Hydraulic Valve Spring Compressor
-
Upload
jimboy-s-lara -
Category
Documents
-
view
245 -
download
0
Transcript of Hydraulic Valve Spring Compressor
-
8/4/2019 Hydraulic Valve Spring Compressor
1/39
HYDRAULIC VALVE SPRING COMPRESSOR
A Technical Feasibility Study
A Thesis
Presented To
The Faculty of College of Technology
Zamboanga City State Polytechnic College
In Partial Fulfillment for the Degree
Bachelor of Science in Automotive Technology
BY
GILBERT C. DELA PEA
MANNY G. VALLEDOR
ERIC S. LARA
2008
Table of Content
-
8/4/2019 Hydraulic Valve Spring Compressor
2/39
TITLE PAGE.i
TABLE OF CONTENTii
LIST OF TABLESv
LIST OF FIGURES..vi
APPROVAL SHEET...vii
ABSTRACT....viii
ACKNOWLEDGEMENT....ix
DEDICATION.xi
Chapter I INTRODUCTION
Origin and Justification of the Study1
State of the Problem..2
Objective of the Study...3
Scope and Delimitation of the Study.3
Chapter II CONCEPTUAL FRAME WORK
Review of Related Study and Literature....4
Related Study.5
Related Literature..8
Conceptual Model11
Operation Definition of Key of the Study12
Other Technical Terms.13
Chapter III RESEARCH METHOLOGY
-
8/4/2019 Hydraulic Valve Spring Compressor
3/39
Development of the Project.14
Supplies and Materials.15
Tool and Equipment16
Construction and Procedure17
Try out and Revision...17
Construction Time Frame18
Supplies Material and Cost..19
Labor Cost20
Chapter IV DESCREPTION OF THE COMPLETE PROJECT
Features of the Project.....30
Parts, Functions and Interrelationships31
Parts and functions...32
Interrelationships..32
Capabilities...33
Limitation.34
Operation Procedure34
Maintenance.35
Data Gathering Instrument...35
Statistical Tool......35
Research Instrument.38
Statistical Treatment.39
Feature of the Hydraulic Valve Spring Compressor42
Chapter V SUMMARY, CONCLUSION AND RECOMENDATION
Summary..44
-
8/4/2019 Hydraulic Valve Spring Compressor
4/39
Conclusion and Recommendations..................................................45
Appendix A..46
Evaluation sheet...47
Expert Evaluation Rating.48
Bibliography.49
LIST OF TABLES
-
8/4/2019 Hydraulic Valve Spring Compressor
5/39
Table 1 Supplies, Materials and Cost...15
Table 2 Tool and Equipment16
Table 3 Work Activities and allotment18
Table 4 Labor Cost...19
Table 5 Source of and Cost per Source20
Table 6 Parts of the Completed Project and their respective function.31
Table 7 Distribution of Respondent.....37
Table 8 Respondent Evaluation Results...41
LIST OF FIGURES
-
8/4/2019 Hydraulic Valve Spring Compressor
6/39
Figure 1 Conceptual Model..11
Figure 1 Perspective View...20
Figure 2 Measuring..21
Figure 3 Cutting Metal.21
Figure 4 Grinding.22
Figure 5 Cutting Plain Sheet....22
Figure 6 welding...23
Figure 7 Drill23
Figure 8 Body Filler.....24
Figure 9 Spray Gun..24
Figure 10 Rear View....25
Figure 11 Side View.26
Figure 12 Front View...27
Figure 13 Top View.28
-
8/4/2019 Hydraulic Valve Spring Compressor
7/39
Republic of the Philippines
ZAMBOANGA CITY STATE POLYTECHNIC COLLEGE
Region IX, Zamboanga Peninsula
R.T. Lim Blvd., Zamboanga City
Tel. No.993-0023
COLLEGE OF TECHNOLOGY
APPROVAL SHEET
IN PARTIAL FULLFILMENT of the requirements for the degree of Bachelor of Science in Automotive
Technology (BSAT) Curriculum, this Technical feasibility study entitled, Hydraulic valve spring
compressor: A Technical Feasibility Study, had been prepared and submitted by the IV-A Bachelor of
Science in Automotive Technology (BSAT) students, to wit:
1. GILBERT A. DELAPEA
2. MANNY O. VALLEDOR
3. ERIC S. LARA
Prof. ROSINI B. GRAGEDA MA.Ed Prof. BONNIE A. ANDABON MATVE
Other Adviser Adviser
Reader: Prof. RACHEL V. SEBASTIAN (MA)
APPROVED by the oral examination committee on: October 08, 2008 With the rating of PASSED.
Prof. FELIXBERTO B. PAGAYONAN MTE
Chairperson
-
8/4/2019 Hydraulic Valve Spring Compressor
8/39
Prof. BIRGILIO M. REBANTAD Prof. CARLOS L. LOLO MATVE
MEMBER MEMBER
ACCEPTED in partial fulfillment of the requirements for the degree of Bachelor of Science in Automotive
Technology (BSAT), Curriculum.
Prof. FELIXBERTO B. PAGAYONAN
Dean, College of Technology
ABSTRACT
The major purpose of the feasibility study was to develop the Hydraulic Valve Spring Compressor to be
used to remove the valve spring assembly. Otherwise, this gadget can use an instructional device in
teaching the module in removing the valve assembly of the Automotive Technology curriculum.
The developed gadget was subjected to the evaluation by the Automotive Technology instructors and
professors of Zamboanga City State Polytechnic College, Zamboanga City with a high and positive rating,
as an indicated in their strong agreement that the gadget had the potential capability of being effectivein removing the valve assembly.
