Teller-Ulam design Hydrogen BombThe Teller–Ulam design is a nuclear weapon design which is used in megaton-range thermonuclear weapons, and is more colloquially referred to as "the secret of the hydrogen bomb". It is named after two of its chief contributors, Hungarian born physicist Edward Teller and Polish born mathematician Stanisław Ulam, who developed the design in 1951. The idea is generally thought to pertain specifically to the use of a fission bomb "trigger" placed near an amount of fusion fuel, known as "staging", and the use of "radiation implosion" to compress the fusion fuel before igniting it. There are a number of other additions and variations to this idea posited by different sources.

The basics of the Teller–Ulam configuration: a fission bomb uses radiation to compress and heat a separate section of fusion fuel.

The first device to be based on this principle was detonated by the United States in the "Ivy Mike" nuclear test in 1952. In the Soviet Union, this design was known as Andrei Sakharov's "Third Idea". Similar devices were developed by the United Kingdom, France, China, and Israel, though no specific codenames are known for their designs.

Public body of knowledge concerning nuclear weapon design

Detailed knowledge of actual fission and fusion weapons is classified to some degree in virtually every industrialized nation. In the United States, such "knowledge" can by

default be classified as Restricted Data even if it is created by persons who are not government employees or associated with weapons programs, in a legal doctrine known as "born secret" (though the constitutional standing of the doctrine has been at times called into question, see United States v. The Progressive, et al.). Born-secret is rarely invoked for cases of private speculation. The official policy of the United States Department of Energy has been not to acknowledge the leaking of design information, as such acknowledgement would potentially validate the information as accurate. In a small number of prior cases, though (see prior restraint), the U.S. government has attempted to censor weapons information in the public press, with limited success.

Though large quantities of vague data have been officially released, and larger quantities of vague data have been unofficially leaked by ex-bomb designers, most public descriptions of nuclear weapon design details rely to some degree on speculation, reverse engineering from known information, or comparison with similar fields of physics (inertial confinement fusion is the primary example). Such processes have resulted in a body of unclassified knowledge about nuclear bombs which is generally consistent with official unclassified information releases, related physics, and is thought to be internally consistent, though there are some points of interpretation which are still considered open. The state of public knowledge about the Teller–Ulam design has been most reliably shaped from a few specific incidences outlined in a section below.

Basic principle

The basic principle of the Teller–Ulam configuration is based upon the idea that different parts of a thermonuclear weapon can be chained together in "stages" which allow for the full detonation of each. At a bare minimum, this implies a primary section which consists of a fission bomb (a "trigger"), and a secondary section which consists of fusion fuel. Because of the staged design, it is thought that a tertiary section, again of fusion fuel, could be added as well, based on the same principle of the secondary. The energy released by the primary compresses the secondary through the concept of "radiation implosion", at which point it is heated and undergoes nuclear fusion.

One possible version of the Teller–Ulam configuration.

Surrounding the other components is a hohlraum or radiation case, a container which traps the first stage or primary's energy inside temporarily. The outside of this radiation case, which is also normally the outside casing of the bomb, is the only direct visual evidence publicly available of any thermonuclear bomb component's configuration. Numerous photographs of various thermonuclear bomb exteriors have been declassified.

The primary is thought to be a standard implosion method fission bomb, though likely with a core boosted by small amounts of fusion fuel for extra efficiency; the fusion fuel releases excess neutrons when heated and compressed, inducing additional fission. Generally, an entity with the capacity to create a thermonuclear bomb has already mastered the ability to engineer boosted fission. When fired, the plutonium-239 (Pu-239) and/or uranium-235 (U-235) core would be compressed to a smaller sphere by special layers of conventional high explosives arranged around it in a lens pattern, initiating the nuclear chain reaction that powers the conventional "atomic bomb".

