Hpl technical specs
2
SL.NO PROPERTIES TEST METHOD ATTRIBUTES OF PERFORMANCE UNITS RESULTS(AS PER EN 438-6) EN-438 LAMINATE CLASSIFICATION EGS/EDS/EGF/EDF 1 1.1 Thicknes EN 438-2.5 Thickness tolerance mm 5 < T < 8 : +_ 0 ,4 1.2 Size EN 438-2.6 Length and Width mm .+10/-0 1.3 Straightness of edges EN 438-2.7 Streightness of edges mm/m <.1.5 1.4 Squareness EN438-2.8 Squareness mm/m <1.5 1.5 Flatness EN438-2.9 Flatness (measured on full-size sheet) mm/m 2.0< T < 6, 0 : 8 2 2.1 Flexural Modulus EN ISO 1.78 Stress Mpa > 9000 2.2 Flexural strengthg EN ISO 1.78 Stress Mpa > 80 2.3 Tensile strength EN ISO 527-2 Stress Mpa > 60 2.4 Density EN ISO 1183 Density gm/cm3 >1.35 2.5 Resistance to impact with large EN 438-2.21 Indent. Dia. 10 mm 2 < T<6 mm Drop Height min. >1400 Diameter ball Indent. Dia. 10 mm T >6 mm Drop Height min. >1800 2.6 Resistance to wet Conditions EN 438-2.15 Mass increase -2< T < 5mm max.% EGS/EDS- <7, EGS/EDF- <10 Mass increase - T > 5mm max.% EGS/EDS- <5, EGF/EDF- <8 High Pressure Laminates-STYLAM EXTERIOR CLADDING ---- TECHNICAL SPECIFICATIONS PHYSICAL PROPERTIES DIMENTIONAL PROPERTIES A10,Bldg 5,Akshay Mittal; Estate,Andheri East,Mumbai 59 T:+9122 4046 3100 E: [email protected] W:- http://leadsfacade.com
-
Upload
leads-facade -
Category
Design
-
view
229 -
download
7
Transcript of Hpl technical specs
SL.NO PROPERTIES TEST METHOD ATTRIBUTES OF PERFORMANCE UNITS RESULTS(AS PER EN 438-6)
EN-438 LAMINATE CLASSIFICATION EGS/EDS/EGF/EDF
1
1.1 Thicknes EN 438-2.5 Thickness tolerance mm 5 < T < 8 : +_ 0 ,4
1.2 Size EN 438-2.6 Length and Width mm .+10/-0
1.3 Straightness of edges EN 438-2.7 Streightness of edges mm/m <.1.5
1.4 Squareness EN438-2.8 Squareness mm/m <1.5
1.5 Flatness EN438-2.9 Flatness (measured on full-size sheet) mm/m 2.0< T < 6, 0 : 8
2
2.1 Flexural Modulus EN ISO 1.78 Stress Mpa > 9000
2.2 Flexural strengthg EN ISO 1.78 Stress Mpa > 80
2.3 Tensile strength EN ISO 527-2 Stress Mpa > 60
2.4 Density EN ISO 1183 Density gm/cm3 >1.35
2.5Resistance to impact with
largeEN 438-2.21
Indent. Dia. 10 mm 2 < T<6 mm Drop
Heightmin. >1400
Diameter ballIndent. Dia. 10 mm T >6 mm Drop
Heightmin. >1800
2.6Resistance to wet
ConditionsEN 438-2.15 Mass increase -2< T < 5mm max.% EGS/EDS- <7, EGS/EDF- <10
Mass increase - T > 5mm max.% EGS/EDS- <5, EGF/EDF- <8
High Pressure Laminates-STYLAM EXTERIOR CLADDING ---- TECHNICAL SPECIFICATIONS
PHYSICAL PROPERTIES
DIMENTIONAL PROPERTIES
A10,Bldg 5,Akshay Mittal; Estate,Andheri East,Mumbai 59 T:+9122 4046 3100 E: [email protected] W:- http://leadsfacade.com
2.6Resistance to wet
ConditionsEN 438-2.15 Appearance Rating >4
2.7Dimensional stability at
elevated temperatureEN438-2.17
Cumulative dimensional change -
2<T<5mmLongitudinal % < 0.40
Transversal % < 0.80
Cumulative dimensional change
T>5mmLongitudinal % < 0.30
Transversal % < 0.60
3
3.1Resistance to Climatic
ShockEN 438-2.19 Thermal Shock Resistance-Appearance Rating > 4
3.2Resistance to Artificial
WeatheringEN 438-2.29 contrast Grey scale rating > 3
WEATHER RESISTANCE REQUIREMENTS
The below are the Quality certificates we have for our range of High Pressure Laminates
A10,Bldg 5,Akshay Mittal; Estate,Andheri East,Mumbai 59 T:+9122 4046 3100 E: [email protected] W:- http://leadsfacade.com
