OWNER’S MANUAL

FOR THE

HOSE REELS

HR25/50/100

25-100m

C-Dax Ltd PO Box 1010, 145 Harts Road

Tiritea, Palmerston North Ph: 06 354 6060 Fax: 06 355 3199

E-Mail: sales@c-dax.co.nz www.c-dax.co.nz

.2

SAFETY PRECAUTIONS

HOSE REELS 25-100M

AN IMPORTANT MESSAGE FOR OWNERS & OPERATORS OF

C-Dax ATTACHMENTS/ACCESSORIES Be warned of the dangers of loading your vehicle in excess of its carrying capacity. It is important to understand that any loads or attachments whether fastened to or placed on a vehicle will alter the stability or handling characteristics of that vehicle. Spray tanks or other equipment must be filled only to a level where the gross weight is within the load limit of the vehicle. Safety is a primary concern in the design, manufacture, sale, and use of spray tanks and other equipment. As manufacturers of spray tanks and other equipment we want to confirm to you, our customers, our concern for safety. We take this opportunity to remind you about the simple, basic and common sense rules of safety when using spray tanks and other equipment. Failure to follow these rules can result in severe injury or death to operators and bystanders.

It is essential that everyone involved in the assembly, operation, transport, maintenance and storage of this equipment be aware, concerned, prudent and properly trained in safety. This also applies to equipment that is loaned or rented to someone who has not read the owner’s manual and is not familiar with the operation of application equipment.

NEVER EXCEED THE LOAD LIMIT CAPACITY OF THE TRACTOR,ATV OR OTHER VEHICLE.

ALL TRACTOR, ATV AND TRAILED EQUIPMENT TYRES SHOULD BE INFLATED TO MANUFACTURERS RECOMMENDED OPERATING PRESSURES.

PLEASE NOTE THAT FILLING THE SPRAY TANK OR OTHER EQUIPMENT COMPLETELY AND OR THE ATTACHMENT OF ADDITIONAL EQUIPMENT TO THE TRACTOR OR ATV MAY EXCEED THE TRACTOR OR ATV’S MAXIMUM LOAD CAPACITY AND IT IS NOT RECOMMENDED TO EXCEED MANUFACTURERS GUIDELINES

CARGO SHOULD BE PROPERLY DISTRIBUTED AND SECURELY ATTACHED.

REDUCE SPEED WHEN CARRYING CARGO OR PULLING A TRAILER OR TRAILED APPLICATION EQUIPMENT AND ALLOW GREATER DISTANCE FOR BRAKING.

NEVER ALLOW ANYONE TO RIDE ON YOUR SPRAYER OR OTHER EQUIPMENT. ALWAYS FOLLOW THE INSTRUCTIONS IN THE OWNER’S VEHICLE MANUAL FOR CARRYING

CARGO OR PULLING A TRAILER.

PROPER MAINTENANCE IN LINE WITH MANUFACTURER’S RECOMMENDED MAINTENANCE PROCEDURES IS ESSENTIAL.

BEFORE APPLYING CHEMICALS, READ THE LABEL OF THE CHEMICAL MANUFACTURER OR SUPPLIER FOR PERSONAL PROTECTIVE EQUIPMENT AND OPERATE AS RECOMMENDED.

THE SAFETY OF ALL CHEMICALS USED IN AGRICULTURE IS UNDER THE JURISDICTION OF A GOVERNMENT AGENCY, IE N.Z. MINISTRY FOR THE ENVIRONMENT; USA ENVIRONMENTAL

PROTECTION AGENCY. FURTHER LOCAL GOVERNMENT OR STATE LAWS MAY APPLY.

WARNING To reduce the chance of VEHICLE instability, exercise EXTREME care while spraying on a slope or hillside.

Cautions, Warnings and Notes.

Throughout this document, text has been highlighted as warnings, cautions and notes.

Warnings are mandatory instructions. Failure to comply with these instructions may result in injury or damage.

Cautions are advisory. Failure to comply may result in poor operation or premature failure.

Notes are to assist with convenient operation of the equipment.

