IMPORTANT SAFETY INSTRUCTIONInstall the recessed troffer only in 15/16” NEMA type G or type NFG...
5
READ CAREFULLY BEFORE INSTALLING FIXTURE. PLEASE KEEP THIS MANUAL FOR FUTURE USE. Risk of fire or electric shock. Make sure power supply is off before installing or maintaining the product. Risk of fire or electric shock. Install this product only in the luminaires that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the product does not exceed the input rating of the luminaire. Install the recessed troffer only in 15/16” NEMA type G or type NFG t-grids with a minimum troffer depth of 3”. Risk of fire or electric shock. To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects. Risk of fire or electric shock. Installation guide requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician. Risk of fire or electric shock. Only those open holes indicated in the photographs and/or drawings may be made or altered as a result of kit installation. Do not make or alter any open holes in an enclosure of wiring or electrical components during installation. Risk of fire or electric shock. Never perform maintenance or cleaning while fixture is energized. Disconnect power and allow fixture to cool before maintaining. Risk of injury. Wear safety glasses and gloves during installation and servicing. Fixtures must be wired in accordance with the national electrical code and all applicable local codes. Proper grounding is required for safety. This product must be installed in accordance with the application code by a person familiar with the construction and operation of the product and the hazards involved. Make certain power off before installing or maintaining fixture. Check that voltage is compatible with fixture driver, use approved connectors for all electrical connections. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult a licensed electrician for help IMPORTANT SAFETY INSTRUCTION 1. Review the diagrams before beginning and make sure the fixture is grounded properly. 2. For lighting controls, use driver wiring diagram. 3. Turn power off and wait for fixture to cool. 4. Maintenance must be done by qualified electricians. MAINTENANCE CAUTION WARNING Risk of Fire or Electric Shock NOTICE TR1 SERIES - INSTALLATION INSTRUCTIONS Flex Lighting Solutions
Transcript of IMPORTANT SAFETY INSTRUCTIONInstall the recessed troffer only in 15/16” NEMA type G or type NFG...
READ CAREFULLY BEFORE INSTALLING FIXTURE.PLEASE KEEP THIS MANUAL FOR FUTURE USE.
Risk of fire or electric shock. Make sure power supply is off before installing or maintaining the product.
Risk of fire or electric shock. Install this product only in the luminaires that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the product does not exceed the input rating of the luminaire.
Install the recessed troffer only in 15/16” NEMA type G or type NFG t-grids with a minimum troffer depth of 3”.
Risk of fire or electric shock. To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
Risk of fire or electric shock. Installation guide requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
Risk of fire or electric shock. Only those open holes indicated in the photographs and/or drawings may be made or altered as a result of kit installation. Do not make or alter any open holes in an enclosure of wiring or electrical components during installation.
Risk of fire or electric shock. Never perform maintenance or cleaning while fixture is energized. Disconnect power and allow fixture to cool before maintaining.
Risk of injury. Wear safety glasses and gloves during installation and servicing.
Fixtures must be wired in accordance with the national electrical code and all applicable local codes.Proper grounding is required for safety.
This product must be installed in accordance with the application code by a person familiar with the construction and operation of the product and the hazards involved. Make certain power off before installing or maintaining fixture.
Check that voltage is compatible with fixture driver, use approved connectors for all electrical connections.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna Increase the separation between the equipment and
the receiver Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected Consult a licensed electrician for help
IMPORTANT SAFETY INSTRUCTION
1. Review the diagrams before beginning and make sure the fixture is grounded properly.
2. For lighting controls, use driver wiring diagram.3. Turn power off and wait for fixture to cool.4. Maintenance must be done by qualified electricians.
MAINTENANCE CAUTION
WARNINGRisk of Fire or Electric Shock NOTICE
TR1 SERIES - INSTALLATION INSTRUCTIONS Flex Lighting Solutions
With power disconnected to your electrical box, remove the old fixture. If the old fixture is attached to an electrical box that has more than two wire leads, use tape and markings to keep track of which wires were attached to each other.