The developed gadget is composed of structural assembly hydraulic jack, plain sheet, rivet, flat bar,
paint, bolt with nut, bearing and angle bar to assemble the Hydraulic Valve Spring Compressor.
It was recommended that a study should be conducted to determine the possibility of patenting and
mass production both for servicing and for instructional purposes. It was likewise recommended that
professors and instructors shall be encourage to work through their inventions of projects and other
instructional devices for the improvement and enrichment of the instruction.
-
8/4/2019 Hydraulic Valve Spring Compressor
9/39
ACKNOWLEDGEMENT
This study would not be realized without the unconditional and unending support of the people, whobacked us up from the start of this study up its completion.
The proponents warmly express their gratitude and thanks to the following;;
Mr. Virgilio M. Revantad their technical adviser, for the time given and share with the proponents in
expla9ijning and demonstrating the gadgets in front of the evaluator and helping the proponents make
through in the defense of the title of the feasibility study.
Miss Rosini B. Grageda, their other adviser, for her effort in helping the proponents finished their write
ups and helping with the statistical treatment of the study. Even if she was busy with her own
responsibilities, she graciously shared her time and energy.
Mrs. Rachel V. Sebastian, for her unselfish support and assistance in the editing of our paper. She was
indeed patient enough considering the proponents humble writings.
Mr. Bonnie A. Andabon, the chairman of the member of the panel, for the encouragement and valuable
help in the completion of this feasibility study and the patience in checking the contents of the study.
To the other members of the panel; Mr. Felixberto B. Pagayonan, Dean of the College of Technology
(COT) and Mr. Carlos C. Lolo, Head of COT.
To the proponents parents, for the love, care, understanding and support especially the financialassistance needed to buy the materials for the realization of the feasibility study.
Above all, the Almighty God, for the wisdom, guidance, and assurance that whatever comes along the
proponents way, He will always make them get through it.
Finally, warm thanks and appreciation are given all who in their own way helped make the study be
realized.
Chapter I
INTRODUCTION
-
8/4/2019 Hydraulic Valve Spring Compressor
10/39
Origin and Justification of the Study
Automotive service requires a variety of great job. The work performed must meet the needs of
the costumers, time, money and effort. Workings in the commercial automotive shop or automotive
service centers need tools and equipment that are very useful. The traditional work in the automotive
shop can find difficulty in accomplishing tasks in specified time because of lack of shop tools and
equipment and it can even cause accidents. The availability of some shop tools and equipment is rarely
found in the shop area because they are very expensive.
To answer one of these needs, the project proponents decided to design a Hydraulic Valve Spring
Remover, one which can solve the problem on cylinder head and valve servicing. The purpose of the
Hydraulic Valve Spring Remover is to remove the intake and exhaust valve spring assembly. However if
doing it manually, you need more strength in removing the valves of the cylinder head. This gadget does
not only to remove retainer locks of the valve, but it can be even be used to flatten bars if there are
irregularities in the bars. The operation of Hydraulic Valve Spring Compressor needs a long hand pump
lever, and it makes hydraulic valve spring moves downward to compress the intake and exhaust valve
and thereby the retainer lock is removed. This gadget is very useful in overhauling engines in automotive
shops and other service centers.
Statement of the Problem
This study attempted to develop an Improvised Hydraulic Valve Spring Compressor.
Specifically, it aim to answer the following questions:
1. What are the essential features of the Improvised Hydraulic Valve Spring Compressor in terms of
its:
a. Design
b. Component parts
c. Functions
2. Is the Improvised Hydraulic Valve Spring Compressor useful in servicing cylinder head?
3. How comparable is the Improvised Hydraulic Valve Spring Compressor to other valve spring
compressor terms of its:
a. Cost
b. Usefulness
-
8/4/2019 Hydraulic Valve Spring Compressor
11/39
c. Quality
Objectives of the Study
The objectives of the study are to:
a. Design and construct an Improvised Hydraulic Valve Spring Compressor.
b. Test the functionality of the Hydraulic Valve Spring Compressor. c.
Demonstrate the effectiveness of the Improvised Hydraulic
Valve Spring Compressor.
Scope and Delimitation of the Study
This technical feasibility study is centered on design, the constructions and testing of an Improvised
Hydraulic Valve Spring Compressor of the cylinder head of an automobile.
This project was tested and validated by selected automotive technician instructors and
professor of Zamboanga City Polytechnic College.
This project was conducted during the first semester of academic year 2008 2009.
Chapter II
-
8/4/2019 Hydraulic Valve Spring Compressor
12/39
CONCEPTUAL FRAMEWORK
This chapter covers the review of related studies and literature, presentation of conceptual model of
study, and operational definition of the key variables of study.
Review of Related Study and Literature
This review of the related study and literature consisted of several unpublished seminar papers,
automotive books and other reading materials to obtain relevant information. The review of these
aforementioned reading materials however, had not revealed any technical feasibility study conducted
by anyone that would in some way be similar to this technical feasibility study.
Related Studies The teaching of technology must be accompanied by laboratory works. It is only in the
laboratory work where students conceptualized the basic principles and operation of the technical jobs.
To bring about better products in vocational educational, laboratory activities should be given more
emphasis because it is in the laboratory where the students can clarify basic principles through actual
participation in the technical investigation designed to illustrate them. But the failure of the school to
provide better laboratory facilities, amperes the improvements of teaching technology. The need for
improvised apparatus made out of local materials will greatly uplift the deplorable condition tat most
vocational school now faced. As far as laboratory teaching is concerned, the curriculum demands
students involvement in the teaching leaning activities, which no doubt, will result to better
conceptualization and more meaningful leaning. So to facilitate earning and to have better activityoriented session in laboratory teaching, tools and equipment and apparatus are necessary.