The secondary is usually shown as a column of fusion fuel and other components wrapped in many layers. Around the column is first a "pusher-tamper", a heavy layer of unenriched uranium-238 (U-238) or lead which serves to help compress the fusion fuel (and, in the case of uranium, may eventually undergo fission itself). Inside this is the fusion fuel itself, usually a form of lithium deuteride, which is used because it is easier to weaponize than liquified tritium/deuterium gas (see Ivy Mike experiment). This dry fuel, when bombarded by neutrons, produces tritium, a heavy isotope of hydrogen which can undergo nuclear fusion, along with the deuterium present in the mixture. (See the article on nuclear fusion for a more detailed technical discussion of fusion reactions.) Inside the layer of fuel is the "spark plug", a hollow column of fissile material (plutonium-239 or uranium-235) which, when compressed, can itself undergo nuclear fission (because of the shape, it is not a critical mass without compression). The tertiary, if one is present, would be set below the secondary and probably be made up of the same materials.

A more simplified explanation of the above would be as follows:

1. An implosion assembly type of fission bomb is exploded. This is the primary stage. If a small amount of tritium gas is placed near the primary explosion, it will be compressed and a fusion reaction will occur; the released neutrons from this fusion reaction will induce further fission in the plutonium-239 or uranium-235 used in the primary stage. The use of fusion fuel to enhance the efficiency of a fission reaction is called boosting. Without boosting, a large portion of the fissile material will remain unreacted; the Little Boy and Fat Man bombs had an efficiency of only 1.4% and 14%, respectively, because they were unboosted.

2. Energy released in the primary stage is transferred to the secondary (or fusion) stage. The exact mechanism whereby this happens is unknown (see speculation regarding this below). This energy heats and compresses the fusion fuel, which is necessary to induce fusion; the fusion reaction releases neutrons as a product. Generally, increasing the kinetic energy of gas molecules contained in a limited volume will increase both temperature and pressure (see gas laws).

3. The fusion fuel of the secondary stage may be surrounded by depleted uranium, which is normally completely stable and atomically unreactive. However, when bombarded by the neutrons released in the secondary stage, the U-238 atoms begin splitting and undergo a fission reaction.

Actual designs of thermonuclear weapons may vary. For example, they may or may not use a boosted primary stage, use different types of fusion fuel, and may surround the fusion fuel with beryllium (or another neutron reflecting material) instead of depleted uranium to prevent further fission from occurring.

The basic idea of the Teller–Ulam configuration is that each "stage" would undergo fission or fusion (or both) and release energy, much of which would be transferred to another stage to trigger it. How exactly the energy is "transported" from the primary to the secondary has been the subject of some disagreement, but is thought to be transmitted through the x-rays which are emitted from the fissioning primary. This energy is then used to compress the secondary. There are five proposed theories:

Neutron pressure from the primary explosion. This was allegedly Ulam's first concept and was abandoned as unworkable.

Blast wave from the primary explosion. This was allegedly Ulam's second concept and was abandoned as unworkable.

Radiation pressure exerted by the x-rays. This was the first idea put forth by Howard Morland in the article in The Progressive.

X-rays creating a plasma in the radiation case's filler (a polystyrene plastic foam). This was a second idea put forwards by Chuck Hansen and later by Howard Morland.

Tamper/Pusher ablation. This is currently believed to be the actual mechanism.

Radiation pressure

The radiation pressure exerted by the large quantity of x-ray photons inside the closed casing might be enough to compress the secondary. For two thermonuclear bombs for which the general size and primary characteristics are well understood, the Ivy Mike test bomb and the modern W-80 cruise missile warhead variant of the W-61 design, the radiation pressure was calculated to be 73 million bar (atmospheres) (7.3 T Pa ) for the Ivy Mike design and 1,400 million bar (140 TPa) for the W-80

Foam plasma pressure

Foam plasma pressure is the concept which Chuck Hansen introduced during the Progressive case, based on research which located declassified documents listing special foams as liner components within the radiation case of thermonuclear weapons.

