HVR-HD1000 V1

HVR-HD1000U/HD1000N/HD1000E/ HD1000P/HD1000CSERVICE MANUALVer. 1.0 2007.11Revision History

US Model Canadian Model AEP Model E Model Chinese Model

N MECHANISM (MDX-N220)

LinkSPECIFICATIONS MODEL INFORMATION TABLE SERVICE NOTE DISASSEMBLY BLOCK DIAGRAMS FRAME SCHEMATIC DIAGRAMS SCHEMATIC DIAGRAMS PRINTED WIRING BOARDS REPAIR PARTS LIST ADJUSTMENTS INSTRUCTION MANUAL

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

Les composants identifis par une marque 0 sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.

DIGITAL HD VIDEO CAMERA RECORDER

HVR-HD1000U/HD1000N/HD1000E/HD1000P/HD1000C

9-852-240-11

Sony EMCS Co.

2007K0500-1 2007.11 Published by Kohda TEC

These specifications are extracted from instruction manual of HVR-HD1000E/HD1000P.

SPECIFICATIONSSystemVideo recording system (HDV) 2 rotary heads, Helical scanning system Video recording system (DV) 2 rotary heads, Helical scanning system Still image recording system Exif Ver. 2.2*1 Audio recording system (HDV) Rotary heads, MPEG-1 Audio Layer -2, Quantization: 16 bits (Fs 48 kHz, stereo) transfer rate: 384 kbps Audio recording system (DV) Rotary heads, PCM system Quantization: 12 bits (Fs 32 kHz, stereo 1, stereo 2), 16 bits (Fs 48 kHz, stereo) Video signal PAL color, CCIR standards 1080/50i specification Usable cassette Mini DV cassette with the mark printed Tape speed (HDV) Approx. 18.81 mm/s Tape speed (DV) SP: Approx. 18.81 mm/s LP: Approx. 12.56 mm/s Recording/playback time (HDV) 60 min (using a DVM60 cassette) Recording/playback time (DV) SP: 60 min (using a DVM60 cassette) LP: 90 min (using a DVM60 cassette) Fast forward/rewind time Approx. 2 min 40 s (using a DVM60 cassette and rechargeable battery pack) Approx. 1 min 45 s (using a DVM60 cassette and AC Adaptor) Viewfinder Electric viewfinder (color) Image device 6.3 mm (1/2.9 type) CMOS sensor Recording pixels (still, 4:3): Max. 6.1 mega (2 848 2 136) pixels *2 Gross: Approx. 3 200 000 pixels Effective (movie, 16:9): Approx. 2 280 000 pixels Effective (movie, 4:3): Approx. 1 710 000 pixels Effective (still, 16:9): Approx. 2 280 000 pixels Effective (still, 4:3): Approx. 3 040 000 pixels Lens Carl Zeiss Vario-Sonnar T 10 (Optical), 20 (Digital) Focal length f=5.4 ~ 54 mm (7/32 ~ 2 1/4 in.) When converted to a 35 mm still camera In TAPE: 40 ~ 400 mm (1 5/8 ~ 15 3/4 in.) (16:9), 49 ~ 490 mm (1 15/16 ~ 19 3/8 in.) (4:3) In MEMORY: 40 ~ 400 mm (1 5/8 ~ 15 3/4 in.) (16:9), 37 ~ 370 mm (1 1/2 ~ 14 5/8 in.) (4:3) F1.8 ~ 2.9 Filter diameter: 37 mm (1 1/2 in.) Color temperature [AUTO], [ONE PUSH], [INDOOR] (3 200 K), [OUTDOOR] (5 800 K)HVR-HD1000U/HD1000N/HD1000E/HD1000P/HD1000C

Minimum illumination 5 lx (lux) ([AUTOSLW SHTR] [ON], Shutter speed 1/25 sec) 0 lx (lux) (during NightShot function)*1 Exif is a file format for still images, established by the JEITA (Japan Electronics and Information Technology Industries Association). Files in this format can have additional information such as your camcorders setting information at the time of recording. *2 The unique pixel array of Sonys ClearVid CMOS sensor and image processing system (new Enhanced Imaging Processor) allows for still image resolution equivalent to the sizes described.

Input/Output connectorsVIDEO OUT jack Pin jack 1 Vp-p, 75 (ohms) S VIDEO OUT jack 4pin mini DIN Luminance signal: 1 Vp-p, 75 (ohms) Chrominance signal: 0.3 Vp-p, 75 (ohms) AUDIO OUT jack Pin jack Audio signal: 327 mV (at load impedance 47 k (kilohms)), Output impedance with less than 2.2 k (kilohms) COMPONENT OUT jack Y: 1 Vp-p, 75 (ohms) PB/PR, CB/CR: 350 mV, 75 (ohms) HDMI OUT jack Type A (19-pin) Headphone jack Stereo minijack ( 3.5 mm) LANC jack Stereo mini-minijack ( 2.5 mm) USB jack B MIC (PLUG IN POWER) jack Stereo minijack ( 3.5 mm) HDV/DV jack i.LINK Interface (IEEE1394, 4-pin connector S100)

Operating temperature 0 C to + 40 C (32 F to 104 F) Storage temperature -20 C to + 60 C (-4 F to + 140 F) Dimensions (approx.) 265 231 460 mm (10 4/8 9 1/8 18 1/8 in.) (w/h/d) including the projecting parts 265 231 460 mm (10 4/8 9 1/8 18 1/8 in.) (w/h/d) including the projecting parts with the supplied battery pack NP-F570 attached Mass (approx.) 2.7 kg (6 lb 0 oz) main unit only 3.0 kg (6 lb 10 oz) including the NP-F570 rechargeable battery pack and cassette (PHDVM-63DM), and lens hood with lens cover, microphone. Supplied accessories See page 5-35.

AC Adaptor AC-L100Power requirements AC 100 V - 240 V, 50/60 Hz Current consumption 0.35 - 0.18 A Power consumption 18 W Output voltage DC 8.4 V* Operating temperature 0 C to + 40 C (32 F to 104 F) Storage temperature -20 C to + 60 C (-4 F to + 140 F) Dimensions (approx.) 48 29 81 mm (1 15/16 1 3/16 3 1/4 in.) (w/h/d) excluding the projecting parts Mass (approx.) 170 g (6.0 oz) excluding the power cord (mains lead)* See the label on the AC Adaptor for other specifications.

Rechargeable battery pack (NP-F570)Maximum output voltage DC 8.4 V Output voltage DC 7.2 V Capacity 15.8 Wh (2 200 mAh) Dimensions (approx.) 38.4 20.6 70.8 mm (1 9/16 13/16 2 7/8 in.) Mass (approx.) 100 g (3.5 oz) Operating temperature 0 C to + 40 C (32 F to 104 F) Type Lithium ionDesign and specifications are subject to change without notice.

LCD screenPicture 6.7 cm (2.7 type, aspect ratio 16:9) Total dot number 211 200 (960 220)

GeneralPower requirements DC 7.2 V (battery pack) DC 8.4 V (AC Adaptor) Average power consumption During camera recording using the viewfinder with normal brightness: HDV recording 4.4 W DV recording 4.2 W During camera recording using the LCD & viewfinder with normal brightness: HDV recording 4.8 W DV recording 4.6 W

2

These specifications are extracted from instruction manual of HVR-HD1000U/HD1000N.

SPECIFICATIONSSystemVideo recording system (HDV) 2 rotary heads, Helical scanning system Video recording system (DV) 2 rotary heads, Helical scanning system Still image recording system Exif Ver. 2.2*1 Audio recording system (HDV) Rotary heads, MPEG-1 Audio Layer -2, Quantization: 16 bits (Fs 48 kHz, stereo) transfer rate: 384 kbps Audio recording system (DV) Rotary heads, PCM system Quantization: 12 bits (Fs 32 kHz, stereo 1, stereo 2), 16 bits (Fs 48 kHz, stereo) Video signal NTSC color, EIA standards 1080/60i specification Usable cassette Mini DV cassette with the mark printed Tape speed (HDV) Approx. 18.81 mm/s Tape speed (DV) SP: Approx. 18.81 mm/s LP: Approx. 12.56 mm/s Recording/playback time (HDV) 60 min (using a DVM60 cassette) Recording/playback time (DV) SP: 60 min (using a DVM60 cassette) LP: 90 min (using a DVM60 cassette) Fast forward/rewind time Approx. 2 min 40 s (using a DVM60 cassette and rechargeable battery pack) Approx. 1 min 45 s (using a DVM60 cassette and AC Adaptor) Viewfinder Electric viewfinder (color) Image device 6.3 mm (1/2.9 type) CMOS sensor Recording pixels (still, 4:3): Max. 6.1 mega (2 848 2 136) pixels*2 Gross: Approx. 3 200 000 pixels Effective (movie, 16:9): Approx. 2 280 000 pixels Effective (movie, 4:3): Approx. 1 710 000 pixels Effective (still, 16:9): Approx. 2 280 000 pixels Effective (still, 4:3): Approx. 3 040 000 pixels Lens Carl Zeiss Vario-Sonnar T 10 (Optical), 20 (Digital) Focal length f=5.4 ~ 54 mm (7/32 ~ 2 1/4 in.) When converted to a 35 mm still camera In TAPE: 40 ~ 400 mm (1 5/8 ~ 15 3/4 in.) (16:9), 49 ~ 490 mm (1 15/16 ~ 19 3/8 in.) (4:3) In MEMORY: 40 ~ 400 mm (1 5/8 ~ 15 3/4 in.) (16:9), 37 ~ 370 mm (1 1/2 ~ 14 5/8 in.) (4:3) F1.8 ~ 2.9 Filter diameter: 37 mm (1 1/2 in.) Color temperature [AUTO], [ONE PUSH], [INDOOR] (3 200 K), [OUTDOOR] (5 800 K)HVR-HD1000U/HD1000N/HD1000E/HD1000P/HD1000C

Minimum illumination 5 lx (lux) ([AUTOSLW SHTR] [ON], Shutter speed 1/30 sec) 0 lx (lux) (during NightShot function)*1 Exif is a file format for still images, established by the JEITA (Japan Electronics and Information Technology Industries Association). Files in this format can have additional information such as your camcorders setting information at the time of recording. *2 The unique pixel array of Sonys ClearVid CMOS sensor and image processing system (new Enhanced Imaging Processor) allows for still image resolution equivalent to the sizes described.

Input/Output connectorsVIDEO OUT jack Pin jack 1 Vp-p, 75 (ohms) S VIDEO OUT jack 4pin mini DIN Luminance signal: 1 Vp-p, 75 (ohms) Chrominance signal: 0.286 Vp-p, 75 (ohms) AUDIO OUT jack Pin jack Audio signal: 327 mV (at load impedance 47 k (kilohms)), Output impedance with less than 2.2 k (kilohms) COMPONENT OUT jack Y: 1 Vp-p, 75 (ohms) PB/PR, CB/CR: 350 mV, 75 (ohms) HDMI OUT jack Type A (19-pin) Headphone jack Stereo minijack ( 3.5 mm) LANC jack Stereo mini-minijack ( 2.5 mm) USB jack B MIC (PLUG IN POWER) jack Stereo minijack ( 3.5 mm) HDV/DV jack i.LINK Interface (IEEE1394, 4-pin connector S100)

Operating temperature 0 C to + 40 C (32 F to 104 F) Storage temperature -20 C to + 60 C (-4 F to + 140 F) Dimensions (approx.) 265 231 460 mm (10 4/8 9 1/8 18 1/8 in.) (w/h/d) including the projecting parts 265 231 460 mm (10 4/8 9 1/8 18 1/8 in.) (w/h/d) including the projecting parts with the supplied battery pack NP-F570 attached Mass (approx.) 2.7 kg (6 lb 0 oz) main unit only 3.0 kg (6 lb 10 oz) including the NP-F570 rechargeable battery pack and cassette (PHDVM-63DM), and lens hood with lens cover, microphone. Supplied accessories See page 5-35.

AC Adaptor AC-L100Power requirements AC 100 V - 240 V, 50/60 Hz Current consumption 0.35 - 0.18 A Power consumption 18 W Output voltage DC 8.4 V* Operating temperature 0 C to + 40 C (32 F to 104 F) Storage temperature -20 C to + 60 C (-4 F to + 140 F) Dimensions (approx.) 48 29 81 mm (1 15/16 1 3/16 3 1/4 in.) (w/h/d) excluding the projecting parts Mass (approx.) 170 g (6.0 oz) excluding the power cord (mains lead)* See the label on the AC Adaptor for other specifications.

Rechargeable battery pack (NP-F570)Maximum output voltage DC 8.4 V Output voltage DC 7.2 V Capacity 15.8 Wh (2 200 mAh) Dimensions (approx.) 38.4 20.6 70.8 mm (1 9/16 13/16 2 7/8 in.) (w/h/d) Mass (approx.) 100 g (3.5 oz) Operating temperature 0 C to + 40 C (32 F to 104 F) Type Lithium ionDesign and specifications are subject to change without notice.

LCD screenPicture 6.7 cm (2.7 type, aspect ratio 16:9) Total dot number 211 200 (960 220)

GeneralPower requirements DC 7.2 V (battery pack) DC 8.4 V (AC Adaptor) Average power consumption During camera recording using the viewfinder with normal brightness: HDV recording 4.6 W DV recording 4.4 W During camera recording using the LCD & viewfinder with normal brightness: HDV recording 5.0 W DV recording 4.8 W

3

Model information tableModel Destination Color system HVR-HD1000U US, CND NTSC HVR-HD1000N E NTSC HVR-HD1000E AEP PAL HVR-HD1000P E PAL HVR-HD1000C CH PAL

Abbreviation AR : Argentine model AUS : Australian model BR : Brazilian model CH : Chinese model CND : Canadian model EE : East European model HK : Hong Kong model J : Japanese model JE : Tourist model KR : Korea model NE : North European model


4

CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PISES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPMENTS PUBLIS PAR SONY.