A brief analysis of studies found related to the one being undertaken is reviewed below, the
ideas concepts, and principles cited give credence to the fact that improvisation of tools and apparatus
is a viable alternative in solving the problem of inadequacy of laboratory equipment.
It produced a very weird noise that disturbed the horses and so its usage was limited to a single street.
Richard made a claim that his invention had the power to carry near An example of improvisation in the
fabrication of equipment was the work of The academy of sciences of Albania its state that Hydraulics
was founded in 1957 as a part of Hydraulics Chair of the University of Tirana. The new Laboratory was
established in 1968 with a general area of 15000 sqm, from which 2000 sqm is covered area and 13000
sqm is opened area. Both laboratories have used mainly for experimental works by hydraulic modeling.
The water discharge of the New Laboratory for experimental When the Academy of Sciences was
founded in 1973; the New Laboratory Hydraulic Laboratory became one of its Institutions. The
fundamental task of this Laboratory was the study and solution of theoretical and experimental
problems of the hydraulic models for the constructing works in hydroenergetics, agriculture, transport,
industry, and municipal economy and water recourses in general.
-
8/4/2019 Hydraulic Valve Spring Compressor
13/39
The main duty of this Department is to carry out studies and research in the field of surface water by
analytical, numerical and physical modeling and studies in site with a local or regional nature, taking also
into consideration the different hydraulic structures, such as the bridges, dams, groynes and spur dikes,
coastal protection structures.
The main directions of this Department are:
1. Hydraulics of open channels and Rivers, which includes the studies and research activity for the
hydraulic regime of open channels (artificial and natural), especially for the rivers of our country. The
prediction of such parameters such as the water discharge, water velocity, water levels is very important
for the hydraulic regime of the flow in open channels and rivers.
2. Coastal Hydraulics, which includes the studies and research activity for the prediction of the
parameters of coastal waves, such as the length, height and period of them, on the bases of preliminary
data founded by the measurement in site, etc. Some other phenomena such as the refraction and
diffraction of the waves are also very important to be predicted by numerical or physical modeling. The
solution methods used have been by analytical calculation, numerical models and physical models.
3. Study of the hydraulic regime of the hydraulic structures, which includes the different hydraulic
structures in hydroenegetic and agricultural works, ports and harbors and the structures for river and
coastal bank protection. It is worthy to mention in these structures the different kind of the spillways
constructed in hydro energetic and agricultural works, the bridges constructed on the river beds, the
dams, groynes and dikes for river and coastal protection, breakdowns constructed in ports and harbors,
etc.
4. Transport of sediments in river beds and coastal sediments, by which are predicted by analytical
or measurements in site and by numerical methods the main parameters of the bed and suspendedsediment flow in rivers and Torrens or for the irrigation systems of agricultural lands.
Related Literature
According to Roberts and Freeman (1982: 55) technical innovation is supplemented and adapted
through a series of phases. Someone first has an idea. It is good; the idea goes to a technical problem
-
8/4/2019 Hydraulic Valve Spring Compressor
14/39
solving advancing to design and development. Finally, if it fills a significant social need; the new product
utilized and diffused throughout the market.
According to Richard Dudgeon (1851), he was granted a patent for hydraulic jack. In the year
1855, he literally amazed on lookers a New York when he drove from his abode to his place of work in a
steam carriage about to people on a single barrel anthracite coal at a speed of 14 m. p. h. dudgeondeserves a special credit for his innumerable inventions including the roller boiler tube expanders, filter
press jack, pulling jack, heavy plate hydraulic hole pushes and various kinds of lifting jacks.
To operate the hydraulic compress, pump the handle on the hydraulic cylinder up and down.
This increases the pressure of the ram. It In then exerts a much greater force against the part it is
touching. This force can straighten bent part or remove and install press-fit parts. These include bushing,
bearings brake-drum studs piston ring and rivets. The press can do many other jobs requiring a high and
steady force.
Joseph Bramah (1796) employed to shape, extrude, or stamp metals and to test materials under high
pressures. Units developing a force of more than 4 million kg (more than 9 million lb) have been
developed for shaping whole aircraft sections.
Hydraulic jack are widely used all across the globe. They have a lot of relevance in the present
area, as they have made an incredible contribution in making our life more comfortable than it was
before. These jacks have outweighed conventional screw jacks that were in use at some point of time.
Hydraulic jack basically consists of two cylinders joined together. It works on the principle of Pascals
Law which suggests that when there is an increase in pressure in any point in a container of fluid, there
is an equal increase in pressure at very other point in the container.
Use the valve spring compressor and removed the valves and spring from the head. Place the parts inorder in a rack. If valve cannot be pulled out of the valve guide by hand, check for a tip end that
mushroomed or peeve over. If this has happened, use a file or small grinding stone to slightly chamfer
the tip end. Forcing a valve though the guide will damage or break the guide.
During the design of equipment that requires fluid power, many factors are considered in selecting the
type of system to be used hydraulic, pneumatic, or a combination of the two. Some of the factors are
required speed and accuracy of operation, surrounding atmospheric conditions, economic conditions,
availability of replacement fluid, required pressure level, operating temperature range, contamination
possibilities, cost of transmission lines, limitations of the equipment, lubricity, safety to the operators,
and expected service life of the equipment.
Viscosity is one of the most important properties of hydraulic fluids. It is a measure of a fluids resistance
to flow. A liquid, such as gasoline, which flows easily, has a low viscosity; and a liquid, such as tar, which
flows slowly, has a high viscosity. The viscosity of a liquid is affected by changes in temperature and
pressure. As the temperature of a liquid increases, its viscosity decreases. That is, a liquid flows more
easily when it is hot than when it is cold. The viscosity of a liquid increases as the pressure on the liquid
increases.
