Hypac C766C, C778B - om.pdf
-
Upload
namduong368 -
Category
Documents
-
view
247 -
download
1
Transcript of Hypac C766C, C778B - om.pdf
-
8/10/2019 Hypac C766C, C778B - om.pdf
1/122
CALIFORNIA
Proposition 65 Warning
WARNING:Diesel engine exhaust and
some of its constituents are known to thestate of California to cause cancer, birthdefects, and other reproductiveharm.
CALIFORNIA
Proposition 65 Warning
WARNING:Battery posts, terminals andrelated accessories contain lead andlead compounds, chemicals known to thestate of California to cause cancer, birthdefects, and other reproductiveharm.Wash hands after handling.
-
8/10/2019 Hypac C766C, C778B - om.pdf
2/122
-
8/10/2019 Hypac C766C, C778B - om.pdf
3/122
Revision R4Form 0852656
8/03
OPERATINGMANUAL
C778B
C766C
-
8/10/2019 Hypac C766C, C778B - om.pdf
4/122
-
8/10/2019 Hypac C766C, C778B - om.pdf
5/122
DANGER:Do Not operate machine with the Roll Over/ Falling Object Protection Structure (ROPS/FOPS) and Operator Restraints (Seat Belt Sets) NOT properly installed.
DANGER: If the machine was received with the Roll Over/Falling Object ProtectionStructure (ROPS/FOPS) and Operator Restraints (Seat Belt Sets) NOTinstalled, they MUST be installed BEFORE the machine is operated, usingthe installation instructions drawing, included with the installation kit,
and/or the illustration below.In the event of a machine roll over, serious injury, or death, can occur dueto failure to correctly install the Roll Over/Falling Object ProtectionStructure (ROPS/FOPS) and Operator Restraints (Seat Belt Sets).
C766C & C778B
April 2000
Structure
Hexbolt - M20x110 - 10.9(4 used on far side).Tighten to a Torque of375 ft. lbs. (509 N.m).
M20 Washers
(4 used on far side)
Seat BeltSet (2 used)
Eyebolt
Washer
Lock Washer
Nut
Install each Seat Belt.Close Attaching Mechanisms Around Eyebolts.Install Cotter Pins and Bend.
Install Eybolts (2).One on each Side of the Seat.Tighten Nuts to a Torque of35 ft. lbs. (47 N.m).
Hexbolt - M20x65 - 10.9 (4 used on near side).Tighten to a Torque of 375 ft. lbs. (509N.m).
M20 Washers(4 used on near side)
-
8/10/2019 Hypac C766C, C778B - om.pdf
6/122
-
8/10/2019 Hypac C766C, C778B - om.pdf
7/122
CAUTION: Minor personal injury can result or a part, an assembly, or the engine
can be damaged if the CAUTION instructions are not followed.
DANGER: Serious personal injury, death and/or extensive property damage can result if the DANGER instructions are not followed.
WARNING: Serious personal injury and/or extensive property damage can
result if the WARNING instructions are not followed.
NOTE: Gives additional, and/or clarification details, which are to be used in
conjunction with previously presented information.
SYMBOLS USED IN THIS MANUAL
The following symbols have been used in THIS Manual to help communicate the intent of instructions. When one of the symbols appears, it conveys the meaning defined below:
CALIFORNIA
Proposition 65 Warning
WARNING:Diesel engine exhaust andsome of its constituents are known to thestate of California to cause cancer, birthdefects, and other reproductiveharm.
CALIFORNIA
Proposition 65 Warning
WARNING:Battery posts, terminals andrelated accessories contain lead andlead compounds, chemicals known to thestate of California to cause cancer, birthdefects, and other reproductiveharm.Wash hands after handling.
-
8/10/2019 Hypac C766C, C778B - om.pdf
8/122
SERVICE AND REPAIR PRECAUTIONS
ALWAYS inspect all slings, chains, or cables when lifting components, be sure that they are properlytied, fastened and balanced before lifting. Be sure that the lifting device is capable of retaining theweight to be lifted.
NEVER attempt to lift heavy parts by hand when a lifting device should be used.
ALWAYS wear safety glasses when performing any maintenance or repair work on the machine.
NEVER attempt to remove or repair any component, on the machine, while the engine is running.
NEVER leave the machine and/or heavy parts in an unstable position during repair.
ALWAYS support the machine with sound blocking.
ALWAYS keep the machine and work area clear of lubricants and dirt.
ALWAYS use the correct tools for the repair procedures being done on the machine,
ALWAYS keep tools in a good and clean condition.
ALWAYS use approved parts, that are designed for the machine being repaired. This helpsto ensure maximum service life of the machine.
ALWAYS be sure that all necessary nuts, bolts, snap rings, and other fastening devices, areremoved before using force to remove components.
ALWAYS attach a sign in the machine operators area, stating DO NOT OPERATE when themachine is being repaired.
ALWAYS observe ALL WARNING AND CAUTION statements given in the Operating Manual andService Manual and found on the machine decals.
-
8/10/2019 Hypac C766C, C778B - om.pdf
9/122
2/98 i
MANUAL - TABLE OF CONTENTS
PAGE
SECTION 1 - INTRODUCTION ................................................................................................................1-1.
SECTION 2 - SPECIFICATIONS ............................................................................................................. 2-1.
SECTION 3 - OPERATION ...................................................................................................................... 3-1.
SECTION 4 - MAINTENANCE .................................................................................................................4-1.
-
8/10/2019 Hypac C766C, C778B - om.pdf
10/122
-
8/10/2019 Hypac C766C, C778B - om.pdf
11/122
5/01
Section 1INTRODUCTION
1 - 1
TABLE OF CONTENTS
PAGE
GENERAL INFORMATION ......................................................................................................................1-2.
SPECIFICATIONS ....................................................................................................................................1-2.
OPERATING INSTRUCTIONS .................................................................................................................1-2.
MAINTENANCE PROCEDURES .............................................................................................................1-2.
REPAIR PROCEDURES ..........................................................................................................................1-3.
NAME PLATE / SERIAL NUMBER PLATE .............................................................................................1-3.
SERIAL NUMBER ....................................................................................................................................1-4.
-
8/10/2019 Hypac C766C, C778B - om.pdf
12/122
Section 1INTRODUCTION
1 - 2 5/01
FIGURE 1-1. MODEL C766C - COMPACTOR.
WARNING: ONLY authorized personnel, whoare fully trained in the machineoperation procedures, can operatethe Model C766C and C778BCompactors. Follow ALL instruc-tions given in THIS manual, and
written on the Machine Operationand Warning decal, found on theflat plate on the right side of, andbelow, the control panel.
MAINTENANCE PROCEDURES.
The maintenance schedules and procedures are found in Section 4 - MAINTENANCE, of THIS manual.
CAUTION:Follow ALL the maintenance schedules and instructions given in THIS manual.
GENERAL INFORMATION.
THIS manual contains SPECIFICATION informationand OPERATION, MAINTENANCE and REPAIRprocedures for theModel C766C and C778BCompactors[See Figures 1-1 and 1-2].
SPECIFICATIONS.
See Section 2 - SPECIFICATIONS, of THISmanual, for specifications on major systems usedon the machine.
OPERATING INSTRUCTIONS.
READ, UNDERSTAND and FOLLOW ALL theoperating instructions given in the FRONT, and inSection 3 - OPERATION, of THIS manual.
C766C
-
8/10/2019 Hypac C766C, C778B - om.pdf
13/122
5/01
Section 1INTRODUCTION
1 - 3
FIGURE 1-2. MODEL C778B - COMPACTOR.
SERIAL NUMBER [See Figures 1-3 and 1-4].
The SERIAL NUMBER indicates the design series,manufacturing location, serial number and year ofmachine shipment (older machines) [see Table 1-1].The machine serial number is located ON the
nameplate [see figure 1-3]. The serial number isalso stamped on the flat surface of the hitch assem-bly at the left hand side of the machine [see figure1-4].
CAUTION:ALL numbers and letters, contained in the SERIAL NUMBER,
MUST be given when requesting service and/or part information.
The name plate/serial number plate is locatedBELOW, and to the left side of, the steering wheel.The plate MUST stay fastened to the machine atALL times. If the plate is missing, or damaged, itMUST be replaced IMMEDIATELY. Contact yournearest Distributor to obtain a replacement plate.
REPAIR PROCEDURES.
MAJOR machine component REPAIRPROCEDURES are found in the SYSTEMREPAIR PROCEDURE sections of "ServiceManual", pn. 0852657.
CAUTION:For CORRECT machine component repair procedures, USE the REPAIR procedures given in the above service manual, and/or other referenced written materials
ONLY.
NAME PLATE /SERIAL NUMBER PLATE [SeeFigure 1-3].
-
8/10/2019 Hypac C766C, C778B - om.pdf
14/122
Section 1INTRODUCTION
1 - 4 5/01
C209 C - or 109 1605 U (stamped on older or machines - only) B215
C766C KEWANEE MACHINE YEAR OF
or SERIAL NUMBER SHIPMENTC778B
TABLE 1-1. MACHINE SERIAL NUMBER DESIGNATIONS.
FIGURE 1-3. NAMEPLATE / SERIAL NUMBER PLATE LOCATION.
FIGURE 1-4. SERIAL NUMBER LOCATION - NEAR HITCH ASSEMBLY.
C778B
B215C1605U
21,758
23,508
B215C1605U
-
8/10/2019 Hypac C766C, C778B - om.pdf
15/122
8/03
Section 2SPECIFICATIONS
2 - 1
TABLE OF CONTENTS
PAGE
GENERAL INFORMATION ................................................................................................................ 2-2.
TABLE 2-1. FRAME, HITCH AND FALLING OBJECT/ROLL OVERPROTECTIVE STRUCTURE [FOPS/ROPS] SPECIFICATIONS .......................................... 2-2.
TABLE 2-2. ENGINE SPECIFICATIONS ........................................................................................... 2-3.
TABLE 2-3. ELECTRICAL SPECIFICATIONS .................................................................................. 2-5.
TABLE 2-4. TRANSMISSION SYSTEM SPECIFICATIONS ............................................................. 2-6.
TABLE 2-5. BRAKE SYSTEM SPECIFICATIONS ............................................................................ 2-8.
TABLE 2-6. STEERING SYSTEM SPECIFICATIONS ...................................................................... 2-8.
TABLE 2-7. DRUM, VIBRATION AND CLEANER BAR SPECIFICATIONS ................................................................................................................ 2-10.
TABLE 2-8. WATER SPRAY SYSTEM SPECIFICATIONS ............................................................ 2-13.
TABLE 2-9. CONTROL AND INDICATOR SPECIFICATIONS ....................................................... 2-14.
TABLE 2-10. OPTIONAL EQUIPMENT SPECIFICATIONS ........................................................... 2-15.
TABLE 2-11. DIMENSION SPECIFICATIONS ................................................................................ 2-16.
TABLE 2-12. PERFORMANCE SPECIFICATIONS ........................................................................ 2-18.
TABLE 2-13. MACHINE SYSTEM CAPACITY SPECIFICATIONS ................................................ 2-18.
TABLE 2-14. COMPONENT WEIGHTS .......................................................................................... 2-19.
TABLE 2-15. TORQUE SPECIFICATIONS FOR STANDARD INCH
FASTENERS ........................................................................................................................ 2-21.
TABLE 2-16. TORQUE SPECIFICATIONS FOR STANDARD METRIC FASTENERS ........................................................................................................................ 2-22.
