HL System solutions
Transcript of HL System solutions
71,5
50 164299 DN
50
133
108
33
380 x 180503 x 303
304 x 104
15 ~
5. Barrier-free showers
HL System solutions
5
42
HL53
HL053WS
HL540I
HL531
HL52
HL50F
43
Barrier-free showers nowadays are very popu-lar to end-users. The advantages are obvious:Real and optical gain of space, individual design of the shower area, and now also a wide range of barrier-free shower solutions in every price segment. In case of installation of barrier-free showers, it can be observed, that the practice is far away from the theory, whatsoever. There are many interfaces, where the instalment can go wrong and therefore the bathroom users expectations are not fulfilled; because of wrong consultation, because of a lack of coordination between construction company, installer, tiler… In order to prevent this failures it is recommen-ded to draw attention to certain aspects, such as following:
▲Installation heightEspecially in case of bathroom renovation, the installer has the problem of low floor heights - this leads to low drainage systems. Please do not forget, that for all tiled shower spaces a slope of minimum 2% is needed and has to be added to the drain height, when calculating!
▲CapacityCalculation of the required minimum drain capacity: Capacity of the shower fitting + 20%!The test procedure for the determination of the drain capacity is described in EN 1253-2; in this standard the nominal capacity is valid with a water height of 20mm above the grate or cover of the drain.
▲Connection to the waterproofingTiled showers are most endangered areas, concerning the penetration of moisture into the floor (and wall) construction (according ÖNORM B 2207 danger class W4). Since tiles and tile glue are not regarded as a permanent sealing, a waterproofing has to be applied below the tiles. Most endangered spot is the transition from drain to the sealing compound. Therefore high quality drains are equipped with flanges, which care for the tight sealing in this area. Also these drains should be able, to drain off leakage water, which is staying below the tiles (secondary water drainage).
▲Stench trapAccording to standard EN 12056-2 stenchtraps must be installed inside of the buildings.Every stench trap has to have water seal of atleast 5 cm height in order to prevent stench,
▲Selection of the drain system:Point drainage Linear drainage
▲Advantages of point drainage:
o Easy and long term experienced installationo Low priceo Less construction height, as the drain position is mostly in the middle and not at the end of the shower areao Individual choice of the drain position according to the tile pattern, perfect for diagonal tiling
▲Advantages of linear drainage:
o Easy preparation of the screed slope (only in one direction)o Perfect for large tileso Installation close to the wall avoids the overflow of water into the rest of the bathroomo High end design
rising into the building. In case of vacuum in the drainage system, these 5 cm water prevent from being sucked out by the vacuum. In case of lower floor heights (renovation) the sealing height in the trap could be less than 5 cm, if the trap is equipped with an additional mechanical odour barrier. HL shower drains are provided with its proven and reliable ”Primus”- system. This systemincludes both water trap and a mechanicalodour barrier. A floating body closes the siphon, when the water inside the trap has evaporated. For proper water drainage it is important to have an adequate ventilation of the pipe system. If the drain position is more than 4 m away from the down pipe, then this side wastepipe must be ventilated in accor-dance with EN 12056-2. In this case, the most economical solution is the installation of the vent-pipe HL905N.
▲Coordination at the building siteUsually three different kind of craftsmen work on the completion of a barrier-free shower:Screed layer, plumber and tiler. Therefor a good cross-over communication between these craftsmen is needed. For this purpose we recommend, to establish a central planning authority (planner, architect, ...).
▲DesignHL is offering different kinds of covers in diffe-rent colours. Therefor the final decision has to be taken in accordance with the end-user of the bathroom.
HL System solutions for barrier-free showers
Basic information for planning and execution
44
HL531 shower channel „Primus Line”
Tile glueTiles
Hydro insulation Sealing tape
Adhesive
Concrete HL531 Drain
Screed
Impact noise insulation
HL50WShower channel made of stainless steel, wall-side installation
HL50Fshower channel made of stainless steel, installation in the surface
HL Barrier-free showers – Sectional drawings
TilesButyle tapeWaterproofingTile glue
WaterproofingTile glueTilesSealing tape
Floor screed
Impact noise insulation
Concrete floor
Insulating tape
Support angle
Sound absorbing tape
PlasterboardDouble covering
Floor screed
Impact noise insulation
Concrete floor
WaterproofingSealing tapeSealing tapeTile glue
Tiles
Sound absorbing leg
HL50W.0 Drain
HL50F.0 Drain
HL540/541Shower drain„Primus Drain /Primus blue”
HL540/541 Shower drain
Impact noise insulationSound proofing pad HL6200
Tile glueTiles
Waterproofing
Concrete floor
Floor screed
HL50W
HL50F
HL540/541
HL531
45
HL053S(M)(P)
HL053WS
HL Barrier-free showers – Sectional drawings
HL53„In | Floor“ Shower channel
HL510NCFloor drain with polymer concrete collar
HL510N-3020Floor drain with tilable frame
WaterproofingTile glue
Tiles
Embankment
Coating
Embankment
Impact noise insulation
Concrete
Tile glueTiles
Sound proofing pad HL6200
Concrete
Floor screed
Impact noise insulation
Concrete
HL53 Shower channel
HL510NC Floor drain
Floor screed
HL510N-3020 + HL83.M Floor drain
Floor screed
Impact noise insulation
Waterproofing
HL53 Shower channel
Screed
Water proofing
Tiles Tile glue
Concrete floor
EmbankmentSound insulation
HL053WS „Wall“ Shower channel
HL510NC
HL510N-3020
HL053WS
HL53
46
AA
BC
HL Barrier-free showers – Installation manual HL53
1. Position drain body and fix it to the raw concrete ceiling
2. Adjust drain body to the height - then level it long- and broadside
3. Switch drain nozzle to one of the three possible sides, connect it to the drain pipe and check whether it‘s water proof
5. Remove building protection and any pollution, then install sealing kit
6. Use building protection, install waterproof seal, paint both sides and make sure to check drying time.
4. Level screed by keeping a minimum slope of 2% to the building protection
7. Stainless steel - position cover, cut it to the length and adjust height step by step
8. Fix to the ground by using tile adhesive 9. Stainless steel - adjust cover vertically by pushing down the adhesive bed; the inlaying cross sloap ensures reliable drainage
10. Remove positioning profile and install odour trap 11. Removable stainless steel - use cover - ready! 12. A: Waterproof Seal B: Tile adhesive C: Ceramic tiling
47
HL Barrier-free showers – Installation manual HL531
1. Measure shower area; Adjust shower drain in length by shortening both sides of the shower block
2. Preparation of the surface (flat surface), apply adhesive on the surface
3. Position shower channel in the adhesive layer next to the wall. Check its horizontal position
5. Insert the sound insulation and and thermal insulation 6. Insert screed with a minimum of 2% slope to the edge of the EPS-panel
4. Connect the drain with pipe and make leak test
7. Apply liquid waterproofing on both sides of the sealing foil
8. Attach sealing tapes, seal the entire shower area 9. Set tiles up to the edge of the protection cover
10. Remove protection cover and fill silicone into the surrounding gaps
48
HL Barrier-free showers - Installation manual HL540/541
1. Define outlet position, set the stencil in direction to the outlet pipe and mark the holes for the drilling.
2. Drill holes 3. Fix the drain body with fixing angles on the floor and connect to the pipe.
5. Insert floor screed and create a slope to the drain by minimum 2%.
6. After the floor screed is dry, cut the salient nozzle with a saw (or cutting disc).
4. Adjust the decline of the pipe by using the angles and level the drain body.
7. Insert the sealing kit, turn the protection cover and insert it again.
8. Apply waterproofing in the whole shower area and on (and under) the sealing kit, seal the edges with sealing tapes.
9. Insert the extension, if necessary, cut the extension.
10. Adjust the extension by turning to the tile layout (360° turnable), lay the tiles.
11. Remove the protection cover and insert the grate. 12. Ready
49
aa
Primus blue trap - function
„Primus blue“ - the new HL hybrid trap for shower and floor drains - works mechanic and hydraulic. It protects from smell, no matter if there is under pressure, over pressure or if the water inside is evaporated.