The sequence of firing the weapon (with the foam) would be as follows:

1. The high explosives surrounding the core of the primary fire, compressing the fissile material into a supercritical state and beginning the fission chain reaction.

2. The fissioning primary emits x-rays at the speed of light, which "reflect" along the inside of the casing, irradiating the polystyrene foam (see below for a note on what "reflection" means in this context).

3. The irradiated foam undergoes a phase transition, becoming a hot plasma, pushing against the tamper of the secondary, compressing it tightly, and beginning the fission reaction in the spark plug.

4. Pushed from both sides (from the primary and the spark plug), the lithium deuteride fuel is highly compressed and heated to thermonuclear temperatures, and begins a fusion reaction.

5. The fuel undergoing the fusion reaction emits a large flux of neutrons, which irradiates the uranium-238 tamper (or the uranium-238 bomb casing), begins to itself undergo a fission reaction, providing about half of the total energy.

This would complete the fission-fusion-fission sequence. Fusion, unlike fission, is relatively "clean"—it releases energy but no harmful radioactive products or large amounts of nuclear fallout. The fission reactions though, especially the last fission reaction, release a tremendous amount of fission products and fallout. If the last fission stage is omitted, by replacing the uranium tamper with one made of lead, for example, the overall explosive force is reduced by approximately half but the amount of fallout is relatively low.

Current technical criticisms of the foam plasma pressure focus on unclassified analysis from similar high energy physics fields which indicate that the pressure produced by such a plasma would only be a small multiplier of the basic photon pressure within the radiation case, and that the foam materials intrinsically have a very low absorption efficiency of the gamma and x-ray radiation from the primary. Most of the energy produced would be absorbed by the walls of the radiation case, and the tamper around the secondary. Analyzing the effects of that absorbed energy led to the third mechanism: ablation.

Tamper-pusher ablation

The third proposed mechanism is that the primary compression mechanism for the thermonuclear secondary is that the outer layers of the tamper-pusher, or heavy metal casing around the thermonuclear fuel, are heated so much by the x-ray flux from the primary that they ablate away, exploding outwards at such high speed that the rest of the tamper recoils inwards at a tremendous velocity, crushing the fusion fuel and the spark plug.

The sequence depicted is:

1. Bomb before detonation. The nested spheres at the top are the fission primary; the cylinders below are the fusion secondary device.

2. Fission primary's explosives have detonated and collapsed the primary's fissile pit.3. The primary's fission reaction has run to completion, and the primary is now at

several million degrees and radiating gamma and hard x-rays, heating up the inside of the hohlraum (radiation case) and the shield and secondary's tamper.

4. The primary's reaction is over and it has expanded. The surface of the pusher for the secondary is now so hot that it is also ablating or expanding away, pushing the rest of the secondary (tamper, fusion fuel, and fissile spark plug) inwards. The spark plug starts to fission. Not depicted: the radiation case is also ablating and expanding outwards (omitted for clarity of diagram).

5. The secondary's fuel has started the fusion reaction and shortly will burn up, and then blow the remaining components of the bomb apart.

Rough calculations for the basic ablation effect are relatively simple: the energy from the primary is distributed evenly onto all of the surfaces within the outer radiation case, with the components coming to a thermal equilibrium, and the effects of that thermal energy are then analyzed. The energy is mostly deposited within about one x-ray optical

thickness of the tamper/pusher outer surface, and the temperature of that layer can then be calculated. The velocity at which the surface then expands outwards is calculated and, from a basic Newtonian momentum balance, the velocity at which the rest of the tamper implodes inwards.