TABLE 2-17. LUBRICATION OILS, HYDRAULIC OILS AND COOLANT SPECIFICATIONS ............................................................................................................... 2-23.
TABLE 2-18. ADHESIVE THREAD LOCKING SPECIFICATIONS ................................................ 2-23.
-
8/10/2019 Hypac C766C, C778B - om.pdf
16/122
Section 2SPECIFICATIONS
2 - 2 8/03
TABLE 2-1. FRAME, HITCH AND FALLING OBJECT/ROLL OVER [FOPS/ROPS]PROTECTIVE STRUCTURE SPECIFICATIONS.
ITEM DESIGN DATA
FRAME and HITCH
Material Plate steel
Construction Unitized, all welded 2 section, with bolt-on front and rear weight plates
HITCH
Oscillation +/- 12 - side to side, 24 total
Articulation +/- 35 - right to left [Steering] turn, 70 total
FALLING OBJECT/ROLLOVER PROTECTIVESTRUCTURE [FOPS/ROPS]WITH OPERATORRESTRAINT SYSTEM
Type and Description Welded steel structure, bolted to machine for protective system and two [2] seat belt sets for operator restraint, conforms to SAE recommended practice J-1040C, J-231 and J-386; and CSA B352 [Canada]
Machine dimensions, weights, performance andtorque specifications are also given in THISsection.
GENERAL INFORMATION.
THIS section gives specification tables for eachMAJOR machine system of the Model C766C andC778B Compactors.
-
8/10/2019 Hypac C766C, C778B - om.pdf
17/122
8/03
Section 2SPECIFICATIONS
2 - 3
TABLE 2-2. ENGINE SPECIFICATIONS.
ITEM DESIGN DATA
ENGINE
Model and 4B3.9 QSB-C130 Cummins Diesel, with automatic, ether, cold start aidManufacturer
Type 4 Cycle diesel, Turbocharged and charge air cooled
Number of 4Cylinders
Displacement 239 in.3 [3.92 l]
Bore & Stroke 4.02 in. [102 mm] x 4.72 in. [120 mm]
Rated Brake 130 hp @ 2500 rpm [97 Kw at 2500 rpm]
Horsepower
Compression Ratio 18:1
Firing Order 1-3-4-2
Low Idle Speed 900 -1000 rpm
High Idle Speed 2500 +/-10 rpm, NO load
Engine Oil Type See Cummins "Operation and Maintenance Manual - B seriesEngine" - for correct oil type
Turbocharger
Type Holsett
Boost Pressure 18.7 psi [1.3 bar] @ 1750 rpm
ENGINE COOLING SYSTEM
Radiator Type Full flow, liquid pressure, W/O integral oil cooler
System Coolant Capacity 19 qts. [17.97 l]
Thermostat Range 180-190 F [82-88 C], thermostat opens
-
8/10/2019 Hypac C766C, C778B - om.pdf
18/122
Section 2SPECIFICATIONS
2 - 4 8/03
ITEM DESIGN DATA
ENGINE FUEL
Type Used Use ONLY distillate fuels [A.S.T.M. No.1 or No.2 fuel oil or No.1Dor No. 2D diesel fuel are EXAMPLES]. The fuel MUST have aMINIMUM cetane number of 35. Heavier oil is generally preferablebecause of its higher energy content
Fuel Capacity 50 Gallons [189 L] - C766C or 60 Gallons [227 L] - C778B
Rate of Fuel 4.1 Gallons per hourConsumption [at [15.5 liters per hour]*normal engine H.P.at 40% load]
*Operating conditions, that vary, can cause different fuelconsumption amounts than those given
FUEL FILTERS
Fuel Strainer Suction line, replaceable spin-on element - with water drain [SeeEngine Manual]
Fuel Filter Pressure line, replaceable spin-on element [See Engine Manual]
FUEL PUMP
Type Bosch, in line type
FUEL INJECTORS
Quantity and Type 4, close nozzle
-
8/10/2019 Hypac C766C, C778B - om.pdf
19/122
8/03
Section 2SPECIFICATIONS
2 - 5
TABLE 2-3. ELECTRICAL SPECIFICATIONS.
ITEM DESIGN DATA
BATTERY
Number Per Machine One [1], maintenance free
Ampere Hour Rating 900 CCA
Voltage 12 Volts
ALTERNATOR
Voltage 12 Volt, negative ground
Output Amperage 105 Amps
Maximum Charge 105 Amps - 14 volts [cold]Rate
Direction of Clockwise [C.W.] - viewed fromRotation drive end
Fan Belt Tension Automatic belt tension mechanism keeps serpentine beltand Method Used to under tension at ALL timesAchieve
STARTER
Manufacturer Delco Remy [see ENGINE starter plate, for starter part number]
Voltage and Type 12 Volt, negative ground
-
8/10/2019 Hypac C766C, C778B - om.pdf
20/122
Section 2SPECIFICATIONS
2 - 6 8/03
TRANSMISSION SYSTEM
System Type Hydrostatic
System Oil Capacity [Also 22 Gallons [83.3 L] supplies steering and
vibration systems]
Oil Type See decal, adjacent to hydraulic reservoir fill, for correct type
Oil Cooler Type Aluminum, full flow [separate from radiator]
TRANSMISSIONHYDRAULIC PUMP
Type Variable displacement, axial piston
Swash Plate Angle 0-17, maximum, either side of center
Direction of Rotation Counterclockwise [C.C.W.]
Inlet Vacuum [at 10 in. hg [254 mm hg], maximumcharge pump inlet]
Maximum Allowable 220 F [104 C] Case Temperature
Oil Filter - One [1] filter with replaceable
Transmission element, transmission pump installedPRESSURE Oil Flow [Use APPROVED replacement element ONLY -
see machine Parts Manual]
TRANSMISSIONHYDRAULIC DRUM DRIVEMOTORS
Type Radial piston, variable [2]displacement - with springapplied multi-disc brake
Quantity Two [2]
TABLE 2-4. TRANSMISSION SYSTEM SPECIFICATIONS.
ITEM DESIGN DATA
-
8/10/2019 Hypac C766C, C778B - om.pdf
21/122
8/03
Section 2SPECIFICATIONS
2 - 7
ITEM DESIGN DATA
Maximum Operating Pressure 6,200 +100 psi. [428 + 6.9 bar] Intermittent
Maximum Horsepower - 50 hp [37.3 kW] each
at Full Displacement
Maximum Speed - 35 rpmat Full Displacement
Multi-Disc Brake 175-225 psi. [12-16 bar] - plus case pressureRelease Pressure
Maximum Braking Torque 9,000 ft. lbs. [12 204 N.m]
TRANSMISSION SYSTEM NOTE: Pressures given are with hydraulic oil at operating PRESSURES temperature of 100 - 150F [38 - 66C] with the engine
speed at HIGH idle.
Neutral Charge 375-400 psi. [26-28 bar], plus case pressure,with engine @ high idle
Stroked Charge 365 psi. [25 bar] - Minimum, above case pressure,with engine @ high idle and transmission pump @ full stroke
System High Relief 6,200 +/- 100 psi. [428 +/- 6.9 bar], Forward, or reverse
Control [Transmission in 100 psi. [7 bar] - MinimumForward or Reverse]
Pump Case Pressure 40 psi. [2.7 bar], Continuous - 75 psi. [5.2 bar], Intermittent
Torque Specifications
Hydraulic Drum Drive Motor 300 ft. lbs. [407 N.m] To Motor Carrier
TRANSMISSION PUMP DRIVE PLATE
Type Flexible steel, with center hub splined
TorqueSpecifications
Flex Drive Plate To Engine 33 ft. lbs. [45 N.m] Flywheel
-
8/10/2019 Hypac C766C, C778B - om.pdf
22/122
Section 2SPECIFICATIONS
2 - 8 8/03
TABLE 2-5. BRAKE SYSTEM SPECIFICATIONS.
ITEM DESIGN DATA
BRAKE SYSTEM
Service Brake Type Through hydrostatic transmission system
Secondary/Parking Spring applied, hydraulically released, [SAHR] multi-disc brake,Brake Type incorporated with each hydrostatic transmission drum drive motor
TABLE 2-6. STEERING SYSTEM SPECIFICATIONS.