When the water from the shower runs throuth the trap, the valve disc opens.
When the valve disc is opened, the water may pass the trap as usual.
Underpressure from the sewer: The weight of the valve disc together with the water inside the trap protects from getting sucked out.
Overpressure in the sewer: The valve disc is pressed against the valve seat, so no smell may get out. A further advantage: the trap is save against back flow.
if the water inflow is stopped, the valve disc closes, the water stays inside the trap.
Should the water inside the trap be evaporated, e.g. caused by a floor heating, the mechanic trap protects from bad smell
50
HL050.8E
HL050.5ENHL050N.1E
HL050.0EN
2 Stk. HL050.2EN
HL50F.0 Shower channel made of stainless steel, installation in the surface, HEIGHT 110 MM!
Data
Capacity 600 – 1300 mm length = 0,8 l/s1400 – 2100 mm length = 1,4 l/s
Material Stainless steel 1.4301/PPOutlet dimension DN50 with ball-jointHeight 110 mmStandard EN 1253Height of seal water 50 mmAdditional information
removable stench trap, with 5cm surrounding sand-coated flange for a save connection to the under-tile waterproofing. The frameless design makes it possible, to choose border bars, fitting to the tiles and enables under-tile leakage water, to flow into the trap.
Including Sound absorbing height adjustable levelling legs, 2 pieces of edge trim jigs, 2 pieces of tiling gauges
HL Barrier-free showers – Products – Data
When using ceramic tiles we recommend to produce an individual frame made of tiling profiles.
HL-No. Material Dimen-sion
length LX length LY Capacity Weight EAN Piece/package
HL50F.0/60 Stainless steel DN50 600 mm 0,8l/s 2261 g +024599 1HL50F.0/70 Stainless steel DN50 700 mm 0,8l/s 2488 g +024612 1HL50F.0/80 Stainless steel DN50 800 mm 0,8l/s 2729 g +024636 1HL50F.0/90 Stainless steel DN50 900 mm 0,8l/s 2937 g +024650 1HL50F.0/90.2 Stainless steel 2 x DN50 900 mm 200 mm 1,4l/s 3194 g +032433 1HL50F.0/100 Stainless steel DN50 1000 mm 0,8l/s 3224 g +024674 1HL50F.0/100.2 Stainless steel 2 x DN50 1000 mm 300 mm 1,4l/s 3480 g +032440 1HL50F.0/110 Stainless steel DN50 1100 mm 0,8l/s 3525 g +024698 1HL50F.0/110.2 Stainless steel 2 x DN50 1100 mm 300 mm 1,4l/s 3782 g +032457 1HL50F.0/120 Stainless steel DN50 1200 mm 0,8l/s 3760 g +024711 1HL50F.0/120.2 Stainless steel 2 x DN50 1200 mm 400 mm 1,4l/s 4017 g +032464 1HL50F.0/130 Stainless steel DN50 1300 mm 0,8l/s 3966 g +024735 1HL50F.0/130.2 Stainless steel 2 x DN50 1300 mm 400 mm 1,4l/s 4150 g +032471 1HL50F.0/140 Stainless steel 2 x DN50 1400 mm 500 mm 1,4l/s 5840 g +030545 1HL50F.0/150 Stainless steel 2 x DN50 1500 mm 500 mm 1,4l/s 6120 g +030569 1HL50F.0/160 Stainless steel 2 x DN50 1600 mm 600 mm 1,4l/s 6260 g +030583 1HL50F.0/170 Stainless steel 2 x DN50 1700 mm 600 mm 1,4l/s 6600 g +030606 1HL50F.0/180 Stainless steel 2 x DN50 1800 mm 700 mm 1,4l/s 6820 g +030620 1HL50F.0/190 Stainless steel 2 x DN50 1900 mm 700 mm 1,4l/s 7060 g +030644 1HL50F.0/200 Stainless steel 2 x DN50 2000 mm 800 mm 1,4l/s 7240 g +030668 1HL50F.0/210 Stainless steel 2 x DN50 2100 mm 800 mm 1,4l/s 7560 g +030682 1
HL50F.0
51
HL050.11E
HL050.8E
2 Stk. HL050.2EN
HL050.10E
HL050N.1E
HL50FF.0 Shower channel made of stainless steel, installation in the surface (flat version), HEIGHT 90 MM!
Data
Capacity 600 – 1300 mm length = 0,7 l/s1400 – 2100 mm length = 1,2 l/s
Material Stainless steel 1.4301/PPOutlet dimension DN50 with ball-jointHeight 90 mmHeight of seal water 30 mmAdditional information
removable stench trap, with 5cm surrounding sand-coated flange for a save connection to the under-tile waterproofing. The frameless design makes it possible, to choose border bars, fitting to the tiles and enables under-tile leakage water, to flow into the trap.
Including Sound absorbing height adjustable levelling legs, 2 pieces of edge trim jigs, 2 pieces of tiling gauges
When using ceramic tiles we recommend to produce an individual frame made of tiling profiles.
HL-No. Material Dimen-sion
length LX length LY Capacity Weight EAN Piece/package
HL50FF.0/60 Stainless steel DN50 600 mm 0,7l/s 2261 g +029761 1HL50FF.0/70 Stainless steel DN50 700 mm 0,7l/s 2488 g +029778 1HL50FF.0/80 Stainless steel DN50 800 mm 0,7l/s 2729 g +029785 1HL50FF.0/90 Stainless steel DN50 900 mm 0,7l/s 2937 g +029792 1HL50FF.0/90.2 Stainless steel 2 x DN50 900 mm 200 mm 1,2l/s 3135 g +035717 1HL50FF.0/100 Stainless steel DN50 1000 mm 0,7l/s 3224 g +024834 1HL50FF.0/100.2 Stainless steel 2 x DN50 1000 mm 300 mm 1,2l/s 3422 g +035724 1HL50FF.0/110 Stainless steel DN50 1100 mm 0,7l/s 3525 g +024858 1HL50FF.0/110.2 Stainless steel 2 x DN50 1100 mm 300 mm 1,2l/s 3723 g +035731 1HL50FF.0/120 Stainless steel DN50 1200 mm 0,7l/s 3760 g +024872 1HL50FF.0/120.2 Stainless steel 2 x DN50 1200 mm 400 mm 1,2l/s 3958 g +035748 1HL50FF.0/130 Stainless steel DN50 1300 mm 0,7l/s 3966 g +024896 1HL50FF.0/130.2 Stainless steel 2 x DN50 1300 mm 400 mm 1,2l/s 4164 g +035755 1HL50FF.0/140 Stainless steel 2 x DN50 1400 mm 500 mm 1,2l/s 5840 g +033362 1HL50FF.0/150 Stainless steel 2 x DN50 1500 mm 500 mm 1,2l/s 6120 g +033379 1HL50FF.0/160 Stainless steel 2 x DN50 1600 mm 600 mm 1,2l/s 6260 g +033386 1HL50FF.0/170 Stainless steel 2 x DN50 1700 mm 600 mm 1,2l/s 6600 g +033393 1HL50FF.0/180 Stainless steel 2 x DN50 1800 mm 700 mm 1,2l/s 6820 g +033409 1HL50FF.0/190 Stainless steel 2 x DN50 1900 mm 700 mm 1,2l/s 7060 g +033416 1HL50FF.0/200 Stainless steel 2 x DN50 2000 mm 800 mm 1,2l/s 7240 g +033423 1HL50FF.0/210 Stainless steel 2 x DN50 2100 mm 800 mm 1,2l/s 7560 g +033430 1
HL50FF.0
52
HL050.8E
2 Stk. HL050.2EN
HL050.12E
HL050.13E
HL050N.1E
HL50FU.0 Shower channel made of stainless steel, installation in the surface (extra flat), HEIGHT 68 MM!