SAFETY CHECK-OUTAfter correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. Check the B+ voltage to see it is at the values specified. Flexible Circuit Board Repairing Keep the temperature of the soldering iron around 270C during repairing. Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). Be careful not to apply force on the conductor when soldering or unsoldering. Unleaded solder Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.) : LEAD FREE MARK Unleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.

2. 3.

4.

5. 6.


5

1. SERVICE NOTE1-1. POWER SUPPLY DURING REPAIRSIn this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4 V), the power is shut off so that the unit cannot operate. These following method is available to prevent this. Method: Use the AC power adaptor (AC-L100).

1-2. TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT)1 Refer to 2. DISASSEMBLY to remove the mechanism deck block. 2 Supply +4.5 V from the DC power supply to the loading motor and unload with a pressing the cassette compartment.

Loading motor DC power supply (+ 4.5 Vdc)

1-3. SETTING THE FORCED POWER ON MODEIt is possible to turn on power by adjustment remote commander (RM-95 or NEW LANC JIG). Operate the VTR function using the adjustment remote commander.

1-3-1. Setting the Forced Camera Power ON Mode1) Select page: 0, address: 01, and set data:01. 2) Select page: A, address: 10, set data:01 and press the PAUSE (Write) button of the adjustment remote commander.

1-3-2. Setting the Forced VTR Power ON Mode1) Select page: 0, address: 01, and set data:01. 2) Select page: A, address: 10, set data:02 and press the PAUSE (Write) button of the adjustment remote commander.

1-3-3. Exiting the Forced Power ON Mode1) Select page: 0, address: 01, and set data:01. 2) Select page: A, address: 10, set data:00 and press the PAUSE (Write) button of the adjustment remote commander. 3) Select page: 0, address: 01, and set data: 00.


1-1

1-4. USING SERVICE JIGConnect the CPC-15 jig connector (J-6082-564-A) and I/F unit for LANC control (J-6082-521 A) to the CN8102 on the US-014 board.CN8101

CPC-15 (J-6082-564-A)81 8

FLexible Flat Cable (FFC-107)

FP-786 Flexible

CN8001 (SIDE B)

CN1012

MS-379 BOARD (SIDE A) US-014 BOARD (SIDE A)

VC-500 BOARD (SIDE A)

CN8003

CN8102

1

I/F unit for LANC control (J-6082-521-A)

1-5. SELF-DIAGNOSIS FUNCTION1-5-1. Self-diagnosis FunctionWhen problems occur while the unit is operating, the self-diagnosis function starts working, and displays on the viewfinder or LCD screen what to do. Details of the self-diagnosis functions are provided in the Instruction manual.Viewfinder or LCD screenC:31:11

1-5-2. Self-diagnosis DisplayWhen problems occur while the unit is operating, the counter of the viewfinder or LCD screen shows a 4-digit display consisting of an alphabet and numbers, which blinks at 3.2 Hz. This 5-character display indicates the repaired by:, block in which the problem occurred, and detailed code of the problem.

Blinks at 3.2Hz

CRepaired by: C : Corrected by customer H : Corrected by dealer E : Corrected by service engineer

31Block

11Detailed Code

Refer to 1-5-3. Self-diagnosis Code Table . Indicates the appropriate step to be taken. E.g. 31 ....Reload the tape. 32 ....Turn on power again.


1-2

1-5-3. Self-diagnosis Code TableSelf-diagnosis CodeRepaired by:

Block Function 0 2 2 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 4 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 2

Detailed Code 0 0 0 1 1 2 2 2 2 3 3 4 4 4 4 4 1 1 2 2 2 2 3 3 4 4 4 4 4 0 0 0 0 1 0 1 2 3 0 1 0 1 2 3 4 0 1 0 1 2 3 0 1 0 1 2 3 4

Symptom/State

Correction

C C C C C C C C C C C C C C C C C C C C C C C C C C C C C

Non-standard battery is used. Condensation. Video head is dirty. LOAD direction. Loading does not complete within specified time UNLOAD direction. Loading does not complete within specified time T reel side tape slacking when unloading. S reel side tape slacking when unloading. T reel fault. S reel fault. FG fault when starting capstan. FG fault during normal capstan operations. FG fault when starting drum. PG fault when starting drum. FG fault during normal drum operations. PG fault during normal drum operations. Phase fault during normal drum operations. LOAD direction loading motor timeout. UNLOAD direction loading motor time-out. T reel side tape slacking when unloading. S reel side tape slacking when unloading. T reel fault. S reel fault. FG fault when starting capstan. FG fault during normal capstan operations. FG fault when starting drum. PG fault when starting drum. FG fault during normal drum operations. PG fault during normal drum operations. Phase fault during normal drum operations.

Use the InfoLITHIUM battery. Remove the cassette, and insert it again after one hour. Clean with the optional cleaning cassette. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. If it does not recover, inspect the focus MR sensor of lens block (Pin qh, qk of CN5301 on the LD-229 board). If not faulty, inspect the focus motor drive circuit (IC5404 on the LD-229 board).

C

3

2

6

0

Difficult to adjust focus. (Cannot initialize focus.)


1-3

Self-diagnosis CodeRepaired by:

Block Function

Detailed Code

Symptom/State

Correction

E

6

1

1

0

Zoom operations fault. (Cannot initialize zoom lens.) Focus lens initializing failure and zoom lens initializing failure occur simultaneously. Steadyshot function does not work well. (With pitch angular velocity sensor output stopped.) Steadyshot function does not work well. (With yaw angular velocity sensor output stopped.) Abnormality of IC for steadyshot.

Inspect the zoom MR sensor of lens block (Pin w;, wa of CN5301 on the LD-229 board) when zooming is performed when the zoom switch is operated and the zoom motor drive circuit (IC5404 on the LD-229 board) when zooming is not performed. Check both C: 32: 60 and E: 61: 10 of the self-diagnosis code. Inspect pitch angular velocity sensor (SE7202 on the CM-077 board) peripheral circuits. Inspect yaw angular velocity sensor (SE7201 on the CM-077 board) peripheral circuits. Refer to [1-7-1. E : 62 : 02 (Abnormality of IC for Steadyshot) Occurred].

E

6

1

1

1

E

6

2

0

0

E E E E E E E

6 6 6 6 6 6 6

2 2 2 2 2 2 2

0 0 0 1 1 1 2

1 2 3 0 1 2 0

IC for steadyshot and micro controller Inspect the steadyshot circuit (IC5703 on the LD-229 board). communication abnormality among. Refer to [1-7-2. E : 62 : 10 (Shift Lens Initializing Failure) Shift lens initializing failure. Occurred]. Refer to [1-7-3. E : 62 : 11 (Shift Lens Overheating (Pitch)) Shift lens overheating (Pitch). Occurred]. Refer to [1-7-4. E : 62 : 12 (Shift Lens Overheating (Yaw)) Shift lens overheating (Yaw). Occurred]. Refer to [1-7-5. E : 62 : 20 (Abnormality of Thermistor) Abnormality of thermistor. Occurred].


1-4

1-6. METHOD OF COPING WITH SHIFT LENS ERRORLD-229 BOARD (SIDE A)

VC-500 BOARD (SIDE A)

R1823

R5737

IC5703

R5721

R1823R5792

IC1801

IC1801

Fig. 1 Measurement points on the LD-229 board

Fig. 3 Measurement points on the VC-500 board

about 330 msec

Note: The length of low section will vary a little depending on the conditions.

Fig. 2 Change in output voltage of R5792 on the LD-229 board

1-6-1. E : 62 : 02 [Abnormality of IC for Steadyshot] OccurredOrder 1 2 3 Turn the power OFF. While measuring with an oscilloscope the output voltage of R5792 in the periphery of IC5703 on the LD-229 board, turn the power ON to check that the output voltage immediately after the power on change as shown in Fig. 2. If the output voltage change as shown in Fig. 2, replace the lens block (Note). If it does not change as shown in Fig. 2, inspect the camera control circuit (IC1801 of VC-500 board) periphery. Procedure

Note: When the lens block was replaced, execute a necessary adjustment items referring to 6. ADJUSTMENT. After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.


1-5

1-6-2. E : 62 : 10 [Shift Lens Initializing Failure] OccurredConnect the adjustment remote commander (RM-95 or NEW LANC JIG) and perform the following process. Order Page Address Data 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 2 2 2 01 02 01 00 2D 0 0 F (7F) F (7F) F (7F) F (7F) F (7F) F (7F) 0 0 01 10 06 06 06 07 07 07 10 01 D07 00 00 Perform Hall Adjustment. (Note 1) If the lens does not move at all when adjusting it, proceed to the order 12. When the adjustment ends, proceed to the order 16. (Note 1) Press PAUSE (Write) button. Read the data value. If value is not 01, inspect the EEPROM (IC1802 of VC-500 board). When value is 01, proceed to the order 14. Press PAUSE (Write) button. Turn the power OFF and ON again. Check that no error occurs. If an error occurs, replace the lens block (Note 2). D06 01 07 Read the data value and assume it as D06. Change the data and check that it has been changed. If no value changes or if value is 00 or FF, inspect the EEPROM (IC1802 of VC-500 board). If value changes, proceed to the order 5. Press PAUSE (Write) button. Read the data value and assume it as D07. Change the data and check that it has been changed. If no value changes or if value is 00 or FF, inspect the EEPROM (IC1802 of VC-500 board). If value changes, proceed to the order 8. Press PAUSE (Write) button. Procedure

Note 1: Perform adjustment by referring to Hall Adjustment in 6. ADJUSTMENT. After the adjustment, be sure to perform Angular Velocity Sensor Sensitivity Adjustment. Note 2: When the lens block was replaced, execute the necessary adjustment items referring to 6. ADJUSTMENT. After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.


1-6

1-6-3. E : 62 : 11 [Shift Lens Overheating (Pitch)] OccurredConnect the adjustment remote commander (RM-95 or NEW LANC JIG) and perform the following process. Order Page Address Data 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 0 0 B (6B) 0 D (7D) D (7D) D (7D) D (7D) D (7D) D (7D) 0 B (6B) 0 0 01 10 B2 10 46 48 48 46 48 48 10 B2 10 01 01 06 01 07 F0 01 00 10 01 00 06 00 00 00 Check if the shift lens moves while setting the order 5 to 10. If the shift lens does not move, replace the lens block (Note 2). When the shift lens moved, proceed to the order 16. While setting the order 5 to 10, measure with an oscilloscope the output voltage of R5721 in the periphery of IC5703 on the LD-229 board to check the output voltage varies. If the output voltage does not vary, replace the lens block (Note 2). When the output voltage varied, proceed to the order 18. Turn the power OFF. While measuring with an oscilloscope the output voltage of R5792 in the periphery of IC5703 on the LD-229 board, turn the power ON to check that the output voltage immediately after the power on change as shown in Fig. 2. If the output voltage change as shown in Fig. 2, replace the lens block (Note 2). If it does not change as shown in Fig. 2, inspect the camera control circuit (IC1801 of VC-500 board) periphery. Press PAUSE (Write) button. Press PAUSE (Write) button. Press PAUSE (Write) button. (Note 1) Press PAUSE (Write) button. Press PAUSE (Write) button. Press PAUSE (Write) button. (Note 1) Press PAUSE (Write) button. Press PAUSE (Write) button. Procedure

20

Note 1: Finish this operation within 10 seconds. If it is likely to take more than 10 seconds, set page: D (7D), address: 48, data: 00, and then retry. Note 2: When the lens block was replaced, execute the necessary adjustment items referring to 6. ADJUSTMENT. After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.


1-7

1-6-4. E : 62 : 12 [Shift Lens Overheating (Yaw)] OccurredConnect the adjustment remote commander (RM-95 or NEW LANC JIG) and perform the following process. Order Page Address Data 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 0 0 B (6B) 0 D (7D) D (7D) D (7D) D (7D) D (7D) D (7D) 0 B (6B) 0 0 01 10 B2 10 47 49 49 47 49 49 10 B2 10 01 01 06 01 07 F0 01 00 10 01 00 06 00 00 00 Check if the shift lens moves while setting the order 5 to 10. If the shift lens does not move, replace the lens block (Note 2). When the shift lens moved, proceed to the order 16. While setting the order 5 to 10, measure with an oscilloscope the output voltage of R5737 in the periphery of IC5703 on the LD-229 board to check the output voltage varies. If the output voltage does not vary, replace the lens block (Note 2). When the output voltage varied, proceed to the order 18. Turn the power OFF. While measuring with an oscilloscope the output voltage of R5792 in the periphery of IC5703 on the LD-229 board, turn the power ON to check that the output voltage immediately after the power on change as shown in Fig. 2. If the output voltage change as shown in Fig. 2, replace the lens block (Note 2). If it does not change as shown in Fig. 2, inspect the camera control circuit (IC1801 of VC-500 board) periphery. Press PAUSE (Write) button. Press PAUSE (Write) button. Press PAUSE (Write) button. (Note 1) Press PAUSE (Write) button. Press PAUSE (Write) button. Press PAUSE (Write) button. (Note 1) Press PAUSE (Write) button. Press PAUSE (Write) button. Procedure

20

Note 1: Finish this operation within 10 seconds. If it is likely to take more than 10 seconds, set page: D (7D), address: 49, data: 00, and then retry. Note 2: When the lens block was replaced, execute the necessary adjustment items referring to 6. ADJUSTMENT. After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.