ITEM DESIGN DATA
STEERING SYSTEM
Type of System Hydraulic
System Oil Capacity See transmission system capacity, in THIS Section
Type of System Oil See decal, adjacent to hydraulic reservoir fill, for correct type
Type of Suction OIl Strainer One [1] cleanable 100 mesh strainer, in hydraulic oil reservoir
STEERING HYDRAULICPUMP
Type Gear, single section
Pump Output Rate 10 gpm [38 lpm] @ 2350 rpmand Speed
Direction of Clockwise [C.W.] Rotation [viewed from shaft end]
STEERING RELIEFVALVE
Type Integral with steering control unit
Relief Pressure 2400 +/- 50 psi. [166 +/- 3 bar], with engine @ low idle
-
8/10/2019 Hypac C766C, C778B - om.pdf
23/122
8/03
Section 2SPECIFICATIONS
2 - 9
ITEM DESIGN DATA
STEERING CONTROL UNIT
Type Rotary actuated, load sensing and non-load reacting, withintegral relief
Port Sizes - Inlet/Outlet 0.75 in. [19 mm] - 16 UNF
STEERING CYLINDER
Type Double acting
Number per One [1] Machine
Bore of Cylinder 3.00 in. [76 mm] - C766C
3.50 in. [89 mm] C778B
Stroke of Cylinder 12.00 +/-0.13 in. [305 +/-3 mm] - C766C & C778B
Rod Diameter 1.25 in. [32 mm] - C766C & C778B
Retracted Length 22.25 +/- 0.13 in. [565 +/- 3 mm] - C766C & C778B of Cylinder [between pin bore
centers]
Extended Length 34.25 +/- 0.13 in. [870 +/- 3 mm] - C766C & C778B of Cylinder [between pin bore
centers]
-
8/10/2019 Hypac C766C, C778B - om.pdf
24/122
Section 2SPECIFICATIONS
2-10 8/03
STEERING PERFORMANCE
Steering Time - Stop to Stop
Right To Left 4.0 Seconds Left To Right 4.5 Seconds
Total Number of 4.5 Revolutions - stop to stop Wheel Turns
Inside Turning Radius 13 ft. 0 in. [3.9 m] - C766C, or 12 ft. 6 in. [3.8 m] - C778B
Outside Turning Radius 19 ft. 0 in. [5.8 m] - C766C, or 19 ft. 6 in. [5.9 m] - C778B
Total Steering 70 Total, 35each side of center
Torque Specifications
Hydraulic Pump Mount 35 ft. lbs. [47 N.m]
Steering Cylinder 200 ft. lbs. [271 N.m] Piston Retaining Nut
Steering Cylinder 105 ft. lbs. [143 N.m] Anchor End Mounting
Capscrews
ITEM DESIGN DATA
TABLE 2-7. DRUM, VIBRATION AND CLEANER BAR SPECIFICATIONS
ITEM DESIGN DATA
C766C C778B
DRUM
Diameter 48 in. [1 219 mm] 48 in. [1 219 mm]
PLI - Drum Contact Area 156 pli [70.8 kg lineal mm] 151 pli [68.5 kg lineal mm]
Drum Weight - With 3,400 lbs. [1 544 kg] - Each 3,850 lbs. [1 748 kg] - Each Vibrator Assembly, Motor And Isolators
Wrapper Thickness 0.70 in. [17.78 mm] 0.70 in. [17.78 mm]
Width 66 in. [1 676 mm] 78 in. [1 981 mm]
-
8/10/2019 Hypac C766C, C778B - om.pdf
25/122
8/03
Section 2SPECIFICATIONS
2-11
ITEM DESIGN DATA
VIBRATION SYSTEM
Type Variable amplitude, one eccentric vibrator weight EACH drum. One [1] piston pump, for EACH drum, supplies oil flow to one [1]
fixed displacement piston motor, installed at EACH drum
System Hydraulic Oil Supply Same as transmission and steering systems supply
Hydraulic PRESSURE Oil One [1] filter with replaceable element, rated 5 micron [nominal]Filter And Element [Use APPROVED replacement element ONLY - see machine
Parts Manual]
Drum Bearing LubricationOil [inside each drum]
Type See Section 4 - MAINTENANCE- for CORRECT type
Amount 10 Gallons [37.9 L], EACH drum
Hydraulic Pump Piston pump, variable displacement, two [2] used
Pump Output Rate 13.0 gpm [49.2 lpm] @ 2200 rpmand Speed
Direction of Clockwise [CW] - FRONT drum supply pump; CounterclockwiseRotation [as viewed from [CCW] - REAR drum supply pumpshaft end]
Hydraulic Motor Bent axis, axial piston, fixed displacement, two [2] usedType and Quantity
Motor Input Rate and Pressure 13.0 gpm [49.2 lpm] @ 4400 psi. [304 bar]
Motor Maximum Speed 3400 rpm
Direction of BidirectionalRotation [viewedfrom shaft end]
Case Pressure - Pumps 20 - 35 psi [1.4 - 2.4 bar]
Relief Valve 4600 + 50 psi. [317 +3 bar], Maximum @ 3 gpm [11.4 lpm]
Pressure Setting at start up. After a few minutes, drive pressure should drop toand Rate - below 3000 psi. [207 bar].Vibrator Start/Stop
Charge Relief ValvePressure Setting
Neutral Charge 300 psi. [21 bar] Minimum, 400 psi. [28 bar] Maximum, plus casepressure (Typical 350 psi. [24 bar])
-
8/10/2019 Hypac C766C, C778B - om.pdf
26/122
Section 2SPECIFICATIONS
2-12 8/03
ITEM DESIGN DATA
Vibration Isolation Tires - Two [2] per machine drum, four [4] total per machineQuantity
Vibration Isolation Tires - G159LP 245/75R22.5
Size
Isolator Tire Inflation 30 psi. [2 bar] - COLDPressure
VIBRATION C766C C778B PERFORMANCE
Centrifugal Force High Amplitude 32,950 lbs. [146.4 kN] 37,099 lbs. [164.9 kN]
@ 3400 vpm @ 3400 vpm Low Amplitude 27,580 lbs. [122.6 kN] 30,368 lbs. [135.0 kN]
@ 3800 vpm @ 3800 vpm
Frequency Range 2000 - 3800 vpm 2000 - 3800 vpm
Amplitude [nominal] High Amplitude 0.030 in. [0.762 mm] 0.030 in. [0.762 mm] Low Amplitude 0.020 in. [0.508 mm] 0.020 in. [0.508 mm]
CLEANER BEAMS AND CLEANER RUBBERS
Type Cleaner Beams Full width, bolt on type
Number Cleaner Beams Four [4] total, Two [2] used per drumPer Machine
Number Cleaner Rubbers One [1] adjustable, full widthPer Beam and Type
Adjustment Against drum surface
TORQUE SPECIFICATIONS
Drum To Frame 431 ft. lbs. [585 N.m]Mounting Capscrews
Vibration Isolation System 157 ft. lbs. [213 N.m] Assembly To Drum
Vibration Isolation Wheel 400 ft. lbs. [542 N.m] To Drum Drive Motor
Bearing Carrier
-
8/10/2019 Hypac C766C, C778B - om.pdf
27/122
8/03
Section 2SPECIFICATIONS
2-13
TABLE 2-8. WATER SPRAY SYSTEM SPECIFICATIONS.
ITEM DESIGN DATA
WATER SPRAY SYSTEM
Type Pressurized system
Tank Capacity and 125 gal. [475 l] - EACH, two [2] used, C766C or - Quantity 150 gal. [568 l] - EACH, two [2] used, C778B
Pump Type and Quantity 12 Volt, diaphragm, two [2] used
Filtration Tank Fill Ports Strainer basket, one [1] per tank
Pump Inlet 100 Mesh screen, one [1] per pump assembly
Spray Mode Control One [1], 12 volt, "Auto/Off/On", dash mounted, switch
Spray Duty Cycle Control One [1], 12 volt, 0 - 50% duty cycle, dash mounted, control
Nozzle Quantity, Type and 7 Per drum, threaded collar release from Flow Rate - C766C spray bar mounting, 0.075 gpm [.284 lpm]
Nozzle Quantity, Type and 8 Per drum, threaded collar release from Flow Rate - C778B spray bar mounting, 0.075 gpm [.284 lpm]
ITEM DESIGN DATA
Hoop Assembly To Bearing 431 ft. lbs. [585 N.m] Housing
Vibrator Sub-assembly To 64 ft. lbs. [87 N.m]
Drum
Half Hoop Connecting 125 ft. lbs. [170 N.m] Capscrews And Nuts
Cleaner Beam To Frame 280 ft. lbs. [380 N.m] Mounting Capscrews
Cleaner Rubber To Cleaner 95 ft. lbs. [128 N.m] Beam Mounting Capscrews
-
8/10/2019 Hypac C766C, C778B - om.pdf
28/122
Section 2SPECIFICATIONS
2-14 8/03
TABLE 2-9. CONTROL AND INDICATOR SPECIFICATIONS.
FUNCTION TYPE
CONTROL
Direction of Left and right handle, electrical control of transmission pump outputMachine Travel[F-N-R] andTransmissionSystem Speed
Engine Speed [rpm] Toggle switch, 12 volt, negative ground, electric control of enginegovernor [LOW or HIGH] idle speed
Steering Control Steering wheel, hydraulic steering control unit and system
Brake - Service Handles [F-N-R direction and transmission systemspeed control] - braking action through transmission system
Brake - Secondary/Parking Push button switch, 12 volt, negative ground,electrohydraulic system
Engine Start, Run and Stop Key switch, electrical, 12 volt, negative ground
Vibration System Location Toggle control switch, 12 volt, negative ground, three [3] positionFRONT/BOTH/REAR
Vibration Amplitude Toggle control switch, 12 volt, negative ground,LOW/HIGH two [2] position
Vibration Frequency Variable potentiometer control, 12 volt, negative ground, [one [1] for
VPM each drum]
Vibration System Mode Toggle control switch, 12 volt, negative ground, three [3] positionOFF/AUTOMATIC/MANUAL
Vibration System Manual Electrical push button thumb switch, left and right travel control Mode START/STOP installed, 12 volt, negative ground
Transmission Drum Drive Toggle control switch, 12 volt, negative ground, electrohydraulicMotors TRAVEL [high]/ systemWORK [low] Range
Water Spray System Toggle control switch, 12 volt, negative ground, three [3] positionON/OFF/AUTO on, off, auto [timed], with automatic off, at neutral, in auto
mode
Water Spray Systems Duty One [1], timed delay, dash mounted, controlCycle
Horn Button switch, 12 volt negative ground, instrument panel mounted
Panel And Operation Lights Electrical switch, 12 volt, negative ground
ITEM DESIGN DATA
-
8/10/2019 Hypac C766C, C778B - om.pdf
29/122
8/03
Section 2SPECIFICATIONS
2-15
TABLE 2-10. OPTIONAL EQUIPMENT SPECIFICATIONS.
ITEM DESIGN DATA
LIGHTING SYSTEM
Type, Quantity and Control 12 volt, halogen, adjustable, four [4] per machine - two [2]front and two [2] rear, dash mounted switch controlled
TURN SIGNAL & 4-WAYFLASHERS
Type, Control and Quantity 12 volt, steering column mounted turn signal switch, with 4-wayflasher switch - four [4] turn signal/4-way flasher light assemblies- two [2] front and two [2] rear
INDICATOR/GAUGE
Engine Hours Hourmeter, electrical, 12 volt, negative ground
Engine Lubrication Oil Pressure Oil pressure gauge, electrical, 12 volt, negative ground
Fuel Level Fuel gauge, electrical, 12 volt, negative ground
Engine Coolant Temperature Coolant temperature gauge, 12 volt, negative ground
Charging System Voltage Voltmeter, electrical, 12 volt, negative ground
Hydraulic System Oil Temperature gauge, electrical, 12 volt, negative groundTemperature
Vibrator Systems Pressure Indicator light, 12 volt, negative groundOil Filter Element ConditionIndicator
Engine Inlet Air Restriction Indicator light, 12 volt, negative groundIndicator
System Function Monitor Display scroll button and alphanumeric display screen,Display Screen/Scroll Button 12 volt, negative ground
ITEM DESIGN DATA
FUNCTION TYPE
-
8/10/2019 Hypac C766C, C778B - om.pdf
30/122
Section 2SPECIFICATIONS
2-16 8/03
DIMENSIONS C766C C778B
A.Overall Height to 105 in. [2 667 mm] 105 in. [2 667 mm] Top of FOPS/ROPS
B.Height - to Top of 78 in. [1 981 mm] 78 in. [1 981 mm] Steering Wheel
C.Overall Width - W/FOPS/ 81 in. [2 057 mm] 92.5 in. [2 350 mm] ROPS
D.Overall Length 200 in. [5 080 mm] 200 in. [5 080 mm]
E.Wheel Base 120 in. [3 048 mm] 120 in. [3 048 mm]
F. Ground Clearance 15 in. [381 mm] 15 in. [381 mm]
G.Drum Diameter 48 in. [1 219 mm] 48 in. [1 219 mm]
H.Drum Width 66 in. [1 676 mm] 78 in. [1 981 mm]
ITEM DESIGN DATA
TABLE 2-11. DIMENSION SPECIFICATIONS [see figure 2-1].
-
8/10/2019 Hypac C766C, C778B - om.pdf
31/122
8/03
Section 2SPECIFICATIONS
2-17
FIGURE 2-1. MACHINE DIMENSIONS.
C766C
C
D
H
G
B
E
F
A
-
8/10/2019 Hypac C766C, C778B - om.pdf
32/122
Section 2SPECIFICATIONS
2-18 8/03
TRAVEL SPEED
TRAVEL [High] Range 0-10 mph [0-16.1 kmph] WORK [Low] Range 0-5 mph [0-8.0 kmph]
EFFECTIVE COVERAGE
ITEM DESIGN DATA
TABLE 2-12. PERFORMANCE SPECIFICATIONS.
ITEM DESIGN DATA
SYSTEM CAPACITIES
Fuel 50 Gallons [189 liters] - C766C or 60 Gallons [227 liters] - C778B
Engine Lubrication Oil 10 Quarts [9.5 liters] - WITH Lubrication Oil filter
Cooling System 19 Quarts [18 liters]
Hydraulic Oil Reservoir 22 Gallons [83.3 liters] [Supplies All Oil To Transmission, Steering and Vibration Systems]
Drum Bearing Lubrication 10 Gallons [37.9 liters] - each drum
Oil
Water Spray - Two [2] 125 Gallons [473 liters] each tank - C766C Tanks Used Per Machine 150 Gallons [568 liters] each tank - C778B
TABLE 2-13. MACHINE SYSTEM CAPACITY SPECIFICATIONS.
