IF Alignment Using a Wobbulator - Canadian Vintage Radio Society · 2017. 4. 25. · ’Radio...
Transcript of IF Alignment Using a Wobbulator - Canadian Vintage Radio Society · 2017. 4. 25. · ’Radio...
![Page 1: IF Alignment Using a Wobbulator - Canadian Vintage Radio Society · 2017. 4. 25. · ’Radio Bygones’ magazine, April/May, 2003. It is combined in one box with a ... of same radio](https://reader036.fdocuments.net/reader036/viewer/2022062403/5fe8f61b8ba5d7789c58ee27/html5/thumbnails/1.jpg)
IF AlignmentUsing a Wobbulator
By Gerry O’Hara, VE7GUH
![Page 2: IF Alignment Using a Wobbulator - Canadian Vintage Radio Society · 2017. 4. 25. · ’Radio Bygones’ magazine, April/May, 2003. It is combined in one box with a ... of same radio](https://reader036.fdocuments.net/reader036/viewer/2022062403/5fe8f61b8ba5d7789c58ee27/html5/thumbnails/2.jpg)
Objectives• Optimize (not necessarily maximize) IF
gain• Produce desired IF response curve(s)
– Width of ‘nose’– Steepness of ‘skirts’– Symmetry
• Analyze for spurious responses
![Page 3: IF Alignment Using a Wobbulator - Canadian Vintage Radio Society · 2017. 4. 25. · ’Radio Bygones’ magazine, April/May, 2003. It is combined in one box with a ... of same radio](https://reader036.fdocuments.net/reader036/viewer/2022062403/5fe8f61b8ba5d7789c58ee27/html5/thumbnails/3.jpg)
Response curves• What is an IF response curve?• What should it look like?
– Depends on what your using it for…
![Page 4: IF Alignment Using a Wobbulator - Canadian Vintage Radio Society · 2017. 4. 25. · ’Radio Bygones’ magazine, April/May, 2003. It is combined in one box with a ... of same radio](https://reader036.fdocuments.net/reader036/viewer/2022062403/5fe8f61b8ba5d7789c58ee27/html5/thumbnails/4.jpg)
Alignment Techniques• Use a received signal and tune ‘by ear’• Use a signal genny and ‘tune by ear’• Use a signal genny and an output
meter• Use a ‘Wobbulator’ and ‘scope• Use a Wobbulator, scope and accurate
frequency source (eg. crystal oscillator or frequency synthesizer)
![Page 5: IF Alignment Using a Wobbulator - Canadian Vintage Radio Society · 2017. 4. 25. · ’Radio Bygones’ magazine, April/May, 2003. It is combined in one box with a ... of same radio](https://reader036.fdocuments.net/reader036/viewer/2022062403/5fe8f61b8ba5d7789c58ee27/html5/thumbnails/5.jpg)
What is a ‘Wobbulator’?• A signal genny that can be made to
‘sweep’ its frequency across the IF bandwidth of the receiver being aligned
• The swept output is applied to the IF amplifier input
• The (rectified) output voltage of the IF amplifier is viewed on a ‘scope
• The output voltage will vary depending on the alignment of the IF tuned circuits
Not a wobbulator
![Page 6: IF Alignment Using a Wobbulator - Canadian Vintage Radio Society · 2017. 4. 25. · ’Radio Bygones’ magazine, April/May, 2003. It is combined in one box with a ... of same radio](https://reader036.fdocuments.net/reader036/viewer/2022062403/5fe8f61b8ba5d7789c58ee27/html5/thumbnails/6.jpg)
What is a ‘Wobbulator’?• The oscillator in the signal genny is
made to be voltage controlled (‘VCO’)• The VCO is controlled by the timebase
of the ‘scope – this is a sawtoothwaveform
Voltage
Time
![Page 7: IF Alignment Using a Wobbulator - Canadian Vintage Radio Society · 2017. 4. 25. · ’Radio Bygones’ magazine, April/May, 2003. It is combined in one box with a ... of same radio](https://reader036.fdocuments.net/reader036/viewer/2022062403/5fe8f61b8ba5d7789c58ee27/html5/thumbnails/7.jpg)
What is a ‘Wobbulator’?• Ok, so this circuit is solid-state (argh!),
so just imagine these are triodes…
![Page 8: IF Alignment Using a Wobbulator - Canadian Vintage Radio Society · 2017. 4. 25. · ’Radio Bygones’ magazine, April/May, 2003. It is combined in one box with a ... of same radio](https://reader036.fdocuments.net/reader036/viewer/2022062403/5fe8f61b8ba5d7789c58ee27/html5/thumbnails/8.jpg)
Homebrew Wobbulator• Very few commercial units available…
so, why not build one yourself?
