HYDRAULIC PUMP CATALOG - QBE · PDF fileHYDRAULIC PUMP CATALOG. CV. ... Hand wheel control....

2015 – 2016

CV. QBE Nusantara

Jl. Sutan Sahrir no. 21 A Taliwang – Sumbawa Barat, Nusa Tenggara Barat

HYDRAULIC PUMP CATALOG

CV. QBE Nusantara

EATON Vickers PVB,

PFB series Axial Piston

Pump

Basic Characteristics

Type..................................Axial piston pumps

Operating pressure......up to 210 bar (3000 psi)

Displacement................10,5 to 197,5 cm3/r

(0.64 to 12 in3/r)

Drive speed.....................up to 3600 r/min

- Typical Section

Variable displacement model with compensator

control “C” or “CM”

- General Description

both fixed and variable displacement models

make up this range of axial piston pumps. Their

high performance ratings and efficiencies are

achieved with a variety of hydraulic fluids. Fixed

displacement models are noted for their

volumetric and mechanical efficiencies. Variable

displacement models can closely match pressure

and/or flow demand with a control selected from:

Pressure compensator with or without a remote

control facility.

Pressure compensator with adjustable

displacement control.

Load sensing compensator.

Mechanical (lever) control.

Hand wheel control.

CV. QBE Nusantara

EATON Vickers PVH Variable Axial Piston Pump

PVH Piston Pumps

High flow, high performance pumps for industrial and mobile applications

Introduction:

PVH high flow, high performance pumps are a family of variable displacement, inline piston units that incorporate

the proven design, quality manufacturing techniques and operating features of other Vickers piston pumps, but in a

smaller, lighter package.

The PVH series has been specially designed to meet the 250 bar (3625 psi) continuous duty performance

requirements of new generation equipment designs. These are efficient, reliable pumps, with a selection of optional

CV. QBE Nusantara

controls for maximum operational flexibility. Designed specifically for strenuous application, they provide the

productivity gains and controllability improvements desired in earthmoving, construction, machine tool, plastics,

and all other energy-conscious markets. As with all Vickers products, these pumps have been fully laboratory

tested and field proven.

PVH Series Benefit:

Versatile design includes single pumps, thru-drive arrangements, and a variety of drive shaft and control options

that will adapt to any application and provide the most cost effective installation.

Proven components designed into a heavy duty, compact housing to provide 250 bar (3625 psi) continuous

operating performance, and 280 bar (4050 psi) operating performance in a load sensing system. This design assures

long life at the higher performance levels required of today’s power-dense machinery.

Compact and lightweight designed to reduce the application weight, and provide better access for installation and

servicing. Service kits developed for the most critical rotating and control components to simplify and assure

successful pump servicing. Quiet designs available for noise-sensitive industrial applications, reducing sound levels

further to provide a more acceptable environment. Design for maximum efficiency in any type of application. A

variety of compensators provide the most effective system control, and the 95%-plus volumetric efficiency means

more flow, and more input energy, is directed to the work and not into heat and waste. Heavy duty bearings and

shafts result in minimum internal deflections and wear, providing for longer life and maximum uptime.

Vickers PVH pumps are designed to provide the highest levels of system performance with noise levels within

OSHA requirements. The standard models exhibit low sound levels across a wide range of operating speeds and

pressures to accommodate the conditions necessary for high performance mobile vehicles. In addition, the quieter

QI models provide even lower sound levels at typical in-plant conditions.

Sound is generated by a variety of factors associated with the system, machine, and environment.

EATON Vickers PVQ Piston Pump

PVQ piston pumps are in-line, variable displacement units and are available in nine sizes. Displacement is variedby

means of pressure and/or flow compensator controls. An impressive assortment of control options offers maximum

operating flexibility. PVQs operate at quietness levels that meet today’s demanding industrial conditions. The

sound level of each unit approaches or is below that of the electric motor driving it. Sound is reduced by a patented

timing arrangement that also produces low pressure “pulses” in the outlet flow. This leads to reduced tendencies for

noise in systems using PVQs. The PVQ series is capable of operating with many types of hydraulic fluid. Water-

content and phosphate ester fluids can be accommodated, in addition to the typical petroleum based and synthetic

fluids.