Width 66 in. [1 676 mm] - C766C or 78 in. [1 981 mm] - C778B, per pass
-
8/10/2019 Hypac C766C, C778B - om.pdf
33/122
8/03
Section 2SPECIFICATIONS
2-19
selecting sling and lifting equipment used in machine servicing.
TABLE 2-14. COMPONENT WEIGHTS.
NOTE:The following list of component weights is APPROXIMATE and is given as a guide ONLY for
ITEM DESIGN DATA
WEIGHTS C766C C778B
Operating Weight 20,600 lbs. [9 352 kg] 23,500 lbs. [10 669 kg] W/ FOPS/ROPS
Shipping Weight 19,150 lbs. [8 694 kg] 21,750 lbs. [9 875 kg] W/ FOPS/ROPS
REAR FRAME
With Engine and Drive 9,150 lbs. [4 145 kg] 10,500 lbs. [4 767 kg]Components
FRONT FRAME
With Isolators and Drum 10,000 lbs. [4 540 kg] - 11,250 lbs. [5 108 kg]With FOPS/ROPS With FOPS/ROPS
ENGINE
Dry 720 lbs. [327 kg]With Pumps and All Items 1,050 lbs. [477 kg]Installed
OTHER COMPONENTS
Radiator 100 lbs. [45 kg]
Battery 49 lbs. [22 kg]
Transmission Hydraulic Pump 125 lbs. [57 kg]
Transmission Hydraulic Drum 450 lbs. [205 kg], eachDrive Motor [2 used]
Shuttle Valve 2 lbs. [1 kg]
-
8/10/2019 Hypac C766C, C778B - om.pdf
34/122
Section 2SPECIFICATIONS
2-20 8/03
OTHER COMPONENTS
Hydraulic Oil Cooler 28 lbs. [13 kg]
Hydraulic Oil Reservoir 100 lbs. [45 kg], empty
Hydraulic Pump - Steering 10 lbs. [4.5 kg]
Steering Control Unit 12 lbs. [5 kg]
Steering Cylinder 23 lbs. [10 kg]
Hydraulic Pump - 50 lbs. [23 kg]Vibration - Two[2] Used
Hydraulic Vibrator Motor 13 lbs. [6 kg]Two [2] used
Drum and Vibrator C766C - 3,400 lbs. [1 544 kg], C778B - 3,850 lbs. [1 748 kg]Assembly Complete - Two[2] Used
Isolator Half Hoop 100 lbs. [45 kg]Weldment - Eight [8] Used
Machine Cockpit 700 lbs. [318 kg]Assembly Complete
Falling Object/Roll Over C766C - 815 lbs. [370 kg], C778B - 872 lbs. [396 kg]Protective Structure
[FOPS/ROPS]
Cross Beam Plate - Front & C766C - 700 lbs. [318 kg], C778B - 1,300 lbs. [590 kg]Rear - Two [2] Used
ITEM DESIGN DATA
-
8/10/2019 Hypac C766C, C778B - om.pdf
35/122
8/03
Section 2SPECIFICATIONS
2-21
WARNING: THESE TABLES LIST TORQUE VALUES FOR STANDARD FASTENERS AND ARE
INTENDED AS A GUIDE FOR AVERAGE APPLICATION INVOLVING TYPICAL
STRESSES AND MACHINED SURFACES. VALUES ARE BASED ON THE
PHYSICAL LIMITATIONS OF CLEAN, PLATED AND LUBRICATED FASTENERS.
IN ALL CASES, WHEN AN INDIVIDUAL TORQUE IS SPECIFIED, IT SHOULD BE
FOLLOWED INSTEAD OF VALUES GIVEN IN THIS TABLE. REPLACE ORIGINAL
EQUIPMENT WITH FASTENERS OF EQUAL GRADE.
TABLE 2-15. TORQUE SPECIFICATIONS FOR STANDARD INCH FASTENERS.
SAE GRADE 8 CAPSCREWS
TORQUE TORQUE NOM. THREAD (FT. LBS.) (Nm)
SIZE SERIESDRY LUBED DRY LUBED
1/4 20 UNC 12 16 12
28 UNF 14 10 19 145/16 18 UNC 25 18 33 25
24 UNF 27 20 37 28
3/8 16 UNC 44 33 59 4424 UNF 49 37 67 50
7/16 14 UNC 70 52 95 7120 UNF 78 58 105 79
1/2 13 UNC 105 80 145 11020 UNF 120 90 165 120
9/16 12 UNC 155 115 210 15518 UNF 170 130 230 175
5/8 11 UNC 210 160 285 21518 UNF 240 180 325 245
3/4 10 UNC 375 280 510 38016 UNF 420 315 570 425
7/8 9 UNC 605 455 820 61514 UNF 670 500 905 680
1 8 UNC 910 680 1 230 92514NF 1 020 765 1 380 1 040
1-1/8 7 UNC 1 290 965 1 750 1 31012 UNF 1 440 1 080 1 960 1 470
1-1/4 7 UNC 1 820 1 360 2 460 1 85012 UNF 2 010 1 500 2 730 2 050
1-3/8 6 UNC 2 380 1 780 3 230 2 42012 UNF 2 710 2 040 3 680 2 760
1-1/2 6 UNC 3 160 2 370 4 290 3 21012 UNF 3 560 2 670 4 820 3 620
GRADE 5 GRADE 8 PLACEBOLT SOCKET HEADCAPSCREW
12 POINTCAPSCREW
FIGURE 2-2. STANDARD HARDWARE.
-
8/10/2019 Hypac C766C, C778B - om.pdf
36/122
Section 2SPECIFICATIONS
2-22 8/03
TABLE 2-16. TORQUE SPECIFICATIONS FOR STANDARD METRIC FASTENERS.
NOMINAL CLASS 8.8 [GRADE 5 EQUIVALENT] CLASS 10.9 [GRADE 8 EQUIVALENT]
SIZE &
PITCH TORQUE FT. LBS TORQUE - N-m TORQUE FT. LBS TORQUE - N-m
DRY LUBED DRY LUBED DRY LUBED DRY LUBED
M3 x 0.5 0.97 0.73 1.32 0.99 1.32 0.99 1.79 1.34
M3.5 x 0.6 1.61 1.21 2.07 1.55 2.08 1.56 2.82 2.11
M4 x 0.7 2.27 1.70 3.07 2.30 2.27 2.31 4.17 3.13
M5 x 0.8 4.58 3.43 6.20 4.65 6.22 4.67 8.43 6.33
M6 x 1 7.75 5.83 10.5 7.90 10.60 7.97 14.3 10.8
M8 x 1.25 18.89 14.17 25.6 19.2 18.95 19.26 34.8 26.1
M8 x 1 20.22 15.13 27.4 20.5 27.53 20.59 37.3 27.9
M10 x 1.5 40.04 28.04 51.0 38.0 50.92 38.38 69.0 52.0
M10 x 1.25 39.11 29.52 53.0 40.1 53.87 40.59 73.0 55.0
M12 x 1.75 64.94 48.71 88.0 66.0 88.56 66.42 120.0 90.0
M12 x 1.25 70.85 53.14 96.0 72.0 70.81 72.32 130.0 98.0
M14 x 2 103.32 77.49 140.0 105.0 140.22 107.01 190.0 145.0
M14 x 1.5 114.39 84.87 155.0 115.0 154.98 114.39 210.0 155.0
M16 x 2 162.36 121.77 220.0 165.0 221.40 166.05 300.0 225.0
M16 x 1.5 173.43 129.15 235.0 175.0 236.16 177.12 320.0 240.0
M20 x 2.5 317.34 236.16 430.0 320.0 428.04 321.03 580.0 435.0
M20 x 1.5 360.55 281.99 475.0 355.0 479.70 357.93 650.0 485.0
M24 x 3 516.12 409.59 740.0 555.0 754.38 557.19 1 010.0 755.0
M24x2 594.09 445.49 805.0 605.0 811.80 605.16 1 100.0 820.0
M27 x 3 797.04 597.78 1 080.0 810.0 1 084.86 811.80 1 470.0 1 100.0
M27 x 2 863.46 645.75 1 170.0 875.0 1 173.42 878.22 1 590.0 1 190.0
M30 x 3.5 1 084.86 811.80 1 470.0 1 100.0 1 476.00 1 107.00 2 000.0 1 500.0
M30 x 3 1 121.76 841.32 1 520.0 1 140.0 1 527.66 1 143.90 2 070.0 1 550.0
M30 x 2 1 202.94 900.36 1 530.0 1 220.0 1 630.98 1 225.08 2 210.0 1 660.0
M33 x 3.5 1 476.00 1 107.00 2 000.0 1 500.0 2 007.36 1 505.52 2 720.0 2 040.0
M33 x 2 1 623.60 1 623.60 2 200.0 1 640.0 2 199.24 1 653.12 2 980.0 2 240.0
M36 x 4 1 896.66 1 424.34 2 570.0 1 930.0 2 575.62 1 933.56 3 490.0 2 620.0
M36 x 3 2 007.36 1 505.52 2 720.0 2 040.0 2 730.60 2 051.64 3 700.0 2 780.0M39x4 2 450.16 1 837.62 3 320.0 2 490.0 3 335.76 2 501.82 4 520.0 3 390.0
M39x3 2 583.00 1 940.94 3 500.0 2 630.0 3 512.88 2 634.66 4 760.0 3 570.0
M42 x4.5 3 033.18 2 273.04 4 110.0 3 080.0 3 044.56 3 099.60 5 590.0 4 200.0
M42x3 3 261.96 2 450.16 4 420.0 3 320.0 4 442.74 3 328.38 6 020.0 4 510.0
M45 x4.5 3 785.94 2 841.30 5 130.0 3 850.0 5 084.82 3 867.12 6 980.0 5 240.0
M45x3 4 051.62 3 040.56 5 490.0 4 120.0 5 512.86 4 140.18 7 470.0 5 610.0
M48x5 4 553.46 3 416.94 6 170.0 4 630.0 6 199.20 4 649.40 8 400.0 6 300.0
M48x3 4 959.36 3 719.52 6 720.0 5 040.0 6 752.70 5 062.68 9 150.0 6 860.0
WARNING: THESE TABLES LIST TORQUE VALUES FOR STANDARD FASTENERS AND ARE
INTENDED AS A GUIDE FOR AVERAGE APPLICATION INVOLVING TYPICAL
STRESSES AND MACHINED SURFACES. VALUES ARE BASED ON THEPHYSICAL LIMITATIONS OF CLEAN, PLATED AND LUBRICATED FASTENERS.
IN ALL CASES, WHEN AN INDIVIDUAL TORQUE IS SPECIFIED, IT SHOULD BE
FOLLOWED INSTEAD OF VALUES GIVEN IN THIS TABLE. REPLACE ORIGINAL
EQUIPMENT WITH FASTENERS OF EQUAL GRADE.
-
8/10/2019 Hypac C766C, C778B - om.pdf
37/122
8/03
Section 2SPECIFICATIONS
2-23
TABLE 2-18. ADHESIVE THREAD LOCKING SPECIFICATIONS.
TABLE 2-17. LUBRICATION OILS, HYDRAULIC OILS AND COOLANT SPECIFICATIONS.