To remove the COVER/REFLECTOR First: Using a Philips screwdriver and remove the screw(s). Setthem out of the way so they will not get lost
Make sure all power is turned off before installing fixture intothe plenum.
Place assembled fixture on a secure surface.
Remove the LENS/DIFFUSER by squeezing the sidesso that they disengage the tabs and set it out of theway so that it will not get damaged.
Second: Slide the COVER/REFLECTOR inward to disengage all the tabs. Once the tabs have all cleared remove the COVER/REFLECTOR and set it out of the way so that it will not get damaged.
STEP BY STEP INSTALLATION
1
2
4
3
5
IMPORTANT SAFETY INSTRUCTION
Page 2Continued on next page
TR1 SERIES - INSTALLATION INSTRUCTIONS Flex Lighting Solutions
While standing on a secure surface lift the Fixture(BODY/REFLECTOR with the END PLATES attached) up and insert one end into the “T” grid opening. Rotate the fixture so that the fixture can clear the sides of the opening in the “T” grid.
6
Rotate the Fixture so that the ends and sides line up with the “T” grid. Lower the fixture until it is resting securely on the “T” grid.
8
Feed the black, white and green leads from the main power supply through the access plate in the BODY/REFLECTOR and connect them to the corresponding wires from the driver and the ground lead attached to the BODY/REFLECTOR using UL approved wire connectors.
11
Continue to raise and rotate the Fixture into the plenum until it has completely cleared the “T” grid.
7
Remove the access plate, connect and secure the conduit pipe to the access plate through the K/O.
Feed the mains power supply through the conduit pipe and into the fixture.
9
Now that the fixture is seated securely in the “T” grid make sure the power is still turned off before connecting power leads.
10
IMPORTANT SAFETY INSTRUCTION
Page 3Continued on next page
TR1 SERIES - INSTALLATION INSTRUCTIONS Flex Lighting SolutionsTR1 SERIES - INSTALLATION INSTRUCTIONS Flex Lighting Solutions
Slide COVER/REFLECTOR outward while making sure the tabs in the BODY/REFLECTOR are engaging the slots in the small flange of the COVER/REFLECTOR.
Replace the LENS/DIFFUSER by squeezing it so that it can fit between the two tabs of the BODY/REFLECTOR and the two tabs of the COVER/REFLECTOR.
Secure the COVER/REFLECTOR to the BODY/REFLECTOR with screw(s).
14 15
To replace the COVER/REFLECTOR insert the side flange above the “T” grid and engage the tabs at each end with the slots in both END PLATES rotate the COVER/REFLECTOR upward into the plenum.
12
Turn power back on.
17
Release the pressure on the lens/diffuser so that they engage all the tabs.
16
IMPORTANT SAFETY INSTRUCTION
13
Page 4Continued on next page
TR1 SERIES - INSTALLATION INSTRUCTIONS Flex Lighting Solutions
CARE AND CLEANINGYou may want to periodically clean the fixture using a mild, non-abrasive glass cleaner and soft cloth. Do NOT use solvents or cleaners containing abrasive agents. When cleaning the fixture, make sure you have the power turned off and do not open the diffuser.
TROUBLESHOOTINGMinor problems often can be fixed without the help of an electrician. Before doing any work on the fixture, shut off power supply at the circuit breaker panel to avoid electrical shock.
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTIONFixture doesn’t light 1. Power is off
2. Bad wire connection 3. Defective wall switch
1. Check circuit breaker or wall switch 2. Check wire splices 3. Replace switch
Circuit breaker trips when light is turned on
1. Crossed wires or power 1. Check wiring connections.
IMPORTANT SAFETY INSTRUCTION
Page 5
TR1 SERIES - INSTALLATION INSTRUCTIONS Flex Lighting Solutions
www.flexlightingsolutions.com
888.799.5002 option 3
