternetExplorer10(32-bit)WindowsInternetExplorer9(32-bit)WindowsInternetExplorer8(32-bit)WindowsInternetExplorer7(32-bit)

Maximumconcurrentaccessnumber:

14(Numberofsessionsthatcanconnecttocamerasatthesametime)*Dependsonnetworkconditions

FTPclient: Alarmimagetransmission,FTPperiodictransmission(WhentheFTPtransmissionisfailed,backuponanoptionalSDmemorycardisavailable.)

47

Multi-screen: Upto16cameraimagescanbedisplayedsimultaneouslyonamulti-screen.(Includingthecameraitself)

CompatibleSDXC/SDHC/SDmemorycard*4:

ManufacturedbyPanasonic(SDspeedclass4orhigher)SDXCmemorycard:64GBSDHCmemorycard:4GB,8GB,16GB,32GBSDmemorycard:2GB(exceptminiSDcardandmicroSDcard)

Cellularphonecompatibility: JPEGimage,AUXcontrol(byaccesslevel)Mobileterminalcompatibility:(AsofAugust,2014)*5

iPad,iPhone,iPodtouch(iOS4.2.1orlater)AndroidTMmobileterminals

*1Transmissionfor4streamscanbeindividuallyset.*2AAC(AdvancedAudioCoding-LowComplexity)isonlyusedwhenrecordingaudioonanSDmemorycard.

*3ForfurtherinformationaboutPCsystemrequirementsandprecautionsforwhenusingMicrosoftWindows8.1,MicrosoftWindows8,MicrosoftWindows7,MicrosoftWindowsVista,orWindowsInternetExplorer,click“Manual”-“Open”fromthesuppliedCD-ROMandreferto“NotesonWindows®/InternetExplorer®versions”.

*4WhenusinganSDmemorycardsupportingClass10ofthespeedclass,useaUHS-I(UltraHighSpeed-I)compliantcard.

*5Forfurtherinformationaboutcompatibledevices,refertoourwebsite(http://security.panasonic.com/pss/security/support/info.html).

48

InstallationGuide(thisdocument)......................................................1setWarrantycard....................................................................................1setCD-ROM*1........................................................................................1pc.Codelabel*2......................................................................................1pc.

Thefollowingpartsareusedduringinstallationprocedures.4Palarmcable..................................................................................1pc.2Ppowercable.................................................................................1pc.Waterprooftape.................................................................................1pc.Adapterbox......................................................................................1pc.Cameramountbracket......................................................................1pc.Mountbracketcover.........................................................................2pcs.Adapterboxmountingscrew(M4x35mm)......................................1pc.Mountingscrewsforadapterbox/cameramountbracket(M5x20mm)..........................................................................................................5pcs.(ofthem,1forspare)Camerafixingscrew(M4x10mm)....................................................4pcs.(ofthem,1forspare)Mountbracketcoverscrew(M3x6mm)...........................................3pcs.(ofthem,1forspare)LANcablecover................................................................................1pc.

*1 TheCD-ROMcontainstheoperatinginstructionsanddifferentkindsoftoolsoftwareprograms. *2 Thislabelmayberequiredfornetworkmanagement.Thenetworkadministratorshallretainthe

codelabel.

Standard accessories

UserLicenseAccessory(ForH.264)............................BB-HCA8ABB-HCA8CE

Optional accessories

Information for Users on Collection and Disposal of Old Equipment and used Batteries

These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste.For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC and 2006/66/EC.By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling.For more information about collection and recycling of old products and batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items.Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.

For business users in the European UnionIf you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

[Information on Disposal in other Countries outside the European Union]These symbols are only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal.

Note for the battery symbol (bottom two symbol examples):This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement set by the Directive for the chemical involved.

Cd

For U.S. and Canada:

Panasonic System Communications Company of North America,Unit of Panasonic Corporation of North Americawww.panasonic.com/business/For customer support, call 1.800.528.6747Two Riverfront Plaza, Newark, NJ 07102-5490

Panasonic Canada Inc.5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada (905)624-5010www.panasonic.ca

©PanasonicSystemNetworksCo.,Ltd.2014

sL0914-4075PGQX1659WBPrintedinChina

For Europe and other countries:

Panasonic Corporationhttp://panasonic.net

Panasonic System Networks Co., Ltd. Fukuoka, Japan

Authorised Representative in EU:

Panasonic Testing CentrePanasonic Marketing Europe GmbHWinsbergring 15, 22525 Hamburg, Germany

Included Installation Instructions Network ... - Panasonic

Documents

Transcript of Included Installation Instructions Network ... - Panasonic