3

SAFETY

Before attempting to install or operate the equipment, read and understand the manual thoroughly. Failure to comply with this instruction constitutes improper use and will invalidate the warranty.

Before using your pesticide, STOP, Read The Label

Mixing pesticides is a most dangerous time as it involves handling the concentrated material. For toxic compounds, use protective clothing such as overalls, hat, gloves, boots and respirator. When using concentrated sprays, full protection is necessary. When using diluted sprays, wear a hat, long-sleeved cotton overalls, and boots. If you use pesticides regularly, it is a good idea to always wear a respirator to avoid cumulative effect. Other protection may be required. Check the label. It may have specific directions for the particular chemical. Protective clothing should be properly cared for. Rinse heavily contaminated clothes in the open before washing in the laundry. Wash and dry protective clothing every day, but keep them separate from other washing. Respirators need special care. Clean your respirator after spraying. Use soapy water then rinse and allow drying completely before storing in a clean plastic bag. Replace canisters in respirator after eight hours use.

4

C-Dax

HOSE REELS

HR25/50/100

25-100M

OWNERS MANUAL (Pt.No 2400-6300 Issue 12, April 2018)

TABLE OF CONTENTS

2 Safety Precautions

4 Contents

5 Introduction

Description

Specifications

Order Information

Warranty

7 Hose Reel Installation HR25 Mounting

Top Mounting to 500L Flat Deck and Trailed Sprayers Rear Mounting to 500L Flat Deck and Trailed Sprayers

Three Point Linkage frames Plumbing

9 Theory of Operation

Operation

10 Maintenance After Use Routinely Annually Filters

11 Replacement Parts

5

INTRODUCTION CONGRATULATIONS on the purchase of your new C-Dax Hose Reel. You join the many thousands of New Zealand and overseas farmers who have recognised the remarkable usefulness and uniqueness of these C-Dax Hose Reels.

DESCRIPTION

The C-Dax Hose Reels are range of robust hose reels with models from 25M to 100M hose capacity. The reels are manufactured of sturdy steel construction, with a plastic or steel hose drum, and all models are finished with zinc plated steel components and high-pressure PVC hoses. All reels are fitted with brass hose connectors as standard. There are several reel models in the range;

HR25; A 25 metre reel, with plastic drum, suitable for mounting on an ATV or a C-Dax spray unit,

complete with 10mm or 8.5mm hose. HR50; A 50 metre reel, with plastic drum, suitable for mounting on an ATV or a C-Dax spray unit,

complete with 10mm hose. HR100; An all steel construction hose reel, suitable for mounting on a C-Dax spray unit, complete

with 10mm hose.

SPECIFICATIONS

(Specifications subject to change without notice)

Length ; HR25 Up to 25M of 10mm hose Up to 30M of 8.5mm hose

HR50 Up to 50M of 10mm hose HR100 Up to 100M of 10mm hose Construction; All Models Steel Frame with brass hose fittings HR25/HR50 Plastic drum HR100 Steel Drum

ORDER INFORMATION

HR25

HR25 with vertical mounting bracket suitable for attaching to ATV or vehicle with vertical face

Order HR25 No Hose Pt.No. 1057

HR50

HR50 suitable for mounting on a flat surface or to a vehicle Order HR50 No Hose Pt.No.1058 HR50H10(50)HG2 with 50M and Hand Gun Pt.No.1063

HR100 HR100 suitable for mounting on a flat surface or to a vehicle

Order HR100 No Hose Pt.No. 1059 HR100H10(100)HG2 with 100M and Hand Gun Pt.No. 1064

6

WARRANTY

1 WARRANTY AND LIABILITY

Use of the equipment

1.1 You must satisfy yourself as to the suitability of the equipment for your intended use(s) of the

equipment.

Your relationship with the retailer

1.2 Where you consider you have a warranty claim (or any other claim) in relation to the equipment,

you must contact the retailer who sold you the equipment, not C-Dax directly. The retailer is

responsible for liaising with C-Dax in respect of your claim.