-
8/4/2019 Hydraulic Valve Spring Compressor
15/39
A satisfactory liquid for a hydraulic system must be thick enough to give a good seal at pumps, motors,
valves, and so on. These components depend on close fits for creating and maintaining pressure. Any
internal leakage through these clearances results in loss of pressure, instantaneous control, and pump
efficiency. Leakage losses are greater with thinner liquids (low viscosity). A liquid that is too thin will also
allow rapid wearing of moving parts, or of parts that operate under heavy loads. On the other hand, if
the liquid is too thick (viscosity too high), the internal friction of the liquid will cause an increase in theliquids flow resistance through clearances of closely fitted parts, lines, and internal passages. This
results in pressure drops throughout the system, sluggish operation of the equipment, and an increase
in power consumption.
Conceptual Model
The conceptual model of this study which depicted in figure 1.
Figure1. Conceptual Model of the Study
This study followed the input-throughput-out put approach.
The input of study is alternatives ideas from related and literature, supplies in materials, tools inequipment, and labor.
The through put of the consisted of the process involved in the device such as; designing, constructing,
and testing. The output of this study is the completed improvised hydraulic valve spring compressor.
2. Operational Definition of terms Variables used in the Study
-
8/4/2019 Hydraulic Valve Spring Compressor
16/39
The key variables and their operational definition are as follows:
The Completed improvised Hydraulic valve spring compressor is the assembly of the unit which is
operational to be use by technician during laboratory works.
Hydraulic jack used to compress the valve remover in the cylinder
Flat bar used to put the cylinder head
Wheel used to move one place to another place
Cabinet used to keep the part and tools
Structural frame - used to valve train keeper
Chapter III
METHODOLOGY
Development of the Project
This chapter presents a brief description of the supplies and material tools, and equipment,
construction, procedure, try out and revision, construction time frame, and total cost of the project.
Supplies and Materials
Table I shows the quantity, unit and name and description of the supplies and materials necessary in the
construction of the project
Table 1
Supplies, Materials and Costs
Quantity Unit Name and description Unit cost (in php) Total cost (in php)
3 kl. Welding rod 95.00 285.00
1 Pc. G.I pipe s-40 30.00 30.00
-
8/4/2019 Hydraulic Valve Spring Compressor
17/39
1 qrt. Metal primer 80.00 80.00
1 Pc. P/brush 11/2 18.00 18.00
1 pc MS plate 0.20x0.40 300.00 300.00
1 Pc. Angle bar 1/4x2x2x6 939.00 939.00
1 Pc. G.I Plain sheet # 16 250.00 250.00
8 Pc. Bolt w/nut 5.00 40.00
4 Pc. Bearing 50.00 200.00
1 pc Hydraulic jack 2T 420.00 420.00
GRAND TOTAL 2,562.00
Tools and Equipment
Table 2 shows the tools and equipment used in the construction of the project and other
respective used.
Table 2
TOOLS AND EQUIPMENT AND THEIR RESPECTIVE FUNCTION
Tools and Equipment Uses and function
TOOLS
a. Hacksaw
Cutting the work piece to the desire size.
b. File Finishing and smoothing the surface of the parts to the fabricated.
c. Drill bit Drilling holes on the parts to be produce.
d. Try square Setting the parts to be jointed at 90 angle.
e. Pull-push rule Measuring dimensions of parts to be cut and manufactured.
f. Clipping hammer Removing slugs on the surface of the weld
g. Center punch Marking the parts of the metals to be drilled
h. Wrenches Tightening and loosening screws
-
8/4/2019 Hydraulic Valve Spring Compressor
18/39
l. Spray Gun Device used for applying liquid. A device that uses pressure to apply atomized paint or
other liquid.
EQUIPMENT
a. Welding Machine Joining the metal parts of the project by the process of fusion.
b. Drill press Making hole on the parts of the project.
c. Shaper Flattening and squaring the metal parts of the project.
d. Grinder Sharpening the tool bit and removing the unnecessary metal parts.
Construction Procedure
The Improvised Hydraulic Valve Spring Compressor is made up of the following:
Base Assembly
This assembly is made of a bar and metal plain sheet which is constructed into a base assembly
of Hydraulic Valve Spring Compressor.
The following are the procedures in constructing this assembly: Prepare the hydraulic jack, thinner paint,
body filler, and angle bar; flat bar and metal plain sheet, shaped the angle bar into a rectangular with
the length 50 inches and the width 17 inches. Hydraulic jack must assemble how to remove the valve
assembly. Measure the angle into equal length and wide. Then cut it in same measure. Then measure
also the plain sheet it make a drawer and cabinet. Then you need put it to the angle assembly using the
rivet. Weld each part correctly and accurately inspect and clean the angle bar, MS plate and plain sheet
that have been welded on each part. When assemble the Hydraulic Valve Spring Compressor you must
applying a body filler to level the curve. Then paint it using the spray gun assembly to finalize the HVSC.
Try out and Revision
On the assembly line of the major components of the project, fittings, defects and minor revisions were
noted, tested, and evaluated. The purpose of try out and revisions were mainly to identify and remedy
the defective parts and to improve its capability and functionality for greater accuracy.
Defects Revisions
1. The first defect was the failure of the hydraulic linkage. And is not functioning. First check the
gasket of the hydraulic press and its liquid.
