Ideal Turbojet Parametric Cycle Analysis - Amazon Simple … · 2015-12-18 · Ideal Turbojet...

13
Ideal Turbojet Parametric Cycle Analysis © 2015 SIM University. All rights reserved. The steps of parametric cycle analysis to an ideal turbojet The output of parametric cycle analysis of an ideal turbojet The differences in performance between ideal simple turbojet and one with afterburning © 2015 SIM University. All rights reserved. Introduction

Transcript of Ideal Turbojet Parametric Cycle Analysis - Amazon Simple … · 2015-12-18 · Ideal Turbojet...

Page 1: Ideal Turbojet Parametric Cycle Analysis - Amazon Simple … · 2015-12-18 · Ideal Turbojet –With and Without Afterburning • Performing parametric cycle analysis to an ideal

Ideal Turbojet

Parametric Cycle Analysis

© 2015 SIM University. All rights reserved.

• The steps of parametric cycle analysis to an ideal

turbojet

• The output of parametric cycle analysis of an ideal

turbojet

• The differences in performance between ideal

simple turbojet and one with afterburning

© 2015 SIM University. All rights reserved.

Introduction

Page 2: Ideal Turbojet Parametric Cycle Analysis - Amazon Simple … · 2015-12-18 · Ideal Turbojet –With and Without Afterburning • Performing parametric cycle analysis to an ideal

• Provides thrust even at V0=0 (vs ramjet)

• Turbine extracts only the power required to drive the compressor

and accessories necessary for continuous operation

© 2015 SIM University. All rights reserved.

Adapted: “Elements of Propulsion: Gas Turbines and Rockets” by Jack D. Mattingly

Ideal Turbojet

Figure 4-7 T-s Diagram and H-K Diagram of an Ideal Turbojet

© 2015 SIM University. All rights reserved. Adapted: “Elements of Propulsion: Gas Turbines and Rockets” by Jack D. Mattingly

Ideal Turbojet

Page 3: Ideal Turbojet Parametric Cycle Analysis - Amazon Simple … · 2015-12-18 · Ideal Turbojet –With and Without Afterburning • Performing parametric cycle analysis to an ideal

• Input

• Output

- new term (vs ideal ramjet)

© 2015 SIM University. All rights reserved. Adapted: “Elements of Propulsion: Gas Turbines and Rockets” by Jack D. Mattingly

Ideal Turbojet

• Equations

© 2015 SIM University. All rights reserved. Adapted: “Elements of Propulsion: Gas Turbines and Rockets” by Jack D. Mattingly

Ideal Turbojet

Page 4: Ideal Turbojet Parametric Cycle Analysis - Amazon Simple … · 2015-12-18 · Ideal Turbojet –With and Without Afterburning • Performing parametric cycle analysis to an ideal

• Equations

© 2015 SIM University. All rights reserved. Adapted: “Elements of Propulsion: Gas Turbines and Rockets” by Jack D. Mattingly

Ideal Turbojet

© 2015 SIM University. All rights reserved.

T0 = 220 K; γ = 1.4; cP=1.004 kJ/(kg K); hPR = 42,800 kJ/kg; Tt4 = 1700K

Variation of Specific Thrust and TSFC against Mach Number

Source: Soon Kim Tat

Turbojet – Mach Number Variation

Page 5: Ideal Turbojet Parametric Cycle Analysis - Amazon Simple … · 2015-12-18 · Ideal Turbojet –With and Without Afterburning • Performing parametric cycle analysis to an ideal

© 2015 SIM University. All rights reserved.

T0 = 220 K; γ = 1.4; cP=1.004 kJ/(kg K); hPR = 42,800 kJ/kg; Tt4 = 1700K

Variation of Efficiency against Mach Number

Source: Soon Kim Tat

Turbojet – Mach Number Variation

© 2015 SIM University. All rights reserved.

T0 = 220 K; γ = 1.4; cP=1.004 kJ/(kg K); hPR = 42,800 kJ/kg; πc = 10

Effect of Turbine Inlet Temperature Variation

Source: Soon Kim Tat

Turbojet – Effect of Turbine Inlet Temperature

Page 6: Ideal Turbojet Parametric Cycle Analysis - Amazon Simple … · 2015-12-18 · Ideal Turbojet –With and Without Afterburning • Performing parametric cycle analysis to an ideal

Variation of Specific Thrust against Compressor Pressure Ratio

Lower

compressor

pressure ratio is

desired at higher

Mach numbers

© 2015 SIM University. All rights reserved.

T0 = 220 K; γ = 1.4; cP=1.004 kJ/(kg K); hPR = 42,800 kJ/kg; Tt4 = 1700K

Source: Soon Kim Tat

Turbojet – Compressor Pressure Ratio Variation

Variation of TSFC against Compressor Pressure Ratio

© 2015 SIM University. All rights reserved.