Warranty

1.3 C-Dax warrants to the original purchaser that the equipment is sold free from defects in materials

and workmanship for a period of 12 months from date of first retail sale (6 months from date of

first retail sale if the equipment is sold in the U.K.) subject to the terms set out below.

1.4 C-Dax will at its option repair or replace the defective equipment (or part of the equipment) or

notify the retailer of the equipment to refund the purchase price for such defective equipment to

you in the event of a breach of this warranty, subject to the terms set out below.

Liability

1.5 Except for the warranty set out in clause 1.2 above, all warranties and representations (including

those expressed or implied by law) in respect of the equipment or advice relating to the equipment

provided to you by C-Dax are excluded to the extent permitted by law.

1.6 Notwithstanding anything else in this manual, C-Dax’s maximum liability to you (in the event that

such liability exists) in respect of any breach of warranty, any matter set out in this manual, or for

defective equipment or advice relating to the equipment provided is limited at C-Dax’s option to:

(a) repairing or replacing the equipment (or part of the equipment); or

(b) notifying the retailer of the equipment to refund the price for the equipment paid by you.

1.7 Notwithstanding anything else in this manual, in no event will C-Dax be liable, whether in contract,

tort (including negligence) or otherwise:

(a) where you have altered or modified the equipment, misused or misapplied the equipment, or

the equipment has been subjected to any unusual, excessive or non-recommended use,

service or handling (including as set out in this manual);

(b) where the equipment is not transported, stored, handled or used in accordance with any

directions given by C-Dax (or the retailer) to you (including as set out in this manual);

(c) where the equipment:

(i) has been subject to neglect, accident or hireage, or the damage arises from fair wear

and tear, battery damage or chemical attack;

(ii) has been built to a customer’s specifications; or

(iii) has been dismantled, repaired or serviced other than by an authorised service agent

of C-Dax;

(d) for loss or damage caused by any factors beyond C-Dax’s control; or

(e) for any loss of profit or revenue, or for any special, indirect, incidental or consequential

damage, loss or injury of any kind suffered by you.

7

1.8 Where C-Dax elects to repair or replace the equipment it will use reasonable endeavours to do so

as soon as practicable but will not be liable for any delay in doing so.

1.9 You agree that the transactions entered into between you and the retailer (and C-Dax) are for the

purposes of trade and that, having regard to all relevant circumstances of the transactions, it is fair

and reasonable that the provisions of the Consumer Guarantees Act 1993 (NZ) do not apply to

those transactions to the fullest extent permitted by law.

HOSE REEL INSTALLATION

WARNING To prevent equipment failure and overloading, it is not recommended to fit the reel directly to an ATV.

NOTE The QS upright bars can be adjusted in 50mm increments on the hose reel frame.

HR25 Mounting Mounting to Flat Surface; Fit the HR25 mounting bracket to a flat surface using the M8x40 bolts and p clamps supplied (the mounting plate may be used as a backing plate). Fit the hose reel into the mounting bracket and adjust to the required height. Mounting to ATV carrier; Fit mounting bracket and mounting plate to either side of the ATV carrier tubing, using the M8x40 bolts and nuts supplied. Fit the hose reel into the mounting bracket and adjust to the required height.

Mounting to top of 400L Flat Deck and Trailed Sprayers (Older spray units only)

Fit hose reel to top of tank straps using M8x25 Bolts and nuts supplied. Bolt Holes

8

Mounting to rear of, 400L/500L Flat Deck and 400L/500L Trailed Sprayers Fit crossbars to hose reel using M8x40 bolts and nuts. Fit hose reel and crossbars to the Boom Supports at the required height using M10x65 bolts and nuts supplied. Cross Bars

Mounting to Three Point Linkage Frames Mounting HR50 & HR100 to rear of 3PL frame; Fit crossbars to hose reel using M8x40 bolts and nuts supplied. Fit hose reel and crossbars to the rear of the 3PL frame, at the required height, using M10x50 bolts, nuts and clamping plates supplied.

Delivery Hose Plumbing Connect the supply 2m hose to the brass inlet elbow and secure with the hose clamps provided.