The wobbulator circuit board is on the lower right, frequency counter board upper left
The example here is from ’Radio Bygones’ magazine, April/May, 2003. It is combined in one box with a DFM kit from Norcal
![Page 9: IF Alignment Using a Wobbulator - Canadian Vintage Radio Society · 2017. 4. 25. · ’Radio Bygones’ magazine, April/May, 2003. It is combined in one box with a ... of same radio](https://reader036.fdocuments.net/reader036/viewer/2022062403/5fe8f61b8ba5d7789c58ee27/html5/thumbnails/9.jpg)
So what can it do?The controls:
![Page 10: IF Alignment Using a Wobbulator - Canadian Vintage Radio Society · 2017. 4. 25. · ’Radio Bygones’ magazine, April/May, 2003. It is combined in one box with a ... of same radio](https://reader036.fdocuments.net/reader036/viewer/2022062403/5fe8f61b8ba5d7789c58ee27/html5/thumbnails/10.jpg)
In use…• For automatic sync, your ‘scope must
be able to output a suitable ramp output signal (‘sweep signal’)
• If it does not have this (the Hitachi example here did not), then tap into the ‘scope’s timebase circuit
• The ramp signal controls the sweep width of the wobbulator’s VCO (+/-from the pre-set centre frequency)
![Page 11: IF Alignment Using a Wobbulator - Canadian Vintage Radio Society · 2017. 4. 25. · ’Radio Bygones’ magazine, April/May, 2003. It is combined in one box with a ... of same radio](https://reader036.fdocuments.net/reader036/viewer/2022062403/5fe8f61b8ba5d7789c58ee27/html5/thumbnails/11.jpg)
In use• Connect the wobbulator, receiver and
‘scope as shown in slide 6
• Set the wobbulator centre frequency to the desired nominal IF frequency
• Set the ‘scope to sweep at a slow rate
Sweep outY-in
IF-in
Sweep in
IF-out
![Page 12: IF Alignment Using a Wobbulator - Canadian Vintage Radio Society · 2017. 4. 25. · ’Radio Bygones’ magazine, April/May, 2003. It is combined in one box with a ... of same radio](https://reader036.fdocuments.net/reader036/viewer/2022062403/5fe8f61b8ba5d7789c58ee27/html5/thumbnails/12.jpg)
In use• Set wobbulator sweep width to be
slightly wider than the IF bandwidth• Observe ‘scope trace and commence
adjustment of IF transformer cores• Start with the one nearest the detector
first, working back towards the mixer stage 12a/b3a/b Detector AF Stages
BFO
From Mixer Stage
1st IF 2nd IF
![Page 13: IF Alignment Using a Wobbulator - Canadian Vintage Radio Society · 2017. 4. 25. · ’Radio Bygones’ magazine, April/May, 2003. It is combined in one box with a ... of same radio](https://reader036.fdocuments.net/reader036/viewer/2022062403/5fe8f61b8ba5d7789c58ee27/html5/thumbnails/13.jpg)
In use• Outer peak is usually the correct one• Many IF trxfrs have two adjustments• Use the right tool(s)!!• Be careful not to break the core (‘slug’)• Remove any old elastic filament, wax
etc, replace with small dab of Rocolhigh-viscosity grease
![Page 14: IF Alignment Using a Wobbulator - Canadian Vintage Radio Society · 2017. 4. 25. · ’Radio Bygones’ magazine, April/May, 2003. It is combined in one box with a ... of same radio](https://reader036.fdocuments.net/reader036/viewer/2022062403/5fe8f61b8ba5d7789c58ee27/html5/thumbnails/14.jpg)
In useLeft: ‘Scope trace of IF response of radio before alignment (nominal IF is 465kHz)
Right: ‘Scope trace of same radio after alignment
465kHz455kHz 475kHz445kHz 485kHz
![Page 15: IF Alignment Using a Wobbulator - Canadian Vintage Radio Society · 2017. 4. 25. · ’Radio Bygones’ magazine, April/May, 2003. It is combined in one box with a ... of same radio](https://reader036.fdocuments.net/reader036/viewer/2022062403/5fe8f61b8ba5d7789c58ee27/html5/thumbnails/15.jpg)
In useLeft: Using a second signal genny or crystal oscillator to pinpoint a frequency along the trace – here exactly at the 465kHz centre frequency. This produces a beat frequency with the wobbulator signal
Right: As above, but with the second signal genny/crystal oscillator set to 460kHz (zero beat to left of the curve)
![Page 16: IF Alignment Using a Wobbulator - Canadian Vintage Radio Society · 2017. 4. 25. · ’Radio Bygones’ magazine, April/May, 2003. It is combined in one box with a ... of same radio](https://reader036.fdocuments.net/reader036/viewer/2022062403/5fe8f61b8ba5d7789c58ee27/html5/thumbnails/16.jpg)
In use
Left: Flattening of trace caused by too high an injection level resulting in receiver overload
Right: Trace resulting from IF strip that includes a 4kHz mechanical filter. Receiver aligned for maximum sensitivity
![Page 17: IF Alignment Using a Wobbulator - Canadian Vintage Radio Society · 2017. 4. 25. · ’Radio Bygones’ magazine, April/May, 2003. It is combined in one box with a ... of same radio](https://reader036.fdocuments.net/reader036/viewer/2022062403/5fe8f61b8ba5d7789c58ee27/html5/thumbnails/17.jpg)
In use
Left: Trace resulting from IF strip that includes a 2.6kHz ceramic filter. Receiver aligned for maximum sensitivity
• A flat ‘nose’ and steep ‘skirts’ are ideal response characteristics
• Wider ‘nose’ giver better fidelity response (+/-8kHz) for AM reception
![Page 18: IF Alignment Using a Wobbulator - Canadian Vintage Radio Society · 2017. 4. 25. · ’Radio Bygones’ magazine, April/May, 2003. It is combined in one box with a ... of same radio](https://reader036.fdocuments.net/reader036/viewer/2022062403/5fe8f61b8ba5d7789c58ee27/html5/thumbnails/18.jpg)
In use• Tailoring the IF response curve:
• May be obtained by ‘staggering’ tuning of several IF transformers, or
• Adjusting coupling within transformers (closer spacing gives wider curve) – used in Super Pro and some Eddystones
• Narrower ‘nose’ better for SSB and CW reception
• Steeper skirts to optimize selectivity (reject adjacent signals)
![Page 19: IF Alignment Using a Wobbulator - Canadian Vintage Radio Society · 2017. 4. 25. · ’Radio Bygones’ magazine, April/May, 2003. It is combined in one box with a ... of same radio](https://reader036.fdocuments.net/reader036/viewer/2022062403/5fe8f61b8ba5d7789c58ee27/html5/thumbnails/19.jpg)
Questions?
By Gerry O’Hara, VE7GUH