Many PVQ pumps are available in a thru-drive configuration to accommodate a multitude of application and

installation requirements. Thru-drive models can be coupled to various types and sizes of fixed and variable

CV. QBE Nusantara

displacement pumps, resulting in a compact and versatile package. Such a package offers lower installed cost by

reducing the installation size and by requiring only one mounting pad on the prime mover. Quiet PVQs have

excellent operating characteristics, and the pumps many control and mounting options allow choosing the optimum

model for any application. Additionally, PVQs possess the same durability and long life characteristics expected of

the best industrial products in today’s marketplace.

Vickers MFB and MVB Hydraulic Piston motor

Model: MFB5UY21, MFB10UY31, MFB20UY10, MFB29UY10, MFB45UY10

These motors are of axial piston, fixed or variable displacement, inline design. The units can be operated in either

direction of rotation. Flow direction is as indicated. MFB motors are variable horsepower – horsepower being

CV. QBE Nusantara

approximately proportional to rpm with a given constant operating pressure. Service may be continuous,

intermittent, continuous reversing, or stalled without damage when properly protected by a relief valve. Output

speeds are dependent on input flow. Speed ranges of at least 36:1 are possible at the maximum torque rating by

varying flow to the motor. Vickers fixed displacement inline piston motors offer a choice of five torque ratings,

speed from 100 to 3600 r/min and pressures to 210 bar (3000 psi). Reversible shaft rotation and flange or foot

mountings are available.

High Efficiency

Overall operating efficiency can be as high as 93% and volumetric efficiency as high as 97%, depending on motor

size, pressure, speed, fluid viscosity, and temperature. High speeds, pressures and efficiencies give Vickers inline

piston motors power density. The result is high performance in a compact package that requires minimum

installation space. Rotation can be reversed simply by reversing the direction of flow through the motor ports.

Minimum speed can vary between 50 and 100 r/min, depend upon motor size and characteristics of the drive load.

Vickers piston motors are designed to meet the specifications shown in the “Ratings” section of this catalog. To

ensure maximum performance in conjunction with your specific application, consult your Vickers sales

representative if you’re: Pressure requirements are above 100 bar (1500 psi). Speed is above 1800 r/min rating.

Speed is below minimum recommended speed of 100 r/min. System requires fire resistant or other fluids.

Operating temperature is not within the range of 38 to 66 C (100 to 150 F). With proper application and fluid

consideration, a greater temperature range is permissible. Oil viscosities at operation condition are not within 100

to 250 SUS. Application requires an indirect drive. Oil viscosity at start-up is in excess of 1000 SUS mounting

attitude is other than horizontal.

Sauer PV Axial Piston Pumps

Axial piston variable displacement pumps, Series 20, are of swash plate’s construction with variable flow

capability suitable for hydrostatic transmission with closed loop circuit.

Axial piston variable displacement pumps, Series 20, are well-engineered and easy to

handle. The full-length shaft with a high efficient tapered roller bearing arrangement offers a

CV. QBE Nusantara

high loading capacity for external radial forces. Additional pumps can be built on. The hydro-

mechanical servo displacement control maintains the selected swash plate position and

hence pumps displacement. Upon release of the control handle, the swash plate

automatically returns to the null position and the flow becomes zero.

High case pressures can be archived without leakage even at the lowest temperature by

using suitable shaft seals. The servo valve arrangement offers the facility to incorporate

function regulators and remote control system. Axial piston units are designed for easy

servicing, complete dismantling and reassembly can be carried out standard hand tools, and

all components or sub-assemblies are replaceable.