Applying the more detailed form of those calculations to the Ivy Mike device yields vaporized pusher gas expansion velocity of 290 kilometers per second and an implosion velocity of perhaps 400 kilometers per second if 3/4 of the total tamper/pusher mass is ablated off, the most energy efficient proportion. For the W-80 the gas expansion velocity is roughly 410 kilometers per second and the implosion velocity 570 kilometers per second. The pressure due to the ablating material is calculated to be 5.3 billion bar (530 T Pa ) in the Ivy Mike device and 64 billion bar (6.4 P Pa ) in the W-80 device.

Comparing the implosion mechanisms

Comparing the three mechanisms proposed, it can be seen that:

Radiation pressure: o Ivy Mike: 73 million bar (7.3 TPa)o W-80: 1.4 billion bar (140 TPa)

Plasma pressure: o Ivy Mike: (est.) 350 million bar (35 TPa)o W-80: (est.) 7.5 billion bar (750 TPa)

Ablation pressure: o Ivy Mike: 5.3 billion bar (530 TPa)o W-80: 64 billion bar (6400 TPa)

The calculated ablation pressure is one order of magnitude greater than the higher proposed plasma pressures and nearly two orders of magnitude greater than calculated radiation pressure. No mechanism to avoid the absorption of energy into the radiation case wall and the secondary tamper has been suggested, making ablation apparently unavoidable. The other mechanisms appear to be unneeded.

United States Department of Defense official declassification reports indicate that foamed plastic materials are or may be used in radiation case liners, and despite the low direct plasma pressure they may be of use in delaying the ablation until energy has distributed evenly and a sufficient fraction has reached the secondary's tamper/pusher.

Proposed design variations

A number of possible variations to the weapon design have been proposed:

Either the tamper or the casing have been proposed as being made of uranium-238 for the final fission stage.

In some descriptions, additional internal structures exist to protect the secondary from receiving excessive neutrons from the primary.

The inside of the casing may or may not be specially machined to "reflect" the x-rays. X-ray "reflection" is not like light reflecting off of a mirror, but rather the reflector material is heated by the x-rays, causing the material itself to emit x-rays, which then travel to the secondary.

Two special variations exist which will be discussed in a further section: the cryogenically cooled liquid deuterium device used for the Ivy Mike test, and the putative design of the W88 nuclear warhead — a small, MIRVed version of the Teller–Ulam configuration with a prolate (egg or watermelon shaped) primary and an elliptical secondary. Most bombs do not apparently have tertiary stages — the U.S. is only thought to have produced one such model, the massive 25 Mt B41 nuclear bomb, and the Soviet Union is thought to have used multiple stages in their 50 megaton Tsar Bomba. If any hydrogen bombs have been made from configurations other than those based on the Teller–Ulam design, the fact of it is not publicly known, with the possible exception of the Sloika design discussed below.

In essence, the Teller–Ulam configuration relies on at least two instances of implosion occurring: first, the conventional (chemical) explosives in the primary would compress the fissile core, resulting in a fission explosion many times more powerful than that which chemical explosives could achieve alone. Second, the radiation from the fissioning of the primary would be used to compress and ignite the secondary, resulting in a fusion explosion many times more powerful than the fission explosion alone. This chain of compression could then be continued with an arbitrary number of secondaries, and would end with the fissioning of the natural uranium tamper, something which could not normally be achieved without the neutron flux provided by the fusion reactions in the secondary. Such a design can be scaled up to an arbitrary strength, potentially to the level of a doomsday device, though usually such weapons are not more than a dozen megatons, which is generally considered enough to destroy even the largest practical targets.

HistoryMain History of the Teller–Ulam design

Original "Super"

The idea of a thermonuclear fusion bomb ignited by a smaller fission bomb was first proposed by Enrico Fermi to his colleague Edward Teller in 1941 at the start of what would become the Manhattan project. Teller spent most of the Manhattan Project attempting to figure out how to make the design work, to some degree neglecting his assigned work on the Manhattan Project fission bomb program. His difficult and devil's advocate attitude in discussions led Oppenheimer to sidetrack him and other "problem" physicists into the super program to smooth his way.