1-6-5. E : 62 : 20 [Abnormality of Thermistor] OccurredOrder 1 2 3 Turn the power ON. Check that R1823 in the periphery of IC1801 on the VC-500 board is 0 and energizes. If it is not energizes, replace the R1823. When R1823 is 0 and energizes, replace the lens block (Note). Check that no error occurs, after replacing the lens block and performing the necessary adjustment. If an error occurs, inspect the camera control circuit (IC1801 of VC-500 board) periphery. Procedure

Note: When the lens block was replaced, execute the necessary adjustment items referring to 6. ADJUSTMENT. After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.HVR-HD1000U/HD1000N/HD1000E/HD1000P/HD1000C

1-8E

2. DISASSEMBLYNOTE FOR REPAIR Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Do not insert the cable insufficiently nor crookedly. When remove a connector, dont pull at wire of connector. It is possible that a wire is snapped. When installing a connector, dont press down at wire of connector. It is possible that a wire is snapped. Cut and remove the part of gilt which comes off at the point. (Be careful or some pieces of gilt may be left inside)

NOTE FOR DISCONNECTING THE HARNESS (HN-047)When disconnecting the harness (HN-047), do not pull the harness part but pull off the connector body with tweezers etc.

Harness (HN-047) Tweezers etc.


2-1

2-1. IDENTIFYING PARTSHandle Cover FP-793 Flexible Board

Handle Assy Battery Panel BA-008 Board DC-110 Board HP-150 Board

Handle Lower Cover MC-188 Board

LCD Panel

PD-342 Board RE-038 Board

Grip

JK-355 Board JS-033 Board NS-022 Board

Cabinet (L)

US-014 Board

View Finder

BL-015 Board BH-001 Board FP-784 Flexible Board HI-078 Board

MS-379 Board G Block Lens CM-077 Board EC-001 Board LD-229 Board FP-785 Flexible Board FP-786 Flexible Board FP-787 Flexible Board FP-788 Flexible Board FP-789 Flexible Board FP-867 Flexible Board IF-155 Board VC-500 Board Mechanism Deck

Cabinet (R)

- DISASSEMBLY FLOW 2-2-1. OVERALL SECTION-1 Grip Cabinet (R) 2-2-2. OVERALL SECTION-2 Lens 2-2-3. HANDLE (TALLY) SECTION View Finder 2-2-4. VIEW FINDER SECTION LCD Panel VF Hinge EVF Panel

MO-027 Board SP-048 Board

2-2-5. HANDLE (COVER) SECTION Handle Cover Handle Lower Cover Handle Assy 2-2-6. OVERALL SECTION-3 Battery Panel G Block Cabinet (L) 2-2-7. G BLOCK SECTION IF-155 Board VC-500 Board Mechanism Deck


2-2

HELP2-2. DISASSEMBLY2-2-1. OVERALL SECTION-1Follow the disassembly in the numerical order given.

EXPLODED VIEW

HARDWARE LIST

1 Grip (1-1 to 1-7) 2 Cabinet (R) (2-1 to 2-6)

1-3 (#100) 1-4 (#100)

1 Grip

Overall Section-2(See Page 2-4)

1-1

1-5

1-6 (#103)

2-2 (#100)

2-5 (#104)

2 Cabinet (R)

2-6 1-7 1-2 (#37)

2-3 (#100) 2-4 (#49) 2-1


2-3

2-2-2. OVERALL SECTION-2Follow the disassembly in the numerical order given.

EXPLODED VIEW

HARDWARE LIST

1 Lens (1-1 to 1-9)

Handle (Tally) Section(See Page 2-5)

1-8 Note: Refer to page 2-1 Note for disconnecting the harness (HN-047).

1-5 1-9 1-4HELP 1

1-6 (#49) 1-1 (#49)

1-7 (#49)

1 Lens

1-3HELP 1

1-2


2-4

2-2-3. HANDLE (TALLY) SECTIONFollow the disassembly in the numerical order given.

EXPLODED VIEW

HARDWARE LIST

1 View Finder (1-1 to 1-17)

1-7 (#102)

Handle (Cover) Section(See Page 2-7)

1-8

1-11 (#49)

1-12 (#49)

1-15 1-14 1-10 (#23)

1 View Finder(See Page 2-6)

1-13 1-17 1-6 1-5 1-2 1-4 1-1 (#37) 1-3 1-9 (Slide)

1-16 (#49)


2-5

2-2-4. VIEW FINDER SECTIONFollow the disassembly in the numerical order given.

EXPLODED VIEW

HARDWARE LIST

1 LCD Panel (1-1 to 1-20) 2 VF Hinge (2-1 to 2-2) 3 EVF Panel (3-1 to 3-3)

1-15 1-14 1-10 (#105) 2-2 (#37)

3 EVF Panel

3-1

3-2 (#37) 1-12 1-11 1-13 1-16

1-4 (#37)

1-5

2 VF Hinge1-6 (#37)

1-18 1-17 (#105) 1-19 1-20

3-3

1 LCD Panel1-3 (#49) 1-1 (Rotate) 1-2 (#49)

1-7 (#37) 1-8HELP 2

2-1 (Rotate)

1-9


2-6

2-2-5. HANDLE (COVER) SECTIONFollow the disassembly in the numerical order given.

EXPLODED VIEW

HARDWARE LIST

1 Handle Cover (1-1 to 1-6) 2 Handle Lower Cover (2-1 to 2-6) 3 Handle Assy (3-1 to 3-15)

1-3 (#107) 1-4 3-2 (#49)

1-1 (#107) 1-2

1-5 (#37) 3-3 3-1 (#49) 3-5 (#49)

3 Handle Assy

1 Handle Cover1-6 (Claw) 3-4 (#49) 3-7 (#49) 3-14 (#100) 3-8 (Claw) 3-15 3-6 (#49) 3-10 (#49) 3-12 (#100) 3-13 3-9 (#49)

2 Handle Lower Cover

2-6 (#49) 2-3 3-11

2-1 (#106)

2-2 (#106) 2-4HELP 3

Overall Section-3(See Page 2-8)

2-5


2-7

2-2-6. OVERALL SECTION-3Follow the disassembly in the numerical order given.

EXPLODED VIEW

HARDWARE LIST

1 Battery Panel (1-1 to 1-9) 2 G Block (2-1 to 2-15)

1 Battery PanelHELP 5

1-1HELP 5

1-2

1-9 (#49)

2-10 (#49)

2-9 (Open) 2-11

2-13 (#1)

1-8 (#49)

2-12 (Open)

1-7 (#49) 1-3HELP 5

1-5HELP 5

1-6

1-4HELP 5

2-2 2-4 (#37)

2-6

Cabinet (L) 2 G Block(See Page 2-9)

2-14 (#37) 2-15 (#37) 2-3 2-5 (#37) 2-1

2-7 (#37) 2-8


2-8

2-2-7. G BLOCK SECTIONFollow the disassembly in the numerical order given.

EXPLODED VIEW

HARDWARE LIST

1 IF-155 Board (1-1 to 1-11) 2 VC-500 Board (2-1 to 2-14) 3 Mechanism Deck (3-1 to 3-6)

3 Mechanism Deck2-9 2-7 2-8 2-10 2-14 3-2 2-4 2-2 (Claw) 2-13 2-1 (#1) 1-7

3-1 (#3)

3-4

2-12

2-3 (Claw)

3-6 3-5 (#15) 3-3 (#1)VC

-50

0

2 VC-500 Board

2-6 (#3)

1 IF-155 Board1-11 1-6

1-10 (#37) 2-11 2-5 Note: Refer to page 2-1 Note for disconnecting the harness (HN-047).HELP 6 HELP 4

1-5

1-9 (#49) 1-3 1-4 1-1HELP 6

1-8 1-2


2-9E

HELPSheet attachment positions and procedures of processing the flexible boards/harnesses are shown.

HELP 1: LI-062/FFC-340FFC-340

HELP 3: FFC-329

FFC-329

LI-062

HELP 2: Hinge Cover (Lower)

HELP 4: FP-787

RS-112/ HP-147

Hinge Cover (Lower)

BI-001

FP-787

IF Holder


HELP

HELP 5: IJ-001/IJ-002/DI-003/DI-004/DI-005IJ-002 IJ-001 DI-005

DI-004

DI-003

HELP 6: HN-047/FP-788

Tape AS FP-788 HN-047


HELP

3. BLOCK DIAGRAMSLinkOVERALL BLOCK DIAGRAM (1/7) OVERALL BLOCK DIAGRAM (2/7) OVERALL BLOCK DIAGRAM (3/7) OVERALL BLOCK DIAGRAM (4/7) OVERALL BLOCK DIAGRAM (5/7) OVERALL BLOCK DIAGRAM (6/7) OVERALL BLOCK DIAGRAM (7/7) POWER BLOCK DIAGRAM (1/4) POWER BLOCK DIAGRAM (2/4) POWER BLOCK DIAGRAM (3/4) POWER BLOCK DIAGRAM (4/4)


3. BLOCK DIAGRAMS3-1. OVERALL BLOCK DIAGRAM (1/7)LENS BLOCKIRIS (SHUTTER) IC6701 6M CMOS IMAGER (1/3)

( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

CM-077 BOARD40, 39, 42, 41, 44, 43, 46, 45, 33, 34 31, 32 29, 30 27, 28 18-21 22-25 29-32 37-40 4-1

VC-500 BOARD (1/7)A10, A9, J10, J9, B10, B9 K10, K9

DRVOUT4, DCOUT4, DRVOUT8, DCOUT8 DRVOUT3, DCOUT3, DRVOUT7, DCOUT7 DRVOUT2, DCOUT2, DRVOUT6, DCOUT6 DRVOUT1, DCOUT1, DRVOUT5, DCOUT5 CHCK3/6M XSYS_RST TGVD, TGHD

AD0_0 - AD0_13

AA21 - AA23, AA13 - AA16, U22, U23, AB12 - AB16, V21 - V23, AC14 - AC17, W21 - W23, Y13 Y21 - Y23

J2 - J4, K2 - K4 F3 - F5, G3 - G5 H3, H4

CN6601

CN1201

A : VIDEO SIGNAL

A3 - D3, A4 - E4, F7, E6, E7 A5 - E5

12-9

AD2_0 - AD2_13

23-20 19-16

IC1201 CHCK

ADC_SO, ADC_SCK, XCS_ADC0 CLPOB ADC_TGHD, ADC_TGVD XSYS_RST CAM_VD_HS CHCK

IC1702 CAMERA SIGNAL PROCESSOR (3/23)H1, E2, E1, G4 - G1, D3 - D1, F3 - F1 C3 - C1

G6, F6

2 105, 4

16 114, 5

25 3037, 36

CDS, A/D CONVERTER (1/23)

H5

7, 6, 8

40-38

AHS_SO, AHS_SCK, XCS_AHS SE7202 PITCH SENSOR SE7201 YAW SENSOR 6 20 IC7201 10 PITCH/YAW 16 SENSOR AMP 17 (2/3)

HDI_C0 - HDI_C7

J2 - J4, K2 - K4 F3 - F5, G3 - G5 H3, H4

YAW_AD VST_C_RESET

G23, J22, H21 N21 - N23, AA17 - AA20, P21 - P23, AB17 - AB21, R21 - R23, AC18 - AC21, T21 - T23, Y17 U20, U21 A5, A6, A8, A16 - A21, B4, B6 - B9, B17 - B22, C4 - C9, C17, C18, C20, D6, D7, D17 H4 - H2

HDI_HD, HDI_VD, HDI_OE VCK SD_CK SD_XCS SD_CKE

AE22, AC20, AC22

A10, A9, J10, J9, B10, B9 K10, K9

7 8 9

PITCH_AD

34 33 32

PITCH_AD YAW_AD VST_C_RESET

Y17, AC17, AD19, W18, Y18, AD20, AB18, AC18

1-3

D6 D7 K5

HDI_Y0 - HDI_Y7

AE20, W19, Y19, AD22, AC19, AE21, AA22, AD23

AD1_0 - AD1_13

IC2101 (1/5) BASE BAND SIGNAL PROCESSOR (4/23)

R1

U1 AE23 V22

A3 - D3, A4 - E4, F7, E6, E7 A5 - E5

AD3_0 - AD3_13

LD-229 BOARD (1/2)IC5404 IRIS METER CN5301C5, B6 C6, A5 H1, J1 7, 1

ADC_TGHD, ADC_TGVD XSYS_RST CAM_VD_HS CHCK XSYS_RST

K23, M22

G6, F6

(1/4)

2, 4

I_BIAS H ND FILTER METER I_HALL

3, 5

AHS_TGHD, AHS_TGVD

MH FOCUS MOTOR

C10, B11 A11, A9 K2, L2

ND_DRIVE ND_BIAS ND_HALL

12, 10 11, 9 14, 8

A10 D10 ND FILTER DRIVE K12 L12J11, K11, H12

CN5303 (1/2) 42 2533, 30, 32

CN1010 (1/2) PNDCK 10 CAM_VD 2719, 22, 20

AHS_SO, AHS_SCK, AHS_XCS0 X1701 89.010989 MHz : NTSC 74.250000 MHz : PAL 1 IC1701 CLOCK GENERATOR (3/23) 5 CHCK

H23, K22, J21

J23, L22

C9 A4

J2 J1 J8 R8, N7, R9, N8, P9, M8, G8, G9, F7, F3, G1, U1

MFOCUS MR SENSOR ZOOM MOTOR

B1, C4 F3, E3

FOCUS F_MR_A, F_MR_B ZOOM_A, ZOOM_B, ZOOM_XA, ZOOM_XB Z_MR_A, Z_MR_B

16, 18 24, 25

CAM_SI, CAM_SO, XCAM_SCK XCS_IC_1801 XRST_IC_1801

M7, L8, L2, M3, M2, P1, G2, G3, H1, H2, J3, N2, R1, N3, R2, E8, D7, G7, H9, J7, H8 D8, B9, C8, A9, C7, A8, A2, C3, A1, C2, B1, D2, D3, E2

CAM_SO, CAM_SI, CAM_SCK

IC5403 IC5402 ZOOM MOTOR 2 NOISE FILTER (1/4)K6, F1 7, 1

FOCUS MOTOR DRIVE

J12 H11

14 12

38 40

IC1901 PNDCK EN1, DIRA1, DIRB1 AC11G22, E23, F21

256M SDRAM (5/23)