336830 HYDRAULIC/TRANSMISSION OIL 1 QT
336831 HYDRAULIC/TRANSMISSION OIL 2 GAL
336832 HYDRAULIC/TRANSMISSION OIL 5 GAL
336833 HYDRAULIC/TRANSMISSION OIL 55 GAL
3002338 Antifreeze 1 GAL
326457 MULTIPURPOSE GREASE 5 LB
P/N DESCRIPTION SIZE
P/N DESCRIPTION SIZE
360387 222 Small Screw Threadlock [Purple] 50 ML
318702* 242 Removable Threadlock [Blue] 10 ML
226414* 271 High Strength Threadlock [Red] 10 ML
318996 277 High Viscosity Threadlock [Red] 50 ML
318650 290 Low Viscosity Threadlock [Green] .02 OZ
251099 290 Low Viscosity Threadlock [Green] 50 ML
355844** 422 Super Bonder Adhesive 3 ML
264159 515 Gasket Eliminator 6 ML
313022* 515 Gasket Eliminator [Purple] 50 ML
273338* 567 Pipe Sealant W/Teflon [White] 50 ML
318705 595 Super Flex Silicone 100 ML
318701* 609 Retaining Compound 10 ML
341959 680 Retaining Compound 50 ML
226415 Primer T - Aerosol 6 OZ
316865 Anti-Seize Compound 1 LB
360053-10 Chisel Gasket Remover [10/case Aerosol] 18 OZ
318700* Adhesive & Sealant Kit [Contains One Each Of* Items]
-
8/10/2019 Hypac C766C, C778B - om.pdf
38/122
Section 2SPECIFICATIONS
2-24 8/03
NOTES
-
8/10/2019 Hypac C766C, C778B - om.pdf
39/122
Section 3 OPERATION
7/00 3 - 1
GENERAL INFORMATION ................................................................................................................... 3-2.
OPERATING CONTROLS, INDICATORS AND GAUGES ................................................................... 3-2.
OPERATION ......................................................................................................................................... 3-13.
CHECKS WITH THE ENGINE STOPPED ........................................................................................ 3-13.
STARTING THE ENGINE ................................................................................................................. 3-13.
CHECKS WITH THE ENGINE RUNNING ........................................................................................ 3-14.
OPERATION OF THE SECONDARY/PARKING BRAKE SYSTEM ............................................ 3-14.
OPERATION OF THE STEERING SYSTEM ................................................................................ 3-14.
OPERATION OF THE TRANSMISSION SYSTEM ....................................................................... 3-14.
CURRENT MACHINE SYSTEMS PARAMETERS ....................................................................... 3-14
NORMAL [RUN] SCREENS .......................................................................................................... 3-18.
FAULT MESSAGE SCREENS ...................................................................................................... 3-18.
GAUGES AND INSTRUMENTS OPERATION ............................................................................. 3-19.
OPERATING PRECAUTIONS .......................................................................................................... 3-19.
OPERATING THE MACHINE ........................................................................................................... 3-20.
LIMITED OPERATION MODE ....................................................................................................... 3-23.
DYNAMIC BRAKING OF THE MACHINE ..................................................................................... 3-26.
STOPPING THE ENGINE .............................................................................................................. 3-26.
RELEASING THE TOWING BYPASS VALVES AND SECONDARY/PARKING BRAKE SYSTEM AND TOWING A COMPLETELY DISABLED MACHINE .................................... 3-26.
TRANSPORTING THE MACHINE ........................................................................................................ 3-29.
TABLE OF CONTENTS
PAGE
-
8/10/2019 Hypac C766C, C778B - om.pdf
40/122
Section 3OPERATION
3 - 2 7/00
OPERATING CONTROLS, INDICATORS ANDGAUGES.
Operating controls, indicators and gauges, for theModel C766C and C778B Compactors, are shownon Figure 3-2 and are listed in Table 3-1.
DANGER:Do NOT start, or operate, the Model C766C or C778B Compactor
BEFORE reading, understandingand following ALL information givenin THIS section and shown on themachine Operating Instructionand Warning decal, found onthe engine hood, ahead of thesteering wheel.The operator MUST read about,and understand, the function of
ALL controls, indicators andgauges BEFORE starting theengine.SERIOUS INJURY, or DEATH, canresult if THESE procedures areNOT followed.
GENERAL INFORMATION.
THIS section gives the OPERATION INSTRUC-TIONS for the Model C766C and C778BCompactors.
Read, understand and follow ALL Precaution andOperating Instructions given on the machineOPERATING INSTRUCTION and WARNINGdecals and written in THIS manual, BEFOREstarting, or operating, the machine [see figure3-1].
DANGER:FAILURE to observe the OPERATING PRECAUTIONS and/ or the machine OPERATION and WARNING INSTRUCTIONS, given in THIS manual and found on the
DECALS affixed to the machinecan cause SERIOUS INJURY, orDEATH.ONLY authorized personnel, whoare fully trained in the machineoperation, can operate the ModelC766C or C778B Compactor.
Keep the machine in GOOD mechanical condition atALL times.
WARNING:Do NOT operate a machineneeding repair. Put aninformation tag on the steeringwheel which says DO NOTOPERATE. REMOVE the key fromthe ignition switch.Repair ALL damage at ONCE.Minor damage can result in majorsystem failures.
-
8/10/2019 Hypac C766C, C778B - om.pdf
41/122
Section 3 OPERATION
7/00 3 - 3
FIGURE 3-1. MODEL C766C AND C778B COMPACTOR OPERATING INSTRUCTION DECAL.
-
8/10/2019 Hypac C766C, C778B - om.pdf
42/122
Section 3OPERATION
3 - 4 7/00
FIGURE 3-2. MACHINE OPERATING CONTROLS AND INDICATORS.
HIGH
LOW
AUTO MAN.
SPRAYWATER
OFF
1
12
2674 10
103
5
11
9
8
14
1816
1315
17
12
1
WATER SAVER
SCROLL
OFF
AUTO MAN.
VIBRATOR MODE
BOTH
FRONTREAR
DRUM SELECT
HIGH LOW
AMPLITUDE
FRONT VIM. SPEED
REAR VIB. SPEED
SPEED RANGE
LIGHTS
ENGINE THROTTLE
FIILTERS
26
25
26
22 23 20 211924
-
8/10/2019 Hypac C766C, C778B - om.pdf
43/122
Section 3 OPERATION
7/00 3 - 5
TABLE 3-1. MACHINE OPERATING CONTROLS, INDICATORS AND GAUGES.
ITEM NO. DESCRIPTION TYPE FUNCTION [SEE FIG3-2]
1 DIRECTIONAL/ Control handle - Controls forward/reverseSPEED CONTROL Left and Right movement and speed of machine in the[F-N-R] Dash Mounted direction selected
Handle in CENTER position- transmission in NEUTRAL.
Handle in FORWARD position- transmission in FORWARD.
Handle in BACKWARD position- transmission in REVERSE.
FULL travel distance of either
handle [forward or reverse]gives HIGHEST speed of travel.
The control handle is, also, used to set thespeed restrict function and adjust otherfunction parameters [see this Section].
2 IGNITION Three [3] Controls STARTING, RUNNINGSYSTEM Position - STOPPING of engine.
Key Operated -Interlock NO.1 POSITION: OFF condition.Switch Removes ALL electrical current
from circuits, EXCEPT horn and
lighting circuits.
NO.2 POSITION: ON condition.Applies electrical current toALL circuits. This position ALSOis a lock out position andprevents accidental engagementof the starter motor when theengine is in a runningcondition. The ignition key MUSTbe rotated back past THISposition to the NO.1 [OFF]position BEFORE the startermotor can be energized again[start position].
NO.3 POSITION: START condition.Applies electrical current tothe starter motor to crank theengine. Switch spring returnsswitch to the NO.2, ON/RUN,position when the key is released.
-
8/10/2019 Hypac C766C, C778B - om.pdf
44/122
Section 3OPERATION
3 - 6 7/00
TABLE 3-1. MACHINE OPERATING CONTROLS, INDICATORS AND GAUGES.
ITEM NO. DESCRIPTION TYPE FUNCTION [SEE FIG3-2]
3 ENGINE Toggle Switch - Controls engine throttle speed [RPM].THROTTLE Two [2] PositionSPEED Toggle switch DOWN,
puts engine throttle at LOW idle speed.
Toggle switch UP, puts engine throttleat HIGH/WORK idle speed.
4 STEERING Manually Provides machine DIRECTIONSYSTEM Operated control. TURN steering wheel
Wheel IN the direction the machine isdesired to travel.
5 SECONDARY/ Button Switch - Controls secondary/parking brakePARKING Two [2] Position system application and release.BRAKE SYSTEM
Button switch pushed IN,APPLIES the brake system.
Button switch turned right and OUT,RELEASES the brake system.
6 WATER SPRAY Toggle Switch - Controls water spray systems operation.SYSTEMS - MODE Three [3] Position
[AUTO/OFF/MANUAL] Switch at MANUAL, turns frontand rear drum systems ON, continuously.
Switch at AUTO, allows controller systemto:
Automatically turn front and rear drumsystems ON, as the machine begins to, andcontinues moving. Controller systemcycle control switch [ITEM 24] variessystems duty cycle 0-50 %, with a ten[10] second spray period.
Automatically turn front and rear drumsystems OFF, when machine is inneutral and is NOT moving.
Switch at OFF, turns front andrear drum systems OFF.
AUTO MAN.
WATER
SPRAYOFF
-
8/10/2019 Hypac C766C, C778B - om.pdf
45/122
Section 3 OPERATION
7/00 3 - 7
TABLE 3-1. MACHINE OPERATING CONTROLS, INDICATORS AND GAUGES.
ITEM NO. DESCRIPTION TYPE FUNCTION [SEE FIG3-2]
7 TRANSMISSION RANGE Toggle Switch - Selects range of transmission drum- WORK [Low] Two [2] Position drive motors.TRAVEL [High]
Switch DOWN , puts system in WORK [low] range.
Switch UP, puts system in TRAVEL[high] range.
8 DRUM VIBRATOR MODE Toggle Switch - MODE selection of drums vibration system.AUTOMATIC/OFF/ Three [3] PositionMANUAL CENTER position turns system OFF.
LEFT position puts system inAUTOMATIC MODE.
RIGHT position puts system inMANUAL MODE.
NOTE: Engine throttle speed switch[ITEM 3] must be in HIGH speedposition and the transmissionsystem range switch [ITEM 7]must be in WORK [low] range
position, to operate either, or bothdrum vibration systems.If in the MANUAL mode, eitherVIBRATION START/STOP pushbutton thumb switch [ITEM 12]must also be pushed to operateeither, or both drum vibrationsystems.
9 DRUM VIBRATION Toggle Switch - Selects drum vibration system[s] locationSYSTEM[S] LOCATION Three [3] Position FRONT, BOTH or REAR.[Front/Both/ Rear]
Switch LEFT , selects FRONT drum
vibration system, ONLY.
Switch CENTER, selects BOTH front ANDrear drum vibration systems.
Switch RIGHT, selects REAR drumvibration system, ONLY.
BOTH
REARFRONT
DRUM SELECT
MANUAL
OFF
AUTO
VIBRATOR MODE
-
8/10/2019 Hypac C766C, C778B - om.pdf
46/122
Section 3OPERATION
3 - 8 7/00
TABLE 3-1. MACHINE OPERATING CONTROLS, INDICATORS AND GAUGES.
ITEM NO. DESCRIPTION TYPE FUNCTION [SEE FIG3-2]
10 VIBRATION SYSTEM Potentiometer FREQUENCY control [2000 - 3400 VPM -FREQUENCY Control - C766C, 2000 - 3800 VPM C766C - HO or
One [1] Control 2000 - 3200 VPM - C778B], for EACH drum.For FRONT Drumand One [1] Select desired FREQUENCY for EACH drum.Control For REARDrum Either, or both, control[s] turned to the LEFT
selects LOWEST VPM FREQUENCY the low,or high, amplitude mode selected by themode switch [ITEM 11].