Credit controversy

Stanisław Ulam, a coworker of Teller's, made the first key conceptual leaps towards a workable fusion design. Ulam's two innovations which rendered the fusion bomb

practical were that compression of the thermonuclear fuel before extreme heating was a practical path towards the conditions needed for fusion, and the idea of staging or placing a separate thermonuclear component outside a fission primary component, and somehow using the primary to compress the secondary. Teller then realized that the gamma and X-ray radiation produced in the primary could transfer enough energy into the secondary to create a successful implosion and fusion burn, if the whole assembly was wrapped in a hohlraum or radiation case. Teller and his various proponents and detractors later disputed the degree to which Ulam had contributed to the theories underlying this mechanism.

Testing

The "George" shot of Operation Greenhouse in 1951 tested the basic concept for the first time on a very small scale, raising expectations to a near certainty that the concept would work.

In November 1, 1952, the Teller–Ulam configuration was tested at full scale in the "Ivy Mike" shot at an island in the Enewetak atoll, with a yield of 10.4 megatons (over 450 times more powerful than the bomb dropped on Nagasaki during World War II). The device, dubbed the Sausage, used an extra-large fission bomb as a "trigger" and liquid deuterium—kept in its liquid state by 20 short tons (18 metric tons) of cryogenic equipment—as its fusion fuel, and weighed around 80 short tons (70 metric tons) altogether.

A photograph of Operation Castle thermonuclear test, Castle Romeo shot.

The liquid deuterium fuel of Ivy Mike was impractical for a deployable weapon, and the next advance was to use a solid lithium deuteride fusion fuel instead. In 1954 this was tested in the "Castle Bravo" shot (the device was code-named the Shrimp), which worked far better (2.5 times) than expected and yielded 15 megatons, the largest U.S. bomb ever tested.

Efforts in the United States soon shifted towards developing miniaturized Teller–Ulam weapons which could easily outfit Intercontinental Ballistic Missiles and Submarine

Launched Ballistic Missiles. By 1960, with the W47 warhead deployed on Polaris submarines, megaton-class warheads were as small as 18 inches (0.5 m) in diameter and around 700 pounds (320 kg) in weight. Further innovation in miniaturizing warheads was accomplished by the mid-1970s, when versions of the Teller–Ulam design were created which could fit ten or more warheads on the end of a small MIRVed missile (see the section on the W88 below).

Soviet developments

The first Soviet fusion design, developed by Andrei Sakharov and Vitaly Ginzburg in 1949 (before the Soviets had a working fission bomb), was dubbed the Sloika, after a Russian layer cake, and was not of the Teller–Ulam configuration. It used alternating layers of fissile material and lithium deuteride fusion fuel spiked with tritium (this was later dubbed Sakharov's "First Idea"). Though nuclear fusion was technically achieved, it did not have the scaling property of a "staged" weapon. The fusion layer wrapped around the fission core could only moderately multiply the fission energy (modern Teller–Ulam designs can multiply it 30-fold). Additionally, the whole fusion stage had to be imploded by conventional explosives, along with the fission core, multiplying the bulk of chemical explosives needed substantially.

Their first Sloika design test, Joe-4, was detonated in 1953 with a yield equivalent to 400 kilotons of TNT (only 15%–20% from fusion).

The Tsar Bomba was a massive bomb developed by the Soviet Union, and demonstrated how the concept of "staging" could be used to develop arbitrarily powerful weapons.