24, 31, 29

28, 21, 23

MZOOM MR SENSOR NF MOTOR

K9, L9, M9, J9

51-48

E12, E10

20, 21

ZOOM MOTOR DRIVE

EN1, DIRA1, DIRB1

CAM_VD CAM_VD_HS TG_FLD

AC7 AA6 L21

L8, M8

16, 17

36, 35

29-26

L6, L7

MLENS TEMP SENSOR

NF_DRIVE

NF MOTOR DRIVE

NF_EN, NF_SW

23

AB11, Y11, AB10

18 15 A5

34 37

OPTICAL IMAGE STABILIZEROIS TEMP SENSOR PITCH MOTOR THERM PITCH PITCH_OUT H PITCH_IN 31G6, J8 J9, J7 B10, D10 J3, J2 H2, J4 B1, D1 32, 38 33, 39 40-43

CAM_SI, CAM_SO, XCAM_SCK XCS_IC_1801 XRST_IC_1801 PITCH_AD YAW_AD VST_C_RESET 9 10 8 43 42 44 PITCH_AD YAW_AD VST_C_RESET NF_EN, NF_SW LENS_TEMP_AD THERM

D24A00_CAM - D31A07_CAM, DXXA08_CAM - DXXA13_CAM

A4, B4, B5

M

PITCH_HALL PITCH_HALLBIAS

IC5703 OPTICAL IMAGE STABILIZATION DRIVE (2/4)

C9 G5 J5 D5

C22 B14N22, N20

F2 F4 M22 A17 B8

XSYS_RST ZOOM_SW_AD NTSC/XPAL_DET SYS_V

AA7 - AA9, AA11, AA12, AB8 - AB10, AC8, AC9, AC13, Y8, Y10, Y12

AA2, Y2, W4, W2, Y1, V4, V2, W1, P2, P1, N4, N2, N1, M4

TEMP_OUT

LENS_TEMP_AD THERM

TG_FLD D13 CAM_VD_HS D7 CAM_VD A7

J1 K1

XCS_IC_1702_BUS IC_1702_BUS_CLK

AA3 AC5

XSYS_RST ZOOM_SW_AD NTSC/XPAL_DET SYS_V SYS_V XSLOWSHUT_NR

SD_DQ0- SD_DQ31

IRIS DRIVE

D6 D7 K5

AB4 T4

A11 - A15, B12, B13, B15, C12, C13, C15, D12, D13, D15

M

I_DRIVE

SD_A0 - SD_A11, SD_BA0, SD_BA1

11 12 13

OVERALL (7/7) (PAGE 3-7)

MH

YAW YAW_OUT YAW_IN

36, 37 34, 35 47-44

YAW MOTOR

A6 A7

XRST_IC_5703_CPU XDS_RESET

11 13

41 39


R22 P22 F23

IC1801 CAMERA CONTROL (19/23)

Y7, AB7, AB6

YAW_HALL YAW_HALLBIAS

14 15

OVERALL (7/7) (PAGE 3-7) OVERALL (3/7) (PAGE 3-3)

B13

XSLOWSHUT_NR


HI_SI, HI_SO, XHI_SCK XCS_CAMERA

HI_SI, HI_SO, XHI_SCK XCS_CAMERA

A3

DSCK_IC_5703

35

17

DSCK_IC_5703


AC6

05 C1 X1801 20MHz D1

F1AB14, AC14, AB13,

XCS_EEP_C

12, 5, 6

IC1802 128k EEPROM (19/23)

EEP_SI_C, EEP_SO_C, EEP_SCK_C


3-1

AB23, AD24, AB24, AC25, V19, V20, W20, AB25, Y23, Y24, W22, U19, Y25, U20

FP-787 FLEXIBLE BOARD (1/2)

IC1301

ADC_SO, ADC_SCK, XCS_ADC0 CLPOB

CDS, A/D CONVERTER (2/23)

SD_DQ0 - SD_DQ31

SD_DQ0 - SD_DQ15

H5

K21

T20, V25, U25, U23, R19, T22, T24, T25, T23, P19, R20, N24, R22, R23, P24, N19

A3 A10 D9

3-2. OVERALL BLOCK DIAGRAM (2/7)VC-500 BOARD (2/7)P1, P4, P2, N1, M2, M3, L4, K7, N3, P3 T2, R4 P6, R2 M20, L20 K2, L3 N2, M1 L2, M7


RYI0 - RYI3 DV PB RCI0 - RCI3 HYI, HCI ADATAOUT0, ADATAOUT1

RYI0 - RYI3 DV PB RCI0 - RCI3 HYI, HCI ADATAOUT0, ADATAOUT1

E1, E3 A9, B10 B11, C11, E9, B9, C4, D3 F7, C8 A7, C7, A5, B5, C6, B6 A4, B4 A10, E10 F8, C9

R1 W6 W1U3, V3

HDV PB, DV PB HDV REC, DV REC

RFIN RECDT RECCK RECA1, RECA2 OVERALL (4/7) (PAGE 3-4)

16

RYO0 - RYO3 DV REC RCO0 - RCO3 HYO, HCO

RYO0 - RYO3 DV REC RCO0 - RCO3 HYO, HCO ADATAIN0, ADATAIN1

IC2701 HDV STREAM PROCESSOR, MUX/DEMUX, DV SIGNAL PROCESSOR (8/23) HDV-i.LINK, DV-i.LINK PD00 - PD07

IC2101 (2/5) BASE BAND SIGNAL PROCESSOR (4/23)

A : VIDEO SIGNAL A : AUDIO SIGNAL A : VIDEO/AUDIO SIGNAL A : VIDEO/AUDIO/SERVO SIGNAL

L24 N22 F10 C10 A3 N7 B9 A9 F9

FS_EDGE_REF FRAT_REFO THYRQ_FVDI THCRQ_FHDI TFS_FCO MFLG_QRST FLAT_SYNC_FYO0 VLAT_SYNC_FCI VLAT_IN_FYO1

FS_EDGE_REF FRAT_REFO THYRQ_FVDI THCRQ_FHDI TFS_FCO MFLG_QRST FLAT_SYNC_FYO0 VLAT_SYNC_FCI VLAT_IN_FYO1 CK64FSO CKFSO CK27MFO1

C1 D2 A8 F9 C10 A3 F6 F3 F2 M3 L1 F1 M1

V23, V20, V24, W21, V25, U23, U20, U24

L11, K11, K12, J11, H9, H12, H11, G9

A4 - A7

HDV-i.LINK, DV-i.LINK TPA+, TPA-, TPB+, TPB-

17


T25 T23 R20 P20 U21 R25

PCLK0 IDIR0 XPEN0 XIACC0 FCLR0 FR1

F1, F2, G2, H1, H2, J1, E7, E6, J2, K2 D8, E11

L8 E12 M8 L9 M9 J8 J9

IC3401 HDV/DV i.LINK INTERFACE (9/23)

B8 E2 J6 D7

IC_3401_PLL_ON XCS_IC_3401 XRST_LINK XRST_PHY PWD, CNA, LPS, OFR2

Y13, AC13, AA14, AC14, AA15, AC15, AD15, AC16

HDV REC/PB, HDV-i.LINKB19, D19, B20, D20, C21, C20, A22, D21, B22 C22, G20 E14 - E16 D18, C24, B23, D17, B21, B20, A21, B18

IC_2201_CO0 - IC_2201_CO7 IC_2201_HD, IC_2201_VD, IC_2201_FLD IC_2201_VF_SYNC CK_IC_2201_0 CK_IC_2201_1

AD12 AD16 AD17AC17, AC18 AA16, Y17

KCLK ERDY ERE

X3401 24.576 MHz

A20 F16 F19B19, C19 B16, C16

C2

D12

TRRT

B24 D23 B21P23, M24 L19, K24

E18 F24 A22N23, N21 M23, M21

AUDAI, AUENI AUDAO, AUENO

DXXA00_SIM - DXXA07_SIM

HDV REC/PB, HDV-i.LINK EBS[0] - EBS[7]

C18, F18, B18, E19, A18, C17, F17, B17

C1

L2, L3, M3, L4, M4, M6, L6, L7

IC_2201_YO0 - IC_2201_YO7

D24A00_SIM - D31A07_SIM

D23, E23, E24, E21, D20, D24, C23, D21

B17, F17, A19, G17, C18, F18, A20, C19

IC2201

ADATAIN0, ADATAIN1 AUIN21, AUIN22

HDV-MPEG VIDEO ENCODER/DECODER, MPEG AUDIO SIGNAL PROCESSOR AD18 (6/23)AD6, AC4, AD5, AC5, AD4, AA5, AD3, AB2, Y8, W2, Y9, T1, U1, T2, R4, R2, U2, AA2, W1, V2, V1, G1, H1, R1, P5, N5, N2, M2, F1, H2, E2, D2, F2, G2, D7, P2, P1, N1, L5, M4 A4, B5, A5, B7, B6, D8, A6,

R8, P7, P8, N7, N8, M7, M8, L7, L3, M2, M3, N2, N3, P2, P3, R2, A8, B7, B8, C7, C8, D7, D8, E7, E3, D2, D3, C2, C3, B2, B3, A2

BMDT16 - BMDT47

K20, L24, R21, N20, P21, L23, K25, N21, M20, N23, K21, K24, N25, L20, M25, E24, D24, J20, K23 M23, M24 C24, E25

J8, J9, K7, K9, K1, K3, J1, J2, J3, H1, J7, H2, H3, H8, H9

L1 K1 P25 M25 Y16

C25 D23 D25 F23 F24 G23 J3 H24 A23 H23 FRRV, TRRT, TRRV, DRP

SWP ATF_LATCH SCWIN XCS_IC_2701_HD XCS_IC_2701_DV XRST_IC_2701_DV XRST_IC_2701_1

XRST_IC_2701_2 FRRV, TRRT, TRRV, DRP

18


CK27MFO1 CKFSO CK64FSO MCLK

A20 P21 M24 P24

OMAD00 OMAD12, OMADB0, OMADB1

IC_2101_PCRERR IC_2101_SRCH IC_2101_FLD27MF

C5 B3 G3



IC_2101_PCRERR F8 IC_2101_SRCH D9 IC_2101_FLD27MF G9

J1 L2 L1 K1T20, T21, T23, T24, R20, R21, R23, R24

OMCEX OMCKE OMCLK OMCLKX

H7 G1 G2 G3

IC2401 256M DDR-SDRAM (7/23)



D24A00_SIM - D31A07_SIM ALE_SIM XCS_IC_2201 XRST_IC_2201 INT_IC_2201 ALE_SIM XCS_IC_2201 XRST_IC_2201 INT_IC_2201

N24 M20 D16 P20 Y15 AC14 AE15 AB16 AC15 D17AD16, AB14, Y14, AD15, W14, AB13, AE13, AD14 W13, AD13 W17, W16, N20

ALE_SIM MCLK FRRV, TRRV, DRP

35OVERALL (4/7) (PAGE 3-4)

SD_OSD_VD VREF IC_2101_OEREF XCS_IC_2101_SIM XRST_VTR

DXXA08_SIM, DXXA09_SIM


19OVERALL (3/7) (PAGE 3-3) 05

CK64FSO CKFSO


3-2

3-3. OVERALL BLOCK DIAGRAM (3/7)VC-500 BOARD (3/7)


H7, G2, D3, F3, J1, K6, G4, F2, G6, C3, H1, J7, H6, E1, E4, D2, H4, H2, C2, D5 E2, F4 C1, E3 G1, J6

12, 11, 15, 14, 18, 17

HM_R0 - HM_R7 HM_B0 - HM_B7 HM_HD, HM_VD IC_2101_ADAO2 IC_2101_ADAO1 CK_HM CK74MFO CK256FSO

HM_R0 - HM_R7 HM_B0 - HM_B7 HM_HD, HM_VD IC_2101_ADAO2 IC_2101_ADAO1 CK_HM CK74MFO CK256FSO CK64FSO CKFSO

DE_HDMI, D0_HDMI - D23_HDMI

TMDS DATA0 - TMDS DATA2

G9, G10 J9, K10

K2, K1

N25 M19 J3 J2 C24

E9 C11 E1 G1 D10 E10 E11

HDMI SIGNAL PROCESSOR (10/23)

ADAO1_HDMI, ADAO2_HDMI IDCK 256FS_HDMI 64FS_HDMI FS_HDMI

HDMI TRANSMITTER (11/23)

9, 8

TMDS CLOCK

10, 12

IC3101

HSYNC_HDMI, VSYNC_HDMI

F2, F1 C1, D2

IC3201

7, 9, 4, 6, 1, 3

HM_Y0 - HM_Y7

HM_Y0 - HM_Y7

C7, C6 B8 - B5, D1, C1, D12, C12, A8 - A5 B4 - B2, B12 - B9, A4 - A2 A10, A9

CN3202C2, A1 - A10, B1 - B10, C9, C10, D9, D10 K5, K4, K8, K7, J10, K10 J12, J1, K1, K2, K12, L1 - L11, M3 - M11

FP-867 FLEXIBLE BOARD CN001

A : VIDEO SIGNAL A : AUDIO SIGNAL A : VIDEO/AUDIO SIGNAL

HDMI OUT K3 2 HPD 19

F12 H12 G11 F10 J10

D1 E1 H2 H15, 6

HDMI_SDA, HDMI_SCL IC2101 (3/5) BASE BAND SIGNAL PROCESSOR (4/23) F4 C2D3, D2, F2

SDA, SCL

HDMI_SDA, HDMI_SCL XRST_HDMI XCS_IC_3101

21


VSP_SI, VSP_SO, XVSP_SCK

OVERALL (2/7) (PAGE 3-2) R1 U2

19

CK64FSO CKFSO

IC_2101_ADA01 CK256FSO CK64FSO CKFSO CK13MF01

22 23



CN1012 (1/3) OVERALL (4/7) (PAGE 3-4)