Sauer MF Axial Piston Motor

CV. QBE Nusantara

Axial pistons fixed displacement motors, Series 20, are of swash plate construction with preset displacement, and

are intending for closed circuit operation. The output speed is proportional to the flow rate of the input fluid. The

output torque is proportional to the differential between high and low pressure sides of the fluid circuit. The

direction of motor (output) shaft rotation depends upon which port the fluid enters the motor.

Figure 1: Axial piston fixed displacement motors, Series 20, are well-engineered and easy to handle. The full-

length shaft with a highly efficient tapered roller bearing arrangement offers a high loading capacity for external

radial forces. High case pressures can be achieved without leakage even at the lowest temperatures by using

suitable shaft seals. The modular construction of the units simplifies the production of a wide variety of model

options while limiting the number of different components involved.

Light weight, short version available on request.

Figure 2 shows schematically the function of a hydrostatic transmission using an axial piston variable displacement

pump a fixed displacement motor.

Rexroth A4VSO Variable Axial Piston Hydraulic Pump

Series: 10, 22, 30. With open circuit

Nominal pressure 5100 psi (350 bar).

Peak pressure 5800 psi (400 bar)

Figure :

– Swash plate design

– Infinitely variable displacement

– Good self priming suction characteristics

– Continuous operating pressure of 5100 psi (350 bar)

– Low noise level

– Low power to weight ratio

– Drive shaft able to accept axial and radial loading

– Excellent service life

– Compact modular design

– Short control times

– Over-centre design (swallow circuits)

– Through drive and pump combinations possible

– Swivel angle indicator standard

– Installation positional optional

– Interchangeable with original Rexroth pump of same model

CV. QBE Nusantara

Rexroth A10VSO Variable Axial Piston pumps

Open circuit

Size: 18, 28, 45, 71,100, 140

Series: 31

Nominal pressure 280 bar. Peak pressure 350 bar

Features:

Axial piston pump A10VSO, variable, in swash plate design for hydrostatic transmissions in open loop

circuit

Flow is proportional to drive speed and displacement. By adjusting the swash plate angle it is possible to

infinitely vary the flow

Mounting flange acc. to SAE J744

Flanged ports acc. to SAE J518

2 case drain ports

Good suction characteristics

Permissible working pressure 280 bar

Low noise level

Long service life

Axial and radial loading of drive shaft possible

High power to weight ratio

Wide range of controls

CV. QBE Nusantara

Short response times

Interchangeable with original Rexroth pump of the same model

Rexroth A2F Fixed Axial Piston Hydraulic Pump & Motor

Axial piston unit of bent axis design with fixed displacement, for use as either pump or motor in hydrostatic drives,

in open or closed circuit.

If operated as a pump, the flow is proportional to the drive speed and displacement. If operated as a motor, the

output speed is proportional to the swept volume and inversely proportional to displacement. The output torque

increases with the pressure drop between the high and low pressure sides.

Features:

Equivalent with original Rexroth same model.

High performance rotary group with well-proven spherical control area with the advantages, self-centring

low peripheral speed, high efficiency.

Robust rolling bearing endure long service life.

Drive shaft capable of adopting radial loading.

Rexroth A2FO & A2FM Fixed Bent Axis Piston Pump & Motor

Fixed displacement pumps & motors

• Nominal pressure: Nominal size5: 315 bar

CV. QBE Nusantara

Nominal sizes 10 to 200: 400 bar


• Peak pressure:

Nominal size5: 350 bar



• Series 6

• Open circuit

• Robust and short taper roller bearings

• Standard fixed displacement pump for all applications in open circuit

• Service ports SAE or threaded

• Cylindrical shaft end with spliced shaft or keyed shaft

• Interchangeable with original Rexroth pump and motor of the same model

The fixed displacement pump A2F of axial piston, bent axis design is made suitable for hydrostatic drives in open

circuits. Output flow is proportional to drive speed and displacement. These pumps are suitable for use in mobile or

industrial applications. The drive shaft bearings are designed to give the service life expected in these areas of

operation. Careful selection of the displacements offered, permit sizes to be matched to practically every

application.