-
8/4/2019 Hydraulic Valve Spring Compressor
19/39
E. Construction time frame
Table III shows the work flow of activities in series and the time allotment
Table 3
Work activities and the allotment
Work activities Time Allotment
(in hours)
1. Preparation and supplies and Materials 48
2. Bench works 24
3. Welding works 24
4. Painting job 48
5. Assembly works 8
6. Try-out and revision 36
Total number of hours 188 hours
As revealed in table III the project was constructed in the period of the one
hundred eighty-eight (188) hours which is equivalent to twenty working days.
Table 4
Labor cost
No. of workers Description Rate/day No. of days Total cost
1 Machinist 500.00 1 day 500.00
1 Welder 50.00 1 day 50.00
1 Painter 300.00 1 day 300.00
-
8/4/2019 Hydraulic Valve Spring Compressor
20/39
Total cost of labor 850.00
Table 5
Sources of cost and cost per source
Sources Cost(in Pph)
1. Supplies materials 2,562.00
2. Labor 850.00
3. Miscellaneous expenses 300.00
Total cost of production 3,012.00
Current cost commercial made hydraulic bulb spring compressor 9,000.00
Difference 5,088.00
The table shows the actual production cost of the project which amounted
Php 3,012.00
Figure 2. Dimensional Plan of HVSC
Figure 3. Measuring the metal plain sheet
Figure 4. Cutting the angle bar
Figure 5. Grinding the angle bar to remove unnecessary welds.
-
8/4/2019 Hydraulic Valve Spring Compressor
21/39
Figure 6. Cutting the plain sheet.
Figure 7. Welding the angle bar.
Figure 8. Drilling the structural assembly
Figure 9. Applying auto-body filler
Figure 10. Final painting of the HVSC
Figure 11. Fastening the bolts and nuts
Figure 12. Testing and operating the hydraulic jack
Figure 13. Removing the valve assembly.
Figure 14. Installing the spring.
Figure 15. Rear view of the HVSC
Figure 16. Side view of the HVSC
Figure 17. Front view of the HVSC
-
8/4/2019 Hydraulic Valve Spring Compressor
22/39
Figure18. Top view of the HVSC
Chapter IV
DESCRIPTION OF THE COMPLETED PROJECT
This chapter discusses the structure of the gadget and the several processes involved in its
operation, maintenance and control.
A. Structure
The improvised hydraulic valve spring compressor is modification of the commercially produced
hydraulic valve spring compressor. The modification lies in the substitution of most parts with locally
available materials.
The structure of the project includes the features, parts, and functions and theirinterrelationships, capabilities, and limitations.
1. Features of the project
The features of the project are enumerated and briefly discussed below:
A. Hydraulic jack
The hydraulic it will serve as to press the valve spring so that we can remove the lack of the valve
spring.
B. Hydraulic Manually Operated
The lever is pressed down to operate the mechanism, this fluid is trapped on the barrel creating
hydraulic pressure to test the opening pressure of the nozzle.
C. Can be produced locally
Since all materials used are available in the locality, then this gadget can be made locally with
the expertise of the instructors.
2. Parts, functions and Interrelationships
-
8/4/2019 Hydraulic Valve Spring Compressor
23/39
Table 8 reveals the major parts of the completed project and the corresponding functions of
each of these parts.
Table 6
Parts of the Completed Project and Their Respective Functions
1. Hydraulic Jack They compress with pressure inside the hydraulic jack to remove the four valve
assembly.
2. Cylinder head table Used for put the cylinder head assembly.
3. Valve spring drawer To keep all the valve and spring in the proper place into the drawer.
4. Cabinet When you work in this kind gadget they have put your cylinder into cabinet when off
time.
5. Wheel They move one place to another place.
Parts and Functions
The Hydraulic Valve Spring Compressor consists of the following parts.
a. bolts- used to hold adjustable tube holder
b. lock nuts- used to lock or fasten
c. Plain sheet- served as the body of the assembly
d. Rivet- used to lock the plain sheet into the angle bar.
e. Wheel- served to move one place to the other placed.
f. Drawer- Used to keep all the component parts of the cylinder assembly.
Interrelationship - the various parts of the project have a distinctive function which links the appropriate
operation of the Hydraulic Valve Spring Compressor. To achieve the best performance, each part should
function efficiently.
Hydraulic Jack.- It designed to push the heavy equipments. An Hydraulic lift, is a lift that works by using
hydraulic oil to raise and lower it, an hydraulic ram is fitted to the under side of the lift. Other lifts work
by means of the traction sheave driving the lift car up and down. An Hydraulic lift is not as fast as normal
lift, but can take greater weight, and the other thing about an Hydraulic lift is that the lift motor room
can be remote from the lift shaft unlike a normal lift. But in my research it reverses for using in order to
-
8/4/2019 Hydraulic Valve Spring Compressor
24/39
used the hydraulic jack. They used it removed the valve spring assembly to combine it two gadget
hydraulic jack and valve spring remover.
Cylinder head table-It can serve useful to put the cylinder head assembly. When the time you need to
remove the valve spring assembly.
Valve spring drawer and cabinet-When the time you remove the valve spring assembly you need one
place to put them in separated the valve spring into each piston. That why one of my gadget I needed to
put a drawer to separate it in order to put the valve assembly. Sometime we need a place to put the
some spare part of engine we put it a cabinet to safe it all the engine assembly.
Wheel-Some gadget has a wheel that moves it into another place when you need to put them. One of
my gadgets they have also a wheel to serve it into one place to another place.
3. Capabilities
The gadget can perform several activities during work shop time. it can served it to remove the
valve spring assembly.
The hydraulic valve spring compressor is to remove it all the valve spring assembly. Put the
cylinder head into the cylinder head table. Pump it the hydraulic jack with valve spring remover using
the long hand tube handle. Compress the valve spring in order to remove and Remove the valve lock by
using the magnet.