FP-786 FLEXIBLE BOARD (1/3)24 26 RF_MON SWP 24 26

MS-379 BOARD (1/3)CN8001 (1/3) CN8003 6 8 3 1

16, 15

G9, G10

F9, F10

US-014 BOARDCN8102 RF_MON 1 SWP 2

CN8101

24

RF_MON SWP

CPC (FOR CHECK)

C4 AE3 AD10AA4, AC3, AD3, AD2, AE2, AC1, AB3, AC2, W4, AA2, Y3, Y1, T7, U6, T4, T6

DACK1_IC_2101 XCS_IC_2101_VM DSCK_VM D0_VM - D15_VM

DACK1_IC_2101 XCS_IC_2101_VM DSCK_VM D0_VM - D15_VM

D12 B16 A10H19, K21, K19, H20, K20, F19, F20, G20, J20, G19, F21, J21, K18, H18, J19, J18

CN8103P1, N1 21, 22 21, 22 3, 4 6, 5

Y19, W18, M19, W19, AA19, AA18, P18, W21, U19, L20, V20, V21, W20, N19, R18, U20, P19, N18, T19, M18, R19

AE8, Y10, Y9, AD8, AC8, AC7, AB8, W9, AE6, AD7, AB6, AE5, W8, AD6, Y7, AE4, AC6, AC5, AD4

USB_D USB_DET X5101 48 MHz

USB_D USB_DET

D D8101 VCC

A1_VM - A19_VMA1_VM - A11_VM, A13_VM D0_VM - D15_VM A1_VM - A21_VM D0_VM - D15_VM

A1_VM - A21_VM

3, 2

(USB) 1

M2 L1

19 2

19

1

8

IC5101 (1/3) DS CONTROL (17/23)A14, C15, D14

4

IC5103 OSCILLATOR DRIVE (17/23)8, 10, 3 8, 10, 3


15 20

DSCK_IC_5703

2 - 11, 20 - 27, 30, 31, 55

33 - 36, 15 39 - 46, 49 - 52

MS_DIO, MS_BS, MS_SCLK XMS_IN Q5101 LED DRIVE XMS_LED_ON

DIO, BS, SCLK INS

4, 2, 8

19 - 24, 2, 3, 5, 6, 8, 9, 11, 35 27 - 32 12, 39, 40, 42, 43, 45, 46, 48, 49 IC5201 16M SDRAM (18/23) 19 CKE_VM 34 C18 XCS_SDRAM_VM 18 C17 XCS_FLASH_UTA A18

CN8004 MEMORY STICK DUO


XSYS_RST

13

IC5202 32M FLASH (18/23)

A15 Y18

6 13

MS_INSERT XACCESS_LED

6 13

6

D8003 (MS ACCESS) 05


3-3

3-4. OVERALL BLOCK DIAGRAM (4/7)VC-500 BOARD (4/7)OVERALL (3/7) (PAGE 3-3)

( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.N MECHANISM DECK (MDX-N220)

24

RF_MON SWP CONT1, SW_PS, ALL_PS

RF_MON SWP CONT1, SW_PS, ALL_PS RFIN HDV PB, DV PB

30 3839, 37, 45

VIDEO HEAD

IC490110, 9

CN49016, 5

ODD XODD, YODD XEVEN, YEVEN

3, 4

RECA1, RECA2

40, 42

VSP_SO, XVSP_SCK

38, 36

OVERALL (2/7) (PAGE 3-2) IC4801 (3/3) (16/23)

16

46 44

2, 3


23

CK13MF01 XRST_VTR

CK13MF01 XRST_VTR

35

REC/PB AMP (15/23)

XODD, YODD XEVEN, YEVEN

35 34

RECDT HDV REC, DV REC RECCK

EVEN IC4801 (1/3) (16/23) M901 DRUM MOTOR1-6

A18, B5, A5

AB9

XCS_IC_4801

SERIAL 37 INTERFACE IC4601 (1/2) Q4607, Q4609 DRUM PWM DRIVE Q4608, Q4610 CAPSTAN PWM DRIVE

C15, B15

G6, E1, D1, C1, A1, B1, D2, C2, E2 - E5, A2, B5, A5, C5, C6, D6, E6, H2 - H5 D5, B6, A6 B2, C3, D4

AB5, Y5, AB4, AB3, AC3, AB2

IC2402

AC15

41

43

A13, A14

16M FLASH (7/23)

Y14

DRUM_PWM CAP_PWM

44 LPF

45

DRUM_ERROR CAP_ERROR

E15 C14

DRUM_VS

64, 67

XRST_VTR FLASH_A15 - FLASH_A20

63, 65, 68

F1 B4

XCS_FLASH

H2

CN4802 DRUM_U, V, W DRUM_U, V, W


X4401 20MHz

DRUM/ CAPSTAN B12 PWM DRIVER (22/23) A11

DRUM MOTOR DRIVE FG AMP PG AMP

MDRUM FG DRUM PG

DRUM_FG DRUM_PG

53 50

52 49

DRUM_FG_SENS DRUM_PG_SENS

10 9

FG PG

D1 IC4401 AC13 C1 MECHA CONTROL (20/23)

XFFREWUP

Q4801


75, 77


25

CAP_VS A9 B9D19, B20

20 - 9

NTSC/XPAL_DET XSYS_RST IC_3401_PLL_ON XCS_IC_3401 XRST_LINK XRST_PHY PWD, CNA, LPS, OFR2 SWP ATF_LATCH SCWIN XCS_IC_2701_HD XCS_IC_2701_DV XRST_IC_2701_DV XRST_IC_2701_1 XRST_IC_2701_2

10 - 15 74, 76, 78

CN4803 CAP U, V, W UHE, VHE, WHE CAP U, V, W UHE, VHE, WHE

M903 CAPSTAN MOTOR

Y10, AC9, A14, D9

D11

4

FG AMP

7, 8

CAP_FG

CAP_FG

FG1, FG2

27, 24

B4 F2 F4 F23 J2 E20 D22

DRUM_FG DRUM_PG CAP_FWD, CAP_ON CAP_FWD, CAP_ON

CAPSTAN MOTOR DRIVE

MHU, HV, HW

1, 80

2-7

FG1, FG2

CAPSTAN FG

B21 B22 D18 H4 G1 G2 D13 B13U4, U2, V1, B18, D15, T4, T2, U1, A16, A21 R4, R2, P2, P1, N4, N2, N1, M4, M2

V23AB20 - AB22

DEW_DET

CN4801 DEW_DET

67-9

DEW+ XMODE_SW_A, XMODE_SW_B, XMODE_SW_C

DEW SENSOR S903 MODE SWITCH

MODE_SW_A - MODE_SW_C

MODE_SW_A - MODE_SW_C IC4801 (2/3) (16/23)

D16, A17

32, 33

69, 72


18

FRRV, TRRT, TRRV, DRP

L22

LM_LIM_DET

LM_LIM_DET

31

LOADING MOTOR DRIVE TAPE END DETECT TAPE TOP DETECT T REEL FG AMP S REEL FG AMP

1-4

LOAD, UNLOAD

LOAD, UNLOAD

LM

LM_LOARD, LM_UNLOAD

M902 LOADING MOTOR

MQ901 TAPE END SENSOR Q902 TAPE TOP SENSOR H902 T REEL SENSOR H901 S REEL SENSOR D902 (TAPE LED)

DXXA00_SIM - DXXA10_SIM D24A00_SIM - D31A07_SIM ALE_SIM XCS_IC_2201 XRST_IC_2201 INT_IC_2201 MCLK XRST_VTR SD_OSD_VD VREF IC_2101_OEREF XCS_IC_2101_SIM HDMI_SDA, HDMI_SCL OVERALL (3/7) (PAGE 3-3) XRST_HDMI XCS_IC_3101 VSP_SI, VSP_SO, XVSP_SCK VSP_SO, XVSP_SCK

AA2, Y2, W4, W2, Y1, V4, V2, W1

AB11

TAPE_END

TAPE_END

21

20

TAPE_END_C

28

TAPE_END

K4 J1 E22 A6 K1 Y18 B8 B7 Y8 G4D10, B10

Y11

TAPE_TOP

TAPE_TOP

19

1826, 27

TAPE_TOP_C

1620, 19

TAPE_TOP

B11

TREEL_FG

TREEL_FG

29

T_REEL

TREEL

22, 23

A11 B15

SREEL_FG TAPE_LED_ON Q4803 LED DRIVE SYS_V XSLOWSHUT_NR

SREEL_FG

25

S_REEL TAPE_LED_K

22, 23

SREEL TAPE_LED_K


35

25

AC8, AB8, AC7

Y13, AC12, Y12

CHIME_SDA, CHIME_SCK VD_SI, VD_SO, XVD_SCK XCS_EVF XCS_LCD EVF_OUT_EN XCS_IC_4401 HI_SI, HI_SO, XHI_SCK REC_PROOF CHIME_SDA, CHIME_SCK XCC_DOWN

13, 14

21

Y15 AB10

D14 V22

12


MIC903 S902 (REC PROOF) REC_PROOF 11 XREC_PROOF CHIME_SDA, CHIME_SCK 4PIN CONNECTOR S901 (CC DOWN)

D6 D8 K22 AC6Y7, AB7, AB6


26XCS_AUVOL XLINE_CNT1A, XLINE_CNT1B, XLINE_CNT2, XLINE_CNT3A, XLINE_CNT3B B19P20, F20, P22, P23, N20

29


18

XCCDOWN_SW


A : VIDEO/AUDIO/SERVO SIGNAL A : SERVO SIGNAL

27

XD4CN XPSV_D4 DEM0, DEM1 XPWAD, XPWDA

R22 N23AB17, Y17 AC10, L23

XCC_DOWN

30



28

XCS_IC_3001 HP_JACK_IN

AC17 D23

05


3-4

3-5. OVERALL BLOCK DIAGRAM (5/7)VC-500 BOARD (5/7)OVERALL (7/7) (PAGE 3-7)


31

XSYS_RST

IF-155 BOARD (1/5)Q2104 - Q2106 K22 F24 J20 BUFFER CN3701 EVRE EVGR EVBL 34 33 3248, 1

BH-001 BOARDCN6003 4 3 5 20 4 3 5 20 EVF_VR EVF_VG EVF_VB EVF_COM CN6002 7 6 8 4 7 6 8 4

BL-015 BOARDCN5901 CN5902 18 19 17 21 COLOR EVF UNIT

CN0102 7 6 8 4 14 15 13 17

CN0103

IC3701 EVF DRIVER (12/23)

20 21 22 26

LCD902

EP_XHD, EP_XVD

18 - 16, 14 - 9, 5

18 - 16, 14 - 9, 2

18 - 16, 14 - 9, 2

18 - 16, 14 - 9, 5

18 - 16, 14 - 9, 5

IC2101 (4/5) BASE BAND SIGNAL PROCESSOR, D/A CONVERTER (4/23)

XCS_EVF XSYS_RST

43 3 EXTDA 31

6 - 10, 12, 14, 16, 30, 24

VD_SI, VD_SO, XVD_SCK

Q3701 EVF BACKLIGHT DRIVE EVF_OUT_EN

D5901 (EVF BACKLIGHT) 1 20 7 7 LED_K 1 1

Q2101 - Q2103 K25 J25 L22B16, C17

BUFFER

CN1017 (1/2) PLRE 25 PLGR 27 PLBL 2923, 19


PD-342 BOARDCN0118 (1/2) PLRE 9 PLGR 7 PLBL 511, 15

5 - 7, 11 - 16, 20

3 - 5, 7 - 12, 16

EVF_HST, EVF_HCK2, EVF_HCK1, EVF_REF, EVF_STB, EVF_VST, EVF_VCK, EVF_EN, EVF_PCG, EVF_PSIG

42, 45, 44

LCD901 CN0104 14 13 125, 3

CN6004 PANEL_VR 14 PANEL_VG 13 PANEL_VB 125, 3

CN6001 20 21 2218, 14

CN6202 PANEL_R 20 PANEL_G 21 PANEL_B 2218, 14

58 57 5663, 64

IC6201 LCD DRIVER

27 28 29

CN6205 VR 6 VG 5 VB 4 TCOM1, TFTCOM1, TFTCOM2, TCOM2 2.7 inch WIDE COLOR LCD UNIT1, 2, 23, 24 7 - 10, 12, 13, 18 - 22

EP_XHD, EP_XVD

EP_XHD, EP_XVD

EP_XHD, EP_XVD VD_SI, VD_SO XVD_SCK VD_SI, VD_SO

PANEL_XHD, EP_XVD VD_SI, VD_SO

PANEL_XHD, PANEL_VD VD_SI, VD_SO, XVD_SCK

51

15, 14, 12

19, 20, 22

11, 10, 8

11, 10, 8



71 - 69

1, 2

1, 2

XCS_EVF EVF_OUT_EN XCS_LCD OVERALL (4/7) (PAGE 3-4) XCS_LCD XCS_LCD

XVD_SCK

9 CN0105 4 3

9

4 3

CN6005 XVD_SCK XCS_LCD Q6001, Q6002 9 9 XCS_LCD 68

13

21

29

XCS_IC_4401 REC_PROOF CHIME_SDA, CHIME_SCK

P10 W10C9, C10, C6, Y16, G10 A4, AA17

SWITCH B5 A3 TP_X TP_Y 8 10 TP_X 26 TP_Y 24 7 5 7 5 TP_X TP_Y 4 6 4 6

BLON 21 EXTDA 53 TP_X TP_Y Q6201, Q6202 CN6201 TP_TOP 5 TP_L 2 TOUCH PANEL I/F TOUCH PANEL TP_R TP_BOT 1 4

HI_SI, HI_SO, XHI_SCK

IC5101 (2/3) HI CONTROL (17/23)