Data
Capacity 600 - 1300 mm length = 0,46 l/s1400 - 2100 mm length = 0,82 l/s
Material Stainless steel 1.4301/PPOutlet dimension DN50Height 68 mmStandard EN 1253Height of seal water 24 mmAdditional information
Removable stench trap, with 5 cm surrounding sand coated flange for a save connection to the under-tile waterproofing. The frameless design makes it possible, to choose border bars, fitting to the tiles and enables under-tile leakage water, to flow into the trap.
Including Sound absorbing height adjustable levelling legs, 2 pieces of edge trim jigs, 2 pieces of tiling gauges.
When using ceramic tiles we recommend to produce an individual frame made of tiling profiles.
HL-No. Material Dimen-sion
length LX length LY Capacity Weight EAN Piece/package
HL50FU.0/60 Stainless steel DN50 600 mm 0,46 l/s 2261 g +033904 1HL50FU.0/70 Stainless steel DN50 700 mm 0,46 l/s 2488 g +033911 1HL50FU.0/80 Stainless steel DN50 800 mm 0,46 l/s 2729 g +033928 1HL50FU.0/90 Stainless steel DN50 900 mm 0,46 l/s 2937 g +033935 1HL50FU.0/90.2 Stainless steel 2 x DN50 900 mm 200 mm 0,82 l/s 3194 g +035762 1HL50FU.0/100 Stainless steel DN50 1000 mm 0,46 l/s 3224 g +033942 1HL50FU.0/100.2 Stainless steel 2 x DN50 1000 mm 300 mm 0,82 l/s 3481 g +035779 1HL50FU.0/110 Stainless steel DN50 1100 mm 0,46 l/s 3525 g +033959 1HL50FU.0/110.2 Stainless steel 2 x DN50 1100 mm 300 mm 0,82 l/s 3782 g +035786 1HL50FU.0/120 Stainless steel DN50 1200 mm 0,46 l/s 3760 g +033980 1HL50FU.0/120.2 Stainless steel 2 x DN50 1200 mm 400 mm 0,82 l/s 4017 g +035793 1HL50FU.0/130 Stainless steel DN50 1300 mm 0,46 l/s 3966 g +033997 1HL50FU.0/130.2 Stainless steel 2 x DN50 1300 mm 400 mm 0,82 l/s 4140 g +035809 1HL50FU.0/140 Stainless steel 2 x DN50 1400 mm 500 mm 0,82 l/s 5840 g +034000 1HL50FU.0/150 Stainless steel 2 x DN50 1500 mm 500 mm 0,82 l/s 6120 g +034017 1HL50FU.0/160 Stainless steel 2 x DN50 1600 mm 600 mm 0,82 l/s 6260 g +034024 1HL50FU.0/170 Stainless steel 2 x DN50 1700 mm 600 mm 0,82 l/s 6600 g +034031 1HL50FU.0/180 Stainless steel 2 x DN50 1800 mm 700 mm 0,82 l/s 6820 g +034048 1HL50FU.0/190 Stainless steel 2 x DN50 1900 mm 700 mm 0,82 l/s 7060 g +034055 1HL50FU.0/200 Stainless steel 2 x DN50 2000 mm 800 mm 0,82 l/s 7240 g +034062 1HL50FU.0/210 Stainless steel 2 x DN50 2100 mm 800 mm 0,82 l/s 7560 g +034079 1
HL50FU.0
53
HL050.5EN
HL050N.1E
HL050.8E
HL050.4E
2 Stk. HL050.2EN
HL050.0EN
HL50W.0 Shower channel made of stainless steel, installation wall-side, HEIGHT 110 MM!
Data
Capacity 600 – 1300 mm length = 0,8 l/s1400 – 2100 mm length = 1,4 l/s
Material Stainless steel 1.4301/PPOutlet dimension DN50 with ball-jointHeight 110 mmStandard EN 1253Height of seal water 50 mmAdditional information
removable stench trap, with 5cm surrounding sand-coated flange for a save connection to the under-tile waterproofing. The frameless design makes it possible, to choose border bars, fitting to the tiles and enables under-tile leakage water, to flow into the trap.
Including Sound absorbing height adjustable levelling legs, 2 pieces of edge trim jigs, 2 pieces of tiling gauges
When using ceramic tiles we recommend to produce an individual frame made of tiling profiles.
HL-No. Material Dimen-sion
length LX length LY Capacity Weight EAN Piece/package
HL50W.0/60 Stainless steel DN50 600 mm 0,8l/s 2409 g +024759 1HL50W.0/70 Stainless steel DN50 700 mm 0,8l/s 2655 g +024773 1HL50W.0/80 Stainless steel DN50 800 mm 0,8l/s 2965 g +024797 1HL50W.0/90 Stainless steel DN50 900 mm 0,8l/s 3248 g +024810 1HL50W.0/90.2 Stainless steel 2 x DN50 900 mm 200 mm 1,4 l/s +032495 1HL50W.0/100 Stainless steel DN50 1000 mm 0,8l/s 3462 g +024834 1HL50W.0/100.2 Stainless steel 2 x DN50 1000 mm 300 mm 1,4 l/s +032488 1HL50W.0/110 Stainless steel DN50 1100 mm 0,8l/s 3769 g +024858 1HL50W.0/110.2 Stainless steel 2 x DN50 1100 mm 300 mm 1,4 l/s +032501 1HL50W.0/120 Stainless steel DN50 1200 mm 0,8l/s 4082 g +024872 1HL50W.0/120.2 Stainless steel 2 x DN50 1200 mm 400 mm 1,4 l/s +032518 1HL50W.0/130 Stainless steel DN50 1300 mm 0,8l/s 4283 g +024896 1HL50W.0/130.2 Stainless steel 2 x DN50 1300 mm 400 mm 1,4 l/s +032525 1HL50W.0/140 Stainless steel DN50 1400 mm 500 mm 1,4l/s 6200 g +030385 1HL50W.0/150 Stainless steel DN50 1500 mm 500 mm 1,4l/s 6480 g +030408 1HL50W.0/160 Stainless steel DN50 1600 mm 600 mm 1,4l/s 6780 g +030422 1HL50W.0/170 Stainless steel DN50 1700 mm 600 mm 1,4l/s 6960 g +030446 1HL50W.0/180 Stainless steel DN50 1800 mm 700 mm 1,4l/s 7200 g +030460 1HL50W.0/190 Stainless steel DN50 1900 mm 700 mm 1,4l/s 7450 g +030484 1HL50W.0/200 Stainless steel DN50 2000 mm 800 mm 1,4l/s 7920 g +030507 1HL50W.0/210 Stainless steel DN50 2100 mm 800 mm 1,4l/s 8020 g +030521 1
HL50W.0
54
HL050.11E
HL050.10E
HL050N.1E
HL050.8E
HL050.4E
2 Stk. HL050.2EN
HL50WF.0 Shower channel made of stainless steel, installation wall-side (flat version), HEIGHT 90 MM!
Data
Capacity 600 – 1300 mm length = 0,7 l/s1400 – 2100 mm length = 1,2 l/s
Material Stainless steel 1.4301/PPOutlet dimension DN50 with ball-jointHeight 90 mmHeight of seal water 30 mmAdditional information
removable stench trap, with angled bar at the back, 5cm surrounding sand-coated flange for a save connection to the under-tile water-proofing. The frameless design makes it possible, to choose border bars, fitting to the tiles and enables under-tile leakage water, to flow into the trap.