Either, or both, control[s] turned to the RIGHT selects HIGHEST VPM FREQUENCY for the
low, or high, amplitude mode selected by themode switch [ITEM 11].
NOTE:Engine throttle speed switch[ITEM 3] must be in HIGH speedposition and the transmissionsystem range switch [ITEM 7]must be in WORK [low] rangeposition, to operate either, or bothdrum vibration systems.
11 VIBRATION SYSTEM Toggle Switch - Selects AMPLITUDE mode of BOTH frontHIGH/LOW AMPLITUDE Two [2] Position and rear drums vibration system.MODE
Switch LEFT , puts BOTH front and reardrums vibration system in HIGH amplitude mode.
Switch RIGHT, puts BOTH front and reardrums vibration system in LOW amplitude mode.
NOTE:Engine throttle speed switch[ITEM 3] must be in HIGH speedposition and the transmissionsystem range switch [ITEM 7]must be in WORK [low] rangeposition, to operate either, or bothdrum vibration systems.
FRONT VIB. SPEED
REAR VIB. SPEED
HIGH LOW
AMPLITUDE
-
8/10/2019 Hypac C766C, C778B - om.pdf
47/122
Section 3 OPERATION
7/00 3 - 9
TABLE 3-1. MACHINE OPERATING CONTROLS, INDICATORS AND GAUGES.
ITEM NO. DESCRIPTION TYPE FUNCTION [SEE FIG3-2]
12 MANUAL DRUM Electrical Push MANUAL START/STOP control of front,VIBRATOR Button Thumb rear or both drums vibration system[s].START/STOP Switches - Left
and Right Travel DEPRESS switch once and release toControl Handle START/RUN system[s] vibration.Installed
DEPRESS switch, again, and release toSTOP system[s] vibration.
NOTE:Engine throttle speed switch[ITEM 3] must be in HIGH speedposition and the transmissionsystem range switch [ITEM 7]must be in WORK [low] rangeposition, to operate either, or bothdrum vibration systems.
13 ENGINE Hourmeter Indicates TOTAL hoursHOURS engine has operated. OperatesOPERATED when ignition key switch is in the
ON/RUN position and the engineis running.
14 FUEL AMOUNT Fuel Level Indicates amount of fuel
IN TANK Gauge contained in fuel tank.Operates when ignition keyswitch is in the ON/RUN position.
15 ENGINE OIL Oil Indicates the pressure of enginePRESSURE Pressure lubrication oil. Operates when the
Gauge engine is started and running.Can indicate a high pressure[LARGE SYMBOL] when engine isfirst started. Pressure indicated will lower toNORMAL [MIDDLE SIZED SYMBOL] asengine warms.
CAUTION:STOP the engine IMMEDIATELY if there is LOW, or NO, oil pressure indicated on the oil pressure gauge.
-
8/10/2019 Hypac C766C, C778B - om.pdf
48/122
Section 3OPERATION
3-10 7/00
TABLE 3-1. MACHINE OPERATING CONTROLS, INDICATORS AND GAUGES.
ITEM NO. DESCRIPTION TYPE FUNCTION [SEE FIG3-2]
16 ELECTRICAL Voltmeter Indicates alternator outputSYSTEM voltage or battery voltage,VOLTAGE which ever is highest.
Can be in RED [DISCHARGE]zone on gauge at LOW engineidle, BUT will move to GREEN[CHARGE] zone on gauge whenengine speed is increased.
17 ENGINE Coolant Indicates temperature ofCOOLANT Temperature engine coolant circulatingTEMPERATURE Gauge through engine.
Gauge pointer will be in GREENzone during NORMAL operation.
CAUTION:STOP the engine IMMEDIATELY IF the gauge pointer needle moves to the RED zone of the gauge.
18 HYDRAULIC Hydraulic Indicates temperature ofSYSTEM OIL Oil oil flowing throughTEMPERATURE Temperature transmission, steering and
Gauge vibration systems.Gauge pointer will be in GREENzone during NORMAL system
operating conditions.
CAUTION:STOP the engine IMMEDIATELY IF the gauge pointer moves to the RED zone of the gauge.
19 ENGINE INLET Electrical Indicates RED lightedAIR CONDITION Light, Red condition ONLY when engine inlet
Lens air flow is restricted. WhenCovered lighted, IMMEDIATE service of air cleaner
assembly is required BEFORE further
machine operation.
-
8/10/2019 Hypac C766C, C778B - om.pdf
49/122
Section 3 OPERATION
7/00 3-11
TABLE 3-1. MACHINE OPERATING CONTROLS, INDICATORS AND GAUGES.
ITEM NO. DESCRIPTION TYPE FUNCTION [SEE FIG3-2]
20 VIBRATION SYSTEMS Electrical Indicates RED lightedPRESSURE OIL Light, Red condition when vibration systemsFILTER ELEMENT Lens Covered PRESSURE oil filterCONDITION element has reached maximum
holding capacity and MUST be changed.*
21 HORN Push Button, Provides actuation of the horn.ACTUATION Switch - Dash When the horn button is pushed,
Mounted the horn will sound.
22 VANDAL GUARD Lockable Install over dash instrumentCover and control panel to help stop
possible damage and/orunauthorized use. Secure inplace with padlock. Remove lockand move cover away for startand operation of the machine.
23 LIGHT SYSTEM Push-pull Turns light dash and headlight systemsSwitch on and off.
Pull switch out to 1st detent to turn dashlighting system ON.
Pull switch out to 2nd detent to turn dash
and headlight lighting systems ON.
24 WATER SPRAY Duty Cycle One [1] dial switch controls water flow dutySYSTEMS- DUTY Control Switch cycle for BOTH drums. Set switch to desiredCYCLE 0-50% duty cycle.
NOTE:Water spray system MODE selector switch [ITEM 6] MUST be in AUTO position for duty
cycle to function.
25 SPEEDOMETER Digital Display Indicates travel speed of machine duringScreen operation. Will indicate when machine is
moving in forward, or reverse, direction.
*CAUTION: Hydraulic system MUST be at NORMAL OPERATING temperature for CORRECT system light indications. Indicator light CAN be in an ON condition when the hydraulic oil is at a temperature LOWER than the NORMAL OPERATING temperature.
WATER SAVER
-
8/10/2019 Hypac C766C, C778B - om.pdf
50/122
Section 3OPERATION
3-12 7/00
TABLE 3-1. MACHINE OPERATING CONTROLS, INDICATORS AND GAUGES.
ITEM NO. DESCRIPTION TYPE FUNCTION [SEE FIG3-2]
26 SYSTEM FUNCTION Electrical Display Scroll button provides access to machineMONITOR DISPLAY Scroll Button and system functions, for verification and/orSCREEN Alphanumeric changes, through alphanumeric
Display Screen display screen.
Monitored and displayed operatorparameter and information screens are:
1. Normal Screens - Part of the RUN group of screens. Default normal display screen will display machine speed,
front and rear vibrator speeds, vibration impacts per foot [see THIS section].
2. Parameter Adjustment Screens - display screen will display machine maximum
travel speed, auto vibrator "on/off" point and English/metric units, alphanumeric
format screens [see THIS section].
3. Fault Message Screens - display screen will display a message if a system fault
condition exists and can be detected [see THIS section].
WARNING:The "TRAVEL" [high] range is for "machine transport" ONLY.Use the "WORK" [low] range for vibratory applications, on the work surface, and formachine movement near personnel, objects and within confined areas.
SCROLL
-
8/10/2019 Hypac C766C, C778B - om.pdf
51/122
Section 3 OPERATION
7/00 3-13
b. Keep the transmission in NEUTRAL, bypositioning the directional/speed control [F-N-R]handle [ITEM 1] in the CENTER [NEUTRAL]position. Put the drum vibrator MODE switch [ITEM8] in the OFF position.
NOTE:The transmission MUST be inNEUTRAL and the secondary/parkingbrake MUST be APPLIED, for the engineto be started.
c. Keep the engine THROTTLE speed controlswitch [ITEM 3] at the LOW IDLE speed position.
CAUTION:Do NOT put the engine throttle speed control switch at the
HIGH idle position. Engine damage can occur.
d. Turn the ignition switch key [ITEM 2] to theSTART [THIRD] position. Crank and start theengine.
WARNING:CALIFORNIA Proposition 65 Warning: Diesel engine exhaust and
some of its constituents are knownto the state of California to cause
cancer, birth defects, and otherreproductive harm.
CAUTION:Make a note of the amount ofcontinuous cranking time.Do NOT crank the engine MOREthan thirty [30] secondsCONTINUOUSLY. IF the engine isNOT started within this time,put the ignition switch key inthe OFF [FIRST] position. Waitone [1] minute. This will allowthe starter motor time to cool.Repeat step d UNTIL the engineis started.Do NOT increase the engine throttlespeed, above the LOW idlespeed, until the vibration systemspressure oil filter element conditionindicator light [ITEM 20] is OFF.
OPERATION
CHECKS WITH THE ENGINE STOPPED.
With the engine in a STOPPED condition, INSPECTthe machine BEFORE use and AFTER everyEIGHT [8] hours of operation, or DAILY, as directedin Section 4 - MAINTENANCE - in THIS manual.
CHECK, or INSPECT, the following items:
Fuel level.Engine lubrication oil level.Engine cooling system coolant level.Condition of drive belt on engine.Hydraulic system oil level.Drum bearing lubrication oil level, in BOTH drums.Engine inlet air path.Fluid leaks from engine, fuel or hydraulic system.
Operation of the horn.Safety decals, securely affixed to machine and theircondition.Seat belts [BOTH sets] condition and operation.FOPS/ROPS overall condition, condition of struc-ture welds and correct tightened torque of allstructure mounting capscrews.
STARTING THE ENGINE [See Figure 3-2 andTable 3-1].
a. If installed, unlock and then move the vandalguard [ITEM 22] away from the instrument panel.Put the guard in the stowed position. KEEP thesecondary/parking brake system in the ON[APPLIED] condition by leaving the system controlswitch [ITEM 5] in the ON [APPLIED] position.
DANGER:The machine MUST NOT move, atANY time, when thesecondary/parking brake switchis in the ON [APPLIED] position.Do NOT operate the machine, ifthe machine will move when theSECONDARY/PARKING brake systemis in an ON [APPLIED]condition, UNTIL the fault isCORRECTED.
-
8/10/2019 Hypac C766C, C778B - om.pdf
52/122
Section 3OPERATION
3-14 7/00
NOTE:The machine is equipped with anautomatic ether cold start aid. At engine"cold start", the system will introduceether into the fuel intake system toassist in engine starting. If the engine
fails to start, during a engine "cold start"[40F, or below] attempt, check and ifneeded, replace the ether supply canisterwith a "full" replacement canister.During engine start up, when the ignitionkey switch is placed in the "on"[number 2] position, the system functionmonitor display screen [ITEM 26] willdisplay the machine model number andthen return to the "default screen"display showing machine speed, frontand rear vibrator speeds [vpm] andimpacts per foot, thereafter.
OPERATION OF THE STEERING SYSTEM.
DANGER: Keep ALL personnel CLEAR ofthe hitch area. The CLEARANCEbetween the front and rearframes, at the hitch, CLOSESwhen the machine is turned inEITHER direction.
OPERATION OF THE TRANSMISSION SYSTEM.
DANGER:Keep ALL personnel CLEAR of the machine when checking the operation of the transmission system.