R11 Q5108 TOUCH PANEL SELECT SWITCH

TP_SEL1

9

25

TP_SEL1

6

6

TP_SEL1

5

5

TP_SEL1


13

HI_SI, HI_SO, XHI_SCK XCS_CAMERA Q5103, Q5104 BEEP MODULATOR MELODY V10 AA11

Y12

TP_SEL2

IC6202 LCD BACKLIGHT CONTROL 3 1 KEY_AD6 18 KEY_AD5 17 KEY_AD6 16 KEY_AD5 17

37 - 44, 47, 59, 60

KEY_AD6

SSP, SSPB, SCK, SCKB, LR, PCTL, INIT, UD, GCK2, GCK1, GSP

Q6203 - Q6206 LCD BACKLIGHT DRIVE D6206 - D6208 (BACKLIGHT)


34

1

1

KEY_AD5


MELODY_ENV

32

ZOOM_MIC_CONT SUB/INT_CTRL XMIC_MONO MIC_IN

V11 G2 Y14 W8 V9

FP-784 FLEXIBLE BOARDCN6006 S6001 LCD 2 OPEN/CLOSE_SW IC801 2 OPEN/CLOSE DETECT

A : VIDEO SIGNAL

ON CN6007 05 OFF 1 KEY_AD5 1

RE-038 BOARDCN0851 S0851 (PANEL REVERSE)


3-5

3-6. OVERALL BLOCK DIAGRAM (6/7)VC-500 BOARD (6/7)Q2107 BUFFER


H23 E25 G22

LINE_OUT_Y LINE_OUT_C/PB LINE_OUT_PR

2 4 6

IC2001 COMPONENT OUT AMP (5/23)

35 33 31 40

CN1007 D3_LNO_Y 27 D3_LNO_PB 25 D3_LNO_PR 23 D3_CN 19

FP-788 FLEXIBLE BOARD13 15 17 21

IF-155 BOARD (3/5)CN0119 CN0114 D3_LNO_Y 4 D3_LNO_PB 6 D3_LNO_PR 8 COMPONENT_ JACK_IN 2

JK-355 BOARDCN0701 4 6 8 2

J0703 Y COMPONENT OUT

Pb/Cb Pr/Cr

1, 48 - 45

XLINE_CNT1A, XLINE_CNT1B, XLINE_CNT2, XLINE_CNT3A, XLINE_CNT3B OVERALL (4/7) (PAGE 3-4) IC2101 (5/5) BASE BAND SIGNAL PROCESSOR, DOWN CONVERTER (4/23) IC_2101_ADAO1 CK256FSO CK64FSO CKFSO 9 11 12 10 15 16 LINE_OUT_Y LINE_OUT_C/PB

Q0104 J0701

27

XD4CN XPSV_D4

44 18 CN0113 (1/2) S_Y_OUT 10 S_C_OUT 8 VIDEO_OUT 6 AUDIO_L_OUT AUDIO_R_OUT 2 4

JS-033 BOARD (1/2)CN0702 (1/2) 10 8 6 2 4 88 3 90 57 61 S_Y_I/O S_C_I/O VIDEO_I/O AUDIO_L_I/O AUDIO_R_I/O S_Y_I/O S_C_I/O VIDEO_I/O AUDIO_L_I/O AUDIO_R_I/O

G C Y G S VIDEO

10 7

8 10 12 17 15

32 30 28 23 25

VIDEO L

A/V OUT

PBIN_L PBIN_R


31 30

AUDIO R

22

IC3002 AUDIO AD/DA CONVERTER (14/23) 3 2 RECOUT_L RECOUT_R 35 34

J0702

P22

AUIN11

8

HP-150 BOARDCN0115 XLANC_JACK_IN LANC_SIG CN0603 2 1 2 1 J652 LANC

M22

KASYAON

13, 14 6, 7

XLANC_JACK_IN IC3001 VIDEO OUT, AUDIO IN/OUT (14/23) 65 XHP_JACK_IN OVERALL (7/7) (PAGE 3-7)

38 39

2 1

33

LANC_SIG


32

BEEP ZOOM_MIC_CONT SUB/INT_CTRL XMIC_MONO MIC_IN DEM0, DEM1 XPWAD, XPWDA XCS_IC_3001 HP_JACK_IN

1

39

HP_JACK_IN

10

10

75 77 25 78

HP_L_OUT HP_R_OUT

Q3002, Q3003 MUTE SWITCH

HP_L_OUT HP_R_OUT

5 3

35 37

HP_L_OUT HP_R_OUT

J651 6 8 6 8 (HEADPHONES)


28

34, 33, 30, 31

CN0112

CN0604

5,4,2,3

G5 H3 H6 G3


5,4,2,3

17

TPA+, TPA-, TPB+, TPB-

4-1

HDV-i.LINK, DV-i.LINK TPA+, TPA-, TPB+, TPB-

6, 7, 10, 9

CN0605 HDV/DV

TPA, NTPA, TPB, NTPB

IC2901

MC-188 BOARDJ401 MIC (PLUG IN POWER) CN0401 3 1

IF-155 BOARD (2/5)CN0108 CN0111 EXT_IN_L 3 5 EXT_IN_R 1 3 CN1009 5 3 C8 C1

MIC AMP (13/23) CN1012 (2/3)

FP-786 FLEXIBLE BOARD (2/3)16, 17

MS-379 BOARD (2/3)CN8001 (2/3) CN8002 CN0117 CN0106 (1/2) SP(+), SP(-)

SP-048 BOARD (1/2)CN0501 CN0502 (1/2) (1/2)

MO-027 BOARD (1/2)CN0504 (1/2) CN0505 SP(+), SP(-)

70, 74

G6 H2

10 7 IC2902 MIC LEVEL CONTROL (13/23)

8 5

VOLOUT_L VOLOUT_R

2, 1

2, 1

8, 9

7, 6

1, 2

8, 7

42 44

IC2903 VOLTAGE FOLLOWER (13/23)

4

6 9

23, 24

VSP_SO, XVSP_SCK

12, 13

VSP_SO, XVSP_SCK

26XCS_AUVOL


3

A : VIDEO SIGNAL A : AUDIO SIGNAL A : VIDEO/AUDIO SIGNAL

05


3-6

2,1

SP+, SP-

16, 17

SP901 SPEAKER

3-7. OVERALL BLOCK DIAGRAM (7/7)

( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.VC-500 BOARD (7/7)

LD-229 BOARD (2/2) EC-001 BOARDPH5501, 5502 CN5311 MANUAL FOCUS/ZOOM SENSOR 5 6 2 1 CN5307 1 CN5306 DIAL_A DIAL_B KEY_AD4 CN5303 (2/2) 6 5 7

FP-787 FLEXIBLE BOARD (2/2)46 47 45

CN1010 (2/2)

DIAL_A DIAL_B OVERALL (5/7) (PAGE 3-5) KEY AD5 KEY AD6

KEY AD0 KEY AD1 KEY AD2 KEY AD4

KEY_AD4

34

C5 B3 B4 E2 E1 C2 W9 R8 P11 G9 M15 W3 N14D11, H10, B10, B9

JS-033 BOARD (2/2)S0701 RESET

CN0702 (2/2) XRESET

IF-155 BOARD (4/5)CN0113 (2/2) 12 12CN0118 (2/2)

DIAL_A DIAL_B IR_ON Q1001 LED DRIVE IR_ON NTSC/XPAL_DET

IC5101 (3/3) HI CONTROL (17/23)

SP-048 BOARD (2/2)S0502 NIGHTSHOT

1 OFF ON S0501 DISPLAY/ BATT INFO S0503 BACK LIGHT S0504 4 11 CN0501 (2/2) 3 12

CN0107 KEY_AD4 CN0117 (2/2) N/S_SW

FP-789 FLEXIBLE BOARD (2/2)XRESET 33

CN1017 (2/2) XRESET XBATT_ INFO_SW K2

1

F2 D3 G1J4, L5, K5, H3

XFIRMUP OSD_V XVM_MAD

2

13

XBATT_INFO_SW

33

XBATT_INFO_SW

1 KEY_AD2

B2

BACK_LIGHT_SW 13CN0120 (1/2)

KEY_AD2

21

X5002 32.768kHz

IC_5001_TXD0, IC_5001_RXD0, IC_5001_SCK0, IC_5001_CS XDS_RESET

L2 L3

MO-027 BOARD (2/2)D558,D559 PLAY/EDIT D552 MEMORY D551 TAPE 4 5 CN0504 (2/2) 3 6

MANUAL CN0502 (2/2)

9

6

PON_SW

C8

D13

FP-785 FLEXIBLE BOARD (1/2)5 XVTR_LED 14

XVTR_LED

10

5

XVTR_LED

CN1015 (1/2)

XVTR_LED

E11

XDS_RESET

14


XMEM_LED

12

3

XMEM_LED

3

XMEM_LED

16

XMEM_LED

F10

5

4

XCAM_LED

13

2

XCAM_LED

2

XCAM_LED

17

XCAM_LED

F11 IC5001 HI CONTROL (21/23) A2 XCC_DOWN OVERALL (4/7) (PAGE 3-4) CN1015 (2/2)

CONTROL SWITCH BLOCK (PS90500)PLAY/EDIT S102 POWER OFF (CHG) TAPE MEMORY S101 START /STOP

NS-022 BOARDCN0902 CN0901 XPOWER_SW 3 8 XMODE_SW 2 7 D901 (NIGHTSHOT) 3 XS/S_SW 10 IR_ON CN0109 XPOWER_SW 5 XMODE_SW 6 16 15 XPOWER_SW XMODE_SW S851 (EJECT) 19 XEJECT_SW B3 3 4 XPOWER_SW XMODE_SW B4 A3

30


IF-155 BOARD (5/5)

DC-110 BOARD

G11

XCHARGE_LED

12

7

CN0120 CN0116 (2/2) XCHARGE_LED

CN0602 1 9 D601 CHG

H2

BATT/XEXT ACV_UNREG, VTR_UNREG, ST_UNREG,

CN1001 161 - 8 10 - 15

1

CN0121 BATT/XEXT ACV_UNREG ACV_GND

4 63, 5

6 45, 7

ACV/XEXT CN0610 DC IN

4

9

4

KEY_AD0

17

XS/S_SW

2

KEY_AD0 C2 FAST_CHARGE Q4603, Q4604 Q4601, Q4602 D4601 CN1003 LF1002

CONTROL SWITCH BLOCK (ZM90500)S202 (PHOTO FREEZE) S201 (PHOTO REC) RV201 W (ZOOM) T 1 5 4 PHOTO

C1 CN0903 PHOTO FREEZE PHOTO REC

INIT_CHARGE_ON

9-16

2-7

BA-008 BOARDCN012211-16 1-6

6 5

7 8

KEY_AD1 PHOTO_REC

13 12

PHOTO_FREEZE PHOTO_REC

6 7 KEY_AD1 A4 BATT_SIG XRESET

BATT_UNREG

BATT_UNREG BATT_SIG BATT_GND

CN0601 8 7 9 2 3 1 1 2 3 3 2 1

CN0652

CN0651 BATTERY TERMINAL

+SW

910 - 16

81-7

ZOOM_AD

4

9

ZOOM_SW_AD

9CN0110

ZOOM_AD 10

P3 ACV_UNREG IC4601 (2/2) A_1.2V, D_1.2V_HV, D_1.2V_K D_1.0V AU_2.8V, D_2.8V, A_2.8V A_4.6V, EP_4.6V, RP_4.6V, AU_4.6V MT_5V D_1.8V CMOS_4.1V, D_3.3V, D_2.5V D_1.5V IC_4601_13.5V N_3.1V N_8.5V CAM_-1.0V CP_-2.8V EVER_3.0V VOUT LANC_DC R2 R1 K3 VBATT CN1012 (3/3)

C

REC START/STOP W

FP-793 FLEXIBLE BOARD2ND_S/S_SW 2ND_ZOOM(W) 4 2 3

HI-078 BOARDCN0201 CN0207 2 7 CN0101 KEY_AD2

11

IR_ON

CN1006 11 10

IR_ON F_TALLY_LED ZOOM_SW_AD SYS_V XSYS_RST NTSC/XPAL_DET NTSC/XPAL_DET XSYS_RST XSYS_RST

E10 LANC_IN LANC_OUT XLANC_PWR_ON XLANC_ON FR_EVER_SO, FR_EVER_SCK BATT_IN XCS_DD VTR_DD_ON

DC CONTROL, RESET, LANC DRIVER (22/23) J3 J2 L3 M3M13, L13

(ZOOM) 2ND_ZOOM(T) T


11 25 20 31 33

C7 A8 B8

B10 C10 B1 B5D2, D1

OVERALL (4/7) (PAGE 3-4) Q201, 202 D201 - D203 (CAMERA RECORDING)5, 6

LED DRIVE

3, 4

XF_TALLY_LED

10

F_TALLY_LED

OVERALL (3/7) (PAGE 3-3) OVERALL (5/7) (PAGE 3-5)

A7 A6 E3 L8

N2 K13C5, N12, N5, C10, C9, F13, G13

XSYS_RST

MS-379 BOARD (3/3) FP-786 FLEXIBLE BOARD (3/3)12 VBATT 12 CN8001 (3/3) BT901 LITHIUM BATTERY

XLANC_JACK_IN OVERALL (6/7) (PAGE 3-6) 05

LANC_SIG

LANC_SIG


3-7

3-8. POWER BLOCK DIAGRAM (1/4)


VC-500 BOARD (1/4)F4601 F4603 VTR_UNREG

DC-110 BOARDCN0602 ACV/XEXT CN0610 DC IN 6 45, 7

IF-155 BOARD (1/3)4 63, 5

F4604 F4605 11 - 8 10 - 15

CN0116 CN0121 BATT/XEXT ACV_UNREG ACV_GND

CN1001

LF1002

Q4607 - Q4610 F4606 CAPSTAN/ DRUM PWM DRIVE L4616 IC_4601_13.5V N_8.5V D_2.8V A_2.8V EP_4.6V RP_4.6V A_4.6V MT_5V A_1.2V D_1.2V_HV D_1.2V_K