Attempts to use a Sloika design to achieve megaton-range results proved unfeasible. After the U.S. tested the "Ivy Mike" device in 1952, proving that a multimegaton bomb could be created, the Soviets searched for an additional design. The "Second Idea", as Sakharov referred to it in his memoirs, was a previous proposal by Ginzburg in November 1948 to use lithium deuteride in the bomb, which would, in the course of being bombarded by neutrons, produce tritium. In late 1953 physicist Viktor Davidenko achieved the first breakthrough, that of keeping the primary and secondary parts of the bombs in separate pieces ("staging"). The next breakthrough was discovered and developed by Sakharov and Yakov Zel'dovich, that of using the X-rays from the fission bomb to compress the secondary before fusion ("radiation implosion"), in the spring of 1954. Sakharov's "Third Idea", as the Teller–Ulam design was known in the USSR, was tested in the shot "RDS-37" in November 1955 with a yield of 1.6 Mt.

The Soviets demonstrated the power of the "staging" concept in October 1961, when they detonated the massive and unwieldy Tsar Bomba, a 50 Mt hydrogen bomb which derived almost 97% of its energy from fusion. It was the largest nuclear weapon developed and tested by any country, but was far too large for the Soviets to use as a weapon.

British developments

In 1954 work began at Aldermaston to develop the British fusion bomb, with Sir William Penny in charge of the project. British knowledge on how to make a thermonuclear fusion bomb was rudimentary, and at the time the United States was not exchanging any nuclear knowledge because of the Atomic Energy Act of 1946. However, the British were allowed to observe the American Castle tests and used sampling aircraft in the mushroom clouds, providing them with clear, direct evidence of the high compression produced in the secondary stages by radiation implosion.

Because of these difficulties, in 1955 British prime minister Anthony Eden agreed to a secret plan, whereby if the Aldermaston scientists failed or were greatly delayed in developing the fusion bomb, it would be replaced by an extremely large fission bomb.

In 1957 the Operation Grapple tests were carried out. The first test, Green Granite was a prototype fusion bomb, but failed to produce equivalent yields compared to the Americans and Soviets, only achieving approximately 300 kilotons. The second test Orange Herald was the modified fission bomb and produced 700 kilotons—making it the largest fission explosion ever. At the time almost everyone (including the pilots of the plane that dropped it) thought that this was a fusion bomb. This bomb was put into service in 1958. A second prototype fusion bomb Purple Granite was used in the third test, but only produced approximately 150 kilotons.

A second set of tests was scheduled, with testing recommencing in September 1957. The first test was based on a "… new simpler design. A two stage thermonuclear bomb which had a much more powerful trigger". This test Grapple X Round C was exploded on November 8 and yielded approximately 1.8 megatons. Two final air burst tests on September 2 and September 11, 1958, dropped bombs that yielded almost 3 megatons—Britain's most powerful tests.

American observers had been invited to this second set of tests. After their successful detonation of a megaton-range device (and thus demonstrating their practical understanding of the Teller–Ulam design "secret"), the United States agreed to exchange some of their nuclear designs with Great Britain, leading to the 1958 US-UK Mutual Defence Agreement. Instead of continuing with their own design, the British were given access to the design of the smaller American Mk 28 warhead and were able to manufacture copies.

Other countries

The People's Republic of China developed their first Teller–Ulam device only 32 months after their first fission test, the shortest fission-to-fusion development time yet known.

The details of the development of the Teller–Ulam design in other countries are less well known. The People's Republic of China detonated its first device using a Teller–Ulam design June 1967 ("Test No. 6"), a mere 32 months after detonating its first fission weapon (the shortest fission-to-fusion development yet known), with a yield of 3.3 Mt. Little is known about the Chinese thermonuclear program, however. Very little is known about the French development of the Teller–Ulam design beyond the fact that they detonated a 2.6 Mt device in the "Canopus" test in August 1968. In 1998 India claimed to detonate a "hydrogen bomb" in its Operation Shakti tests ("Shakti I", specifically), though seismographic readings have led many non-Indian experts to conclude that this is unlikely, or at least it was unlikely to have been a success as claimed, because of its low yield (claimed to be around 45 kt, though outside experts estimate it at around 30 kt, both extremely low for a successful thermonuclear detonation). However, even low-yield tests can have a bearing on thermonuclear capability, as they can provide information on the behavior of primaries without the full ignition of secondaries.[

Public knowledge

The Teller–Ulam design was for many years considered one of the top nuclear secrets, and even today it is not discussed in any detail by official publications with origins "behind the fence" of classification. United States Department of Energy (DOE) policy has been, and continues to be, that they do not acknowledge when "leaks" occur, because doing so would acknowledge the accuracy of the supposed leaked information.