4. Limitation
This Hydraulic Valve Spring Compressor is used to pressed the valve spring assembly
Although this gadget is designed to removed the valve spring assembly. It cannot be
used to the power plant engine.
This Hydraulic Valve Spring Compressor is used only in automotive industry.
B. Process
This process includes operating procedures, maintenance and safety and control measures,
whereby the valve spring remover was connected the hydraulic jack.
Operating procedure
Precaution on handling hydraulic jack, it should be keep in mind of the lack in the hydraulic jack is
always close. In the removing the valve be sure we must used a proper tools in order to remove. When
we removed the other valve spring assembly is easy to point the other valve spring assembly.
-
8/4/2019 Hydraulic Valve Spring Compressor
25/39
Maintenance
The following steps help in extending the life span of the gadget.
When you put the cylinder head be sure in the proper position.
After removing the valve lock you need put in the proper place inside the drawer.
After working make to cleanup the hydraulic valve spring compressor.
Data-Gathering Instrument. A set of research instruments was constructed in the collection of data for
the present study. The Self-Administered Questionnaires was composed of two parts. Part I, contains
the variables on the personal profile of the instructors or respondents in the automotive industry in
Zamboanga City, who evaluated the effectiveness of the Improvised hydraulic valve spring compressor.
The variables included in personal profile are: Gender, Age, Educational Attainment,
Statistical Tool
The Respondent of the Study
The respondents of the study were the shop work laboratory instructors and professors of ZCSPC. There
were four (4) Automotive Technology Instructor and Professor while there were two (2) electrical
technology instructors and professors. Although the ACST was a gadget to be used for automotive
vehicles, the proponent deemed it necessary to included selected electrical technology instructors and
professors since the HVSC has automotive component in it.
Table 6. Show the distribution of the respondents. Of the five (5) respondents, there were four (4)
automotive technology instructor and professors which comprised sixty seven percent (67%) of the
number of respondents. Meanwhile, there were two (2) technician technology graduated of Zamboanga
State Polytechnic College comprised thirty three percent (33%) of the total number of the respondents.
There were two (2) instructors and professors respondents whose age range from 21-35 years old total
number of respondents. The age remaining four (4) range from 36-50 years old. Two (2) respondents
were all bachelors degree holder and only two (2) finished his master degree. One (1) respondent had a
working experience of two (2) years and below. Another one (1) also working experiences of one (1)
-
8/4/2019 Hydraulic Valve Spring Compressor
26/39
year. All these evaluator respondents were employed by Zamboanga City State Polytechnic College,
which is a public educational institution. All respondents were males.
Table 7
Distribution of Respondents
Respondents No. of Respondents Percentage
1. Instructors 4 67%
2. Technicians 2 33%
Total 6 100%
As shown in Table 7, four (4) instructors came from Zamboanga City State Polytechnic College (ZCSPC),
they were carefully selected to evaluate the effectiveness of the Improvised Wheel Alignment Machine.
One of the four (4) instructors is a graduate of Master of Arts in Teaching Vocational Education (MATVE)
major in Industrial Arts at the Zamboanga City State Polytechnic College, and had been teaching
automotive subjects in high school for 6 to 10 years. The other instructor has a unit of 36 academic
requirements in Master of Arts in Teaching Vocational Education (MATVE) major in Industrial Arts at the
Zamboanga City State Polytechnic College, and had been teaching Automotive Technology subject for
more than 21 years. The instructor is a graduate of Bachelor of Science in Marine Engineering (BS Mar-E)
, and had been teaching Power Plant Engineering and Automotive Technology subjects for more than 21
years. The other instructor is a graduate of Bachelor of Science in Industrial Education major in
Automotive at the Zamboanga City State Polytechnic College, and had been teaching automotive subject
for 2 years from WMSU and ZCSPC.
Research Instruments
-
8/4/2019 Hydraulic Valve Spring Compressor
27/39
We have only one set of research instrument constructed in the collection of data for the present study.
The Self-Administered Questionnaire. It was composed of two parts. In part I were contained the
variables on the personal profile of the instructors or respondents in the automotive industry in
Zamboanga City, who evaluated the effectiveness of the Hydraulic Valve Spring Compressor (HVSC). The
personal profile include those variables on: Gender; Age; Educational Attainment; Position; Employer;
Number of years in service; and name of office/establishment and office address.
Part II contained the items that purportedly measured the level of agreement among the respondents in
the automotive industry of Zamboanga City on the potential effectiveness of the HVSC. A three (3) point
scale was used in the qualitative description of the level of the respondents agreement.
Statistical treatment
A portion of this study necessitated the use of questionnaires in gathering pertinent data in determining
the effectiveness of the HVSC. In as much as the data for the effectiveness of the HVSC were collected
through the Experts Evaluation Rating (EERS) that utilized a three joint scale, it was necessary to convert
these scales through same equalizations. Hence,
Description Evaluation Rating
Strongly Agree(SA) 3
Agree (A) 2
Not Agree (NA) 1
Five (5) general topic areas were conducted in the data gathering instrument. These are the following:
1. The hydraulic valve spring compress or is easy to operate.
2. The hydraulic valve spring compressor functions effectively.
3. The hydraulic valve spring compressor can compress valve spring.
-
8/4/2019 Hydraulic Valve Spring Compressor
28/39
4. The component parts of hydraulic valve spring compressor are replaceable.
5. The hydraulic valve spring compressor can be use by any one.
Each of these five (5) topics was provided with items. There was a total of five items that covered the
topics in the Hydraulic Valve Spring Compressor (HVSC). A total of five (5) items in the distribution of the
respondents comprised of 100%. The items for evaluating the level of effectiveness of the HVSC which
comprised of 2.95% of allocated in the following: 1.) The hydraulic valve spring compress or is easy to
operate which comprised of 3.00% in the instructor respondents and 3.00% in the technician
respondents; 2.) The hydraulic valve spring compressor functions effectively which comprised of 3.00%
in the instructor respondents and 3.00% in the technician respondents; 3.) The hydraulic valve spring
compressor can compress valve spring which comprised of 3.00% in the instructor respondents and
3.00% in the technician respondents; 4.) The component parts of hydraulic valve spring compressor arereplaceable comprised of 3.00% in the instructor respondents and 3.00% in the technician respondents;
5.) The hydraulic valve spring compressor can be use by any one which comprised of 3.00% in the
instructor respondents and 3.00% in the technician respondents;.
Table 8
Respondents Evaluation Results
SA A NA X
4 - - 3.00
4 - - 3.00
4 _ - 3.00
4 - - 3.00
4 - - 3.00
-
8/4/2019 Hydraulic Valve Spring Compressor
29/39
Overall x= 3.00
Interpretation = Strongly Agree
Technicians SA A NA X
Question #1 2 - - 3.00
Question #2 2 - - 3.00
Question # 3 2 _ - 3.00
Question #4 2 - - 3.00
Question#5 2 _ _ 3.00
Overall x= 3.00
Interpretation = Strongly Agree
The weighted mean for this item is 2.81 which fall under the category Strongly Agree (SA).
An application that can be derived from this result is that the HVSC is to be an effective device in
removing the valve spring assembly.
Features of the Hydraulic Valve Spring Compressor
The first problem pursued in this study was stated as What are the features of the Hydraulic
Valve Spring Compressor is terms of its Design, Component parts and functions these were discussed as
the follows.
A. Design The features of the HVSC in terms of its design are on the interrelationships with the
corresponding functions.
B. Component part and their functions- The features of the HVSC in terms of its component parts are on
the construction procedures.
Comparability of the Hydraulic Valve Spring Compressor
Is the Hydraulic Valve Spring Compressor comparable to the other valve spring remover in terms
of cost, usefulness and quality? These were discussed below.
-
8/4/2019 Hydraulic Valve Spring Compressor
30/39
Cost- Based on the computation show in table 1, the total cost of the supplies and materials to complete
the production of one unit of the Hydraulic Valve Spring Compressor is 2562.00 pesos.
Usefulness- The Hydraulic Valve Spring Compressor is use only to removed the valve spring assembly,
while the other valve spring remover is using a force. But it gives same performance in terms of
removing the valve spring assembly.
Quality- In terms of the outputs of both removing the valve spring remover. The Hydraulic Valve Spring
Compressor have a little advantages, it can used to remove by using the hydraulic jack. But, Terms of
quality of the gadget. The Hydraulic Valve Spring Compressor in terms of its design and component
parts.
Four general topic areas were conducted in the data gathering instrument. These are the following;
1) The HVSP is installable.
2) The HVSP is functional.
3) The HVSP is safe to use.
4) The HVSP can be used for overhauling.
Chapter V
-
8/4/2019 Hydraulic Valve Spring Compressor
31/39
SUMMARY, CONCLUSION AND RECOMMENDATIONS
This chapter presents the summary, conclusion, and recommendations of the study.
Summary
This technical feasibility study was made possible to the need of automotive shop of ZCSPC especiallythe Hydraulic Valve Spring Compressor. This would help the students in hands on practice to develop
skills and knowledge when it comes to laboratory activities in vocational technical school or institutions.
This study whose primary objective was to design, constructs, and tests the functionality and
effectiveness of the Hydraulic Valve Spring Compressor. A Hydraulic Valve Spring Compressor is to be
used by instructors, professors, and students as a gadget in testing in removing and installed valve
spring assembly. Furthermore, this study enhances the students effectiveness in their working
performance.
The Hydraulic Valve Spring Compressor was developed to through the basic theoretical concept
of problems involving the overhauling in the automotive shop in Z.C.S.P.C. The conceptual idea of the
was purely of the re Hydraulic Valve Spring Compressor searcher.
Conclusion
The result of the study revealed that the production of Hydraulic Valve Spring Compressor is
feasible and that it can be designed and constructed by automotive instructors, teachers to overcome
the perennial problem of overhauling most especially in hands on laboratories activities.
Recommendations
Based on the conclusions of the study, the following recommendations are hereby proposed.
1. School administration should motivate and provide financial support to teachers, instructors,
and students in automotive technology of the Z.C.S.P.C. to unveil their unlimited ideas to improve and
provide laboratory equipments.
2. further research should be conducted on the feasibility of having;
3. Hydraulic Valve Spring Compressor can only be used within the hydraulic jack in 2ton.
-
8/4/2019 Hydraulic Valve Spring Compressor
32/39
APPENDIX A
Republic of the Philippines
Zamboanga City State Polytechnic College
Region IX, Zamboanga Peninsula
R.T. Lim Boulevard, Zamboanga City
Date:___________
Mr.________________
This College
Dear Sir:
Greetings of peace!
In view of the evaluation process of our Technical Feasibility Study on Hydraulic Valve Spring
Compressor, the proponents of this study humbly invite you to be one of our evaluators to evaluate
our project.
Your acceptance of this evaluation would help us in the completion of our project.
-
8/4/2019 Hydraulic Valve Spring Compressor
33/39
Thank you very much and more power.