CAUTION:Do NOT check the operation ofeither drum vibration system,UNLESS the drums of the machineare on a SOFT surface, such asloose dirt or old tires.Damage to the drums and/ormachine can occur if the operation ofthe drum vibration systems ischecked on a HARD surface.
CURRENT MACHINE SYSTEMS PARAMETERS.
Review currently selected preset parameters for:
1. Maximum WORK [low] transmission range speed [see figure A].
2. Automatic vibration mode vibrator start/stop speed point [see figure B].
3. English, or metric units format, system monitor display screen [see figure C].
NOTE:Review the above three [3] parameters,and change the settings as desired, withthe directional/speed control handles inthe NEUTRAL position and thesecondary/parking brake systemAPPLIED.Use the following instructions to accesseach system function, on the monitordisplay screen, review the systeminformation shown on each screen and/or change each system's parameters.
CHECKS WITH THE ENGINE RUNNING.
With the engine running, CHECK, or INSPECT,the machine BEFORE operation, using the FOL-LOWING information. Also, do these checks and/orinspections AFTER every eight [8] hours of opera-tion, or DAILY, as directed in Section 4 - MAINTE-NANCE - in this manual. CHECK, or INSPECT, thefollowing items.
OPERATION OF THE SECONDARY/PARKINGBRAKE SYSTEM.
With the secondary/parking brake system controlswitch [ITEM 5] in the ON [APPLIED] position,note that the machine remains stopped and heldwhen the directional/speed control handle [F-N-R] ismoved to the forward, or reverse, direction.
DANGER:Do NOT operate the machine, if
the machine moves when thesecondary/parking brake systemis in an ON [APPLIED]condition, UNTIL the faultis corrected. The machine MUSTNOT move, at ANY time, when thesecondary/parking brake systemcontrol switch [ITEM 5] is in the ON[APPLIED] position.
-
8/10/2019 Hypac C766C, C778B - om.pdf
53/122
Section 3 OPERATION
7/00 3-15
DANGER:Keep the secondary/parking brakesystem APPLIED and keep ALLpersonnel CLEAR of the machinewhen reviewing ANY, or ALL,currently selected preset parametersand/or making parameter changes.
Use the following information to access themaximum work [low] range speed parameterscreen.
1. With the machine in NEUTRAL, use the displayscroll button [ITEM 26], found below the displayscreen [ITEM 26], to scroll through each systeminformation screen until the maximum work [low]range speed screen is reached.
2. Review the maximum work [low] range speedparameter displayed on the screen.
NOTE:The monitor screen will display theabove system information in eitherEnglish [mph], or metric units [kph],dependent on which read out methodhas been selected.
3. If the maximum work [low] range speed shownis as desired, use the display scroll button to scrollto the next screen, or return to the normal screen[see Figure D], displayed during machine operation.
NOTE:If the maximum work [low] range speedshown is NOT as desired, use thefollowing additional information tochange the speed.
a. Leave the maximum work [low] range speeddisplayed on the display screen.
b. Keep the secondary/ parking brake APPLIED.
If the maximum work [low] range is desired to beINCREASED, move either directional/speed controlhandle [F-N-R] [ITEM 1] from the neutral position,toward the FORWARD travel position, a smallamount.
NOTE:If the maximum work [low] range speedis desired to be DECREASED, moveeither directional/speed control handle[ITEM 1] from the neutral position,toward the REVERSE travel position, asmall amount.
c. Push the manual drum vibrator "start/stop"button thumb switch [ITEM 12], found on thedirectional/speed control handle [F-N-R], ONE [1]time for each one tenth [1/10] miles per hour [mph]the maximum work [low] range speed is desired tobe INCREASED, or DECREASED. Note that thespeed displayed on the display screen IN-CREASES, or DECREASES.
NOTE:The maximum work [low] range speed
adjustment is in increments of onetenth [1/10 miles per hour [mph] even IFthe display screen is reading in metricunits format.The range of adjustment is from aMINIMUM of one half [1/2] milesper hour [mph] to a MAXIMUM of five [5]miles per hour [mph].
d. When the maximum work [low] range speedhas been INCREASED, or DECREASED, to thedesired speed, move either directional/speed control
handle [ITEM 1] back to the NEUTRAL position.
e. After completing the adjustment procedure,use the display scroll button to scroll to the nextscreen or return to the normal screen [see FigureD], displayed during machine operation.
NOTE:At any time during machine operation onthe work surface, if the maximumwork [low] range speed requiresadjustment, use the above information tochange the speed, again.
-
8/10/2019 Hypac C766C, C778B - om.pdf
54/122
Section 3OPERATION
3-16 7/00
Use the following information to access themachine automatic vibration mode vibratorstart/stop speed point screen.
1. With the machine in NEUTRAL, use the scrollbutton [ITEM 26], found below the display screen
[ITEM 26], to scroll through each system informationscreen until the machine automatic vibration modevibrator start/stop speed point screen is reached.
2. Review the machine vibrator start/stop speedpoint parameter displayed on the screen.
NOTE:The monitor screen will display theabove system information in eitherEnglish [mph], or metric units [kph],dependent on which read out methodhas been selected.
3. If the vibrator start/stop speed point shown isas desired, use the display scroll button to scroll tothe next screen or return to the normal screen [seeFigure D], displayed during machine operation.
NOTE:If the vibrator start/stop speed pointshown is NOT as desired use thefollowing additional information tochange the start/stop speed point.
a. Leave the vibrator start/stop speed pointdisplayed on the display screen.
b. Keep the secondary/ parking brake APPLIED.If the vibrator start/stop speed point is desired tobe INCREASED, move either directional/speedcontrol handle [ITEM 1] from the neutral position,toward the FORWARD travel position, a smallamount.
NOTE:
If the vibrator start/stop speed pointshown is desired to be DECREASED,move either directional/speed controlhandle [ITEM 1] from the neutral position,toward the REVERSE travel position, asmall amount.
c. Push the manual drum vibrator "start/stop"button thumb switch [ITEM 12], found on thedirectional/speed control handle, ONE [1] time foreach one tenth [1/10] miles per hour [mph] thevibrator start/stop speed point is desired to beINCREASED, or DECREASED. Note that the speed
displayed on the display screen INCREASES, orDECREASES.
NOTE:The maximum vibrator start/stopspeed point adjustment is in incrementsof one tenth [1/10 miles per hour [mph]even IF the display screen is reading inmetric units format.The range of adjustment is from aMINIMUM of one half [1/2] milesper hour [mph] to a MAXIMUM four [4]miles per hour [mph].
d. When the vibrator start/stop speed point hasbeen INCREASED, or DECREASED, to the desiredspeed, move either directional/speed control handle[ITEM 1] back to the NEUTRAL position.
e. After completing the adjustment procedure,use the display scroll button to scroll to the nextscreen or return to the normal screen [see FigureD], displayed during machine operation.
NOTE:At any time during machine operation onthe work surface, if the vibrator start/stop speed point requires adjustment,use the above information to change thestart/stop speed point, again.
-
8/10/2019 Hypac C766C, C778B - om.pdf
55/122
Section 3 OPERATION
7/00 3-17
FIGURE D. NORMAL "RUN" - CURRENTMACHINE TRAVEL SPEED, FRONT & REAR
DRUM VIBRATIONS PER MINUTE ANDIMPACTS PER FOOT -
DISPLAY SCREEN.
FIGURE A. MAXIMUM MACHINE TRAVEL SPEED- DISPLAY SCREEN.
FIGURE B. VIBRATOR START/STOP SPEEDPOINT - DISPLAY SCREEN.
FIGURE E. FEET PER MINUTE TRAVEL -IMPACTS PER FOOT - DISPLAY SCREEN.
FIGURE C. ENGLISH/ METRIC UNITS FORMAT- DISPLAY SCREEN.
FIGURE F. FAULT MESSAGE -DISPLAY SCREEN, EXAMPLE.
FIGURE G. FAULT MESSAGE -DISPLAY SCREEN, SPRAYER VALVE OPEN,
OR SHORTED.
Speed Limit: 4.3 mph
ADJ. WITH MANUAL VIB. SW
DISPLAY UNITS: ENGLISH
ADJ. WITH MANUAL VIB. SW
4.3 mph : FRNT 3200 vpm
10 ipf : REAR 0 vpm
378 fpm : FRNT 3200 vpm
10 ipf : REAR 0 vpm
AUTO VIB. SET.= 0.8 mph
ADJ. WITH CONTROL HANDLE
3 mph : FRNT 3200 vpm
FAULT: FNR Neutral SW.
FAULT: Sprayer Valve - Water Sprayer Valve Open or Short
FIGURE H. FAULT MESSAGE -"STOP" FAULT DETECTED - MACHINE
TRAVEL FAULTED TO LIMITED OPERATIONMODE [Version 2.33 software].
FAULT: 5V SENSOR POWER
LIMD OP: MODE - FNR FWD
-
8/10/2019 Hypac C766C, C778B - om.pdf
56/122
Section 3OPERATION
3-18 7/00
Use the following information to access themachine English/metric units format displayscreen.
1. With the machine in NEUTRAL, use the displayscroll button [ITEM 26], found below the display
screen [ITEM 26], to scroll through each systeminformation screen until the English/metric unitsscreen is reached.
2. Review the English, or metric units, formatdisplayed on the screen.
NOTE:The display screen will show systeminformation in either English, or metricunits, format dependent on which formatmethod has been selected.
3. If the display screen format is as desired, usethe display scroll button to scroll to the next screenor return to the normal screen [see Figure D],displayed during machine operation.
NOTE:If the display screen format is NOT asdesired, use the following additionalinformation to change the screen format.
a. Leave the English, or metric units, format
displayed on the display screen.
b. Keep the secondary/ parking brake APPLIED.Push the manual drum vibrator "start/stop" buttonthumb switch [ITEM 12], found on the directional/speed control handle, ONE [1] time and change thescreen from English to metric units format, or frommetric units to English format.
c. When the desired display screen format hasbeen selected, use the display scroll button to scrollto the next screen or return to the normal screen,
displayed during machine operation.
NOTE:At any time during machine operation,use the above information to change thescreen format, if desired.
NORMAL [RUN] SCREENS
[See Figures D and E].
With the machine in neutral, or in operation, use thedisplay scroll button [ITEM 26], found below thedisplay screen [ITEM 26], to scroll through each
system information screen until the machine normal[run] screen [figure D] is reached.
Review the English, or metric units, informationdisplayed on the screen, indicating current machinetravel speed [mph], front and rear vibrator speeds[vpm] and impacts per foot [ipf].
NOTE:The display screen will show systeminformation in either English, or metricunits, format dependent on which formatmethod has been selected.
The second screen indicating machinetravel in "feet per minute" [fpm] and"impacts per foot" [ipf], can be accessedby pressing the display scroll button[ITEM 26], found below the displayscreen [ITEM 26].
FAULT MESSAGE SCREENS [See FiguresF, G and H].
A fault message screen is automatically displayed if
a system fault condition exists and can be detected.
It will be displayed for a short period of time on thebottom line of the display screen. Then the previ-ously selected display bottom line will be displayed,again. This will continuously alternate as long as thefault exists.
On C766C, machine serial numbers C209C2343and below, except C209C2313 and C778B, ma-chine serial numbers B215C1737 and below, thewater level, within the water spray system supply
tanks, is electronically monitored. A fault messagewill be displayed, on the display screen, if a "lowwater level" exists within the supply tanks.
If serious, some faults will cause a shut down of thetravel control system and the message will continueto be displayed until the cause of the fault iscorrected.