Photographs of warhead casings, such as this one of the W80 nuclear warhead, allow for some speculation as to the relative size and shapes of the primaries and secondaries in U.S. thermonuclear weapons.

Aside from images of the warhead casing (but never of the "physics package" itself), most information in the public domain about this design is regulated to a few terse statements by the DOE and the work of a few individual investigators.

Below is a short discussion of the events which lead to the formation of these "public" models of the Teller–Ulam design, with some discussions as to their differences and disagreements with those principles outlined above.

DOE statements

In 1972 the DOE declassified a statement that "The fact that in thermonuclear (TN) weapons, a fission 'primary' is used to trigger a TN reaction in thermonuclear fuel referred to as a 'secondary'", and in 1979 added, "The fact that, in thermonuclear weapons, radiation from a fission explosive can be contained and used to transfer energy to compress and ignite a physically separate component containing thermonuclear fuel." To this latter sentence they specified that "Any elaboration of this statement will be classified." The only statement which may pertain to the spark plug was declassified in 1991: "Fact that fissile and/or fissionable materials are present in some secondaries, material unidentified, location unspecified, use unspecified, and weapons undesignated." In 1998 the DOE declassified the statement that "The fact that materials may be present in channels and the term 'channel filler,' with no elaboration", which may refer to the polystyrene foam (or an analogous substance).

Whether these statements vindicate some or all of the models presented above is up for interpretation, and official U.S. government releases about the technical details of nuclear weapons have been purposely equivocating in the past (see, i.e., Smyth Report). Other information, such as the types of fuel used in some of the early weapons, has been declassified, though of course precise technical information has not been.

The Progressive case

Most of what is known today in the public domain about the Teller–Ulam design comes from a 1979 article in a left-wing magazine. This edition is available online.

Most of the current ideas on the workings of the Teller–Ulam design came into public awareness after the DOE attempted to censor a magazine article by U.S. antiweapons activist Howard Morland in 1979 on the "secret of the hydrogen bomb". In 1978 Morland had decided that discovering and exposing this "last remaining secret" would focus attention onto the arms race and allow citizens to feel empowered to question official statements on the importance of nuclear weapons and nuclear secrecy. Most of Morland's ideas about how the weapon worked were compiled from highly accessible sources—the drawings which most inspired his approach came from none other than the Encyclopedia Americana. Morland also interviewed (often informally) many former Los Alamos scientists (including Teller and Ulam, though neither gave him any useful information), and used a variety of interpersonal strategies to encourage informational responses from them (i.e., asking questions such as "Do they still use spark plugs?" even if he was not aware what the latter term specifically referred to).

Morland eventually concluded that the "secret" was that the primary and secondary were kept separate and that radiation pressure from the primary compressed the secondary before igniting it. When an early draft of the article, to be published in The Progressive magazine, was sent to the DOE after falling into the hands of a professor who was opposed to Morland's goal, the DOE requested that the article not be published, and pressed for a temporary injunction. The DOE argued that Morland's information was (1) likely derived from classified sources, (2) if not derived from classified sources, itself counted as "secret" information under the "born secret" clause of the 1954 Atomic Energy Act, and (3) was dangerous and would encourage nuclear proliferation.

Morland and his lawyers disagreed on all points, but the injunction was granted, as the judge in the case felt that it was safer to grant the injunction and allow Morland, et al., to appeal, which they did in United States v. The Progressive, et al. (1979).