Including Sound absorbing height adjustable levelling legs, butyl tape for a waterproof connection to the wall, tape for sound disconnection, 2 pieces of edge trim jigs, 2 pieces of tiling gauges
When using ceramic tiles we recommend to produce an individual frame made of tiling profiles.
HL-No. Material Dimen-sion
length LX length LY Capacity Weight EAN Piece/package
HL50WF.0/60 Stainless steel DN50 600 mm 0,7 l/s 2409 g +029716 1HL50WF.0/70 Stainless steel DN50 700 mm 0,7 l/s 2655 g +029723 1HL50WF.0/80 Stainless steel DN50 800 mm 0,7 l/s 2965 g +029587 1HL50WF.0/90 Stainless steel DN50 900 mm 0,7 l/s 3248 g +029594 1HL50WF.0/90.2 Stainless steel 2 x DN50 900 mm 200 mm 1,2 l/s +035663 1HL50WF.0/100 Stainless steel DN50 1000 mm 0,7 l/s 3462 g +029730 1HL50WF.0/100.2 Stainless steel 2 x DN50 1000 mm 300 mm 1,2 l/s +035670 1HL50WF.0/110 Stainless steel DN50 1100 mm 0,7 l/s 3769 g +029747 1HL50WF.0/110.2 Stainless steel 2 x DN50 1100 mm 300 mm 1,2 l/s +035687 1HL50WF.0/120 Stainless steel DN50 1200 mm 0,7 l/s 4082 g +029754 1HL50WF.0/120.2 Stainless steel 2 x DN50 1200 mm 400 mm 1,2 l/s +035694 1HL50WF.0/130 Stainless steel DN50 1300 mm 0,7 l/s 4283 g +029709 1HL50WF.0/130.2 Stainless steel 2 x DN50 1300 mm 400 mm 1,2 l/s +035700 1HL50WF.0/140 Stainless steel DN50 1400 mm 500 mm 1,2 l/s 6200 g +033447 1HL50WF.0/150 Stainless steel DN50 1500 mm 500 mm 1,2 l/s 6480 g +033454 1HL50WF.0/160 Stainless steel DN50 1600 mm 600 mm 1,2 l/s 6780 g +033461 1HL50WF.0/170 Stainless steel DN50 1700 mm 600 mm 1,2 l/s 6960 g +033478 1HL50WF.0/180 Stainless steel DN50 1800 mm 700 mm 1,2 l/s 7200 g +033485 1HL50WF.0/190 Stainless steel DN50 1900 mm 700 mm 1,2 l/s 7450 g +033492 1HL50WF.0/200 Stainless steel DN50 2000 mm 800 mm 1,2 l/s 7920 g +033508 1HL50WF.0/210 Stainless steel DN50 2100 mm 800 mm 1,2 l/s 8020 g +033515 1
HL50WF.0
55
HL050N.1E
HL050.8E
HL050.4E
2 Stk. HL050.2EN
HL050.12E
HL050.13E
HL50WU.0 Shower channel made of stainless steel, installation wall-side (extra flat), HEIGHT 68 MM!
Data
Capacity 600 - 1300 mm length = 0,46 l/s1400 - 2100 mm length = 0,82 l/s
Material Stainless steel 1.4301/PPOutlet dimension DN50Height 68 mmHeight of seal water 24 mmAdditional information
Removable stench trap, with 5cm surrounding sand coated flange and angled bar at the back for a save connection to the under-tile waterproofing. The frameless design makes it possible, to choose border bars, fitting to the tiles and enables under-tile leakage water, to flow into the trap.
Including Sound absorbing height adjustable levelling legs, butyl tape for a waterproof connection to the wall, tape for sound disconnection, 2 pieces of edge trim jigs, 2 pieces of tiling gauges.
When using ceramic tiles we recommend to produce an individual frame made of tiling profiles.
HL-No. Material Dimension length LX length LY Capacity Weight EAN Piece/package
HL50WU.0/60 Stainless steel DN50 600 mm 0,46 l/s 2409 g 1HL50WU.0/70 Stainless steel DN50 700 mm 0,46 l/s 2655 g 1HL50WU.0/80 Stainless steel DN50 800 mm 0,46 l/s 2965 g 1HL50WU.0/90 Stainless steel DN50 900 mm 0,46 l/s 3248 g 1HL50WU.0/90.2 Stainless steel 2 x DN50 900 mm 200 mm 0,82 l/s 1HL50WU.0/100 Stainless steel DN50 1000 mm 0,46 l/s 3462 g 1HL50WU.0/100.2 Stainless steel 2 x DN50 1000 mm 300 mm 0,82 l/s 1HL50WU.0/110 Stainless steel DN50 1100 mm 0,46 l/s 3769 g 1HL50WU.0/110.2 Stainless steel 2 x DN50 1100 mm 300 mm 0,82 l/s 1HL50WU.0/120 Stainless steel DN50 1200 mm 0,46 l/s 4082 g 1HL50WU.0/120.2 Stainless steel 2 x DN50 1200 mm 400 mm 0,82 l/s 1HL50WU.0/130 Stainless steel DN50 1300 mm 0,46 l/s 4283 g 1HL50WU.0/130.2 Stainless steel 2 x DN50 1300 mm 400 mm 0,82 l/s 1HL50WU.0/140 Stainless steel DN50 1400 mm 500 mm 0,82 l/s 6200 g 1HL50WU.0/150 Stainless steel DN50 1500 mm 500 mm 0,82 l/s 6480 g 1HL50WU.0/160 Stainless steel DN50 1600 mm 600 mm 0,82 l/s 6780 g 1HL50WU.0/170 Stainless steel DN50 1700 mm 600 mm 0,82 l/s 6960 g 1HL50WU.0/180 Stainless steel DN50 1800 mm 700 mm 0,82 l/s 7200 g 1HL50WU.0/190 Stainless steel DN50 1900 mm 700 mm 0,82 l/s 7450 g 1HL50WU.0/200 Stainless steel DN50 2000 mm 800 mm 0,82 l/s 7920 g 1HL50WU.0/210 Stainless steel DN50 2100 mm 800 mm 0,82 l/s 8020 g 1
HL50WU.0
56
HL050N.1E
HL050.5EN
HL050.8E
HL050N.1E
HL050.5EN HL050.8E
HL50FV.0 Shower channel made of stainless steel, installation in the surface, with vertical outlet
Data
Capacity 600 - 1300 mm length = 0,8 l/s 1400 - 2100 mm length = 1,4 l/s
Material Stainless steel 1.4301/PPOutlet dimension DN50 verticalHeight See techn. drawingStandard EN 1253Height of seal water 50 mmAdditional information
Removable stench trap, with 5cm surrounding sand-coated flange for a save connection to the under-tile waterproofing. The frameless design makes it possible, to choose border bars, fitting to the tiles and enables under-tile leakage water to flow into the trap.