– Favourable power / weight ratio

– Compact and economic design

– Optimum efficiency

– One piece pistons with piston rings

– Patented cylinder block drive system

Rexroth A7V series Axial Piston Variable Pump

Series 2.0 and 5.1. Axial piston unit, bent axis design. Size 20 to 500, high pressure range up to 40MPa (400 bar)

CV. QBE Nusantara

Rexroth A2VK Chemical Froth Axial Piston Metering Pump

Open Circuit Functions

Size Rexroth A2VK12, A2VK28, A2VK55, A2VK107 Pump

Nominal pressure 250 bar

Maximum pressure 315 bar

Version for pumping plastic components

Features

– Chemical Froth Hydraulic Axial Piston Polyurethane Metering Pump

– High metering accuracy and reproducibility of the variable pumped volumes

– Robust manual adjustment via hand wheel with integral precision measuring scale

– Operating pressure up to 250 bar

– Low pulsation of the pumped medium

– Pump components are compatible with the pumped media (polyol, isocyanate) due to special pairings of

materials and sealing elements

CV. QBE Nusantara

– Low-noise

– Excellent volumetric efficiency for high metering accuracy

– Double shaft seals with buffer fluid ports to guarantee safe operation (and protect the environment)

– With corrosion protection

Rexroth A6VM & A6V Variable Piston Hydraulic Motor

Large controls range with hydrostatic transmissions. Secondary controls regulation with various control devices.

Increased maximum output speeds at reducing swivel angle. Cast-saving due to possibility due to using smaller

pumps. Obviates the multispeed ratio gear drives. Highs power density. Optional mount position. Efficient,

Excellent starting characteristics and Low inertia.

Size: 28-250 ml/rev. Nominal pressure: 35MPa. Peak pressure: 40MPa

Rexroth A2FE Fixed Displacement Plug-in Hydraulic Piston Motor

Series 6, axial tapered piston, bent axis design for mounting in mechanical gearboxes

Nominal Pressure up to 400 bar Peak Pressure up to 450 bar

CV. QBE Nusantara

The fixed displacement plug-in motor A2FE is equipped with a standard axial tapered piston rotary group of bent

axis design. Hydrostatic plug-in motors are intended primarily for installation in mechanical gearboxes, e.g. track

drive gear boxes.

The design of the motor with the mounting flange in the centre of the housing allows it to be almost fully integrated

into a mechanical gearbox to give an extremely compact unit.

– complete unit, ready assembled and tested

– easy assembly, simply «plugs-in» to mechanical gearboxes

– no installation tolerances to consider

– Interchangeable with original Rexroth motor of the same model.

Rexroth A10V variable axial piston hydraulic pump

Normal size: 16, 18, 28, 45, 71, 100, 140

Parts: Piston shoe, Cylinder block, Ball guide, Retainer plate, Coupler,

Retainer & ball guide, Cam Rocker, Press pin, Coil spring, Big spring, Small bearing, Swash plate piston, etc.

Rexroth A7V piston variable pump spare parts

Size: 20, 28, 40, 55, 58, 80, 107, 160, 250, 500, 1000

Parts: Head cover (LR, EL), Servo piston, Servo piston pin, Piston Valve plate (L, R), Cylinder block, Coil spring,

Socket blot, Retainer plate, Ring of piston, Canter pin, Drive shaft, etc.

CV. QBE Nusantara

Rexroth A2F Piston Pump / Motor Spare Parts

Size: 10, 12, 23, 28,45,55, 63,80,107, 125,160,200, 250, 355,500, 1000

Parts: Valve plate (R, L), Cylinder block, Retainer plague, Piston, Disk spring, Disk spring holder, Centre pin,

Drive shaft, Socket bolt, Half ring, Bush, etc.