2-7

DPOWER (3/4) (PAGE 3-10)

9-16

Q4603, Q4604 Q4601, Q4602 INIT_CHARGE_ON

16

FAST_CHARGE


BA-008 BOARD1-6

D4601 BATT/XEXT 3 2 1 1 2 3 2 3 1 8 7 9 BATT_UNREG BATT_SIG BATT_GND11-16

PVDD1a PVDD1b LX1a LX1b

G14,G15 H14, H15

L4626

L4614 L4628 L4607

CN0652

CN0601

CN0122

CN1003 F4607 BATT_SIG A3 PVDD10 A4 PVDD12 A1 A12 D15 A2 CN1015 (1/2) R1028 13 DVDD1 DVDD2 DVDD3 PVDD11 P1 V_UNREG N1 B_UNREG

+SW

IN1 H13 PVDD2a PVDD2b LX2a LX2bD2, D1 E2, E1

81-7

910 - 16

C

L4601

D_1.0V

IN2 E3 PVDD3a PVDD3b LX3a LX3bK14,K15 J14, J15

8 D601 CHG

2

CN0120 CHARGE_ (1/2) LED_VDD

FP-785 FLEXIBLE BOARD (1/2)6

R5 AVDD1 L1 AVDD3 P15 DVDD4

L4627

L4630 L4610 L4608

AU_2.8V D_2.8V A_2.8V

IN3 J13 PVDD4a PVDD4b LX4a LX4bP12, R12 P11, R11

L4602 D4604

L4615 L4611 L4609 A_4.6V AU_4.6V

CONTROL SWITCH BLOCK (PS90500)PLAY/EDIT OFF (CHG) TAPE MEMORY 3 2

NS-022 BOARDCN0902 CN0901 8 7BATT_UNREG VTR_UNREG

IN4 N11 16 15 3 4 PVDD5a PVDD5b LX5a LX5bB9, A9 B10, A10

CN0109 XPOWER_SW 5 XMODE_SW 6

L4603 D4603

MT_5V

K2, K1

POWER (3/4) (PAGE 3-10)D_2.8V

LANC_DC

L2 LANC_DC(5.6V) SENSEa SENSEb


P9, R9 P10, R10

S102 POWER

D901 (NIGHTSHOT)

A

IN5 C8

CONTROL SWITCH BLOCK (ZM90500)RV201 W (ZOOM) T 2

L4604

L4624

ED_1.8V POWER (2/4) (PAGE 3-9)

R901, R90211, 12

CN09031, 2

33

CN1017 (1/2) XRESET XRESET

R2 VCH P3 RST_OUT(RESET) RSTx K2


G2, G1 F2, F1

FP-789 FLEXIBLE BOARD (1/2)CN0118 (1/2) 1

VBATT D4602

R1 VBATT

IN6 N10 3.3V REG (22/23) Vout 3 2.5V REG (22/23) Vout 3 D_2.5V D_3.3V

IC4605 L4605 4 Vdd IC4603 4 + 3 1 4 Vdd

JS-033 BOARDS0701 RESET CN0702 12 12 CN0113 XRESET

IN7 F3 IC4601 DC CONTROL, RESET, LANC DRIVER, DRUM/CAPSTAN PWM DRIVER (22/23) PVDD8a PVDD8b M2 VOUT LX8a LX8bB6, A6 B5, A5

HP-150 BOARDCN0603 J652 LANC 3 3 CN0115 CN0119 LANC_DC 3

FP-788 FLEXIBLE BOARD37

PUI_BATT_XEXT O_FASTCHARGE O_INITCHARGE XPUDIO_SIO_IB

BATT/XEXT H2 FAST_CHARGE C2 INIT_CHARGE_ON C1 BATT_SIG A4

CN1007 LANC_DC

AI_BATTSENSE K6 AI_ACVSENSE J7 B4 XPUI_POWER_VTR_SW A3 XPUI_MODE_CAM_SW IC5001 HI CONTROL (21/23) XI_LANCPOWER_ON B1 XO_LANCON B5 O_SO_DO XO_SCK_DDD2, D1

IC4604 DC CONTROL (22/23)

VOUT

L4606

L4612

D_1.5V

IN8 C7 OUT11 R15 VB B1 L3 WAKE-UP M3 XCTL2L13, M13

MS-379 BOARD (1/2)CN8001 (1/2) BT901 LITHIUM BATTERY 12

FP-786 FLEXIBLE BOARD (1/2)12

CN1012 (1/2) VBATT

XLANC_PWR_ON XLANC_ON FR_EVER_SO, FR_EVER_SCK BATT_IN XCS_DD VTR_DD_ON

C1, D2, E4, E3

I_BATTIN A7 XO_CS_DD A6 O_VTRDDON E3

BPOWER (2/4) (PAGE 3-9)

XSYS_RST XDS_RESET

A8 XODO_SYSRST C8 XO_HIRST

VOUT3 B2 DIN VOUT2 B3 CLK N2 CS_OUT K13 LD APPL_SW1, CH6_SW, CTL1, CH9_SW1, CH9_SW2, CH10_SW1, CH10_SW2 VR P4C5, N12, N5, C10, C9, F13, G13

N_3.1V

L4625

SVDD PVDD S1 S2

VOUT A3

R4611

CP_-2.8V CAM_-1,0V ST_UNREG D_2.8V A_2.8V A_4.6V MT_5V CMOS_4.1V D_1.5V

B2 FB IC4602

STBY C2 -2.8V REG (22/23)

FPOWER (4/4) (PAGE 3-11)

C05 POWER (4/4) (PAGE 3-11)

XSYS_RST XDS_RESET

EVER_3.0V

P2 VRO


3-8

3-9. POWER BLOCK DIAGRAM (2/4)VC-500 BOARD (2/4)D_1.0V A_1.2V D_1.2V_HV D_1.2V_K D_1.5V D_1.8V


D_1.0V A_1.2V D_1.2V_HV D_1.2V_K D_1.5V D_1.8V D_2.5V D_2.8V A_2.8V D_2.5V D_2.8V A_2.8V D_1.5V A_1.2V D_1.2V_HV

EPOWER (1/4) (PAGE 3-8)

D_2.5V D_2.8V A_2.8V AU_2.8V D_3.3V A_4.6V AU_4.6V MT_5V CP_-2.8V N_3.1VL3201 L3202 L3203

A_4.6V IC2401 256M DDR-SDRAM (7/23) CP_-2.8V

L2201

FB2101

FB2102

FB2002

FB2104

FB2401

FB2103

L2102

L2104

L2105

L2101

L2003

L2001

IC3002Q3001 3.3V REG FB3001 L3004 L3005 L3001 L3002 L3006 FL3100 FL3101 FL3102

FB3401

FL3201

L3401

L2202

L2203

L2204

L2703

L2702

L2704

L2205

AUDIO AD/DA CONVERTER (14/23)

FB2201

L2002

BUFFER Q2101 - Q2107

J6 XRESTL D7 XRESETP

IC3001 VIDEO OUT, AUDIO IN/OUT (14/23)

IC3101F4 XRST

B4 RESET#

IC3201 HDMI TRANSMITTER (11/23)

IC3401 HDV/DV i.LINK INTERFACE (9/23)

XRST_IC_2701_DV G23 XRSTDV XRST_IC_2701_2 H23 XRST2 XRST_IC_2701_1 H24 XRST1 A23 JTRST J3 PLLRST

D16 ISRSTX

XRST_IC_2201

XRST_HDMI

XRST_LINK XRST_PHY

A_1.2V D_1.2V_HV D_1.2V_K D_1.5V D_1.8V D_2.5V D_2.8V A_2.8V N_3.1VFB1901

D_1.2V_HV D_1.2V_K D_1.5V D_1.8V

D_2.8VFB5201 FB5103

N_3.1V

FB5102

FB5105

FL1901

FB5106

IC5103FB4401

FB1701

FB1702

L1201

L1202

L1301

L1302

L1701

L1702

L1703

L1704

W17 MS_VCC_ON E3 CHIME_PWR_CONT

D13 XDS_RESET

AB4 XRST T4 PLLRST

IC1702 CAMERA SIGNAL PROCESSOR (3/23)

13 XRST

D6 RST

D6 RST

X1701

F2 XRST F4 XINIT

XRST_HDMI XRST_LINK XRST_PHY XRST_IC_2701_DV XRST_IC_2701_2 XRST_IC_2701_1 XRST_IC_2201 XRST_VTR

Y15 E20 D22 G2 B13 D13 E22 Y18 N22 F22

XRST_HDMI XDIA_INT XRST_PHY XRST_IC_2701 XRST_IC_2701_1 XRST_IC_2701_0 XRST_IC_2201 XRST_VTR XHDMI_DICN XREEL_HALL_ON

F2 XRST F4 XINIT

CLOCK GENERATOR (3/23)

256M SDRAM (5/23)

32M FLASH (18/23)

16M SDRAM (18/23)

128k EEPROM (19/23)

IC1801 CAMERA CONTROL (19/23)

B14 RST_IC_1801 F23 RST_IC_5703

IC1201 CDS, A/D CONVERTER (1/23)

IC1301 CDS, A/D CONVERTER (2/23)

FB5202

FB1802

OSCILLATOR DRIVE (17/23)

IC1701

IC1901

IC5202

IC5201

IC1802

IC4401 MECHA CONTROL (20/23)

IC5101 DS CONTROL, HI CONTROL (17/23)

XRST_VTR

BPOWER (1/4) (PAGE 3-8)

XSYS_RST XDS_RESET

XSYS_RST

XREEL_HALL_ON XRST_VTR CHIME_PWR_CONT

D17 XRST

HDMI SIGNAL PROCESSOR (10/23)

IC2701 HDV STREAM PROCESSOR, MUX/DEMUX, DV SIGNAL PROCESSOR (8/23)

IC2201 HDV-MPEG VIDEO ENCODER/DECODER, MPEG AUDIO SIGNAL PROCESSOR (6/23)

IC2001 COMPONENT OUT AMP (5/23)

IC2402 16M FLASH (7/23)

IC2101 BASE BAND SIGNAL PROCESSOR, DOWN CONVERTER, D/A CONVERTER (4/23)

L2103

GPOWER (3/4) (PAGE 3-10)

AU_4.6V

L2902

4 IN

OUT 3L2901

XRST_IC_1801 XRST_IC_5703_CPU

IC2904 2.8V REG (13/23)

XHDMI_DICN MS_VCC_ON XRST_IC_5703_CPU XRST_IC_1801

HPOWER (4/4) (PAGE 3-11)

IC2901 MIC AMP (13/23)

IC2902 MIC LEVEL CONTROL (13/23)

IC2903 VOLTAGE FOLLOWER (13/23)

05


3-9

3-10. POWER BLOCK DIAGRAM (3/4)VC-500 BOARD (3/4)N_8.5V


IF-155 BOARD (2/3)L3703 CN3701 20 EVF_VDD 1 CN0102 CN0103 19 EVF_VDD 19

BH-001 BOARDCN6003 CN6002 20 EVF_VDD 20

BL-015 BOARDCN5901 CN5902 2 COLOR EVF UNIT LCD902

A_4.6V

L3702 2

EP_4.6V

19

8

EP_4.6V

FB6003 8 2

EP_4.6V

D5901 (EVF BACKLIGHT) 2

A_2.8V

L3701 FB3701

IC3701 EVF DRIVER (12/23) CN1017 (2/2)

AFP-789 FLEXIBLE BOARD (2/2)2, 3EP_8.5V EP_4.6V EP_2.8V POWER (1/4) (PAGE 3-8)

D_2.8V

CN0118 (2/2)

PD-342 BOARDCN6001 CN0104 CN6004 FB6001 1 16 2 D_2.8V FB6002 10 CN6005 10 8 R6206 3 IC6202 LCD BACKLIGHT CONTROL A_4.6V 15 EP_8.5V EP_4.6V EP_2.8V 1 L6202 16 FB6201 2 Q6201, Q6202 10 CN0105 10 8 D_2.8V 15 TOUCH PANEL I/F L6201 IC6201 LCD DRIVER CN6202 L6203

N_8.5V EP_4.6V EP_4.6V A_2.8V

31, 32

Q6208, Q6211, Q6212

CN6205 17 11 VDDG VDD LCD901 2.7 inch WIDE COLOR LCD UNIT VSS

7, 8

POWER (1/4) (PAGE 3-8) D_2.8V

D_2.8V

20

D_2.8V

14

29, 30

D

22

12

7, 8

EP_4.6V

Q6207, Q6210

4, 5

EP_8.5V EP_2.8V

CSD 67 CP 48 BLON_P 21

15 D6205

6, 7

A_4.6V

27, 28

A_2.8V RP_4.6V

L4901 L4902

IC4901 REC/PB AMP (15/23)

9

A_4.6V

9

3

Q6203 - Q6206 LCD BACKLIGHT DRIVE D6206 - D6208 (BACKLIGHT)

CN0101

5, 6

A_4.6V CN6006

FP-784 FLEXIBLE BOARD3, 4D_2.8V IC801 OPEN/CLOSE DETECT

HI-078 BOARDIC_4601_13.5V VTR_UNREG MT_5V D_2.8V IC4801 DRUM/CAPSTAN/ LOADING MOTOR DRIVE (16/23) VH 17 VMR 3 34 XRESET R4812 CN4801 26 TAPE_LED_A MIC903 4PIN CONNECTOR S REEL SENSOR T REEL SENSOR 05 H901 H902 MR_VCC CN0207

N MECHANISM DECK (MDX-N220)CN4803 8 HE_VCC FG_VCC HU, HV, HW CAPSTAN FG D902 (TAPE LED)

3, 4

R204 - R206 D201 - D203 (CAMERA RECORDING)

