How to measuremorestextiles.com/media/how to measure.pdf · Measure the width of the window from...
Transcript of How to measuremorestextiles.com/media/how to measure.pdf · Measure the width of the window from...
Compliment the interior design of your costumer’s home with custom made window treatments
The entire look and feel of a room can change dramatically with the
addition of Made-to-Measure soft window treatments. Just by adding
these, you can create a luxurious, warm and comfortable feel
Made-to-Measure window treatments start with the correct measurement of the window. This guide is an overview on how to measure the different tre-atments, as well as some guidelines to help your costumers choose the right treatment for their window.
Since “Made-to-Measure curtains are made to your exact specifications, it is imperative that the measurements be made with the greatest of care.
If you are measuring the width and drop (length) of a window we would recommend taking at least three measurements at different points.
Windows are not always absolutely square - especially older windows - and therefore the width and length can vary.
Measure each window separately even when they appear to be the same size. Double check all measurements for accuracy.
Watch out for window sills, heaters and other obstacles. Curtains and blinds have to hang free.
Whether you are measuring for rods, tracks,
curtains or blinds, always use a metal measuring
tape - never use fabric as it can stretch and
give an inaccurate reading.
How to measure ?
How to measure ?
Understanding your window
To understand how to measure, you need to know a little about your windows and decide where you would like to place yous window furnishings.
Ways to hang curtains or blinds
Inside Mount installationInside mounting is where the curtains or blind are installed inside the window frame
Outside Mount installationA outside mounting is where the curtains or blind are installed on or above the window frame.
window sill
Frame
inside mount
outside mount
Framed window Unframed window Recessed windowtimber or molding surround
- Start by looking at the window to decide where you want your curtains to go.- If it is a recessed window, do you want the curtains to hang within the recess or outside the frame?- Remember that headings like tab top, rod pocket and grommets only work on a rod.
Tracks & RodsWe recommend installing the tracks or rods before measuring for curtains. It makes a more accurate measurement.
Tracks - outside mountMeasure the width of the window from corner to corner
Sometimes you will need to add or deduct inches/cm’s from the measurements. It is easy if you follow the steps.
Add to the measurement
To maximize your outside view and you have available space, we recommend adding an additional 8 ” / 20 cm to both sides to allow the curtains to stack back.
If you only have space on one side of the window, we advise adding an additio-nal 16“ / 40 cm to allow the complete curtain to stack back on one side.
Measuring
Tracks - inside mountMeasure the inside width of the window from left to right.
Rods - outside mountMeasure the width across the top of the window from left to right. Place the rods at least 4” / 10 cm above the window.
Deduct from the measurement
Deduct 0.4” / 1 cm from the measurement to allow the curtain to hang free.
To maximize your view, add an additional 8” / 20 cm on both sides to allow your curtains to stack back.
Add to the measurement
Be aware:Rods are not suitable for inside
mount installation.
- Start by looking at the window to decide where you want your curtains to go.- If it is a recessed window, do you want the curtains to hang within the recess or outside the frame?- Remember that headings like tab top, rod pocket and grommets only work on a rod.
Tracks & RodsWe recommend installing the tracks or rods before measuring for curtains. It makes a more accurate measurement.
Tracks - outside mountMeasure the width of the window from corner to corner
Sometimes you will need to add or deduct inches/cm’s from the measurements. It is easy if you follow the steps.
Add to the measurement
To maximize your outside view and you have available space, we recommend adding an additional 8 ” / 20 cm to both sides to allow the curtains to stack back.
If you only have space on one side of the window, we advise adding an additio-nal 16“ / 40 cm to allow the complete curtain to stack back on one side.
Measuring
How to measure ?
How to measure your curtains
After you have installed your rod or track, you are ready to measure for curtains. Measurements vary by heading. See below how to measure for each separate heading. When ordering, please specify if the curtains have to be made as a set, or if the curtain is to stack in one direction
Width:Measure the total width of your track or rod (excluding the finials). For all hea-dings we recommend adding ½” per 40 inches slack ensure a nice closure.
Length:Measurements of the length are dependable on the heading.
1. If you prefer your curtains to hang below the sill, we re commend ad ding an additional 4”/10 cm in length.
2. With our state-of-the-art hook system, you will still have the ability to adjust the hook higher, or lower should you so require. (approximately 2 inches)
Tips:
For pleated curtains on a trackMeasure from the top of the track to the sill or floor.
For pleated curtains on a rodMeasure from the bottom of the curtain ring to the sill or floor.
Deduct 0.8”/2 cm from the shortest measurement to allow the curtain to hang free
Deduct 0.8”/2 cm from the shortest measurement to allow the curtain to hang free
How to measure ?
double pleat on a track
pleated on a rod
For rod pocket curtains on a rodMeasure from the top of the rod to the sill or floor.
Add the desired header to the measurement
Deduct 0.8”/2 cm from the shortest measurement to allow the curtain to hang free
For grommet curtains on a rodMeasure from the top of the rod to the sill or floor.
Add the desired header to the measurement Our standard header is set to 0.8”/2cm. If youchoose, you can alter the measurement.
Deduct 0.8”/2 cm from the shortest measurement to allow the curtain to hang free
Sheers installed under drapes
should be at least 0.4”/1 cm
shorter.
How to measure ?
For tap top curtains on a rodMeasure from the top of the rod to the sill or floor.
Deduct 0.8”/2 cm from the shortest measurement to allow the curtain to hang free
grommets
rod pocket
tab tops
Width:Measure the width at the top of the window from outer cormer to outer corner of the frame.
Length:Measure the length from the top of the moulding to the bottom of the sill or the floor. Measure both sides of the window.
Measuring blinds
To determine if a blind is more suitable for an inside or outside mount, be aware of the following:
• Recess depth– blinds need a mimimum of 1.8”/4.5 cm for the headrail• Are there any obstructions like window handles or spindels?• The window frame used• Special window types – tilted, sliding doors etc• When you are working with a cornered window, for example a bay or bow window, we advise you to work with an inside mount.
Sometimes you will need to add or deduct from measurements. It is easy if you follow the steps.
Blinds - outside mount framed window
Add a minimum of 2”/5 cm on both sides to block light.
Top: Add at least 4”/10 cm to the measurement to ensure proper fixing of the blind.
Optional: When the window is not to the floor, extend the length with an additional 6”/15 cm below the window to block light when closed.
Blinds - outside mount without frame
Width:Measure the width of the window from outer corner to outer corner.
Length:Measure the drop from the top of the window to the bottom of the sill or the floor. Measure both sides of the window.
Add a minimum of 4”/10 cm to both sides to block light
Top: Add at least 4”/10 cm to the measurement to ensure proper fixing of the blind.Optional: When the window is not to the floor, extend the length with an additional 6”/15 cm below the window to block light when closed.
inside mount outside mount
How to measure ?
Width:Measure the width of the window at 3 points and provide the smallest measurement.
Blinds - inside mount application
Deduct ¼” /0.5 cm from the measure-ment to allow for clearance. We will make the exact size you give us.
If there are large variations in your width or
length measurements, we recommend using an
outside mount.
Length:Measure the length at 3 points and provide the smallest measurement.
Deduct ¼” /0.5 cm from the measure-ment to allow for clearance. We will make the exact size you give us.
How to measure ?