Through a variety of more complicated circumstances, the DOE case began to wane as it became clear that some of the data they were attempting to claim as "secret" had been published in a students' encyclopedia a few years earlier. After another H-bomb speculator, Chuck Hansen, had his own ideas about the "secret" (quite different from Morland's) published in a Wisconsin newspaper, the DOE claimed The Progressive case was moot, dropped their suit and allowed the magazine to publish, which it did in November 1979. Morland had by then, however, changed his opinion of how the bomb worked, suggesting that a foam medium (the polystyrene) rather than radiation pressure was used to compress the secondary, and that in the secondary was a spark plug of fissile material as well. He published these changes, based in part on the proceedings of the appeals trial, as a short erratum in The Progressive a month later.[ In 1981 Morland published a book about his experience, describing in detail the train of thought which led him to his conclusions about the "secret".

Because the DOE sought to censor Morland's work — one of the few times they violated their usual approach of not acknowledging "secret" material which had been released — it is interpreted as being at least partially correct, though to what degree it lacks information or has incorrect information is not known with any great confidence. The difficulty which a number of nations had in developing the Teller–Ulam design (even when they apparently understood the design, such as with the United Kingdom), makes it somewhat unlikely that this simple information alone is what provides the ability to manufacture thermonuclear weapons. Nevertheless, the ideas put forward by Morland in 1979 have been the basis for all current speculation on the Teller–Ulam design.

Variations

There have been a few variations of the Teller–Ulam design suggested by sources claiming to have information from inside of the fence of classification. Whether these are simply different versions of the Teller–Ulam design, or should be understood as contradicting the above descriptions, is up for interpretation.

Richard Rhodes' "Ivy Mike" device in Dark Sun

In his 1995 book Dark Sun: The Making of the Hydrogen Bomb, author Richard Rhodes describes in detail the internal components of the "Ivy Mike" Sausage device, based on information obtained from extensive interviews with the scientists and engineers who assembled it. According to Rhodes, though there was polystyrene in the "Mike" device, it was not used as a plasma source — the radiation from the primary itself was enough to compress the secondary. Whether or not this would apply only to the "Mike" device, or the Teller–Ulam design in general, is not known, and potentially casts some doubt onto the role of the foam, and to the exact mechanism of radiation "transport".

W88 revelations

In 1999, information came out implying that in some U.S. designs, the primary (top) is prolate, while the secondary (bottom) is spherical.

In 1999 a reporter for the San Jose Mercury News reported that the U.S. W88 nuclear warhead, a small MIRVed warhead used on the Trident II SLBM, had a prolate (egg or watermelon shaped) primary (code-named Komodo) and a spherical secondary (code-named Cursa) inside a specially shaped radiation case (known as the "peanut" for its shape). A story four months later in The New York Times by William Broad reported that in 1995, a supposed double agent from the People's Republic of China delivered information indicating that China knew these details about the W88 warhead as well, supposedly through espionage. (This line of investigation eventually resulted in the abortive trial of Wen Ho Lee.) If these stories are true, it would indicate a variation of the Teller–Ulam design which would allow for the miniaturization required for small MIRVed warheads.

The value of a prolate primary lies apparently in the fact that a MIRV warhead is limited by the diameter of the primary—if a prolate primary can be made to work properly, then the MIRV warhead can be made considerably smaller yet still deliver a high-yield explosion—a W88 warhead manages to yield up 475 kt with a physics package 1.75 m (69 in) long, with a maximum diameter of 0.55 m (22 in), and weighing probably less than 800 lb (360 kg). Smaller warheads can allow a nation to fit more of them onto a single missile, as well as improve in more basic flight properties such as speed, mileage, and range.

The calculations for a nonspherical primary are apparently orders of magnitude harder than for a spherical primary, which would likely be of interest to an existing nuclear power like the People's Republic of China (particularly as they no longer conduct nuclear testing, which would yield invaluable design information).

Courtesy- Wikipedia