Including Sound absorbing height adjustable levelling legs, 2 pieces of edge trim jigs, 2 pieces of tiling gauges
HL-No. Material Dimension Length LX
Length LY
Capacity Weight EAN Piece/package
50FV.0/60 Stainless steel DN50 600 mm 0,8 l/s 3760 g +03792 150FV.0/70 Stainless steel DN50 700 mm 0,8 l/s 3840 g +03777 150FV.0/80 Stainless steel DN50 800 mm 0,8 l/s 4060 g +03793 150FV.0/90 Stainless steel DN50 900 mm 0,8 l/s 4100 g +03773 150FV.0/100 Stainless steel DN50 1000 mm 0,8 l/s 4850 g +03794 150FV.0/110 Stainless steel DN50 1100 mm 0,8 l/s 5010 g +03795 150FV.0/120 Stainless steel DN50 1200 mm 0,8 l/s 5210 g +03796 150FV.0/130 Stainless steel DN50 1300 mm 0,8 l/s 5280 g +03797 150FV.0/140 Stainless steel DN50 1400 mm 500 mm 1,4 l/s 8250 g +03798 150FV.0/150 Stainless steel DN50 1500 mm 500 mm 1,4 l/s 8500 g +03799 150FV.0/160 Stainless steel DN50 1600 mm 600 mm 1,4 l/s 8650 g +03800 150FV.0/170 Stainless steel DN50 1700 mm 600 mm 1,4 l/s 8900 g +03801 150FV.0/180 Stainless steel DN50 1800 mm 700 mm 1,4 l/s 9130 g +03802 150FV.0/190 Stainless steel DN50 1900 mm 700 mm 1,4 l/s 9380 g +03803 150FV.0/200 Stainless steel DN50 2000 mm 800 mm 1,4 l/s 9620 g +03804 150FV.0/210 Stainless steel DN50 2100 mm 800 mm 1,4 l/s 9870 g +03805 1
2 pcs. HL050.2EN
When using ceramic tiles we recommend to produce an individual frame made of tiling profiles.
2 pcs. HL050.2EN
HL50FV.0
57
LX -1004018
34018 LX -100
40
18 LX -10011,5
HL050.8E
HL050S Cover plate „Standard“, made of stainless steel - for shower channels
Data
Material Stainless steel 1.4301 Height Usage for floorings from 2 – 16 mm
including tile glueLoad classification K3 (300 kg)
HL050D Cover plate „Design“, made of stainless steel - for shower channels
Data
Material Stainless steel 1.4301 brushed finish
Height Usage for floorings from 5 – 19 mm including tile glue
Load classification K3 (300 kg)
HL050I Cover plate ”Individuell”, made of stainless steel - for shower channels
Data
Material Stainless steel 1.4301 brushed finish
Height Usage for floorings from 16 – 30 mm including tile glue
Load classification K3 (300 kg)Additional information
with recess for customers individual floor finish
HL050.3EN Adjustment screws for the precise cover height
Data
Material PPRecommended for For the adapting of the cover plates
to higher floorings, like natural stones
HL-No. Material Weight EAN Piece/package050.3EN PP 296 g +025862 1
Shower channel
Requ. quant. of sets
60 – 70 cm 280 – 110 cm 3
120 – 130 cm 4140 – 180 cm 5190 – 210 cm 6
Used cover plate
Adjustable in height
Standard 15 – 29 mm
Design 18 – 32 mm
Individuell 29 – 43 mm
HL-No. Material length LX -100 Weight EAN Piece/package050S/60 Stainless steel 500 mm 410 g +024919 1050S/70 Stainless steel 600 mm 490 g +024933 1050S/80 Stainless steel 700 mm 583 g +024957 1050S/90 Stainless steel 800 mm 672 g +024971 1050S/100 Stainless steel 900 mm 746 g +024995 1050S/110 Stainless steel 1000 mm 830 g +025015 1050S/120 Stainless steel 1100 mm 900 g +025039 1050S/130 Stainless steel 1200 mm 992 g +025053 1
HL-No. Material length LX -100 Weight EAN Piece/package050S/140 Stainless steel 1300 mm 1074 g +029891 1050S/150 Stainless steel 1400 mm 1156 g +029914 1050S/160 Stainless steel 1500 mm 1238 g +029938 1050S/170 Stainless steel 1600 mm 1320 g +029952 1050S/180 Stainless steel 1700 mm 1402 g +029976 1050S/190 Stainless steel 1800 mm 1484 g +029990 1050S/200 Stainless steel 1900 mm 1566 g +030026 1050S/210 Stainless steel 2000 mm 1648 g +030040 1
HL-No. Material length LX -100 Weight EAN Piece/package050D/60 Stainless steel 500 mm 872 g +025077 1050D/70 Stainless steel 600 mm 1041 g +025091 1050D/80 Stainless steel 700 mm 1260 g +025114 1050D/90 Stainless steel 800 mm 1395 g +025138 1050D/100 Stainless steel 900 mm 1550 g +025152 1050D/110 Stainless steel 1000 mm 1757 g +025176 1050D/120 Stainless steel 1100 mm 1954 g +025190 1050D/130 Stainless steel 1200 mm 2116 g +025213 1
HL-No. Material length LX -100 Weight EAN Piece/package050D/140 Stainless steel 1300 mm 2322 g +603007 1050D/150 Stainless steel 1400 mm 2528 g +603009 1050D/160 Stainless steel 1500 mm 2734 g +603011 1050D/170 Stainless steel 1600 mm 2940 g +603013 1050D/180 Stainless steel 1700 mm 3146 g +603015 1050D/190 Stainless steel 1800 mm 3352 g +603017 1050D/200 Stainless steel 1900 mm 3558 g +603019 1050D/210 Stainless steel 2000 mm 3764 g +603021 1
HL-No. Material length LX -100 Weight EAN Piece/package050I/60 Stainless steel 500 mm 766 g +025237 1050I/70 Stainless steel 600 mm 914 g +025251 1050I/80 Stainless steel 700 mm 1060 g +025275 1050I/90 Stainless steel 800 mm 1213 g +025299 1050I/100 Stainless steel 900 mm 1412 g +025312 1050I/110 Stainless steel 1000 mm 1488 g +025336 1050I/120 Stainless steel 1100 mm 1723 g +025350 1050I/130 Stainless steel 1200 mm 1855 g +025374 1
HL-No. Material length LX -100 Weight EAN Piece/package050I/140 Stainless steel 1300 mm 2003 g +030224 1050I/150 Stainless steel 1400 mm 2151 g +030248 1050I/160 Stainless steel 1500 mm 2299 g +030262 1050I/170 Stainless steel 1600 mm 2447 g +030286 1050I/180 Stainless steel 1700 mm 2595 g +030309 1050I/190 Stainless steel 1800 mm 2743 g +030323 1050I/200 Stainless steel 1900 mm 2891 g +030347 1050I/210 Stainless steel 2000 mm 3039 g +030361 1
HL050D
HL050I
HL050.3EN
HL050S
58
HL53 - In| Floor system family
In | Floor design cover HL053M - massive stainless steel, brushed; length: from 80cm to 150cm
In | Floor design cover HL053P - massive stainless steel, polished; length: from 80cm to 150cm
In | Floor design cover HL053S - stainless steel, brushed; length: 90cm, 100cm and 120cm
„Wall“ standard cover HL053WS - stainless steel, brushed;Length: 90cm, 100cm or 120cm
In | Floor short channel HL052M stainless steel brushed
In | Floor short channel HL052P stainless steel polished
„Wall“ design cover „duo-wall“ HL053M.2 - massive stainless steel brushed;Length: from 130cm to 200cm
„Wall“ design cover „duo-wall“ HL053P.2 - massive stainless steel polished;Length: from 130cm to 200cm
59
HL53 - In| Floor system family
Drain body HL53KHeight: 90mmFlow rate: 0,8l/s
Drain body HL53KFHeight: 65mmFlow rate: 0,5l/s
Drain body „Duo wall“ HL53K.2Height: 90mmFlow rate: 1,45l/s
Drain body „Duo wall“ HL53KF.2Height: 65mmFlow rate: 0,86l/s
Drain body HL53KVVertical outletFlow rate: 1l/s
60
HL53K
HL53KF
HL53K
HL53KF
HL053.2E
HL053.3E
HL053N.1E
HL053.2E
HL053.4E
HL053N.1E
HL53K „In|Floor“ drain body for shower channel or short shannel, MIN. HEIGHT 90 MM !