K3V series Piston Pump Parts

Parts: Valve plate(R, L), Cylinder block, Retainer plate, Piston, Disk spring, Disk spring holder, Center pin, Drive

shaft, etc.

Model: K3V112DT, K3V140DT, K3V180DT, K5V140, K5V200, NV64, NV84, NV111DT, NV137, NV172,

NV270, KVC925 KVC930, KVC932, etc.

Caterpillar Piston Pump

Parts: Valve plate Cylinder block, Retainer plage, Piston, Disk spring, Disk spring holder, Center pin, Drive shaft,

Socket bolt, etc.

CV. QBE Nusantara

Model: VRD63 (CAT120), AP-12(double-pump), AP-14(double-pump) CAT320C, SPK10/10(E200B), CAT12G,

CAT14G, CAT16G, CAT215, CAT330, CAT992, etc.

Rexroth A4VG, A4VSO series Piston Variable Pump Spare Parts

Normal size: 28, 40, 56, 71, 90, 125, 180

Parts: Valve plate (R, L), Cylinder block, Retainer plague, Piston, Drive shaft, Ball guide, Housing, Head block,

Side plate, etc.

K3V63 of Kawasaki piston pump parts

Parts: Piston shoe, Cylinder block, Valve plate, Retainer plate, ball guide, Retainer & ball guide, shoe plate, Yoke

ashy, Shaft coupler, Barrel washer, Coil spring, Block spring, Feed back rod, etc.

SAUER series piston pump spare parts

CV. QBE Nusantara

Denison Vane Pump, Parker Denison Hydraulic T6C T6D T6E T7E Single Vane

Pump

Features

T6C T6D T6E Series are fixed displacement and balanced type single Denison hydraulic vane pumps. The

pump is designed for higher operating pressure and greater flow at the same housing size.

With a balanced pin-vane design, outlet pressure is continuously applied only to the pin. The pin provides

the steady light force against the vane. Top and bottom areas of the vane are subject to the same pressure,

either inlet or outlet pressure, depending on the vane’s location during rotor rotation. This pin-vane design

minimizes noise level and improves volumetric efficiency.

With the cartridges are independent of the shaft, allowing for easy change of flow capacity and field

servicing. Without remove the pumps from its mounting.

Parker Denison Hydraulic T6CC T6DC T6EC T6ED Double Vane Pump

Features:

• T6CC, T6DC, T6EC, T6ED, etc. Series are fixed displacement and balanced type Denison double hydraulic vane

pumps. The pump is designed for higher operating pressure and greater flow at the same housing size.

• With a balanced pin-vane design, outlet pressure is continuously applied only to the pin. The pin provides the

steady light force against the vane. Top and bottom areas of the vane are subject to the same pressure, either inlet or

outlet pressure, depending on the vane’s location during rotor rotation. This pin-vane design minimizes noise level

and improves volumetric efficiency, easy change of flow capacity and field servicing without.

• With the cartridge independent of the shaft, allowing for removing the pump from its mounting.

CV. QBE Nusantara

Tokimec SQP Hydraulic Vane Pump

Single Vane Pump SQP1, SQP2, SQP3, SQP4. SQPS1, SQPS2, SQPS3, SQPS4

Double Vane Pump SQP21, SQP31, SQP32, SQP41, SQP42, SQP43

Triple Vane Pump SQP211, SQP311, SQP321, SQP421, SQP431, SQP432

Model: SQP21-19-8-1DC-18

EATON Vickers VQ VQH Hydraulic Vane Pump

Features

•Eaton Vickers V and VQ series are fixed displacement and balanced type vane pumps. Available in both 12

vanes, designs for industrial. Applications with quiet operating and 10 vanes design for mobile application with

higher pressure and wider strange of speed. They are widely used in hydraulic systems for machine-tools, presses,

die casting machine, engineering, plastic injection moulding and other machineries.