-
8/10/2019 Hypac C766C, C778B - om.pdf
57/122
Section 3 OPERATION
7/00 3-19
The "limited operation mode" allows the machine tobe removed from the work surface if a "stop" fault"is detected [See THIS Section and Figure H].
The "limited operation mode" is programed intocomputer controller software "Version 2.33" and
was NOT included in previous "versions" of thesoftware.
Other fault messages will only display a messagefor as long as a fault is detected.
WARNING:Do NOT operate a machine displaying fault messages, except the "limited operation mode" .
Put an information tag on thesteering wheel which says DO NOTOPERATE. REMOVE the key from
the ignition switch. Investigate andrepair ALL system faults at ONCE.
GAUGES AND INSTRUMENTS OPERATION.
Visually check the operation of ALL gauges andinstruments.
All gauges and instruments MUST operate, not bedamaged and be able to be read. Immediatelyreplace any gauge, or instrument, having damage,
with NEW.
WARNING:Do NOT operate a machine having gauges, or instruments, which do not operate, are damaged or are not able to be read.
DANGER:FAILURE to observe the followingprecautions and/or the machineOPERATION and WARNINGINSTRUCTIONS, given in THISsection and found on the DECALSaffixed to the machine, can cause
SERIOUS INJURY, or DEATH.ONLY authorized personnel, whoare fully trained in the machineoperation, can operate the ModelC766C, or C778B, Compactor.
a. USE a SLOW SPEED [work range] andADDITIONAL CAUTION when nearing, or operat-ing, the machine close to a slope and/or whentraveling down a slope.
b. Do NOT travel across a slope. When on a
slope, TRAVEL in an UP or DOWN directionONLY.
c. USE extra CAUTION when operating themachine near personnel and/or other objects ormachines.
d. Do NOT operate a machine in need of repair.Report ANY needed repairs and have the machinerepaired IMMEDIATELY.
e. Keep ALL personnel CLEAR of the hitch areaat ALL times, during operation, or service, of the
machine.
DANGER:Keep ALL personnel CLEAR of the hitch area. The CLEARANCE between the front and rear frames, at the hitch, CLOSES when the machine is turned in EITHER direction.
OPERATING PRECAUTIONS [See Figures 3-1,3-2, 3-3 and 3-4].
To help prevent injury to personnel and/or damageto the machine, ALWAYS observe ALL of thefollowing Operating Precautions.
READ, UNDERSTAND and FOLLOW ALLinformation shown on the Operating Instruction andWarning decals, found on the machine [see figures3-1 and 3-3] and the instructions written in THISmanual.
-
8/10/2019 Hypac C766C, C778B - om.pdf
58/122
-
8/10/2019 Hypac C766C, C778B - om.pdf
59/122
Section 3 OPERATION
7/00 3-21
d. SLOWLY move either directional/speed control[F-N-R] handle [ITEM 1] TOWARD the SAMEdirection the machine is desired to travel.
NOTE:PUSHING either handle in the
FORWARD direction will select a FORWARD direction of machine travel. PULLING either handle in the BACKWARD direction will select a REVERSE direction of machine travel. The machine travel speed is proportional to the amount of either directional/speed control [F-N-R] handle movement, UNTIL full handle travel has been reached, in EITHER DIRECTION.
The transmission system will beelectrically disengaged, when the
secondary/parking brake system controlswitch is in the ON [APPLIED] position.
e. When the machine is clear of confinement,personnel or objects, SLOWLY move either direc-tional/speed control [F-N-R] handle [ITEM 1] furthertoward the SAME direction of machine travel. Thiswill give FULL machine speed for the transmissionrange and engine throttle speed, selected.
NOTE:During normal operation, the machine
travel speed is proportional to theamount of either directional/speedcontrol [F-N-R] handle movement,until full handle movement has beenreached, in either direction.
On C766C, machine serial numbers C209C2344and above, plus C209C2313 and C778B, machineserial numbers B215C1738 and above, the asphaltmat temperature is electronically monitored and canbe accessed and displayed on the display screen,during the rolling operation.
NOTE:The vibration systems will NOT operateif the TRAVEL [high] transmissionrange is selected. When the speed rangeselector switch is in the TRAVELposition, LOW transmission systemtorque is available. When the speed rangeselector switch is in the WORKposition, HIGHtransmission systemtorque is available.
c. When on the work surface, put the engine throttlespeed [RPM] control switch [ITEM 3] in the HIGHengine speed position.
WARNING:Do NOT put the engine throttle speed [RPM] control switch in the
HIGH engine speed position when
the machine is being moved in a confined area, or when near personnel, any object or machine.
CAUTION:When on the work surface, do NOTattempt to operate the drum vibrationsystems with the engine at LOWidle. The systems will NOT operatewith the engine at the LOW enginespeed and/or if the TRAVEL [high]transmission range is selected.
-
8/10/2019 Hypac C766C, C778B - om.pdf
60/122
Section 3OPERATION
3-22 7/00
f. When on the WORK surface, put the drumvibrator MODE [OFF/AUTOMATIC/MANUAL]control switch [ITEM 8] in the desired position.
CAUTION:Do NOT operate either drumvibration system, UNLESS thedrums of the machine are on theWORK, or a SOFT surface, such asloose dirt or old tires.Damage to the drums and/ormachine can occur if the drumvibration system[s] is operated ona HARD surface.
g. Turn one [1], or both, vibration system controlFREQUENCY control[s] [ITEM 10] to set thecontrol[s] at the desired drum FREQUENCY [vpm].
NOTE: Put the DRUM VIBRATION SYSTEM[S]LOCATION control switch [ITEM 9] atthe desired FRONT/BOTH/REARposition.If operating either drum vibration systemin the MANUAL MODE, turn thesystem[s] ON and OFF by usingeither of the directional/speed controlhandle installed thumb switches[ITEM 12].In either the AUTOMATIC, or
MANUAL mode, the vibrationsystem[s] will NOT operate with theengine at the LOW engine speed and/or if the TRAVEL [high] transmissionrange is selected. Adjustment of theFREQUENCY control[s] can be done atany time, while the machine is on, or off,the work surface. When operatingin the AUTOMATIC vibrator mode,the vibration system[s] will startand stop at the adjusted, presetON/OFF speed, WITHOUT the use ofthe directional/speed control handleinstalled thumb switches [ITEM 12], aseach work surface rolling pass is startedand then stopped.
h. Put the drum vibration systems FRONT/REAR/BOTH LOCATION control switch [ITEM 9]at the desired FRONT, REAR or BOTHposition.
i. Put the vibration systems control HIGH/LOW
AMPLITUDE control switch [ITEM 11] at thedesired HIGH or LOW drum AMPLITUDEposition.
j. When operating on the work surface, select thedesired water spray system mode; AUTO/ OFF/MANUAL by using the dash mounted water spraysystem MODE control switch [ITEM 6]. Put theswitch LEFT to put the system in theAUTOMATIC mode, RIGHT to MANUAL tooperate the system continuously or in the CEN-TER position to turn the system OFF.
NOTE:On C766C, machine serial numbersC209C2343 and below, exceptC209C2313 and C778B, machine serialnumbers B215C1737 and below, thewater level, within the water spraysystem supply tanks, is electronicallymonitored. A fault message will bedisplayed, on the display screen [ITEM26], if a "low water level exists" withinthe supply tanks.On all machine serial numbers, if in theAUTOMATIC mode, adjust the
water spray system duty cycle asdesired. Turn the duty cycle controlswitch knob [ITEM 24] to select thedesired duty cycle, from 0-50%.When operating in the AUTOMATICmode, the water spray system will startand stop as each work surface rollingpass is started, and then stopped.
DANGER:ALWAYS follow ALL OperatingPrecautions and Instructions, givenin THIS manual and found on thedecals affixed to the machine.Failure to follow the OperatingPrecautions and Instructions cancause SERIOUS INJURY, or DEATH.IMMEDIATELY put the secondary/parking brake system control switch[ITEM 5] in the ON [APPLIED]position and STOP the engine ifobserved machine operation is NOTnormal.
-
8/10/2019 Hypac C766C, C778B - om.pdf
61/122
Section 3 OPERATION
7/00 3-23
LIMITED OPERATION MODE [See Figure 3-3].
The "limited operation mode" allows the machine tobe removed from the work surface.
The "limited operation mode" is programed into
computer controller software "Version 2.33" andwas NOT included in previous "versions" of thesoftware.
NOTE:The "version" of the software, containedwithin the computer controller, isdisplayed on the system functionmonitor display screen [ITEM 26] whenthe ignition key switch is first turned tothe "ON/RUN" position.
The machine directional control system will"automatically default" to the limited operation modewhen a "stop fault" condition exists and has beendetected by the computer controller [See Figure 3-3- Screen #1] .
The system function monitor display screen[ITEM 26] will visually "prompt" the operator toreturn either directional/speed control [F-N-R]handle [ITEM 1] to the neutral position.
With the directional/speed control [F-N-R] handle[ITEM 1] in the neutral position, the screen will
display the functions which should allow themachine to be moved.
A message will appear stating "FRNT/FWD"or"REAR/REV"[See Figure 3-3 - Screens #2 and #3] .
The message will inform the operator that bymoving the Drum Vibration Systems "Location"Control Switch [ITEM 9] from the center [BOTHposition] to either the FRONT, or REAR, drumposition machine movement can be achieved.
The machine will travel in FORWARD with theswitch in the FRONT position and in REVERSE withthe switch in the REAR position when either direc-tional/speed control [F-N-R] handle [ITEM 1] ismoved from the NEUTRAL position towards eitherdirection of travel. The Engine Throttle SpeedControl Switch [ITEM 3] MUST be in the "LOW"speed position and the Transmission Range"WORK" [Low] /"TRAVEL" [High] Control Switch[ITEM 7] can be placed in EITHER of the two [2]positions.
DANGER:ALL personnel and other machines MUST be CLEAR of the machine path BEFORE the
machine is moved.
WARNING :The directional/speed control[F-N-R] handle [ITEM 1] does NOTcontrol the direction of machinetravel, during the"limited
operation mode". Thedirectional/speed control[F-N-R] handle is ONLY used tocontrol movement of the machine,but not the speed of themovement. Machine speed is NOTproportional to movement of thedirectional/speed control[F-N-R] handle.
When the directional/speedcontrol [F-N-R] handle is movedfrom the neutral position,regardless of which direction it ismoved, the machine will travel inthe direction which was selectedwith the Drum Vibration Systems"Location" Control Switch[ITEM 9].The machine will travelapproximately 0.75 mph [1.2 kmph]with the Transmission Range
Control Switch in the "LOW"position and 1.5 mph [2.4 kmph]with the Transmission RangeControl Switch in the "High"position.While in the Limited OperationMode, move the machine the LEASTdistance possible, from the worksurface.Do NOT drive the machine to therepair area. Use a truck, or trailer, tomove the machine to the repairarea.
NOTE:Dependant on the "stop fault" conditionwhich exists and has been detected bythe computer controller, limitedoperation may be restricted to eitherforward, or reverse, direction of travel.If travel is not achieved in one direction,attempt to travel in the oppositedirection.
-
8/10/2019 Hypac C766C, C778B - om.pdf
62/122
Section 3OPERATION
3-24 7/00
VIBE MODE - FRNT/FDW
Fault: 5V SENSOR POWER
VIBE MODE - REAR/REV
Fault: 5V SENSOR POWER
LIMD OP: MODE - FNR FDW
Fault: 5V SENSOR POWER
AUTO
DRUM SELECT
AMPLITUDE
HIGH LOW
FRONT REAR
VIBRATOR MODE