Data
Capacity 20 mm above drain level: 0,8l/s10 mm above drain level: 0,6l/s
Material PPOutlet DN50Height 90 - 250 mm adjustableStandard EN 1253Trap (water height) 50 mmFits to HL053S, HL053WS, HL053M(P),
HL052M(P) Additional information
Incl. removable trap and flexible waterproofing membrane.
Installation Installation wallside or in the surface. Please see movie www.hl.at
Data
Capacity 20 mm above drain level: 0,45l/s10 mm above drain level: 0,5l/s
Material PPOutlet DN40Height 65 - 250 mm adjustableStandard EN 1253Trap (water height) 30 mmFits to HL053S, HL053WS, HL053M(P),
HL052M(P) Additional information
Incl. removable trap and flexible waterproofing membrane.
Installation Installation wallside or in the surface. Please see movie www.hl.at
HL-No. Material Dimension Weight EAN Piece/package53K PP DN50 1336 g +041244 1
HL-No. Material Dimension Weight EAN Piece/package53KF PP DN40 1250 g +041251 1
HL53KF „In|Floor“ flat drain body for shower channel or short shannel, MIN. HEIGHT 65 MM !
HL53K
HL53KF
61
HL53K.2
HL53KF.2
HL53KVHL53KV
HL053.2E
HL053.2E
HL053.4E
HL053.3E
HL053N.1E
HL053N.1E
HL053.2E
HL053.6E
HL053N.1E
HL53K.2 HL53KF.2
HL53K.2 „Wall“ DUO drain body for shower channel HL053M(P).2, HEIGHT 90MM!
HL53KF.2 „Wall“ DUO flat drain body for shower channel HL053M(P).2, HEIGHT 65MM!
Data
Capacity 20 mm above drain level: HL53K.2=1,45l/s; HL53KF.2=0,86l/s10 mm above drain level: HL53K.2=0,9l/s; HL53KF.2=0,8l/s
Material PPOutlet HL53K.2: 2 x DN50
HL53KF.2: 2 x DN40Installation height HL53K.2: 90 - 250 mm
adjustable HL53KF.2: 65 - 250 mm adjustable
Standard EN 1253Siphon HL53K.2: 50mm water trap
HL53KF.2: 30mm water trapFits to HL053M.2, HL053P.2Additional information
incl. removable water traps, 2 flexible waterproof membranes and fixing legs; installation only close to the wall;
Installation Only close to the wall
HL-No. Material Dimension Weight EAN Piece/packageHL53K.2 PP 2 x DN50 2950 g +047802 1HL53KF.2 PP 2 x DN40 2500 g +047819 1
HL53KV „In|Floor“ vertical drain body for shower channel or short channel
Data
Capacity 20 mm above drain level: 0,9l/s10 mm above drain level: 1,0l/s
Material PPOutlet DN50Installation height
30 - 131 mm adjustable
Standard EN 1253Siphon 50mm water trapFits to HL053S, HL053WS, HL053M(P),
HL052M(P) Additional information
incl. removable water trap, polimer concrete collar with steel grid (only HL53KVC) and flexible waterproof membrane; installation in the shower surface or close to the wall. Incl. 4 adjustable fixing legs
Installation In the surface of the shower or close to the wall
HL-No. Material Dimension Weight EAN Piece/packageHL53KV PP DN50 1500 g +047154 1
HL53K.2
HL53KF.2
HL53KV
62
HL053
HL053S HL053S.1E
Data
Material Stainless steel V2A (1.4301)massive 6mm
Please see chart Please see chartLoad classification K3 - max. 300 kgFits to HL53K(F), HL53KV(C), HL53K(F)CAdditional information
In combination with drain body HL53K(F), drainage strip with multiple precision slopeusage for: floor tiles 10 - 32 mmand wall tiles 12 - 24 mm(incl. tile glue)
Included Installation accessories and lot cover
Installation Installation wallside or in the surface.
HL-No. Material Dimension Surface Weight EAN Piece/package053M/80 Stainless steel V2A 800 x 55 x 6 mm matt 3650 g +041428 1053M/85 Stainless steel V2A 850 x 55 x 6 mm matt 3800 g +041275 1053M/90 Stainless steel V2A 900 x 55 x 6 mm matt 3950 g +041282 1053M/95 Stainless steel V2A 950 x 55 x 6 mm matt 4100 g +041299 1053M/100 Stainless steel V2A 1000 x 55 x 6 mm matt 4300 g +041305 1053M/110 Stainless steel V2A 1100 x 55 x 6 mm matt 4550 g +041312 1053M/120 Stainless steel V2A 1200 x 55 x 6 mm matt 4700 g +041329 1053M/130 Stainless steel V2A 1300 x 55 x 6 mm matt 4850 g +041336 1053M/140 Stainless steel V2A 1400 x 55 x 6 mm matt 5150 g +041343 1053M/150 Stainless steel V2A 1500 x 55 x 6 mm matt 5450 g +041350 1053P/80 Stainless steel V2A 800 x 55 x 6 mm polished 3650 g +041428 1053P/85 Stainless steel V2A 850 x 55 x 6 mm polished 3800 g +041435 1053P/90 Stainless steel V2A 900 x 55 x 6 mm polished 3950 g +041466 1053P/95 Stainless steel V2A 950 x 55 x 6 mm polished 4100 g +041473 1053P/100 Stainless steel V2A 1000 x 55 x 6 mm polished 4300 g +041367 1053P/110 Stainless steel V2A 1100 x 55 x 6 mm polished 4550 g +041374 1053P/120 Stainless steel V2A 1200 x 55 x 6 mm polished 4700 g +041381 1053P/130 Stainless steel V2A 1300 x 55 x 6 mm polished 4850 g +041398 1053P/140 Stainless steel V2A 1400 x 55 x 6 mm polished 5150 g +041404 1053P/150 Stainless steel V2A 1500 x 55 x 6 mm polished 5450 g +041411 1
HL053M/…. „In|Floor“ design shower channel made of matt stainless steel with integrated cross slopeHL053P/… „In|Floor“ design shower channel made of polished stainless steel with integrated cross slope
DataMaterial Stainless steel V2A (1.4301)Dimensions please see chartLoad classification K3 - max. 300 kgFits to HL53K(F), HL53KV(C), HL53K(F)CAdditional information
in combination with drain body HL53K(F), drainage strip with integrated cross slope; usage for floor tiles 12 - 32 mm and wall tiles 12 - 24 mm (incl. tile glue). may be cut to minimum length of 450mm
Including Installation accessories and lot cover
Installation Installation wallside or in the surface.
HL-No. Material Dimension Surface Weight EAN Piece/package053S/90 Stainless steel V2A 900 x 55 x 1,5 mm matt 1350 g +045211 1053S/100 Stainless steel V2A 1000 x 55 x 1,5 mm matt 1350 g +045198 1053S/120 Stainless steel V2A 1200 x 55 x 1,5 mm matt 1360 g +045204 1
HL053S/…. „In|Floor“ shower channel „Standard“ made of stainless steel with integrated cross slope
brushed: HL053M.1ENpolished: HL053P.1EN
HL053M/…. HL053P/…
HL053S/….