•Its interchangeable with original Vickers pump of the same model.

•The inlet or outlet ports can be rotated through increments of 90°in relation to each other, providing application

flexibility and easy installation.

•With the cartridge independent of the shaft, allowing for easy change of flow capacity and field servicing without

removing the pump from its mounting.

•For the cartridge kit of VQ Series, the flexible plates are inserted between the support plates and the rotor. The

flexible plates are assembled with the bronze facing towards the rotor to improve cold start capability and

compensate thermal expansion in the rotor. This makes VQ Series particularly suited for mobile application.

•This series of pumps are developed to meet the increasing demands of machine--tool industry.

•Total 4 series including 19 kinds are available, whose displacement ranges from 18 ml/r to 193 ml/r, max

continuous operating pressure is 17.2 MPa, the speed of rotation ranges from 600 rpm to 1800 rpm. The intra-vane

structure ensure many good characteristics such as high pressure, large capacity, small volume, smooth operation,

low noise, efficient capacity efficiency and long service life etc. The main technical data has reached an advanced

level in the international market of the same trade.

•This series of pump is composed of replaceable cartridge kits, which reduce the construction time thus enhance

production efficiency. Optimum design of pump core further reduce the pressure shimmy, flow pulsation and noise

of the pump, sound pressure balance which compensate the space can have better capacity efficiency. The proper

CV. QBE Nusantara

design of oil supply system between vane and intra-vane enables good contact between blade and stator and ensure

minimum flow loss. The unique design, high-precision processing and rational material selections prolong the

service life of the pump. With complete specifications, reliable performance, simple and rational structure,

convenient installation and repairing (the connection complies with IS O and SAE), the pump is widely used in

machine-tool, press and die-casting machines, engineering, plastic injection moulding and other machineries.

EATON Vickers V10 & V20 Power Steering Vane Pump

Features

•EATON Vickers 10 and V20 series are fixed displacement and balanced type vane pumps. With compact sizes,

they are available in single pumps and double pumps for both industrial and mobile application.

•The vane design with self compensation for wear and clearances makes volumetric efficiency of pump nearly

constant over the service life. (the vanes always adjust its orbit to contact with the cam ring, even though wear

occurs between the cam ring and vane tips)

•The vane pump is not damaged at low speed and high pressure operation because pumping action does not start

until the speed is high enough for the vane to throw out. With hydraulically balanced design, the bearing is

externally loaded only. Therefore, the pump requires minimized maintenance with long service life.

•The inlet or outlet ports can be rotated through increments of 90o in relation to each other, providing application

flexibility and easy installation.

•With optional flow control and priority valve covers, the pump can be used in more applications. The flow control

cover can limit the flow to the primary circuit at the required flow rate, while diverts remaining flow to the tank. The

priority valve cover maintains a constant flow to the primary circuit, while diverts remaining flow to the secondary

circuit. Each cover comes with a relief valve to limits the maximum pressure of the primary circuit.

•Interchangeable with original Vickers pump of the same model.

Handling

•For maximum service life, the pump should be protected from contamination. Filtering fluid before filling and during

operation to maintain or exceed ISO cleanliness code 17/14. Replaceable elements should be changed as filter

supplier instructions.

•The drive shaft must align with the power source shaft. Avoiding shaft end thrust and applications that impose

radial loading.

•The start-up procedures should be as follows:

CV. QBE Nusantara

- Check the rotation of power source to match the rotation of pump.

- Check inlet and outlet ports to assure all connections are properly installed and check all mounting bolts and

flanges to assure all are tight and properly aligned.

- Fill pump with fluid through the outlet port if the pump is mounted above the fluid level. The spline shaft models

also need to be lubricated with an anti-fretting grease or similar lubricant.

- Place all controls in the neutral position so the pump is unloaded during initial start-up.

- Prime the pump within a few second when the pump is started.