Plumbing (12V Pump) Connecting to a Sprayer with an existing spray gun; Cut the sprayer output line from the pump in an easily accessible position, and install the quick release valve. Connect the delivery hose to the hose reel, cut the hose to a length so that it can be connected to the quick release valve using the 10mm male hose shank connector. Connect the remainder of the sprayer output line to the existing spray gun, to the remaining male hose shank connector.

Direct Connecting to Pump; Remove pump cover from sprayer. Connect the delivery hose to the hose reel, cut the hose to a length so that it can be connected, using the hose clamps provided, to the output elbow on the pump without kinking. Run the pump with water and check for leaks before refitting the pump cover. Tighten clamps further if required. Refit the pump cover making sure not to over tighten the pump cover screws, as this may strip the hole of its thread.

Plumbing (PTO or Engine Driven Pump) Connect the Hose Reel delivery line to a spare outlet port on the sprayer pressure regulator, secure with hose clamps provided. Extra regulator outlet ports are available (depending on specification).

9

THEORY OF OPERATION Spray fluid is placed in the tank where it is drawn through a suction filter and pumped to a control valve. The excess flow from the valve is returned to the tank via the bypass hose. Fluid at a nominal pressure of 3-25 bar is pumped to the spray gun via the hose reel. Pulling the trigger on the spray gun may control the amount of fluid, distance, pattern and size of droplet transferred to the target, depending on the model of spray gun used. Adjusting the nozzle on the spray gun may also control the pattern and droplet size, depending on the spray gun used.

OPERATION

With water in the spray tank; Unwind the required length of hose from the reel. Open the dump valve on the regulator, and screw the pressure control knob fully open (counter clockwise). Turn on the pump,

-12V sprayers; Switch labelled ‘PUMP’ on the switch box -PTO sprayers; PTO lever on tractor -Engine sprayers; Pull start or electric start on engine

Ensure hoses and lines are free of kinks and blockages, and let fluid re-circulate to the tank. Close dump valve on regulator. Allow time for the air to be expelled from the hoses and lines. Open a valve, operate the spray gun, and adjust the tip for the required spray pattern. Screw the control knob in (clockwise) until the desired spraying pressure is reached. Water should flow evenly out of the spray gun tip. The nozzle will form the droplets, thus creating the spray. Shut down procedure; Open the dump valve on the regulator, and screw the pressure control knob fully open (counter clockwise). Proceed with cleaning if tank is empty. Turn off pump.

CAUTION Prolonged exposure of chemicals to tanks and spraying systems may cause them to prematurely fail. It is recommended to empty the tank and flush the system three times, with fresh water, at the end of spraying.

10

MAINTENANCE

After Use At the end of spraying, flush the system three times with fresh water. Finish with a final rinse using C-Dax Neutralise rinsing solution. Remove the strainer basket under the lid of the sprayer, rinse and refit. Remove the main filter element, clean and replace, ensuring that the filter bowl ‘O’ ring is in place, and the bowl nut is tight. Clean the outside of the sprayer to remove any spray residue.

Routinely

Check the spray tip patterns for wear, replace if necessary. Lubricate any moving parts. Check spray hoses for kinks or damage, replace if necessary.

Annually

Replace spray tips

Filters

Your Hose Reel System is fitted with two-stage filtration consisting of:

a) Filter basket at the tank inlet, and b) Suction filter between the tank and pump.

Check all filters after the first four hours of use, then at the end of each spraying session, more regularly depending on the water supply and chemicals used.

11

REPLACEMENT PARTS

The following parts are replacements for C-Dax hose reels. Please order by part number: Item: Part number: Delivery Hose-40 Bar-8.5mm 4100-0008 (Order Hose Per Metre) Delivery Hose-40 Bar-10mm 4100-0010 (Order Hose Per Metre) Spray Gun HG2 4000-3910 HR25 Reel Bare 1057 HR50 Reel Bare 1058 HR100 Reel Bare 1059

.12

1058 – Hose Reel 50m

13

1059 – Hose Reel 100m

14

1057 – Hose Reel 25m