63
HL053WS
HL053WS.2E
HL053
HL053WS.1E
HL052.1E
DataMaterial Stainless steel V2A (1.4301)Dimensions please see chartLoad classification K3 - max. 300 kgFits to HL53K(F), HL53KV(C), HL53K(F)CAdditional information
Additional Installation in combination with drain body HL53-series, shower information channel with integrated cross slope and 2cm wallside angle. For floor tiles 12 - 32 mm and wall tiles 12 - 24 mm (incl. tile glue). Minimum cuttable size: 450mm
Including Installation accessories and lot cover
Installation Only close to the wall
HL-No. Material Dimension Surface Weight EAN Piece/package053WS/90 Stainless steel V2A 900 x 55 x 1,5 mm matt 1350 g +048991 1053WS/100 Stainless steel V2A 1000 x 55 x 1,5 mm matt 1360 g +048977 1053WS/120 Stainless steel V2A 1200 x 55 x 1,5 mm matt 1380 g +048984 1
HL053WS „Wall“ shower channel „standard“, stainless steel with wallside angle and integrated cross slope
HL053M.2/… „Wall“ DUO design shower channel, brushed stainless steel HL053P.2/… „Wall“ DUO design shower channel, polished stainless steel
HL052M „In|Floor“ short channel, brushed HL052P „In|Floor“ short channel, polished
Data
Material Massive stainless steel V2A (1.4301) - 6mm
Size See sheet belowLoad classification K3 - max. 300 kgFits to HL53K(F).2Additional information
Installation in combination with double drain body “Wall” DUO. Channel with 2 inlets and wall angle, position only close to the wall; Channel with lateral shaped slope. Usable for floor tiles from 10 to 24 mm and wall tiles from 12 - 24 mm (incl. tile glue)
Including Installation accessories and lot cover
Installation Only close to the wall
Data
Material Stainless steel V2A (1.4301)Size 52 x 302 mmLoad classification K3 - max. 300 kgFits to HL53K(F), HL53KV(C), HL53K(F)CAdditional information
Usage for all “In | Floor” drain bodies. Height from 11 to 38 mm
Including Installation accessories and lot cover
Installation Only close to the wall
HL-No. Material Dimension Surface Weight EAN Piece/packageHL053M.2/130 Stainless steel V2A 1300 x 60 x 25 mm matt 4700 g +047642 1HL053M.2/140 Stainless steel V2A 1400 x 60 x 25 mm matt 5050 g +047659 1HL053M.2/150 Stainless steel V2A 1500 x 60 x 25 mm matt 5330 g +047666 1HL053M.2/160 Stainless steel V2A 1600 x 60 x 25 mm matt 5490 g +047673 1HL053M.2/170 Stainless steel V2A 1700 x 60 x 25 mm matt 5560 g +047680 1HL053M.2/180 Stainless steel V2A 1800 x 60 x 25 mm matt 6000 g +047697 1HL053M.2/190 Stainless steel V2A 1900 x 60 x 25 mm matt 6100 g +047703 1HL053M.2/200 Stainless steel V2A 2000 x 60 x 25 mm matt 6400 g +047710 1HL053P.2/130 Stainless steel V2A 1300 x 60 x 25 mm polished 4670 g +047727 1HL053P.2/140 Stainless steel V2A 1400 x 60 x 25 mm polished 4920 g +047734 1HL053P.2/150 Stainless steel V2A 1500 x 60 x 25 mm polished 5200 g +047741 1HL053P.2/160 Stainless steel V2A 1600 x 60 x 25 mm polished 5470 g +047758 1HL053P.2/170 Stainless steel V2A 1700 x 60 x 25 mm polished 5750 g +047765 1HL053P.2/180 Stainless steel V2A 1800 x 60 x 25 mm polished 6120 g +047772 1HL053P.2/190 Stainless steel V2A 1900 x 60 x 25 mm polished 6280 g +047789 1HL053P.2/200 Stainless steel V2A 2000 x 60 x 25 mm polished 6550 g +047796 1
HL-No. Material Dimension Surface Weight EAN Piece/packageHL052M Edelstahl V2A 302 x 52 mm matt 4700 g +047642 1HL052P Edelstahl V2A 302 x 52 mm polished 5050 g +047659 1
brushed: HL053M.1DEpolished: HL053P.1DE
brushed: HL052M.2Epolished: HL052P.2E
HL053WS
HL053M.2/…HL053P.2/…
HL052MHL052P
64
HL0531.0E
50
499
73
79
DN50
1200 - min. 600
HL0531S
HL0531.1E
LX
3%
73
200
79
HL531 Shower channel „Primus Line“ with EPS installation block, stainless steel frame and cover , MIN. HEIGHT 79 MM !
Data
Description Shower channel, integrated in an EPS-installation block with stain-less steel frame and cover. Surface fleece laminated. For installation close to the wall.
Capacity 20 mm above drain level: HL531=0,6l/s; HL531i=0,48l/s 10 mm above drain level: HL53K.2=0,55l/s; HL53KF.2=0,4l/s
Material PP/ABS/EPS-40/stainless steelInlet Stainless steel frame 492 x 62 x13
mm, cover 480 x 50 mmOutlet DN50Standard EN 1253Trap Primus-trap, no stench without
water!Installation The exact adjustment of the
shower drain is made by simply cutting of the EPS element locally. It has a length from 600 mm to 1200 mm, or it can be extended with HL531V, width 200 mm, height 79 mm including 3% slope to the wall. It was designed for wall tiles up to 17 mm and floor tiles 13 mm (incl. adhesive). Also available as custom made with high stainless steel frame, for example, for natural stone. See also installation video at www.hl.at
HL-No. Material Dimension Weight EAN Piece/package531V-60 EPS-40 600 x 200 x 79 mm 557 g +036196 1
HL-No. Material Dimension Frame height Visible part Weight EAN Piece/Package 531 PP/ABS/EPS-40/stainless steel V2A 1200 x 200 x 79 mm 13 Polished stainless steel 2590 g +036158 1531.0 PP/ABS/EPS-40/stainless steel V2A 1200 x 200 x 79 mm 13 without cover 2178 g +036172 1531/18 PP/ABS/EPS-40/stainless steel V2A 1200 x 200 x 79 mm 18 Polished stainless steel 2690 g +037605 1531.0/18 PP/ABS/EPS-40/stainless steel V2A 1200 x 200 x 79 mm 18 without cover 2280 g +037636 1531/23 PP/ABS/EPS-40/stainless steel V2A 1200 x 200 x 79 mm 23 Polished stainless steel 2790 g +037612 1531.0/23 PP/ABS/EPS-40/stainless steel V2A 1200 x 200 x 79 mm 23 without cover 2380 g +037643 1531/28 PP/ABS/EPS-40/stainless steel V2A 1200 x 200 x 79 mm 28 Polished stainless steel 2890 g +037629 1531.0/28 PP/ABS/EPS-40/stainless steel V2A 1200 x 200 x 79 mm 28 without cover 2480 g +037650 1
HL531V Elongation element for HL531
Data
Material EPS-40Additional information
To elongate shower channel HL531, e.g. for multiple shower facilities. May be cut to any length, with fleece-laminated surface.