XRST_VTR

GPOWER (2/4) (PAGE 3-9) CHIME_PWR_CONT

Q5110 - Q5112

L4801 12 Q4802 SENSOR_VCC R4801

25, 2621

CHIME_VDD

HALL_VCC

XREEL_HALL_ON


3-10

3-11. POWER BLOCK DIAGRAM (4/4)VC-500 BOARD (4/4)

( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.CM-077 BOARDCN1201 CAM_-1.0V CMOS_4.1V A_2.8V 26 27 31 30 32 A_-1.0V A_4.1V A_2.8V XSYS_RST VST_C_RESET A_-1.0V A_4.1V A_2.8V 15 IC6603 14 10 4 3.3V REG (3/3) IC6605 4 3.3V REG (3/3) IC6606 4 3 3 L6704 L6706 CN6601

CPOWER (1/4) (PAGE 3-8)

XSYS_RST XDS_RESET

HPOWER (2/4) (PAGE 3-9)

XRST_IC_1801 XRST_IC_5703_CPU XHDMI_DICN MS_VCC_ON CAM_-1.0V CMOS_4.1V A_2.8V MT_5V D_2.8V

L6702 L6705 L6707

IC6701 6M CMOS IMAGER (1/3)

CN1010 405, 6

12 MT_5V D_2.8V46, 47

CN5303 XRST_IC_1801 L5401 FB5401

IC6604 4 H11 XCLR IC5404 FOCUS/ZOOM/NF MOTOR DRIVE, ND FILTER DRIVE, IRIS DRIVE (1/4) 3 CN5301 Z_MR_VCC 19 F_MR_VCC 15 IC5403 ZOOM MOTOR NOISE FILTER (1/4) XSYS_RST VST_C_RESET 11 9 L7201 17 CRST IC7201 PITCH/YAW SENSOR AMP (2/3) SE7202 PITCH SENSOR LENS BLOCK SE7201 YAW SENSOR 2.8V REG (3/3) 3

10

4

48 L5301 50 4 IC5304 2.8V REG (4/4)

A_4.6V

2

A_4.6V

IC5402 ZOOM MOTOR NOISE FILTER (1/4)D_2.8V MT_5.0V A_4.6V

EC-001 BOARDCN53063, 4

CN53113, 4

A_4.6V L5701 IC5703 D_1.5V 3 D_1.5V 49 XRST_IC_5703_CPU XDS_RESET VST_C_RESET OPTICAL IMAGE STABILIZATION DRIVE (2/4) A6 XDL A7 RESET_N D5 CPU_PIO_0

PH5501 MANUAL FOCUS/ZOOM SENSOR

R5501


41 39 44

11 13 8

FPOWER (1/4) (PAGE 3-8) CN1012 (2/2) D_2.8V IC1001 2.9V REG (23/23) MS_VCC_ON 1 CE 4 VDD MS_VCC R8008 CN8004 VCC MEMORY STICK DUO

FP-786 FLEXIBLE BOARD (2/2)14 14

MS-379 BOARD (2/2)CN8001 (2/2) R8001 D8003 (MS ACCESS)

VOUT 3

1

1

9

IC3202 5V REG (11/23) XHDMI_DICN ST_UNREG CN32023, 4

FP-867 FLEXIBLE BOARD+5V POWER

1 CONT 6 VIN VOUT 4

CN001 18 HDMI OUT

R1027

CN1015 (2/2) 15

FP-785 FLEXIBLE BOARD (2/2)MODE_LED_VDD 4

IF-155 BOARD (3/3)CN0120 (2/2) CN0117 4 11

SP-048 BOARDCN0501 MODE_LED_VDD CN0502 3 6

MO-027 BOARDCN0504 R553 D558,D559 PLAY/EDIT D552 MEMORY D551 TAPE

05

R552

R551


3-11E

XCLR

FP-787 FLEXIBLE BOARD

LD-229 BOARD

1.8V REG (3/3)

3

4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS4-1. FRAME SCHEMATIC DIAGRAMS

FRAME SCHEMATIC DIAGRAM (1/2)

CN8103 USB CONNECTOR

IF-155 Board CN0106 (Page 4-2)

MS-379 BOARD (SIDE A)12 11

BT901 LITHIUM BATTERY26

HCPC (For Check)2 1


CN8002 CN8004 MEMORY STICK CONNECTOR BT901 BH8001 BATTERY HOLDER

Harness (MI-076)8

MS-379 BOARD (SIDE B)

2 1

7 8 1

CN8003

CN8102 CN81011 8 10 1

1

CN8001

26

US-014 BOARDFlexible flat cable (FFC-107)

26

1

CM-077 BOARD FP-867 FLEXIBLE BOARD20

CN001 HDMI OUT1 20 22 19 21 23

LENS BLOCKIF-155 Board CN0102 (Page 4-2)42

JFlexible flat cable (FFC-330)

I

1 41

CN6601

40

IF-155 Board CN0122 (Page 4-2)Flexible flat cable (FFC-332)

CN370120 1 26

CN10121

1

B

CN1006

16

IF-155 Board CN0110 (Page 4-2)Flexible flat cable (FFC-334)

1

15

CN1003

2

1

IC5202 (Not supplied)

CN3202

14

1

VC-500 BOARD (SIDE A)IF-155 Board CN0111 (Page 4-2)CN1009

VC-500 BOARD (SIDE B)

20

20

C

Flexible flat cable (FFC-335)

6

IC1802 (EEPROM)CN10101 2

51 50

1

CN1015

IC2402 (Not supplied)

1

39

33 32

2

CN4801

28 29

41

CN4803

CN1001

CN1017

1 2 1

1

CN1201

40 42 2 1 26 27 1 10 1 10

CN480216

CN4901

2 1

CN1007

38 39 1

EFP-788 FLEXIBLE BOARD


Harness (HN-047)1

1

FP-789 FLEXIBLE BOARDIF-155 Board CN0118 (Page 4-2)51 1 1

39 33

D33

1

20

1

FP-787 FLEXIBLE BOARD EC-001 BOARDCN53111 2 5 6



FP-032 FLEXIBLE BOARDVIDEO HEAD

A


1

18

M901 DRUM MOTOR Flexible flat cable (FFC-339)

LD-229 BOARD (SIDE B)CN53066 51 1 2 1

Harness (LI-062)

LD-229 BOARD (SIDE A)51 50 1


G

F


MM903 CAPSTAN MOTOR


M902 LOADING MOTOR

M

CN5307

M1

1 2 1 4

CN5301

2


1 2 1

CN5303

50 51

N MECHANISM DECK (MDX-N220)


4-1

FRAME (1/2)

FRAME SCHEMATIC DIAGRAM (2/2)1


CN05046 8 1

CN0505

CN02016 1

MO-027 BOARD

SP901 SPEAKER

HI-078 BOARD (SIDE B)Flexible flat cable (FFC-329) Flexible flat cable (FFC-336)

CN02078 1

LCD902 COLOR EVF UNIT

HI-078 BOARD (SIDE A) SP-048 BOARD14 13 1 2 7 8

CN0501

2 1

CN0502

CN5901

CN0401

BL-015 BOARD

21 20

1 2

MC-188 BOARD20

CN59021

J401 MIC (PLUG IN POWER)4

Flexible flat cable (FFC-337) Harness (IJ-001)


1

VC-500 Board CN3701 (Page 4-1)

Harness (IJ-002)

JHarness (BI-001)

JK-355 BOARD8

1 2

JS-033 BOARDCN07021 12 1

CN0701

4

2

3

1

4

1

2

3


BH-001 BOARD RE-038 BOARDCN08512115 1

IF-155 BOARDLD-229 Board CN5307 (Page 4-1) VC-500 Board CN1006 (Page 4-1)19 201

15 16

CN0103

20

1 2

CN0102

19 20

CN0122

A B

Harness (LI-062)

CN0101

2 1

CN6004

20


CN6003

CN0110

CN0107

2 1

15

Harness (RS-112)

8 7

10

1

Flexible flat cable (FFC-334) Harness (MI-075) Flexible flat cable (FFC-340)

2 1

1 2

1 2

CN0117

13 14

I H

VC-500 Board CN1003 (Page 4-1) MS-379 Board CN8002 (Page 4-1)

CN6002

CN6005 CN600712

CN0104

CN0105

1 2

14 13

12

10

CN0113

1

Harness (MI-076)

1 2

11 12

CN01061

J0703

J0701

J0702

CN0109

1

1

6

CN60061 5 2 6

CN0108

1

1

CN6001

22

1

CN0114

1 2

8

10

1

CN0116

CN01182 1 32 33

CN0112

CN0120


CN0111

C


9

2 1

Pr/Cr

Pb/Cb COPMPONENT OUT

Y

S VIDEO

VIDEO A/V OUT

L

AUDIO

R

4

CN0115

1


GHarness (DI-003)

VC-500 Board CN1015 (Through the FP-785 flexible board) (Page 4-1)

1

39

15 16

Harness (HP-147)

2

CN0119

38

1

1

18 17

2 1

6 5

6

CN0121


F

NS-022 BOARD6 5 2 1 6 5 2 1 12 11 2 1

PD-342 BOARD

CN0903

CN0902

CN0901

VC-500 Board CN1017 (Through the FP-789 flexible board) (Page 4-1)Harness (DI-005)

VC-500 Board CN1007 (Through the FP-788 flexible board) (Page 4-1)Harness (DI-004)

CN6202

DC-110 BOARD (SIDE B)1

CN0602

22

D

E

1 2


CN0601

1

1

CN6205

24

1

6

HP-150 BOARDCN06041

CN6201

2.7 INCH WIDE COLOR LCD UNIT

TOUCH PANEL

CONTROL SWITCH BLOCK (ZM90500)

CONTROL SWITCH BLOCK (PS90500)

CN0605 HDV/DV6

BA-008 BOARD

Harness (BD-058)

1

1

CN0603

LCD901

J652 LANC JACK

CN06523

10

J651 HEADPHONE JACK


SW

C


3

1

9

DC-110 BOARD (SIDE A)

CN0610 DC IN

4-2

FRAME (2/2)

4-2. SCHEMATIC DIAGRAMS (1/2)LinkCM-077 BOARD (1/3) (CMOS IMAGER) CM-077 BOARD (2/3) (PITCH/YAW SENSOR) CM-077 BOARD (3/3) (CONNECTOR, REG) VC-500 BOARD (1/23) (A/D CONVERTER 1) VC-500 BOARD (2/23) (A/D CONVERTER 2) VC-500 BOARD (3/23) (CAMERA SIGNAL PROCESS) VC-500 BOARD (4/23) (BASE BAND SIGNAL PROCESS) VC-500 BOARD (5/23) (SDRAM 1) VC-500 BOARD (6/23) (HDV-MPEG VIDEO ENCODE/DECODE) VC-500 BOARD (7/23) (SDRAM 2) VC-500 BOARD (8/23) (HDV STREAM PROCESS) VC-500 BOARD (9/23) (HDV/DV i.LINK INTERFACE) VC-500 BOARD (10/23) (HDMI SIGNAL PROCESSOR) VC-500 BOARD (11/23) (HDMI TRANSMITTER) VC-500 BOARD (12/23) (EVF DRIVE) VC-500 BOARD (13/23) (MIC AMP) VC-500 BOARD (14/23) (VIDEO OUT, AUDIO IN/OUT) VC-500 BOARD (15/23) (REC/PB AMP) VC-500 BOARD (16/23) (SERVO) VC-500 BOARD (17/23) (DS CONTROL, HI CONTROL) VC-500 BOARD (18/23) (SDRAM, FLASH) VC-500 BOARD (19/23) (CAMERA CONTROL) VC-500 BOARD (20/23) (MECHA CONTROL) VC-500 BOARD (21/23) (HI CONTROL) VC-500 BOARD (22/23) (DC/DC CONVERTER) VC-500 BOARD (23/23) (CONNECTOR) LD-229 BOARD (1/4) (LENS DRIVE) LD-229 BOARD (2/4) (OIS DRIVE) LD-229 BOARD (3/4) (Not Used) LD-229 BOARD (4/4) (REGULATOR, CONNECTOR) IF-155 BOARD (CONNECTOR) BH-001 BOARD (LCD SWITCH, CONNECTOR)

TO (2/2)

COMMON NOTE FOR SCHEMATIC DIAGRAMS


4-2. SCHEMATIC DIAGRAMS (2/2)TO (1/2)PD-342 BOARD (LCD DRIVE) US-014 BOARD (USB CONNECTOR) BL-015 BOARD (EVF BACKLIGHT) RE-038 BOARD (PANEL REVERSE) JK-355 BOARD (COMPONENT CONNECTOR) JS-033 BOARD (A/V CONNECTOR) HP-150 BOARD (LANC, HP, i.LINK CONNECTOR) MC-188 BOARD (MIC JACK) MS-379 BOARD (MS CONNECTOR) SP-048 BOARD (CONTROL SWITCH) MO-027 BOARD (CONTROL SWITCH) HI-078 BOARD (TALLY LED) EC-001 BOARD (MANUAL FOCUS/ZOOM SENSOR) NS-022 BOARD (CONNECTOR) BA-008 BOARD (BATTERY IN) DC-110 BOARD (DC IN, CHARGE LED) FP-867 FLEXIBLE BOARD (HDMI CONNECTOR) FP-784 FLEXIBLE BOARD (OPEN/CLOSE DETECT) FP-785 FLEXIBLE BOARD (EJECT SWITCH, IF-VC CONNECTION) FP-786 FLEXIBLE BOARD (MS-VC CONNECTION) FP-787 FLEXIBLE BOARD (LD-VC CONNECTION) FP-788 FLEXIBLE BOARD (VC-IF CONNECTION) FP-789 FLEXIBLE BOARD (VC-IF CONNECTION) FP-793 FLEXIBLE BOARD (REC, ZOOM SWITCH) CONTROL SWITCH BLOCK (ZM90500) CONTROL SWITCH BLOCK (PS90500) FP-228, FP-032, FP-031 FLEXIBLE

HVR-HD1000 V1

Documents

Transcript of HVR-HD1000 V1