Very truly yours,
GILBERT A. DELAPEA
Proponent
MANNY O. VALLEDOR
Proponent
ERIC S. LARA
Proponent
Noted by:
BONNIE A. ANDABON
Instructor
APPENDIX B
A SELF ADMINISTRATION QUESTIONAIRE ON THE EFFECTIVENESS OF THE HYDRUALIC VALVE SPRING
COMPRESSOR EVALUATED BY THE EXPERTS IN THE AUTOMOTIVE INDUSTRY
-
8/4/2019 Hydraulic Valve Spring Compressor
34/39
A. Personal Data
Directions: please put a check mark, or whatever it is necessary, write the request data on the blank
space provided.
Name :( Optional)_____________________Sex :_________( Male)_________(Female)
Age :_______( 20 yrs old below)_______(21 to 35 yrs old)________(36 to 50 yrs old)_____(50 years old
above)
Highest education attainment:
____(Doctorate);______(Masters Degree);______(Bachelors Degree);
____(Vocational)
____(Others). Please Specify
Position:
____(Professor);_____(Instructor);_____(Specialist);_______(Technicians) ______(Others). Please
Specify
Employer:
___(Public Education Institution);_____(Private Education Institution);
___(Government Owned Corporation);____( Private Owned Corporation);
___(Others). Please Specify
Number of years in the service:
___(5 yrs and below)____(6 to 10 yrs);____(11 to 15 yrs);____(16 to 20 yrs);
___(21 yrs and above)
Name of office/establishment and office address:
______________________________________________________________________
-
8/4/2019 Hydraulic Valve Spring Compressor
35/39
APPENDIX C
EXPERT EVALUATION RATINGS ON THE EFFECTIVENESS OF THE HYDRUALIC VALVE SPRING COMRESSOR
Directions: below are the statements that describe how effective the hydraulic valve spring compressor.Please put a check mark on the space that correspondent to your honest evaluation using the rating
scale below:
Descriptive Evaluation Descriptive Rating Strongly agree (SA)
3
Agree (A) 2
Not Agree (NA) 1
ITEM SA A NA X
1. The hydraulic valve spring compress or is easy to operate.
2. The hydraulic valve spring compressor functions effectively.
3. The hydraulic valve spring compressor can compress valve spring.
4. The component parts of hydraulic valve spring compressor are replaceable.
5. The hydraulic valve spring compressor can be use by any one.
APPENDIX D
BIBLIOGRAPHY
Books
Crouse, William H. and Anglin, Donald L. Automotive Mechanics, 10th
edition McGraw- Hill Company, 1994.
Fancisco, Felizardo Y. and Molina, Orvil M. Basic Automotive Electricity
National Bookstore, 1992.
Gregorys Scientific Publications Service and Repair Manual, Magna TR
Series Four Cylinder, Gregorys 1993.
Stockel, Martin W. and Stockel Martin T. Auto Service Repair
-
8/4/2019 Hydraulic Valve Spring Compressor
36/39
GOODHEART- WILLCOX COMPANY, INC 1984.
Unpublished Materials
Amor, Eli R. Development and Multi Electric Device (Unpublished
Seminar Paper, Bicol Uneversity 1983)
Bondoc, Virginia B. Skill Acquired by Garment Trainees and Skill
Needed by Garment Industry (Unpublished Masters Thesis
Marikina Institute of Science and Technology, 1979)
Laugo, Jon, Vocational Training Policy: International Issues. ADB
Technical Vocational and Trainning 1991
Mantives, Doesdado. Improvised Overhead Projectors (Unpublished
Feasibility Study Marikina Institute of Science and
Technology, 1983 )
Andabon, Bonnie A. on his thesis an Automotive Engine Ignition System
Circuit Trainer an Evaluation on its Effectiveness to
Automotive Instruction,
copyright (2005) study at Zamboanaga City State
Polytechnic College.
Azul de Leon, Lacson. Published the hydraulic brake master cylinder in
trainer,
copyright (2007) study here in at Zamboanaga City State
Polytechnic College.
-
8/4/2019 Hydraulic Valve Spring Compressor
37/39
Appendix A
CURRICULUM VITAE
NAME: Gilbert C. Dela Pea
DATE OF BIRTH: November 14, 1986
FATHER: Romualdo Dela Pea
MOTHER: Elena Dela Pea
EDUCATIONAL ATTAINMENT:
ELEMENTARY: Bless Elementary School
HIGH SCHOOL: Siocon National High School
COLLEGE: Zamboanga City State Polytechnic College
COURSE: Bachelor of Science in Automotive Technology
-
8/4/2019 Hydraulic Valve Spring Compressor
38/39
Appendix B
CURRICULUM VITAE
NAME: Eric S. Lara
DATE OF BIRTH: February 08 1987
PLACE OF BIRTH: Latap Limpapa Zamboanga City
CIVIL STATUS: Single
FATHER: Warlito A. Lara
MOTHER: Martina A. Lara
EDUCATIONAL ATTAINMENT:
ELEMENTARY: Latap Elementary School
HIGH SCHOOL: Labuan National High School
COLLEGE: Zamboanga City State College
COURSE: Bachelor of Science in Automotive Technology
-
8/4/2019 Hydraulic Valve Spring Compressor
39/39
Appendix C
CURRICULUM VITAE
NAME: Manny G. Valledor
DATE OF BIRTH: November 25, 1982
PLACE OF BIRTH: Zamboanga City
CIVIL STATUS: Single
FATHER: Godofredo C. Valledor
MOTHER: Laura G. Valledor
EDUCATIONAL ATTAINMENT:
ELEMENTARY: Tumaga Elem. School
HIGH SCHOOL: Z.C.H.S(Main)
COLLEGE: Zamboanga City State Polytechnic College
COURSE: Bachelor of Science in Automotive Technology