HL531
HL531V
65
HL0531S
HL0531D
HL0531I
HL0531S Standard cover for HL531HL0531D Design cover for HL531HL0531I Individual cover for HL531
Data
Material Stainless steel V2ADimensions HL0531I: Tile hollow:
474 x 44 mm, height 12 mm HL0531I/18: Tile hollow: 474 x 44 mm, height 17 mmHL0531I/23: Tile hollow: 474 x 44 mm, height 22 mmHL0531I/28: Tile hollow: 474 x 44 mm, height 27 mm
Load classification K3 - max. 300 kg
HL-Nr. Material Dimension Cover/colour Weight EAN Piece/Package0531S Stainless steel V2A 480 x 50 x 25,5 mm Stainless steel brushed 413 g +036257 10531D Stainless steel V2A 480 x 50 x 25,5 mm Stainless steel brushed 946 g +036233 10531I Stainless steel V2A 480 x 50 x 25,5 mm Stainless steel brushed 10531S/18 Stainless steel V2A 480 x 50 x 30,5 mm Stainless steel brushed 490 g +037575 10531D/18 Stainless steel V2A 480 x 50 x 30,5 mm Stainless steel brushed 1030 g +037544 10531I/18 Stainless steel V2A 480 x 50 x 30,5 mm Stainless steel brushed 10531S/23 Stainless steel V2A 480 x 50 x 35,5 mm Stainless steel brushed 570 g +037582 10531D/23 Stainless steel V2A 480 x 50 x 35,5 mm Stainless steel brushed 1110 g +037551 10531I/23 Stainless steel V2A 480 x 50 x 35,5 mm Stainless steel brushed 10531S/28 Stainless steel V2A 480 x 50 x 40,5 mm Stainless steel brushed 650 g +037599 10531D/28 Stainless steel V2A 480 x 50 x 40,5 mm Stainless steel brushed 1190 g + 037568 10531I/28 Stainless steel V2A 480 x 50 x 40,5 mm Stainless steel brushed 1
HL0531SHL0531DHL0531I
66
HL03910.1E
HL03900.0E
HL0540.2E
HL2040
HL0540.4E
HL0540.0E
HL0540.3E
HL540K
HL066C.1EHL066Q.1E HL0540I
HL0540I
HL540 HL540I
HL0540.5E
HL2040I
Quadra Cut Individuell
HL3928 HL3128E
Data
Capacity 20 mm above drain level: HL540=0,8l/s; HL540i=0,6/s10 mm above drain level: HL540=0,55l/s; HL540i=0,45l/s
Material PP/stainless steel, Frame: V4AGrate HL540=V2AGrate HL540i=V4A
Outlet DN50 horizontalHeight from 8 - 20 cm adjustableStandard EN 1253Stench trap 5cm seal water, incl. Primus-trap,
no stench without seal waterAdditional information
incl. removable trap inlet, sealing kit with textile coated membrane, sound disconnected adjusting angles, protection cover and lot cover
Installation The drain body might be fixed on the floor with 3 metal angles and can be adjusted in height afterwards. Advantage: maximum sceed covering of the outlet pipe. New: It is no longer necessary to set the drain exactly on the right height of the screed. After filling in the screed, the salient nozzle is cut by a saw. The sealing kit may be inserted without any tools and takes care of a safe connection to the waterproofing. At the end the extension is adjusted and set into the drain. Please take care, that the edges of the frame are underlaid with tile glue to take maximum load.
HL066Q.1E, HL066C.1E, HL0540I, HL3928, HL3128E Design grates
Data
Material Stainless steel V4AGrate HL540I: 138x138mm massive,
Tile hollow: 74x74 mm, depth 13mm
Load classification HL540: L - max. 1,5t,HL540i: K3 - max. 300kg
Recommended for Shower drain HL540 or floor drain series HL5100, HL3100, HL72.1 and HL317
HL540 „Primus Drain“ Shower drain, MIN. HEIGHT 80 MM !HL540I „Primus Drain“ Shower drain with individual tile hollow, MIN. HEIGHT 80 MM !
HL-No. Material Dimension Weight EAN Piece/package540 PP/Stainless steel DN50 1533 g +039029 1540I PP/Stainless steel DN50 1898 g +039098 1540-Quadra PP/Stainless steel DN50 1898 g +041817 1540-Cut PP/Stainless steel DN50 1898 g +041800 1540-Hamam PP/Stainless steel/
PVD-coatedDN50 1898 g +041824 1
HL-No. Material Dimension Weight EAN Piece/package066Q.1E Stainless steel V4A 138 x 138 x 5 mm 607 g +013623 1 066C.1E Stainless steel V4A 138 x 138 x 5 mm 608 g +031283 10540I Stainless steel V4A 138 x 138 x 5 mm 638 g +039104 13928 Stainless steel/PVD coated V4A 138 x 138 x 5 mm 608 g +031283 13128E Stainless steel V4A 138 x 138 x 5 mm 1
Hamam (Stainless steel/PVD coated) Hamam (Stainless steel)
Please also see installation movie at
www. hl.at
HL540HL540I
HL066Q.1E, HL066C.1E, HL0540I, HL3928, HL3128E
67
HL0541.0E
HL0541.3E
HL541K
HL0540I
HL541 HL541I
HL0541.5E
HL0541.4E
HL3120 HL3121 HL3122
HL3124 HL3125
HL3127HL0541I
115 x 115 5
HL3123
HL037N.0E
HL0541.2E
HL2020
HL037Pr.1E
Data
Capacity 20 mm above drain level: HL541=0,5l/s; HL541i=0,45/s10 mm above drain level: HL541=0,4l/s; HL541i=0,4l/s
Material PP/stainless steel, Frame: V4AGrate HL541=V2AGrate HL541i=V4A
Outlet DN40/DN50 horizontalHeight from 62 - 200 (230) mmStandard EN 1253Load classification K3 - max. 300 kgStench trap „Primus blue“ trap, no
stench without seal waterAdditional information
Incl. removable trap inlet, sealing kit with textile coated membrane, adjustable fixing angles, lot cover and protection cover
Installation The drain body might be fixed on the floor with 3 metal angles and can be adjusted in height afterwards. Advantage: maximum sceed covering of the outlet pipe. New: It is no longer necessary to set the drain exactly on the right height of the screed. After filling in the screed, the salient nozzle is cut by a saw. The sealing kit may be inserted without any tools and takes care of a safe connection to the waterproofing. At the end the extension is adjusted and set into the drain. Please take care, that the edges of the frame are underlaid with tile glue to take maximum load.
HL541 Primus blue Flat shower drain, MIN. HEIGHT 62MM!HL541I Primus blue Flat shower drain with individual tile hollow, MIN. HEIGHT 62MM!
HL-No. Material Dimension Weight EAN Piece/packageHL541 PP/Stainless steel DN40/50 - +047642 1HL541I PP/Stainless steel DN40/50 - +047659 1HL541-Quadra PP/Stainless steel DN40/50 - - 1
HL0541I, HL3120, HL3121, HL3122, HL3123, HL3124, HL3125, HL3127 Design grates
HL-No. Dimension Weight EAN Piece/package3120 115 x 115 mm 425 g +015412 13121 115 x 115 mm 425 g +015429 13122 115 x 115 mm 425 g +015443 13123 115 x 115 mm 425 g +015443 13124 115 x 115 mm 425 g +015450 13125 115 x 115 mm 425 g +015467 13127 115 x 115 mm 430 g +029037 10541I 115 x 115 mm 800 g +048304 1
Daten
Material Stainless steel V4AGrate Stainless steel grate 115 x 115 mmLoad classification L – max. 1,5 tRecommended for Floor drain series HL70, HL80,
HL300, HL304, HL310N, HL510N, HL90 combined with extensions HL3200 or HL3210HL0541I: HL541
Please also see installation movie and
movie „function of Primus blue“
at www.hl.at
HL541HL541I
HL0541I, HL3120, HL3121, HL3122, HL3123, HL3124, HL3125, HL3127
68
HL037Pr.1E
HL037N.0EHL3200
HL0510.7EKK
HL0510NC.1E
HL0510NCN.2E
HL510NCK
HL510NC Floor drain with polymer concrete collar
Data
Capacity 20 mm above drain level: 0,55l/s10 mm above drain level: 0,4l/s
Material Polymer concrete/steel mesh/PPOutlet dimension DN40/50 horizontalHeight 95 mmStandard EN 1253Height of seal water 50 mmAdditional information
removable trap, polymer concrete collar with steel mesh reinforce-ment for a save connection to the under-tile waterproofing and glassfiber pad.
Including Sound-absorbing levelling legs for adjustment in height, lot cover and supporting frame
HL-No. Material Dimension Weight EAN Piece/package510NC Polymer concrete/
steel mesh/PPDN40/50 4350 g +021338 1
Installation example with epoxy coating
HL510NC