T0 = 220 K; γ = 1.4; cP=1.004 kJ/(kg K); hPR = 42,800 kJ/kg; Tt4 = 1700K

Source: Soon Kim Tat

Turbojet – Compressor Pressure Ratio Variation

Page 7: Ideal Turbojet Parametric Cycle Analysis - Amazon Simple … · 2015-12-18 · Ideal Turbojet –With and Without Afterburning • Performing parametric cycle analysis to an ideal

• Optimum Compressor (for max F/ṁo) Temperature and Pressure Ratio

• Lower compressor pressure ratio is desired for higher Mach number

operation

© 2015 SIM University. All rights reserved. Adapted: “Elements of Propulsion: Gas Turbines and Rockets” by Jack D. Mattingly

Optimum Compressor Pressure Ratio

• Thrust of turbojet being increased by afterburner (after the turbine)

© 2015 SIM University. All rights reserved. Adapted: “Elements of Propulsion: Gas Turbines and Rockets” by Jack D. Mattingly

Ideal Afterburning Turbojet

Page 8: Ideal Turbojet Parametric Cycle Analysis - Amazon Simple … · 2015-12-18 · Ideal Turbojet –With and Without Afterburning • Performing parametric cycle analysis to an ideal

Figure 4-10 T-s and H-K Diagram of an Ideal Afterburning Turbojet

© 2015 SIM University. All rights reserved. Adapted: “Elements of Propulsion: Gas Turbines and Rockets” by Jack D. Mattingly

Ideal Afterburning Turbojet

• Input

• Outputc

- new term (vs ideal turbojet)

© 2015 SIM University. All rights reserved. Adapted: “Elements of Propulsion: Gas Turbines and Rockets” by Jack D. Mattingly

Ideal Afterburning Turbojet

Page 9: Ideal Turbojet Parametric Cycle Analysis - Amazon Simple … · 2015-12-18 · Ideal Turbojet –With and Without Afterburning • Performing parametric cycle analysis to an ideal

• Equations

© 2015 SIM University. All rights reserved. Adapted: “Elements of Propulsion: Gas Turbines and Rockets” by Jack D. Mattingly

Ideal Afterburning Turbojet

• Equations

© 2015 SIM University. All rights reserved. Adapted: “Elements of Propulsion: Gas Turbines and Rockets” by Jack D. Mattingly

Ideal Afterburning Turbojet

Page 10: Ideal Turbojet Parametric Cycle Analysis - Amazon Simple … · 2015-12-18 · Ideal Turbojet –With and Without Afterburning • Performing parametric cycle analysis to an ideal

• Optimum (max F/ṁo) Compressor Temperature Ratio

© 2015 SIM University. All rights reserved. Adapted: “Elements of Propulsion: Gas Turbines and Rockets” by Jack D. Mattingly

Ideal Afterburning Turbojet

© 2015 SIM University. All rights reserved.

T0 = 220 K; γ = 1.4; cP=1.004 kJ/(kg K); hPR = 42,800 kJ/kg; Tt4 = 1700K ; Tt4 = 2300K

Variation of Specific Thrust against Compressor Pressure Ratio

Source: Soon Kim Tat

Ideal Afterburning Turbojet

Page 11: Ideal Turbojet Parametric Cycle Analysis - Amazon Simple … · 2015-12-18 · Ideal Turbojet –With and Without Afterburning • Performing parametric cycle analysis to an ideal

© 2015 SIM University. All rights reserved.

T0 = 220 K; γ = 1.4; cP=1.004 kJ/(kg K); hPR = 42,800 kJ/kg; Tt4 = 1700K ; Tt4 = 2300K

Variation of TSFC against Compressor Pressure Ratio

Source: Soon Kim Tat

Ideal Afterburning Turbojet

• Afterburning causes increase in:

– Specific thrust F/ṁ0

– Thrust specific fuel consumption S

• Optimum compressor pressure ratio (maximum F/ṁ0 ):

– Reduces as Mach number increases

– For afterburning turbojet is higher than non-afterburning

→Afterburning turbojet with moderate to high πc still offers high F/ṁ0 at

high flight Mach numbers

• Fuel/air ratio

– In main burner (f )is unchanged

– In afterburner (fAB ) increases with M and πc

– Total (ftot ) decreases with M and is not a function of πc

• Thermal, propulsive, and overall efficiencies are reduced by afterburning

© 2015 SIM University. All rights reserved. Adapted: “Elements of Propulsion: Gas Turbines and Rockets” by Jack D. Mattingly

Comparison of Afterburning

Page 12: Ideal Turbojet Parametric Cycle Analysis - Amazon Simple … · 2015-12-18 · Ideal Turbojet –With and Without Afterburning • Performing parametric cycle analysis to an ideal

Engine with =30 operates

optimally at M0=2 with AB, and

near optimum at subsonic speeds

where less thrust is required and

S is lower

Optimum Ideal Turbojet

Compressor Pressure

Ratio

Optimum Ideal Turbojet

Performance

© 2015 SIM University. All rights reserved. Adapted: “Elements of Propulsion: Gas Turbines and Rockets” by Jack D. Mattingly

Ideal Turbojet – With and Without Afterburning

• Performing parametric cycle analysis to an ideal

turbojet engines, including with afterburner

• Study of the output of parametric cycle analysis of

an ideal simple turbojet and compare its

performance against one with afterburner.

• Evaluating the optimum compressor pressure

ratio in a turbojet engine.

© 2015 SIM University. All rights reserved.

Summary

Page 13: Ideal Turbojet Parametric Cycle Analysis - Amazon Simple … · 2015-12-18 · Ideal Turbojet –With and Without Afterburning • Performing parametric cycle analysis to an ideal

• Given an ideal turbojet is operating at the following

conditions:

T0 = 220 K; γ = 1.4; cP=1.004 kJ/(kg K);

hPR = 42,800 kJ/kg; Tt4 = 1700K

• Compute the optimum compressor pressure ratio

when operating at Mach 1.0. You may use the

following expressions

• Determine the maximum specific thrust of this engine

• You may compare the results with the charts given in

this presentation

© 2015 SIM University. All rights reserved.

Reflection Question