- Bleed off entrapped air from outlet circuit until a steady output flow is observed.

Model: Eaton Vickers V10, V20, V10F, V20F, V10P, V20P single vane pump and Vickers V2010, V2020, V2010F,

V2020F, V2010P, V2020P double vane pump.

Eaton Vickers Hydraulic Vane Pump V series

Model: V10: 3.3-22.8(ml/r), V20: 19.5-42.4(ml/r) Vickers V2010, V2020, V2010F, V2020F, V2010P, V2020P

Model: V20-1P1P-1C

Eaton Vickers VTM42 Power Steering Hydraulic Vane Pump

We offers a complete line of economical high performance fixed displacement VTM hydraulic vane pumps

providing flows up to 25 US GPM and pressures to 2000 psi for mobile and marine power steering applications.

The integral flow control and relief valve eliminate the need for external valve and combined with the top mount

reservoir, you have a compact power package. Units can be supplied with a manifold assembly to be piped to an

external tank or assembled on existing installations. Units are supplied with a threaded shaft and a heavy duty front

bearing for gear and pulley drive assemblies.

CV. QBE Nusantara

Parker Denison T6C T6D T6E T7E Hydraulic Vane Pump Cartridge Kits

Single- Denison hydraulic Vane Pump T6C,T6D, T6E, T7E

Double- Denison hydraulic Vane Pump T6CC, T6DC, T6ED, T6EC

Triple- Denison hydraulic Vane Pump T6DCC, T6EDC, T6DDC

Denison hydraulic single, double, triple vane pumps replacement.

Instruction for the Parker Denison Hydraulic T6C, T6D, T6E, T7E vane pump:

ROTATION & PORTS INDICATION: The rotation and ports orientation are viewed from the shaft end.

CW stands for clockwise, right-hand rotation. CCW stands for counter-clockwise, left-hand rotation.

START-UP CHECK-UP：

Check that the assembly of the power unit is correct: The distance between the suction pipe & the return lines in the

tank should be at its maximum. A bevel on both suction & return lines is recommended to increase the surface and

so lower the velocity. We suggest a 45° minimum angle.

Velocities: inlet 0,5 < x < 1,9 m/s (1,64 < x < 6,23 ft per sec.) : return x < 6 m/s (x < 19,7 ft per sec.) : Always

insure that all return and suction lines are under the oil level to avoid forming aeration or vortex effect. This should

be done under the most critical situation (all cylinders extended for example). Straight and short pipes are the best.

Start-up : The tank has been filled up with a clean fluid in proper conditions. Flushing the system with an external

pump prior to the start-up is good. To allow a good priming of the pump, the air should be bled off.

START-UP INSTRUCTIONS & RECOMMENDATIONS

the first valve on the circuit should be open to tank. Air bleed off valves are available on the market place. It is

possible to bleed off the air by creating a leak in the P port of the pump.

SHAFT & COUPLING DATA

DENISON Hydraulics supplies the T6 series keyed shaft pumps with high strength heat-treated keys. Therefore,

when installing or replacing these pumps, the heat treated keys must be used in order to ensure maximum life in the

application. If the key is replaced, it must be a heat-treated key between 27 and 34 R.C hardness. The corners of the

CV. QBE Nusantara

keys must be chamfered by 0,76 mm to 1,02 mm (0.03 to 0.04) at 45° to clear the radii in the key way. The

alignment of keyed shafts must be within tolerances given for splined shafts here above.

RECOMMENDED FLUIDS

Petroleum based anti-wear R & O fluids. These fluids are the recommended fluids for pumps & motors. Maximum

catalog ratings and performance data are based on operation with these fluids. These fluids are covered by

DENISON Hydraulics HF-0 and HF-2 specifications.

ACCEPTABLE ALTERNATE FLUIDS:

The use of fluids other than petroleum based anti-wear R & O fluids requires that the maximum ratings of the umps

will be reduced. In some cases the minimum replenishment pressures must be increased. Consult specific sections

for more details

VISCOSITY (for Industrial)

Max. (cold start, low speed & pressure) 860 cSt - 3900 SUS

Max. (full speed & pressure) 108 cSt - 500 SUS

Optimum (max. life) 30 cSt - 140 SUS

VISCOSITY INDEX: 90 min. Higher values extend the range of operating temperatures.

TEMPERATURES: The usual limitation factor of temperature (low or high) comes from the obtained viscosity.

The seals are sometimes the limit: standard seals range from -30° C to 90° C (-9.4° F to 194° F).

WATER CONTAMINATION IN THE FLUID

Maximum acceptable content of water:

0,10 % for mineral base fluids.

0,05 % for synthetic fluids, crankcase oils, biodegradable fluids.

If the amount of water is higher, then it should be drained off the circuit.

EATON Vickers V, VQ VQH Hydraulic Vane Pump Cartridge Kits

CV. QBE Nusantara

Features:

• Replacement parts for fixed displacement Vickers hydraulic vane pumps (single and double vane pump V,VQ,

VQH series).

• Available in both 12 vanes design for industrial application with quiet operating and 10 vanes design for mobile

application with higher pressure and wider range of speed.

• With the cartridge independent of the shaft, allowing for easy change of flow capacity and field servicing without

removing the pump from its mounting.

• We produced full range of EATON Vickers cartridge kits for the V, VQ, VQH series single and double Vickers

hydraulic vane pump.

Tokimec SQP & SQPS Hydraulic Vane Pump Cartridge Kits

For Single vane pump: SQP1, SQP2, SQP3, SQP4,

Double vane pump: SQP21, SQP31, SQP32, SQP41, SQP42,

Tripe vane pump: SQP43, SQP321, SQP421, SQP432, SQP211, SQP311, SQP431

The Tokimec SQP series hydraulic vane pumps feature low noise and are offered in 4 frame sizes, 16 series, 32

models of different displacements and as triple pump which allow user to select the combination which best

matches their circuit for optimum energy efficiency.

CV. QBE Nusantara

1. Offers very quiet and “soft” operational noise levels.

2. Multiple pump combinations of differing displacements permits simpler circuit design compare to system using

one large displacement pump and provide greater flexibility in circuit design with benefit of low noise levels.

3. Rotation element is in cartridge kit from which allows simple maintenance.

Caterpillar OEM Hydraulic Vane Pump and its Cartridge kits

Machine: Scraper, Wheel Dozer, Compactor, Track Loader

OEM model: 3G2722, 1U2664, 3G7653, 3G2196, 6E2396, etc

ATOS Hydraulic Vane Pump PFE & PFED Cartridge Kits

CV. QBE Nusantara

Vickers Vane Motor Cartridge

Cartridge kits for Eaton Vickers Vane Motor 25M, 35M, 45M and 50M

Features

• Replacement parts for High Torque Vane Motors (25M, 35M, 45M and 50M series)

• With the cartridge independent of the shaft, allowing for easy change of flow capacity and field servicing without

removing the motor from its mounting.

• High speed and high-pressure motors ranging from 43.9 to 193.2 cm3 / r with 172 bar of maximum pressure and 9

torque rating choices. The internal inlet chambers are equally and diametrically opposed resulting in balanced in

radial loads.

• Thus, the motors are hydraulically balanced which reduced wear and heat from friction.

• These motors provide 90% efficiency due to dual pressure plates, which produced low internal leakage.

•Motors are bi-rotational, simply reversed by reversing in flow direction.

CV. QBE Nusantara

HYDRAULIC PUMP CATALOG - QBE · PDF fileHYDRAULIC PUMP CATALOG. CV. ... Hand wheel control....

Documents

Transcript of HYDRAULIC PUMP CATALOG - QBE · PDF fileHYDRAULIC PUMP CATALOG. CV. ... Hand wheel control....